OpenWrt/LEDE Project

Welcome to the OpenWrt Project bug reporting and issue tracking system

Problems to be reported here are for the current OpenWrt and legacy LEDE Project’s targets, sources, toolchain, core packages, build procedures, distribution and infrastructure. Guidelines for submitting a good bug report can be found at the OpenWrt Project website. Problems related to LuCI or OpenWrt packages need to be reported in their repositories:

Notifications of all submissions and task changes are sent to openwrt-bugs@infradead.org.

OpenedIDCategory  ascTask TypePrioritySeveritySummaryReported InStatus
30.01.20202783Base systemBug ReportVery LowHighTP-Link Archer A7 v5 can't be flashet via tftpopenwrt-19.07Unconfirmed Task Description

Device: TP-Link Archer A7 (RU) Ver 5.0
Software: OpenWRT 19.07.0

I just bought this router. And I trying to flash it with openwrt-19.07.0-ath79-generic-tplink_archer-a7-v5-squashfs-factory.bin trough tftp.
In wireshark I clearly see that file was downloaded. But router didn’t flashed.
I tried to flash snapshot image wtih same result.
I checked sha256 sums and it matches.

When I reproduced same steps with original TP-Link update image it worked well. Seems like something prevents router from flashing OpenWRT image.

30.01.20202785Base systemBug ReportVery LowHighkernel loading during netboot fails on mikrotik devicesopenwrt-19.07Unconfirmed Task Description

Devices tested:

  • Mikrotik rb433
  • Mikrotik rb435g

Software version: Using the v19.07.1 tag.

Issue: There are a few packages, whose are leading the ramdisk “unbbotable”, more precise the device is not able to load the kernel. First this happened by kmod-scsi-core , I thought it must be some kernel-related issue. Afterthat I realised that either I enable the aforementioned kernel-module, or the libraries called libpcre and libpci, the boot procedure will stop at:

Gateway: 192.168.1.254
transfer started ................................... transfer ok, time=2.61s
setting up elf image... OK
jumping to kernel code OpenWrt kernel loader for AR7XXX/AR9XXX
Copyright (C) 2011 Gabor Juhos juhosg@openwrt.org Decompressing kernel... done!
Starting kernel at 80060000...

Compiling these packages only as a module results a nice bootable image. Firstly I thought that maybe my ramdisk is too large, but it is about only 4,5 MB - previously using older trunk I was able to boot up images over 5 MByte.
I have pasted the config file to the ticket. If you switch libpcre and libpci to M instead of * it will boot.

This issue was not there before, using the image built from 18.06.

31.01.20202791Base systemBug ReportVery LowHighIPv6 router advertisments lost after upgrade to 19.07openwrt-19.07Unconfirmed Task Description

I’ve just upgraded my linksys wrt-1200ac from 18.06.4 to 19.07.0

I’ve got a more-or-less out-of-the-box configuration with wired and wireless clients all connected to the ‘br-lan’ bridge. My ISP provides native IPv6. I’ve got odhcpd-ip6only installed, and a mixture of clients, some using SLAAC and some using DHCPv6.

When a wireless client that is configured for SLAAC (e.g. an android phone) connects, it sends an IPv6 router solicitation to ff02::1 and receives a router advertisement on its fe80::<something> address. That still works fine. But the client never receives any further router adverts, so the route times out after 1800 seconds and IPv6 connectivity is lost.

This is *only* going wrong with wireless clients: tcpdump on a wired client shows router adverts arriving on ff02::1 every few minutes. But tcpdump on a wireless client shows no router adverts after the initial one.

I’ve retested with 18.06.4 and the problem does not exist in that version.

16.02.20202835Base systemBug ReportVery LowHighMT7621: Clients disconnects.openwrt-19.07Unconfirmed Task Description

Hi! I have MT7621 and when to router connected more than 10 peoples router start disconnecting some peoples(have two networks guest and main on 2,4).

There is my settings:
config wifi-iface ‘default_radio0’ option device ‘radio0’ option network ‘lan’ option mode ‘ap’ option wpa_disable_eapol_key_retries ‘1’ option key ‘WIFIPASS’ option ssid ‘WIFINAME’ option encryption ‘psk2+ccmp’ option disassoc_low_ack ‘0’ (guest network have same settings)

Other info:
Newifi-D2
MediaTek MT7621 ver:1 eco:3
OpenWrt 19.07.1 r10911-c155900f66 / LuCI openwrt-19.07 branch git-20.045.27998-49999e9

I also noticed that before the client is disconnected from the network, it will lose the Internet.

 

Issue on github: https://github.com/openwrt/mt76/issues/358

Many peoples with Newifi3 D2 have same problem(in github links and more details).

PLEASE, FIX IT!

18.02.20202844Base systemBug ReportVery LowHighath10k on archer C7 v2: high latencyopenwrt-19.07Unconfirmed Task Description

On my Archer C7 v2, since the upgrade from 18.06 to 19.07, I sometimes get very high latency on my 5 GHz wifi network:

This is when pinging a wireless client from the router itself.

ping 192.168.12.167
PING 192.168.12.167 (192.168.12.167): 56 data bytes
64 bytes from 192.168.12.167: seq=0 ttl=64 time=1.334 ms
64 bytes from 192.168.12.167: seq=1 ttl=64 time=2.002 ms
64 bytes from 192.168.12.167: seq=2 ttl=64 time=1004.448 ms
64 bytes from 192.168.12.167: seq=3 ttl=64 time=4.342 ms
64 bytes from 192.168.12.167: seq=4 ttl=64 time=1.072 ms
64 bytes from 192.168.12.167: seq=5 ttl=64 time=2.074 ms
64 bytes from 192.168.12.167: seq=6 ttl=64 time=2.505 ms
64 bytes from 192.168.12.167: seq=7 ttl=64 time=1.059 ms
64 bytes from 192.168.12.167: seq=8 ttl=64 time=1.746 ms
64 bytes from 192.168.12.167: seq=9 ttl=64 time=1.176 ms
64 bytes from 192.168.12.167: seq=10 ttl=64 time=1.086 ms
64 bytes from 192.168.12.167: seq=11 ttl=64 time=1.072 ms
64 bytes from 192.168.12.167: seq=12 ttl=64 time=815.290 ms
64 bytes from 192.168.12.167: seq=13 ttl=64 time=1004.417 ms
64 bytes from 192.168.12.167: seq=14 ttl=64 time=4.294 ms
64 bytes from 192.168.12.167: seq=15 ttl=64 time=4.520 ms
64 bytes from 192.168.12.167: seq=16 ttl=64 time=1003.250 ms
64 bytes from 192.168.12.167: seq=17 ttl=64 time=3.125 ms
64 bytes from 192.168.12.167: seq=18 ttl=64 time=1.019 ms
64 bytes from 192.168.12.167: seq=19 ttl=64 time=2.066 ms
^C
--- 192.168.12.167 ping statistics ---
20 packets transmitted, 20 packets received, 0% packet loss
round-trip min/avg/max = 1.019/193.094/1004.448 ms

The upgrade to 19.07.1 didn’t solve the issue. What (temporarily) seem to work is to restart the wlan0 interface. After a few hours the problem comes back. The client is very close to the AP (less than 3 meters, although there is a floor between). Signal quality is reported as very good.

Station 54:60:09:d3:e4:d6 (on wlan0)
        inactive time:  540 ms
        rx bytes:       1082546
        rx packets:     6294
        tx bytes:       15523400
        tx packets:     11636
        tx retries:     0
        tx failed:      1
        rx drop misc:   0
        signal:         -66 [-76, -68, -71] dBm
        signal avg:     -62 [-72, -64, -67] dBm
        tx bitrate:     390.0 MBit/s VHT-MCS 8 80MHz short GI VHT-NSS 1
        rx bitrate:     390.0 MBit/s VHT-MCS 8 80MHz short GI VHT-NSS 1
        rx duration:    422088 us
        last ack signal:-95 dBm
        authorized:     yes
        authenticated:  yes
        associated:     yes
        preamble:       long
        WMM/WME:        yes
        MFP:            no
        TDLS peer:      no
        DTIM period:    2
        beacon interval:100
        short slot time:yes
        connected time: 447 seconds

I am using stock 19.07.1 firmware. I also tried changing the regulatory domain from CA to US but it didn’t help.
I will now try with the non-ct driver and firmware to see if it helps, as it worked fine on 18.06 which didn’t include the -ct firmware by default.

cat /etc/config/wireless

config wifi-device 'radio0'
        option type 'mac80211'
        option hwmode '11a'
        option path 'pci0000:00/0000:00:00.0'
        option htmode 'VHT80'
        option noscan '1'
        option country 'US'
        option channel '149'

config wifi-iface 'default_radio0'
        option device 'radio0'
        option key 'removed'
        option network 'lan'
        option mode 'ap'
        option ssid 'myssid5'
        option encryption 'psk2+ccmp'

config wifi-device 'radio1'
        option type 'mac80211'
        option channel '11'
        option hwmode '11g'
        option path 'platform/ahb/ahb:apb/18100000.wmac'
        option noscan '1'
#       option country 'CA'
        option htmode 'HT40'
        option require_mode 'g'

config wifi-iface 'default_radio1'
        option device 'radio1'
        option network 'lan'
        option mode 'ap'
        option ssid 'myssid'
        option encryption 'psk2+ccmp'
        option key 'removed'
        option ieee80211w '1'
21.02.20202847Base systemBug ReportVery LowHighbetween ath79-master-r12157-a1cfe0dcbb and ath79-master...TrunkUnconfirmed Task Description

Supply the following if possible:
- Device problem occurs on
Netgear WNDR3700v2

- Software versions of OpenWrt/LEDE release, packages, etc.

between ath79-master-r12157-a1cfe0dcbb and ath79-master-r12259 including the rename from wndr3700v2 to wndr3700-v2 OpenWrt lost its capability to detect the two radios.

- Steps to reproduce

 


root@router:/tmp# cat /etc/banner

_______                     ________        __

| |.—–.—–.—–.| | | |.—-.| |_
| - || _ | -| || | | || _|| _|
|
_|| |_||||||| ||

        |__| W I R E L E S S   F R E E D O M

—————————————————– OpenWrt SNAPSHOT, r12157-a1cfe0dcbb


root@router:/tmp# dmesg
[ 0.000000] Linux version 4.19.98 (moeller@work-horse) (gcc version 8.3.0 (OpenWrt GCC 8.3.0 r12053-9e799f3eee)) #0 Fri Jan 31 22:29:40 2020
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
[ 0.000000] MIPS: machine is Netgear WNDR3700v2
[ 0.000000] SoC: Atheros AR7161 rev 2
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0×0000000000000000-0x0000000003ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0×0000000000000000-0x0000000003ffffff]
[ 0.000000] Initmem setup node 0 [mem 0×0000000000000000-0x0000000003ffffff]
[ 0.000000] On node 0 totalpages: 16384
[ 0.000000] Normal zone: 144 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 16384 pages, LIFO batch:3
[ 0.000000] random: get_random_bytes called from start_kernel+0×98/0x4a8 with crng_init=0
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16240
[ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 57516K/65536K available (4327K kernel code, 176K rwdata, 1020K rodata, 1188K init, 206K bss, 8020K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 51
[ 0.000000] CPU clock: 680.000 MHz [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 5621354254 ns
[ 0.000008] sched_clock: 32 bits at 340MHz, resolution 2ns, wraps every 6316128254ns
[ 0.007800] Calibrating delay loop... 452.19 BogoMIPS (lpj=2260992)
[ 0.074071] pid_max: default: 32768 minimum: 301
[ 0.078916] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.085519] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.096880] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.106751] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.112960] pinctrl core: initialized pinctrl subsystem
[ 0.119019] NET: Registered protocol family 16
[ 0.428745] PCI host bridge /ahb/apb/pcie-controller@17010000 ranges:
[ 0.435198] MEM 0×0000000010000000..0x0000000016ffffff
[ 0.440426] IO 0×0000000000000000..0×0000000000000000 [ 0.463018] PCI host bridge to bus 0000:00
[ 0.467126] pci_bus 0000:00: root bus resource [mem 0×10000000-0x16ffffff]
[ 0.474044] pci_bus 0000:00: root bus resource [io 0×0000]
[ 0.479604] pci_bus 0000:00: root bus resource [??? 0×00000000 flags 0×0]
[ 0.486385] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.494769] pci 0000:00:11.0: [168c:ff1d] type 00 class 0×020000 [ 0.494800] pci 0000:00:11.0: reg 0×10: [mem 0×00000000-0x0000ffff]
[ 0.495095] pci 0000:00:12.0: [168c:ff1d] type 00 class 0×020000 [ 0.495122] pci 0000:00:12.0: reg 0×10: [mem 0×00000000-0x0000ffff]
[ 0.495679] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 0.495708] pci 0000:00:11.0: BAR 0: assigned [mem 0×10000000-0x1000ffff]
[ 0.502528] pci 0000:00:12.0: BAR 0: assigned [mem 0×10010000-0x1001ffff]
[ 0.512297] clocksource: Switched to clocksource MIPS
[ 0.518346] NET: Registered protocol family 2
[ 0.523491] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes)
[ 0.531183] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.538204] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.544573] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.551058] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.556944] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.563492] NET: Registered protocol family 1
[ 0.567890] PCI: CLS 0 bytes, default 32
[ 0.570473] Crashlog allocated RAM at address 0x3f00000
[ 0.576987] workingset: timestamp_bits=14 max_order=14 bucket_order=0
[ 0.589206] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.595083] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) © 2001-2006 Red Hat, Inc.
[ 0.615469] io scheduler noop registered
[ 0.619388] io scheduler deadline registered (default)
[ 0.625206] ar7100-usb-phy 18030000.usb-phy: phy reset is missing
[ 0.632106] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.639111] console [ttyS0] disabled
[ 0.642766] 18020000.uart: ttyS0 at MMIO 0×18020000 (irq = 10, base_baud = 10625000) is a 16550A
[ 0.651550] console [ttyS0] enabled
[ 0.658520] bootconsole [early0] disabled
[ 0.672685] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
[ 0.677766] 4 fixed-partitions partitions found on MTD device spi0.0
[ 0.684156] Creating 4 MTD partitions on “spi0.0”:
[ 0.688944] 0×000000000000-0×000000050000 : “u-boot” [ 0.694662] 0×000000050000-0×000000070000 : “u-boot-env” [ 0.700642] 0×000000070000-0x000000ff0000 : “firmware” [ 0.709051] 2 netgear-fw partitions found on MTD device firmware
[ 0.715111] Creating 2 MTD partitions on “firmware”:
[ 0.720073] 0×000000000000-0x0000001c4440 : “kernel” [ 0.725799] 0x0000001c4440-0x000000f80000 : “rootfs” [ 0.731378] mtd: device 4 (rootfs) set to be root filesystem
[ 0.738413] 1 squashfs-split partitions found on MTD device rootfs
[ 0.744648] 0x0000007b0000-0x000000f80000 : “rootfs_data” [ 0.750780] 0x000000ff0000-0×000001000000 : “art” [ 0.756658] Realtek RTL8366S ethernet switch driver version 0.2.2
[ 0.762862] rtl8366s rtl8366s: cannot find mdio node phandle
[ 0.768528] rtl8366s rtl8366s: using GPIO pins 5 (SDA) and 7 (SCK)
[ 0.774813] rtl8366s rtl8366s: RTL8366 ver. 1 chip found
[ 0.826529] libphy: rtl8366s: probed
[ 0.831545] libphy: Fixed MDIO Bus: probed
[ 1.184018] ag71xx 19000000.eth: connected to PHY at fixed-0:00 [uid=00000000, driver=Generic PHY]
[ 1.193617] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode: rgmii
[ 1.533893] ag71xx 1a000000.eth: connected to PHY at rtl8366s:04 [uid=001cc960, driver=Generic PHY]
[ 1.543585] eth1: Atheros AG71xx at 0xba000000, irq 5, mode: rgmii
[ 1.552067] NET: Registered protocol family 10
[ 1.561269] Segment Routing with IPv6
[ 1.565090] NET: Registered protocol family 17
[ 1.569586] 8021q: 802.1Q VLAN Support v1.8
[ 1.585516] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[ 1.596158] Freeing unused kernel memory: 1188K
[ 1.600682] This architecture does not have kernel memory protection.
[ 1.607138] Run /sbin/init as init process
[ 2.582308] random: fast init done
[ 2.807119] init: Console is alive
[ 2.810741] init: - watchdog -
[ 6.241610] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 6.383455] usbcore: registered new interface driver usbfs
[ 6.389022] usbcore: registered new interface driver hub
[ 6.394453] usbcore: registered new device driver usb
[ 6.430284] ehci_hcd: USB 2.0 ‘Enhanced’ Host Controller (EHCI) Driver
[ 6.445010] SCSI subsystem initialized
[ 6.453749] ehci-platform: EHCI generic platform driver
[ 7.058167] ehci-platform 1b000000.usb: EHCI Host Controller
[ 7.063869] ehci-platform 1b000000.usb: new USB bus registered, assigned bus number 1
[ 7.071783] ehci-platform 1b000000.usb: irq 3, io mem 0x1b000000
[ 7.102319] ehci-platform 1b000000.usb: USB 2.0 started, EHCI 1.00
[ 7.109300] hub 1-0:1.0: USB hub found
[ 7.113454] hub 1-0:1.0: 2 ports detected
[ 7.120810] ohci_hcd: USB 1.1 ‘Open’ Host Controller (OHCI) Driver
[ 7.128705] ohci-platform: OHCI generic platform driver
[ 7.134182] ohci-platform 1c000000.usb: Generic Platform OHCI controller
[ 7.140911] ohci-platform 1c000000.usb: new USB bus registered, assigned bus number 2
[ 7.148855] ohci-platform 1c000000.usb: irq 14, io mem 0x1c000000
[ 7.227154] hub 2-0:1.0: USB hub found
[ 7.231244] hub 2-0:1.0: 2 ports detected
[ 7.239911] usbcore: registered new interface driver usb-storage
[ 7.246968] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 7.257068] init: - preinit -
[ 7.952485] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 8.224006] usb-storage 1-1:1.0: USB Mass Storage device detected
[ 8.239044] scsi host0: usb-storage 1-1:1.0
[ 8.607425] random: procd: uninitialized urandom read (4 bytes read)
[ 9.217736] random: jshn: uninitialized urandom read (4 bytes read)
[ 9.313323] scsi 0:0:0:0: Direct-Access SanDisk Ultra 1.01 PQ: 0 ANSI: 2
[ 9.324268] sd 0:0:0:0: [sda] 31266816 512-byte logical blocks: (16.0 GB/14.9 GiB)
[ 9.435234] sd 0:0:0:0: [sda] Write Protect is off
[ 9.440027] sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00
[ 9.441159] sd 0:0:0:0: [sda] No Caching mode page found
[ 9.446536] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 9.467635] sda: sda1 sda2
[ 9.485172] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 9.512732] random: jshn: uninitialized urandom read (4 bytes read)
[ 9.803851] random: jshn: uninitialized urandom read (4 bytes read)
[ 9.855143] random: jshn: uninitialized urandom read (4 bytes read)
[ 9.937787] random: jshn: uninitialized urandom read (4 bytes read)
[ 10.734464] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 11.792658] eth0: link up (1000Mbps/Full duplex)
[ 11.797336] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 21.002121] mount_root: loading kmods from internal overlay
[ 21.065763] kmodloader: loading kernel modules from etc/modules-boot.d/*
[ 21.074086] kmodloader: done loading kernel modules from
etc/modules-boot.d/*
[ 22.067245] jffs2: notice: (573) jffs2_build_xattr_subsystem: complete building xattr subsystem, 4 of xdatum (3 unchecked, 1 orphan) and 38 of xref (1 dead, 0 orphan) found.
[ 22.083539] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 22.104478] block: extroot: not configured
[ 22.493615] jffs2: notice: (571) jffs2_build_xattr_subsystem: complete building xattr subsystem, 4 of xdatum (3 unchecked, 1 orphan) and 38 of xref (1 dead, 0 orphan) found.
[ 22.512972] mount_root: loading kmods from internal overlay
[ 22.571532] kmodloader: loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
[ 22.586940] kmodloader: done loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
[ 23.297496] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 23.311711] block: extroot: not configured
[ 23.317033] mount_root: switching to jffs2 overlay
[ 23.391179] overlayfs: upper fs does not support tmpfile.
[ 23.402971] urandom-seed: Seeding with /etc/urandom.seed
[ 23.506382] eth0: link down
[ 23.522968] procd: - early -
[ 23.525956] procd: - watchdog -
[ 24.224357] procd: - watchdog -
[ 24.227866] procd: - ubus -
[ 24.305816] urandom_read: 2 callbacks suppressed
[ 24.305823] random: ubusd: uninitialized urandom read (4 bytes read)
[ 24.321238] random: ubusd: uninitialized urandom read (4 bytes read)
[ 24.330097] procd: - init -
[ 25.653767] kmodloader: loading kernel modules from /etc/modules.d/*
[ 25.815614] ntfs: driver 2.1.32 [Flags: R/O MODULE].
[ 25.855111] tun: Universal TUN/TAP device driver, 1.6
[ 25.878662] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 25.922686] gre: GRE over IPv4 demultiplexor driver
[ 25.944224] ip_gre: GRE over IPv4 tunneling driver
[ 26.291706] Mirror/redirect action on
[ 26.325462] u32 classifier
[ 26.328171] input device check on
[ 26.331822] Actions configured
[ 26.380723] Loading modules backported from Linux version v5.4-rc8-0-gaf42d3466bdc
[ 26.388336] Backport generated by backports.git v5.4-rc8-1-0-g368e8c51
[ 26.401462] urngd: v1.0.2 started.
[ 26.492389] usbcore: registered new interface driver usbserial_generic
[ 26.498978] usbserial: USB Serial support registered for generic
[ 26.558787] wireguard: WireGuard 0.0.20200128 loaded. See www.wireguard.com for information.
[ 26.567273] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld Jason@zx2c4.com. All Rights Reserved.
[ 26.778103] xt_time: kernel timezone is -0000
[ 26.798642] ath9k_pci_owl_loader 0000:00:11.0: enabling device (0000 → 0002)
[ 26.806040] ath9k_pci_owl_loader 0000:00:12.0: enabling device (0000 → 0002)
[ 26.824088] ath9k_pci_owl_loader 0000:00:12.0: fixup device configuration
[ 26.832789] ath9k_pci_owl_loader 0000:00:11.0: fixup device configuration
[ 26.861449] pci 0000:00:12.0: [168c:0029] type 00 class 0×028000 [ 26.861487] pci 0000:00:12.0: reg 0×10: [mem 0×10010000-0x1001ffff]
[ 26.861542] pci 0000:00:12.0: PME# supported from D0 D3hot
[ 26.862141] pci 0000:00:12.0: BAR 0: assigned [mem 0×10010000-0x1001ffff]
[ 26.877545] pci 0000:00:11.0: [168c:0029] type 00 class 0×028000 [ 26.877582] pci 0000:00:11.0: reg 0×10: [mem 0×10000000-0x1000ffff]
[ 26.877638] pci 0000:00:11.0: PME# supported from D0 D3hot
[ 26.878247] pci 0000:00:11.0: BAR 0: assigned [mem 0×10000000-0x1000ffff]
[ 27.066477] random: crng init done
[ 27.156340] PPP generic driver version 2.4.2
[ 27.183974] PPP MPPE Compression module registered
[ 27.199611] NET: Registered protocol family 24
[ 27.218213] PPTP driver version 0.8.5
[ 27.368426] ath9k 0000:00:12.0: enabling device (0000 → 0002)
[ 27.408317] ath: phy0: Ignoring endianness difference in EEPROM magic bytes.
[ 27.416965] ath: EEPROM regdomain: 0×0 [ 27.416971] ath: EEPROM indicates default country code should be used
[ 27.416974] ath: doing EEPROM country→regdmn map search
[ 27.416984] ath: country maps to regdmn code: 0x3a
[ 27.416989] ath: Country alpha2 being used: US
[ 27.416992] ath: Regpair used: 0x3a
[ 27.433820] ieee80211 phy0: Selected rate control algorithm ‘minstrel_ht’ [ 27.435348] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xb0010000, irq=19
[ 27.442114] ath9k 0000:00:11.0: enabling device (0000 → 0002)
[ 27.584297] ath: phy1: Ignoring endianness difference in EEPROM magic bytes.
[ 27.592914] ath: EEPROM regdomain: 0×0 [ 27.592920] ath: EEPROM indicates default country code should be used
[ 27.592923] ath: doing EEPROM country→regdmn map search
[ 27.592933] ath: country maps to regdmn code: 0x3a
[ 27.592938] ath: Country alpha2 being used: US
[ 27.592940] ath: Regpair used: 0x3a
[ 27.607441] ieee80211 phy1: Selected rate control algorithm ‘minstrel_ht’ [ 27.608985] ieee80211 phy1: Atheros AR9280 Rev:2 mem=0xb0000000, irq=18
[ 27.702755] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 44.364371] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts:
[ 44.414576] Adding 976560k swap on /dev/sda1. Priority:-2 extents:1 across:976560k
[ 48.643400] eth0: link up (1000Mbps/Full duplex)
[ 48.648969] br-lan: port 1(eth0) entered blocking state
[ 48.654275] br-lan: port 1(eth0) entered disabled state
[ 48.659807] device eth0 entered promiscuous mode
[ 48.692372] br-lan: port 1(eth0) entered blocking state
[ 48.697596] br-lan: port 1(eth0) entered forwarding state
[ 48.703176] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 48.790578] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 48.835679] IPv6: ADDRCONF(NETDEV_UP): eth1.2: link is not ready
[ 48.951180] IPv6: ADDRCONF(NETDEV_UP): eth1.7: link is not ready
[ 49.712398] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 51.437743] eth1: link up (1000Mbps/Full duplex)
[ 51.513573] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 51.582425] IPv6: ADDRCONF(NETDEV_CHANGE): eth1.2: link becomes ready
[ 51.589118] IPv6: ADDRCONF(NETDEV_CHANGE): eth1.7: link becomes ready
[ 54.282504] ath: EEPROM regdomain: 0×8114 [ 54.286516] ath: EEPROM indicates we should expect a country code
[ 54.292634] ath: doing EEPROM country→regdmn map search
[ 54.297928] ath: country maps to regdmn code: 0×37 [ 54.302722] ath: Country alpha2 being used: DE
[ 54.307157] ath: Regpair used: 0×37 [ 54.310630] ath: regdomain 0×8114 dynamically updated by user
[ 54.316523] ath: EEPROM regdomain: 0×8114 [ 54.320516] ath: EEPROM indicates we should expect a country code
[ 54.326609] ath: doing EEPROM country→regdmn map search
[ 54.331904] ath: country maps to regdmn code: 0×37 [ 54.336698] ath: Country alpha2 being used: DE
[ 54.341125] ath: Regpair used: 0×37 [ 54.344620] ath: regdomain 0×8114 dynamically updated by user
[ 54.836482] pppoe-wan: renamed from ppp0
[ 57.427192] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 57.492852] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 57.616731] br-lan: port 2(wlan0) entered blocking state
[ 57.622045] br-lan: port 2(wlan0) entered disabled state
[ 57.627773] device wlan0 entered promiscuous mode
[ 57.632654] br-lan: port 2(wlan0) entered blocking state
[ 57.637986] br-lan: port 2(wlan0) entered forwarding state
[ 57.693619] br-lan: port 3(wlan1) entered blocking state
[ 57.698935] br-lan: port 3(wlan1) entered disabled state
[ 57.704667] device wlan1 entered promiscuous mode
[ 58.525536] br-lan: port 2(wlan0) entered disabled state
[ 58.531209] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 58.537780] br-lan: port 3(wlan1) entered blocking state
[ 58.543145] br-lan: port 3(wlan1) entered forwarding state
[ 58.750884] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 58.757483] br-lan: port 2(wlan0) entered blocking state
[ 58.762856] br-lan: port 2(wlan0) entered forwarding state
[84181.737818] pppoe-wan: renamed from ppp0
[144550.658055] pppoe-wan: renamed from ppp0
[159913.299297] eth1: link down
[159918.352853] IPv6: ADDRCONF(NETDEV_UP): eth1.7: link is not ready
[159919.249344] eth1: link up (1000Mbps/Full duplex)
[159919.251734] IPv6: ADDRCONF(NETDEV_CHANGE): eth1.7: link becomes ready
[159923.807531] eth1: link down
[159924.830488] eth1: link up (1000Mbps/Full duplex)
[159931.219728] eth1: link down
[159936.244722] IPv6: ADDRCONF(NETDEV_UP): eth1.7: link is not ready
[159950.979373] eth1: link up (1000Mbps/Full duplex)
[159950.982129] IPv6: ADDRCONF(NETDEV_CHANGE): eth1.7: link becomes ready
[160110.252218] pppoe-wan: renamed from ppp0
[246512.671046] pppoe-wan: renamed from ppp0
[260793.131776] pppoe-wan: renamed from ppp0
[347195.313169] pppoe-wan: renamed from ppp0
[433596.980231] pppoe-wan: renamed from ppp0
[449177.428433] pppoe-wan: renamed from ppp0
[535580.336441] pppoe-wan: renamed from ppp0
root@router:~#

BusyBox v1.31.1 () built-in shell (ash)

_______                     ________        __

| |.—–.—–.—–.| | | |.—-.| |_
| - || _ | -| || | | || _|| _|
|
_|| |_||||||| ||

        |__| W I R E L E S S   F R E E D O M

—————————————————– OpenWrt SNAPSHOT, r12259-2f1cc5c3d5


root@router:~# dmesg
[ 0.000000] Linux version 4.19.101 (moeller@work-horse) (gcc version 8.3.0 (OpenWrt GCC 8.3.0 r12053-9e799f3eee)) #0 Tue Feb 18 15:10:31 2020
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
[ 0.000000] MIPS: machine is Netgear WNDR3700 v2
[ 0.000000] SoC: Atheros AR7161 rev 2
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0×0000000000000000-0x0000000003ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0×0000000000000000-0x0000000003ffffff]
[ 0.000000] Initmem setup node 0 [mem 0×0000000000000000-0x0000000003ffffff]
[ 0.000000] On node 0 totalpages: 16384
[ 0.000000] Normal zone: 144 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 16384 pages, LIFO batch:3
[ 0.000000] random: get_random_bytes called from start_kernel+0×98/0x4a8 with crng_init=0
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16240
[ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 57452K/65536K available (4336K kernel code, 180K rwdata, 1020K rodata, 1240K init, 206K bss, 8084K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 51
[ 0.000000] CPU clock: 680.000 MHz [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 5621354254 ns
[ 0.000008] sched_clock: 32 bits at 340MHz, resolution 2ns, wraps every 6316128254ns
[ 0.007802] Calibrating delay loop... 452.19 BogoMIPS (lpj=2260992)
[ 0.074072] pid_max: default: 32768 minimum: 301
[ 0.078916] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.085519] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.096900] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.106767] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.112979] pinctrl core: initialized pinctrl subsystem
[ 0.119049] NET: Registered protocol family 16
[ 0.428873] PCI host bridge /ahb/apb/pcie-controller@17010000 ranges:
[ 0.435329] MEM 0×0000000010000000..0x0000000016ffffff
[ 0.440561] IO 0×0000000000000000..0×0000000000000000 [ 0.463724] PCI host bridge to bus 0000:00
[ 0.467827] pci_bus 0000:00: root bus resource [mem 0×10000000-0x16ffffff]
[ 0.474747] pci_bus 0000:00: root bus resource [io 0×0000]
[ 0.480307] pci_bus 0000:00: root bus resource [??? 0×00000000 flags 0×0]
[ 0.487093] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.495479] pci 0000:00:11.0: [168c:ff1d] type 00 class 0×020000 [ 0.495512] pci 0000:00:11.0: reg 0×10: [mem 0×00000000-0x0000ffff]
[ 0.495815] pci 0000:00:12.0: [168c:ff1d] type 00 class 0×020000 [ 0.495841] pci 0000:00:12.0: reg 0×10: [mem 0×00000000-0x0000ffff]
[ 0.496401] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 0.496430] pci 0000:00:11.0: BAR 0: assigned [mem 0×10000000-0x1000ffff]
[ 0.503258] pci 0000:00:12.0: BAR 0: assigned [mem 0×10010000-0x1001ffff]
[ 0.513082] clocksource: Switched to clocksource MIPS
[ 0.519172] NET: Registered protocol family 2
[ 0.524330] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes)
[ 0.532014] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.539035] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.545408] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.551886] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.557771] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.564323] NET: Registered protocol family 1
[ 0.568729] PCI: CLS 0 bytes, default 32
[ 0.571378] Crashlog allocated RAM at address 0x3f00000
[ 0.577915] workingset: timestamp_bits=14 max_order=14 bucket_order=0
[ 0.590375] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.596252] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) © 2001-2006 Red Hat, Inc.
[ 0.616936] io scheduler noop registered
[ 0.620852] io scheduler deadline registered (default)
[ 0.626692] ar7100-usb-phy 18030000.usb-phy: phy reset is missing
[ 0.633681] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.640613] console [ttyS0] disabled
[ 0.644274] 18020000.uart: ttyS0 at MMIO 0×18020000 (irq = 10, base_baud = 10625000) is a 16550A
[ 0.653058] console [ttyS0] enabled
[ 0.660028] bootconsole [early0] disabled
[ 0.674536] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
[ 0.679618] 4 fixed-partitions partitions found on MTD device spi0.0
[ 0.686021] Creating 4 MTD partitions on “spi0.0”:
[ 0.690808] 0×000000000000-0×000000050000 : “u-boot” [ 0.696550] 0×000000050000-0×000000070000 : “u-boot-env” [ 0.702548] 0×000000070000-0x000000ff0000 : “firmware” [ 0.711065] 2 netgear-fw partitions found on MTD device firmware
[ 0.717127] Creating 2 MTD partitions on “firmware”:
[ 0.722090] 0×000000000000-0x0000001c5440 : “kernel” [ 0.727837] 0x0000001c5440-0x000000f80000 : “rootfs” [ 0.733518] mtd: device 4 (rootfs) set to be root filesystem
[ 0.740540] 1 squashfs-split partitions found on MTD device rootfs
[ 0.746771] 0x0000007e0000-0x000000f80000 : “rootfs_data” [ 0.752926] 0x000000ff0000-0×000001000000 : “art” [ 0.758843] Realtek RTL8366S ethernet switch driver version 0.2.2
[ 0.765052] rtl8366s rtl8366s: cannot find mdio node phandle
[ 0.770719] rtl8366s rtl8366s: using GPIO pins 5 (SDA) and 7 (SCK)
[ 0.777005] rtl8366s rtl8366s: RTL8366 ver. 1 chip found
[ 0.827344] libphy: rtl8366s: probed
[ 0.833038] libphy: Fixed MDIO Bus: probed
[ 1.184827] ag71xx 19000000.eth: connected to PHY at fixed-0:00 [uid=00000000, driver=Generic PHY]
[ 1.194429] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode: rgmii
[ 1.534679] ag71xx 1a000000.eth: connected to PHY at rtl8366s:04 [uid=001cc960, driver=Generic PHY]
[ 1.544386] eth1: Atheros AG71xx at 0xba000000, irq 5, mode: rgmii
[ 1.552885] NET: Registered protocol family 10
[ 1.562197] Segment Routing with IPv6
[ 1.566017] NET: Registered protocol family 17
[ 1.570511] 8021q: 802.1Q VLAN Support v1.8
[ 1.587431] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[ 1.598222] Freeing unused kernel memory: 1240K
[ 1.602744] This architecture does not have kernel memory protection.
[ 1.609207] Run /sbin/init as init process
[ 2.583093] random: fast init done
[ 2.802168] init: Console is alive
[ 2.805875] init: - watchdog -
[ 6.090295] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 6.231212] usbcore: registered new interface driver usbfs
[ 6.236831] usbcore: registered new interface driver hub
[ 6.242219] usbcore: registered new device driver usb
[ 6.281739] SCSI subsystem initialized
[ 6.292568] usbcore: registered new interface driver usb-storage
[ 6.299577] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 6.309264] init: - preinit -
[ 8.224350] random: jshn: uninitialized urandom read (4 bytes read)
[ 8.466243] random: jshn: uninitialized urandom read (4 bytes read)
[ 8.754611] random: jshn: uninitialized urandom read (4 bytes read)
[ 9.618495] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 9.752825] urandom_read: 4 callbacks suppressed
[ 9.752833] random: procd: uninitialized urandom read (4 bytes read)
[ 10.673421] eth0: link up (1000Mbps/Full duplex)
[ 10.678056] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 20.006729] mount_root: loading kmods from internal overlay
[ 20.070104] kmodloader: loading kernel modules from etc/modules-boot.d/*
[ 20.078087] kmodloader: done loading kernel modules from
etc/modules-boot.d/*
[ 20.858277] jffs2_scan_eraseblock(): End of filesystem marker found at 0×30000 [ 20.865541] jffs2_build_filesystem(): unlocking the mtd device...
[ 20.865544] done.
[ 20.873637] jffs2_build_filesystem(): erasing all blocks after the end marker...
[ 78.939877] done.
[ 78.949323] jffs2: notice: (558) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 78.965200] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 78.972247] block: unable to load configuration (fstab: Entry not found)
[ 78.979108] block: attempting to load /tmp/jffs_cfg/etc/config/fstab
[ 78.985665] block: unable to load configuration (fstab: Entry not found)
[ 78.992448] block: attempting to load /etc/config/fstab
[ 79.062790] block: extroot: not configured
[ 79.566994] jffs2: notice: (556) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 80.268686] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 80.275845] block: unable to load configuration (fstab: Entry not found)
[ 80.282637] block: attempting to load /tmp/jffs_cfg/etc/config/fstab
[ 80.289201] block: unable to load configuration (fstab: Entry not found)
[ 80.296055] block: attempting to load /etc/config/fstab
[ 80.301752] block: extroot: not configured
[ 80.307978] mount_root: overlay filesystem has not been fully initialized yet
[ 80.321266] mount_root: switching to jffs2 overlay
[ 80.389579] overlayfs: upper fs does not support tmpfile.
[ 83.093791] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 83.182093] eth0: link down
[ 83.196988] procd: - early -
[ 83.199968] procd: - watchdog -
[ 83.834517] procd: - watchdog -
[ 83.837950] procd: - ubus -
[ 83.904783] random: ubusd: uninitialized urandom read (4 bytes read)
[ 83.912132] random: ubusd: uninitialized urandom read (4 bytes read)
[ 83.919702] procd: - init -
[ 84.893323] kmodloader: loading kernel modules from /etc/modules.d/*
[ 85.045275] tun: Universal TUN/TAP device driver, 1.6
[ 85.069431] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 85.119219] gre: GRE over IPv4 demultiplexor driver
[ 85.139270] ip_gre: GRE over IPv4 tunneling driver
[ 85.484432] Mirror/redirect action on
[ 85.511393] u32 classifier
[ 85.514167] input device check on
[ 85.517816] Actions configured
[ 85.563375] Loading modules backported from Linux version v5.4-rc8-0-gaf42d3466bdc
[ 85.570932] Backport generated by backports.git v5.4-rc8-1-0-g368e8c51
[ 85.594056] urngd: v1.0.2 started.
[ 85.779351] usbcore: registered new interface driver usbserial_generic
[ 85.786017] usbserial: USB Serial support registered for generic
[ 85.834097] wireguard: WireGuard 0.0.20200215 loaded. See www.wireguard.com for information.
[ 85.842525] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld Jason@zx2c4.com. All Rights Reserved.
[ 86.062495] xt_time: kernel timezone is -0000
[ 86.197742] random: crng init done
[ 86.337283] PPP generic driver version 2.4.2
[ 86.361591] PPP MPPE Compression module registered
[ 86.378734] NET: Registered protocol family 24
[ 86.408191] PPTP driver version 0.8.5
[ 86.566705] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 104.504191] eth0: link up (1000Mbps/Full duplex)
[ 104.509789] br-lan: port 1(eth0) entered blocking state
[ 104.515094] br-lan: port 1(eth0) entered disabled state
[ 104.520630] device eth0 entered promiscuous mode
[ 104.604615] br-lan: port 1(eth0) entered blocking state
[ 104.609845] br-lan: port 1(eth0) entered forwarding state
[ 104.615450] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 104.663301] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 104.708562] IPv6: ADDRCONF(NETDEV_UP): eth1.2: link is not ready
[ 104.808242] IPv6: ADDRCONF(NETDEV_UP): eth1.7: link is not ready
[ 105.553190] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 106.773996] eth1: link up (1000Mbps/Full duplex)
[ 106.851719] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 106.911421] IPv6: ADDRCONF(NETDEV_CHANGE): eth1.2: link becomes ready
[ 106.918175] IPv6: ADDRCONF(NETDEV_CHANGE): eth1.7: link becomes ready
[ 108.903192] pppoe-wan: renamed from ppp0
root@router:~#

Note, the lack of anything related to the ath9K driver in the second dmesg.

Following the instructions on External Linkhttps://openwrt.org/docs/guide-user/network/wifi/basic to regenerate the wireless configuration:
rm -f /etc/config/wireless
wifi config

resulted in an empty /etc/config/wireless:
root@router:~# ls -all /etc/config/wireless
-rw-r–r– 1 root root 0 Feb 21 23:12 /etc/config/wireless
root@ router:~# cat /etc/config/wireless

Due to the rename of the platform from wndr3700v2 to wndr3700-v2 the build config had to be edited (recreated by a new run of menuconfig).

Let me know if I can do anything to help get this debugged.

25.02.20202856Base systemBug ReportVery LowHighWifi "dies" (hostapd drops all clients) on some ar71xx ...openwrt-19.07New Task Description

This issue is very strange, i don’t even know if it’s just faulty hardware but i have it happening on multiple devices now

Most affected hardware

  • Nanobridge M5 , in this case transmitting enough data can trigger it almost instantly
  • TL-WR841ND , in this case i had it happen like 3-4 times a year
  • CPE 210 v3 , in this case it happens like each week

For the last one, which is running 19.07 i found on the system log

Tue Feb 25 07:38:58 2020 daemon.notice hostapd: wlan0: AP-STA-DISCONNECTED [redacted mac1]
Tue Feb 25 07:38:58 2020 daemon.info hostapd: wlan0: STA [redacted mac1] IEEE 802.11: disassociated due to inactivity
Tue Feb 25 07:38:59 2020 daemon.info hostapd: wlan0: STA [redacted mac1] IEEE 802.11: deauthenticated due to inactivity (timer DEAUTH/REMOVE)
Tue Feb 25 07:41:32 2020 daemon.notice hostapd: wlan0: AP-STA-DISCONNECTED [redacted mac2]
Tue Feb 25 07:41:32 2020 daemon.info hostapd: wlan0: STA [redacted mac2] IEEE 802.11: disassociated due to inactivity
Tue Feb 25 07:41:33 2020 daemon.info hostapd: wlan0: STA [redacted mac2] IEEE 802.11: deauthenticated due to inactivity (timer DEAUTH/REMOVE)
Tue Feb 25 07:42:49 2020 daemon.notice hostapd: wlan0: AP-STA-POLL-OK [redacted mac3]
Tue Feb 25 07:49:55 2020 daemon.notice hostapd: wlan0: AP-STA-POLL-OK [redacted mac3]
Tue Feb 25 07:55:02 2020 daemon.notice hostapd: wlan0: AP-STA-POLL-OK [redacted mac3]
Tue Feb 25 08:00:15 2020 daemon.notice hostapd: wlan0: AP-STA-POLL-OK [redacted mac3]
Tue Feb 25 08:05:25 2020 daemon.notice hostapd: wlan0: AP-STA-POLL-OK [redacted mac3]
Tue Feb 25 08:10:44 2020 daemon.notice hostapd: wlan0: AP-STA-POLL-OK [redacted mac3]
Tue Feb 25 08:16:00 2020 daemon.notice hostapd: wlan0: AP-STA-POLL-OK [redacted mac3]
10.03.20202893Base systemBug ReportVery LowHighEthernet port not receiving data on Ubiquiti LiteAP ac ...TrunkUnconfirmed Task Description

Hi,

The Ubiquiti LiteAP ac (LAP-120) does not receive incoming packets via eth0 with the latest snapshot (OpenWrt SNAPSHOT, r12498-2a18840cc7):

root@OpenWrt:/# ifconfig 
br-lan    Link encap:Ethernet  HWaddr B4:FB:E4:FA:FA:FA
          inet addr:192.168.1.1  Bcast:192.168.1.255  Mask:255.255.255.0
          inet6 addr: fdaa:a708:e003::1/60 Scope:Global
          inet6 addr: fe80::b6fb:e4ff:fefa:fafa/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:34 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 B)  TX bytes:4420 (4.3 KiB)

eth0      Link encap:Ethernet  HWaddr B4:FB:E4:FA:FA:FA  
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:49 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 B)  TX bytes:6622 (6.4 KiB)
          Interrupt:4

It works correctly with latest stable, 19.07.2.

Using tcpdump on the connected computer I see outgoing traffic from the device, but incoming traffic does not reach the device.

The device correctly detects link changes, but different link speeds make no difference:

[ 1536.519019] eth0: link down
[ 1536.522824] br-lan: port 1(eth0) entered disabled state
[ 1537.561807] eth0: link up (1000Mbps/Full duplex)
[ 1537.566554] br-lan: port 1(eth0) entered blocking state
[ 1537.571932] br-lan: port 1(eth0) entered forwarding state
[ 1541.719009] eth0: link down
[ 1541.722824] br-lan: port 1(eth0) entered disabled state
[ 1542.761703] eth0: link up (100Mbps/Half duplex)
[ 1542.766359] br-lan: port 1(eth0) entered blocking state
[ 1542.771738] br-lan: port 1(eth0) entered forwarding state
[ 1545.879008] eth0: link down
[ 1545.882820] br-lan: port 1(eth0) entered disabled state
[ 1546.921800] eth0: link up (10Mbps/Half duplex)
[ 1546.926365] br-lan: port 1(eth0) entered blocking state
[ 1546.931744] br-lan: port 1(eth0) entered forwarding state

Please find attached dmesg outputs for both snapshot (snap) and 19.07.2 (19072).

13.03.20202901Base systemBug ReportVery LowHighFlow offload not working properly in case of IPv6 (NAT6...openwrt-19.07Unconfirmed Task Description

Linksys WRT32X with NAT6 configuration.

On latest 19.07 branch r10959

With the flow_offload feature turned on, nat6 is not working properly.
The first (or several) TCP packets seemed to be fine but later packets were not properly transmitted. The connection was soon closed.

(In case of accessing ipv6.google.com, the browser would freeze. And the curl would freeze after receiving a portion of the HTML content.)

In the meantime, ICMPv6 worked normally.

After removing the FLOWOFFLOAD ip6tables record, everything is fine.
After inserting the `-m conntrack –cstate RELATED,ESTABLISHED -j ACCEPT` before the FLOWOFFLOAD everything is also fine.

IPv4 part looked normal even if flow_offload is on.

NAT6 worked on older versions like 18.04 branch with flow_offload enabled.

17.03.20202906Base systemBug ReportVery LowHighAdding v4 Static routes without selecting 'Advanced' Ta...openwrt-19.07Unconfirmed Task Description

Using Openwrt 19.07.2 release;
On TP-Link c2600 & N750(wdr4300 v1.4)

Observed behavior:

Adding a static v4 route i.e 172.16.253.0 via 172.16.253.254 in the Luci Static route page succesfully adds the route, and by default appears to select the local route table. However viewing the routes list in status or via ip r s on cli does not show the entry.

Work-Around:

Ensure that a different table is selected in the 'Advanced tab' then go back in and add it to the correct appropriate route table.



Expected behaviour:

Adding a static route add's it to the system route table irrespective of needing to switch into advanced tab and select a non-default route table first.


21.03.20202912Base systemBug ReportVery LowHighPhicomm K3 (bcm53xx) wifi channel can't be set to auto ...openwrt-19.07Unconfirmed Task Description

Device:Phicomm K3 (bcm53xx)
BUG:wifi channel can’t set to auto mode
Description:Wifi channel can’t set to auto mode in Network - Wireless.
When wireless channel sets to auto mode, wireless settings will change from AP to Cilent even I don’t do that.

23.03.20202922Base systemBug ReportVery LowHighNo COMFAST CF-E110NV2 8MB flash compatible versionTrunkUnconfirmed Task Description

CF-E110V2 is released with 8MB Flash (maybe it was before with 16 but apparently no longer, see forum discussions on CF-E110)
The current released package is only for 16MB flash

Can You generate and publicly release a 8MB flash compatible version too.

Hereafter the modified part of the dts file I’m using to compile my own FW (based on original OEM partition table).

flash@0 {
	compatible = "winbond,w25q64", "jedec,spi-nor";
	reg = <0>;
	spi-max-frequency = <25000000>;
	partitions {
		compatible = "fixed-partitions";
		#address-cells = <1>;
		#size-cells = <1>;
		partition@0 {
			label = "u-boot";
			reg = <0x000000 0x010000>;
			read-only;
		};
		art: partition@10000 {
			label = "art";
			reg = <0x010000 0x010000>;
			read-only;
		};
		partition@20000 {
			compatible = "denx,uimage";
			label = "firmware";
			reg = <0x020000 0x7d0000>;
		};
		partition@7f0000 {
			label = "nvram";
			reg = <0x7f0000 0x010000>;
			read-only;
		};
	};
};
 


26.03.20202931Base systemBug ReportVery LowHighloading package information never arrivedopenwrt-19.07Unconfirmed Task Description

using fresh install

from Luci interface goto menu
system/software
the loading package information never arrived

pushing the update list button
the loading package information never arrived

using the console
opk update, list... are working well


07.04.20202977Base systemBug ReportVery LowHighParameters sendopts seems to be bad formated in the cal...openwrt-19.07Unconfirmed Task Description

The options parameters sendopts define in /etc/config/network seems to be badly formated in the call of the command odhcp6c

In /etc/config/network:

 

option sendopts “11:00 15:456544 16:1234”

is parsed like this (show via ps|grep odhcp6c)
-x11 00 -x15 456544 -x16 1234

The syntax given by the help of odhcp6c is different:

-x <opt>:<val> Add option opt (with value val) in sent packets (cumulative)

		Examples of IPv6 address, string and base-16 encoded options:
		-x dns:2001:2001::1,2001:2001::2 - option 23
		-x 15:office - option 15 (userclass)
		-x 0x1f4:ABBA - option 500
		-x 202:'"file"' - option 202

It appears than the : is replace by a space in the call of the command.
Regarding the help of the command, it should be :
-x 11:00 -x 15:456544 -x 16:1234

Thanks
Regards

08.04.20202980Base systemBug ReportVery LowHighNo connection to Ethernet portTrunkUnconfirmed Task Description

Hi,
I can’t connect to my board with ethernet port, my chip is mt7688 and branch is master, I tested board with 19.07 branch, it seems all is OK.
Below are the logs with serial port :

root@OpenWrt:/# [  306.094979] mtk_soc_eth 10100000.ethernet eth0: transmit timed out
[  306.101270] mtk_soc_eth 10100000.ethernet eth0: dma_cfg:00000057
[  306.107392] mtk_soc_eth 10100000.ethernet eth0: tx_ring=0, base=0707c000, max=1024, ctx=1, dtx=0, fdx=0, next=1
[  306.117655] mtk_soc_eth 10100000.ethernet eth0: rx_ring=0, base=0701c000, max=1024, calc=0, drx=1
[  316.094980] mtk_soc_eth 10100000.ethernet eth0: transmit timed out
[  316.101273] mtk_soc_eth 10100000.ethernet eth0: dma_cfg:00000057
[  316.107393] mtk_soc_eth 10100000.ethernet eth0: tx_ring=0, base=0707c000, max=1024, ctx=1, dtx=0, fdx=0, next=1
[  316.117657] mtk_soc_eth 10100000.ethernet eth0: rx_ring=0, base=07070000, max=1024, calc=1023, drx=0
[  317.502718] rt3050-esw 10110000.esw: link changed 0x00
[  326.094981] mtk_soc_eth 10100000.ethernet eth0: transmit timed out
[  326.101274] mtk_soc_eth 10100000.ethernet eth0: dma_cfg:00000057
[  326.107394] mtk_soc_eth 10100000.ethernet eth0: tx_ring=0, base=0707c000, max=1024, ctx=2, dtx=0, fdx=0, next=2
[  326.117659] mtk_soc_eth 10100000.ethernet eth0: rx_ring=0, base=0701c000, max=1024, calc=1023, drx=0
[  336.094979] mtk_soc_eth 10100000.ethernet eth0: transmit timed out
[  336.101271] mtk_soc_eth 10100000.ethernet eth0: dma_cfg:00000057
[  336.107392] mtk_soc_eth 10100000.ethernet eth0: tx_ring=0, base=0707c000, max=1024, ctx=1, dtx=0, fdx=0, next=1
[  336.117656] mtk_soc_eth 10100000.ethernet eth0: rx_ring=0, base=07070000, max=1024, calc=1023, drx=0
[  346.094979] mtk_soc_eth 10100000.ethernet eth0: transmit timed out
[  346.101272] mtk_soc_eth 10100000.ethernet eth0: dma_cfg:00000057
[  346.107392] mtk_soc_eth 10100000.ethernet eth0: tx_ring=0, base=0707c000, max=1024, ctx=1, dtx=0, fdx=0, next=1
[  346.117654] mtk_soc_eth 10100000.ethernet eth0: rx_ring=0, base=0701c000, max=1024, calc=1023, drx=0
[  356.094981] mtk_soc_eth 10100000.ethernet eth0: transmit timed out
[  356.101273] mtk_soc_eth 10100000.ethernet eth0: dma_cfg:00000057
[  356.107393] mtk_soc_eth 10100000.ethernet eth0: tx_ring=0, base=0707c000, max=1024, ctx=1, dtx=0, fdx=0, next=1
[  356.117657] mtk_soc_eth 10100000.ethernet eth0: rx_ring=0, base=07070000, max=1024, calc=1023, drx=0
 


09.04.20202986Base systemBug ReportVery LowHighFunctionality broken by migration to DSA for Ubiquiti E...TrunkUnconfirmed Task Description

Supply the following if possible:
- Ubiquiti ER-X
- Trunk
- Build trunk of Openwrt and try to configure vlan enabled interfaces on an embedded switch.

Hi.

I have Ubiquiti ER-X which I have been using for quite a while and it was working just fine.
I was using it to route traffic from external internet connections to a ‘trunk’ port connected to a different OpenWrt device used as access point. So to clarify: I have one of the swich ports configured as ‘tagged’ (’tunk’) for multiple vlans.

Unfortunately commit 30644bc579e771e4b6dcc165ca966124e0259e1e that switched this device to use DSA for switch configuration have completely broken this setup.

And I’m not talking abut soft bricking - that was to be expected. Unfortunately DSA doesn’t provide functionality that was available in swconfig for years. Namely it seems to be impossible to configure switch ports to be ‘tagged’.

It looks like DSA is considered to be ‘the future’ but unfortunately it doesn’t see to be ready for prime time - it seems to be impossible to use DSA enabled devices in configurations that were perfectly possible before.

13.04.20203005Base systemBug ReportVery LowHighiptables ruleset order improvement optionTrunkUnconfirmed Task Description

Supply the following if possible:
- Device problem occurs on
TP-Link Archer C7 v5
- Software versions of OpenWrt/LEDE release, packages, etc.
19.07.2, just default packages
- Steps to reproduce
Current iptable ordering is badly pessimal (this repeats 3x, so 3 states get set for each connection, but thats for other news)
```
-A FORWARD -m comment –comment “!fw3: Custom forwarding rule chain” -j forwarding_rule
-A FORWARD -m conntrack –ctstate RELATED,ESTABLISHED -m comment –comment “!fw3” -j ACCEPT
-A FORWARD -m conntrack –ctstate INVALID -m comment –comment “!fw3” -j DROP
```
following does same job but does significantly less processing for typical case of in-state packets
```
-A FORWARD -m conntrack –ctstate RELATED,ESTABLISHED -m comment –comment “!fw3” -j ACCEPT
-A FORWARD -m conntrack –ctstate INVALID -m comment –comment “!fw3” -j DROP
-A FORWARD -m comment –comment “!fw3: Custom forwarding rule chain” -j forwarding_rule
```
Not willing to generalize, but my wifi and wire behind could not reach subscription 100Mbps in any way before the change, after change it is steady 100Mbps both ways.

21.04.20203031Base systemBug ReportVery LowHighBusybox force reinstalled when there are no opkg listsopenwrt-19.07Unconfirmed Task Description

Device problem occurs on: Turris Omnia, mvebu
Software version: OpenWrt 19.07.

Steps to reproduce:

I noticed this bug, when I forget to do before force-reinstalling busybox

opkg update

If there isn’t anything in folder /var/opkg-lists

root@turris:/# ls -la /var/opkg-lists
ls: /var/opkg-lists: No such file or directory

It is possible to remove busybox, which should not happen.

root@turris:/# opkg install busybox --force-reinstall
Removing package busybox from root...
Installing busybox (1.30.1-5.18) to root...
Collected errors:
 * opkg_download_pkg: Package busybox is not available from any configured src.
 * opkg_install_pkg: Failed to download busybox. Perhaps you need to run 'opkg update'?
 * opkg_install_cmd: Cannot install package busybox.

And then the device ends up being in a non-specific state when you can not do anything and you need to flash firmware it once again.

If you do

opkg update

before force-reinstalling busybox, it refuses to do it which is correct.

root@turris:~# opkg install busybox --force-reinstall
Refusing to remove essential package busybox.
        Removing an essential package may lead to an unusable system, but if
        you enjoy that kind of pain, you can force opkg to proceed against
        its will with the option: --force-removal-of-essential-packages
No packages removed.
Package busybox (1.30.1-5.18) installed in root is up to date.
08.05.20203072Base systemBug ReportVery LowHighSamknows WhiteBox8 misses 2.4 GHz pcie wireless NICTrunkUnconfirmed Task Description

device

software versions

tested & misses 2.4 GHz NIC

tested & has 2.4 GHz NIC

reproduce

  • build OpenWrt master branch with a given commits and flash it on the device (my build config is attached)
  • run “iw dev” or “iw list”
    • in problem state it lists one interface (the 5 GHz wireless NIC)
    • in good state it lists two interfaces (2.4 GHz and 5 GHz wireless NIC)

conclusion

I think it has either to do with ramips: mt7621: switch kernel version to 5.4 or with ramips: mt7621: update PCIe node in dtsi. Between the known good and earliest known bad commit are multiple commits working together. I fear to test them one by one.

09.05.20203079Base systemBug ReportVery LowHighTraceback when booting OpenWrt 19.07.2 on Netgear r7500...TrunkUnconfirmed Task Description

My Netgear r7500v2 running OpenWrt 19.07.2 always shows the following traceback when booting up.

[ 31.917130] ————[ cut here ]———— [ 31.917192] WARNING: CPU: 1 PID: 1938 at backports-4.19.98-1/net/wireless/util.c:1147 0xbf2e3d88 [cfg80211@bf2df000+0×37000]
[ 31.920831] invalid rate bw=0, mcs=15, nss=4
[ 31.932143] Modules linked in: pppoe ppp_async ath10k_pci ath10k_core ath pppox ppp_generic nf_conntrack_ipv6 mac80211 iptable_nat ipt_REJECT ipt_MASQUERADE cfg80211 xt_time xt_tcpudp xt_state xt_nat xt_multiport xt_mark xt_mac xt_limit xt_conntrack xt_comment xt_TCPMSS xt_REDIRECT xt_LOG xt_FLOWOFFLOAD xt_CT wireguard slhc nf_reject_ipv4 nf_nat_redirect nf_nat_masquerade_ipv4 nf_conntrack_ipv4 nf_nat_ipv4 nf_nat nf_log_ipv4 nf_flow_table_hw nf_flow_table nf_defrag_ipv6 nf_defrag_ipv4 nf_conntrack_rtcache nf_conntrack iptable_mangle iptable_filter ip_tables crc_ccitt compat ledtrig_usbport nf_log_ipv6 nf_log_common ip6table_mangle ip6table_filter ip6_tables ip6t_REJECT x_tables nf_reject_ipv6 ip6_udp_tunnel udp_tunnel uas usb_storage f2fs ext4 mbcache jbd2 crc32c_generic crc32_generic leds_gpio xhci_plat_hcd
[ 31.985373] xhci_pci xhci_hcd dwc3 dwc3_of_simple ohci_platform ohci_hcd phy_qcom_dwc3 ahci ehci_platform sd_mod ahci_platform libahci_platform libahci libata scsi_mod ehci_hcd gpio_button_hotplug
[ 32.007657] CPU: 1 PID: 1938 Comm: hostapd Not tainted 4.14.171 #0
[ 32.025242] Hardware name: Generic DT based system
[ 32.031323] Function entered at [<c030f1c4>] from [<c030b390>]
[ 32.036095] Function entered at [<c030b390>] from [<c07c0664>]
[ 32.041911] Function entered at [<c07c0664>] from [<c031fa98>]
[ 32.047727] Function entered at [<c031fa98>] from [<c031faf8>]
[ 32.053544] Function entered at [<c031faf8>] from [<bf2e3d88>]
[ 32.059386] Function entered at [<bf2e3d88>] from [<bf2f17dc>]
[ 32.065179] Function entered at [<bf2f17dc>] from [<bf2fe5f4>]
[ 32.070992] Function entered at [<bf2fe5f4>] from [<bf2ff1e8>]
[ 32.076806] Function entered at [<bf2ff1e8>] from [<bf332ad0>]
[ 32.082632] Function entered at [<bf332ad0>] from [<bf332b60>]
[ 32.088438] Function entered at [<bf332b60>] from [<bf332bf8>]
[ 32.094255] Function entered at [<bf332bf8>] from [<bf2ed678>]
[ 32.100071] Function entered at [<bf2ed678>] from [<c06e190c>]
[ 32.105887] Function entered at [<c06e190c>] from [<c06e0128>]
[ 32.111702] Function entered at [<c06e0128>] from [<c06e0900>]
[ 32.117517] Function entered at [<c06e0900>] from [<c06df938>]
[ 32.123334] Function entered at [<c06df938>] from [<c06dfd54>]
[ 32.129150] Function entered at [<c06dfd54>] from [<c0689c18>]
[ 32.134967] Function entered at [<c0689c18>] from [<c068a480>]
[ 32.140782] Function entered at [<c068a480>] from [<c0307b60>]
[ 32.146678] —[ end trace 97f7e93c858c392e ]—

11.05.20203092Base systemBug ReportVery LowHighXiaomi Router 3G random rebootsopenwrt-19.07Unconfirmed Task Description

Supply the following if possible:
- Device problem occurs on
- Software versions of OpenWrt/LEDE release, packages, etc.
- Steps to reproduce

 

Hello,

I have a Xiaomi 3G router. Since the day I bought it I installed Openwrt and to tell you the truth, with version 18.06 I didn’t have any problem.

A few weeks ago I updated to the new version (19.07) using LuCI and it restarts me randomly.

I tried restoring the router, reinstalling the update and it keeps randomly rebooting. Right now I have it without any additional packages installed and it still keeps rebooting randomly.

I have noticed, that almost every time I see a reboot and look at the log file the first thing that appears is this, that is, the first line after the reboot is:

Mon May 11 22:16:59 2020 daemon.info dnsmasq[1148]: exiting on receipt of SIGTERM
Mon May 11 22:16:59 2020 daemon.info dnsmasq[2722]: started, version 2.80 cachesize 150
Mon May 11 22:16:59 2020 daemon.info dnsmasq[2722]: DNS service limited to local subnets
Mon May 11 22:16:59 2020 daemon.info dnsmasq[2722]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth no-DNSSEC no-ID loop-detect inotify dumpfile
Mon May 11 22:16:59 2020 daemon.info dnsmasq-dhcp[2722]: DHCP, IP range 192.168.2.100 -- 192.168.2.249, lease time 12h
Mon May 11 22:16:59 2020 daemon.info dnsmasq[2722]: using local addresses only for domain test
Mon May 11 22:16:59 2020 daemon.info dnsmasq[2722]: using local addresses only for domain onion
Mon May 11 22:16:59 2020 daemon.info dnsmasq[2722]: using local addresses only for domain localhost
Mon May 11 22:16:59 2020 daemon.info dnsmasq[2722]: using local addresses only for domain local
Mon May 11 22:16:59 2020 daemon.info dnsmasq[2722]: using local addresses only for domain invalid
Mon May 11 22:16:59 2020 daemon.info dnsmasq[2722]: using local addresses only for domain bind
Mon May 11 22:16:59 2020 daemon.info dnsmasq[2722]: using local addresses only for domain lan
Mon May 11 22:16:59 2020 daemon.info dnsmasq[2722]: reading /tmp/resolv.conf.auto
Mon May 11 22:16:59 2020 daemon.info dnsmasq[2722]: using local addresses only for domain test
Mon May 11 22:16:59 2020 daemon.info dnsmasq[2722]: using local addresses only for domain onion
Mon May 11 22:16:59 2020 daemon.info dnsmasq[2722]: using local addresses only for domain localhost
Mon May 11 22:16:59 2020 daemon.info dnsmasq[2722]: using local addresses only for domain local
Mon May 11 22:16:59 2020 daemon.info dnsmasq[2722]: using local addresses only for domain invalid
Mon May 11 22:16:59 2020 daemon.info dnsmasq[2722]: using local addresses only for domain bind
Mon May 11 22:16:59 2020 daemon.info dnsmasq[2722]: using local addresses only for domain lan

Please, I need help since I can’t work if it constantly resets. If you need any more information, please do not hesitate to ask me.

29.05.20203134Base systemBuild FailureVery LowHighCan't build netifdopenwrt-19.07Unconfirmed Task Description

Environment: x86_64
Arch Linux
Description: Can’t build current openwrt-19.07. (Arch Linux, tried both GCC 10.1.0 and 8.4.0. Getting two build errors:

CFLAGS="-Os -pipe -mno-branch-likely -mips32r2 -mtune=74kc -fno-caller-saves -fno-plt -fhonour-copts -Wno-error=unused-but-set-variable -Wno-error=unused-result -msoft-float -mips16 -minterlin
k-mips16 -iremap/home/legogris/dev/openwrt-fresh/build_dir/target-mipsel_74kc_musl/netifd-2019-08-05-5e02f944:netifd-2019-08-05-5e02f944 -Wformat -Werror=format-security -fstack-protector -D_F
ORTIFY_SOURCE=1 -Wl,-z,now -Wl,-z,relro -I/home/legogris/dev/openwrt-fresh/staging_dir/target-mipsel_74kc_musl/usr/include/libnl-tiny -I/home/legogris/dev/openwrt-fresh/staging_dir/target-mips
el_74kc_musl/usr/include -flto  -I/home/legogris/dev/openwrt-fresh/staging_dir/target-mipsel_74kc_musl/usr/include -I/home/legogris/dev/openwrt-fresh/staging_dir/target-mipsel_74kc_musl/includ
e -I/home/legogris/dev/openwrt-fresh/staging_dir/toolchain-mipsel_74kc_gcc-7.5.0_musl/usr/include -I/home/legogris/dev/openwrt-fresh/staging_dir/toolchain-mipsel_74kc_gcc-7.5.0_musl/include/fo
rtify -I/home/legogris/dev/openwrt-fresh/staging_dir/toolchain-mipsel_74kc_gcc-7.5.0_musl/include " CXXFLAGS="-Os -pipe -mno-branch-likely -mips32r2 -mtune=74kc -fno-caller-saves -fno-plt -fho
nour-copts -Wno-error=unused-but-set-variable -Wno-error=unused-result -msoft-float -mips16 -minterlink-mips16 -iremap/home/legogris/dev/openwrt-fresh/build_dir/target-mipsel_74kc_musl/netifd-
2019-08-05-5e02f944:netifd-2019-08-05-5e02f944 -Wformat -Werror=format-security -fstack-protector -D_FORTIFY_SOURCE=1 -Wl,-z,now -Wl,-z,relro -I/home/legogris/dev/openwrt-fresh/staging_dir/tar
get-mipsel_74kc_musl/usr/include/libnl-tiny -I/home/legogris/dev/openwrt-fresh/staging_dir/target-mipsel_74kc_musl/usr/include -flto  -I/home/legogris/dev/openwrt-fresh/staging_dir/target-mips
el_74kc_musl/usr/include -I/home/legogris/dev/openwrt-fresh/staging_dir/target-mipsel_74kc_musl/include -I/home/legogris/dev/openwrt-fresh/staging_dir/toolchain-mipsel_74kc_gcc-7.5.0_musl/usr/
include -I/home/legogris/dev/openwrt-fresh/staging_dir/toolchain-mipsel_74kc_gcc-7.5.0_musl/include/fortify -I/home/legogris/dev/openwrt-fresh/staging_dir/toolchain-mipsel_74kc_gcc-7.5.0_musl/
include " LDFLAGS="-L/home/legogris/dev/openwrt-fresh/staging_dir/target-mipsel_74kc_musl/usr/lib -L/home/legogris/dev/openwrt-fresh/staging_dir/target-mipsel_74kc_musl/lib -L/home/legogris/de
v/openwrt-fresh/staging_dir/toolchain-mipsel_74kc_gcc-7.5.0_musl/usr/lib -L/home/legogris/dev/openwrt-fresh/staging_dir/toolchain-mipsel_74kc_gcc-7.5.0_musl/lib -znow -zrelro -flto -fuse-linke
r-plugin " make  -C /home/legogris/dev/openwrt-fresh/build_dir/target-mipsel_74kc_musl/netifd-2019-08-05-5e02f944/. AR="mipsel-openwrt-linux-musl-gcc-ar" AS="mipsel-openwrt-linux-musl-gcc -c -
Os -pipe -mno-branch-likely -mips32r2 -mtune=74kc -fno-caller-saves -fno-plt -fhonour-copts -Wno-error=unused-but-set-variable -Wno-error=unused-result -msoft-float -iremap/home/legogris/dev/o
penwrt-fresh/build_dir/target-mipsel_74kc_musl/netifd-2019-08-05-5e02f944:netifd-2019-08-05-5e02f944 -Wformat -Werror=format-security -fstack-protector -D_FORTIFY_SOURCE=1 -Wl,-z,now -Wl,-z,re
lro -I/home/legogris/dev/openwrt-fresh/staging_dir/target-mipsel_74kc_musl/usr/include/libnl-tiny -I/home/legogris/dev/openwrt-fresh/staging_dir/target-mipsel_74kc_musl/usr/include -flto" LD=m
ipsel-openwrt-linux-musl-ld NM="mipsel-openwrt-linux-musl-gcc-nm" CC="mipsel-openwrt-linux-musl-gcc" GCC="mipsel-openwrt-linux-musl-gcc" CXX="mipsel-openwrt-linux-musl-g++" RANLIB="mipsel-open
wrt-linux-musl-gcc-ranlib" STRIP=mipsel-openwrt-linux-musl-strip OBJCOPY=mipsel-openwrt-linux-musl-objcopy OBJDUMP=mipsel-openwrt-linux-musl-objdump SIZE=mipsel-openwrt-linux-musl-size CROSS="
mipsel-openwrt-linux-musl-" ARCH="mipsel" CMAKE_COMMAND='/home/legogris/dev/openwrt-fresh/staging_dir/host/bin/cmake' CMAKE_DISABLE_cmake_check_build_system=1 ;
make[4]: Entering directory '/home/legogris/dev/openwrt-fresh/build_dir/target-mipsel_74kc_musl/netifd-2019-08-05-5e02f944'
make[5]: Entering directory '/home/legogris/dev/openwrt-fresh/build_dir/target-mipsel_74kc_musl/netifd-2019-08-05-5e02f944'
make[6]: Entering directory '/home/legogris/dev/openwrt-fresh/build_dir/target-mipsel_74kc_musl/netifd-2019-08-05-5e02f944'
make[6]: Leaving directory '/home/legogris/dev/openwrt-fresh/build_dir/target-mipsel_74kc_musl/netifd-2019-08-05-5e02f944'
make[6]: Entering directory '/home/legogris/dev/openwrt-fresh/build_dir/target-mipsel_74kc_musl/netifd-2019-08-05-5e02f944'
[  4%] Building C object CMakeFiles/netifd.dir/main.c.o
In file included from /home/legogris/dev/openwrt-fresh/build_dir/target-mipsel_74kc_musl/netifd-2019-08-05-5e02f944/netifd.h:29:0,
                 from /home/legogris/dev/openwrt-fresh/build_dir/target-mipsel_74kc_musl/netifd-2019-08-05-5e02f944/main.c:22:
/home/legogris/dev/openwrt-fresh/build_dir/target-mipsel_74kc_musl/netifd-2019-08-05-5e02f944/utils.h:116:51: error: 'struct uci_blob_param_list' declared inside parameter list will not be vis
ible outside of this definition or declaration [-Werror]
 const char * uci_get_validate_string(const struct uci_blob_param_list *p, int i);
                                                   ^~~~~~~~~~~~~~~~~~~
cc1: error: unrecognized command line option '-Wno-unknown-warning-option' [-Werror]
cc1: all warnings being treated as errors
make[6]: *** [CMakeFiles/netifd.dir/build.make:63: CMakeFiles/netifd.dir/main.c.o] Error 1
make[6]: Leaving directory '/home/legogris/dev/openwrt-fresh/build_dir/target-mipsel_74kc_musl/netifd-2019-08-05-5e02f944'
make[5]: *** [CMakeFiles/Makefile2:76: CMakeFiles/netifd.dir/all] Error 2
make[5]: Leaving directory '/home/legogris/dev/openwrt-fresh/build_dir/target-mipsel_74kc_musl/netifd-2019-08-05-5e02f944'
make[4]: *** [Makefile:130: all] Error 2
make[4]: Leaving directory '/home/legogris/dev/openwrt-fresh/build_dir/target-mipsel_74kc_musl/netifd-2019-08-05-5e02f944'
make[3]: *** [Makefile:49: /home/legogris/dev/openwrt-fresh/build_dir/target-mipsel_74kc_musl/netifd-2019-08-05-5e02f944/.built] Error 2
make[3]: Leaving directory '/home/legogris/dev/openwrt-fresh/package/network/config/netifd'
time: package/network/config/netifd/compile#0.33#0.08#0.39
make[2]: *** [package/Makefile:113: package/network/config/netifd/compile] Error 2
make[2]: Leaving directory '/home/legogris/dev/openwrt-fresh'
make[1]: *** [package/Makefile:107: /home/legogris/dev/openwrt-fresh/staging_dir/target-mipsel_74kc_musl/stamp/.package_compile] Error 2
make[1]: Leaving directory '/home/legogris/dev/openwrt-fresh'
make: *** [/home/legogris/dev/openwrt-fresh/include/toplevel.mk:227: world] Error 2
make -j1 V=s  20,02s user 4,25s system 102% cpu 23,565 total
03.06.20203147Base systemBug ReportVery LowHigh802.11w settings on LUCI WIFI page doesn't work properl...openwrt-19.07Unconfirmed Task Description

Host device

Device problem occurs on: Phicomm PSG1218A (MTK7620, 64M, 8MB, 802.11AC+N)
Software versions of OpenWrt/LEDE release: OpenWRT 19.07.3 Stable (r11063-85e04e9f46 / LuCI openwrt-19.07 branch git-20.136.49537-fb2f363)
Package: wpad-openssl OR hostapd-openssl

External server/service

RADIUS server: Windows Server 2019 NPAS, worked fine with WPA2-EAP

Client

Client WIFI chip and driver: Intel Dual Band Wireless-AC 8265 running newest driver version 20.70.16.4 (driver date: 01/01/2020)

Steps to reproduce:

1. initialize default settings, then remove wpad-basic and install wpad-openssl OR hostapd-openssl to enable WPA3 AP mode
2. leave 802.11w to default setting which is “Required” 3. set country setting, ssid, and etc. as required such as radius for EAP
4 if use WPA2-PSK or WPA2-EAP with default settings, everything works fine.

5. switch WIFI (AC/N) to WPA2-PSK/WPA3-SAE mixed mode (sae+ccmp or something like that) OR WPA2-EAP/WPA3-EAP mixed mode (wpa3-mixed+ccmp or something like that)
6. apply settings wait until effective or reboot to take effect

6.1 __ssid won't come up on 802.11g/n interface__ if in PSK/SAE mixed mode.

7. Client (Intel 8265) won’t be able to connect to SSID,

7.1 if ssid would come up (802.11a/ac), it would be seen on client scan, but the client (Intel 8265) won't be able to connect to SSID, reports "Can't connect", in EAP mode, router side log "Deauthenticated due to local request" after "EAP-SUCCESS"

8. switch 802.11w to other settings, including “Optional”, problem remains, router config file /etc/config/wireless would list “option ieee80211w ‘1’” 9. switch 802.11w to other settings, including “Optional”, problem still remains, router config file /etc/config/wireless will be missing the “option ieee80211w” completely, and it seems wpad or hostapd would assume “optional” (code ‘1’) as default value instead of the documented “disabled” (code ‘0’).

Steps to workaround:

Manually set “option ieee80211w ‘0’” in /etc/config/wireless to disable 802.11w and don’t update settings through LUCI on the problematic ssid, restart wifi. Everything would work.

12.06.20203176Base systemBug ReportVery LowHighpi zero AP+STA mode does not workAllUnconfirmed Task Description

Supply the following if possible:
- device: Raspberry Pi Zero W
- Versions confirmed on: recent Snapshot, 19.07.3, 18.06.8, 17.01.4
- Steps to reproduce:

  1. flash image to sd card, put sd card into pi
  2. turn on wifi radio (uci set wireless.radio0.disabled=0)
  3. add a wireless network such that one is a station and one is a AP (I’ve tried though gui and command line)
  4. restart wifi (either through reboot or wifi command)
  5. Now in the dmesg you can see wlan0-1 cycling between blocking forwarding and disabled states

Additional info:
I made this forum post about it, but not much has come from that and I’ve learned a lot since posting.

I know that this mode is supported from the iw list output -

 valid interface combinations:
                 * #{ managed } <= 1, #{ P2P-device } <= 1, #{ P2P-client, P2P-GO } <= 1,
                   total <= 3, #channels <= 2
                 * #{ managed } <= 1, #{ AP } <= 1, #{ P2P-client } <= 1, #{ P2P-device } <= 1,
                   total <= 4, #channels <= 1
        Supported extended features:
                * [ 4WAY_HANDSHAKE_STA_PSK ]: 4-way handshake with PSK in station mode
                * [ 4WAY_HANDSHAKE_STA_1X ]: 4-way handshake with 802.1X in station mode

I’ve even gotten AP+STA mode to work by manually starting a second instance of hostapd (note that im not killing the original one), but that makes it even more confusing that it doesn’t work normally.

I make sure that they are on the same channel.

If you need anything cleared up please let me know. I’ve tried for over a week now to fix this myself to no avail.

14.06.20203181Base systemBug ReportVery LowHighunable to build 19.07.3 for clearfog proopenwrt-19.07Unconfirmed Task Description

Supply the following if possible:
- Device problem occurs on
Clearfog pro

- Software versions of OpenWrt/LEDE release, packages, etc.
tag 19.07.3
- Steps to reproduce
make fails:

export CROSS="arm-openwrt-linux-muslgnueabi-"  NO_RENAME=1 ; NM="arm-openwrt-linux-muslgnueabi-nm" STRIP="/home/oli/openwrt/staging_dir/host/bin/sstrip" STRIP_KMOD="/home/oli/openwrt/scripts/strip-kmod.sh" PATCHELF="/home/oli/openwrt/staging_dir/host/bin/patchelf" /home/oli/openwrt/scripts/rstrip.sh /home/oli/openwrt/build_dir/target-arm_cortex-a9+vfpv3-d16_musl_eabi/u-boot-2018.03/ipkg-arm_cortex-a9_vfpv3-d16/uboot-envtools
rstrip.sh: /home/oli/openwrt/build_dir/target-arm_cortex-a9+vfpv3-d16_musl_eabi/u-boot-2018.03/ipkg-arm_cortex-a9_vfpv3-d16/uboot-envtools/usr/sbin/fw_printenv: executable
(cd /home/oli/openwrt/build_dir/target-arm_cortex-a9+vfpv3-d16_musl_eabi/u-boot-2018.03/ipkg-arm_cortex-a9_vfpv3-d16/uboot-envtools/CONTROL; ( echo "$CONTROL"; printf "Description: "; echo "$DESCRIPTION" | sed -e 's,^[[:space:]]*, ,g'; ) > control; chmod 644 control; ( echo "#!/bin/sh"; echo "[ \"\${IPKG_NO_SCRIPT}\" = \"1\" ] && exit 0"; echo "[ -x "\${IPKG_INSTROOT}/lib/functions.sh" ] || exit 0"; echo ". \${IPKG_INSTROOT}/lib/functions.sh"; echo "default_postinst \$0 \$@"; ) > postinst; ( echo "#!/bin/sh"; echo "[ -x "\${IPKG_INSTROOT}/lib/functions.sh" ] || exit 0"; echo ". \${IPKG_INSTROOT}/lib/functions.sh"; echo "default_prerm \$0 \$@"; ) > prerm; chmod 0755 postinst prerm; echo "$V_Package_uboot_envtools_conffiles" > conffiles;  )
install -d -m0755 /home/oli/openwrt/bin/targets/mvebu/cortexa9/packages
/home/oli/openwrt/scripts/ipkg-build -c -o 0 -g 0 /home/oli/openwrt/build_dir/target-arm_cortex-a9+vfpv3-d16_musl_eabi/u-boot-2018.03/ipkg-arm_cortex-a9_vfpv3-d16/uboot-envtools /home/oli/openwrt/bin/targets/mvebu/cortexa9/packages
/home/oli/openwrt/staging_dir/host/bin/find: '/home/oli/openwrt/build_dir/target-arm_cortex-a9+vfpv3-d16_musl_eabi/u-boot-2018.03/ipkg-arm_cortex-a9_vfpv3-d16/uboot-envtools/etc/config/ubootenv': No such file or directory
/home/oli/openwrt/staging_dir/host/bin/find: '/home/oli/openwrt/build_dir/target-arm_cortex-a9+vfpv3-d16_musl_eabi/u-boot-2018.03/ipkg-arm_cortex-a9_vfpv3-d16/uboot-envtools/etc/fw_env.config': No such file or directory
Packaged contents of /home/oli/openwrt/build_dir/target-arm_cortex-a9+vfpv3-d16_musl_eabi/u-boot-2018.03/ipkg-arm_cortex-a9_vfpv3-d16/uboot-envtools into /home/oli/openwrt/bin/targets/mvebu/cortexa9/packages/uboot-envtools_2018.03-3_arm_cortex-a9_vfpv3-d16.ipk
echo "uboot-envtools" >> /home/oli/openwrt/staging_dir/target-arm_cortex-a9+vfpv3-d16_musl_eabi/pkginfo/uboot-envtools.default.install
make[3]: Leaving directory '/home/oli/openwrt/package/boot/uboot-envtools'
time: package/boot/uboot-envtools/compile#1.27#0.68#1.71
make[3]: Entering directory '/home/oli/openwrt/package/boot/uboot-mvebu'
rm -f /home/oli/openwrt/build_dir/target-arm_cortex-a9+vfpv3-d16_musl_eabi/u-boot-clearfog/u-boot-2018.03/.built
touch /home/oli/openwrt/build_dir/target-arm_cortex-a9+vfpv3-d16_musl_eabi/u-boot-clearfog/u-boot-2018.03/.built_check
make  -C /home/oli/openwrt/build_dir/target-arm_cortex-a9+vfpv3-d16_musl_eabi/u-boot-clearfog/u-boot-2018.03 CROSS_COMPILE=arm-openwrt-linux-muslgnueabi- DTC="/home/oli/openwrt/build_dir/target-arm_cortex-a9+vfpv3-d16_musl_eabi/linux-mvebu_cortexa9/linux-4.14.180/scripts/dtc/dtc" HOSTCC="gcc" HOSTCFLAGS="-O2 -I/home/oli/openwrt/staging_dir/host/include -I/home/oli/openwrt/staging_dir/hostpkg/include -I/home/oli/openwrt/staging_dir/target-arm_cortex-a9+vfpv3-d16_musl_eabi/host/include -I/home/oli/openwrt/staging_dir/host/include -I/home/oli/openwrt/staging_dir/hostpkg/include -I/home/oli/openwrt/staging_dir/target-arm_cortex-a9+vfpv3-d16_musl_eabi/host/include -std=gnu11" HOSTLDFLAGS="-L/home/oli/openwrt/staging_dir/host/lib -L/home/oli/openwrt/staging_dir/hostpkg/lib -L/home/oli/openwrt/staging_dir/target-arm_cortex-a9+vfpv3-d16_musl_eabi/host/lib"
make[4]: Entering directory '/home/oli/openwrt/build_dir/target-arm_cortex-a9+vfpv3-d16_musl_eabi/u-boot-clearfog/u-boot-2018.03'
  CHK     include/config/uboot.release
  CHK     include/generated/version_autogenerated.h
  CHK     include/generated/timestamp_autogenerated.h
  CC      lib/asm-offsets.s
  CHK     include/generated/generic-asm-offsets.h
  UPD     include/generated/generic-asm-offsets.h
  CC      arch/arm/lib/asm-offsets.s
  CHK     include/generated/asm-offsets.h
  UPD     include/generated/asm-offsets.h
  HOSTLD  scripts/dtc/dtc
/usr/bin/ld: scripts/dtc/dtc-parser.tab.o:(.bss+0x10): multiple definition of `yylloc'; scripts/dtc/dtc-lexer.lex.o:(.bss+0x0): first defined here
collect2: error: ld returned 1 exit status
make[6]: *** [scripts/Makefile.host:108: scripts/dtc/dtc] Error 1
make[5]: *** [scripts/Makefile.build:425: scripts/dtc] Error 2
make[4]: *** [Makefile:491: scripts] Error 2
make[4]: Leaving directory '/home/oli/openwrt/build_dir/target-arm_cortex-a9+vfpv3-d16_musl_eabi/u-boot-clearfog/u-boot-2018.03'
make[3]: *** [Makefile:53: /home/oli/openwrt/build_dir/target-arm_cortex-a9+vfpv3-d16_musl_eabi/u-boot-clearfog/u-boot-2018.03/.built] Error 2
make[3]: Leaving directory '/home/oli/openwrt/package/boot/uboot-mvebu'
time: package/boot/uboot-mvebu/clearfog/compile#0.32#0.20#0.51
make[2]: *** [package/Makefile:113: package/boot/uboot-mvebu/compile] Error 2
make[2]: Leaving directory '/home/oli/openwrt'
make[1]: *** [package/Makefile:107: /home/oli/openwrt/staging_dir/target-arm_cortex-a9+vfpv3-d16_musl_eabi/stamp/.package_compile] Error 2
make[1]: Leaving directory '/home/oli/openwrt'
make: *** [/home/oli/openwrt/include/toplevel.mk:227: world] Fehler 2
20.06.20203195Base systemBug ReportVery LowHighramips/mt7621/zbt3526 -> boot failure with kernel 5.4TrunkUnconfirmed Task Description

Supply the following if possible:
- Device problem occurs on: ZBT 3526-16MB + 32 MB - Software versions of OpenWrt/LEDE: current trunk (kernel 5.4)
- Steps to reproduce: when i update the firmware, i see that there is a network after reboot for ~10sec, and then it is gone, and is not accessable, seeems to be, that something is crashing.
i can only hard-reset - nothing else.

any idea ?
maybe it is related also like the other bugs reported ? for bootloop or hanging/crashing mt7621 ?

 


27.06.20203207Base systemBug ReportVery LowHighSetting MTU on Bridged interfaces does not set MTU on m...openwrt-19.07Unconfirmed Task Description

- Device problem occurs on - x86
- Software versions of OpenWrt/LEDE release, packages, etc. - 19.07.3

 

I think it’s a bug/overlooked use case, but when you have interfaces bridged in the UCI config, the MTU setting does not get applied to the member interfaces (physical or VLAN).

config interface 'lan'
        option proto 'static'
        option netmask '255.255.255.0'
        option ip6assign '60'
        option ipaddr '192.168.1.1'
        option type 'bridge'
        option mtu '9000'
        option ifname 'eth1 eth4.10'

When I boot using this config I have connectivity issues with devices using Jumbo frames. ifconfig confirms that MTUs on the members interfaces are still at default 1500.

eth1      Link encap:Ethernet  HWaddr 0C:C4:7A:AB:39:3D
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Memory:df440000-df45ffff

eth4      Link encap:Ethernet  HWaddr 3C:FD:FE:BB:01:50
          inet6 addr: fe80::3efd:feff:febb:150/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500 Metric:1
          RX packets:50176 errors:0 dropped:1 overruns:0 frame:0
          TX packets:37468 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:15692679 (14.9 MiB)  TX bytes:29263711 (27.9 MiB)

eth4.10   Link encap:Ethernet  HWaddr 3C:FD:FE:BB:01:50
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:36728 errors:0 dropped:0 overruns:0 frame:0
          TX packets:20850 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:9314410 (8.8 MiB)  TX bytes:26473088 (25.2 MiB)

I have to manually use the ifconfig tool to set the MTU (i.e. ifconfig eth4.10 mtu 9000) to get the network back up and running correctly.

Obviously these commands could be scritped, however it was my understanding the UCI network config should be doing this .

22.07.20203242Base systemBug ReportVery LowHighUAS not working - All devices with USB3.0 affectedAllUnconfirmed Task Description

USB controller “f10f8000.usb3” is preventing UAS from working on OpenWRT devices, as dmesg states:

[ 1.830001] usb 3-1: new SuperSpeed USB device number 2 using xhci-hcd
[ 1.860632] usb 3-1: USB controller f10f8000.usb3 does not support streams, which are required by the UAS driver.
[ 1.870949] usb 3-1: Please try an other USB controller if you wish to use UAS.
[ 1.878291] usb-storage 3-1:1.0: USB Mass Storage device detected

Checked in OpenWRT 18.04 and 19.03 with Linksys WRT3200ACM and Turris Omnia. This impacts USB3.0 speeds.

To reproduce just hook up a USB3.0 HDD to a OpenWRT device on the USB3.0 port and see dmesg.

Is it possible to try another controller or fix f10f8000.usb3?

28.07.20203252Base systemBug ReportVery LowHighX86 kernel has no emmc support, cause it can't boot fro...TrunkUnconfirmed Task Description

Supply the following if possible:
- Device problem occurs on: Z83II mini pc. https://www.minipcdb.com/articles/Meet-Z83II-Mini-PC - Software versions of OpenWrt/LEDE release, packages, etc. Tested on both 19.07.3 and latest snapshots, both failed.
- Steps to reproduce: Write to image to the embedded emmc disk and boot it.

I’ve tested both 19.07.3 and latest snapshots build of openwrt x86-64 build on the Intel Z8350 fanless mini PC. Both failed to boot. The kernel can boot up correctly, but the system hang at waiting for root device. If the image is burned on USB disk, it can boot up correctly without any issue.

I searched on Google and found this post - https://forum.archive.openwrt.org/viewtopic.php?id=72195

I did the test on 19.07.3 and verified the system can boot up correctly from embedded emmc storage that by adding the following two options into the target/linux/x86/64/config-default file
CONFIG_MMC_SDHCI_ACPI
CONFIG_X86_INTEL_LPSS

Could you approve to add the options into the future update to support booting from emmc storage?
Thanks!

 


24.08.20203303Base systemBug ReportVery LowHighntfs drive not mountingTrunkUnconfirmed Task Description

Supply the following if possible:
- Device problem occurs on
- Software versions of OpenWrt/LEDE release, packages, etc.
- Steps to reproduce

 

This problem is occurring on a BT HomeHub 5A. I have two of these and the problem happens on both of them. I am currently using V5.X and the issue is only here but it is working in v19.07.3.

The issue is that I am not able to auto-mount my NTFS drive with bootup through fstab.
The error is as follows:

Sun Aug 23 21:56:03 2020 kern.notice kernel: [   11.711119] scsi 0:0:0:0: Direct-Access     Seagate  Expansion        0608 PQ: 0 ANSI: 6
Sun Aug 23 21:56:03 2020 kern.notice kernel: [   11.725022] sd 0:0:0:0: [sda] 976773167 512-byte logical blocks: (500 GB/466 GiB)
Sun Aug 23 21:56:03 2020 kern.notice kernel: [   11.733044] sd 0:0:0:0: [sda] Write Protect is off
Sun Aug 23 21:56:03 2020 kern.debug kernel: [   11.736665] sd 0:0:0:0: [sda] Mode Sense: 4f 00 00 00
Sun Aug 23 21:56:03 2020 kern.notice kernel: [   11.738710] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Sun Aug 23 21:56:03 2020 kern.warn kernel: [   11.739527] overlayfs: upper fs does not support xattr, falling back to index=off and metacopy=off.
Sun Aug 23 21:56:03 2020 kern.info kernel: [   12.012011]  sda: sda1
Sun Aug 23 21:56:03 2020 kern.notice kernel: [   12.020464] sd 0:0:0:0: [sda] Attached SCSI disk

Sun Aug 23 21:56:10 2020 daemon.err block: No "mount.ntfs" utility available
Sun Aug 23 21:56:10 2020 daemon.err block: mounting /dev/sda1 (ntfs) as /tmp/data-hdd failed (25) - Not a tty

Although I can mount the drive manually through ntfs-3g and the package is already installed but somehow the system thinks it is not available. For now the workaround is to manually mount the drive when the boot ends.

Please fix this issue thanks.

05.09.20203319Base systemBug ReportVery LowHigherratic behaviour wireless network control on system wi...TrunkUnconfirmed Task Description

Device: Ubiquiti Routerstation (ar71xx)
Software: OpenWrt SNAPSHOT, r14382+7-ad0f0df909 (local compilation after Sep 3 2020 git pull)
Symptoms: commands like ‘wifi up wlan1’ on a system with wlan0, wlan1, and wlan2 (phy0,1,2) , make other wlanN disapperar than wlan1.
plus in dmesg messages like
[ n.n] do_page_fault(): sending SIGSEGV to hostapd for invalid write access to 00000000
[ n.n] epc = 77e79e6c in libc.so[77e4c000+9c000]
[ n.s] ra = 77e1e309 in libubus.so[77e1c000+13000]

Bug found through experimentation:
script: /lib/netifd/wireless/mac80211.sh
function: drv_mac80211_teardown()
line: json_select data
problem: ‘data’ does not produce phy, ‘config’ does.
corrected line: json_select config

Going though experimentations also found that there may be problems in
script: /lib/netifd/hostapd.sh
function: wpa_supplicant_run()
line: ubus call wpa_supplicant config_add
and the lines that follow with parameters and line continuations.
Replaced:

ubus call wpa_supplicant config_add "{ \
	\"driver\": \"${_w_driver:-wext}\", \"ctrl\": \"$_rpath\", \
	\"iface\": \"$ifname\", \"config\": \"$_config\" \
	${network_bridge:+, \"bridge\": \"$network_bridge\"} \
	${hostapd_ctrl:+, \"hostapd_ctrl\": \"$hostapd_ctrl\"} \
	}"

By:

local br=${network_bridge:+',"bridge":"'$network_bridge'"'}
local hc=${hostapd_ctrl:+',"hostapd_ctrl":"'$hostapd_ctrl'"'}
local jsonstr='{"driver":"'${_w_driver:-wext}'","iface":"'${ifname}'"'${br}${hc}',"ctrl":"'${_rpath}'","config":"'${_config}'"}'
ubus call wpa_supplicant config_add ${jsonstr}

because in a separate test script just to see the workings of the original I could not get it to work due to the nested parameter substitution.
Have removed all the \” as the " do not need to be escaped when within single quotes.


14.09.20203338Base systemBug ReportVery LowHighTL-WR841N v13 (ramips) unstable Ethernet and WiFi in 19...openwrt-19.07Unconfirmed Task Description

I am using default build of OpenWRT 19.07.4 for TL-WR841N v13 without any additional packages. I have Ethernet PPPoE from provider, some ethernet and WiFi WPA2 clients. WiFi and Ethernet are unstable: they can disappear for 30-60 seconds without any serious reason. On 18.06.8 there wasn’t those problems. I attached system log. Thanks for help.

09.10.20203373Base systemBug ReportVery LowHighIPV6 flow offload brokenTrunkUnconfirmed Task Description

Enabling this option makes the ipv6 connection unstable.

Example: connecting to #openwrt-devel from hexchat (Ubuntu) makes you constantly disconnect.
Disabling flow offload makes the connection stable.


31.10.20203418Base systemBug ReportVery LowHighLatest build for TL-WR1043ND v2 (ath79) does not boot -...TrunkUnconfirmed Task Description

Device: TL-WR1043ND v2
Software versions: Linux version 5.4.72 (risa@gentoo-vb) (gcc version 9.3.0 (OpenWrt GCC 9.3.0 r14820-5cdc65f6d1)) #0 Sat Oct 31 20:27:47 2020

I am building a the latest snapshot into a custom image by using ImageBuilder, the latest build of r14820-5cdc65f6d1 does not boot, because the `/sbin/init` process misses some libraries. Following is the output from serial console during the failed boot:

U-Boot 1.1.4 (Jun 18 2013 - 15:51:52)

ap135 - Scorpion 1.0DRAM:
sri
Scorpion 1.0
ath_ddr_initial_config(178): (16bit) ddr2 init
tap = 0x00000003
Tap (low, high) = (0x0, 0x1e)
Tap values = (0xf, 0xf, 0xf, 0xf)
64 MB
Flash Manuf Id 0xef, DeviceId0 0x40, DeviceId1 0x17
flash size 8MB, sector count = 128
Flash:  8 MB
Using default environment

*** Warning *** : PCIe WLAN Module not found !!!
*** Warning *** : PCIe WLAN Module not found !!!
In:    serial
Out:   serial
Err:   serial
Net:   ath_gmac_enet_initialize...
athrs_sgmii_res_cal: cal value = 0xe
No valid address in Flash. Using fixed address
No valid address in Flash. Using fixed address
ath_gmac_enet_initialize: reset mask:c02200
Scorpion  ----> S17 PHY *
athrs17_reg_init: complete
: cfg1 0x80000000 cfg2 0x7114
eth0: ba:be:fa:ce:08:41
eth0 up
athrs17_reg_init_wan done
SGMII in forced mode
athr_gmac_sgmii_setup SGMII done
: cfg1 0x800c0000 cfg2 0x7214
eth1: ba:be:fa:ce:08:41
eth1 up
eth0, eth1
Setting 0x18116290 to 0x50a1a14f
Autobooting in 1 seconds
## Booting image at 9f020000 ...
   Uncompressing Kernel Image ... OK

Starting kernel ...

[    0.000000] Linux version 5.4.72 (risa@gentoo-vb) (gcc version 9.3.0 (OpenWrt GCC 9.3.0 r14820-5cdc65f6d1)) #0 Sat Oct 31 20:27:47 2020
[    0.000000] printk: bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019750 (MIPS 74Kc)
[    0.000000] MIPS: machine is TP-Link TL-WR1043ND v2
[    0.000000] SoC: Qualcomm Atheros QCA9558 ver 1 rev 0
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 16240
[    0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,jffs2
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes, linear)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 57408K/65536K available (4753K kernel code, 183K rwdata, 1100K rodata, 1188K init, 196K bss, 8128K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS: 51
[    0.000000] random: get_random_bytes called from start_kernel+0x32c/0x518 with crng_init=0
[    0.000000] CPU clock: 720.000 MHz
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 5309056796 ns
[    0.000007] sched_clock: 32 bits at 360MHz, resolution 2ns, wraps every 5965232126ns
[    0.008304] Calibrating delay loop... 359.42 BogoMIPS (lpj=718848)
[    0.042895] pid_max: default: 32768 minimum: 301
[    0.047939] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.055731] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.068023] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.078401] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[    0.085760] pinctrl core: initialized pinctrl subsystem
[    0.092269] NET: Registered protocol family 16
[    0.125112] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512
[    0.138512] clocksource: Switched to clocksource MIPS
[    0.145000] NET: Registered protocol family 2
[    0.150412] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[    0.159383] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.167556] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.175076] TCP: Hash tables configured (established 1024 bind 1024)
[    0.181978] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[    0.188984] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[    0.196689] NET: Registered protocol family 1
[    0.201403] PCI: CLS 0 bytes, default 32
[    0.209179] workingset: timestamp_bits=14 max_order=14 bucket_order=0
[    0.222121] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.228370] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.253702] pinctrl-single 1804002c.pinmux: 544 pins, size 68
[    0.260356] gpio-export gpio-export: 1 gpio(s) exported
[    0.266791] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    0.274237] printk: console [ttyS0] disabled
[    0.278880] 18020000.uart: ttyS0 at MMIO 0x18020000 (irq = 9, base_baud = 2500000) is a 16550A
[    0.288078] printk: console [ttyS0] enabled
[    0.288078] printk: console [ttyS0] enabled
[    0.296983] printk: bootconsole [early0] disabled
[    0.296983] printk: bootconsole [early0] disabled
[    0.326653] spi-nor spi0.0: s25fl064k (8192 Kbytes)
[    0.331659] 3 fixed-partitions partitions found on MTD device spi0.0
[    0.338114] Creating 3 MTD partitions on "spi0.0":
[    0.342997] 0x000000000000-0x000000020000 : "u-boot"
[    0.348955] 0x000000020000-0x0000007f0000 : "firmware"
[    0.356886] 2 tplink-fw partitions found on MTD device firmware
[    0.362955] Creating 2 MTD partitions on "firmware":
[    0.368020] 0x000000000000-0x0000001e7881 : "kernel"
[    0.373908] 0x0000001e7884-0x0000007d0000 : "rootfs"
[    0.379757] mtd: device 3 (rootfs) set to be root filesystem
[    0.387289] 1 squashfs-split partitions found on MTD device rootfs
[    0.393628] 0x0000004b0000-0x0000007d0000 : "rootfs_data"
[    0.399977] 0x0000007f0000-0x000000800000 : "art"
[    0.407475] libphy: Fixed MDIO Bus: probed
[    0.744356] libphy: ag71xx_mdio: probed
[    0.751255] switch0: Atheros AR8327 rev. 4 switch registered on mdio.0
[    1.138505] random: fast init done
[    1.335866] ag71xx 19000000.eth: connected to PHY at mdio.0:00 [uid=004dd034, driver=Atheros AR8216/AR8236/AR8316]
[    1.346964] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode: rgmii
[    1.668297] ag71xx 1a000000.eth: connected to PHY at fixed-0:00 [uid=00000000, driver=Generic PHY]
[    1.678016] eth1: Atheros AG71xx at 0xba000000, irq 5, mode: sgmii
[    1.684519] i2c /dev entries driver
[    1.690083] NET: Registered protocol family 10
[    1.699644] Segment Routing with IPv6
[    1.703525] NET: Registered protocol family 17
[    1.708120] 8021q: 802.1Q VLAN Support v1.8
[    1.718966] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[    1.732581] Freeing unused kernel memory: 1188K
[    1.737201] This architecture does not have kernel memory protection.
[    1.743742] Run /sbin/init as init process
Error loading shared library libubox.so: No such file or directory (needed by /sbin/init)
Error loading shared library libubus.so: No such file or directory (needed by /sbin/init)
Error loading shared library libjson-c.so.5: No such file or directory (needed by /sbin/init)
Error loading shared library libblobmsg_json.so: No such file or directory (needed by /sbin/init)
Error loading shared library libjson_script.so: No such file or directory (needed by /sbin/init)
Error relocating[    2.195702] Kernel panic - not syncing: Attempted to kill init! exitcode=0x00007f00
[    2.204495] Rebooting in 1 seconds..


U-Boot 1.1.4 (Jun 18 2013 - 15:51:52)

The libs are built correctly:

risa@gentoo-vb ~/openwrt/openwrt $ ldd staging_dir/host/bin/ucert
        linux-vdso.so.1 (0x00007ffcd6db2000)
        libubox.so => /home/risa/openwrt/openwrt/staging_dir/host/lib/libubox.so (0x00007f914f60e000)
        libblobmsg_json.so => /home/risa/openwrt/openwrt/staging_dir/host/lib/libblobmsg_json.so (0x00007f914f609000)
        libjson-c.so.5 => /home/risa/openwrt/openwrt/staging_dir/host/lib/libjson-c.so.5 (0x00007f914f5f6000)
        libc.so.6 => /lib64/libc.so.6 (0x00007f914f433000)
        /lib64/ld-linux-x86-64.so.2 (0x00007f914f626000)
risa@gentoo-vb ~/openwrt/openwrt $ ls -la /home/risa/openwrt/openwrt/staging_dir/host/lib/libubox.so
-rwxr-xr-x 1 risa risa 417040 Oct 31 23:25 /home/risa/openwrt/openwrt/staging_dir/host/lib/libubox.so
risa@gentoo-vb ~/openwrt/openwrt $ ls -la /home/risa/openwrt/openwrt/staging_dir/host/lib/libblobmsg_json.so
-rwxr-xr-x 1 risa risa 115704 Oct 31 23:25 /home/risa/openwrt/openwrt/staging_dir/host/lib/libblobmsg_json.so
risa@gentoo-vb ~/openwrt/openwrt $ ls -la /home/risa/openwrt/openwrt/staging_dir/host/lib/libjson-c.so.5
lrwxrwxrwx 1 risa risa 18 Oct 31 23:24 /home/risa/openwrt/openwrt/staging_dir/host/lib/libjson-c.so.5 -> libjson-c.so.5.1.0
risa@gentoo-vb ~/openwrt/openwrt $ ls -la ./staging_dir/target-mips_24kc_musl/usr/lib/libubus.so
-rwxr-xr-x 1 risa risa 146900 Oct 31 23:27 ./staging_dir/target-mips_24kc_musl/usr/lib/libubus.so

but for some reason are not present in the final image built from ImageBuilder.

The image built using the same configuration from the older revision (7190fb2da4) has the size:

-rw-r--r--  1 risa risa 6684973 Sep 20 15:46 openwrt-ath79-generic-tplink_tl-wr1043nd-v2-squashfs-sysupgrade.bin

while the new one built now is much smaller. It looks like some parts are not correctly stored in the image:

-rw-r--r--  1 risa risa 4915501 Oct 31 23:46 openwrt-ath79-generic-tplink_tl-wr1043nd-v2-squashfs-sysupgrade.bin


01.11.20203423Base systemBug ReportVery LowHighNo dependencies installed and configuredTrunkUnconfirmed Task Description

Supply the following if possible:
- Device problem occurs on
- Software versions of OpenWrt/LEDE release, packages, etc.
- Steps to reproduce

 

root@OpenWrt:~# opkg install luci
Installing luci (git-20.304.73778-5a485f8) to root...
Downloading https://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci_git-20.304.73778-5a485f8_all.ipk Configuring luci.
root@OpenWrt:~# opkg list-installed | grep luci
luci - git-20.304.73778-5a485f8

On a fresh install, no dependencies installed and configured, leading to an non functional Luci instance.

On the lastest snapshots, with my Linksys EA7500 V1.

08.11.20203439Base systemBug ReportVery LowHighCan't connect for WPA2-Enterprise from Windows system.openwrt-19.07Unconfirmed Task Description

Supply the following if possible:
- Device problem occurs on
- Software versions of OpenWrt/LEDE release, packages, etc.
- Steps to reproduce

Device problem occurs on

I can’t connect to network wifi (WPA2-Enterprise) from Windows system. I can connect from Linux and IOS systems.
I tested packages: wpad-mesh-openssl, wpad-openssl, wpad-wolfssl and wpad.

Software versions of OpenWrt/LEDE release, packages, etc

cat /etc/openwrt_release
DISTRIB_ID=’OpenWrt’ DISTRIB_RELEASE=’19.07-SNAPSHOT’ DISTRIB_REVISION=’r11201-f5afa593e7’ DISTRIB_TARGET=’ath79/generic’ DISTRIB_ARCH=’mips_24kc’ DISTRIB_DESCRIPTION=’OpenWrt 19.07-SNAPSHOT r11201-f5afa593e7’ DISTRIB_TAINTS=’’

opkg list-installed
adblock - 4.0.6-3
base-files - 204.2-r11201-f5afa593e7
blkid - 2.34-1
block-mount - 2020-05-12-84269037-1
busybox - 1.30.1-6
ca-bundle - 20200601-1
cgi-io - 19
chat - 2.4.7.git-2019-05-25-3
comgt - 0.32-32
comgt-directip - 0.32-32
comgt-ncm - 0.32-32
coreutils - 8.30-2
coreutils-sort - 8.30-2
ddns-scripts - 2.7.8-13
dnsmasq - 2.80-16.1
dropbear - 2019.78-2
e2fsprogs - 1.44.5-2
ekooneplstat - 20150706
etherwake - 1.09-4
firewall - 2019-11-22-8174814a-2
fstools - 2020-05-12-84269037-1
fwtool - 2
getrandom - 2019-06-16-4df34a4d-3
hostapd-common - 2019-08-08-ca8c2bd2-4
ip-tiny - 5.0.0-2.1
ipset - 7.3-1
iptables - 1.8.3-1
iw - 5.0.1-1
iwinfo - 2019-10-16-07315b6f-1
jshn - 2020-05-25-66195aee-1
jsonfilter - 2018-02-04-c7e938d6-1
kernel - 4.14.195-1-38fe082385c94876bc5af35c67d5656a
kmod-ath - 4.14.195+4.19.137-1-2
kmod-ath9k - 4.14.195+4.19.137-1-2
kmod-ath9k-common - 4.14.195+4.19.137-1-2
kmod-cfg80211 - 4.14.195+4.19.137-1-2
kmod-crypto-aead - 4.14.195-1
kmod-crypto-ccm - 4.14.195-1
kmod-crypto-cmac - 4.14.195-1
kmod-crypto-crc32c - 4.14.195-1
kmod-crypto-ctr - 4.14.195-1
kmod-crypto-des - 4.14.195-1
kmod-crypto-ecb - 4.14.195-1
kmod-crypto-gcm - 4.14.195-1
kmod-crypto-gf128 - 4.14.195-1
kmod-crypto-ghash - 4.14.195-1
kmod-crypto-hash - 4.14.195-1
kmod-crypto-hmac - 4.14.195-1
kmod-crypto-iv - 4.14.195-1
kmod-crypto-manager - 4.14.195-1
kmod-crypto-md4 - 4.14.195-1
kmod-crypto-md5 - 4.14.195-1
kmod-crypto-null - 4.14.195-1
kmod-crypto-pcompress - 4.14.195-1
kmod-crypto-rng - 4.14.195-1
kmod-crypto-seqiv - 4.14.195-1
kmod-crypto-sha256 - 4.14.195-1
kmod-crypto-sha512 - 4.14.195-1
kmod-crypto-wq - 4.14.195-1
kmod-fs-ext4 - 4.14.195-1
kmod-fs-ksmbd - 4.14.195+3.1.3-1
kmod-fs-vfat - 4.14.195-1
kmod-fuse - 4.14.195-1
kmod-gpio-button-hotplug - 4.14.195-3
kmod-ipt-conntrack - 4.14.195-1
kmod-ipt-core - 4.14.195-1
kmod-ipt-ipset - 4.14.195-1
kmod-ipt-nat - 4.14.195-1
kmod-ipt-offload - 4.14.195-1
kmod-ipt-raw - 4.14.195-1
kmod-lib-crc-ccitt - 4.14.195-1
kmod-lib-crc16 - 4.14.195-1
kmod-lib-textsearch - 4.14.195-1
kmod-mac80211 - 4.14.195+4.19.137-1-2
kmod-mii - 4.14.195-1
kmod-nf-conntrack - 4.14.195-1
kmod-nf-conntrack6 - 4.14.195-1
kmod-nf-flow - 4.14.195-1
kmod-nf-ipt - 4.14.195-1
kmod-nf-ipt6 - 4.14.195-1
kmod-nf-nat - 4.14.195-1
kmod-nf-nathelper-extra - 4.14.195-1
kmod-nf-reject - 4.14.195-1
kmod-nf-reject6 - 4.14.195-1
kmod-nfnetlink - 4.14.195-1
kmod-nls-base - 4.14.195-1
kmod-nls-cp437 - 4.14.195-1
kmod-nls-iso8859-1 - 4.14.195-1
kmod-nls-utf8 - 4.14.195-1
kmod-phy-ath79-usb - 4.14.195-1
kmod-ppp - 4.14.195-1
kmod-pppoe - 4.14.195-1
kmod-pppox - 4.14.195-1
kmod-scsi-core - 4.14.195-1
kmod-slhc - 4.14.195-1
kmod-tun - 4.14.195-1
kmod-udptunnel4 - 4.14.195-1
kmod-udptunnel6 - 4.14.195-1
kmod-usb-acm - 4.14.195-1
kmod-usb-core - 4.14.195-1
kmod-usb-ehci - 4.14.195-1
kmod-usb-ledtrig-usbport - 4.14.195-1
kmod-usb-net - 4.14.195-1
kmod-usb-net-cdc-ether - 4.14.195-1
kmod-usb-net-cdc-mbim - 4.14.195-1
kmod-usb-net-cdc-ncm - 4.14.195-1
kmod-usb-net-huawei-cdc-ncm - 4.14.195-1
kmod-usb-net-qmi-wwan - 4.14.195-1
kmod-usb-net-rndis - 4.14.195-1
kmod-usb-net-sierrawireless - 4.14.195-1
kmod-usb-serial - 4.14.195-1
kmod-usb-serial-option - 4.14.195-1
kmod-usb-serial-qualcomm - 4.14.195-1
kmod-usb-serial-sierrawireless - 4.14.195-1
kmod-usb-serial-wwan - 4.14.195-1
kmod-usb-storage - 4.14.195-1
kmod-usb-storage-uas - 4.14.195-1
kmod-usb-wdm - 4.14.195-1
kmod-usb2 - 4.14.195-1
kmod-wireguard - 4.14.195+1.0.20200611-1
ksmbd-server - 3.2.1-1
ksmbd-utils - 3.2.1-1
libblkid1 - 2.34-1
libblobmsg-json - 2020-05-25-66195aee-1
libc - 1.1.24-2
libcomerr0 - 1.44.5-2
libext2fs2 - 1.44.5-2
libgcc1 - 7.5.0-2
libip4tc2 - 1.8.3-1
libip6tc2 - 1.8.3-1
libipset13 - 7.3-1
libiwinfo-lua - 2019-10-16-07315b6f-1
libiwinfo20181126 - 2019-10-16-07315b6f-1
libjson-c2 - 0.12.1-3.1
libjson-script - 2020-05-25-66195aee-1
liblua5.1.5 - 5.1.5-3
liblucihttp-lua - 2019-07-05-a34a17d5-1
liblucihttp0 - 2019-07-05-a34a17d5-1
liblzo2 - 2.10-2
libmbedtls12 - 2.16.8-1
libmnl0 - 1.0.4-2
libncurses6 - 6.1-5
libnl-core200 - 3.4.0-2
libnl-genl200 - 3.4.0-2
libnl-tiny - 0.1-5
libopenssl-conf - 1.1.1g-1
libopenssl1.1 - 1.1.1g-1
libpcap1 - 1.9.1-2.1
libpcre - 8.43-1
libpthread - 1.1.24-2
librt - 1.1.24-2
libss2 - 1.44.5-2
libubox20191228 - 2020-05-25-66195aee-1
libubus-lua - 2019-12-27-041c9d1c-1
libubus20191227 - 2019-12-27-041c9d1c-1
libuci20130104 - 2019-09-01-415f9e48-3
libuclient20160123 - 2020-06-17-51e16ebf-1
libusb-1.0-0 - 1.0.22-2
libustream-openssl20150806 - 2020-03-13-40b563b1-1
libuuid1 - 2.34-1
libwolfssl24 - 4.5.0-stable-1
libxtables12 - 1.8.3-1
logd - 2019-06-16-4df34a4d-3
lua - 5.1.5-3
luci - git-20.247.75781-0d0ab01-1
luci-app-adblock - git-20.247.75781-0d0ab01-1
luci-app-commands - git-20.247.75781-0d0ab01-1
luci-app-ddns - 2.4.9-7
luci-app-ekooneplstat - 20190629
luci-app-firewall - git-20.247.75781-0d0ab01-1
luci-app-ksmbd - git-20.247.75781-0d0ab01-1
luci-app-openvpn - git-20.247.75781-0d0ab01-1
luci-app-opkg - git-20.247.75781-0d0ab01-1
luci-app-p910nd - git-20.247.75781-0d0ab01-1
luci-app-vpnbypass - git-20.247.75781-0d0ab01-19
luci-app-wifischedule - git-20.247.75781-0d0ab01-1
luci-app-wireguard - git-20.247.75781-0d0ab01-1
luci-app-wol - git-20.247.75781-0d0ab01-1
luci-base - git-20.247.75781-0d0ab01-1
luci-compat - git-20.247.75781-0d0ab01-1
luci-i18n-adblock-en - git-20.247.75781-0d0ab01-1
luci-i18n-adblock-pl - git-20.247.75781-0d0ab01-1
luci-i18n-base-en - git-20.247.75781-0d0ab01-1
luci-i18n-base-pl - git-20.247.75781-0d0ab01-1
luci-i18n-commands-en - git-20.247.75781-0d0ab01-1
luci-i18n-commands-pl - git-20.247.75781-0d0ab01-1
luci-i18n-ddns-en - 2.4.9-7
luci-i18n-ddns-pl - 2.4.9-7
luci-i18n-firewall-en - git-20.247.75781-0d0ab01-1
luci-i18n-firewall-pl - git-20.247.75781-0d0ab01-1
luci-i18n-ksmbd-en - git-20.247.75781-0d0ab01-1
luci-i18n-ksmbd-pl - git-20.247.75781-0d0ab01-1
luci-i18n-openvpn-en - git-20.247.75781-0d0ab01-1
luci-i18n-openvpn-pl - git-20.247.75781-0d0ab01-1
luci-i18n-opkg-en - git-20.247.75781-0d0ab01-1
luci-i18n-opkg-pl - git-20.247.75781-0d0ab01-1
luci-i18n-p910nd-en - git-20.247.75781-0d0ab01-1
luci-i18n-p910nd-pl - git-20.247.75781-0d0ab01-1
luci-i18n-vpnbypass-en - git-20.247.75781-0d0ab01-19
luci-i18n-vpnbypass-pl - git-20.247.75781-0d0ab01-19
luci-i18n-wifischedule-en - git-20.247.75781-0d0ab01-1
luci-i18n-wifischedule-pl - git-20.247.75781-0d0ab01-1
luci-i18n-wireguard-en - git-20.247.75781-0d0ab01-1
luci-i18n-wireguard-pl - git-20.247.75781-0d0ab01-1
luci-i18n-wol-en - git-20.247.75781-0d0ab01-1
luci-i18n-wol-pl - git-20.247.75781-0d0ab01-1
luci-lib-ip - git-20.247.75781-0d0ab01-1
luci-lib-ipkg - git-20.247.75781-0d0ab01-1
luci-lib-jsonc - git-20.247.75781-0d0ab01-1
luci-lib-nixio - git-20.247.75781-0d0ab01-1
luci-mod-admin-full - git-20.247.75781-0d0ab01-1
luci-mod-network - git-20.247.75781-0d0ab01-1
luci-mod-status - git-20.247.75781-0d0ab01-1
luci-mod-system - git-20.247.75781-0d0ab01-1
luci-proto-3g - git-20.247.75781-0d0ab01-1
luci-proto-ipv6 - git-20.247.75781-0d0ab01-1
luci-proto-ncm - git-20.247.75781-0d0ab01-1
luci-proto-ppp - git-20.247.75781-0d0ab01-1
luci-proto-qmi - git-20.247.75781-0d0ab01-1
luci-proto-relay - git-20.247.75781-0d0ab01-1
luci-proto-wireguard - git-20.247.75781-0d0ab01-1
luci-ssl-openssl - git-20.247.75781-0d0ab01-1
luci-theme-bootstrap - git-20.247.75781-0d0ab01-1
mbedtls-util - 2.16.8-1
mtd - 24
netifd - 2019-08-05-5e02f944-1
ntfs-3g - 2017.3.23-2-fuseint
odhcpd-ipv6only - 2020-05-03-49e4949c-3
openssh-sftp-server - 8.0p1-1
openssl-util - 1.1.1g-1
openvpn-easy-rsa - 3.0.4-1
openvpn-openssl - 2.4.7-2
openwrt-keyring - 2019-07-25-8080ef34-1
opkg - 2020-05-07-f2166a89-1
p910nd - 0.97-8
port-mirroring - 1.4.4-2
ppp - 2.4.7.git-2019-05-25-3
ppp-mod-pppoe - 2.4.7.git-2019-05-25-3
procd - 2020-03-07-09b9bd82-1
relayd - 2020-04-25-f4d759be-1
rpcd - 2020-05-26-67c8a3fd-1
rpcd-mod-file - 2020-05-26-67c8a3fd-1
rpcd-mod-iwinfo - 2020-05-26-67c8a3fd-1
rpcd-mod-luci - 20191114
rpcd-mod-rrdns - 20170710
screen - 4.8.0-1
swconfig - 12
sysinfo - 20200403
terminfo - 6.1-5
uboot-envtools - 2018.03-3
ubox - 2019-06-16-4df34a4d-3
ubus - 2019-12-27-041c9d1c-1
ubusd - 2019-12-27-041c9d1c-1
uci - 2019-09-01-415f9e48-3
uclient-fetch - 2020-06-17-51e16ebf-1
uhttpd - 2020-03-13-975dce23-1
umbim - 2019-03-11-24f9dc71-1
uqmi - 2019-06-27-1965c713-7
urandom-seed - 1.0-1
urngd - 2020-01-21-c7f7b6b6-1
usb-modeswitch - 2017-12-19-f40f84c2-2
usign - 2020-05-23-f1f65026-1
vpnbypass - 1.3.1-7
wget - 1.20.3-4
wifischedule - 1-2
wireguard-tools - 1.0.20191226-1
wireless-regdb - 2019.06.03-1
wpad-mesh-openssl - 2019-08-08-ca8c2bd2-4
wsdd2 - 2020-05-06-671d040c-1
wwan - 2014-07-17-1
xinetd - 2.3.15-5
zlib - 1.2.11-3

cat /etc/config/wireless
config wifi-device ‘radio1’

  option type 'mac80211'
  option channel '36'
  option hwmode '11a'
  option path 'pci0000:00/0000:00:00.0'
  option htmode 'HT20'
  option country 'PL'


config wifi-iface ‘default_radio1’

  option device 'radio1'
  option network 'lan'
  option mode 'ap'
  option auth_server '192.168.1.X'
  option auth_port '1812'
  option auth_secret password
  option ssid 'name'
  option encryption 'wpa2+ccmp'
  option wpa_disable_eapol_key_retries '1'
  option ieee80211w '2'
  option disassoc_low_ack '0'

Steps to reproduce

Always when I tried connect to wireless network from Windows system I can’t connect to network and I saw below logs:

logread | grep wlan1
Sun Nov 8 21:54:54 2020 daemon.info hostapd: wlan1: STA MAC ADDRESS IEEE 802.11: authenticated
Sun Nov 8 21:54:54 2020 daemon.info hostapd: wlan1: STA MAC ADDRESS IEEE 802.11: associated (aid 2)
Sun Nov 8 21:54:54 2020 daemon.notice hostapd: wlan1: CTRL-EVENT-EAP-STARTED MAC ADDRESS
Sun Nov 8 21:54:54 2020 daemon.notice hostapd: wlan1: CTRL-EVENT-EAP-PROPOSED-METHOD vendor=0 method=1
Sun Nov 8 21:54:55 2020 daemon.notice hostapd: wlan1: CTRL-EVENT-EAP-STARTED MAC ADDRESS
Sun Nov 8 21:54:55 2020 daemon.notice hostapd: wlan1: CTRL-EVENT-EAP-PROPOSED-METHOD vendor=0 method=1
Sun Nov 8 21:54:56 2020 daemon.warn hostapd: wlan1: STA MAC ADDRESS IEEE 802.1X: could not extract EAP-Message from RADIUS message
Sun Nov 8 21:54:56 2020 daemon.notice hostapd: wlan1: CTRL-EVENT-EAP-FAILURE2 MAC ADDRESS
Sun Nov 8 21:54:56 2020 daemon.warn hostapd: wlan1: STA MAC ADDRESS IEEE 802.1X: authentication failed - EAP type: 0 (unknown)
Sun Nov 8 21:54:56 2020 daemon.info hostapd: wlan1: STA MAC ADDRESS IEEE 802.1X: Supplicant used different EAP type: 1 (Identity)
Sun Nov 8 21:55:01 2020 daemon.info hostapd: wlan1: STA MAC ADDRESS IEEE 802.11: deauthenticated due to local deauth request
Sun Nov 8 21:55:03 2020 daemon.info hostapd: wlan1: STA MAC ADDRESS IEEE 802.11: authenticated
Sun Nov 8 21:55:03 2020 daemon.info hostapd: wlan1: STA MAC ADDRESS IEEE 802.11: associated (aid 2)
Sun Nov 8 21:55:03 2020 daemon.notice hostapd: wlan1: CTRL-EVENT-EAP-STARTED MAC ADDRESS
Sun Nov 8 21:55:03 2020 daemon.notice hostapd: wlan1: CTRL-EVENT-EAP-PROPOSED-METHOD vendor=0 method=1
Sun Nov 8 21:55:03 2020 daemon.notice hostapd: wlan1: CTRL-EVENT-EAP-STARTED MAC ADDRESS
Sun Nov 8 21:55:03 2020 daemon.notice hostapd: wlan1: CTRL-EVENT-EAP-PROPOSED-METHOD vendor=0 method=1
Sun Nov 8 21:55:04 2020 daemon.warn hostapd: wlan1: STA MAC ADDRESS IEEE 802.1X: could not extract EAP-Message from RADIUS message
Sun Nov 8 21:55:04 2020 daemon.notice hostapd: wlan1: CTRL-EVENT-EAP-FAILURE2 MAC ADDRESS
Sun Nov 8 21:55:04 2020 daemon.warn hostapd: wlan1: STA MAC ADDRESS IEEE 802.1X: authentication failed - EAP type: 0 (unknown)
Sun Nov 8 21:55:04 2020 daemon.info hostapd: wlan1: STA MAC ADDRESS IEEE 802.1X: Supplicant used different EAP type: 1 (Identity)
Sun Nov 8 21:55:09 2020 daemon.info hostapd: wlan1: STA MAC ADDRESS IEEE 802.11: deauthenticated due to local deauth request

This problem occurred after upgrade openwrt system.

23.12.20203530Base systemBug ReportVery LowHighD-Link DIR-645 not maintaining WLAN connectionopenwrt-19.07Unconfirmed Task Description

- Device problem occurs on
D-Link DIR-645 Rev. A1

- Software versions of OpenWrt/LEDE release, packages, etc.
LEDE 19.07.4

- Steps to reproduce
Setup the wireless connection. After some time the WLAN connection stops working. A restart is necessary to regain WLAN.

Topic is discussed in the forums:
https://forum.lede-project.org/t/d-link-dir-645-wifi-interface-not-maintaining-connection/6277

I am able and willing to provide log files. But I am new to the business of debugging itself. Help and guidance welcome!

Reference links:
https://forum.lede-project.org/t/d-link-dir-645-wifi-interface-not-maintaining-connection/6277 https://forum.openwrt.org/t/assistance-needed-debugging-wlan-d-link-dir-645/18664

25.12.20203533Base systemBug ReportVery LowHighrelayd can't relay packets between lan pc and the openw...TrunkUnconfirmed Task Description

Supply the following if possible:
- Device problem occurs on MediaTek MT7620A ver:2 eco:6
- Software versions

  URL: https://github.com/openwrt/openwrt.git/trunk
  Relative URL: ^/trunk
  Repository Root: https://github.com/openwrt/openwrt.git
  Repository UUID: 48f6a8c1-d3d8-b121-14bd-ce57b7db7bff
  Revision: 92580

- Steps to reproduce

 1. add wifi client
 2. add relay bridge interface between wlan and lan
 3. the wlan interface get ip 192.168.3.136, the pc in lan get ip 192.168.3.128, the ip of root ap was 192.168.3.1
 4. the pc can ping 192.168.3.1 but can not ping 192.168.3.136


30.12.20203545Base systemBug ReportVery LowHighunusable channels 13, 12 & auto on raspberry pi 3b & ze...openwrt-19.07Unconfirmed Task Description

Channels 13, 12 and auto are unusuable despite a valid CRDA selection (PL).

Lack of functional support for channels 13 & 12 where those are legally available renders OpenWrt unusable as AP/client on raspberry pi 3 & zero w. Both share the same BRCM 43430 driver.

Auto selection is also crippled:
Wed Dec 30 04:16:49 2020 daemon.warn hostapd: wlan0: IEEE 802.11 Configured channel (0) not found from the channel list of current mode (1) IEEE 802.11g
Wed Dec 30 04:16:49 2020 daemon.warn hostapd: wlan0: IEEE 802.11 Hardware does not support configured channel

Both would be a showstopper. OpenWrt on such platforms is often picked for its AP capabilities.

+ iw reg get
global
country PL: DFS-ETSI
        (2400 - 2483 @ 40), (N/A, 20), (N/A)
        (5150 - 5250 @ 80), (N/A, 23), (N/A), NO-OUTDOOR, AUTO-BW
        (5250 - 5350 @ 80), (N/A, 20), (0 ms), NO-OUTDOOR, DFS, AUTO-BW
        (5470 - 5725 @ 160), (N/A, 26), (0 ms), DFS
        (5725 - 5875 @ 80), (N/A, 13), (N/A)
        (57000 - 66000 @ 2160), (N/A, 40), (N/A)

+ uci show wireless
wireless.radio0=wifi-device
wireless.radio0.type='mac80211'
wireless.radio0.hwmode='11g'
wireless.radio0.path='platform/soc/3f300000.mmc/mmc_host/mmc1/mmc1:0001/mmc1:0001:1'
wireless.radio0.legacy_rates='0'
wireless.radio0.country='PL'
wireless.radio0.htmode='HT20'
wireless.radio0.channel='11'
wireless.default_radio0=wifi-iface
wireless.default_radio0.device='radio0'
wireless.default_radio0.network='lan'
wireless.default_radio0.mode='ap'
wireless.default_radio0.ssid='my_ssid'
wireless.default_radio0.wpa_disable_eapol_key_retries='1'
wireless.default_radio0.key='my_key'
wireless.default_radio0.hidden='1'
wireless.default_radio0.encryption='psk2'
+ uci set 'wireless.radio0.channel=13'
+ uci commit wireless
+ sleep 1
+ logread -f
+ logger start testing channel 13
+ wifi
Wed Dec 30 04:16:41 2020 user.notice root: start testing channel 13
+ sleep 3
Wed Dec 30 04:16:41 2020 daemon.notice hostapd: wlan0: interface state ENABLED->DISABLED
Wed Dec 30 04:16:41 2020 daemon.notice hostapd: wlan0: AP-STA-DISCONNECTED MAC_ADDRESS_WAS_HERE
Wed Dec 30 04:16:41 2020 daemon.notice hostapd: wlan0: AP-STA-DISCONNECTED MAC_ADDRESS_WAS_HERE
Wed Dec 30 04:16:41 2020 daemon.notice hostapd: wlan0: AP-STA-DISCONNECTED MAC_ADDRESS_WAS_HERE
Wed Dec 30 04:16:41 2020 daemon.notice hostapd: wlan0: AP-DISABLED
Wed Dec 30 04:16:41 2020 daemon.notice hostapd: wlan0: CTRL-EVENT-TERMINATING
Wed Dec 30 04:16:41 2020 daemon.notice hostapd: nl80211: deinit ifname=wlan0 disabled_11b_rates=0
Wed Dec 30 04:16:41 2020 daemon.notice netifd: Network device 'wlan0' link is down
Wed Dec 30 04:16:41 2020 daemon.notice netifd: Interface 'lan' has link connectivity loss
Wed Dec 30 04:16:42 2020 daemon.notice netifd: radio0 (8589): command failed: No error information (-524)
Wed Dec 30 04:16:42 2020 user.notice mac80211: Failed command: iw dev wlan0 del
Wed Dec 30 04:16:42 2020 daemon.notice netifd: Interface 'lan' is now down
Wed Dec 30 04:16:42 2020 daemon.notice netifd: Interface 'lan' is disabled
Wed Dec 30 04:16:42 2020 daemon.notice netifd: radio0 (8612): command failed: No error information (-524)
Wed Dec 30 04:16:42 2020 user.notice mac80211: Failed command: iw dev wlan0 del
Wed Dec 30 04:16:42 2020 user.notice mac80211: Failed command: iw phy phy0 set antenna 0xffffffff 0xffffffff
Wed Dec 30 04:16:42 2020 daemon.notice netifd: radio0 (8612): command failed: Not supported (-95)
Wed Dec 30 04:16:42 2020 user.notice mac80211: Failed command: iw phy phy0 set antenna_gain 0
Wed Dec 30 04:16:42 2020 daemon.notice netifd: radio0 (8612): command failed: I/O error (-5)
Wed Dec 30 04:16:42 2020 user.notice mac80211: Failed command: iw phy phy0 set distance 0
Wed Dec 30 04:16:42 2020 daemon.notice netifd: radio0 (8612): command failed: Too many open files in system (-23)
Wed Dec 30 04:16:42 2020 user.notice mac80211: Failed command: iw phy phy0 interface add wlan0 type __ap
Wed Dec 30 04:16:42 2020 daemon.err hostapd: Configuration file: /var/run/hostapd-phy0.conf
Wed Dec 30 04:16:42 2020 daemon.notice hostapd: wlan0: interface state UNINITIALIZED->COUNTRY_UPDATE
Wed Dec 30 04:16:42 2020 kern.info kernel: [ 8810.101885] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
Wed Dec 30 04:16:42 2020 daemon.warn hostapd: wlan0: Could not connect to kernel driver
Wed Dec 30 04:16:42 2020 daemon.err hostapd: Using interface wlan0 with hwaddr MAC_ADDRESS_WAS_HERE and ssid "my_ssid"
Wed Dec 30 04:16:42 2020 daemon.err hostapd: Failed to set beacon parameters
Wed Dec 30 04:16:42 2020 daemon.warn hostapd: wlan0: Could not connect to kernel driver
Wed Dec 30 04:16:42 2020 daemon.err hostapd: Interface initialization failed
Wed Dec 30 04:16:42 2020 daemon.notice hostapd: wlan0: interface state COUNTRY_UPDATE->DISABLED
Wed Dec 30 04:16:42 2020 daemon.notice hostapd: wlan0: AP-DISABLED
Wed Dec 30 04:16:42 2020 daemon.err hostapd: wlan0: Unable to setup interface.
Wed Dec 30 04:16:42 2020 daemon.notice hostapd: wlan0: interface state DISABLED->DISABLED
Wed Dec 30 04:16:42 2020 daemon.notice hostapd: wlan0: AP-DISABLED
Wed Dec 30 04:16:42 2020 daemon.notice hostapd: wlan0: CTRL-EVENT-TERMINATING
Wed Dec 30 04:16:42 2020 daemon.err hostapd: hostapd_free_hapd_data: Interface wlan0 wasn't started
Wed Dec 30 04:16:42 2020 daemon.notice hostapd: nl80211: deinit ifname=wlan0 disabled_11b_rates=0
Wed Dec 30 04:16:42 2020 kern.err kernel: [ 8810.195905] ieee80211 phy0: brcmf_cfg80211_start_ap: Set Channel failed: chspec=4109, -52
Wed Dec 30 04:16:43 2020 daemon.notice hostapd: ELOOP: remaining socket: sock=22 eloop_data=0x7fb0bb4e60 user_data=0 handler=0x41d078
Wed Dec 30 04:16:43 2020 daemon.notice netifd: radio0 (8612): WARNING (wireless_add_process): executable path /usr/sbin/wpad does not match process 8118 path ()
Wed Dec 30 04:16:43 2020 daemon.notice netifd: radio0 (8612): Device setup failed: HOSTAPD_START_FAILED
Wed Dec 30 04:16:43 2020 daemon.info dnsmasq[8225]: exiting on receipt of SIGTERM
Wed Dec 30 04:16:43 2020 daemon.info dnsmasq[8765]: started, version 2.80 cachesize 150
Wed Dec 30 04:16:43 2020 daemon.info dnsmasq[8765]: DNS service limited to local subnets
Wed Dec 30 04:16:43 2020 daemon.info dnsmasq[8765]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth no-DNSSEC no-ID loop-detect inotify dumpfile
Wed Dec 30 04:16:43 2020 daemon.info dnsmasq[8765]: using local addresses only for domain test
Wed Dec 30 04:16:43 2020 daemon.info dnsmasq[8765]: using local addresses only for domain onion
Wed Dec 30 04:16:43 2020 daemon.info dnsmasq[8765]: using local addresses only for domain localhost
Wed Dec 30 04:16:43 2020 daemon.info dnsmasq[8765]: using local addresses only for domain local
Wed Dec 30 04:16:43 2020 daemon.info dnsmasq[8765]: using local addresses only for domain invalid
Wed Dec 30 04:16:43 2020 daemon.info dnsmasq[8765]: using local addresses only for domain bind
Wed Dec 30 04:16:43 2020 daemon.info dnsmasq[8765]: using local addresses only for domain lan
Wed Dec 30 04:16:43 2020 daemon.info dnsmasq[8765]: reading /tmp/resolv.conf.auto
Wed Dec 30 04:16:43 2020 daemon.info dnsmasq[8765]: using local addresses only for domain test
Wed Dec 30 04:16:43 2020 daemon.info dnsmasq[8765]: using local addresses only for domain onion
Wed Dec 30 04:16:43 2020 daemon.info dnsmasq[8765]: using local addresses only for domain localhost
Wed Dec 30 04:16:43 2020 daemon.info dnsmasq[8765]: using local addresses only for domain local
Wed Dec 30 04:16:43 2020 daemon.info dnsmasq[8765]: using local addresses only for domain invalid
Wed Dec 30 04:16:43 2020 daemon.info dnsmasq[8765]: using local addresses only for domain bind
Wed Dec 30 04:16:43 2020 daemon.info dnsmasq[8765]: using local addresses only for domain lan
Wed Dec 30 04:16:43 2020 daemon.info dnsmasq[8765]: using nameserver IP_ADDRESS_WAS_HERE#53
Wed Dec 30 04:16:43 2020 daemon.info dnsmasq[8765]: using nameserver IP_ADDRESS_WAS_HERE#53
Wed Dec 30 04:16:43 2020 daemon.info dnsmasq[8765]: read /etc/hosts - 4 addresses
Wed Dec 30 04:16:43 2020 daemon.info dnsmasq[8765]: read /tmp/hosts/dhcp.cfg01411c - 0 addresses
+ logger end testing channel 13
Wed Dec 30 04:16:44 2020 user.notice root: end testing channel 13
+ kill '%1'
+ pkill -9 logread
+ set -x
+ uci show wireless
wireless.radio0=wifi-device
wireless.radio0.type='mac80211'
wireless.radio0.hwmode='11g'
wireless.radio0.path='platform/soc/3f300000.mmc/mmc_host/mmc1/mmc1:0001/mmc1:0001:1'
wireless.radio0.legacy_rates='0'
wireless.radio0.country='PL'
wireless.radio0.htmode='HT20'
wireless.radio0.channel='13'
wireless.default_radio0=wifi-iface
wireless.default_radio0.device='radio0'
wireless.default_radio0.network='lan'
wireless.default_radio0.mode='ap'
wireless.default_radio0.ssid='my_ssid'
wireless.default_radio0.wpa_disable_eapol_key_retries='1'
wireless.default_radio0.key='my_key'
wireless.default_radio0.hidden='1'
wireless.default_radio0.encryption='psk2'
+ uci set 'wireless.radio0.channel=12'
+ uci commit wireless
+ sleep 1
+ logread -f
+ logger start testing channel 12
Wed Dec 30 04:16:45 2020 user.notice root: start testing channel 12
+ wifi
+ sleep 3
Wed Dec 30 04:16:45 2020 daemon.notice netifd: radio0 (8783): command failed: No error information (-524)
Wed Dec 30 04:16:45 2020 user.notice mac80211: Failed command: iw dev wlan0 del
Wed Dec 30 04:16:45 2020 daemon.notice netifd: radio0 (8803): command failed: No error information (-524)
Wed Dec 30 04:16:45 2020 user.notice mac80211: Failed command: iw dev wlan0 del
Wed Dec 30 04:16:45 2020 user.notice mac80211: Failed command: iw phy phy0 set antenna 0xffffffff 0xffffffff
Wed Dec 30 04:16:45 2020 daemon.notice netifd: radio0 (8803): command failed: Not supported (-95)
Wed Dec 30 04:16:45 2020 user.notice mac80211: Failed command: iw phy phy0 set antenna_gain 0
Wed Dec 30 04:16:45 2020 daemon.notice netifd: radio0 (8803): command failed: I/O error (-5)
Wed Dec 30 04:16:45 2020 user.notice mac80211: Failed command: iw phy phy0 set distance 0
Wed Dec 30 04:16:45 2020 daemon.notice netifd: radio0 (8803): command failed: Too many open files in system (-23)
Wed Dec 30 04:16:45 2020 user.notice mac80211: Failed command: iw phy phy0 interface add wlan0 type __ap
Wed Dec 30 04:16:45 2020 daemon.err hostapd: Configuration file: /var/run/hostapd-phy0.conf
Wed Dec 30 04:16:45 2020 daemon.notice hostapd: wlan0: interface state UNINITIALIZED->COUNTRY_UPDATE
Wed Dec 30 04:16:45 2020 daemon.warn hostapd: wlan0: Could not connect to kernel driver
Wed Dec 30 04:16:45 2020 daemon.err hostapd: Using interface wlan0 with hwaddr MAC_ADDRESS_WAS_HERE and ssid "my_ssid"
Wed Dec 30 04:16:45 2020 kern.info kernel: [ 8813.087454] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
Wed Dec 30 04:16:45 2020 daemon.err hostapd: Failed to set beacon parameters
Wed Dec 30 04:16:45 2020 daemon.warn hostapd: wlan0: Could not connect to kernel driver
Wed Dec 30 04:16:45 2020 daemon.err hostapd: Interface initialization failed
Wed Dec 30 04:16:45 2020 daemon.notice hostapd: wlan0: interface state COUNTRY_UPDATE->DISABLED
Wed Dec 30 04:16:45 2020 daemon.notice hostapd: wlan0: AP-DISABLED
Wed Dec 30 04:16:45 2020 daemon.err hostapd: wlan0: Unable to setup interface.
Wed Dec 30 04:16:45 2020 daemon.notice hostapd: wlan0: interface state DISABLED->DISABLED
Wed Dec 30 04:16:45 2020 kern.err kernel: [ 8813.180327] ieee80211 phy0: brcmf_cfg80211_start_ap: Set Channel failed: chspec=4108, -52
Wed Dec 30 04:16:45 2020 daemon.notice hostapd: wlan0: AP-DISABLED
Wed Dec 30 04:16:45 2020 daemon.notice hostapd: wlan0: CTRL-EVENT-TERMINATING
Wed Dec 30 04:16:45 2020 daemon.err hostapd: hostapd_free_hapd_data: Interface wlan0 wasn't started
Wed Dec 30 04:16:45 2020 daemon.notice hostapd: nl80211: deinit ifname=wlan0 disabled_11b_rates=0
Wed Dec 30 04:16:46 2020 daemon.notice hostapd: ELOOP: remaining socket: sock=22 eloop_data=0x7fa178be60 user_data=0 handler=0x41d078
Wed Dec 30 04:16:46 2020 daemon.notice netifd: radio0 (8803): WARNING (wireless_add_process): executable path /usr/sbin/wpad does not match process 8118 path ()
Wed Dec 30 04:16:46 2020 daemon.notice netifd: radio0 (8803): Device setup failed: HOSTAPD_START_FAILED
+ logger end testing channel 12
Wed Dec 30 04:16:48 2020 user.notice root: end testing channel 12
+ kill '%1'
+ pkill -9 logread
+ set -x
+ uci show wireless
wireless.radio0=wifi-device
wireless.radio0.type='mac80211'
wireless.radio0.hwmode='11g'
wireless.radio0.path='platform/soc/3f300000.mmc/mmc_host/mmc1/mmc1:0001/mmc1:0001:1'
wireless.radio0.legacy_rates='0'
wireless.radio0.country='PL'
wireless.radio0.htmode='HT20'
wireless.radio0.channel='12'
wireless.default_radio0=wifi-iface
wireless.default_radio0.device='radio0'
wireless.default_radio0.network='lan'
wireless.default_radio0.mode='ap'
wireless.default_radio0.ssid='my_ssid'
wireless.default_radio0.wpa_disable_eapol_key_retries='1'
wireless.default_radio0.key='my_key'
wireless.default_radio0.hidden='1'
wireless.default_radio0.encryption='psk2'
+ uci set 'wireless.radio0.channel=auto'
+ uci commit wireless
+ sleep 1
+ logread -f
+ logger start testing channel auto
Wed Dec 30 04:16:49 2020 user.notice root: start testing channel auto
+ wifi
+ sleep 3
Wed Dec 30 04:16:49 2020 daemon.notice netifd: radio0 (8880): command failed: No error information (-524)
Wed Dec 30 04:16:49 2020 user.notice mac80211: Failed command: iw dev wlan0 del
Wed Dec 30 04:16:49 2020 daemon.notice netifd: radio0 (8900): command failed: No error information (-524)
Wed Dec 30 04:16:49 2020 user.notice mac80211: Failed command: iw dev wlan0 del
Wed Dec 30 04:16:49 2020 user.notice mac80211: Failed command: iw phy phy0 set antenna 0xffffffff 0xffffffff
Wed Dec 30 04:16:49 2020 daemon.notice netifd: radio0 (8900): command failed: Not supported (-95)
Wed Dec 30 04:16:49 2020 user.notice mac80211: Failed command: iw phy phy0 set antenna_gain 0
Wed Dec 30 04:16:49 2020 daemon.notice netifd: radio0 (8900): command failed: I/O error (-5)
Wed Dec 30 04:16:49 2020 user.notice mac80211: Failed command: iw phy phy0 set distance 0
Wed Dec 30 04:16:49 2020 daemon.notice netifd: radio0 (8900): command failed: Too many open files in system (-23)
Wed Dec 30 04:16:49 2020 user.notice mac80211: Failed command: iw phy phy0 interface add wlan0 type __ap
Wed Dec 30 04:16:49 2020 daemon.err hostapd: Configuration file: /var/run/hostapd-phy0.conf
Wed Dec 30 04:16:49 2020 daemon.notice hostapd: wlan0: interface state UNINITIALIZED->COUNTRY_UPDATE
Wed Dec 30 04:16:49 2020 daemon.notice hostapd: ACS: Automatic channel selection started, this may take a bit
Wed Dec 30 04:16:49 2020 kern.info kernel: [ 8817.154489] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
Wed Dec 30 04:16:49 2020 kern.err kernel: [ 8817.166683] ieee80211 phy0: brcmf_run_escan: error (-52)
Wed Dec 30 04:16:49 2020 kern.err kernel: [ 8817.173057] ieee80211 phy0: brcmf_cfg80211_scan: scan error (-52)
Wed Dec 30 04:16:49 2020 kern.err kernel: [ 8817.184908] ieee80211 phy0: brcmf_run_escan: error (-52)
Wed Dec 30 04:16:49 2020 kern.err kernel: [ 8817.191232] ieee80211 phy0: brcmf_cfg80211_scan: scan error (-52)
Wed Dec 30 04:16:49 2020 daemon.err hostapd: ACS: Failed to request initial scan
Wed Dec 30 04:16:49 2020 daemon.warn hostapd: wlan0: IEEE 802.11 Configured channel (0) not found from the channel list of current mode (1) IEEE 802.11g
Wed Dec 30 04:16:49 2020 daemon.warn hostapd: wlan0: IEEE 802.11 Hardware does not support configured channel
Wed Dec 30 04:16:49 2020 daemon.err hostapd: Could not select hw_mode and channel. (-3)
Wed Dec 30 04:16:49 2020 daemon.notice hostapd: wlan0: interface state COUNTRY_UPDATE->DISABLED
Wed Dec 30 04:16:49 2020 daemon.notice hostapd: wlan0: AP-DISABLED
Wed Dec 30 04:16:49 2020 daemon.err hostapd: wlan0: Unable to setup interface.
Wed Dec 30 04:16:49 2020 daemon.notice hostapd: wlan0: interface state DISABLED->DISABLED
Wed Dec 30 04:16:49 2020 daemon.notice hostapd: wlan0: AP-DISABLED
Wed Dec 30 04:16:49 2020 daemon.notice hostapd: wlan0: CTRL-EVENT-TERMINATING
Wed Dec 30 04:16:49 2020 daemon.err hostapd: hostapd_free_hapd_data: Interface wlan0 wasn't started
Wed Dec 30 04:16:49 2020 daemon.notice hostapd: nl80211: deinit ifname=wlan0 disabled_11b_rates=0
Wed Dec 30 04:16:50 2020 daemon.notice netifd: radio0 (8900): WARNING (wireless_add_process): executable path /usr/sbin/wpad does not match process 8118 path ()
Wed Dec 30 04:16:50 2020 daemon.notice netifd: radio0 (8900): Device setup failed: HOSTAPD_START_FAILED
+ logger end testing channel auto
Wed Dec 30 04:16:52 2020 user.notice root: end testing channel auto
+ kill '%1'
+ pkill -9 logread
+ set -x
+ uci show wireless
wireless.radio0=wifi-device
wireless.radio0.type='mac80211'
wireless.radio0.hwmode='11g'
wireless.radio0.path='platform/soc/3f300000.mmc/mmc_host/mmc1/mmc1:0001/mmc1:0001:1'
wireless.radio0.legacy_rates='0'
wireless.radio0.country='PL'
wireless.radio0.htmode='HT20'
wireless.radio0.channel='auto'
wireless.default_radio0=wifi-iface
wireless.default_radio0.device='radio0'
wireless.default_radio0.network='lan'
wireless.default_radio0.mode='ap'
wireless.default_radio0.ssid='my_ssid'
wireless.default_radio0.wpa_disable_eapol_key_retries='1'
wireless.default_radio0.key='my_key'
wireless.default_radio0.hidden='1'
wireless.default_radio0.encryption='psk2'
+ uci set 'wireless.radio0.channel=11'
+ uci commit wireless
+ sleep 1
+ logread -f
+ logger start testing channel 11
Wed Dec 30 04:16:53 2020 user.notice root: start testing channel 11
+ wifi
+ sleep 3
Wed Dec 30 04:16:53 2020 daemon.notice netifd: radio0 (8970): command failed: No error information (-524)
Wed Dec 30 04:16:53 2020 user.notice mac80211: Failed command: iw dev wlan0 del
Wed Dec 30 04:16:53 2020 daemon.notice netifd: radio0 (8990): command failed: No error information (-524)
Wed Dec 30 04:16:53 2020 user.notice mac80211: Failed command: iw dev wlan0 del
Wed Dec 30 04:16:53 2020 user.notice mac80211: Failed command: iw phy phy0 set antenna 0xffffffff 0xffffffff
Wed Dec 30 04:16:53 2020 daemon.notice netifd: radio0 (8990): command failed: Not supported (-95)
Wed Dec 30 04:16:53 2020 user.notice mac80211: Failed command: iw phy phy0 set antenna_gain 0
Wed Dec 30 04:16:53 2020 daemon.notice netifd: radio0 (8990): command failed: I/O error (-5)
Wed Dec 30 04:16:53 2020 user.notice mac80211: Failed command: iw phy phy0 set distance 0
Wed Dec 30 04:16:53 2020 daemon.notice netifd: radio0 (8990): command failed: Too many open files in system (-23)
Wed Dec 30 04:16:53 2020 user.notice mac80211: Failed command: iw phy phy0 interface add wlan0 type __ap
Wed Dec 30 04:16:53 2020 daemon.err hostapd: Configuration file: /var/run/hostapd-phy0.conf
Wed Dec 30 04:16:53 2020 daemon.notice hostapd: wlan0: interface state UNINITIALIZED->COUNTRY_UPDATE
Wed Dec 30 04:16:53 2020 daemon.warn hostapd: wlan0: Could not connect to kernel driver
Wed Dec 30 04:16:53 2020 daemon.err hostapd: Using interface wlan0 with hwaddr MAC_ADDRESS_WAS_HERE and ssid "my_ssid"
Wed Dec 30 04:16:53 2020 kern.info kernel: [ 8821.268054] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
Wed Dec 30 04:16:53 2020 kern.info kernel: [ 8821.429792] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
Wed Dec 30 04:16:53 2020 daemon.notice hostapd: wlan0: interface state COUNTRY_UPDATE->ENABLED
Wed Dec 30 04:16:53 2020 daemon.notice hostapd: wlan0: AP-ENABLED
Wed Dec 30 04:16:53 2020 daemon.notice netifd: Network device 'wlan0' link is up
Wed Dec 30 04:16:53 2020 daemon.notice netifd: Interface 'lan' is enabled
Wed Dec 30 04:16:53 2020 daemon.notice netifd: Interface 'lan' is setting up now
Wed Dec 30 04:16:53 2020 daemon.notice netifd: Interface 'lan' is now up
Wed Dec 30 04:16:53 2020 daemon.notice netifd: Interface 'lan' has link connectivity
Wed Dec 30 04:16:54 2020 user.notice firewall: Reloading firewall due to ifup of lan (wlan0)
Wed Dec 30 04:16:55 2020 daemon.info dnsmasq[8765]: exiting on receipt of SIGTERM
Wed Dec 30 04:16:55 2020 daemon.info dnsmasq[9156]: started, version 2.80 cachesize 150
Wed Dec 30 04:16:55 2020 daemon.info dnsmasq[9156]: DNS service limited to local subnets
Wed Dec 30 04:16:55 2020 daemon.info dnsmasq[9156]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth no-DNSSEC no-ID loop-detect inotify dumpfile
Wed Dec 30 04:16:55 2020 daemon.info dnsmasq-dhcp[9156]: DHCP, IP range IP_ADDRESS_WAS_HERE -- IP_ADDRESS_WAS_HERE, lease time 12h
Wed Dec 30 04:16:55 2020 daemon.info dnsmasq[9156]: using local addresses only for domain test
Wed Dec 30 04:16:55 2020 daemon.info dnsmasq[9156]: using local addresses only for domain onion
Wed Dec 30 04:16:55 2020 daemon.info dnsmasq[9156]: using local addresses only for domain localhost
Wed Dec 30 04:16:55 2020 daemon.info dnsmasq[9156]: using local addresses only for domain local
Wed Dec 30 04:16:55 2020 daemon.info dnsmasq[9156]: using local addresses only for domain invalid
Wed Dec 30 04:16:55 2020 daemon.info dnsmasq[9156]: using local addresses only for domain bind
Wed Dec 30 04:16:55 2020 daemon.info dnsmasq[9156]: using local addresses only for domain lan
Wed Dec 30 04:16:55 2020 daemon.info dnsmasq[9156]: reading /tmp/resolv.conf.auto
Wed Dec 30 04:16:55 2020 daemon.info dnsmasq[9156]: using local addresses only for domain test
Wed Dec 30 04:16:55 2020 daemon.info dnsmasq[9156]: using local addresses only for domain onion
Wed Dec 30 04:16:55 2020 daemon.info dnsmasq[9156]: using local addresses only for domain localhost
Wed Dec 30 04:16:55 2020 daemon.info dnsmasq[9156]: using local addresses only for domain local
Wed Dec 30 04:16:55 2020 daemon.info dnsmasq[9156]: using local addresses only for domain invalid
Wed Dec 30 04:16:55 2020 daemon.info dnsmasq[9156]: using local addresses only for domain bind
Wed Dec 30 04:16:55 2020 daemon.info dnsmasq[9156]: using local addresses only for domain lan
Wed Dec 30 04:16:55 2020 daemon.info dnsmasq[9156]: using nameserver IP_ADDRESS_WAS_HERE#53
Wed Dec 30 04:16:55 2020 daemon.info dnsmasq[9156]: using nameserver IP_ADDRESS_WAS_HERE#53
Wed Dec 30 04:16:55 2020 daemon.info dnsmasq[9156]: read /etc/hosts - 4 addresses
Wed Dec 30 04:16:55 2020 daemon.info dnsmasq[9156]: read /tmp/hosts/dhcp.cfg01411c - 2 addresses
Wed Dec 30 04:16:55 2020 daemon.info dnsmasq-dhcp[9156]: read /etc/ethers - 0 addresses
+ logger end testing channel 11
Wed Dec 30 04:16:56 2020 user.notice root: end testing channel 11
+ kill '%1'
+ pkill -9 logread
+ iw list
Wiphy phy0
        max # scan SSIDs: 10
        max scan IEs length: 2048 bytes
        max # sched scan SSIDs: 0
        max # match sets: 0
        max # scan plans: 1
        max scan plan interval: -1
        max scan plan iterations: 0
        Retry short limit: 7
        Retry long limit: 4
        Coverage class: 0 (up to 0m)
        Available Antennas: TX 0 RX 0
        Supported interface modes:
                 * IBSS
                 * managed
                 * AP
                 * P2P-client
                 * P2P-GO
                 * P2P-device
        Band 1:
                Capabilities: 0x1020
                        HT20
                        Static SM Power Save
                        RX HT20 SGI
                        No RX STBC
                        Max AMSDU length: 3839 bytes
                        DSSS/CCK HT40
                Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
                Minimum RX AMPDU time spacing: 16 usec (0x07)
                HT TX/RX MCS rate indexes supported: 0-7
                Frequencies:
                        * 2412 MHz [1] (20.0 dBm)
                        * 2417 MHz [2] (20.0 dBm)
                        * 2422 MHz [3] (20.0 dBm)
                        * 2427 MHz [4] (20.0 dBm)
                        * 2432 MHz [5] (20.0 dBm)
                        * 2437 MHz [6] (20.0 dBm)
                        * 2442 MHz [7] (20.0 dBm)
                        * 2447 MHz [8] (20.0 dBm)
                        * 2452 MHz [9] (20.0 dBm)
                        * 2457 MHz [10] (20.0 dBm)
                        * 2462 MHz [11] (20.0 dBm)
                        * 2467 MHz [12] (20.0 dBm)
                        * 2472 MHz [13] (20.0 dBm)
                        * 2484 MHz [14] (disabled)
        valid interface combinations:
                 * #{ managed } <= 1, #{ P2P-device } <= 1, #{ P2P-client, P2P-GO } <= 1,
                   total <= 3, #channels <= 2
                 * #{ managed } <= 1, #{ AP } <= 1, #{ P2P-client } <= 1, #{ P2P-device } <= 1,
                   total <= 4, #channels <= 1
        Supported extended features:
                * [ 4WAY_HANDSHAKE_STA_PSK ]: 4-way handshake with PSK in station mode
                * [ 4WAY_HANDSHAKE_STA_1X ]: 4-way handshake with 802.1X in station mode
+ iwlist wlan0 channel
wlan0     13 channels in total; available frequencies :
          Channel 01 : 2.412 GHz
          Channel 02 : 2.417 GHz
          Channel 03 : 2.422 GHz
          Channel 04 : 2.427 GHz
          Channel 05 : 2.432 GHz
          Channel 06 : 2.437 GHz
          Channel 07 : 2.442 GHz
          Channel 08 : 2.447 GHz
          Channel 09 : 2.452 GHz
          Channel 10 : 2.457 GHz
          Channel 11 : 2.462 GHz
          Channel 12 : 2.467 GHz
          Channel 13 : 2.472 GHz
12.01.20213572Base systemBug ReportVery LowHighath79: ar934x internal switch port 5 missingAllUnconfirmed Task Description

Applies to all versions including master branch,
but only in ath79 target
old ar71xx target does not have the problem

for the internal built-in switch for ar934x series
port 5 of the switch is missing, and therefore physical ports
that are connected to port 5 of the internal switch instead of GMAC0
cannot be used.

Attempting to set a VLAN that includes port 5 never takes effect.

This issue is not noticed for many other ar934x boards with 5 physical ports
because routers with 4 LAN and 1 WAN port use GMAC0 for the WAN port
instead of port 5 of the internal switch.

in ar71xx the driver is
target/linux/ar71xx/files/drivers/net/ethernet/atheros/ag71xx/ag71xx_ar7240.c

in ath79 the new driver is
target/linux/generic/files/drivers/net/phy/ar8216.c

for 2 of my AR9341 boards
EAP300 v2 and ENS202EXT
port 5 is missing from swconfig output

ath79 output:

root@OpenWrt:~# swconfig dev switch0 show
Global attributes:
        enable_vlan: 1
        ar8xxx_mib_poll_interval: 500
        ar8xxx_mib_type: 0
        enable_mirror_rx: 0
        enable_mirror_tx: 0
        mirror_monitor_port: 0
        mirror_source_port: 0
        arl_table: address resolution table
Port 0: MAC 88:dc:96:34:64:d4
Port 1: MAC 00:e1:18:b0:01:1f

Port 0:
        mib: MIB counters
RxGoodByte  : 810502 (791.5 KiB)
TxByte      : 505477 (493.6 KiB)

        pvid: 0
        link: port:0 link:up speed:1000baseT full-duplex txflow rxflow
Port 1:
        mib: MIB counters
RxGoodByte  : 493285 (481.7 KiB)
TxByte      : 802608 (783.7 KiB)

        pvid: 1
        link: port:1 link:up speed:100baseT full-duplex auto
Port 2:
        mib: No MIB data
        pvid: 0
        link: port:2 link:down
Port 3:
        mib: No MIB data
        pvid: 0
        link: port:3 link:down
Port 4:
        mib: No MIB data
        pvid: 0
        link: port:4 link:down
VLAN 1:
        vid: 1
        ports: 0t 1

ar71xx output:

root@OpenWrt:/# swconfig dev switch0 show
Global attributes:
        enable_vlan: 1
        mirror_monitor_port: 15
Port 0:
        enable_mirror_rx: 0
        enable_mirror_tx: 0
        pvid: 0
        link: port:0 link:up speed:1000baseT full-duplex txflow rxflow
Port 1:
        enable_mirror_rx: 0
        enable_mirror_tx: 0
        pvid: 2
        link: port:1 link:down
Port 2:
        enable_mirror_rx: 0
        enable_mirror_tx: 0
        pvid: 1
        link: port:2 link:down
Port 3:
        enable_mirror_rx: 0
        enable_mirror_tx: 0
        pvid: 1
        link: port:3 link:down
Port 4:
        enable_mirror_rx: 0
        enable_mirror_tx: 0
        pvid: 1
        link: port:4 link:down
Port 5:
        enable_mirror_rx: 0
        enable_mirror_tx: 0
        pvid: 1
        link: port:5 link:down
VLAN 0:
        vid: 0
        ports: 0t
VLAN 1:
        vid: 1
        ports: 0t 2 3 4 5
VLAN 2:
        vid: 2
        ports: 0t 1

asking for port 5 specifically returns ???

root@OpenWrt:/# swconfig dev switch0 port 5 show
Port 5:
        mib: ???
        pvid: ???
        link: ???
20.01.20213582Base systemBug ReportVery LowHighbad eraseblock causes unreadable factory partition on N...TrunkUnconfirmed Task Description

- Device problem occurs on

Netgear R6800

- Software version of OpenWrt

current snapshot

dmesg of the affected device:

[    0.000000] Linux version 5.4.89 (builder@buildhost) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r15541-e87c0d934c)) #0 SMP Tue Jan 19 12:01:03 2021
[    0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[    0.000000] printk: bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[    0.000000] MIPS: machine is Netgear R6800
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] VPE topology {2,2} total 4
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x000000000fffffff]
[    0.000000]   HighMem  empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x000000000fffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff]
[    0.000000] On node 0 totalpages: 65536
[    0.000000]   Normal zone: 576 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 65536 pages, LIFO batch:15
[    0.000000] percpu: Embedded 14 pages/cpu s26768 r8192 d22384 u57344
[    0.000000] pcpu-alloc: s26768 r8192 d22384 u57344 alloc=14*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 64960
[    0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[    0.000000] Writing ErrCtl register=00011190
[    0.000000] Readback ErrCtl register=00011190
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 250272K/262144K available (6060K kernel code, 204K rwdata, 1288K rodata, 1268K init, 238K bss, 11872K reserved, 0K cma-reserved, 0K highmem)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[    0.000000] NR_IRQS: 256
[    0.000000] random: get_random_bytes called from start_kernel+0x340/0x558 with crng_init=0
[    0.000000] CPU Clock: 880MHz
[    0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns
[    0.000008] sched_clock: 32 bits at 440MHz, resolution 2ns, wraps every 4880645118ns
[    0.015488] Calibrating delay loop... 583.68 BogoMIPS (lpj=1167360)
[    0.055815] pid_max: default: 32768 minimum: 301
[    0.065164] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.079568] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.097530] rcu: Hierarchical SRCU implementation.
[    0.107607] smp: Bringing up secondary CPUs ...
[    0.133505] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.133516] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.133528] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    0.133626] CPU1 revision is: 0001992f (MIPS 1004Kc)
[    0.144747] Synchronize counters for CPU 1: done.
[    0.224318] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.224327] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.224335] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    0.224392] CPU2 revision is: 0001992f (MIPS 1004Kc)
[    0.243222] Synchronize counters for CPU 2: done.
[    0.319738] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.319746] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.319754] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    0.319814] CPU3 revision is: 0001992f (MIPS 1004Kc)
[    0.330823] Synchronize counters for CPU 3: done.
[    0.390434] smp: Brought up 1 node, 4 CPUs
[    0.403083] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.422382] futex hash table entries: 1024 (order: 3, 32768 bytes, linear)
[    0.436204] pinctrl core: initialized pinctrl subsystem
[    0.448120] NET: Registered protocol family 16
[    0.467941] FPU Affinity set after 4688 emulations
[    0.484349] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512
[    0.505771] clocksource: Switched to clocksource GIC
[    0.517235] random: fast init done
[    0.519932] NET: Registered protocol family 2
[    0.533512] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[    0.550071] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear)
[    0.565232] TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear)
[    0.579410] TCP: Hash tables configured (established 2048 bind 2048)
[    0.592145] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.605030] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.619125] NET: Registered protocol family 1
[    0.627683] PCI: CLS 0 bytes, default 32
[    0.725705] 4 CPUs re-calibrate udelay(lpj = 1163264)
[    0.737308] workingset: timestamp_bits=14 max_order=16 bucket_order=2
[    0.762216] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.773732] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.794941] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[    0.811403] mt7621_gpio 1e000600.gpio: registering 32 gpios
[    0.822747] mt7621_gpio 1e000600.gpio: registering 32 gpios
[    0.834003] mt7621_gpio 1e000600.gpio: registering 32 gpios
[    0.845943] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.862253] printk: console [ttyS0] disabled
[    0.870712] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A
[    0.888650] printk: console [ttyS0] enabled
[    0.905190] printk: bootconsole [early0] disabled
[    0.926457] mt7621-nand 1e003000.nand: Using programmed access timing: 31c07388
[    0.941280] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xf1
[    0.953951] nand: Macronix MX30LF1G18AC
[    0.961590] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    0.976676] mt7621-nand 1e003000.nand: ECC strength adjusted to 4 bits
[    0.989741] mt7621-nand 1e003000.nand: Using programmed access timing: 21005134
[    1.004308] mt7621-nand 1e003000.nand: Using programmed access timing: 21005134
[    1.018871] Scanning device for bad blocks
[    1.354795] Bad eraseblock 258 at 0x000002040000
[    2.333921] 7 fixed-partitions partitions found on MTD device mt7621-nand
[    2.347453] Creating 7 MTD partitions on "mt7621-nand":
[    2.357876] 0x000000000000-0x000000100000 : "u-boot"
[    2.369215] 0x000000100000-0x000000200000 : "SC PART_MAP"
[    2.381223] 0x000000200000-0x000000600000 : "kernel"
[    2.392538] 0x000000600000-0x000002e00000 : "ubi"
[    2.403387] 0x000002e00000-0x000004600000 : "reserved0"
[    2.415314] 0x000004600000-0x000004800000 : "factory"
[    2.426712] 0x000004800000-0x000008000000 : "reserved1"
[    2.440236] libphy: Fixed MDIO Bus: probed
[    2.476139] libphy: mdio: probed
[    2.482841] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
[    2.498374] mtk_soc_eth 1e100000.ethernet: generated random MAC address fa:25:cd:89:6b:20
[    2.515564] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 21
[    2.533374] i2c-mt7621 1e000900.i2c: clock 100 kHz
[    2.544345] mt7621-pci 1e140000.pcie: Parsing DT failed
[    2.557366] NET: Registered protocol family 10
[    2.567638] Segment Routing with IPv6
[    2.575077] NET: Registered protocol family 17
[    2.584024] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    2.610098] 8021q: 802.1Q VLAN Support v1.8
[    2.620267] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
[    2.645577] libphy: dsa slave smi: probed
[    2.654066] mt7530 mdio-bus:1f lan4 (uninitialized): PHY [dsa-0.0:00] driver [Generic PHY]
[    2.671990] mt7530 mdio-bus:1f lan3 (uninitialized): PHY [dsa-0.0:01] driver [Generic PHY]
[    2.690018] mt7530 mdio-bus:1f lan2 (uninitialized): PHY [dsa-0.0:02] driver [Generic PHY]
[    2.707897] mt7530 mdio-bus:1f lan1 (uninitialized): PHY [dsa-0.0:03] driver [Generic PHY]
[    2.725954] mt7530 mdio-bus:1f wan (uninitialized): PHY [dsa-0.0:04] driver [Generic PHY]
[    2.743767] mt7530 mdio-bus:1f: configuring for fixed/rgmii link mode
[    2.761395] DSA: tree 0 setup
[    2.767651] rt2880-pinmux pinctrl: pcie is already enabled
[    2.778618] mt7621-pci 1e140000.pcie: Error applying setting, reverse things back
[    2.793671] mt7621-pci-phy 1e149000.pcie-phy: PHY for 0xbe149000 (dual port = 1)
[    2.808637] mt7621-pci-phy 1e14a000.pcie-phy: PHY for 0xbe14a000 (dual port = 0)
[    2.923192] mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz
[    2.934315] mt7621-pci-phy 1e14a000.pcie-phy: Xtal is 40MHz
[    3.045148] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK)
[    3.059026] mt7621-pci 1e140000.pcie: PCIE0 enabled
[    3.068744] mt7621-pci 1e140000.pcie: PCIE1 enabled
[    3.078473] mt7621-pci 1e140000.pcie: PCI coherence region base: 0x60000000, mask/settings: 0xf0000002
[    3.097178] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00
[    3.109861] pci_bus 0000:00: root bus resource [io  0x1e160000-0x1e16ffff]
[    3.123561] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[    3.137262] pci_bus 0000:00: root bus resource [bus 00-ff]
[    3.148239] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400
[    3.160249] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[    3.172743] pci 0000:00:00.0: reg 0x14: [mem 0x60400000-0x6040ffff]
[    3.185301] pci 0000:00:00.0: supports D1
[    3.193293] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[    3.205112] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400
[    3.217129] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[    3.229624] pci 0000:00:01.0: reg 0x14: [mem 0x60410000-0x6041ffff]
[    3.242183] pci 0000:00:01.0: supports D1
[    3.250175] pci 0000:00:01.0: PME# supported from D0 D1 D3hot
[    3.263178] pci 0000:01:00.0: [14c3:7615] type 00 class 0x000280
[    3.275220] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit]
[    3.288923] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5 GT/s x1 link)
[    3.317844] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[    3.328268] pci 0000:00:00.0:   bridge window [io  0x0000-0x0fff]
[    3.340414] pci 0000:00:00.0:   bridge window [mem 0x60000000-0x600fffff]
[    3.353947] pci 0000:00:00.0:   bridge window [mem 0x60100000-0x601fffff pref]
[    3.368342] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[    3.381778] pci 0000:02:00.0: [14c3:7615] type 00 class 0x000280
[    3.393804] pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit]
[    3.407503] pci 0000:02:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0000:00:01.0 (capable of 4.000 Gb/s with 5 GT/s x1 link)
[    3.436377] pci 0000:00:01.0: PCI bridge to [bus 02-ff]
[    3.446812] pci 0000:00:01.0:   bridge window [io  0x0000-0x0fff]
[    3.458957] pci 0000:00:01.0:   bridge window [mem 0x60200000-0x602fffff]
[    3.472485] pci 0000:00:01.0:   bridge window [mem 0x60300000-0x603fffff pref]
[    3.486883] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[    3.500109] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[    3.513290] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[    3.527169] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000]
[    3.540349] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000]
[    3.554228] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[    3.567766] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x601fffff pref]
[    3.582164] pci 0000:00:01.0: BAR 8: assigned [mem 0x60200000-0x602fffff]
[    3.595696] pci 0000:00:01.0: BAR 9: assigned [mem 0x60300000-0x603fffff pref]
[    3.610094] pci 0000:00:00.0: BAR 1: assigned [mem 0x60400000-0x6040ffff]
[    3.623628] pci 0000:00:01.0: BAR 1: assigned [mem 0x60410000-0x6041ffff]
[    3.637159] pci 0000:00:00.0: BAR 7: assigned [io  0x1e160000-0x1e160fff]
[    3.650693] pci 0000:00:01.0: BAR 7: assigned [io  0x1e161000-0x1e161fff]
[    3.664233] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit]
[    3.678813] pci 0000:00:00.0: PCI bridge to [bus 01]
[    3.688707] pci 0000:00:00.0:   bridge window [io  0x1e160000-0x1e160fff]
[    3.702245] pci 0000:00:00.0:   bridge window [mem 0x60000000-0x600fffff]
[    3.715774] pci 0000:00:00.0:   bridge window [mem 0x60100000-0x601fffff pref]
[    3.730177] pci 0000:02:00.0: BAR 0: assigned [mem 0x60200000-0x602fffff 64bit]
[    3.744750] pci 0000:00:01.0: PCI bridge to [bus 02]
[    3.754648] pci 0000:00:01.0:   bridge window [io  0x1e161000-0x1e161fff]
[    3.768175] pci 0000:00:01.0:   bridge window [mem 0x60200000-0x602fffff]
[    3.781719] pci 0000:00:01.0:   bridge window [mem 0x60300000-0x603fffff pref]
[    3.796709] mt7530 mdio-bus:1f: Link is Up - 1Gbps/Full - flow control off
[    3.797818] UBI: auto-attach mtd3
[    3.817037] ubi0: attaching mtd3
[    4.228815] ubi0: scanning is finished
[    4.252554] ubi0: attached mtd3 (name "ubi", size 40 MiB)
[    4.263330] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    4.277018] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    4.290537] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[    4.304401] ubi0: good PEBs: 319, bad PEBs: 1, corrupted PEBs: 0
[    4.316361] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[    4.330744] ubi0: max/mean erase counter: 3/1, WL threshold: 4096, image sequence number: 1610490449
[    4.348928] ubi0: available PEBs: 0, total reserved PEBs: 319, PEBs reserved for bad PEB handling: 19
[    4.367314] ubi0: background thread "ubi_bgt0d" started, PID 486
[    4.369678] block ubiblock0_0: created from ubi0:0(rootfs)
[    4.390224] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[    4.404092] hctosys: unable to open rtc device (rtc0)
[    4.420757] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[    4.439415] Freeing unused kernel memory: 1268K
[    4.448460] This architecture does not have kernel memory protection.
[    4.461282] Run /sbin/init as init process
[    5.015980] init: Console is alive
[    5.023014] init: - watchdog -
[    5.788477] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    5.889330] usbcore: registered new interface driver usbfs
[    5.900381] usbcore: registered new interface driver hub
[    5.911069] usbcore: registered new device driver usb
[    5.930998] xhci-mtk 1e1c0000.xhci: 1e1c0000.xhci supply vbus not found, using dummy regulator
[    5.948312] xhci-mtk 1e1c0000.xhci: 1e1c0000.xhci supply vusb33 not found, using dummy regulator
[    5.966019] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
[    5.976632] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 1
[    5.997854] xhci-mtk 1e1c0000.xhci: hcc params 0x01401198 hci version 0x96 quirks 0x0000000000210010
[    6.016150] xhci-mtk 1e1c0000.xhci: irq 20, io mem 0x1e1c0000
[    6.028879] hub 1-0:1.0: USB hub found
[    6.036452] hub 1-0:1.0: 2 ports detected
[    6.045096] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
[    6.055717] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 2
[    6.070642] xhci-mtk 1e1c0000.xhci: Host supports USB 3.0 SuperSpeed
[    6.083508] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[    6.100520] hub 2-0:1.0: USB hub found
[    6.108083] hub 2-0:1.0: 1 port detected
[    6.120758] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    6.146084] init: - preinit -
[    6.801631] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
[    6.817788] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[    6.834653] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[    7.012235] random: jshn: uninitialized urandom read (4 bytes read)
[    7.081996] random: jshn: uninitialized urandom read (4 bytes read)
[    7.148308] random: jshn: uninitialized urandom read (4 bytes read)
[    7.459020] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode
[    7.472618] 8021q: adding VLAN 0 to HW filter on device lan1
[   10.538231] mt7530 mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control rx/tx
[   10.553186] IPv6: ADDRCONF(NETDEV_CHANGE): lan1: link becomes ready
[   11.662660] UBIFS (ubi0:1): Mounting in unauthenticated mode
[   11.674294] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 616
[   11.716258] urandom_read: 6 callbacks suppressed
[   11.716270] random: procd: uninitialized urandom read (4 bytes read)
[   11.757609] UBIFS (ubi0:1): recovery needed
[   11.949230] UBIFS (ubi0:1): recovery completed
[   11.958261] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[   11.973860] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[   11.993611] UBIFS (ubi0:1): FS size: 32759808 bytes (31 MiB, 258 LEBs), journal size 1650688 bytes (1 MiB, 13 LEBs)
[   12.014396] UBIFS (ubi0:1): reserved for root: 1547326 bytes (1511 KiB)
[   12.027574] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID 354D5F9F-B560-4EBC-B79F-1976C57BD526, small LPT model
[   12.065167] mount_root: switching to ubifs overlay
[   12.093230] urandom-seed: Seeding with /etc/urandom.seed
[   12.203684] mt7530 mdio-bus:1f lan1: Link is Down
[   12.231835] procd: - early -
[   12.237737] procd: - watchdog -
[   12.845910] procd: - watchdog -
[   12.856805] procd: - ubus -
[   12.922792] procd: - init -
[   13.697474] urngd: v1.0.2 started.
[   13.746355] kmodloader: loading kernel modules from /etc/modules.d/*
[   13.843832] random: crng init done
[   14.012758] Key type cifs.idmap registered
[   14.180204] Loading modules backported from Linux version v5.8.18-0-gab435ce49bd1
[   14.195181] Backport generated by backports.git v5.8.18-1-0-ga630fd46
[   14.254645] xt_time: kernel timezone is -0000
[   14.320718] mt7621-pci 1e140000.pcie: bus=1 slot=0 irq=23
[   14.331525] pci 0000:00:00.0: enabling device (0006 -> 0007)
[   14.342810] mt7615e 0000:01:00.0: enabling device (0000 -> 0002)
[   14.362949] mt7615e 0000:01:00.0: Invalid MAC address, using random address 02:0f:65:aa:94:7b
[   14.385122] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   14.389324] mt7621-pci 1e140000.pcie: bus=2 slot=1 irq=24
[   14.400208] pci 0000:00:01.0: enabling device (0006 -> 0007)
[   14.411687] mt7615e 0000:02:00.0: enabling device (0000 -> 0002)
[   14.438077] mt7615e 0000:02:00.0: Invalid MAC address, using random address 22:3b:71:93:43:43
[   14.470145] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[   14.507102] PPP generic driver version 2.4.2
[   14.517369] NET: Registered protocol family 24
[   14.527918] mt7615e 0000:01:00.0: HW/SW Version: 0x8a108a10, Build Time: 20180518100604a
[   14.527918] 
[   14.539280] mt7615e 0000:02:00.0: HW/SW Version: 0x8a108a10, Build Time: 20180518100604a
[   14.539280] 
[   14.606704] kmodloader: done loading kernel modules from /etc/modules.d/*
[   14.852492] mt7615e 0000:01:00.0: N9 Firmware Version: _reserved_, Build Time: 20200814163649
[   14.869935] mt7615e 0000:02:00.0: N9 Firmware Version: _reserved_, Build Time: 20200814163649
[   14.935755] mt7615e 0000:01:00.0: CR4 Firmware Version: _reserved_, Build Time: 20190121161307
[   14.936807] mt7615e 0000:02:00.0: CR4 Firmware Version: _reserved_, Build Time: 20190121161307
[   21.063778] mtk_soc_eth 1e100000.ethernet eth0: Link is Down
[   21.076662] mtk_soc_eth 1e100000.ethernet: PPE table busy
[   21.100322] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
[   21.116356] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[   21.124458] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode
[   21.147789] 8021q: adding VLAN 0 to HW filter on device lan1
[   21.163286] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   21.177053] br-lan: port 1(lan1) entered blocking state
[   21.187810] br-lan: port 1(lan1) entered disabled state
[   21.200543] device lan1 entered promiscuous mode
[   21.209932] device eth0 entered promiscuous mode
[   21.254001] mt7530 mdio-bus:1f lan2: configuring for phy/gmii link mode
[   21.268901] 8021q: adding VLAN 0 to HW filter on device lan2
[   21.286171] br-lan: port 2(lan2) entered blocking state
[   21.296704] br-lan: port 2(lan2) entered disabled state
[   21.308856] device lan2 entered promiscuous mode
[   21.327955] mt7530 mdio-bus:1f lan3: configuring for phy/gmii link mode
[   21.345826] 8021q: adding VLAN 0 to HW filter on device lan3
[   21.362764] br-lan: port 3(lan3) entered blocking state
[   21.373269] br-lan: port 3(lan3) entered disabled state
[   21.385022] device lan3 entered promiscuous mode
[   21.405777] mt7530 mdio-bus:1f lan4: configuring for phy/gmii link mode
[   21.420558] 8021q: adding VLAN 0 to HW filter on device lan4
[   21.435572] br-lan: port 4(lan4) entered blocking state
[   21.446096] br-lan: port 4(lan4) entered disabled state
[   21.459275] device lan4 entered promiscuous mode
[   21.488788] mt7530 mdio-bus:1f wan: configuring for phy/gmii link mode
[   21.502867] 8021q: adding VLAN 0 to HW filter on device wan
[   24.234221] mt7530 mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control rx/tx
[   24.249195] br-lan: port 1(lan1) entered blocking state
[   24.259657] br-lan: port 1(lan1) entered listening state
[   26.313720] br-lan: port 1(lan1) entered learning state
[   28.329713] br-lan: port 1(lan1) entered forwarding state
[   28.341012] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready

The dmesg shows a bad eraseblock 258 at 0×000002040000, this results in an unreadably factory partition. Symptoms: unreadable MAC addresses (as shown in the dmesg) and TX power on the radios limited to 6dBm, probably because of unreadable calibration data.

A hexdump of the factory partition shows correct contents, but shifted by 0×20000 bytes.

01.02.20213604Base systemBug ReportVery LowHighath9k firmware is 0 bytes on Fritzbox 7430TrunkUnconfirmed Task Description

Supply the following if possible:
- Device problem occurs on Fritz!box 7430
- Software versions of OpenWrt/LEDE snapshot r15642+2-eb11cd9ea3
- Steps to reproduce

Firmware for wifi ath9k in the directory /lib/firmware/ is 0 bytes.

Changing the parameter -s 0x1e000 to -s 0x1e800 results in the firmware
being created with 4096 bytes.

The ssid is now displayed, but wifi is very unstable and the connection
is quickly lost.

Here, too, the parameter -l 4096 was changed to -l 5120, which means
that the connection remains stable.

The file /etc/hotplug.d/firmware/12-ath9k-eeprom was locally changed to:

/usr/bin/fritz_cal_extract -i 1 -s 0x1e800 -e 0x207 -l 5120 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader")

Attached the completely changed file 12-ath9k-eeprom.

10.02.20213616Base systemBug ReportVery LowHighLAN peers unreachable after a few hoursTrunkUnconfirmed Task Description

Device: D-Link DIR-882 A1
Version: OpenWrt SNAPSHOT r15710-f5f01bcacd / LuCI Master git-21.029.67968-af1f961

After the router has been booted up for about a day, all LAN peers will become unreachable, but WAN works fine, resulting all LAN applications fail.

I ran a few tests. The Router was 192.168.1.1, a computer assigned 192.168.1.233 and another device 192.168.1.169.

Connection to the router was fine:

> tracert 192.168.1.1
Tracing route to OPENWRT.lan [192.168.1.1]
over a maximum of 30 hops:
  1     2 ms     2 ms     2 ms  OPENWRT.lan [192.168.1.1]
Trace complete.

Connection to itself was fine:

> tracert 192.168.1.233
Tracing route to WINDOWS.lan [192.168.1.233]
over a maximum of 30 hops:
  1    <1 ms    <1 ms    <1 ms  WINDOWS.lan [192.168.1.233]
Trace complete.

Connection to peer failed. It returned the address of itself:

> tracert 192.168.1.169
Tracing route to ANDROID.lan [192.168.1.169]
over a maximum of 30 hops:
  1  WINDOWS.lan [192.168.1.233]  reports: Destination host unreachable.
Trace complete.
> ping 192.168.1.169
Pinging 192.168.1.169 with 32 bytes of data:
Reply from 192.168.1.233: Destination host unreachable.
Reply from 192.168.1.233: Destination host unreachable.
Reply from 192.168.1.233: Destination host unreachable.
Reply from 192.168.1.233: Destination host unreachable.
Ping statistics for 192.168.1.169:
    Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),

System reboot can solve the problem temporarily. All LAN applications back online:

> ping 192.168.1.169
Pinging 192.168.1.169 with 32 bytes of data:
Reply from 192.168.1.169: bytes=32 time=4ms TTL=64
Reply from 192.168.1.169: bytes=32 time=5ms TTL=64
Reply from 192.168.1.169: bytes=32 time=4ms TTL=64
Reply from 192.168.1.169: bytes=32 time=4ms TTL=64
Ping statistics for 192.168.1.169:
    Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
    Minimum = 4ms, Maximum = 5ms, Average = 4ms
10.02.20213617Base systemBug ReportVery LowHighntpd-busybox default doesn't work with /etc/config/syst...openwrt-19.07Unconfirmed Task Description

19.07.4

Specify no busybox options in menuconfig and include an /etc/config/system ntp configuration in buildroot/files/

NTP doesn’t work, even though ntp exists via busybox. If you call ntpd and tell it to query a nameserver directly, it does get a result and set the time.

You must install ntpd, it should automatically work with busybox’s ntpd.

Bringing in ntpd also brings in:

CONFIG_PACKAGE_libmbedtls=y
# CONFIG_LIBMBEDTLS_DEBUG_C is not set
# CONFIG_PACKAGE_libnss is not set
# CONFIG_PACKAGE_libopenssl is not set
CONFIG_PACKAGE_libopenssl=y

#
# Build Options
#
# CONFIG_OPENSSL_OPTIMIZE_SPEED is not set
CONFIG_OPENSSL_WITH_ASM=y
CONFIG_OPENSSL_WITH_DEPRECATED=y
# CONFIG_OPENSSL_NO_DEPRECATED is not set
CONFIG_OPENSSL_WITH_ERROR_MESSAGES=y

#
# Protocol Support
#
CONFIG_OPENSSL_WITH_TLS13=y
# CONFIG_OPENSSL_WITH_DTLS is not set
# CONFIG_OPENSSL_WITH_NPN is not set
CONFIG_OPENSSL_WITH_SRP=y
CONFIG_OPENSSL_WITH_CMS=y

#
# Algorithm Selection
#
# CONFIG_OPENSSL_WITH_EC2M is not set
CONFIG_OPENSSL_WITH_CHACHA_POLY1305=y
CONFIG_OPENSSL_PREFER_CHACHA_OVER_GCM=y
CONFIG_OPENSSL_WITH_PSK=y

#
# Less commonly used build options
#
# CONFIG_OPENSSL_WITH_ARIA is not set
# CONFIG_OPENSSL_WITH_CAMELLIA is not set
# CONFIG_OPENSSL_WITH_IDEA is not set
# CONFIG_OPENSSL_WITH_SEED is not set
# CONFIG_OPENSSL_WITH_SM234 is not set
# CONFIG_OPENSSL_WITH_BLAKE2 is not set
# CONFIG_OPENSSL_WITH_MDC2 is not set
# CONFIG_OPENSSL_WITH_WHIRLPOOL is not set
# CONFIG_OPENSSL_WITH_COMPRESSION is not set
# CONFIG_OPENSSL_WITH_RFC3779 is not set

#
# Engine/Hardware Support
#
CONFIG_OPENSSL_ENGINE=y
# CONFIG_OPENSSL_ENGINE_BUILTIN is not set
# CONFIG_OPENSSL_WITH_GOST is not set
# CONFIG_PACKAGE_libopenssl-afalg_sync is not set
# CONFIG_PACKAGE_libopenssl-conf is not set
# CONFIG_PACKAGE_libopenssl-devcrypto is not set
# CONFIG_PACKAGE_libwolfssl is not set

#
@@ -4161,7 +4082,8 @@ CONFIG_PACKAGE_libmbedtls=y
CONFIG_PACKAGE_libblobmsg-json=y
# CONFIG_PACKAGE_libbsd is not set
# CONFIG_PACKAGE_libcanfestival is not set
# CONFIG_PACKAGE_libcap is not set
CONFIG_PACKAGE_libcap=y
# CONFIG_PACKAGE_libcap-bin is not set
# CONFIG_PACKAGE_libcares is not set
# CONFIG_PACKAGE_libcgroup is not set
# CONFIG_PACKAGE_libcharset is not set
@@ -4232,10 +4154,10 @@ CONFIG_LIBCURL_PROXY=y
# CONFIG_PACKAGE_libev is not set
# CONFIG_PACKAGE_libevdev is not set
CONFIG_PACKAGE_libevent2=y
# CONFIG_PACKAGE_libevent2-core is not set
CONFIG_PACKAGE_libevent2-core=y
# CONFIG_PACKAGE_libevent2-extra is not set
# CONFIG_PACKAGE_libevent2-openssl is not set
# CONFIG_PACKAGE_libevent2-pthreads is not set
CONFIG_PACKAGE_libevent2-pthreads=y
# CONFIG_PACKAGE_libevhtp is not set
# CONFIG_PACKAGE_libexif is not set
# CONFIG_PACKAGE_libexpat is not set
@@ -5294,9 +5216,9 @@ CONFIG_LLDPD_WITH_CUSTOM=y
# CONFIG_PACKAGE_htpdate is not set
# CONFIG_PACKAGE_linuxptp is not set
# CONFIG_PACKAGE_ntp-keygen is not set
# CONFIG_PACKAGE_ntp-utils is not set
CONFIG_PACKAGE_ntp-utils=y
# CONFIG_PACKAGE_ntpclient is not set
# CONFIG_PACKAGE_ntpd is not set
CONFIG_PACKAGE_ntpd=y
# CONFIG_PACKAGE_ntpdate is not set


11.02.20213620Base systemBug ReportVery LowHighRemote desktop unusable with software flow offloadingopenwrt-19.07Unconfirmed Task Description

I have latest stable OpenWrt 19.07.6 r11278 installed to my TP-Link TL-WDR4900 v1.
I have a port forward to a Windows RDP or using TeamViewer remote management.
When the Software flow offloading ENABLED, Windows RDP or TeamViewer remote management connection become slow and laggy.

If I disable everything works quickly without lags.

 


24.02.20213639Base systemBug ReportVery LowHighRepeated failure of wireless interfaces, seemingly rela...TrunkUnconfirmed Task Description

Supply the following if possible:



Model: Linksys WRT3200ACM
Architecture: ARMv7 Processor rev 1 (v7l)
Firmware Version: OpenWrt 19.07.7 r11306-c4a6851c72 / LuCI openwrt-19.07 branch git-21.054.03371-3b137b5
Kernel Version: 4.14.221

In the last four to six days the wireless on my network kept failing (particularly overnight - but that may be less to do with time of day and more to do with lease expiry??). I searched and found that someone else resolved this back in around 2018 by enabling IGMP Snooping and then rebooting their router (https://forum.openwrt.org/t/wifi-up-device-connected-but-no-internet/) - That worked for me but only temporarily. This morning, even though (on LuCI and via SSH) I can see IGMP Snooping is still enabled (LAN interface), the same problem occurred - all the wireless devices can connect to the router but not the Internet. For the moment, rebooting the router fixed it but clearly that’s not a realistic solution.

I have marked this high severity because:

- It looks like a regression
- My kids can't access school via their iPads and are getting marked absent! (like many/most, we're in lockdown)

`/etc/config/network` reads:

config interface 'loopback'
        option ifname 'lo'
        option proto 'static'
        option ipaddr '127.0.0.1'
        option netmask '255.0.0.0'

config globals 'globals'
        option ula_prefix 'fddf:17c3:6271::/48'

config interface 'lan'
        option type 'bridge'
        option ifname 'eth0.1'
        option proto 'static'
        option netmask '255.255.255.0'
        option ip6assign '60'
        option broadcast '192.168.7.255'
        option ipaddr '192.168.7.1'
        option gateway '****'  <- my WAN static IP
        list dns '1.1.1.1'
        option igmp_snooping '1' <- I set this, which seemed to resolve it, but only for a bit

config interface 'wan'
        option ifname 'eth1.2'
        option proto 'pppoe'
        option password '****'
        option ipv6 'auto'
        option username '****'

config interface 'wan6'
        option ifname 'eth1.2'
        option proto 'dhcpv6'

config switch
        option name 'switch0'
        option reset '1'
        option enable_vlan '1'

config switch_vlan
        option device 'switch0'
        option vlan '1'
        option ports '0 1 2 3 5t'

config switch_vlan
        option device 'switch0'
        option vlan '2'
        option ports '4 6t'

config interface 'wwan'
        option proto 'dhcp'
27.02.20213645Base systemBug ReportVery LowHighStateful DHCPv6 bugTrunkUnconfirmed Task Description

If the firmware compiled with the current source code uses Stateful DHCPv6, the IPv6 address cannot be obtained, but the DNS can be obtained. Please fix it.

04.03.20213662Base systemBug ReportVery LowHighParameters aren't passed to kernel modules at bootTrunkUnconfirmed Task Description

I have a D-Link DIR-882 A1 router (MT7621 + 2x MT7615N, 128 MB of RAM, 16 MB of NOR flash) running OpenWrt SNAPSHOT r16087-1d412235a5 (built on March 4, 2021) and I need to pass quirks=0bc2:231a:u parameter to the usb-storage module at boot in order to skip loading of the UAS driver, which is currently broken on the xhci-mtk driver this router uses (as reported here, here, here and on various topics on the OpenWrt Forums), and prevents an external USB 3.0 HDD I have to work with it.

Accordingly to several sources, this should be easily accomplished by writing usb-storage quirks=<vid>:<pid>:u on a single line into /etc/modules.d/usb-storage, however, the specified parameter is ignored and never reaches the kernel module, as running cat /sys/module/usb_storage/parameters/quirks after boot is complete returns empty. I also found this thread, dating back to 2018, with other users having the same issue, and which also seems to confirm that adding the kernel module parameters to the corresponding file under /etc/modules.d is how it’s supposed to work, but it simply doesn’t.

The only workaround I found so far is running echo “0bc2:231a:u” > /sys/module/usb_storage/parameters/quirks after booting, but then I need to physically unplug and re-plug the HDD for the changes to take effect, this also needs to be done every time the router powers on, which is very annoying. Other things I tried includes creating /etc/modprobe.d/usb-storage.conf with options usb-storage quirks=<vid>:<pid>:u and also unloading (and ever completely removing) kmod-usb-storage-uas from the device, but none of that worked.

So, is there any other mechanism for passing parameters to kernel modules at boot time? As far as I searched, /etc/modules.d seems to be the only one, but it’s broken...

22.03.20213701Base systemBug ReportVery LowHighDropbear in a crash loop TrunkUnconfirmed Task Description

Problem:
When i trying connect router by ssh i see error:

ssh: connect to host 192.168.1.1 port 22: Connection refused

OS / HW:

Model:	TP-Link TL-WR842N v5
Architecture:	MediaTek MT7628AN ver:1 eco:2
Firmware Version:	OpenWrt SNAPSHOT r16217-d7c8ca4d0b / LuCI Master git-21.081.27815-c385df1
Kernel Version:	5.4.105

Logs:

Mon Mar 22 12:04:39 2021 daemon.info procd: Instance dropbear::instance1 s in a crash loop 6 crashes, 0 seconds since last crash

I tried master and openwrt-21.02 branch. Same results.

My config:

CONFIG_TARGET_ramips=y
CONFIG_TARGET_ramips_mt76x8=y
CONFIG_TARGET_ramips_mt76x8_DEVICE_tplink_tl-wr842n-v5=y
CONFIG_BUSYBOX_CUSTOM=y
CONFIG_BUILD_PATENTED=y
CONFIG_BUSYBOX_CONFIG_ARP=y
# CONFIG_BUSYBOX_CONFIG_FEATURE_ALLOW_EXEC is not set
# CONFIG_BUSYBOX_CONFIG_MKSWAP is not set
# CONFIG_BUSYBOX_CONFIG_SWAPOFF is not set
# CONFIG_BUSYBOX_CONFIG_SWAPON is not set
# CONFIG_BUSYBOX_CONFIG_VI is not set
CONFIG_CLEAN_IPKG=y
CONFIG_EXPERIMENTAL=y
# CONFIG_KERNEL_AIO is not set
# CONFIG_KERNEL_CGROUPS is not set
# CONFIG_KERNEL_ELF_CORE is not set
# CONFIG_KERNEL_FANOTIFY is not set
# CONFIG_KERNEL_FHANDLE is not set
# CONFIG_KERNEL_KEYS is not set
# CONFIG_KERNEL_NAMESPACES is not set
# CONFIG_KERNEL_SECCOMP is not set
# CONFIG_KERNEL_SWAP is not set
CONFIG_LIBCURL_COOKIES=y
CONFIG_LIBCURL_FTP=y
CONFIG_LIBCURL_HTTP=y
CONFIG_LIBCURL_NO_SMB="!"
CONFIG_LIBCURL_OPENSSL=y
CONFIG_LIBCURL_PROXY=y
CONFIG_LIBSODIUM_MINIMAL=y
CONFIG_LINUX_5_10=y
CONFIG_LUCI_SRCDIET=y
CONFIG_OPENSSL_ENGINE=y
CONFIG_OPENSSL_PREFER_CHACHA_OVER_GCM=y
CONFIG_OPENSSL_WITH_ASM=y
CONFIG_OPENSSL_WITH_CHACHA_POLY1305=y
CONFIG_OPENSSL_WITH_CMS=y
CONFIG_OPENSSL_WITH_DEPRECATED=y
CONFIG_OPENSSL_WITH_ERROR_MESSAGES=y
CONFIG_OPENSSL_WITH_PSK=y
CONFIG_OPENSSL_WITH_SRP=y
CONFIG_OPENSSL_WITH_TLS13=y
CONFIG_PACKAGE_cgi-io=y
CONFIG_PACKAGE_chat=y
CONFIG_PACKAGE_comgt=y
CONFIG_PACKAGE_curl=y
CONFIG_PACKAGE_htop=y
CONFIG_PACKAGE_ip-tiny=y
CONFIG_PACKAGE_ipset=y
CONFIG_PACKAGE_iptables-mod-conntrack-extra=y
CONFIG_PACKAGE_iptables-mod-ipopt=y
CONFIG_PACKAGE_kmod-ipt-conntrack-extra=y
CONFIG_PACKAGE_kmod-ipt-ipopt=y
CONFIG_PACKAGE_kmod-ipt-ipset=y
CONFIG_PACKAGE_kmod-ipt-raw=y
CONFIG_PACKAGE_kmod-mii=y
CONFIG_PACKAGE_kmod-nfnetlink=y
CONFIG_PACKAGE_kmod-tun=y
CONFIG_PACKAGE_kmod-usb-acm=y
CONFIG_PACKAGE_kmod-usb-net=y
CONFIG_PACKAGE_kmod-usb-net-cdc-ether=y
CONFIG_PACKAGE_kmod-usb-serial=y
CONFIG_PACKAGE_kmod-usb-serial-option=y
CONFIG_PACKAGE_kmod-usb-serial-pl2303=y
CONFIG_PACKAGE_kmod-usb-serial-wwan=y
CONFIG_PACKAGE_libatomic=y
CONFIG_PACKAGE_libcares=y
CONFIG_PACKAGE_libcbor=y
CONFIG_PACKAGE_libcurl=y
CONFIG_PACKAGE_libev=y
CONFIG_PACKAGE_libevdev=y
CONFIG_PACKAGE_libfido2=y
CONFIG_PACKAGE_libipset=y
CONFIG_PACKAGE_libiwinfo-lua=y
CONFIG_PACKAGE_liblua=y
CONFIG_PACKAGE_liblucihttp=y
CONFIG_PACKAGE_liblucihttp-lua=y
CONFIG_PACKAGE_liblzo=y
CONFIG_PACKAGE_libmnl=y
CONFIG_PACKAGE_libncurses=y
CONFIG_PACKAGE_libopenssl=y
CONFIG_PACKAGE_libopenssl-conf=y
CONFIG_PACKAGE_librt=y
CONFIG_PACKAGE_libsodium=y
CONFIG_PACKAGE_libubus-lua=y
CONFIG_PACKAGE_libuci-lua=y
CONFIG_PACKAGE_libudev-zero=y
CONFIG_PACKAGE_libusb-1.0=y
CONFIG_PACKAGE_libustream-openssl=y
# CONFIG_PACKAGE_libustream-wolfssl is not set
# CONFIG_PACKAGE_libwolfssl is not set
CONFIG_PACKAGE_lua=y
CONFIG_PACKAGE_luci=y
CONFIG_PACKAGE_luci-app-firewall=y
CONFIG_PACKAGE_luci-app-opkg=y
CONFIG_PACKAGE_luci-base=y
CONFIG_PACKAGE_luci-compat=y
CONFIG_PACKAGE_luci-lib-base=y
CONFIG_PACKAGE_luci-lib-httpprotoutils=y
CONFIG_PACKAGE_luci-lib-ip=y
CONFIG_PACKAGE_luci-lib-jsonc=y
CONFIG_PACKAGE_luci-lib-nixio=y
CONFIG_PACKAGE_luci-mod-admin-full=y
CONFIG_PACKAGE_luci-mod-network=y
CONFIG_PACKAGE_luci-mod-status=y
CONFIG_PACKAGE_luci-mod-system=y
CONFIG_PACKAGE_luci-proto-3g=y
CONFIG_PACKAGE_luci-proto-ipv6=y
CONFIG_PACKAGE_luci-proto-ppp=y
CONFIG_PACKAGE_luci-theme-bootstrap=y
CONFIG_PACKAGE_nano=y
# CONFIG_PACKAGE_odhcp6c is not set
CONFIG_PACKAGE_odhcpd=y
# CONFIG_PACKAGE_odhcpd-ipv6only is not set
CONFIG_PACKAGE_odhcpd_full_ext_cer_id=0
CONFIG_PACKAGE_openssl-util=y
CONFIG_PACKAGE_rpcd=y
CONFIG_PACKAGE_rpcd-mod-file=y
CONFIG_PACKAGE_rpcd-mod-iwinfo=y
CONFIG_PACKAGE_rpcd-mod-luci=y
CONFIG_PACKAGE_rpcd-mod-rrdns=y
CONFIG_PACKAGE_terminfo=y
CONFIG_PACKAGE_uhttpd=y
CONFIG_PACKAGE_uhttpd-mod-ubus=y
CONFIG_PACKAGE_usb-modeswitch=y
CONFIG_PACKAGE_usbids=y
CONFIG_PACKAGE_usbutils=y
CONFIG_PACKAGE_wpad-basic=y
# CONFIG_PACKAGE_wpad-basic-wolfssl is not set
CONFIG_PACKAGE_zlib=y
CONFIG_STRIP_KERNEL_EXPORTS=y
# CONFIG_TARGET_ROOTFS_INITRAMFS is not set
CONFIG_TESTING_KERNEL=y
CONFIG_USE_MKLIBS=y
# CONFIG_WPA_WOLFSSL is not set
# CONFIG_LIBCURL_FILE is not set

07.04.20213729Base systemBug ReportVery LowHighRT2800 (MT7620) no multiple SSIDTrunkUnconfirmed Task Description

master branch

MT7620
Nexx WT3020 8M

config wifi-device ‘radio0’

option type 'mac80211'
option channel '11'
option hwmode '11g'
option path 'platform/10180000.wmac'
option cell_density '0'
option htmode 'HT40'
option noscan '1'

config wifi-iface ‘wifinet0’

option device 'radio0'
option mode 'ap'
option encryption 'none'
option network 'lan2'
option ssid 'Public'

config wifi-iface ‘wifinet1’

option device 'radio0'
option mode 'ap'
option encryption 'none'
option network 'lan'
option ssid 'Private2'

only “Public” wifi shows

wlan0 Link encap:Ethernet HWaddr 38:xxxxxxxxxxx

        inet addr:192.168.182.1  Bcast:192.168.255.255  Mask:255.255.0.0
        inet6 addr: fe80::3a1c:4aff:fe06:c05b/64 Scope:Link
        UP BROADCAST RUNNING PROMISC MULTICAST  MTU:1500  Metric:1
        RX packets:0 errors:0 dropped:0 overruns:0 frame:0
        TX packets:11 errors:0 dropped:0 overruns:0 carrier:0
        collisions:0 txqueuelen:1000 
        RX bytes:0 (0.0 B)  TX bytes:1140 (1.1 KiB)
 


Showing tasks 101 - 150 of 1150 Page 3 of 23 - 1 - 2 - 3 - 4 - 5 - Last >>

Available keyboard shortcuts

Tasklist

Task Details

Task Editing