OpenWrt/LEDE Project

Welcome to the OpenWrt Project bug reporting and issue tracking system

Problems to be reported here are for the current OpenWrt and legacy LEDE Project’s targets, sources, toolchain, core packages, build procedures, distribution and infrastructure. Guidelines for submitting a good bug report can be found at the OpenWrt Project website. Problems related to LuCI or OpenWrt packages need to be reported in their repositories:

Notifications of all submissions and task changes are sent to openwrt-bugs@infradead.org.

OpenedIDCategoryTask TypePrioritySeverity  descSummaryReported InStatus
12.12.20192670KernelBug ReportVery LowHigh[ATH79] unstable USB on WR1043 v2openwrt-19.07Unconfirmed Task Description

Hi there!

I recently upgraded my TP-Link TL-WR1043 v2 device to the ath79 targeted 19.07-rc2 release using my custom build, which I have compiled with the image builder.

make image PROFILE=tplink_tl-wr1043nd-v2 PACKAGES="block-mount curl diffutils ethtool iperf3 iwinfo htop kmod-fs-ext4 kmod-usb-storage luci mailsend-nossl minidlna nfs-kernel-server ppp-mod-pppoe shadow-su transmission-daemon-mbedtls transmission-web vsftpd zram-swap -ip6tables -kmod-ip6tables -kmod-ipv6 -kmod-nf-conntrack6 -kmod-nf-ipt6 -libopenssl1.1 -odhcp6c -odhcpd-ipv6only -luci-proto-ipv6 -libip6tc2"

I just recently rolled back to an EXT4 partition, because of it's smaller memory footprint. (just mounting a ~50GB f2fs partition consumes around 10MBs of memory)
So in the very first attempt I wanted to copy back everything to my Transcend 790K. But after the first 500-1000 MBs(mix of archives, image, text and video files), the transaction speed has fallen down couple of times. I thought maybe the passive FTP connection was the problem, because after a few automatic reconnect attempts, the speed of the copy has been normalized again and in the end the device was connected. Later I found that the USB devices was reseted.
I had another try with a Sandisk Ultra Fit drive (SDCZ-43), but the result and the configuration was pretty sam. ~50GB EXT4 partition without journal and without barrier.
I force upgraded the machine to the ar71xx target and Filezilla so far copied back 16GBs without any problem.
Target ATH79 seem to be has so many problems with the USB subsystem, please see my other bugreport for the WDR4300 as well: FS#2567 - [ATH79] USB speed degradation on WDR4300.

Let me know if I can help the bughunting any way,
thanks and regards!

09.01.20202719Base systemBug ReportVery LowHighBuffalo WBMR-HP-G300H: DSL does not connect at all with...openwrt-19.07Unconfirmed Task Description

Supply the following if possible:
- Device problem occurs on: Buffalo WBMR-HP-G300H
- Software versions of OpenWrt/LEDE release, packages, etc.: OpenWRT 19.07, kmod-ltq-adsl-ar9-fw-a 0.1-1, which shows up as 4.4.4.0.0.1 in dsl_control status.
- Steps to reproduce:

1. Get an ADSL line from Rostelecom.
2. Upgrade the router to OpenWRT 19.07.
3. Reboot.

Result: DSL does not connect. In /etc/init.d/dsl_control status, it goes through all phases, then briefly shows as “Up”, but then the “dsl0” interface is not created, and the following lines are logged in dmesg:

 [   56.597766] [DSL_BSP_Showtime 914]: Datarate US intl = 1024000, fast = 0
 [   56.603091] [DSL_BSP_Showtime 934]: no hookup from ATM driver to set cell rate

The error does not exist with the 4.5.4.9.1.1 firmware obtained from unofficial sources. The bug has been submitted through the affected ADSL line with the unofficial firmware.

Status:

# /etc/init.d/dsl_control status
ATU-C Vendor ID: Broadcom 161.149
ATU-C System Vendor ID: 00,00,00,00,00,00,00,00
Chipset: Ifx-AR9
Firmware Version: 4.5.4.9.1.1
API Version: 3.24.4.4
XTSE Capabilities: 0×4, 0×0, 0×0, 0×0, 0×0, 0×0, 0×0, 0×0 Annex: A
Line Mode: G.992.1 (ADSL)
Profile:
Line State: UP [0×801: showtime_tc_sync]
Forward Error Correction Seconds (FECS): Near: 413342 / Far: 0
Errored seconds (ES): Near: 0 / Far: 0
Severely Errored Seconds (SES): Near: 0 / Far: 0
Loss of Signal Seconds (LOSS): Near: 0 / Far: 0
Unavailable Seconds (UAS): Near: 253 / Far: 253
Header Error Code Errors (HEC): Near: 0 / Far: 0
Non Pre-emtive CRC errors (CRC_P): Near: / Far:
Pre-emtive CRC errors (CRCP_P): Near: / Far:
Power Management Mode: L0 - Synchronized
Latency [Interleave Delay]: 8.0 ms [Interleave] 8.0 ms [Interleave]
Data Rate: Down: 9.952 Mb/s / Up: 1.024 Mb/s
Line Attenuation (LATN): Down: 32.2 dB / Up: 19.5 dB
Signal Attenuation (SATN): Down: 32.6 dB / Up: 19.5 dB
Noise Margin (SNR): Down: 6.1 dB / Up: 13.0 dB
Aggregate Transmit Power (ACTATP): Down: 20.0 dB / Up: 12.3 dB
Max. Attainable Data Rate (ATTNDR): Down: 8.848 Mb/s / Up: 1.204 Mb/s
Line Uptime Seconds: 1164
Line Uptime: 19m 24s

(yes, very bad line)

Config:

config atm-bridge ‘atm’

option vpi '1'
option encaps 'llc'
option payload 'bridged'
option nameprefix 'dsl'
option vci '50'
option unit '0'
option atmdev '0'

config dsl ‘dsl’

option annex 'a'
option firmware '/lib/firmware/dsl_ar9_firmware_adsl_a-04.05.04.09.01.01.bin'

config interface ‘wan’

option ifname 'dsl0'
option proto 'pppoe'
option ipv6 '1'
option username 'censored'
list dns '8.8.8.8'
list dns '8.8.4.4'
option peerdns '0'
option keepalive '60 5'
option password 'censored'
09.01.20202720PackagesBuild FailureVery LowHighlibcap compile failure at tests stepTrunkUnconfirmed Task Description

libcap build is failing since the update to 2.30

+ The toolchain options used are:
  - binutils 2.31.1
  - gcc 8.x
  - glibc

For reproducing one just need to run the folling

 $make package/feeds/packages/libcap/compile V=s

The flow breaks at tests stage:

make -C tests all
make[4]: Entering directory ‘/data/workspace/hbk/Perception/Embedded/OpenWrt/build_dir/target-i386_pentium4_glibc/libcap-2.30/tests’ i486-openwrt-linux-gnu-gcc -Os -pipe -march=pentium4 -fno-caller-saves -fno-plt -fhonour-copts -Wno-error=unused-but-set-variable -Wno-error=unused-result -ffile-prefix-map=/data/workspace/hbk/Perception/Embedded/OpenWrt/build_dir/target-i386_pentium4_glibc/libcap-2.30=libcap-2.30 -Wformat -Werror=format-security -D_FORTIFY_SOURCE=1 -Wl,-z,now -Wl,-z,relro -fPIC -I/data/workspace/hbk/Perception/Embedded/OpenWrt/build_dir/target-i386_pentium4_glibc/libcap-2.30/tests/../libcap/include/uapi -I/data/workspace/hbk/Perception/Embedded/OpenWrt/build_dir/target-i386_pentium4_glibc/libcap-2.30/tests/../libcap/include libcap_psx_test.c -o libcap_psx_test -L/data/workspace/hbk/Perception/Embedded/OpenWrt/build_dir/target-i386_pentium4_glibc/libcap-2.30/tests/../libcap -lcap -L/data/workspace/hbk/Perception/Embedded/OpenWrt/build_dir/target-i386_pentium4_glibc/libcap-2.30/tests/../libcap -lpsx -lpthread -Wl,-wrap,pthread_create –static
/data/workspace/hbk/Perception/Embedded/OpenWrt/staging_dir/toolchain-i386_pentium4_gcc-8.3.0_glibc/lib/gcc/i486-openwrt-linux-gnu/8.3.0/../../../../i486-openwrt-linux-gnu/bin/ld: /data/workspace/hbk/Perception/Embedded/OpenWrt/staging_dir/toolchain-i386_pentium4_gcc-8.3.0_glibc/lib/gcc/i486-openwrt-linux-gnu/8.3.0/../../../../i486-openwrt-linux-gnu/lib/libc.a(iofclose.o): in function `_IO_new_fclose.cold.0’:
iofclose.c:(.text.unlikely+0×34): undefined reference to `_Unwind_Resume’ /data/workspace/hbk/Perception/Embedded/OpenWrt/staging_dir/toolchain-i386_pentium4_gcc-8.3.0_glibc/lib/gcc/i486-openwrt-linux-gnu/8.3.0/../../../../i486-openwrt-linux-gnu/bin/ld: /data/workspace/hbk/Perception/Embedded/OpenWrt/staging_dir/toolchain-i386_pentium4_gcc-8.3.0_glibc/lib/gcc/i486-openwrt-linux-gnu/8.3.0/../../../../i486-openwrt-linux-gnu/lib/libc.a(iofclose.o):(.eh_frame+0×13): undefined reference to `gcc_personality_v0’ /data/workspace/hbk/Perception/Embedded/OpenWrt/staging_dir/toolchain-i386_pentium4_gcc-8.3.0_glibc/lib/gcc/i486-openwrt-linux-gnu/8.3.0/../../../../i486-openwrt-linux-gnu/bin/ld: /data/workspace/hbk/Perception/Embedded/OpenWrt/staging_dir/toolchain-i386_pentium4_gcc-8.3.0_glibc/lib/gcc/i486-openwrt-linux-gnu/8.3.0/../../../../i486-openwrt-linux-gnu/lib/libc.a(iofclose.o):(.eh_frame+0x6f): undefined reference to `gcc_personality_v0’ /data/workspace/hbk/Perception/Embedded/OpenWrt/staging_dir/toolchain-i386_pentium4_gcc-8.3.0_glibc/lib/gcc/i486-openwrt-linux-gnu/8.3.0/../../../../i486-openwrt-linux-gnu/bin/ld: /data/workspace/hbk/Perception/Embedded/OpenWrt/staging_dir/toolchain-i386_pentium4_gcc-8.3.0_glibc/lib/gcc/i486-openwrt-linux-gnu/8.3.0/../../../../i486-openwrt-linux-gnu/lib/libc.a(iofflush.o): in function `_IO_fflush.cold.0’:
iofflush.c:(.text.unlikely+0×34): undefined reference to `_Unwind_Resume’ /data/workspace/hbk/Perception/Embedded/OpenWrt/staging_dir/toolchain-i386_pentium4_gcc-8.3.0_glibc/lib/gcc/i486-openwrt-linux-gnu/8.3.0/../../../../i486-openwrt-linux-gnu/bin/ld: /data/workspace/hbk/Perception/Embedded/OpenWrt/staging_dir/toolchain-i386_pentium4_gcc-8.3.0_glibc/lib/gcc/i486-openwrt-linux-gnu/8.3.0/../../../../i486-openwrt-linux-gnu/lib/libc.a(iofflush.o):(.eh_frame+0×13): undefined reference to `gcc_personality_v0’ /data/workspace/hbk/Perception/Embedded/OpenWrt/staging_dir/toolchain-i386_pentium4_gcc-8.3.0_glibc/lib/gcc/i486-openwrt-linux-gnu/8.3.0/../../../../i486-openwrt-linux-gnu/bin/ld: /data/workspace/hbk/Perception/Embedded/OpenWrt/staging_dir/toolchain-i386_pentium4_gcc-8.3.0_glibc/lib/gcc/i486-openwrt-linux-gnu/8.3.0/../../../../i486-openwrt-linux-gnu/lib/libc.a(iofflush.o):(.eh_frame+0×73): undefined reference to `gcc_personality_v0’ /data/workspace/hbk/Perception/Embedded/OpenWrt/staging_dir/toolchain-i386_pentium4_gcc-8.3.0_glibc/lib/gcc/i486-openwrt-linux-gnu/8.3.0/../../../../i486-openwrt-linux-gnu/bin/ld: /data/workspace/hbk/Perception/Embedded/OpenWrt/staging_dir/toolchain-i386_pentium4_gcc-8.3.0_glibc/lib/gcc/i486-openwrt-linux-gnu/8.3.0/../../../../i486-openwrt-linux-gnu/lib/libc.a(ioputs.o): in function `_IO_puts.cold.0’:
ioputs.c:(.text.unlikely+0×34): undefined reference to `_Unwind_Resume’ /data/workspace/hbk/Perception/Embedded/OpenWrt/staging_dir/toolchain-i386_pentium4_gcc-8.3.0_glibc/lib/gcc/i486-openwrt-linux-gnu/8.3.0/../../../../i486-openwrt-linux-gnu/bin/ld: /data/workspace/hbk/Perception/Embedded/OpenWrt/staging_dir/toolchain-i386_pentium4_gcc-8.3.0_glibc/lib/gcc/i486-openwrt-linux-gnu/8.3.0/../../../../i486-openwrt-linux-gnu/lib/libc.a(ioputs.o):(.eh_frame+0×13): undefined reference to `gcc_personality_v0’ /data/workspace/hbk/Perception/Embedded/OpenWrt/staging_dir/toolchain-i386_pentium4_gcc-8.3.0_glibc/lib/gcc/i486-openwrt-linux-gnu/8.3.0/../../../../i486-openwrt-linux-gnu/bin/ld: /data/workspace/hbk/Perception/Embedded/OpenWrt/staging_dir/toolchain-i386_pentium4_gcc-8.3.0_glibc/lib/gcc/i486-openwrt-linux-gnu/8.3.0/../../../../i486-openwrt-linux-gnu/lib/libc.a(ioputs.o):(.eh_frame+0×77): undefined reference to `gcc_personality_v0’ /data/workspace/hbk/Perception/Embedded/OpenWrt/staging_dir/toolchain-i386_pentium4_gcc-8.3.0_glibc/lib/gcc/i486-openwrt-linux-gnu/8.3.0/../../../../i486-openwrt-linux-gnu/bin/ld: /data/workspace/hbk/Perception/Embedded/OpenWrt/staging_dir/toolchain-i386_pentium4_gcc-8.3.0_glibc/lib/gcc/i486-openwrt-linux-gnu/8.3.0/../../../../i486-openwrt-linux-gnu/lib/libc.a(wfileops.o): in function `_IO_wfile_underflow.cold.2’:
wfileops.c:(.text.unlikely+0×34): undefined reference to `_Unwind_Resume’ /data/workspace/hbk/Perception/Embedded/OpenWrt/staging_dir/toolchain-i386_pentium4_gcc-8.3.0_glibc/lib/gcc/i486-openwrt-linux-gnu/8.3.0/../../../../i486-openwrt-linux-gnu/bin/ld: /data/workspace/hbk/Perception/Embedded/OpenWrt/staging_dir/toolchain-i386_pentium4_gcc-8.3.0_glibc/lib/gcc/i486-openwrt-linux-gnu/8.3.0/../../../../i486-openwrt-linux-gnu/lib/libc.a(wfileops.o):(.eh_frame+0x6b): undefined reference to `gcc_personality_v0’ /data/workspace/hbk/Perception/Embedded/OpenWrt/staging_dir/toolchain-i386_pentium4_gcc-8.3.0_glibc/lib/gcc/i486-openwrt-linux-gnu/8.3.0/../../../../i486-openwrt-linux-gnu/bin/ld: /data/workspace/hbk/Perception/Embedded/OpenWrt/staging_dir/toolchain-i386_pentium4_gcc-8.3.0_glibc/lib/gcc/i486-openwrt-linux-gnu/8.3.0/../../../../i486-openwrt-linux-gnu/lib/libc.a(wfileops.o):(.eh_frame+0x12b): undefined reference to `gcc_personality_v0’ /data/workspace/hbk/Perception/Embedded/OpenWrt/staging_dir/toolchain-i386_pentium4_gcc-8.3.0_glibc/lib/gcc/i486-openwrt-linux-gnu/8.3.0/../../../../i486-openwrt-linux-gnu/bin/ld: /data/workspace/hbk/Perception/Embedded/OpenWrt/staging_dir/toolchain-i386_pentium4_gcc-8.3.0_glibc/lib/gcc/i486-openwrt-linux-gnu/8.3.0/../../../../i486-openwrt-linux-gnu/lib/libc.a(fileops.o): in function `_IO_new_file_underflow.cold.6’:
fileops.c:(.text.unlikely+0×38): undefined reference to `_Unwind_Resume’ /data/workspace/hbk/Perception/Embedded/OpenWrt/staging_dir/toolchain-i386_pentium4_gcc-8.3.0_glibc/lib/gcc/i486-openwrt-linux-gnu/8.3.0/../../../../i486-openwrt-linux-gnu/bin/ld: /data/workspace/hbk/Perception/Embedded/OpenWrt/staging_dir/toolchain-i386_pentium4_gcc-8.3.0_glibc/lib/gcc/i486-openwrt-linux-gnu/8.3.0/../../../../i486-openwrt-linux-gnu/lib/libc.a(fileops.o):(.eh_frame+0×103): undefined reference to `gcc_personality_v0’ /data/workspace/hbk/Perception/Embedded/OpenWrt/staging_dir/toolchain-i386_pentium4_gcc-8.3.0_glibc/lib/gcc/i486-openwrt-linux-gnu/8.3.0/../../../../i486-openwrt-linux-gnu/bin/ld: /data/workspace/hbk/Perception/Embedded/OpenWrt/staging_dir/toolchain-i386_pentium4_gcc-8.3.0_glibc/lib/gcc/i486-openwrt-linux-gnu/8.3.0/../../../../i486-openwrt-linux-gnu/lib/libc.a(fileops.o):(.eh_frame+0x17f): undefined reference to `gcc_personality_v0’ /data/workspace/hbk/Perception/Embedded/OpenWrt/staging_dir/toolchain-i386_pentium4_gcc-8.3.0_glibc/lib/gcc/i486-openwrt-linux-gnu/8.3.0/../../../../i486-openwrt-linux-gnu/bin/ld: /data/workspace/hbk/Perception/Embedded/OpenWrt/staging_dir/toolchain-i386_pentium4_gcc-8.3.0_glibc/lib/gcc/i486-openwrt-linux-gnu/8.3.0/../../../../i486-openwrt-linux-gnu/lib/libc.a(iofputs.o): in function `_IO_fputs.cold.0’:
iofputs.c:(.text.unlikely+0×34): undefined reference to `_Unwind_Resume’ /data/workspace/hbk/Perception/Embedded/OpenWrt/staging_dir/toolchain-i386_pentium4_gcc-8.3.0_glibc/lib/gcc/i486-openwrt-linux-gnu/8.3.0/../../../../i486-openwrt-linux-gnu/bin/ld: /data/workspace/hbk/Perception/Embedded/OpenWrt/staging_dir/toolchain-i386_pentium4_gcc-8.3.0_glibc/lib/gcc/i486-openwrt-linux-gnu/8.3.0/../../../../i486-openwrt-linux-gnu/lib/libc.a(iofputs.o):(.eh_frame+0×13): undefined reference to `gcc_personality_v0’ /data/workspace/hbk/Perception/Embedded/OpenWrt/staging_dir/toolchain-i386_pentium4_gcc-8.3.0_glibc/lib/gcc/i486-openwrt-linux-gnu/8.3.0/../../../../i486-openwrt-linux-gnu/bin/ld: /data/workspace/hbk/Perception/Embedded/OpenWrt/staging_dir/toolchain-i386_pentium4_gcc-8.3.0_glibc/lib/gcc/i486-openwrt-linux-gnu/8.3.0/../../../../i486-openwrt-linux-gnu/lib/libc.a(iofputs.o):(.eh_frame+0x8f): undefined reference to `gcc_personality_v0’ /data/workspace/hbk/Perception/Embedded/OpenWrt/staging_dir/toolchain-i386_pentium4_gcc-8.3.0_glibc/lib/gcc/i486-openwrt-linux-gnu/8.3.0/../../../../i486-openwrt-linux-gnu/bin/ld: /data/workspace/hbk/Perception/Embedded/OpenWrt/staging_dir/toolchain-i386_pentium4_gcc-8.3.0_glibc/lib/gcc/i486-openwrt-linux-gnu/8.3.0/../../../../i486-openwrt-linux-gnu/lib/libc.a(iofwrite.o): in function `_IO_fwrite.cold.0’:
iofwrite.c:(.text.unlikely+0×34): undefined reference to `_Unwind_Resume’ /data/workspace/hbk/Perception/Embedded/OpenWrt/staging_dir/toolchain-i386_pentium4_gcc-8.3.0_glibc/lib/gcc/i486-openwrt-linux-gnu/8.3.0/../../../../i486-openwrt-linux-gnu/bin/ld: /data/workspace/hbk/Perception/Embedded/OpenWrt/staging_dir/toolchain-i386_pentium4_gcc-8.3.0_glibc/lib/gcc/i486-openwrt-linux-gnu/8.3.0/../../../../i486-openwrt-linux-gnu/lib/libc.a(iofwrite.o):(.eh_frame+0×13): undefined reference to `gcc_personality_v0’ /data/workspace/hbk/Perception/Embedded/OpenWrt/staging_dir/toolchain-i386_pentium4_gcc-8.3.0_glibc/lib/gcc/i486-openwrt-linux-gnu/8.3.0/../../../../i486-openwrt-linux-gnu/bin/ld: /data/workspace/hbk/Perception/Embedded/OpenWrt/staging_dir/toolchain-i386_pentium4_gcc-8.3.0_glibc/lib/gcc/i486-openwrt-linux-gnu/8.3.0/../../../../i486-openwrt-linux-gnu/lib/libc.a(iofwrite.o):(.eh_frame+0x7f): undefined reference to `gcc_personality_v0’ /data/workspace/hbk/Perception/Embedded/OpenWrt/staging_dir/toolchain-i386_pentium4_gcc-8.3.0_glibc/lib/gcc/i486-openwrt-linux-gnu/8.3.0/../../../../i486-openwrt-linux-gnu/bin/ld: /data/workspace/hbk/Perception/Embedded/OpenWrt/staging_dir/toolchain-i386_pentium4_gcc-8.3.0_glibc/lib/gcc/i486-openwrt-linux-gnu/8.3.0/../../../../i486-openwrt-linux-gnu/lib/libc.a(iogetdelim.o): in function `_IO_getdelim.cold.0’:
iogetdelim.c:(.text.unlikely+0×35): undefined reference to `_Unwind_Resume’ /data/workspace/hbk/Perception/Embedded/OpenWrt/staging_dir/toolchain-i386_pentium4_gcc-8.3.0_glibc/lib/gcc/i486-openwrt-linux-gnu/8.3.0/../../../../i486-openwrt-linux-gnu/bin/ld: /data/workspace/hbk/Perception/Embedded/OpenWrt/staging_dir/toolchain-i386_pentium4_gcc-8.3.0_glibc/lib/gcc/i486-openwrt-linux-gnu/8.3.0/../../../../i486-openwrt-linux-gnu/lib/libc.a(iogetdelim.o):(.eh_frame+0×13): undefined reference to `gcc_personality_v0’ /data/workspace/hbk/Perception/Embedded/OpenWrt/staging_dir/toolchain-i386_pentium4_gcc-8.3.0_glibc/lib/gcc/i486-openwrt-linux-gnu/8.3.0/../../../../i486-openwrt-linux-gnu/bin/ld: /data/workspace/hbk/Perception/Embedded/OpenWrt/staging_dir/toolchain-i386_pentium4_gcc-8.3.0_glibc/lib/gcc/i486-openwrt-linux-gnu/8.3.0/../../../../i486-openwrt-linux-gnu/lib/libc.a(iogetdelim.o):(.eh_frame+0x8f): undefined reference to `gcc_personality_v0’ /data/workspace/hbk/Perception/Embedded/OpenWrt/staging_dir/toolchain-i386_pentium4_gcc-8.3.0_glibc/lib/gcc/i486-openwrt-linux-gnu/8.3.0/../../../../i486-openwrt-linux-gnu/bin/ld: /data/workspace/hbk/Perception/Embedded/OpenWrt/staging_dir/toolchain-i386_pentium4_gcc-8.3.0_glibc/lib/gcc/i486-openwrt-linux-gnu/8.3.0/../../../../i486-openwrt-linux-gnu/lib/libpthread.a(unwind.o): in function `unwind_stop’:
unwind.c:(.text+0×47): undefined reference to `_Unwind_GetCFA’ /data/workspace/hbk/Perception/Embedded/OpenWrt/staging_dir/toolchain-i386_pentium4_gcc-8.3.0_glibc/lib/gcc/i486-openwrt-linux-gnu/8.3.0/../../../../i486-openwrt-linux-gnu/bin/ld: unwind.c:(.text+0×88): undefined reference to `_Unwind_GetCFA’ /data/workspace/hbk/Perception/Embedded/OpenWrt/staging_dir/toolchain-i386_pentium4_gcc-8.3.0_glibc/lib/gcc/i486-openwrt-linux-gnu/8.3.0/../../../../i486-openwrt-linux-gnu/bin/ld: unwind.c:(.text+0xed): undefined reference to `_Unwind_GetCFA’ /data/workspace/hbk/Perception/Embedded/OpenWrt/staging_dir/toolchain-i386_pentium4_gcc-8.3.0_glibc/lib/gcc/i486-openwrt-linux-gnu/8.3.0/../../../../i486-openwrt-linux-gnu/bin/ld: /data/workspace/hbk/Perception/Embedded/OpenWrt/staging_dir/toolchain-i386_pentium4_gcc-8.3.0_glibc/lib/gcc/i486-openwrt-linux-gnu/8.3.0/../../../../i486-openwrt-linux-gnu/lib/libpthread.a(unwind.o): in function `__pthread_unwind’:
unwind.c:(.text+0×156): undefined reference to `_Unwind_ForcedUnwind’ collect2: error: ld returned 1 exit status

15.01.20202739Base systemBug ReportVery LowHighArbitrary File CreationAllUnconfirmed Task Description

There is no restriction on the path of the system log file(logread),which lead to overwritten important file,such as /etc/passwd. if /etc/passwd was overwritened,it will cause a denial of service. when a router was infected, The only way to fix is flash firmware.

In the background, function External Linkstart_service_file will deal the system logging request and use logread` to save log in specified file.

 PROG=/sbin/logread  
    
    start_service_file()                                                              
    {                                                                                 
            PIDCOUNT="$(( ${PIDCOUNT} + 1))"                                          
            local pid_file="/var/run/logread.${PIDCOUNT}.pid"                         
                                                                                      
            [ "$2" = 0 ] || {                                                         
                    echo "validation failed"                                          
                    return 1                                                          
            }                                                                         
            [ -z "${log_file}" ] && return                                            
                                                                                      
            mkdir -p "$(dirname "${log_file}")"                                       
                                                                                      
            procd_open_instance                                                       
            procd_set_param command "$PROG" -f -F "$log_file" -p "$pid_file"          
            [ -n "${log_size}" ] && procd_append_param command -S "$log_size"         
            procd_close_instance                                                      
    }   

POC

1. set the path of sustem log and buffer size

In System → logging page,System log buffer sizeset to 1KiB ,Write system log to file set to /etc/passwd. At the end , clicking “Save & Apply” button.

2. reboot or wait a moment

In order to produce some log to overwriten /etc/passwd , it need to reboot OpenWrt (the fasest way ) or wait a monent.

3. result

Denial of service: the LuCi web page display “Dad Gateway”. the same time , the internet was offline.

22.01.20202764Base systemBug ReportVery LowHighucert: ucert -A output is invalidTrunkUnconfirmed Task Description

ucert -A generates something that ucert cannot read back.

This happens because ucert -A appears to be appending several libubox “blobs” together, but cert_load() uses libubox’ blob_parse_untrusted() which expects to get a buffer with a single blob inside, and no padding.

Thus a valid ucert file with certificate and signature will be *bigger* than the first blob inside it, and blob_parse_untrusted() in libubox won’t even try to process it.

Since this renders ucert useless, severity is set to high.

This is related to  FS#2762  and FS#2763

24.01.20202768ToolchainBug ReportVery LowHighmake_ext4fs: Name-Based UUID leads to collisionTrunkUnconfirmed Task Description

make_ext4fs uses name-based uuid generation (see https://tools.ietf.org/html/rfc4122#section-4.3).

Therefore, as the uuid generation does only depend on the Filesystem Label and an hardcoded namespace, the UUID is exactly identical for multiple different filesystems with the same label (see https://git.openwrt.org/?p=project/make_ext4fs.git;a=blob;f=ext4_utils.c;h=1a886d7e86262d35e30d894f821ca91d32384e96;hb=HEAD#l224).

This can lead to problems like the inability to mount an filesystem by UUID.
In my constellation, I have an MMC Storage and an external SD-Card, both flashed with filesystems generated by make_ext4fs. They both have the same UUID, therefore it’s impossible to distinguish/mount them by UUID.

My suggestion would be to replace “info.label” as parameter for “generate_uuid” trough another, better suited value, e.g. an hash of the make_ext4fs directory content. Maybe it should be considered to switch to an Random Number-based UUID (https://tools.ietf.org/html/rfc4122#section-4.4)?

Affected Devices/Targets: All toolchains that use make_ext4fs
Revision: make-ext4fs-2020-01-05-5c201be7

30.01.20202783Base systemBug ReportVery LowHighTP-Link Archer A7 v5 can't be flashet via tftpopenwrt-19.07Unconfirmed Task Description

Device: TP-Link Archer A7 (RU) Ver 5.0
Software: OpenWRT 19.07.0

I just bought this router. And I trying to flash it with openwrt-19.07.0-ath79-generic-tplink_archer-a7-v5-squashfs-factory.bin trough tftp.
In wireshark I clearly see that file was downloaded. But router didn’t flashed.
I tried to flash snapshot image wtih same result.
I checked sha256 sums and it matches.

When I reproduced same steps with original TP-Link update image it worked well. Seems like something prevents router from flashing OpenWRT image.

30.01.20202785Base systemBug ReportVery LowHighkernel loading during netboot fails on mikrotik devicesopenwrt-19.07Unconfirmed Task Description

Devices tested:

  • Mikrotik rb433
  • Mikrotik rb435g

Software version: Using the v19.07.1 tag.

Issue: There are a few packages, whose are leading the ramdisk “unbbotable”, more precise the device is not able to load the kernel. First this happened by kmod-scsi-core , I thought it must be some kernel-related issue. Afterthat I realised that either I enable the aforementioned kernel-module, or the libraries called libpcre and libpci, the boot procedure will stop at:

Gateway: 192.168.1.254
transfer started ................................... transfer ok, time=2.61s
setting up elf image... OK
jumping to kernel code OpenWrt kernel loader for AR7XXX/AR9XXX
Copyright (C) 2011 Gabor Juhos juhosg@openwrt.org Decompressing kernel... done!
Starting kernel at 80060000...

Compiling these packages only as a module results a nice bootable image. Firstly I thought that maybe my ramdisk is too large, but it is about only 4,5 MB - previously using older trunk I was able to boot up images over 5 MByte.
I have pasted the config file to the ticket. If you switch libpcre and libpci to M instead of * it will boot.

This issue was not there before, using the image built from 18.06.

31.01.20202791Base systemBug ReportVery LowHighIPv6 router advertisments lost after upgrade to 19.07openwrt-19.07Unconfirmed Task Description

I’ve just upgraded my linksys wrt-1200ac from 18.06.4 to 19.07.0

I’ve got a more-or-less out-of-the-box configuration with wired and wireless clients all connected to the ‘br-lan’ bridge. My ISP provides native IPv6. I’ve got odhcpd-ip6only installed, and a mixture of clients, some using SLAAC and some using DHCPv6.

When a wireless client that is configured for SLAAC (e.g. an android phone) connects, it sends an IPv6 router solicitation to ff02::1 and receives a router advertisement on its fe80::<something> address. That still works fine. But the client never receives any further router adverts, so the route times out after 1800 seconds and IPv6 connectivity is lost.

This is *only* going wrong with wireless clients: tcpdump on a wired client shows router adverts arriving on ff02::1 every few minutes. But tcpdump on a wireless client shows no router adverts after the initial one.

I’ve retested with 18.06.4 and the problem does not exist in that version.

05.02.20202814KernelBug ReportVery LowHighnetns cleanup_net race conditionTrunkUnconfirmed Task Description

I’m seeing this issue on master built for x86-64, it’s been happening since I started using this x86-64 machine around December.

[   73.300163] =============================================================================                                                                                                                                                                                   
[   73.309803] BUG kmalloc-32 (Not tainted): Object already free                                                                                                                                                                                                               
[   73.316694] -----------------------------------------------------------------------------                                                                                                                                                                                   
                                                                                                                                                                                                                                                                               
[   73.328675] Disabling lock debugging due to kernel taint                                                                                                                                                                                                                    
[   73.335167] INFO: Allocated in ops_init+0x6d/0x100 age=147 cpu=0 pid=11053                                                                                                                                                                                                  
[   73.343242] INFO: Freed in 0xffffffffa09c94ca age=36 cpu=2 pid=50                                                                                                                                                                                                           
[   73.350557] INFO: Slab 0x00000000ed33138b objects=36 used=11 fp=0x0000000017541cc8 flags=0xf700000000101                                                                                                                                                                    
[   73.361281] INFO: Object 0x0000000041bc5c4c @offset=1576 fp=0x000000007d23c440                                                                                                                                                                                              
                                                                                                                                                                                                                                                                               
[   73.372490] Redzone 000000008c59cd8b: bb bb bb bb bb bb bb bb                          ........                                                                                                                                                                             
[   73.382449] Object 0000000041bc5c4c: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b  kkkkkkkkkkkkkkkk                                                                                                                                                                      
[   73.393029] Object 0000000073cabfc7: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b a5  kkkkkkkkkkkkkkk.                                                                                                                                                                      
[   73.403599] Redzone 000000009196639c: bb bb bb bb bb bb bb bb                          ........                                                                                                                                                                             
[   73.413574] Padding 000000009337e5e1: 5a 5a 5a 5a 5a 5a 5a 5a                          ZZZZZZZZ                                                                                                                                                                             
[   73.423549] CPU: 2 PID: 50 Comm: kworker/u16:1 Tainted: G    B             4.19.101 #0                                                                                                                                                                                      
[   73.432698] Hardware name: To Be Filled By O.E.M. To Be Filled By O.E.M./Z77 Pro4-M, BIOS P2.10 03/13/2018                                                                                                                                                                  
[   73.443617] Workqueue: netns cleanup_net                                                                                                                                                                                                                                    
[   73.448798] Call Trace:                                                                                                                                                                                                                                                     
[   73.452495]  dump_stack+0x57/0x7a                                                                                                                                                                                                                                           
[   73.457083]  print_trailer+0x203/0x210                                                                                                                                                                                                                                      
[   73.462068]  object_err+0x2f/0x36                                                                                                                                                                                                                                           
[   73.466613]  free_debug_processing.cold.107+0x2c/0x11f                                                                                                                                                                                                                      
[   73.472985]  ? ops_free_list.part.14+0x4d/0x60                                                                                                                                                                                                                              
[   73.478663]  __slab_free+0x1bd/0x330                                                                                                                                                                                                                                        
[   73.483482]  ? kmem_cache_free+0x1b5/0x1e0                                                                                                                                                                                                                                  
[   73.488778]  kfree+0x11c/0x140                                                                                                                                                                                                                                              
[   73.493009]  ops_free_list.part.14+0x4d/0x60                                                                                                                                                                                                                                
[   73.498460]  cleanup_net+0x1c4/0x280                                                                                                                                                                                                                                        
[   73.503215]  process_one_work+0x1a8/0x340                                                                                                                                                                                                                                   
[   73.508384]  worker_thread+0x2f/0x3a0                                                                                                                                                                                                                                       
[   73.513215]  kthread+0x10b/0x130                                                                                                                                                                                                                                            
[   73.517619]  ? process_one_work+0x340/0x340                                                                                                                                                                                                                                 
[   73.522967]  ? kthread_create_worker_on_cpu+0x60/0x60                                                                                                                                                                                                                       
[   73.529193]  ret_from_fork+0x35/0x40                                                                                                                                                                                                                                        
[   73.534067] FIX kmalloc-32: Object at 0x0000000041bc5c4c not freed                                                                                                                                                                                                          

There are old closed reports about it 2353 2354

I have tried with kernel 4.14 and with kernel 4.19 from the 19 branch and also removing the nf_conntrack_rtcache module, but the result is the same.

There are times that I see no BUG at all, others where I see it appear between 1 and several times. I use several docker containers and depending on the races, sometimes everything launches well and afterwards (if I don’t play with new docker instances) it is 100% stable whereas other times I have to reboot up to 3 or even 5 times for everything to work reliably.

dmesg with some race but working stable

partial dmesg which ends crashing, captured from another machine

16.02.20202835Base systemBug ReportVery LowHighMT7621: Clients disconnects.openwrt-19.07Unconfirmed Task Description

Hi! I have MT7621 and when to router connected more than 10 peoples router start disconnecting some peoples(have two networks guest and main on 2,4).

There is my settings:
config wifi-iface ‘default_radio0’ option device ‘radio0’ option network ‘lan’ option mode ‘ap’ option wpa_disable_eapol_key_retries ‘1’ option key ‘WIFIPASS’ option ssid ‘WIFINAME’ option encryption ‘psk2+ccmp’ option disassoc_low_ack ‘0’ (guest network have same settings)

Other info:
Newifi-D2
MediaTek MT7621 ver:1 eco:3
OpenWrt 19.07.1 r10911-c155900f66 / LuCI openwrt-19.07 branch git-20.045.27998-49999e9

I also noticed that before the client is disconnected from the network, it will lose the Internet.

 

Issue on github: https://github.com/openwrt/mt76/issues/358

Many peoples with Newifi3 D2 have same problem(in github links and more details).

PLEASE, FIX IT!

18.02.20202844Base systemBug ReportVery LowHighath10k on archer C7 v2: high latencyopenwrt-19.07Unconfirmed Task Description

On my Archer C7 v2, since the upgrade from 18.06 to 19.07, I sometimes get very high latency on my 5 GHz wifi network:

This is when pinging a wireless client from the router itself.

ping 192.168.12.167
PING 192.168.12.167 (192.168.12.167): 56 data bytes
64 bytes from 192.168.12.167: seq=0 ttl=64 time=1.334 ms
64 bytes from 192.168.12.167: seq=1 ttl=64 time=2.002 ms
64 bytes from 192.168.12.167: seq=2 ttl=64 time=1004.448 ms
64 bytes from 192.168.12.167: seq=3 ttl=64 time=4.342 ms
64 bytes from 192.168.12.167: seq=4 ttl=64 time=1.072 ms
64 bytes from 192.168.12.167: seq=5 ttl=64 time=2.074 ms
64 bytes from 192.168.12.167: seq=6 ttl=64 time=2.505 ms
64 bytes from 192.168.12.167: seq=7 ttl=64 time=1.059 ms
64 bytes from 192.168.12.167: seq=8 ttl=64 time=1.746 ms
64 bytes from 192.168.12.167: seq=9 ttl=64 time=1.176 ms
64 bytes from 192.168.12.167: seq=10 ttl=64 time=1.086 ms
64 bytes from 192.168.12.167: seq=11 ttl=64 time=1.072 ms
64 bytes from 192.168.12.167: seq=12 ttl=64 time=815.290 ms
64 bytes from 192.168.12.167: seq=13 ttl=64 time=1004.417 ms
64 bytes from 192.168.12.167: seq=14 ttl=64 time=4.294 ms
64 bytes from 192.168.12.167: seq=15 ttl=64 time=4.520 ms
64 bytes from 192.168.12.167: seq=16 ttl=64 time=1003.250 ms
64 bytes from 192.168.12.167: seq=17 ttl=64 time=3.125 ms
64 bytes from 192.168.12.167: seq=18 ttl=64 time=1.019 ms
64 bytes from 192.168.12.167: seq=19 ttl=64 time=2.066 ms
^C
--- 192.168.12.167 ping statistics ---
20 packets transmitted, 20 packets received, 0% packet loss
round-trip min/avg/max = 1.019/193.094/1004.448 ms

The upgrade to 19.07.1 didn’t solve the issue. What (temporarily) seem to work is to restart the wlan0 interface. After a few hours the problem comes back. The client is very close to the AP (less than 3 meters, although there is a floor between). Signal quality is reported as very good.

Station 54:60:09:d3:e4:d6 (on wlan0)
        inactive time:  540 ms
        rx bytes:       1082546
        rx packets:     6294
        tx bytes:       15523400
        tx packets:     11636
        tx retries:     0
        tx failed:      1
        rx drop misc:   0
        signal:         -66 [-76, -68, -71] dBm
        signal avg:     -62 [-72, -64, -67] dBm
        tx bitrate:     390.0 MBit/s VHT-MCS 8 80MHz short GI VHT-NSS 1
        rx bitrate:     390.0 MBit/s VHT-MCS 8 80MHz short GI VHT-NSS 1
        rx duration:    422088 us
        last ack signal:-95 dBm
        authorized:     yes
        authenticated:  yes
        associated:     yes
        preamble:       long
        WMM/WME:        yes
        MFP:            no
        TDLS peer:      no
        DTIM period:    2
        beacon interval:100
        short slot time:yes
        connected time: 447 seconds

I am using stock 19.07.1 firmware. I also tried changing the regulatory domain from CA to US but it didn’t help.
I will now try with the non-ct driver and firmware to see if it helps, as it worked fine on 18.06 which didn’t include the -ct firmware by default.

cat /etc/config/wireless

config wifi-device 'radio0'
        option type 'mac80211'
        option hwmode '11a'
        option path 'pci0000:00/0000:00:00.0'
        option htmode 'VHT80'
        option noscan '1'
        option country 'US'
        option channel '149'

config wifi-iface 'default_radio0'
        option device 'radio0'
        option key 'removed'
        option network 'lan'
        option mode 'ap'
        option ssid 'myssid5'
        option encryption 'psk2+ccmp'

config wifi-device 'radio1'
        option type 'mac80211'
        option channel '11'
        option hwmode '11g'
        option path 'platform/ahb/ahb:apb/18100000.wmac'
        option noscan '1'
#       option country 'CA'
        option htmode 'HT40'
        option require_mode 'g'

config wifi-iface 'default_radio1'
        option device 'radio1'
        option network 'lan'
        option mode 'ap'
        option ssid 'myssid'
        option encryption 'psk2+ccmp'
        option key 'removed'
        option ieee80211w '1'
21.02.20202847Base systemBug ReportVery LowHighbetween ath79-master-r12157-a1cfe0dcbb and ath79-master...TrunkUnconfirmed Task Description

Supply the following if possible:
- Device problem occurs on
Netgear WNDR3700v2

- Software versions of OpenWrt/LEDE release, packages, etc.

between ath79-master-r12157-a1cfe0dcbb and ath79-master-r12259 including the rename from wndr3700v2 to wndr3700-v2 OpenWrt lost its capability to detect the two radios.

- Steps to reproduce

 


root@router:/tmp# cat /etc/banner

_______                     ________        __

| |.—–.—–.—–.| | | |.—-.| |_
| - || _ | -| || | | || _|| _|
|
_|| |_||||||| ||

        |__| W I R E L E S S   F R E E D O M

—————————————————– OpenWrt SNAPSHOT, r12157-a1cfe0dcbb


root@router:/tmp# dmesg
[ 0.000000] Linux version 4.19.98 (moeller@work-horse) (gcc version 8.3.0 (OpenWrt GCC 8.3.0 r12053-9e799f3eee)) #0 Fri Jan 31 22:29:40 2020
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
[ 0.000000] MIPS: machine is Netgear WNDR3700v2
[ 0.000000] SoC: Atheros AR7161 rev 2
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0×0000000000000000-0x0000000003ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0×0000000000000000-0x0000000003ffffff]
[ 0.000000] Initmem setup node 0 [mem 0×0000000000000000-0x0000000003ffffff]
[ 0.000000] On node 0 totalpages: 16384
[ 0.000000] Normal zone: 144 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 16384 pages, LIFO batch:3
[ 0.000000] random: get_random_bytes called from start_kernel+0×98/0x4a8 with crng_init=0
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16240
[ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 57516K/65536K available (4327K kernel code, 176K rwdata, 1020K rodata, 1188K init, 206K bss, 8020K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 51
[ 0.000000] CPU clock: 680.000 MHz [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 5621354254 ns
[ 0.000008] sched_clock: 32 bits at 340MHz, resolution 2ns, wraps every 6316128254ns
[ 0.007800] Calibrating delay loop... 452.19 BogoMIPS (lpj=2260992)
[ 0.074071] pid_max: default: 32768 minimum: 301
[ 0.078916] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.085519] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.096880] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.106751] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.112960] pinctrl core: initialized pinctrl subsystem
[ 0.119019] NET: Registered protocol family 16
[ 0.428745] PCI host bridge /ahb/apb/pcie-controller@17010000 ranges:
[ 0.435198] MEM 0×0000000010000000..0x0000000016ffffff
[ 0.440426] IO 0×0000000000000000..0×0000000000000000 [ 0.463018] PCI host bridge to bus 0000:00
[ 0.467126] pci_bus 0000:00: root bus resource [mem 0×10000000-0x16ffffff]
[ 0.474044] pci_bus 0000:00: root bus resource [io 0×0000]
[ 0.479604] pci_bus 0000:00: root bus resource [??? 0×00000000 flags 0×0]
[ 0.486385] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.494769] pci 0000:00:11.0: [168c:ff1d] type 00 class 0×020000 [ 0.494800] pci 0000:00:11.0: reg 0×10: [mem 0×00000000-0x0000ffff]
[ 0.495095] pci 0000:00:12.0: [168c:ff1d] type 00 class 0×020000 [ 0.495122] pci 0000:00:12.0: reg 0×10: [mem 0×00000000-0x0000ffff]
[ 0.495679] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 0.495708] pci 0000:00:11.0: BAR 0: assigned [mem 0×10000000-0x1000ffff]
[ 0.502528] pci 0000:00:12.0: BAR 0: assigned [mem 0×10010000-0x1001ffff]
[ 0.512297] clocksource: Switched to clocksource MIPS
[ 0.518346] NET: Registered protocol family 2
[ 0.523491] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes)
[ 0.531183] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.538204] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.544573] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.551058] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.556944] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.563492] NET: Registered protocol family 1
[ 0.567890] PCI: CLS 0 bytes, default 32
[ 0.570473] Crashlog allocated RAM at address 0x3f00000
[ 0.576987] workingset: timestamp_bits=14 max_order=14 bucket_order=0
[ 0.589206] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.595083] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) © 2001-2006 Red Hat, Inc.
[ 0.615469] io scheduler noop registered
[ 0.619388] io scheduler deadline registered (default)
[ 0.625206] ar7100-usb-phy 18030000.usb-phy: phy reset is missing
[ 0.632106] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.639111] console [ttyS0] disabled
[ 0.642766] 18020000.uart: ttyS0 at MMIO 0×18020000 (irq = 10, base_baud = 10625000) is a 16550A
[ 0.651550] console [ttyS0] enabled
[ 0.658520] bootconsole [early0] disabled
[ 0.672685] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
[ 0.677766] 4 fixed-partitions partitions found on MTD device spi0.0
[ 0.684156] Creating 4 MTD partitions on “spi0.0”:
[ 0.688944] 0×000000000000-0×000000050000 : “u-boot” [ 0.694662] 0×000000050000-0×000000070000 : “u-boot-env” [ 0.700642] 0×000000070000-0x000000ff0000 : “firmware” [ 0.709051] 2 netgear-fw partitions found on MTD device firmware
[ 0.715111] Creating 2 MTD partitions on “firmware”:
[ 0.720073] 0×000000000000-0x0000001c4440 : “kernel” [ 0.725799] 0x0000001c4440-0x000000f80000 : “rootfs” [ 0.731378] mtd: device 4 (rootfs) set to be root filesystem
[ 0.738413] 1 squashfs-split partitions found on MTD device rootfs
[ 0.744648] 0x0000007b0000-0x000000f80000 : “rootfs_data” [ 0.750780] 0x000000ff0000-0×000001000000 : “art” [ 0.756658] Realtek RTL8366S ethernet switch driver version 0.2.2
[ 0.762862] rtl8366s rtl8366s: cannot find mdio node phandle
[ 0.768528] rtl8366s rtl8366s: using GPIO pins 5 (SDA) and 7 (SCK)
[ 0.774813] rtl8366s rtl8366s: RTL8366 ver. 1 chip found
[ 0.826529] libphy: rtl8366s: probed
[ 0.831545] libphy: Fixed MDIO Bus: probed
[ 1.184018] ag71xx 19000000.eth: connected to PHY at fixed-0:00 [uid=00000000, driver=Generic PHY]
[ 1.193617] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode: rgmii
[ 1.533893] ag71xx 1a000000.eth: connected to PHY at rtl8366s:04 [uid=001cc960, driver=Generic PHY]
[ 1.543585] eth1: Atheros AG71xx at 0xba000000, irq 5, mode: rgmii
[ 1.552067] NET: Registered protocol family 10
[ 1.561269] Segment Routing with IPv6
[ 1.565090] NET: Registered protocol family 17
[ 1.569586] 8021q: 802.1Q VLAN Support v1.8
[ 1.585516] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[ 1.596158] Freeing unused kernel memory: 1188K
[ 1.600682] This architecture does not have kernel memory protection.
[ 1.607138] Run /sbin/init as init process
[ 2.582308] random: fast init done
[ 2.807119] init: Console is alive
[ 2.810741] init: - watchdog -
[ 6.241610] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 6.383455] usbcore: registered new interface driver usbfs
[ 6.389022] usbcore: registered new interface driver hub
[ 6.394453] usbcore: registered new device driver usb
[ 6.430284] ehci_hcd: USB 2.0 ‘Enhanced’ Host Controller (EHCI) Driver
[ 6.445010] SCSI subsystem initialized
[ 6.453749] ehci-platform: EHCI generic platform driver
[ 7.058167] ehci-platform 1b000000.usb: EHCI Host Controller
[ 7.063869] ehci-platform 1b000000.usb: new USB bus registered, assigned bus number 1
[ 7.071783] ehci-platform 1b000000.usb: irq 3, io mem 0x1b000000
[ 7.102319] ehci-platform 1b000000.usb: USB 2.0 started, EHCI 1.00
[ 7.109300] hub 1-0:1.0: USB hub found
[ 7.113454] hub 1-0:1.0: 2 ports detected
[ 7.120810] ohci_hcd: USB 1.1 ‘Open’ Host Controller (OHCI) Driver
[ 7.128705] ohci-platform: OHCI generic platform driver
[ 7.134182] ohci-platform 1c000000.usb: Generic Platform OHCI controller
[ 7.140911] ohci-platform 1c000000.usb: new USB bus registered, assigned bus number 2
[ 7.148855] ohci-platform 1c000000.usb: irq 14, io mem 0x1c000000
[ 7.227154] hub 2-0:1.0: USB hub found
[ 7.231244] hub 2-0:1.0: 2 ports detected
[ 7.239911] usbcore: registered new interface driver usb-storage
[ 7.246968] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 7.257068] init: - preinit -
[ 7.952485] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 8.224006] usb-storage 1-1:1.0: USB Mass Storage device detected
[ 8.239044] scsi host0: usb-storage 1-1:1.0
[ 8.607425] random: procd: uninitialized urandom read (4 bytes read)
[ 9.217736] random: jshn: uninitialized urandom read (4 bytes read)
[ 9.313323] scsi 0:0:0:0: Direct-Access SanDisk Ultra 1.01 PQ: 0 ANSI: 2
[ 9.324268] sd 0:0:0:0: [sda] 31266816 512-byte logical blocks: (16.0 GB/14.9 GiB)
[ 9.435234] sd 0:0:0:0: [sda] Write Protect is off
[ 9.440027] sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00
[ 9.441159] sd 0:0:0:0: [sda] No Caching mode page found
[ 9.446536] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 9.467635] sda: sda1 sda2
[ 9.485172] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 9.512732] random: jshn: uninitialized urandom read (4 bytes read)
[ 9.803851] random: jshn: uninitialized urandom read (4 bytes read)
[ 9.855143] random: jshn: uninitialized urandom read (4 bytes read)
[ 9.937787] random: jshn: uninitialized urandom read (4 bytes read)
[ 10.734464] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 11.792658] eth0: link up (1000Mbps/Full duplex)
[ 11.797336] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 21.002121] mount_root: loading kmods from internal overlay
[ 21.065763] kmodloader: loading kernel modules from etc/modules-boot.d/*
[ 21.074086] kmodloader: done loading kernel modules from
etc/modules-boot.d/*
[ 22.067245] jffs2: notice: (573) jffs2_build_xattr_subsystem: complete building xattr subsystem, 4 of xdatum (3 unchecked, 1 orphan) and 38 of xref (1 dead, 0 orphan) found.
[ 22.083539] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 22.104478] block: extroot: not configured
[ 22.493615] jffs2: notice: (571) jffs2_build_xattr_subsystem: complete building xattr subsystem, 4 of xdatum (3 unchecked, 1 orphan) and 38 of xref (1 dead, 0 orphan) found.
[ 22.512972] mount_root: loading kmods from internal overlay
[ 22.571532] kmodloader: loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
[ 22.586940] kmodloader: done loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
[ 23.297496] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 23.311711] block: extroot: not configured
[ 23.317033] mount_root: switching to jffs2 overlay
[ 23.391179] overlayfs: upper fs does not support tmpfile.
[ 23.402971] urandom-seed: Seeding with /etc/urandom.seed
[ 23.506382] eth0: link down
[ 23.522968] procd: - early -
[ 23.525956] procd: - watchdog -
[ 24.224357] procd: - watchdog -
[ 24.227866] procd: - ubus -
[ 24.305816] urandom_read: 2 callbacks suppressed
[ 24.305823] random: ubusd: uninitialized urandom read (4 bytes read)
[ 24.321238] random: ubusd: uninitialized urandom read (4 bytes read)
[ 24.330097] procd: - init -
[ 25.653767] kmodloader: loading kernel modules from /etc/modules.d/*
[ 25.815614] ntfs: driver 2.1.32 [Flags: R/O MODULE].
[ 25.855111] tun: Universal TUN/TAP device driver, 1.6
[ 25.878662] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 25.922686] gre: GRE over IPv4 demultiplexor driver
[ 25.944224] ip_gre: GRE over IPv4 tunneling driver
[ 26.291706] Mirror/redirect action on
[ 26.325462] u32 classifier
[ 26.328171] input device check on
[ 26.331822] Actions configured
[ 26.380723] Loading modules backported from Linux version v5.4-rc8-0-gaf42d3466bdc
[ 26.388336] Backport generated by backports.git v5.4-rc8-1-0-g368e8c51
[ 26.401462] urngd: v1.0.2 started.
[ 26.492389] usbcore: registered new interface driver usbserial_generic
[ 26.498978] usbserial: USB Serial support registered for generic
[ 26.558787] wireguard: WireGuard 0.0.20200128 loaded. See www.wireguard.com for information.
[ 26.567273] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld Jason@zx2c4.com. All Rights Reserved.
[ 26.778103] xt_time: kernel timezone is -0000
[ 26.798642] ath9k_pci_owl_loader 0000:00:11.0: enabling device (0000 → 0002)
[ 26.806040] ath9k_pci_owl_loader 0000:00:12.0: enabling device (0000 → 0002)
[ 26.824088] ath9k_pci_owl_loader 0000:00:12.0: fixup device configuration
[ 26.832789] ath9k_pci_owl_loader 0000:00:11.0: fixup device configuration
[ 26.861449] pci 0000:00:12.0: [168c:0029] type 00 class 0×028000 [ 26.861487] pci 0000:00:12.0: reg 0×10: [mem 0×10010000-0x1001ffff]
[ 26.861542] pci 0000:00:12.0: PME# supported from D0 D3hot
[ 26.862141] pci 0000:00:12.0: BAR 0: assigned [mem 0×10010000-0x1001ffff]
[ 26.877545] pci 0000:00:11.0: [168c:0029] type 00 class 0×028000 [ 26.877582] pci 0000:00:11.0: reg 0×10: [mem 0×10000000-0x1000ffff]
[ 26.877638] pci 0000:00:11.0: PME# supported from D0 D3hot
[ 26.878247] pci 0000:00:11.0: BAR 0: assigned [mem 0×10000000-0x1000ffff]
[ 27.066477] random: crng init done
[ 27.156340] PPP generic driver version 2.4.2
[ 27.183974] PPP MPPE Compression module registered
[ 27.199611] NET: Registered protocol family 24
[ 27.218213] PPTP driver version 0.8.5
[ 27.368426] ath9k 0000:00:12.0: enabling device (0000 → 0002)
[ 27.408317] ath: phy0: Ignoring endianness difference in EEPROM magic bytes.
[ 27.416965] ath: EEPROM regdomain: 0×0 [ 27.416971] ath: EEPROM indicates default country code should be used
[ 27.416974] ath: doing EEPROM country→regdmn map search
[ 27.416984] ath: country maps to regdmn code: 0x3a
[ 27.416989] ath: Country alpha2 being used: US
[ 27.416992] ath: Regpair used: 0x3a
[ 27.433820] ieee80211 phy0: Selected rate control algorithm ‘minstrel_ht’ [ 27.435348] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xb0010000, irq=19
[ 27.442114] ath9k 0000:00:11.0: enabling device (0000 → 0002)
[ 27.584297] ath: phy1: Ignoring endianness difference in EEPROM magic bytes.
[ 27.592914] ath: EEPROM regdomain: 0×0 [ 27.592920] ath: EEPROM indicates default country code should be used
[ 27.592923] ath: doing EEPROM country→regdmn map search
[ 27.592933] ath: country maps to regdmn code: 0x3a
[ 27.592938] ath: Country alpha2 being used: US
[ 27.592940] ath: Regpair used: 0x3a
[ 27.607441] ieee80211 phy1: Selected rate control algorithm ‘minstrel_ht’ [ 27.608985] ieee80211 phy1: Atheros AR9280 Rev:2 mem=0xb0000000, irq=18
[ 27.702755] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 44.364371] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts:
[ 44.414576] Adding 976560k swap on /dev/sda1. Priority:-2 extents:1 across:976560k
[ 48.643400] eth0: link up (1000Mbps/Full duplex)
[ 48.648969] br-lan: port 1(eth0) entered blocking state
[ 48.654275] br-lan: port 1(eth0) entered disabled state
[ 48.659807] device eth0 entered promiscuous mode
[ 48.692372] br-lan: port 1(eth0) entered blocking state
[ 48.697596] br-lan: port 1(eth0) entered forwarding state
[ 48.703176] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 48.790578] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 48.835679] IPv6: ADDRCONF(NETDEV_UP): eth1.2: link is not ready
[ 48.951180] IPv6: ADDRCONF(NETDEV_UP): eth1.7: link is not ready
[ 49.712398] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 51.437743] eth1: link up (1000Mbps/Full duplex)
[ 51.513573] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 51.582425] IPv6: ADDRCONF(NETDEV_CHANGE): eth1.2: link becomes ready
[ 51.589118] IPv6: ADDRCONF(NETDEV_CHANGE): eth1.7: link becomes ready
[ 54.282504] ath: EEPROM regdomain: 0×8114 [ 54.286516] ath: EEPROM indicates we should expect a country code
[ 54.292634] ath: doing EEPROM country→regdmn map search
[ 54.297928] ath: country maps to regdmn code: 0×37 [ 54.302722] ath: Country alpha2 being used: DE
[ 54.307157] ath: Regpair used: 0×37 [ 54.310630] ath: regdomain 0×8114 dynamically updated by user
[ 54.316523] ath: EEPROM regdomain: 0×8114 [ 54.320516] ath: EEPROM indicates we should expect a country code
[ 54.326609] ath: doing EEPROM country→regdmn map search
[ 54.331904] ath: country maps to regdmn code: 0×37 [ 54.336698] ath: Country alpha2 being used: DE
[ 54.341125] ath: Regpair used: 0×37 [ 54.344620] ath: regdomain 0×8114 dynamically updated by user
[ 54.836482] pppoe-wan: renamed from ppp0
[ 57.427192] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 57.492852] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 57.616731] br-lan: port 2(wlan0) entered blocking state
[ 57.622045] br-lan: port 2(wlan0) entered disabled state
[ 57.627773] device wlan0 entered promiscuous mode
[ 57.632654] br-lan: port 2(wlan0) entered blocking state
[ 57.637986] br-lan: port 2(wlan0) entered forwarding state
[ 57.693619] br-lan: port 3(wlan1) entered blocking state
[ 57.698935] br-lan: port 3(wlan1) entered disabled state
[ 57.704667] device wlan1 entered promiscuous mode
[ 58.525536] br-lan: port 2(wlan0) entered disabled state
[ 58.531209] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 58.537780] br-lan: port 3(wlan1) entered blocking state
[ 58.543145] br-lan: port 3(wlan1) entered forwarding state
[ 58.750884] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 58.757483] br-lan: port 2(wlan0) entered blocking state
[ 58.762856] br-lan: port 2(wlan0) entered forwarding state
[84181.737818] pppoe-wan: renamed from ppp0
[144550.658055] pppoe-wan: renamed from ppp0
[159913.299297] eth1: link down
[159918.352853] IPv6: ADDRCONF(NETDEV_UP): eth1.7: link is not ready
[159919.249344] eth1: link up (1000Mbps/Full duplex)
[159919.251734] IPv6: ADDRCONF(NETDEV_CHANGE): eth1.7: link becomes ready
[159923.807531] eth1: link down
[159924.830488] eth1: link up (1000Mbps/Full duplex)
[159931.219728] eth1: link down
[159936.244722] IPv6: ADDRCONF(NETDEV_UP): eth1.7: link is not ready
[159950.979373] eth1: link up (1000Mbps/Full duplex)
[159950.982129] IPv6: ADDRCONF(NETDEV_CHANGE): eth1.7: link becomes ready
[160110.252218] pppoe-wan: renamed from ppp0
[246512.671046] pppoe-wan: renamed from ppp0
[260793.131776] pppoe-wan: renamed from ppp0
[347195.313169] pppoe-wan: renamed from ppp0
[433596.980231] pppoe-wan: renamed from ppp0
[449177.428433] pppoe-wan: renamed from ppp0
[535580.336441] pppoe-wan: renamed from ppp0
root@router:~#

BusyBox v1.31.1 () built-in shell (ash)

_______                     ________        __

| |.—–.—–.—–.| | | |.—-.| |_
| - || _ | -| || | | || _|| _|
|
_|| |_||||||| ||

        |__| W I R E L E S S   F R E E D O M

—————————————————– OpenWrt SNAPSHOT, r12259-2f1cc5c3d5


root@router:~# dmesg
[ 0.000000] Linux version 4.19.101 (moeller@work-horse) (gcc version 8.3.0 (OpenWrt GCC 8.3.0 r12053-9e799f3eee)) #0 Tue Feb 18 15:10:31 2020
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
[ 0.000000] MIPS: machine is Netgear WNDR3700 v2
[ 0.000000] SoC: Atheros AR7161 rev 2
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0×0000000000000000-0x0000000003ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0×0000000000000000-0x0000000003ffffff]
[ 0.000000] Initmem setup node 0 [mem 0×0000000000000000-0x0000000003ffffff]
[ 0.000000] On node 0 totalpages: 16384
[ 0.000000] Normal zone: 144 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 16384 pages, LIFO batch:3
[ 0.000000] random: get_random_bytes called from start_kernel+0×98/0x4a8 with crng_init=0
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16240
[ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 57452K/65536K available (4336K kernel code, 180K rwdata, 1020K rodata, 1240K init, 206K bss, 8084K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 51
[ 0.000000] CPU clock: 680.000 MHz [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 5621354254 ns
[ 0.000008] sched_clock: 32 bits at 340MHz, resolution 2ns, wraps every 6316128254ns
[ 0.007802] Calibrating delay loop... 452.19 BogoMIPS (lpj=2260992)
[ 0.074072] pid_max: default: 32768 minimum: 301
[ 0.078916] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.085519] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.096900] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.106767] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.112979] pinctrl core: initialized pinctrl subsystem
[ 0.119049] NET: Registered protocol family 16
[ 0.428873] PCI host bridge /ahb/apb/pcie-controller@17010000 ranges:
[ 0.435329] MEM 0×0000000010000000..0x0000000016ffffff
[ 0.440561] IO 0×0000000000000000..0×0000000000000000 [ 0.463724] PCI host bridge to bus 0000:00
[ 0.467827] pci_bus 0000:00: root bus resource [mem 0×10000000-0x16ffffff]
[ 0.474747] pci_bus 0000:00: root bus resource [io 0×0000]
[ 0.480307] pci_bus 0000:00: root bus resource [??? 0×00000000 flags 0×0]
[ 0.487093] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.495479] pci 0000:00:11.0: [168c:ff1d] type 00 class 0×020000 [ 0.495512] pci 0000:00:11.0: reg 0×10: [mem 0×00000000-0x0000ffff]
[ 0.495815] pci 0000:00:12.0: [168c:ff1d] type 00 class 0×020000 [ 0.495841] pci 0000:00:12.0: reg 0×10: [mem 0×00000000-0x0000ffff]
[ 0.496401] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 0.496430] pci 0000:00:11.0: BAR 0: assigned [mem 0×10000000-0x1000ffff]
[ 0.503258] pci 0000:00:12.0: BAR 0: assigned [mem 0×10010000-0x1001ffff]
[ 0.513082] clocksource: Switched to clocksource MIPS
[ 0.519172] NET: Registered protocol family 2
[ 0.524330] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes)
[ 0.532014] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.539035] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.545408] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.551886] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.557771] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.564323] NET: Registered protocol family 1
[ 0.568729] PCI: CLS 0 bytes, default 32
[ 0.571378] Crashlog allocated RAM at address 0x3f00000
[ 0.577915] workingset: timestamp_bits=14 max_order=14 bucket_order=0
[ 0.590375] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.596252] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) © 2001-2006 Red Hat, Inc.
[ 0.616936] io scheduler noop registered
[ 0.620852] io scheduler deadline registered (default)
[ 0.626692] ar7100-usb-phy 18030000.usb-phy: phy reset is missing
[ 0.633681] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.640613] console [ttyS0] disabled
[ 0.644274] 18020000.uart: ttyS0 at MMIO 0×18020000 (irq = 10, base_baud = 10625000) is a 16550A
[ 0.653058] console [ttyS0] enabled
[ 0.660028] bootconsole [early0] disabled
[ 0.674536] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
[ 0.679618] 4 fixed-partitions partitions found on MTD device spi0.0
[ 0.686021] Creating 4 MTD partitions on “spi0.0”:
[ 0.690808] 0×000000000000-0×000000050000 : “u-boot” [ 0.696550] 0×000000050000-0×000000070000 : “u-boot-env” [ 0.702548] 0×000000070000-0x000000ff0000 : “firmware” [ 0.711065] 2 netgear-fw partitions found on MTD device firmware
[ 0.717127] Creating 2 MTD partitions on “firmware”:
[ 0.722090] 0×000000000000-0x0000001c5440 : “kernel” [ 0.727837] 0x0000001c5440-0x000000f80000 : “rootfs” [ 0.733518] mtd: device 4 (rootfs) set to be root filesystem
[ 0.740540] 1 squashfs-split partitions found on MTD device rootfs
[ 0.746771] 0x0000007e0000-0x000000f80000 : “rootfs_data” [ 0.752926] 0x000000ff0000-0×000001000000 : “art” [ 0.758843] Realtek RTL8366S ethernet switch driver version 0.2.2
[ 0.765052] rtl8366s rtl8366s: cannot find mdio node phandle
[ 0.770719] rtl8366s rtl8366s: using GPIO pins 5 (SDA) and 7 (SCK)
[ 0.777005] rtl8366s rtl8366s: RTL8366 ver. 1 chip found
[ 0.827344] libphy: rtl8366s: probed
[ 0.833038] libphy: Fixed MDIO Bus: probed
[ 1.184827] ag71xx 19000000.eth: connected to PHY at fixed-0:00 [uid=00000000, driver=Generic PHY]
[ 1.194429] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode: rgmii
[ 1.534679] ag71xx 1a000000.eth: connected to PHY at rtl8366s:04 [uid=001cc960, driver=Generic PHY]
[ 1.544386] eth1: Atheros AG71xx at 0xba000000, irq 5, mode: rgmii
[ 1.552885] NET: Registered protocol family 10
[ 1.562197] Segment Routing with IPv6
[ 1.566017] NET: Registered protocol family 17
[ 1.570511] 8021q: 802.1Q VLAN Support v1.8
[ 1.587431] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[ 1.598222] Freeing unused kernel memory: 1240K
[ 1.602744] This architecture does not have kernel memory protection.
[ 1.609207] Run /sbin/init as init process
[ 2.583093] random: fast init done
[ 2.802168] init: Console is alive
[ 2.805875] init: - watchdog -
[ 6.090295] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 6.231212] usbcore: registered new interface driver usbfs
[ 6.236831] usbcore: registered new interface driver hub
[ 6.242219] usbcore: registered new device driver usb
[ 6.281739] SCSI subsystem initialized
[ 6.292568] usbcore: registered new interface driver usb-storage
[ 6.299577] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 6.309264] init: - preinit -
[ 8.224350] random: jshn: uninitialized urandom read (4 bytes read)
[ 8.466243] random: jshn: uninitialized urandom read (4 bytes read)
[ 8.754611] random: jshn: uninitialized urandom read (4 bytes read)
[ 9.618495] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 9.752825] urandom_read: 4 callbacks suppressed
[ 9.752833] random: procd: uninitialized urandom read (4 bytes read)
[ 10.673421] eth0: link up (1000Mbps/Full duplex)
[ 10.678056] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 20.006729] mount_root: loading kmods from internal overlay
[ 20.070104] kmodloader: loading kernel modules from etc/modules-boot.d/*
[ 20.078087] kmodloader: done loading kernel modules from
etc/modules-boot.d/*
[ 20.858277] jffs2_scan_eraseblock(): End of filesystem marker found at 0×30000 [ 20.865541] jffs2_build_filesystem(): unlocking the mtd device...
[ 20.865544] done.
[ 20.873637] jffs2_build_filesystem(): erasing all blocks after the end marker...
[ 78.939877] done.
[ 78.949323] jffs2: notice: (558) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 78.965200] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 78.972247] block: unable to load configuration (fstab: Entry not found)
[ 78.979108] block: attempting to load /tmp/jffs_cfg/etc/config/fstab
[ 78.985665] block: unable to load configuration (fstab: Entry not found)
[ 78.992448] block: attempting to load /etc/config/fstab
[ 79.062790] block: extroot: not configured
[ 79.566994] jffs2: notice: (556) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 80.268686] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 80.275845] block: unable to load configuration (fstab: Entry not found)
[ 80.282637] block: attempting to load /tmp/jffs_cfg/etc/config/fstab
[ 80.289201] block: unable to load configuration (fstab: Entry not found)
[ 80.296055] block: attempting to load /etc/config/fstab
[ 80.301752] block: extroot: not configured
[ 80.307978] mount_root: overlay filesystem has not been fully initialized yet
[ 80.321266] mount_root: switching to jffs2 overlay
[ 80.389579] overlayfs: upper fs does not support tmpfile.
[ 83.093791] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 83.182093] eth0: link down
[ 83.196988] procd: - early -
[ 83.199968] procd: - watchdog -
[ 83.834517] procd: - watchdog -
[ 83.837950] procd: - ubus -
[ 83.904783] random: ubusd: uninitialized urandom read (4 bytes read)
[ 83.912132] random: ubusd: uninitialized urandom read (4 bytes read)
[ 83.919702] procd: - init -
[ 84.893323] kmodloader: loading kernel modules from /etc/modules.d/*
[ 85.045275] tun: Universal TUN/TAP device driver, 1.6
[ 85.069431] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 85.119219] gre: GRE over IPv4 demultiplexor driver
[ 85.139270] ip_gre: GRE over IPv4 tunneling driver
[ 85.484432] Mirror/redirect action on
[ 85.511393] u32 classifier
[ 85.514167] input device check on
[ 85.517816] Actions configured
[ 85.563375] Loading modules backported from Linux version v5.4-rc8-0-gaf42d3466bdc
[ 85.570932] Backport generated by backports.git v5.4-rc8-1-0-g368e8c51
[ 85.594056] urngd: v1.0.2 started.
[ 85.779351] usbcore: registered new interface driver usbserial_generic
[ 85.786017] usbserial: USB Serial support registered for generic
[ 85.834097] wireguard: WireGuard 0.0.20200215 loaded. See www.wireguard.com for information.
[ 85.842525] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld Jason@zx2c4.com. All Rights Reserved.
[ 86.062495] xt_time: kernel timezone is -0000
[ 86.197742] random: crng init done
[ 86.337283] PPP generic driver version 2.4.2
[ 86.361591] PPP MPPE Compression module registered
[ 86.378734] NET: Registered protocol family 24
[ 86.408191] PPTP driver version 0.8.5
[ 86.566705] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 104.504191] eth0: link up (1000Mbps/Full duplex)
[ 104.509789] br-lan: port 1(eth0) entered blocking state
[ 104.515094] br-lan: port 1(eth0) entered disabled state
[ 104.520630] device eth0 entered promiscuous mode
[ 104.604615] br-lan: port 1(eth0) entered blocking state
[ 104.609845] br-lan: port 1(eth0) entered forwarding state
[ 104.615450] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 104.663301] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 104.708562] IPv6: ADDRCONF(NETDEV_UP): eth1.2: link is not ready
[ 104.808242] IPv6: ADDRCONF(NETDEV_UP): eth1.7: link is not ready
[ 105.553190] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 106.773996] eth1: link up (1000Mbps/Full duplex)
[ 106.851719] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 106.911421] IPv6: ADDRCONF(NETDEV_CHANGE): eth1.2: link becomes ready
[ 106.918175] IPv6: ADDRCONF(NETDEV_CHANGE): eth1.7: link becomes ready
[ 108.903192] pppoe-wan: renamed from ppp0
root@router:~#

Note, the lack of anything related to the ath9K driver in the second dmesg.

Following the instructions on External Linkhttps://openwrt.org/docs/guide-user/network/wifi/basic to regenerate the wireless configuration:
rm -f /etc/config/wireless
wifi config

resulted in an empty /etc/config/wireless:
root@router:~# ls -all /etc/config/wireless
-rw-r–r– 1 root root 0 Feb 21 23:12 /etc/config/wireless
root@ router:~# cat /etc/config/wireless

Due to the rename of the platform from wndr3700v2 to wndr3700-v2 the build config had to be edited (recreated by a new run of menuconfig).

Let me know if I can do anything to help get this debugged.

22.02.20202849KernelBug ReportVery LowHighAR8327 can't work on hybid VLAN tagging mode.AllUnconfirmed Task Description

I have 2 vlan channel in family network for IPTV STB with VLAN 51 & 85. My router is WZR-HP-G302H which have the same hardware with WZR-HP-G300NH2.

With the default vlans1&2, I set the switch has 4 vlan channels:
vlan1 goes cpu(port0) tagged, lan(port1-4) untagged, wan(port5) off,
vlan2 goes cpu(port0) tagged, lan(port1-4) off, wan(port5) untagged,
vlan51(for multicast) goes cpu(port0) untagged, IPTV(port1) tagged, PC(port2-4) off, wan(port5) tagged,
vlan85(IPTV stream) goes cpu(port0) untagged, IPTV(port1) tagged, PC(port2-4) off, wan(port5) tagged.
And I use TTL to logon my IPTV STB, with ifconfig eth0&eht0.85, I can see the STB got both internet routing ip(192.168.2.x) & IPTV intranet ip(217.xxx.xxx.xxx), but when I’m trying to ping 192.168.2.1, it failed.
When I set wan(port5) with vlan51&85 off, the internet was back, and got acks from ping 192.168.1.1.
So I tried to replace wan to port1-4 ,IPTV port to port2-5 with all the possibility, it shows the same problem.

Then I try to use the route with AP mode:
vlan1 goes cpu(port0) tagged, lan(port1-5) untagged,
vlan51 goes cpu(port0) off, lan(port1-5) tagged,
vlan85 goes cpu(port0) off, lan(port1-5) tagged.
The STB still got 2 IPs , which 192.168.1.x & 217.xxx.xxx.xxx both offerd by Modem’s DHCP.
And the same problem appears: only port with both vlan51&85 turned off can got internet access, others not.

I tried firmwares openwrt-19.07.1-ath79-generic-buffalo_wzr-hp-g302h-a1a0-squashfs-sysupgrade.bin, openwrt-19.07.1-ar71xx-generic-wzr-hp-g300nh2-squashfs-sysupgrade.bin and openwrt-18.06.7-ar71xx-generic-wzr-hp-g300nh2-squashfs-sysupgrade, they shows the same problem while the port sets in hybird mode with vlan tagged & untagged.

So I have to seeks documents and troubleshoots for help. Finally I found the ticket:(https://dev.archive.openwrt.org/ticket/12181.html) told the same problem.
But the ticket is 5 yeas ago, and the ar8216.c no in 19.07.1 and 18.06.7 is definitely different, the “k”‘s path is no longer available with new ar8216.c, so I have to report the bug here again.
Is there any patch or a new fixed version of ar8216.c work with hybird mode which inculde tagged & untagged frame on the same port? Thank you very much.

25.02.20202856Base systemBug ReportVery LowHighWifi "dies" (hostapd drops all clients) on some ar71xx ...openwrt-19.07New Task Description

This issue is very strange, i don’t even know if it’s just faulty hardware but i have it happening on multiple devices now

Most affected hardware

  • Nanobridge M5 , in this case transmitting enough data can trigger it almost instantly
  • TL-WR841ND , in this case i had it happen like 3-4 times a year
  • CPE 210 v3 , in this case it happens like each week

For the last one, which is running 19.07 i found on the system log

Tue Feb 25 07:38:58 2020 daemon.notice hostapd: wlan0: AP-STA-DISCONNECTED [redacted mac1]
Tue Feb 25 07:38:58 2020 daemon.info hostapd: wlan0: STA [redacted mac1] IEEE 802.11: disassociated due to inactivity
Tue Feb 25 07:38:59 2020 daemon.info hostapd: wlan0: STA [redacted mac1] IEEE 802.11: deauthenticated due to inactivity (timer DEAUTH/REMOVE)
Tue Feb 25 07:41:32 2020 daemon.notice hostapd: wlan0: AP-STA-DISCONNECTED [redacted mac2]
Tue Feb 25 07:41:32 2020 daemon.info hostapd: wlan0: STA [redacted mac2] IEEE 802.11: disassociated due to inactivity
Tue Feb 25 07:41:33 2020 daemon.info hostapd: wlan0: STA [redacted mac2] IEEE 802.11: deauthenticated due to inactivity (timer DEAUTH/REMOVE)
Tue Feb 25 07:42:49 2020 daemon.notice hostapd: wlan0: AP-STA-POLL-OK [redacted mac3]
Tue Feb 25 07:49:55 2020 daemon.notice hostapd: wlan0: AP-STA-POLL-OK [redacted mac3]
Tue Feb 25 07:55:02 2020 daemon.notice hostapd: wlan0: AP-STA-POLL-OK [redacted mac3]
Tue Feb 25 08:00:15 2020 daemon.notice hostapd: wlan0: AP-STA-POLL-OK [redacted mac3]
Tue Feb 25 08:05:25 2020 daemon.notice hostapd: wlan0: AP-STA-POLL-OK [redacted mac3]
Tue Feb 25 08:10:44 2020 daemon.notice hostapd: wlan0: AP-STA-POLL-OK [redacted mac3]
Tue Feb 25 08:16:00 2020 daemon.notice hostapd: wlan0: AP-STA-POLL-OK [redacted mac3]
07.03.20202888KernelBug ReportVery LowHighkomd-ipsec4 missing files in latest snapshotTrunkUnconfirmed Task Description

xfrm4_mode_tunnel ,xfrm4_mode_transport and xfrm4_mode_beet are missing in package kmod-ipsec4, it results strongswan failed to add SAD entry, and return netlink error.
It seems that it’s because of https://github.com/openwrt/openwrt/commit/1556ed155a9aff8636733d27076107b3354c4c3e

10.03.20202893Base systemBug ReportVery LowHighEthernet port not receiving data on Ubiquiti LiteAP ac ...TrunkUnconfirmed Task Description

Hi,

The Ubiquiti LiteAP ac (LAP-120) does not receive incoming packets via eth0 with the latest snapshot (OpenWrt SNAPSHOT, r12498-2a18840cc7):

root@OpenWrt:/# ifconfig 
br-lan    Link encap:Ethernet  HWaddr B4:FB:E4:FA:FA:FA
          inet addr:192.168.1.1  Bcast:192.168.1.255  Mask:255.255.255.0
          inet6 addr: fdaa:a708:e003::1/60 Scope:Global
          inet6 addr: fe80::b6fb:e4ff:fefa:fafa/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:34 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 B)  TX bytes:4420 (4.3 KiB)

eth0      Link encap:Ethernet  HWaddr B4:FB:E4:FA:FA:FA  
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:49 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 B)  TX bytes:6622 (6.4 KiB)
          Interrupt:4

It works correctly with latest stable, 19.07.2.

Using tcpdump on the connected computer I see outgoing traffic from the device, but incoming traffic does not reach the device.

The device correctly detects link changes, but different link speeds make no difference:

[ 1536.519019] eth0: link down
[ 1536.522824] br-lan: port 1(eth0) entered disabled state
[ 1537.561807] eth0: link up (1000Mbps/Full duplex)
[ 1537.566554] br-lan: port 1(eth0) entered blocking state
[ 1537.571932] br-lan: port 1(eth0) entered forwarding state
[ 1541.719009] eth0: link down
[ 1541.722824] br-lan: port 1(eth0) entered disabled state
[ 1542.761703] eth0: link up (100Mbps/Half duplex)
[ 1542.766359] br-lan: port 1(eth0) entered blocking state
[ 1542.771738] br-lan: port 1(eth0) entered forwarding state
[ 1545.879008] eth0: link down
[ 1545.882820] br-lan: port 1(eth0) entered disabled state
[ 1546.921800] eth0: link up (10Mbps/Half duplex)
[ 1546.926365] br-lan: port 1(eth0) entered blocking state
[ 1546.931744] br-lan: port 1(eth0) entered forwarding state

Please find attached dmesg outputs for both snapshot (snap) and 19.07.2 (19072).

13.03.20202901Base systemBug ReportVery LowHighFlow offload not working properly in case of IPv6 (NAT6...openwrt-19.07Unconfirmed Task Description

Linksys WRT32X with NAT6 configuration.

On latest 19.07 branch r10959

With the flow_offload feature turned on, nat6 is not working properly.
The first (or several) TCP packets seemed to be fine but later packets were not properly transmitted. The connection was soon closed.

(In case of accessing ipv6.google.com, the browser would freeze. And the curl would freeze after receiving a portion of the HTML content.)

In the meantime, ICMPv6 worked normally.

After removing the FLOWOFFLOAD ip6tables record, everything is fine.
After inserting the `-m conntrack –cstate RELATED,ESTABLISHED -j ACCEPT` before the FLOWOFFLOAD everything is also fine.

IPv4 part looked normal even if flow_offload is on.

NAT6 worked on older versions like 18.04 branch with flow_offload enabled.

17.03.20202906Base systemBug ReportVery LowHighAdding v4 Static routes without selecting 'Advanced' Ta...openwrt-19.07Unconfirmed Task Description

Using Openwrt 19.07.2 release;
On TP-Link c2600 & N750(wdr4300 v1.4)

Observed behavior:

Adding a static v4 route i.e 172.16.253.0 via 172.16.253.254 in the Luci Static route page succesfully adds the route, and by default appears to select the local route table. However viewing the routes list in status or via ip r s on cli does not show the entry.

Work-Around:

Ensure that a different table is selected in the 'Advanced tab' then go back in and add it to the correct appropriate route table.



Expected behaviour:

Adding a static route add's it to the system route table irrespective of needing to switch into advanced tab and select a non-default route table first.


21.03.20202912Base systemBug ReportVery LowHighPhicomm K3 (bcm53xx) wifi channel can't be set to auto ...openwrt-19.07Unconfirmed Task Description

Device:Phicomm K3 (bcm53xx)
BUG:wifi channel can’t set to auto mode
Description:Wifi channel can’t set to auto mode in Network - Wireless.
When wireless channel sets to auto mode, wireless settings will change from AP to Cilent even I don’t do that.

23.03.20202922Base systemBug ReportVery LowHighNo COMFAST CF-E110NV2 8MB flash compatible versionTrunkUnconfirmed Task Description

CF-E110V2 is released with 8MB Flash (maybe it was before with 16 but apparently no longer, see forum discussions on CF-E110)
The current released package is only for 16MB flash

Can You generate and publicly release a 8MB flash compatible version too.

Hereafter the modified part of the dts file I’m using to compile my own FW (based on original OEM partition table).

flash@0 {
	compatible = "winbond,w25q64", "jedec,spi-nor";
	reg = <0>;
	spi-max-frequency = <25000000>;
	partitions {
		compatible = "fixed-partitions";
		#address-cells = <1>;
		#size-cells = <1>;
		partition@0 {
			label = "u-boot";
			reg = <0x000000 0x010000>;
			read-only;
		};
		art: partition@10000 {
			label = "art";
			reg = <0x010000 0x010000>;
			read-only;
		};
		partition@20000 {
			compatible = "denx,uimage";
			label = "firmware";
			reg = <0x020000 0x7d0000>;
		};
		partition@7f0000 {
			label = "nvram";
			reg = <0x7f0000 0x010000>;
			read-only;
		};
	};
};
 


26.03.20202931Base systemBug ReportVery LowHighloading package information never arrivedopenwrt-19.07Unconfirmed Task Description

using fresh install

from Luci interface goto menu
system/software
the loading package information never arrived

pushing the update list button
the loading package information never arrived

using the console
opk update, list... are working well


27.03.20202936DocumentationBug ReportVery LowHighDocumentation for Pogoplug results in brickTrunkUnconfirmed Task Description

[1] assumes that u-boot image is smaller than 512 KB, but this is no longer the case. Followed the instructions without a second thought and bricked my device. It could have used ${filesize} like the sections below it, or simply use 640 KiB instead of 512 KiB. (The 660 KiB in the section might be a typo, it is not multiple of 128 KiB)

Besides, links in [2] are mostly broken and outdated. In addition, for V4 A3 devices, there are no test pads for JTAG.

[1] https://openwrt.org/toh/cloudengines/pogoplug#single-stage_bootloader [2] https://openwrt.org/toh/cloudengines/pogo-v4

07.04.20202977Base systemBug ReportVery LowHighParameters sendopts seems to be bad formated in the cal...openwrt-19.07Unconfirmed Task Description

The options parameters sendopts define in /etc/config/network seems to be badly formated in the call of the command odhcp6c

In /etc/config/network:

 

option sendopts “11:00 15:456544 16:1234”

is parsed like this (show via ps|grep odhcp6c)
-x11 00 -x15 456544 -x16 1234

The syntax given by the help of odhcp6c is different:

-x <opt>:<val> Add option opt (with value val) in sent packets (cumulative)

		Examples of IPv6 address, string and base-16 encoded options:
		-x dns:2001:2001::1,2001:2001::2 - option 23
		-x 15:office - option 15 (userclass)
		-x 0x1f4:ABBA - option 500
		-x 202:'"file"' - option 202

It appears than the : is replace by a space in the call of the command.
Regarding the help of the command, it should be :
-x 11:00 -x 15:456544 -x 16:1234

Thanks
Regards

08.04.20202978KernelBug ReportVery LowHighmt7621 snapshot downloads lack of .ko file in kernel mo...TrunkUnconfirmed Task Description

There is no .ko file in kernel module package, such as
kmod-crypto-acompress_5.4.28-1_mipsel_24kc.ipk
kmod-crypto-aead_5.4.28-1_mipsel_24kc.ipk
kmod-crypto-deflate_5.4.28-1_mipsel_24kc.ipk
Previous downloads in late 2019 and current mt7620 downloads do include .ko file.

08.04.20202980Base systemBug ReportVery LowHighNo connection to Ethernet portTrunkUnconfirmed Task Description

Hi,
I can’t connect to my board with ethernet port, my chip is mt7688 and branch is master, I tested board with 19.07 branch, it seems all is OK.
Below are the logs with serial port :

root@OpenWrt:/# [  306.094979] mtk_soc_eth 10100000.ethernet eth0: transmit timed out
[  306.101270] mtk_soc_eth 10100000.ethernet eth0: dma_cfg:00000057
[  306.107392] mtk_soc_eth 10100000.ethernet eth0: tx_ring=0, base=0707c000, max=1024, ctx=1, dtx=0, fdx=0, next=1
[  306.117655] mtk_soc_eth 10100000.ethernet eth0: rx_ring=0, base=0701c000, max=1024, calc=0, drx=1
[  316.094980] mtk_soc_eth 10100000.ethernet eth0: transmit timed out
[  316.101273] mtk_soc_eth 10100000.ethernet eth0: dma_cfg:00000057
[  316.107393] mtk_soc_eth 10100000.ethernet eth0: tx_ring=0, base=0707c000, max=1024, ctx=1, dtx=0, fdx=0, next=1
[  316.117657] mtk_soc_eth 10100000.ethernet eth0: rx_ring=0, base=07070000, max=1024, calc=1023, drx=0
[  317.502718] rt3050-esw 10110000.esw: link changed 0x00
[  326.094981] mtk_soc_eth 10100000.ethernet eth0: transmit timed out
[  326.101274] mtk_soc_eth 10100000.ethernet eth0: dma_cfg:00000057
[  326.107394] mtk_soc_eth 10100000.ethernet eth0: tx_ring=0, base=0707c000, max=1024, ctx=2, dtx=0, fdx=0, next=2
[  326.117659] mtk_soc_eth 10100000.ethernet eth0: rx_ring=0, base=0701c000, max=1024, calc=1023, drx=0
[  336.094979] mtk_soc_eth 10100000.ethernet eth0: transmit timed out
[  336.101271] mtk_soc_eth 10100000.ethernet eth0: dma_cfg:00000057
[  336.107392] mtk_soc_eth 10100000.ethernet eth0: tx_ring=0, base=0707c000, max=1024, ctx=1, dtx=0, fdx=0, next=1
[  336.117656] mtk_soc_eth 10100000.ethernet eth0: rx_ring=0, base=07070000, max=1024, calc=1023, drx=0
[  346.094979] mtk_soc_eth 10100000.ethernet eth0: transmit timed out
[  346.101272] mtk_soc_eth 10100000.ethernet eth0: dma_cfg:00000057
[  346.107392] mtk_soc_eth 10100000.ethernet eth0: tx_ring=0, base=0707c000, max=1024, ctx=1, dtx=0, fdx=0, next=1
[  346.117654] mtk_soc_eth 10100000.ethernet eth0: rx_ring=0, base=0701c000, max=1024, calc=1023, drx=0
[  356.094981] mtk_soc_eth 10100000.ethernet eth0: transmit timed out
[  356.101273] mtk_soc_eth 10100000.ethernet eth0: dma_cfg:00000057
[  356.107393] mtk_soc_eth 10100000.ethernet eth0: tx_ring=0, base=0707c000, max=1024, ctx=1, dtx=0, fdx=0, next=1
[  356.117657] mtk_soc_eth 10100000.ethernet eth0: rx_ring=0, base=07070000, max=1024, calc=1023, drx=0
 


09.04.20202986Base systemBug ReportVery LowHighFunctionality broken by migration to DSA for Ubiquiti E...TrunkUnconfirmed Task Description

Supply the following if possible:
- Ubiquiti ER-X
- Trunk
- Build trunk of Openwrt and try to configure vlan enabled interfaces on an embedded switch.

Hi.

I have Ubiquiti ER-X which I have been using for quite a while and it was working just fine.
I was using it to route traffic from external internet connections to a ‘trunk’ port connected to a different OpenWrt device used as access point. So to clarify: I have one of the swich ports configured as ‘tagged’ (’tunk’) for multiple vlans.

Unfortunately commit 30644bc579e771e4b6dcc165ca966124e0259e1e that switched this device to use DSA for switch configuration have completely broken this setup.

And I’m not talking abut soft bricking - that was to be expected. Unfortunately DSA doesn’t provide functionality that was available in swconfig for years. Namely it seems to be impossible to configure switch ports to be ‘tagged’.

It looks like DSA is considered to be ‘the future’ but unfortunately it doesn’t see to be ready for prime time - it seems to be impossible to use DSA enabled devices in configurations that were perfectly possible before.

13.04.20203005Base systemBug ReportVery LowHighiptables ruleset order improvement optionTrunkUnconfirmed Task Description

Supply the following if possible:
- Device problem occurs on
TP-Link Archer C7 v5
- Software versions of OpenWrt/LEDE release, packages, etc.
19.07.2, just default packages
- Steps to reproduce
Current iptable ordering is badly pessimal (this repeats 3x, so 3 states get set for each connection, but thats for other news)
```
-A FORWARD -m comment –comment “!fw3: Custom forwarding rule chain” -j forwarding_rule
-A FORWARD -m conntrack –ctstate RELATED,ESTABLISHED -m comment –comment “!fw3” -j ACCEPT
-A FORWARD -m conntrack –ctstate INVALID -m comment –comment “!fw3” -j DROP
```
following does same job but does significantly less processing for typical case of in-state packets
```
-A FORWARD -m conntrack –ctstate RELATED,ESTABLISHED -m comment –comment “!fw3” -j ACCEPT
-A FORWARD -m conntrack –ctstate INVALID -m comment –comment “!fw3” -j DROP
-A FORWARD -m comment –comment “!fw3: Custom forwarding rule chain” -j forwarding_rule
```
Not willing to generalize, but my wifi and wire behind could not reach subscription 100Mbps in any way before the change, after change it is steady 100Mbps both ways.

14.04.20203008KernelBug ReportVery LowHighGenesys Logic USB 3.0 hub not recognized by the systemAllUnconfirmed Task Description

Hi) I have a problem with Genesys Logic USB 3.0 hub (based on GL3523) on my Xiaomi MiR3G. The system don’t see this hub. Same on 4.14 & 4.19 kernel. Bought on AliExpress

Workaround: insert a half of the plug into router port → the system recognize USB 2.0 hub, then insert the plug to the end → the system recognize USB 2.0 & USB 3.0 hubs as it must be.
1. Normal connect hub → the log is empty.
2. Insert a half of the plug:

root@MI-R3G:~# lsusb -v

Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               3.00
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         3
  bMaxPacketSize0         9
  idVendor           0x1d6b Linux Foundation
  idProduct          0x0003 3.0 root hub
  bcdDevice            4.19
  iManufacturer           3 Linux 4.19.114 xhci-hcd
  iProduct                2 xHCI Host Controller
  iSerial                 1 1e1c0000.xhci
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           31
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0 Full speed (or root) hub
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0004  1x 4 bytes
        bInterval              12
        bMaxBurst               0
Hub Descriptor:
  bLength              12
  bDescriptorType      42
  nNbrPorts             1
  wHubCharacteristic 0x0009
    Per-port power switching
    Per-port overcurrent protection
  bPwrOn2PwrGood       10 * 2 milli seconds
  bHubContrCurrent      0 milli Ampere
  bHubDecLat          0.0 micro seconds
  wHubDelay             0 nano seconds
  DeviceRemovable    0x00
 Hub Port Status:
   Port 1: 0000.02a0 5Gbps power Rx.Detect
Binary Object Store Descriptor:
  bLength                 5
  bDescriptorType        15
  wTotalLength           15
  bNumDeviceCaps          1
  SuperSpeed USB Device Capability:
    bLength                10
    bDescriptorType        16
    bDevCapabilityType      3
    bmAttributes         0x00
    wSpeedsSupported   0x0008
      Device can operate at SuperSpeed (5Gbps)
    bFunctionalitySupport   3
      Lowest fully-functional device speed is SuperSpeed (5Gbps)
    bU1DevExitLat           0 micro seconds
    bU2DevExitLat           0 micro seconds
Device Status:     0x0001
  Self Powered

Bus 001 Device 010: ID 05e3:0610 Genesys Logic, Inc. 4-port hub
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         2 TT per port
  bMaxPacketSize0        64
  idVendor           0x05e3 Genesys Logic, Inc.
  idProduct          0x0610 4-port hub
  bcdDevice            5.11
  iManufacturer           1 GenesysLogic
  iProduct                2 USB2.0 Hub
  iSerial                 0
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           41
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower              100mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      1 Single TT
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0001  1x 1 bytes
        bInterval              12
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       1
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      2 TT per port
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0001  1x 1 bytes
        bInterval              12
Hub Descriptor:
  bLength               9
  bDescriptorType      41
  nNbrPorts             4
  wHubCharacteristic 0x00e9
    Per-port power switching
    Per-port overcurrent protection
    TT think time 32 FS bits
    Port indicators
  bPwrOn2PwrGood       50 * 2 milli seconds
  bHubContrCurrent    100 milli Ampere
  DeviceRemovable    0x00
  PortPwrCtrlMask    0xff
 Hub Port Status:
   Port 1: 0000.0100 power
   Port 2: 0000.0100 power
   Port 3: 0000.0100 power
   Port 4: 0000.0100 power
Device Qualifier (for other device speed):
  bLength                10
  bDescriptorType         6
  bcdUSB               2.00
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         0 Full speed (or root) hub
  bMaxPacketSize0        64
  bNumConfigurations      1
Device Status:     0x0001
  Self Powered

Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         1 Single TT
  bMaxPacketSize0        64
  idVendor           0x1d6b Linux Foundation
  idProduct          0x0002 2.0 root hub
  bcdDevice            4.19
  iManufacturer           3 Linux 4.19.114 xhci-hcd
  iProduct                2 xHCI Host Controller
  iSerial                 1 1e1c0000.xhci
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           25
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0 Full speed (or root) hub
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0004  1x 4 bytes
        bInterval              12
Hub Descriptor:
  bLength               9
  bDescriptorType      41
  nNbrPorts             2
  wHubCharacteristic 0x0009
    Per-port power switching
    Per-port overcurrent protection
    TT think time 8 FS bits
  bPwrOn2PwrGood       10 * 2 milli seconds
  bHubContrCurrent      0 milli Ampere
  DeviceRemovable    0x00
  PortPwrCtrlMask    0xff
 Hub Port Status:
   Port 1: 0000.0503 highspeed power enable connect
   Port 2: 0000.0100 power
Device Status:     0x0001
  Self Powered

3. Insert the plug to the end:

root@MI-R3G:~# lsusb -v

Bus 001 Device 010: ID 05e3:0610 Genesys Logic, Inc. 4-port hub
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         2 TT per port
  bMaxPacketSize0        64
  idVendor           0x05e3 Genesys Logic, Inc.
  idProduct          0x0610 4-port hub
  bcdDevice            5.11
  iManufacturer           1 GenesysLogic
  iProduct                2 USB2.0 Hub
  iSerial                 0
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           41
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower              100mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      1 Single TT
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0001  1x 1 bytes
        bInterval              12
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       1
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      2 TT per port
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0001  1x 1 bytes
        bInterval              12
Hub Descriptor:
  bLength               9
  bDescriptorType      41
  nNbrPorts             4
  wHubCharacteristic 0x00e9
    Per-port power switching
    Per-port overcurrent protection
    TT think time 32 FS bits
    Port indicators
  bPwrOn2PwrGood       50 * 2 milli seconds
  bHubContrCurrent    100 milli Ampere
  DeviceRemovable    0x00
  PortPwrCtrlMask    0xff
 Hub Port Status:
   Port 1: 0000.0100 power
   Port 2: 0000.0100 power
   Port 3: 0000.0100 power
   Port 4: 0000.0100 power
Device Qualifier (for other device speed):
  bLength                10
  bDescriptorType         6
  bcdUSB               2.10
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         0 Full speed (or root) hub
  bMaxPacketSize0        64
  bNumConfigurations      1
Device Status:     0x0001
  Self Powered

Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         1 Single TT
  bMaxPacketSize0        64
  idVendor           0x1d6b Linux Foundation
  idProduct          0x0002 2.0 root hub
  bcdDevice            4.19
  iManufacturer           3 Linux 4.19.114 xhci-hcd
  iProduct                2 xHCI Host Controller
  iSerial                 1 1e1c0000.xhci
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           25
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0 Full speed (or root) hub
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0004  1x 4 bytes
        bInterval              12
Hub Descriptor:
  bLength               9
  bDescriptorType      41
  nNbrPorts             2
  wHubCharacteristic 0x0009
    Per-port power switching
    Per-port overcurrent protection
    TT think time 8 FS bits
  bPwrOn2PwrGood       10 * 2 milli seconds
  bHubContrCurrent      0 milli Ampere
  DeviceRemovable    0x00
  PortPwrCtrlMask    0xff
 Hub Port Status:
   Port 1: 0000.0503 highspeed power enable connect
   Port 2: 0000.0100 power
Device Status:     0x0001
  Self Powered

Bus 002 Device 006: ID 05e3:0620 Genesys Logic, Inc.
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               3.00
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         3
  bMaxPacketSize0         9
  idVendor           0x05e3 Genesys Logic, Inc.
  idProduct          0x0620
  bcdDevice            5.11
  iManufacturer           1 GenesysLogic
  iProduct                2 USB3.0 Hub
  iSerial                 0
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           31
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0 Full speed (or root) hub
      iInterface              1 GenesysLogic
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x83  EP 3 IN
        bmAttributes           19
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Feedback
        wMaxPacketSize     0x0002  1x 2 bytes
        bInterval               8
        bMaxBurst               0
Hub Descriptor:
  bLength              12
  bDescriptorType      42
  nNbrPorts             4
  wHubCharacteristic 0x0009
    Per-port power switching
    Per-port overcurrent protection
  bPwrOn2PwrGood       50 * 2 milli seconds
  bHubContrCurrent    576 milli Ampere
  bHubDecLat          0.4 micro seconds
  wHubDelay          1508 nano seconds
  DeviceRemovable    0x00
 Hub Port Status:
   Port 1: 0000.02a0 5Gbps power Rx.Detect
   Port 2: 0000.02a0 5Gbps power Rx.Detect
   Port 3: 0000.02a0 5Gbps power Rx.Detect
   Port 4: 0000.02a0 5Gbps power Rx.Detect
Binary Object Store Descriptor:
  bLength                 5
  bDescriptorType        15
  wTotalLength           42
  bNumDeviceCaps          3
  USB 2.0 Extension Device Capability:
    bLength                 7
    bDescriptorType        16
    bDevCapabilityType      2
    bmAttributes   0x00000006
      Link Power Management (LPM) Supported
  SuperSpeed USB Device Capability:
    bLength                10
    bDescriptorType        16
    bDevCapabilityType      3
    bmAttributes         0x00
    wSpeedsSupported   0x000e
      Device can operate at Full Speed (12Mbps)
      Device can operate at High Speed (480Mbps)
      Device can operate at SuperSpeed (5Gbps)
    bFunctionalitySupport   1
      Lowest fully-functional device speed is Full Speed (12Mbps)
    bU1DevExitLat           8 micro seconds
    bU2DevExitLat         190 micro seconds
  Container ID Device Capability:
    bLength                20
    bDescriptorType        16
    bDevCapabilityType      4
    bReserved               0
    ContainerID             {f0564b9f-f61d-e011-ac64-0800200c9a66}
Device Status:     0x0001
  Self Powered

Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               3.00
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         3
  bMaxPacketSize0         9
  idVendor           0x1d6b Linux Foundation
  idProduct          0x0003 3.0 root hub
  bcdDevice            4.19
  iManufacturer           3 Linux 4.19.114 xhci-hcd
  iProduct                2 xHCI Host Controller
  iSerial                 1 1e1c0000.xhci
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           31
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0 Full speed (or root) hub
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0004  1x 4 bytes
        bInterval              12
        bMaxBurst               0
Hub Descriptor:
  bLength              12
  bDescriptorType      42
  nNbrPorts             1
  wHubCharacteristic 0x0009
    Per-port power switching
    Per-port overcurrent protection
  bPwrOn2PwrGood       10 * 2 milli seconds
  bHubContrCurrent      0 milli Ampere
  bHubDecLat          0.0 micro seconds
  wHubDelay             0 nano seconds
  DeviceRemovable    0x00
 Hub Port Status:
   Port 1: 0000.0203 5Gbps power U0 enable connect
Binary Object Store Descriptor:
  bLength                 5
  bDescriptorType        15
  wTotalLength           15
  bNumDeviceCaps          1
  SuperSpeed USB Device Capability:
    bLength                10
    bDescriptorType        16
    bDevCapabilityType      3
    bmAttributes         0x00
    wSpeedsSupported   0x0008
      Device can operate at SuperSpeed (5Gbps)
    bFunctionalitySupport   3
      Lowest fully-functional device speed is SuperSpeed (5Gbps)
    bU1DevExitLat           0 micro seconds
    bU2DevExitLat           0 micro seconds
Device Status:     0x0001
  Self Powered

But after reboot the same: no hub at all.
Nope, the connector is normal, recognized correctly on PC & smartphone. So, this is kernel or driver bug.

21.04.20203031Base systemBug ReportVery LowHighBusybox force reinstalled when there are no opkg listsopenwrt-19.07Unconfirmed Task Description

Device problem occurs on: Turris Omnia, mvebu
Software version: OpenWrt 19.07.

Steps to reproduce:

I noticed this bug, when I forget to do before force-reinstalling busybox

opkg update

If there isn’t anything in folder /var/opkg-lists

root@turris:/# ls -la /var/opkg-lists
ls: /var/opkg-lists: No such file or directory

It is possible to remove busybox, which should not happen.

root@turris:/# opkg install busybox --force-reinstall
Removing package busybox from root...
Installing busybox (1.30.1-5.18) to root...
Collected errors:
 * opkg_download_pkg: Package busybox is not available from any configured src.
 * opkg_install_pkg: Failed to download busybox. Perhaps you need to run 'opkg update'?
 * opkg_install_cmd: Cannot install package busybox.

And then the device ends up being in a non-specific state when you can not do anything and you need to flash firmware it once again.

If you do

opkg update

before force-reinstalling busybox, it refuses to do it which is correct.

root@turris:~# opkg install busybox --force-reinstall
Refusing to remove essential package busybox.
        Removing an essential package may lead to an unusable system, but if
        you enjoy that kind of pain, you can force opkg to proceed against
        its will with the option: --force-removal-of-essential-packages
No packages removed.
Package busybox (1.30.1-5.18) installed in root is up to date.
22.04.20203038KernelBug ReportVery LowHighBuilding master for x86_64/generic fails with missing m...TrunkUnconfirmed Task Description

I’m building with the attached .config and kernel-config files on “master”, and getting the following failure:

make[3]: Entering directory ‘/home/philipp/lede2/package/kernel/linux’ mkdir -p /home/philipp/lede2/staging_dir/target-x86_64_musl/root-x86/stamp

SHELL= flock /home/philipp/lede2/tmp/.root-copy.flock -c ‘cp -fpR /home/philipp/lede2/build_dir/target-x86_64_musl/linux-x86_64/packages/.pkgdir/kernel/. /home/philipp/lede2/staging_dir/target-x86_64_musl/root-x86/’ touch /home/philipp/lede2/staging_dir/target-x86_64_musl/root-x86/stamp/.kernel_installed
ERROR: module ‘/home/philipp/lede2/build_dir/target-x86_64_musl/linux-x86_64/linux-5.4.34/net/ipv4/netfilter/nft_reject_ipv4.ko’ is missing.
modules/netfilter.mk:1068: recipe for target ‘/home/philipp/lede2/bin/targets/x86/64/packages/kmod-nft-core_5.4.34-1_x86_64.ipk’ failed
make[3]: * [/home/philipp/lede2/bin/targets/x86/64/packages/kmod-nft-core_5.4.34-1_x86_64.ipk] Error 1
make[3]: Leaving directory ‘/home/philipp/lede2/package/kernel/linux’ time: package/kernel/linux/compile#4.14#0.22#4.68
package/Makefile:111: recipe for target ‘package/kernel/linux/compile’ failed
make[2]:
* [package/kernel/linux/compile] Error 2
make[2]: Leaving directory ‘/home/philipp/lede2’ package/Makefile:107: recipe for target ‘/home/philipp/lede2/staging_dir/target-x86_64_musl/stamp/.package_compile’ failed
make[1]: * [/home/philipp/lede2/staging_dir/target-x86_64_musl/stamp/.package_compile] Error 2
make[1]: Leaving directory ‘/home/philipp/lede2’ /home/philipp/lede2/include/toplevel.mk:218: recipe for target ‘world’ failed
make:
* [world] Error 2

Looking through the sources, I see the module being copied, but I don’t see the requisite kernel configuration to force it to be built:

philipp@ubuntu16:~/lede2$ fgrep -i -r nft_reject_ipv4 Makefile rules.mk Config.in config include package target
include/netfilter.mk:$(eval $(if $(NF_KMOD),$(call nf_add,NFT_CORE,CONFIG_NFT_REJECT, $(P_XT)nft_reject $(P_V4)nft_reject_ipv4 $(P_V6)nft_reject_ipv6),))
philipp@ubuntu16:~/lede2$

I do see config state for nft_reject.ko however:

philipp@ubuntu16:~/lede2$ grep -i -r ‘nft_reject’ Makefile rules.mk Config.in config include package target
include/netfilter.mk:$(eval $(if $(NF_KMOD),$(call nf_add,NFT_CORE,CONFIG_NFT_REJECT, $(P_XT)nft_reject $(P_V4)nft_reject_ipv4 $(P_V6)nft_reject_ipv6),))
include/netfilter.mk:$(eval $(if $(NF_KMOD),$(call nf_add,NFT_CORE,CONFIG_NFT_REJECT_INET, $(P_XT)nft_reject_inet),))
include/netfilter.mk:$(eval $(if $(NF_KMOD),$(call nf_add,NFT_BRIDGE,CONFIG_NFT_BRIDGE_REJECT, $(P_EBT)nft_reject_bridge),))
philipp@ubuntu16:~/lede2$

and the synthesized .config in the kernel directory and the built modules are:

philipp@ubuntu16:~/lede2$ pushd build_dir/target-x86_64_musl/linux-x86_64/linux-5.4.34/
~/lede2/build_dir/target-x86_64_musl/linux-x86_64/linux-5.4.34 ~/lede2
philipp@ubuntu16:~/lede2/build_dir/target-x86_64_musl/linux-x86_64/linux-5.4.34$ grep NFT_REJECT .config*
.config:CONFIG_NFT_REJECT=m
.config.old:CONFIG_NFT_REJECT=m
.config.old:CONFIG_NFT_REJECT_INET=m
.config.override:CONFIG_NFT_REJECT=m
.config.override:CONFIG_NFT_REJECT_INET=m
.config.prev:CONFIG_NFT_REJECT=m
.config.prev:CONFIG_NFT_REJECT_INET=m
.config.set:CONFIG_NFT_REJECT=m
.config.set:CONFIG_NFT_REJECT_INET=m
philipp@ubuntu16:~/lede2/build_dir/target-x86_64_musl/linux-x86_64/linux-5.4.34$ find net/netfilter net/ipv[46]/netfilter -name “nft_reject*.ko” -ls

4498742    120 -rw-r--r--   1 philipp  philipp    120808 Apr 22 12:21 net/netfilter/nft_reject.ko

philipp@ubuntu16:~/lede2/build_dir/target-x86_64_musl/linux-x86_64/linux-5.4.34$

When I build, I get prompted for the following kernel symbols:

Verify kernel signature during kexec_file_load() syscall (KEXEC_SIG) [N/y/?] (NEW)

Netfilter nf_tables support (NF_TABLES) [M/n/y/?] m
Netfilter nf_tables set infrastructure (NF_TABLES_SET) [M/n/?] m
Netfilter nf_tables mixed IPv4/IPv6 tables support (NF_TABLES_INET) [N/y/?] (NEW)

IPv4 nf_tables support (NF_TABLES_IPV4) [N/y/?] (NEW)

IPv6 nf_tables support (NF_TABLES_IPV6) [N/y/?] (NEW)

Detect Hung Tasks (DETECT_HUNG_TASK) [Y/n/?] y
Default timeout for hung task detection (in seconds) (DEFAULT_HUNG_TASK_TIMEOUT) [120] (NEW)
Panic (Reboot) On Hung Tasks (BOOTPARAM_HUNG_TASK_PANIC) [N/y/?] (NEW)

which makes me wonder if part of the default kernel config is incorrect... including symbols like CONFIG_NFT_REJECT_IPV4, etc.

26.04.20203049KernelBug ReportVery LowHighsunxi / lamobo-r1: switch not working with kernel 5.4TrunkUnconfirmed Task Description

Supply the following if possible:
- Device problem occurs on

Lamobo-R1 BananaPI Router

- Software versions of OpenWrt/LEDE release, packages, etc.

OpenWRT Snapshots (Imagebuilder) sometime after r12688-46d0ce19f1

- Steps to reproduce

Write any recent image to SD card, it boots but networking does not work.


Hello,

I’m doing regular updates with imagebuilder (about once per week) for Lamobo-R1. Some time after r12688-46d0ce19f1 the networking configuration broke.
I’m assuming the cause is kernel 5.4, because my last working image is from 2020-03-22 and it stopped working the week after, around 2020-03-29.

As far as I can tell the problem lies in the switch configuration: The switch is not found, the bootlog of kernel 5.4 contains no reference to “b53”.

  [    3.050660] init: - preinit -
  [    3.200152] sun7i-dwmac 1c50000.ethernet eth0: no phy at addr -1
  [    3.206288] sun7i-dwmac 1c50000.ethernet eth0: stmmac_open: Cannot attach to PHY (error: -19)
  ifconfig: SIOCSIFFLAGS: No such device
  Failed to connect to the switch. Use the "list" command to see which switches are available.
  Failed to connect to the switch. Use the "list" command to see which switches are available.
  Failed to connect to the switch. Use the "list" command to see which switches are available.
  [    4.358791] random: jshn: uninitialized urandom read (4 bytes read)
  [    4.388472] random: jshn: uninitialized urandom read (4 bytes read)
  [    4.431303] random: jshn: uninitialized urandom read (4 bytes read)
  Failed to connect to the switch. Use the "list" command to see which switches are available.
  Failed to connect to the switch. Use the "list" command to see which switches are available.
  Failed to connect to the switch. Use the "list" command to see which switches are available.
  Failed to connect to the switch. Use the "list" command to see which switches are available.
  [    4.505287] sun7i-dwmac 1c50000.ethernet eth0: no phy at addr -1
  [    4.511309] sun7i-dwmac 1c50000.ethernet eth0: stmmac_open: Cannot attach to PHY (error: -19)
  ip: SIOCSIFFLAGS: No such device
  Press the [f] key and hit [enter] to enter failsafe mode
  Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
  sendto(): Network unreachable
  sendto(): Network unreachable
  [    8.622199] mount_root: mounting /dev/root

I’m attaching screenlogs of both old and new kernel boot and the corresponding device tree files (taken from the sdcard).

Please advise, thank you.

26.04.20203051PackagesBug ReportVery LowHighUPnP not workingAllUnconfirmed Task Description

Device: Linksys WRT1900ACSv2
Software versions: v19.07.9 and v19.07.2
Current Openwrt firmware: OpenWrt SNAPSHOT r13046-df27e949fb / LuCI Master git-20.113.57176-dc1d2ce
Affected Packages: miniupnpd, luci-app-upnp

I have flashed two versions of OpenWrt v19.07.2, one compiled by myself and the other using the official stable release from the website. On both versions I have then installed the latest version of the LuCI-app-UPnP which includes the miniupnpd daemon.

The problem is UPnP seems to very intermittent of how it picks up the ports from the devices. Some devices and applications show up under the `Active UPnP Redirects` and some don’t at all. My primary testing device is my Sony PS3 and PS4 which requires UPnP to open up ports for an optimal online gaming experience. A common port that I reply on is UDP 3074 that is used by Call of Duty games to achieve open NAT type.

When I was running OpenWrt v18.06.5 at the time in 2019 everything worked perfectly including UPnP. When v19.07.0 was officially released for stable use, I noticed I was getting moderate NAT type within my games. With this in mind I checked the luci-upnp app and noticed that my PS4’s IP address/hostname and the corresponding UDP 3074 was not listed. Sometimes I could get the PS4 to be picked up via the Sony PlayStation network test which would open up UDP port 9308 on LuCI-app-UPnP.

I have opened a couple of OpenWrt forum threads discussing UPnP not working:

The only working version of miniupnpd/luci-app-upnp seems to be miniupnpd 2.1-1 which I have had working on all the v19.07.* firmwares. OpenWrt v19.07.0 shipped with miniupnpd 2.1.20190408-2 and this was the point where it broke. Recently testing with the newer v19.07.2 firmware the miniupnpd has been updated to version 2.1.20191006 and this is the same story whereby the PS3/PS4 can’t be picked up.

Interestingly I did some experimenting and took the files, patches and makefile from the master trunk, replaced `PKG_VERSION:-2.1.20191006` with `PKG_VERSION:-2.1.20200329` in the `makefile` (which is the very latest version of the MiniUPnP daemon source code found at https://miniupnp.tuxfamily.org/files), compiled v19.07.2 and flashed it to my router. I then did a Sony PlayStation network test on my PS4 and UDP port 9308 was listed under `Active UPnP Redirects`. I then proceeded onto Call of Duty Modern Warfare (2019) and UDP port 3074 also appeared! However, I still had moderate NAT type which meant the firewall wasn’t opening up somewhere. After clicking the `Delete` button on the LuCI UPnP page and opening the port manually on the firewall the game did give me open NAT type as expected. Weirdly though, the UPnP listing came back which has never happened any time I’ve used OpenWrt with manual port forwards. In other words if I open a port manually in the firewall UPnP will never list same port and destination device in the `Active UPnP Redirects` list.

08.05.20203072Base systemBug ReportVery LowHighSamknows WhiteBox8 misses 2.4 GHz pcie wireless NICTrunkUnconfirmed Task Description

device

software versions

tested & misses 2.4 GHz NIC

tested & has 2.4 GHz NIC

reproduce

  • build OpenWrt master branch with a given commits and flash it on the device (my build config is attached)
  • run “iw dev” or “iw list”
    • in problem state it lists one interface (the 5 GHz wireless NIC)
    • in good state it lists two interfaces (2.4 GHz and 5 GHz wireless NIC)

conclusion

I think it has either to do with ramips: mt7621: switch kernel version to 5.4 or with ramips: mt7621: update PCIe node in dtsi. Between the known good and earliest known bad commit are multiple commits working together. I fear to test them one by one.

09.05.20203079Base systemBug ReportVery LowHighTraceback when booting OpenWrt 19.07.2 on Netgear r7500...TrunkUnconfirmed Task Description

My Netgear r7500v2 running OpenWrt 19.07.2 always shows the following traceback when booting up.

[ 31.917130] ————[ cut here ]———— [ 31.917192] WARNING: CPU: 1 PID: 1938 at backports-4.19.98-1/net/wireless/util.c:1147 0xbf2e3d88 [cfg80211@bf2df000+0×37000]
[ 31.920831] invalid rate bw=0, mcs=15, nss=4
[ 31.932143] Modules linked in: pppoe ppp_async ath10k_pci ath10k_core ath pppox ppp_generic nf_conntrack_ipv6 mac80211 iptable_nat ipt_REJECT ipt_MASQUERADE cfg80211 xt_time xt_tcpudp xt_state xt_nat xt_multiport xt_mark xt_mac xt_limit xt_conntrack xt_comment xt_TCPMSS xt_REDIRECT xt_LOG xt_FLOWOFFLOAD xt_CT wireguard slhc nf_reject_ipv4 nf_nat_redirect nf_nat_masquerade_ipv4 nf_conntrack_ipv4 nf_nat_ipv4 nf_nat nf_log_ipv4 nf_flow_table_hw nf_flow_table nf_defrag_ipv6 nf_defrag_ipv4 nf_conntrack_rtcache nf_conntrack iptable_mangle iptable_filter ip_tables crc_ccitt compat ledtrig_usbport nf_log_ipv6 nf_log_common ip6table_mangle ip6table_filter ip6_tables ip6t_REJECT x_tables nf_reject_ipv6 ip6_udp_tunnel udp_tunnel uas usb_storage f2fs ext4 mbcache jbd2 crc32c_generic crc32_generic leds_gpio xhci_plat_hcd
[ 31.985373] xhci_pci xhci_hcd dwc3 dwc3_of_simple ohci_platform ohci_hcd phy_qcom_dwc3 ahci ehci_platform sd_mod ahci_platform libahci_platform libahci libata scsi_mod ehci_hcd gpio_button_hotplug
[ 32.007657] CPU: 1 PID: 1938 Comm: hostapd Not tainted 4.14.171 #0
[ 32.025242] Hardware name: Generic DT based system
[ 32.031323] Function entered at [<c030f1c4>] from [<c030b390>]
[ 32.036095] Function entered at [<c030b390>] from [<c07c0664>]
[ 32.041911] Function entered at [<c07c0664>] from [<c031fa98>]
[ 32.047727] Function entered at [<c031fa98>] from [<c031faf8>]
[ 32.053544] Function entered at [<c031faf8>] from [<bf2e3d88>]
[ 32.059386] Function entered at [<bf2e3d88>] from [<bf2f17dc>]
[ 32.065179] Function entered at [<bf2f17dc>] from [<bf2fe5f4>]
[ 32.070992] Function entered at [<bf2fe5f4>] from [<bf2ff1e8>]
[ 32.076806] Function entered at [<bf2ff1e8>] from [<bf332ad0>]
[ 32.082632] Function entered at [<bf332ad0>] from [<bf332b60>]
[ 32.088438] Function entered at [<bf332b60>] from [<bf332bf8>]
[ 32.094255] Function entered at [<bf332bf8>] from [<bf2ed678>]
[ 32.100071] Function entered at [<bf2ed678>] from [<c06e190c>]
[ 32.105887] Function entered at [<c06e190c>] from [<c06e0128>]
[ 32.111702] Function entered at [<c06e0128>] from [<c06e0900>]
[ 32.117517] Function entered at [<c06e0900>] from [<c06df938>]
[ 32.123334] Function entered at [<c06df938>] from [<c06dfd54>]
[ 32.129150] Function entered at [<c06dfd54>] from [<c0689c18>]
[ 32.134967] Function entered at [<c0689c18>] from [<c068a480>]
[ 32.140782] Function entered at [<c068a480>] from [<c0307b60>]
[ 32.146678] —[ end trace 97f7e93c858c392e ]—

11.05.20203091KernelBug ReportVery LowHighLatest build does not work properly on Banana Pi R2TrunkUnconfirmed Task Description

I compile my image according to the given guide: https://openwrt.org/toh/sinovoip/sinovoip_banana_pi_r2

With kernel version 4.19 everything went smooth (OpenWrt Snapshot shown after boot was r12726-92616c4227).

Then i wanted to upgrade to the current master and after applying the new bpi_bananapi-r2-kernel.bin and root.squashfs files the boot process stops every time at the same point (see attached file boot.txt).

I did the follwing steps:

  1. ./scripts/feeds update -a
  2. ./scripts/feeds install -a
  3. make -j8 menuconfig
  4. follow instructions for menuconfig on guide
  5. make -j8 kernel_menuconfig
  6. follow instructions for kernel_menuconfig on guide
  7. I did not apply the patch that was given. I didn’t encounter any problems with failing network connections even with the old linux kernel. It also does not make any difference according to the current problem.
  8. make -j8
  9. changed repositories.conf according to the guide
  10. make image PROFILE=bpi_bananapi-r2
  11. apply new kernel-file and rootfs according to the guide

I tried this several times with different configurations but the result was the same anyway.

It seems like there is a bug at loading rootfs from MTD.

 


11.05.20203092Base systemBug ReportVery LowHighXiaomi Router 3G random rebootsopenwrt-19.07Unconfirmed Task Description

Supply the following if possible:
- Device problem occurs on
- Software versions of OpenWrt/LEDE release, packages, etc.
- Steps to reproduce

 

Hello,

I have a Xiaomi 3G router. Since the day I bought it I installed Openwrt and to tell you the truth, with version 18.06 I didn’t have any problem.

A few weeks ago I updated to the new version (19.07) using LuCI and it restarts me randomly.

I tried restoring the router, reinstalling the update and it keeps randomly rebooting. Right now I have it without any additional packages installed and it still keeps rebooting randomly.

I have noticed, that almost every time I see a reboot and look at the log file the first thing that appears is this, that is, the first line after the reboot is:

Mon May 11 22:16:59 2020 daemon.info dnsmasq[1148]: exiting on receipt of SIGTERM
Mon May 11 22:16:59 2020 daemon.info dnsmasq[2722]: started, version 2.80 cachesize 150
Mon May 11 22:16:59 2020 daemon.info dnsmasq[2722]: DNS service limited to local subnets
Mon May 11 22:16:59 2020 daemon.info dnsmasq[2722]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth no-DNSSEC no-ID loop-detect inotify dumpfile
Mon May 11 22:16:59 2020 daemon.info dnsmasq-dhcp[2722]: DHCP, IP range 192.168.2.100 -- 192.168.2.249, lease time 12h
Mon May 11 22:16:59 2020 daemon.info dnsmasq[2722]: using local addresses only for domain test
Mon May 11 22:16:59 2020 daemon.info dnsmasq[2722]: using local addresses only for domain onion
Mon May 11 22:16:59 2020 daemon.info dnsmasq[2722]: using local addresses only for domain localhost
Mon May 11 22:16:59 2020 daemon.info dnsmasq[2722]: using local addresses only for domain local
Mon May 11 22:16:59 2020 daemon.info dnsmasq[2722]: using local addresses only for domain invalid
Mon May 11 22:16:59 2020 daemon.info dnsmasq[2722]: using local addresses only for domain bind
Mon May 11 22:16:59 2020 daemon.info dnsmasq[2722]: using local addresses only for domain lan
Mon May 11 22:16:59 2020 daemon.info dnsmasq[2722]: reading /tmp/resolv.conf.auto
Mon May 11 22:16:59 2020 daemon.info dnsmasq[2722]: using local addresses only for domain test
Mon May 11 22:16:59 2020 daemon.info dnsmasq[2722]: using local addresses only for domain onion
Mon May 11 22:16:59 2020 daemon.info dnsmasq[2722]: using local addresses only for domain localhost
Mon May 11 22:16:59 2020 daemon.info dnsmasq[2722]: using local addresses only for domain local
Mon May 11 22:16:59 2020 daemon.info dnsmasq[2722]: using local addresses only for domain invalid
Mon May 11 22:16:59 2020 daemon.info dnsmasq[2722]: using local addresses only for domain bind
Mon May 11 22:16:59 2020 daemon.info dnsmasq[2722]: using local addresses only for domain lan

Please, I need help since I can’t work if it constantly resets. If you need any more information, please do not hesitate to ask me.

29.05.20203134Base systemBuild FailureVery LowHighCan't build netifdopenwrt-19.07Unconfirmed Task Description

Environment: x86_64
Arch Linux
Description: Can’t build current openwrt-19.07. (Arch Linux, tried both GCC 10.1.0 and 8.4.0. Getting two build errors:

CFLAGS="-Os -pipe -mno-branch-likely -mips32r2 -mtune=74kc -fno-caller-saves -fno-plt -fhonour-copts -Wno-error=unused-but-set-variable -Wno-error=unused-result -msoft-float -mips16 -minterlin
k-mips16 -iremap/home/legogris/dev/openwrt-fresh/build_dir/target-mipsel_74kc_musl/netifd-2019-08-05-5e02f944:netifd-2019-08-05-5e02f944 -Wformat -Werror=format-security -fstack-protector -D_F
ORTIFY_SOURCE=1 -Wl,-z,now -Wl,-z,relro -I/home/legogris/dev/openwrt-fresh/staging_dir/target-mipsel_74kc_musl/usr/include/libnl-tiny -I/home/legogris/dev/openwrt-fresh/staging_dir/target-mips
el_74kc_musl/usr/include -flto  -I/home/legogris/dev/openwrt-fresh/staging_dir/target-mipsel_74kc_musl/usr/include -I/home/legogris/dev/openwrt-fresh/staging_dir/target-mipsel_74kc_musl/includ
e -I/home/legogris/dev/openwrt-fresh/staging_dir/toolchain-mipsel_74kc_gcc-7.5.0_musl/usr/include -I/home/legogris/dev/openwrt-fresh/staging_dir/toolchain-mipsel_74kc_gcc-7.5.0_musl/include/fo
rtify -I/home/legogris/dev/openwrt-fresh/staging_dir/toolchain-mipsel_74kc_gcc-7.5.0_musl/include " CXXFLAGS="-Os -pipe -mno-branch-likely -mips32r2 -mtune=74kc -fno-caller-saves -fno-plt -fho
nour-copts -Wno-error=unused-but-set-variable -Wno-error=unused-result -msoft-float -mips16 -minterlink-mips16 -iremap/home/legogris/dev/openwrt-fresh/build_dir/target-mipsel_74kc_musl/netifd-
2019-08-05-5e02f944:netifd-2019-08-05-5e02f944 -Wformat -Werror=format-security -fstack-protector -D_FORTIFY_SOURCE=1 -Wl,-z,now -Wl,-z,relro -I/home/legogris/dev/openwrt-fresh/staging_dir/tar
get-mipsel_74kc_musl/usr/include/libnl-tiny -I/home/legogris/dev/openwrt-fresh/staging_dir/target-mipsel_74kc_musl/usr/include -flto  -I/home/legogris/dev/openwrt-fresh/staging_dir/target-mips
el_74kc_musl/usr/include -I/home/legogris/dev/openwrt-fresh/staging_dir/target-mipsel_74kc_musl/include -I/home/legogris/dev/openwrt-fresh/staging_dir/toolchain-mipsel_74kc_gcc-7.5.0_musl/usr/
include -I/home/legogris/dev/openwrt-fresh/staging_dir/toolchain-mipsel_74kc_gcc-7.5.0_musl/include/fortify -I/home/legogris/dev/openwrt-fresh/staging_dir/toolchain-mipsel_74kc_gcc-7.5.0_musl/
include " LDFLAGS="-L/home/legogris/dev/openwrt-fresh/staging_dir/target-mipsel_74kc_musl/usr/lib -L/home/legogris/dev/openwrt-fresh/staging_dir/target-mipsel_74kc_musl/lib -L/home/legogris/de
v/openwrt-fresh/staging_dir/toolchain-mipsel_74kc_gcc-7.5.0_musl/usr/lib -L/home/legogris/dev/openwrt-fresh/staging_dir/toolchain-mipsel_74kc_gcc-7.5.0_musl/lib -znow -zrelro -flto -fuse-linke
r-plugin " make  -C /home/legogris/dev/openwrt-fresh/build_dir/target-mipsel_74kc_musl/netifd-2019-08-05-5e02f944/. AR="mipsel-openwrt-linux-musl-gcc-ar" AS="mipsel-openwrt-linux-musl-gcc -c -
Os -pipe -mno-branch-likely -mips32r2 -mtune=74kc -fno-caller-saves -fno-plt -fhonour-copts -Wno-error=unused-but-set-variable -Wno-error=unused-result -msoft-float -iremap/home/legogris/dev/o
penwrt-fresh/build_dir/target-mipsel_74kc_musl/netifd-2019-08-05-5e02f944:netifd-2019-08-05-5e02f944 -Wformat -Werror=format-security -fstack-protector -D_FORTIFY_SOURCE=1 -Wl,-z,now -Wl,-z,re
lro -I/home/legogris/dev/openwrt-fresh/staging_dir/target-mipsel_74kc_musl/usr/include/libnl-tiny -I/home/legogris/dev/openwrt-fresh/staging_dir/target-mipsel_74kc_musl/usr/include -flto" LD=m
ipsel-openwrt-linux-musl-ld NM="mipsel-openwrt-linux-musl-gcc-nm" CC="mipsel-openwrt-linux-musl-gcc" GCC="mipsel-openwrt-linux-musl-gcc" CXX="mipsel-openwrt-linux-musl-g++" RANLIB="mipsel-open
wrt-linux-musl-gcc-ranlib" STRIP=mipsel-openwrt-linux-musl-strip OBJCOPY=mipsel-openwrt-linux-musl-objcopy OBJDUMP=mipsel-openwrt-linux-musl-objdump SIZE=mipsel-openwrt-linux-musl-size CROSS="
mipsel-openwrt-linux-musl-" ARCH="mipsel" CMAKE_COMMAND='/home/legogris/dev/openwrt-fresh/staging_dir/host/bin/cmake' CMAKE_DISABLE_cmake_check_build_system=1 ;
make[4]: Entering directory '/home/legogris/dev/openwrt-fresh/build_dir/target-mipsel_74kc_musl/netifd-2019-08-05-5e02f944'
make[5]: Entering directory '/home/legogris/dev/openwrt-fresh/build_dir/target-mipsel_74kc_musl/netifd-2019-08-05-5e02f944'
make[6]: Entering directory '/home/legogris/dev/openwrt-fresh/build_dir/target-mipsel_74kc_musl/netifd-2019-08-05-5e02f944'
make[6]: Leaving directory '/home/legogris/dev/openwrt-fresh/build_dir/target-mipsel_74kc_musl/netifd-2019-08-05-5e02f944'
make[6]: Entering directory '/home/legogris/dev/openwrt-fresh/build_dir/target-mipsel_74kc_musl/netifd-2019-08-05-5e02f944'
[  4%] Building C object CMakeFiles/netifd.dir/main.c.o
In file included from /home/legogris/dev/openwrt-fresh/build_dir/target-mipsel_74kc_musl/netifd-2019-08-05-5e02f944/netifd.h:29:0,
                 from /home/legogris/dev/openwrt-fresh/build_dir/target-mipsel_74kc_musl/netifd-2019-08-05-5e02f944/main.c:22:
/home/legogris/dev/openwrt-fresh/build_dir/target-mipsel_74kc_musl/netifd-2019-08-05-5e02f944/utils.h:116:51: error: 'struct uci_blob_param_list' declared inside parameter list will not be vis
ible outside of this definition or declaration [-Werror]
 const char * uci_get_validate_string(const struct uci_blob_param_list *p, int i);
                                                   ^~~~~~~~~~~~~~~~~~~
cc1: error: unrecognized command line option '-Wno-unknown-warning-option' [-Werror]
cc1: all warnings being treated as errors
make[6]: *** [CMakeFiles/netifd.dir/build.make:63: CMakeFiles/netifd.dir/main.c.o] Error 1
make[6]: Leaving directory '/home/legogris/dev/openwrt-fresh/build_dir/target-mipsel_74kc_musl/netifd-2019-08-05-5e02f944'
make[5]: *** [CMakeFiles/Makefile2:76: CMakeFiles/netifd.dir/all] Error 2
make[5]: Leaving directory '/home/legogris/dev/openwrt-fresh/build_dir/target-mipsel_74kc_musl/netifd-2019-08-05-5e02f944'
make[4]: *** [Makefile:130: all] Error 2
make[4]: Leaving directory '/home/legogris/dev/openwrt-fresh/build_dir/target-mipsel_74kc_musl/netifd-2019-08-05-5e02f944'
make[3]: *** [Makefile:49: /home/legogris/dev/openwrt-fresh/build_dir/target-mipsel_74kc_musl/netifd-2019-08-05-5e02f944/.built] Error 2
make[3]: Leaving directory '/home/legogris/dev/openwrt-fresh/package/network/config/netifd'
time: package/network/config/netifd/compile#0.33#0.08#0.39
make[2]: *** [package/Makefile:113: package/network/config/netifd/compile] Error 2
make[2]: Leaving directory '/home/legogris/dev/openwrt-fresh'
make[1]: *** [package/Makefile:107: /home/legogris/dev/openwrt-fresh/staging_dir/target-mipsel_74kc_musl/stamp/.package_compile] Error 2
make[1]: Leaving directory '/home/legogris/dev/openwrt-fresh'
make: *** [/home/legogris/dev/openwrt-fresh/include/toplevel.mk:227: world] Error 2
make -j1 V=s  20,02s user 4,25s system 102% cpu 23,565 total
30.05.20203138KernelBug ReportVery LowHighmac802.11sh commit broken and causing one radio to dropAllUnconfirmed Task Description

Source of the problem: commit `b551660` `/lib/netifd/wireless/mac802.11sh`
Device problem occurs on: Netgear R7800, LinksysWRT1900ACSv2, Netgear EX6400, TP-Link Archer C60
Software versions of OpenWrt/LEDE: v19.07.3 and master

Steps to reproduce: I created a post here https://forum.openwrt.org/t/wrt1900acsv2-only-one-wifi-radio-is-staying-up/64273 regarding the last WiFi client disconnecting from the AP stops working on that radio.

If I go into ‘Network > Wireless’ in LuCI and click the ‘Restart’ button on the 2.4 or 5GHz radio, that radio is the only radio that stays working, whereas the other radio says disabled and wireless not associated.

I can also replicate this via SSH/CLI running `wifi up radio0` disables radio1. Running `wifi up` brings radio1 up this but drops radio0. If I run `wifi up` a second time both radios come back up.

My forum has been linked to a Netgear 7800 thread found here https://forum.openwrt.org/t/netgear-r7800-exploration-ipq8065-qca9984/285/2259 and there has been confirmation that there appears to be a problem with commit `b551660` from May 4, 2020 for `openwrt/package/kernel/mac80211/files/lib/netifd/wireless/mac80211.sh`. Rolling back to commit `0495324` appears to fix this issue.

I too can confirm this by renaming `mac80211.sh` to `mac80211.sh.old`, downloading commit `0495324`, placing it under `/lib/netifd/wireless`, setting the permissions to `0755` and then running `wifi up radio0` in SSH/CLI. Radio0 (5GHz) drops as expected and after a couple of seconds it is back up all without affecting the radio1 (2.4GHz).

This is the broken commit https://github.com/openwrt/openwrt/commit/b5516603dd90215d5cdc5bac7ea496a6c758bb0f

This is the working commit https://github.com/openwrt/openwrt/commit/0e522d5f4a31182312bd115c26c7edb654769724

03.06.20203147Base systemBug ReportVery LowHigh802.11w settings on LUCI WIFI page doesn't work properl...openwrt-19.07Unconfirmed Task Description

Host device

Device problem occurs on: Phicomm PSG1218A (MTK7620, 64M, 8MB, 802.11AC+N)
Software versions of OpenWrt/LEDE release: OpenWRT 19.07.3 Stable (r11063-85e04e9f46 / LuCI openwrt-19.07 branch git-20.136.49537-fb2f363)
Package: wpad-openssl OR hostapd-openssl

External server/service

RADIUS server: Windows Server 2019 NPAS, worked fine with WPA2-EAP

Client

Client WIFI chip and driver: Intel Dual Band Wireless-AC 8265 running newest driver version 20.70.16.4 (driver date: 01/01/2020)

Steps to reproduce:

1. initialize default settings, then remove wpad-basic and install wpad-openssl OR hostapd-openssl to enable WPA3 AP mode
2. leave 802.11w to default setting which is “Required” 3. set country setting, ssid, and etc. as required such as radius for EAP
4 if use WPA2-PSK or WPA2-EAP with default settings, everything works fine.

5. switch WIFI (AC/N) to WPA2-PSK/WPA3-SAE mixed mode (sae+ccmp or something like that) OR WPA2-EAP/WPA3-EAP mixed mode (wpa3-mixed+ccmp or something like that)
6. apply settings wait until effective or reboot to take effect

6.1 __ssid won't come up on 802.11g/n interface__ if in PSK/SAE mixed mode.

7. Client (Intel 8265) won’t be able to connect to SSID,

7.1 if ssid would come up (802.11a/ac), it would be seen on client scan, but the client (Intel 8265) won't be able to connect to SSID, reports "Can't connect", in EAP mode, router side log "Deauthenticated due to local request" after "EAP-SUCCESS"

8. switch 802.11w to other settings, including “Optional”, problem remains, router config file /etc/config/wireless would list “option ieee80211w ‘1’” 9. switch 802.11w to other settings, including “Optional”, problem still remains, router config file /etc/config/wireless will be missing the “option ieee80211w” completely, and it seems wpad or hostapd would assume “optional” (code ‘1’) as default value instead of the documented “disabled” (code ‘0’).

Steps to workaround:

Manually set “option ieee80211w ‘0’” in /etc/config/wireless to disable 802.11w and don’t update settings through LUCI on the problematic ssid, restart wifi. Everything would work.

06.06.20203154KernelBug ReportVery LowHighXFRM state insert failure with AES-GCMopenwrt-19.07Unconfirmed Task Description

Supply the following if possible:
- Device problem occurs on
- Software versions of OpenWrt/LEDE release, packages, etc.
- Steps to reproduce

 

X86_64 arch, kernel fails to insert XFRM states with AES-GCM as transform.
Testable with
ip x s add proto esp dst 14.0.0.70 src 14.0.0.52 spi 0×07 mode transport reqid 0×07 replay-window 32 aead ‘rfc4106(gcm(aes))’ 0x44434241343332312423222114131211f4f3f2f1 128 sel src 14.0.0.52/24 dst 14.0.0.70/24 proto tcp

Works on Arch.
Result on X86_64 OpenWRT 19.07.3:
RTNETLINK answers: No such file or directory

On Arch 5.6.15-arch1-1, works (no output, ip x s shows the state).
Also fails 100% of the time when tested using an IKE keying daemon, e.g. strongSwan

12.06.20203176Base systemBug ReportVery LowHighpi zero AP+STA mode does not workAllUnconfirmed Task Description

Supply the following if possible:
- device: Raspberry Pi Zero W
- Versions confirmed on: recent Snapshot, 19.07.3, 18.06.8, 17.01.4
- Steps to reproduce:

  1. flash image to sd card, put sd card into pi
  2. turn on wifi radio (uci set wireless.radio0.disabled=0)
  3. add a wireless network such that one is a station and one is a AP (I’ve tried though gui and command line)
  4. restart wifi (either through reboot or wifi command)
  5. Now in the dmesg you can see wlan0-1 cycling between blocking forwarding and disabled states

Additional info:
I made this forum post about it, but not much has come from that and I’ve learned a lot since posting.

I know that this mode is supported from the iw list output -

 valid interface combinations:
                 * #{ managed } <= 1, #{ P2P-device } <= 1, #{ P2P-client, P2P-GO } <= 1,
                   total <= 3, #channels <= 2
                 * #{ managed } <= 1, #{ AP } <= 1, #{ P2P-client } <= 1, #{ P2P-device } <= 1,
                   total <= 4, #channels <= 1
        Supported extended features:
                * [ 4WAY_HANDSHAKE_STA_PSK ]: 4-way handshake with PSK in station mode
                * [ 4WAY_HANDSHAKE_STA_1X ]: 4-way handshake with 802.1X in station mode

I’ve even gotten AP+STA mode to work by manually starting a second instance of hostapd (note that im not killing the original one), but that makes it even more confusing that it doesn’t work normally.

I make sure that they are on the same channel.

If you need anything cleared up please let me know. I’ve tried for over a week now to fix this myself to no avail.

14.06.20203181Base systemBug ReportVery LowHighunable to build 19.07.3 for clearfog proopenwrt-19.07Unconfirmed Task Description

Supply the following if possible:
- Device problem occurs on
Clearfog pro

- Software versions of OpenWrt/LEDE release, packages, etc.
tag 19.07.3
- Steps to reproduce
make fails:

export CROSS="arm-openwrt-linux-muslgnueabi-"  NO_RENAME=1 ; NM="arm-openwrt-linux-muslgnueabi-nm" STRIP="/home/oli/openwrt/staging_dir/host/bin/sstrip" STRIP_KMOD="/home/oli/openwrt/scripts/strip-kmod.sh" PATCHELF="/home/oli/openwrt/staging_dir/host/bin/patchelf" /home/oli/openwrt/scripts/rstrip.sh /home/oli/openwrt/build_dir/target-arm_cortex-a9+vfpv3-d16_musl_eabi/u-boot-2018.03/ipkg-arm_cortex-a9_vfpv3-d16/uboot-envtools
rstrip.sh: /home/oli/openwrt/build_dir/target-arm_cortex-a9+vfpv3-d16_musl_eabi/u-boot-2018.03/ipkg-arm_cortex-a9_vfpv3-d16/uboot-envtools/usr/sbin/fw_printenv: executable
(cd /home/oli/openwrt/build_dir/target-arm_cortex-a9+vfpv3-d16_musl_eabi/u-boot-2018.03/ipkg-arm_cortex-a9_vfpv3-d16/uboot-envtools/CONTROL; ( echo "$CONTROL"; printf "Description: "; echo "$DESCRIPTION" | sed -e 's,^[[:space:]]*, ,g'; ) > control; chmod 644 control; ( echo "#!/bin/sh"; echo "[ \"\${IPKG_NO_SCRIPT}\" = \"1\" ] && exit 0"; echo "[ -x "\${IPKG_INSTROOT}/lib/functions.sh" ] || exit 0"; echo ". \${IPKG_INSTROOT}/lib/functions.sh"; echo "default_postinst \$0 \$@"; ) > postinst; ( echo "#!/bin/sh"; echo "[ -x "\${IPKG_INSTROOT}/lib/functions.sh" ] || exit 0"; echo ". \${IPKG_INSTROOT}/lib/functions.sh"; echo "default_prerm \$0 \$@"; ) > prerm; chmod 0755 postinst prerm; echo "$V_Package_uboot_envtools_conffiles" > conffiles;  )
install -d -m0755 /home/oli/openwrt/bin/targets/mvebu/cortexa9/packages
/home/oli/openwrt/scripts/ipkg-build -c -o 0 -g 0 /home/oli/openwrt/build_dir/target-arm_cortex-a9+vfpv3-d16_musl_eabi/u-boot-2018.03/ipkg-arm_cortex-a9_vfpv3-d16/uboot-envtools /home/oli/openwrt/bin/targets/mvebu/cortexa9/packages
/home/oli/openwrt/staging_dir/host/bin/find: '/home/oli/openwrt/build_dir/target-arm_cortex-a9+vfpv3-d16_musl_eabi/u-boot-2018.03/ipkg-arm_cortex-a9_vfpv3-d16/uboot-envtools/etc/config/ubootenv': No such file or directory
/home/oli/openwrt/staging_dir/host/bin/find: '/home/oli/openwrt/build_dir/target-arm_cortex-a9+vfpv3-d16_musl_eabi/u-boot-2018.03/ipkg-arm_cortex-a9_vfpv3-d16/uboot-envtools/etc/fw_env.config': No such file or directory
Packaged contents of /home/oli/openwrt/build_dir/target-arm_cortex-a9+vfpv3-d16_musl_eabi/u-boot-2018.03/ipkg-arm_cortex-a9_vfpv3-d16/uboot-envtools into /home/oli/openwrt/bin/targets/mvebu/cortexa9/packages/uboot-envtools_2018.03-3_arm_cortex-a9_vfpv3-d16.ipk
echo "uboot-envtools" >> /home/oli/openwrt/staging_dir/target-arm_cortex-a9+vfpv3-d16_musl_eabi/pkginfo/uboot-envtools.default.install
make[3]: Leaving directory '/home/oli/openwrt/package/boot/uboot-envtools'
time: package/boot/uboot-envtools/compile#1.27#0.68#1.71
make[3]: Entering directory '/home/oli/openwrt/package/boot/uboot-mvebu'
rm -f /home/oli/openwrt/build_dir/target-arm_cortex-a9+vfpv3-d16_musl_eabi/u-boot-clearfog/u-boot-2018.03/.built
touch /home/oli/openwrt/build_dir/target-arm_cortex-a9+vfpv3-d16_musl_eabi/u-boot-clearfog/u-boot-2018.03/.built_check
make  -C /home/oli/openwrt/build_dir/target-arm_cortex-a9+vfpv3-d16_musl_eabi/u-boot-clearfog/u-boot-2018.03 CROSS_COMPILE=arm-openwrt-linux-muslgnueabi- DTC="/home/oli/openwrt/build_dir/target-arm_cortex-a9+vfpv3-d16_musl_eabi/linux-mvebu_cortexa9/linux-4.14.180/scripts/dtc/dtc" HOSTCC="gcc" HOSTCFLAGS="-O2 -I/home/oli/openwrt/staging_dir/host/include -I/home/oli/openwrt/staging_dir/hostpkg/include -I/home/oli/openwrt/staging_dir/target-arm_cortex-a9+vfpv3-d16_musl_eabi/host/include -I/home/oli/openwrt/staging_dir/host/include -I/home/oli/openwrt/staging_dir/hostpkg/include -I/home/oli/openwrt/staging_dir/target-arm_cortex-a9+vfpv3-d16_musl_eabi/host/include -std=gnu11" HOSTLDFLAGS="-L/home/oli/openwrt/staging_dir/host/lib -L/home/oli/openwrt/staging_dir/hostpkg/lib -L/home/oli/openwrt/staging_dir/target-arm_cortex-a9+vfpv3-d16_musl_eabi/host/lib"
make[4]: Entering directory '/home/oli/openwrt/build_dir/target-arm_cortex-a9+vfpv3-d16_musl_eabi/u-boot-clearfog/u-boot-2018.03'
  CHK     include/config/uboot.release
  CHK     include/generated/version_autogenerated.h
  CHK     include/generated/timestamp_autogenerated.h
  CC      lib/asm-offsets.s
  CHK     include/generated/generic-asm-offsets.h
  UPD     include/generated/generic-asm-offsets.h
  CC      arch/arm/lib/asm-offsets.s
  CHK     include/generated/asm-offsets.h
  UPD     include/generated/asm-offsets.h
  HOSTLD  scripts/dtc/dtc
/usr/bin/ld: scripts/dtc/dtc-parser.tab.o:(.bss+0x10): multiple definition of `yylloc'; scripts/dtc/dtc-lexer.lex.o:(.bss+0x0): first defined here
collect2: error: ld returned 1 exit status
make[6]: *** [scripts/Makefile.host:108: scripts/dtc/dtc] Error 1
make[5]: *** [scripts/Makefile.build:425: scripts/dtc] Error 2
make[4]: *** [Makefile:491: scripts] Error 2
make[4]: Leaving directory '/home/oli/openwrt/build_dir/target-arm_cortex-a9+vfpv3-d16_musl_eabi/u-boot-clearfog/u-boot-2018.03'
make[3]: *** [Makefile:53: /home/oli/openwrt/build_dir/target-arm_cortex-a9+vfpv3-d16_musl_eabi/u-boot-clearfog/u-boot-2018.03/.built] Error 2
make[3]: Leaving directory '/home/oli/openwrt/package/boot/uboot-mvebu'
time: package/boot/uboot-mvebu/clearfog/compile#0.32#0.20#0.51
make[2]: *** [package/Makefile:113: package/boot/uboot-mvebu/compile] Error 2
make[2]: Leaving directory '/home/oli/openwrt'
make[1]: *** [package/Makefile:107: /home/oli/openwrt/staging_dir/target-arm_cortex-a9+vfpv3-d16_musl_eabi/stamp/.package_compile] Error 2
make[1]: Leaving directory '/home/oli/openwrt'
make: *** [/home/oli/openwrt/include/toplevel.mk:227: world] Fehler 2
18.06.20203190KernelBug ReportVery LowHighKernel Oops and reboot on ipq806x (EA8500): msm_read_ti...TrunkUnconfirmed Task Description

This happened on OpenWrt SNAPSHOT r13520-68b94f0fb4, but it’s pretty random. I haven’t been able to figure out what causes it. It usually happens at least once within a week. I’m not sure why there’s no call stack here, I also tried `cat /sys/kernel/debug/crashlog` a few hours after it happened and got a “No such file or directory”.

# uname -a
Linux EA8500S 5.4.43 #0 SMP Mon Jun 8 19:16:17 2020 armv7l GNU/Linux


[333045.256692] 8<--- cut here ---
[333045.256733] Unable to handle kernel NULL pointer dereference at virtual address 0000000a
[333045.258656] pgd = 8948efb0
[333045.267139] [0000000a] *pgd=00000000
[333045.269709] Internal error: Oops: 5 [#1] SMP ARM
[333045.273404] Modules linked in: nf_flow_table_ipv6 nf_flow_table_ipv4 nf_flow_table_inet ath10k_pci ath10k_core ath nft_reject_ipv6 nft_reject_ipv4 nft_reject_inet nft_reject nft_redir nft_quota nft_objref nft_numgen nft_nat nft_masq nft_log nft_limit nft_hash nft_flow_offload nft_ct nft_counter nf_tables_set nf_tables nf_conntrack_netlink mac80211 iptable_nat ipt_REJECT cfg80211 xt_time xt_tcpudp xt_tcpmss xt_statistic xt_state xt_recent xt_policy xt_nat xt_multiport xt_mark xt_mac xt_limit xt_length xt_hl xt_helper xt_esp xt_ecn xt_dscp xt_conntrack xt_connmark xt_connlimit xt_connbytes xt_comment xt_TCPMSS xt_REDIRECT xt_NETMAP xt_MASQUERADE xt_LOG xt_HL xt_FLOWOFFLOAD xt_DSCP xt_CT xt_CLASSIFY ts_fsm ts_bm nfnetlink nf_reject_ipv4 nf_nat_tftp nf_nat_snmp_basic nf_nat_sip nf_nat_rtsp nf_nat_pptp nf_nat_irc nf_nat_h323 nf_nat_ftp nf_nat_amanda nf_nat nf_log_ipv4 nf_flow_table_hw nf_flow_table nf_conntrack_tftp nf_conntrack_snmp nf_conntrack_sip nf_conntrack_rtsp nf_conntrack_rtcache
[333045.273734]  nf_conntrack_pptp nf_conntrack_irc nf_conntrack_h323 nf_conntrack_ftp nf_conntrack_broadcast ts_kmp nf_conntrack_amanda nf_conncount iptable_raw iptable_mangle iptable_filter ipt_ah ipt_ECN ip_tables compat asn1_decoder fuse act_connmark nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 sch_tbf sch_ingress sch_htb sch_hfsc em_u32 cls_u32 cls_tcindex cls_route cls_matchall cls_fw cls_flow cls_basic act_skbedit act_mirred ledtrig_usbport ledtrig_heartbeat nf_log_ipv6 nf_log_common ip6table_mangle ip6table_filter ip6_tables ip6t_REJECT x_tables nf_reject_ipv6 ifb ipcomp6 xfrm6_tunnel esp6 ah6 xfrm4_tunnel ipcomp esp4 ah4 tunnel6 tunnel4 tun xfrm_user xfrm_ipcomp af_key xfrm_algo vfat fat ntfs nls_utf8 nls_iso8859_1 nls_cp437 sha1_generic md5 echainiv des_generic libdes cbc authenc usb_storage leds_gpio xhci_plat_hcd xhci_pci xhci_hcd dwc3 dwc3_qcom ohci_platform ohci_hcd phy_qcom_dwc3 ahci fsl_mph_dr_of ehci_platform ehci_fsl sd_mod ahci_platform libahci_platform libahci libata scsi_mod
[333045.343201]  ehci_hcd gpio_button_hotplug ext4 mbcache jbd2 exfat(C) crc32c_generic
[333045.452936] CPU: 0 PID: 10391 Comm: kworker/0:2 Tainted: G         C        5.4.43 #0
[333045.460735] Hardware name: Generic DT based system
[333045.468481] Workqueue: events dbs_work_handler
[333045.473245] PC is at msm_read_timer_count+0xc/0x18
[333045.477746] LR is at msm_read_current_timer+0x1c/0x28
[333045.482608] pc : [<c0733ea8>]    lr : [<c0733ee4>]    psr: a0000013
[333045.487814] sp : da0f1dc0  ip : 00000000  fp : dce52880
[333045.494327] r10: ddb8d010  r9 : dd648b40  r8 : 16e36000
[333045.499619] r7 : dd511240  r6 : 00000006  r5 : 00000001  r4 : c0c68ea0
[333045.504919] r3 : 00000006  r2 : 1fffa6f0  r1 : 20000013  r0 : c0c28428
[333045.511261] Flags: NzCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment none
20.06.20203195Base systemBug ReportVery LowHighramips/mt7621/zbt3526 -> boot failure with kernel 5.4TrunkUnconfirmed Task Description

Supply the following if possible:
- Device problem occurs on: ZBT 3526-16MB + 32 MB - Software versions of OpenWrt/LEDE: current trunk (kernel 5.4)
- Steps to reproduce: when i update the firmware, i see that there is a network after reboot for ~10sec, and then it is gone, and is not accessable, seeems to be, that something is crashing.
i can only hard-reset - nothing else.

any idea ?
maybe it is related also like the other bugs reported ? for bootloop or hanging/crashing mt7621 ?

 


26.06.20203204KernelBug ReportVery LowHighmac80211 crashTrunkUnconfirmed Task Description

Netgear R7800 running hnyman’s build master-r13625-d4dea7efcd-20200624-ath10k

[104369.085841] ------------[ cut here ]------------
[104369.091780] WARNING: CPU: 0 PID: 0 at backports-5.7-rc3-1/net/mac80211/sta_info.c:1929 ieee80211_sta_update_pending_airtime+0x1f8/0x1fc [mac80211]
[104369.096329] STA f0:18:xxxxx AC 2 txq pending airtime underflow: 4294967244, 52
[104369.096332] Modules linked in: pppoe ppp_async ath10k_pci ath10k_core ath pptp pppox ppp_mppe ppp_generic mac80211 ipt_REJECT cfg80211 xt_time xt_tcpudp xt_tcpmss xt_statistic xt_state xt_recent xt_nat xt_multiport xt_mark xt_mac xt_limit xt_length xt_hl xt_helper xt_esp xt_ecn xt_dscp xt_conntrack xt_connmark xt_connlimit xt_connbytes xt_comment xt_TCPMSS xt_REDIRECT xt_MASQUERADE xt_LOG xt_HL xt_FLOWOFFLOAD xt_DSCP xt_CT xt_CLASSIFY wireguard slhc sch_cake nf_reject_ipv4 nf_log_ipv4 nf_flow_table_hw nf_flow_table nf_conntrack_rtcache nf_conntrack_netlink nf_conncount iptable_raw iptable_nat iptable_mangle iptable_filter ipt_ah ipt_ECN ip_tables crc_ccitt compat chaoskey fuse sch_tbf sch_ingress sch_htb sch_hfsc em_u32 cls_u32 cls_tcindex cls_route cls_matchall cls_fw cls_flow cls_basic act_skbedit act_mirred ledtrig_usbport ledtrig_heartbeat xt_set ip_set_list_set ip_set_hash_netportnet ip_set_hash_netport ip_set_hash_netnet ip_set_hash_netiface ip_set_hash_net ip_set_hash_mac
[104369.109593]  ip_set_hash_ipportnet ip_set_hash_ipportip ip_set_hash_ipport ip_set_hash_ipmark ip_set_hash_ip ip_set_bitmap_port ip_set_bitmap_ipmac ip_set_bitmap_ip ip_set nfnetlink ip6table_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 ip6t_NPT nf_log_ipv6 nf_log_common ip6table_mangle ip6table_filter ip6_tables ip6t_REJECT x_tables nf_reject_ipv6 msdos ip_gre gre ifb ip6_udp_tunnel udp_tunnel sit tunnel4 ip_tunnel tun vfat fat hfsplus cifs nls_utf8 nls_iso8859_15 nls_iso8859_1 nls_cp850 nls_cp437 nls_cp1250 sha1_generic md5 md4 ecb des_generic libdes arc4 usb_storage leds_gpio xhci_plat_hcd xhci_pci xhci_hcd dwc3 dwc3_qcom ohci_platform ohci_hcd phy_qcom_dwc3 ahci fsl_mph_dr_of ehci_platform ehci_fsl sd_mod ahci_platform libahci_platform libahci libata scsi_mod ehci_hcd gpio_button_hotplug ext4 mbcache jbd2 exfat(C) crc32c_generic
[104369.256372] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G         C        5.4.48 #0
[104369.278522] Hardware name: Generic DT based system
[104369.286004] [<c030f954>] (unwind_backtrace) from [<c030b96c>] (show_stack+0x14/0x20)
[104369.290607] [<c030b96c>] (show_stack) from [<c08ba2e0>] (dump_stack+0x94/0xa8)
[104369.298594] [<c08ba2e0>] (dump_stack) from [<c031e7b4>] (__warn+0xb4/0xd0)
[104369.305702] [<c031e7b4>] (__warn) from [<c031e850>] (warn_slowpath_fmt+0x80/0x90)
[104369.312720] [<c031e850>] (warn_slowpath_fmt) from [<bf691af0>] (ieee80211_sta_update_pending_airtime+0x1f8/0x1fc [mac80211])
[104369.320482] [<bf691af0>] (ieee80211_sta_update_pending_airtime [mac80211]) from [<bf68d734>] (ieee80211_tx_monitor+0xe38/0x10c0 [mac80211])
[104369.331785] [<bf68d734>] (ieee80211_tx_monitor [mac80211]) from [<bf68da18>] (ieee80211_tx_status+0x5c/0x6c [mac80211])
[104369.344456] [<bf68da18>] (ieee80211_tx_status [mac80211]) from [<bf7588e4>] (ath10k_txrx_tx_unref+0x130/0x318 [ath10k_core])
[104369.355280] [<bf7588e4>] (ath10k_txrx_tx_unref [ath10k_core]) from [<bf755264>] (ath10k_htt_txrx_compl_task+0x7d0/0x1058 [ath10k_core])
[104369.366428] [<bf755264>] (ath10k_htt_txrx_compl_task [ath10k_core]) from [<bf7a3b3c>] (ath10k_pci_napi_poll+0x58/0x11c [ath10k_pci])
[104369.378748] [<bf7a3b3c>] (ath10k_pci_napi_poll [ath10k_pci]) from [<c0773a2c>] (net_rx_action+0x118/0x374)
[104369.390603] [<c0773a2c>] (net_rx_action) from [<c0302298>] (__do_softirq+0x130/0x2d4)
[104369.400148] [<c0302298>] (__do_softirq) from [<c0322c10>] (irq_exit+0xbc/0xe0)
[104369.408132] [<c0322c10>] (irq_exit) from [<c036d150>] (__handle_domain_irq+0x6c/0xd0)
[104369.415343] [<c036d150>] (__handle_domain_irq) from [<c05c6774>] (gic_handle_irq+0x5c/0xb8)
[104369.423324] [<c05c6774>] (gic_handle_irq) from [<c0301a8c>] (__irq_svc+0x6c/0x90)
[104369.431910] Exception stack(0xc0c01ee0 to 0xc0c01f28)
[104369.439303] 1ee0: 00000000 00005eec 1ce52000 dd991a00 dcc2d400 00000000 dd990df0 00005eec
[104369.444430] 1f00: 00005eec 00000000 524739a0 5244a280 00000015 c0c01f30 c0716b90 c0716b94
[104369.452661] 1f20: 20000013 ffffffff
[104369.460907] [<c0301a8c>] (__irq_svc) from [<c0716b94>] (cpuidle_enter_state+0x94/0x498)
[104369.464643] [<c0716b94>] (cpuidle_enter_state) from [<c0716fdc>] (cpuidle_enter+0x30/0x4c)
[104369.472716] [<c0716fdc>] (cpuidle_enter) from [<c034a7ec>] (do_idle+0x1d8/0x240)
[104369.480787] [<c034a7ec>] (do_idle) from [<c034aafc>] (cpu_startup_entry+0x1c/0x20)
[104369.488425] [<c034aafc>] (cpu_startup_entry) from [<c0b00e58>] (start_kernel+0x4d8/0x4e8)
[104369.495990] ---[ end trace 713bf4bd85eb5631 ]---
27.06.20203207Base systemBug ReportVery LowHighSetting MTU on Bridged interfaces does not set MTU on m...openwrt-19.07Unconfirmed Task Description

- Device problem occurs on - x86
- Software versions of OpenWrt/LEDE release, packages, etc. - 19.07.3

 

I think it’s a bug/overlooked use case, but when you have interfaces bridged in the UCI config, the MTU setting does not get applied to the member interfaces (physical or VLAN).

config interface 'lan'
        option proto 'static'
        option netmask '255.255.255.0'
        option ip6assign '60'
        option ipaddr '192.168.1.1'
        option type 'bridge'
        option mtu '9000'
        option ifname 'eth1 eth4.10'

When I boot using this config I have connectivity issues with devices using Jumbo frames. ifconfig confirms that MTUs on the members interfaces are still at default 1500.

eth1      Link encap:Ethernet  HWaddr 0C:C4:7A:AB:39:3D
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Memory:df440000-df45ffff

eth4      Link encap:Ethernet  HWaddr 3C:FD:FE:BB:01:50
          inet6 addr: fe80::3efd:feff:febb:150/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500 Metric:1
          RX packets:50176 errors:0 dropped:1 overruns:0 frame:0
          TX packets:37468 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:15692679 (14.9 MiB)  TX bytes:29263711 (27.9 MiB)

eth4.10   Link encap:Ethernet  HWaddr 3C:FD:FE:BB:01:50
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:36728 errors:0 dropped:0 overruns:0 frame:0
          TX packets:20850 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:9314410 (8.8 MiB)  TX bytes:26473088 (25.2 MiB)

I have to manually use the ifconfig tool to set the MTU (i.e. ifconfig eth4.10 mtu 9000) to get the network back up and running correctly.

Obviously these commands could be scritped, however it was my understanding the UCI network config should be doing this .

02.07.20203213KernelBug ReportVery LowHighLantiq-XRX200: Fritzbox 7360 SL PCie Link up failes! - ...TrunkUnconfirmed Task Description

On my Lantiq-XRX200 device Fritzbox 7360 SL, the WIFI PHy doesnt gets detected anymore. right after 1 second when booting the device. i get a kernel warning that the “PCIe PHY cant get detected and right after that 5 lines of
“PCIe phy_link_up timeout”

This happend in release of 19.07.x and trunk.

 

[ 0.864077] ifx_pcie_wait_phy_link_up timeout
[ 1.081343] ifx_pcie_wait_phy_link_up timeout
[ 1.298569] ifx_pcie_wait_phy_link_up timeout
[ 1.302795] pcie_rc_initialize link up failed!!!!!

18.07.20203237PackagesBuild FailureVery LowHighumdns: fails to compile with gcc10TrunkUnconfirmed Task Description

Try to compile umdns with gcc10 and it will break with following error:

service.c:240:10: error: ‘strcpy’ offset 6 from the object at ‘b’ is
out of the bounds of referenced subobject ‘name’ with type ‘uint8_t[]’ {aka ‘unsigned char[]’} at offset 6 [-Werror=array-bounds]

More detailed error:
https://github.com/berlin-open-wireless-lab/DAWN/issues/109#issuecomment-657483908

22.07.20203242Base systemBug ReportVery LowHighUAS not working - All devices with USB3.0 affectedAllUnconfirmed Task Description

USB controller “f10f8000.usb3” is preventing UAS from working on OpenWRT devices, as dmesg states:

[ 1.830001] usb 3-1: new SuperSpeed USB device number 2 using xhci-hcd
[ 1.860632] usb 3-1: USB controller f10f8000.usb3 does not support streams, which are required by the UAS driver.
[ 1.870949] usb 3-1: Please try an other USB controller if you wish to use UAS.
[ 1.878291] usb-storage 3-1:1.0: USB Mass Storage device detected

Checked in OpenWRT 18.04 and 19.03 with Linksys WRT3200ACM and Turris Omnia. This impacts USB3.0 speeds.

To reproduce just hook up a USB3.0 HDD to a OpenWRT device on the USB3.0 port and see dmesg.

Is it possible to try another controller or fix f10f8000.usb3?

Showing tasks 151 - 200 of 1150 Page 4 of 23<<First - 2 - 3 - 4 - 5 - 6 - Last >>

Available keyboard shortcuts

Tasklist

Task Details

Task Editing