OpenWrt/LEDE Project

Welcome to the OpenWrt/LEDE Project bug reporting and issue tracking system

Problems to be reported here are for the OpenWrt/LEDE Project targets, sources, toolchain, core packages, build procedures, distribution and infrastructure. Guidelines for submitting a good bug report can be found at the OpenWrt/LEDE Project website. Problems related to LuCI or OpenWrt packages need to be reported in their repositories:

Notifications of all submissions and task changes are sent to lede-bugs@infradead.org.

OpenedIDCategoryTask TypePrioritySeveritySummaryReported InStatus
14.04.20203008KernelBug ReportVery LowHighGenesys Logic USB 3.0 hub not recognized by the systemAllUnconfirmed Task Description

Hi) I have a problem with Genesys Logic USB 3.0 hub (based on GL3523) on my Xiaomi MiR3G. The system don’t see this hub. Same on 4.14 & 4.19 kernel. Bought on AliExpress

Workaround: insert a half of the plug into router port → the system recognize USB 2.0 hub, then insert the plug to the end → the system recognize USB 2.0 & USB 3.0 hubs as it must be.
1. Normal connect hub → the log is empty.
2. Insert a half of the plug:

root@MI-R3G:~# lsusb -v

Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               3.00
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         3
  bMaxPacketSize0         9
  idVendor           0x1d6b Linux Foundation
  idProduct          0x0003 3.0 root hub
  bcdDevice            4.19
  iManufacturer           3 Linux 4.19.114 xhci-hcd
  iProduct                2 xHCI Host Controller
  iSerial                 1 1e1c0000.xhci
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           31
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0 Full speed (or root) hub
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0004  1x 4 bytes
        bInterval              12
        bMaxBurst               0
Hub Descriptor:
  bLength              12
  bDescriptorType      42
  nNbrPorts             1
  wHubCharacteristic 0x0009
    Per-port power switching
    Per-port overcurrent protection
  bPwrOn2PwrGood       10 * 2 milli seconds
  bHubContrCurrent      0 milli Ampere
  bHubDecLat          0.0 micro seconds
  wHubDelay             0 nano seconds
  DeviceRemovable    0x00
 Hub Port Status:
   Port 1: 0000.02a0 5Gbps power Rx.Detect
Binary Object Store Descriptor:
  bLength                 5
  bDescriptorType        15
  wTotalLength           15
  bNumDeviceCaps          1
  SuperSpeed USB Device Capability:
    bLength                10
    bDescriptorType        16
    bDevCapabilityType      3
    bmAttributes         0x00
    wSpeedsSupported   0x0008
      Device can operate at SuperSpeed (5Gbps)
    bFunctionalitySupport   3
      Lowest fully-functional device speed is SuperSpeed (5Gbps)
    bU1DevExitLat           0 micro seconds
    bU2DevExitLat           0 micro seconds
Device Status:     0x0001
  Self Powered

Bus 001 Device 010: ID 05e3:0610 Genesys Logic, Inc. 4-port hub
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         2 TT per port
  bMaxPacketSize0        64
  idVendor           0x05e3 Genesys Logic, Inc.
  idProduct          0x0610 4-port hub
  bcdDevice            5.11
  iManufacturer           1 GenesysLogic
  iProduct                2 USB2.0 Hub
  iSerial                 0
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           41
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower              100mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      1 Single TT
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0001  1x 1 bytes
        bInterval              12
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       1
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      2 TT per port
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0001  1x 1 bytes
        bInterval              12
Hub Descriptor:
  bLength               9
  bDescriptorType      41
  nNbrPorts             4
  wHubCharacteristic 0x00e9
    Per-port power switching
    Per-port overcurrent protection
    TT think time 32 FS bits
    Port indicators
  bPwrOn2PwrGood       50 * 2 milli seconds
  bHubContrCurrent    100 milli Ampere
  DeviceRemovable    0x00
  PortPwrCtrlMask    0xff
 Hub Port Status:
   Port 1: 0000.0100 power
   Port 2: 0000.0100 power
   Port 3: 0000.0100 power
   Port 4: 0000.0100 power
Device Qualifier (for other device speed):
  bLength                10
  bDescriptorType         6
  bcdUSB               2.00
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         0 Full speed (or root) hub
  bMaxPacketSize0        64
  bNumConfigurations      1
Device Status:     0x0001
  Self Powered

Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         1 Single TT
  bMaxPacketSize0        64
  idVendor           0x1d6b Linux Foundation
  idProduct          0x0002 2.0 root hub
  bcdDevice            4.19
  iManufacturer           3 Linux 4.19.114 xhci-hcd
  iProduct                2 xHCI Host Controller
  iSerial                 1 1e1c0000.xhci
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           25
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0 Full speed (or root) hub
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0004  1x 4 bytes
        bInterval              12
Hub Descriptor:
  bLength               9
  bDescriptorType      41
  nNbrPorts             2
  wHubCharacteristic 0x0009
    Per-port power switching
    Per-port overcurrent protection
    TT think time 8 FS bits
  bPwrOn2PwrGood       10 * 2 milli seconds
  bHubContrCurrent      0 milli Ampere
  DeviceRemovable    0x00
  PortPwrCtrlMask    0xff
 Hub Port Status:
   Port 1: 0000.0503 highspeed power enable connect
   Port 2: 0000.0100 power
Device Status:     0x0001
  Self Powered

3. Insert the plug to the end:

root@MI-R3G:~# lsusb -v

Bus 001 Device 010: ID 05e3:0610 Genesys Logic, Inc. 4-port hub
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         2 TT per port
  bMaxPacketSize0        64
  idVendor           0x05e3 Genesys Logic, Inc.
  idProduct          0x0610 4-port hub
  bcdDevice            5.11
  iManufacturer           1 GenesysLogic
  iProduct                2 USB2.0 Hub
  iSerial                 0
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           41
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower              100mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      1 Single TT
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0001  1x 1 bytes
        bInterval              12
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       1
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      2 TT per port
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0001  1x 1 bytes
        bInterval              12
Hub Descriptor:
  bLength               9
  bDescriptorType      41
  nNbrPorts             4
  wHubCharacteristic 0x00e9
    Per-port power switching
    Per-port overcurrent protection
    TT think time 32 FS bits
    Port indicators
  bPwrOn2PwrGood       50 * 2 milli seconds
  bHubContrCurrent    100 milli Ampere
  DeviceRemovable    0x00
  PortPwrCtrlMask    0xff
 Hub Port Status:
   Port 1: 0000.0100 power
   Port 2: 0000.0100 power
   Port 3: 0000.0100 power
   Port 4: 0000.0100 power
Device Qualifier (for other device speed):
  bLength                10
  bDescriptorType         6
  bcdUSB               2.10
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         0 Full speed (or root) hub
  bMaxPacketSize0        64
  bNumConfigurations      1
Device Status:     0x0001
  Self Powered

Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         1 Single TT
  bMaxPacketSize0        64
  idVendor           0x1d6b Linux Foundation
  idProduct          0x0002 2.0 root hub
  bcdDevice            4.19
  iManufacturer           3 Linux 4.19.114 xhci-hcd
  iProduct                2 xHCI Host Controller
  iSerial                 1 1e1c0000.xhci
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           25
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0 Full speed (or root) hub
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0004  1x 4 bytes
        bInterval              12
Hub Descriptor:
  bLength               9
  bDescriptorType      41
  nNbrPorts             2
  wHubCharacteristic 0x0009
    Per-port power switching
    Per-port overcurrent protection
    TT think time 8 FS bits
  bPwrOn2PwrGood       10 * 2 milli seconds
  bHubContrCurrent      0 milli Ampere
  DeviceRemovable    0x00
  PortPwrCtrlMask    0xff
 Hub Port Status:
   Port 1: 0000.0503 highspeed power enable connect
   Port 2: 0000.0100 power
Device Status:     0x0001
  Self Powered

Bus 002 Device 006: ID 05e3:0620 Genesys Logic, Inc.
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               3.00
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         3
  bMaxPacketSize0         9
  idVendor           0x05e3 Genesys Logic, Inc.
  idProduct          0x0620
  bcdDevice            5.11
  iManufacturer           1 GenesysLogic
  iProduct                2 USB3.0 Hub
  iSerial                 0
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           31
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0 Full speed (or root) hub
      iInterface              1 GenesysLogic
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x83  EP 3 IN
        bmAttributes           19
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Feedback
        wMaxPacketSize     0x0002  1x 2 bytes
        bInterval               8
        bMaxBurst               0
Hub Descriptor:
  bLength              12
  bDescriptorType      42
  nNbrPorts             4
  wHubCharacteristic 0x0009
    Per-port power switching
    Per-port overcurrent protection
  bPwrOn2PwrGood       50 * 2 milli seconds
  bHubContrCurrent    576 milli Ampere
  bHubDecLat          0.4 micro seconds
  wHubDelay          1508 nano seconds
  DeviceRemovable    0x00
 Hub Port Status:
   Port 1: 0000.02a0 5Gbps power Rx.Detect
   Port 2: 0000.02a0 5Gbps power Rx.Detect
   Port 3: 0000.02a0 5Gbps power Rx.Detect
   Port 4: 0000.02a0 5Gbps power Rx.Detect
Binary Object Store Descriptor:
  bLength                 5
  bDescriptorType        15
  wTotalLength           42
  bNumDeviceCaps          3
  USB 2.0 Extension Device Capability:
    bLength                 7
    bDescriptorType        16
    bDevCapabilityType      2
    bmAttributes   0x00000006
      Link Power Management (LPM) Supported
  SuperSpeed USB Device Capability:
    bLength                10
    bDescriptorType        16
    bDevCapabilityType      3
    bmAttributes         0x00
    wSpeedsSupported   0x000e
      Device can operate at Full Speed (12Mbps)
      Device can operate at High Speed (480Mbps)
      Device can operate at SuperSpeed (5Gbps)
    bFunctionalitySupport   1
      Lowest fully-functional device speed is Full Speed (12Mbps)
    bU1DevExitLat           8 micro seconds
    bU2DevExitLat         190 micro seconds
  Container ID Device Capability:
    bLength                20
    bDescriptorType        16
    bDevCapabilityType      4
    bReserved               0
    ContainerID             {f0564b9f-f61d-e011-ac64-0800200c9a66}
Device Status:     0x0001
  Self Powered

Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               3.00
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         3
  bMaxPacketSize0         9
  idVendor           0x1d6b Linux Foundation
  idProduct          0x0003 3.0 root hub
  bcdDevice            4.19
  iManufacturer           3 Linux 4.19.114 xhci-hcd
  iProduct                2 xHCI Host Controller
  iSerial                 1 1e1c0000.xhci
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           31
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0 Full speed (or root) hub
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0004  1x 4 bytes
        bInterval              12
        bMaxBurst               0
Hub Descriptor:
  bLength              12
  bDescriptorType      42
  nNbrPorts             1
  wHubCharacteristic 0x0009
    Per-port power switching
    Per-port overcurrent protection
  bPwrOn2PwrGood       10 * 2 milli seconds
  bHubContrCurrent      0 milli Ampere
  bHubDecLat          0.0 micro seconds
  wHubDelay             0 nano seconds
  DeviceRemovable    0x00
 Hub Port Status:
   Port 1: 0000.0203 5Gbps power U0 enable connect
Binary Object Store Descriptor:
  bLength                 5
  bDescriptorType        15
  wTotalLength           15
  bNumDeviceCaps          1
  SuperSpeed USB Device Capability:
    bLength                10
    bDescriptorType        16
    bDevCapabilityType      3
    bmAttributes         0x00
    wSpeedsSupported   0x0008
      Device can operate at SuperSpeed (5Gbps)
    bFunctionalitySupport   3
      Lowest fully-functional device speed is SuperSpeed (5Gbps)
    bU1DevExitLat           0 micro seconds
    bU2DevExitLat           0 micro seconds
Device Status:     0x0001
  Self Powered

But after reboot the same: no hub at all.
Nope, the connector is normal, recognized correctly on PC & smartphone. So, this is kernel or driver bug.

13.04.20203006PackagesBug ReportVery LowMediumdnsmasq-full fails to resolve Cloudflare domains if DNS...openwrt-19.07Unconfirmed Task Description

dnsmasq fails to resolve Cloudflare domains if DNSSEC is enabled.

# ping www.galeria.de
ping: bad address 'www.galeria.de'

# nslookup www.galeria.de
Server:         127.0.0.1
Address:        127.0.0.1#53

** server can't find www.galeria.de: SERVFAIL
Name:      www.galeria.de
www.galeria.de  canonical name = www.galeria.de.cdn.cloudflare.net

/etc/config/dhcp

# cat /etc/config/dhcp

config dnsmasq
        option domainneeded '1'
        option boguspriv '1'
        option filterwin2k '0'
        option localise_queries '1'
        option rebind_protection '1'
        option rebind_localhost '1'
        option expandhosts '1'
        option nonegcache       0
        option authoritative '1'
        option readethers '1'
        option leasefile '/tmp/dhcp.leases'
        option resolvfile '/tmp/resolv.conf.auto'
        option nonwildcard '1'
        option localservice '1'
        option domain 'fritz.box'
        option local '/box/'
        option nonegcache '0'
        option dnssec '1'
        option dnsseccheckunsigned '1'
        option logqueries '1'
        option logfacility '/tmp/dnsmasq.log'

config dhcp 'lan'
        option interface 'lan'
        option limit '150'
        option leasetime '12h'
        option dhcpv6 'server'
        option ra 'server'
        option start '2'
        option ra_management '1'

config dhcp 'wan'
        option interface 'wan'
        option ignore '1

This is the generated dnsmasq configuration file

# cat /var/etc/dnsmasq.conf.cfg01411c
# auto-generated config file from /etc/config/dhcp
conf-file=/etc/dnsmasq.conf
dhcp-authoritative
domain-needed
log-queries=extra
localise-queries
read-ethers
enable-ubus
expand-hosts
bind-dynamic
local-service
log-facility=/tmp/dnsmasq.log
domain=fritz.box
server=/box/
dhcp-leasefile=/tmp/dhcp.leases
resolv-file=/tmp/resolv.conf.auto
stop-dns-rebind
rebind-localhost-ok
conf-file=/usr/share/dnsmasq/trust-anchors.conf
dnssec
dnssec-no-timecheck
dnssec-check-unsigned
dhcp-broadcast=tag:needs-broadcast
addn-hosts=/tmp/hosts
conf-dir=/tmp/dnsmasq.d
user=dnsmasq
group=dnsmasq

dhcp-ignore-names=tag:dhcp_bogus_hostname
conf-file=/usr/share/dnsmasq/dhcpbogushostname.conf

bogus-priv
conf-file=/usr/share/dnsmasq/rfc6761.conf
dhcp-range=set:lan,192.168.222.2,192.168.222.151,255.255.255.0,12h

For additional debugging I also compiled the dnsmasq package from https://github.com/openwrt/openwrt/tree/v19.07.2/package/network/services/dnsmasq on Linux (openSUSE Tumbleweed) and there dnsmasq works without problems.

# cat /etc/os-release | head -n2
NAME="openSUSE Tumbleweed"
# VERSION="20200410"
# sudo src/dnsmasq --version
Dnsmasq version 2.80  Copyright (c) 2000-2018 Simon Kelley
Compile time options: IPv6 GNU-getopt DBus no-i18n no-IDN DHCP DHCPv6 no-Lua TFTP conntrack ipset auth DNSSEC loop-detect inotify dumpfile

This software comes with ABSOLUTELY NO WARRANTY.
Dnsmasq is free software, and you are welcome to redistribute it
under the terms of the GNU General Public License, version 2 or 3.

# nslookup www.galeria.de
Server:         127.0.0.1
Address:        127.0.0.1#53

Non-authoritative answer:
www.galeria.de  canonical name = www.galeria.de.cdn.cloudflare.net.
Name:   www.galeria.de.cdn.cloudflare.net
Address: 104.16.230.136
Name:   www.galeria.de.cdn.cloudflare.net
Address: 104.16.231.136

I use OpenWrt 19.07.2 r10947-65030d81f3 with dnsmasq-full - 2.80-16 on a Linksys 1900ACS router.

13.04.20203005Base systemBug ReportVery LowHighiptables ruleset order improvement optionTrunkUnconfirmed Task Description

Supply the following if possible:
- Device problem occurs on
TP-Link Archer C7 v5
- Software versions of OpenWrt/LEDE release, packages, etc.
19.07.2, just default packages
- Steps to reproduce
Current iptable ordering is badly pessimal (this repeats 3x, so 3 states get set for each connection, but thats for other news)
```
-A FORWARD -m comment –comment “!fw3: Custom forwarding rule chain” -j forwarding_rule
-A FORWARD -m conntrack –ctstate RELATED,ESTABLISHED -m comment –comment “!fw3” -j ACCEPT
-A FORWARD -m conntrack –ctstate INVALID -m comment –comment “!fw3” -j DROP
```
following does same job but does significantly less processing for typical case of in-state packets
```
-A FORWARD -m conntrack –ctstate RELATED,ESTABLISHED -m comment –comment “!fw3” -j ACCEPT
-A FORWARD -m conntrack –ctstate INVALID -m comment –comment “!fw3” -j DROP
-A FORWARD -m comment –comment “!fw3: Custom forwarding rule chain” -j forwarding_rule
```
Not willing to generalize, but my wifi and wire behind could not reach subscription 100Mbps in any way before the change, after change it is steady 100Mbps both ways.

13.04.20203004PackagesBug ReportVery LowLowNTPD launching script can't startopenwrt-18.06Unconfirmed Task Description

hello all,

I can launch NTP by :

/usr/sbin/ntpd -n -N -l -S /usr/sbin/ntpd-hotplug 0.openwrt.pool.ntp.org ntp.lothaire.net ntp.ciril.fr 1.fr.pool.ntp.org debian.org

When i use Luci web client and use it to configure ntp the result is :

/usr/sbin/ntpd -n -N -l -S -p /usr/sbin/ntpd-hotplug -p 0.openwrt.pool.ntp.org -p ntp.lothaire.net -p ntp.ciril.fr -p 1.fr.pool.ntp.org debian.org

and so it doesn't start.

In my init script /etc/init.d/sysntpd I changed the line 55 by

              
procd_append_param command $peer

(removed -p)

and look like it's works perfectly.

13.04.20203003Base systemBug ReportVery LowLowNTPD launching script can't startTrunkUnconfirmed Task Description

hello all,

I can launch NTP by :

/usr/sbin/ntpd -n -N -l -S /usr/sbin/ntpd-hotplug 0.openwrt.pool.ntp.org ntp.lothaire.net ntp.ciril.fr 1.fr.pool.ntp.org debian.org

When i use Luci web client and use it to configure ntp the result is :

/usr/sbin/ntpd -n -N -l -S -p /usr/sbin/ntpd-hotplug -p 0.openwrt.pool.ntp.org -p ntp.lothaire.net -p ntp.ciril.fr -p 1.fr.pool.ntp.org debian.org

and so it doesn't start.

In my init script /etc/init.d/sysntpd I changed the line 55 by

              
procd_append_param command $peer

(removed -p)

and look like it's work perfectly.

13.04.20203002PackagesBug ReportVery LowLowNTPD launching script can't startopenwrt-18.06Unconfirmed Task Description

hello all,

I can launch NTP by :

/usr/sbin/ntpd -n -N -l -S /usr/sbin/ntpd-hotplug 0.openwrt.pool.ntp.org ntp.lothaire.net ntp.ciril.fr 1.fr.pool.ntp.org debian.org

When i use Luci web client and use it to configure ntp the result is :

/usr/sbin/ntpd -n -N -l -S -p /usr/sbin/ntpd-hotplug -p 0.openwrt.pool.ntp.org -p ntp.lothaire.net -p ntp.ciril.fr -p 1.fr.pool.ntp.org debian.org

and so it doesn't start.

In my init script /etc/init.d/sysntpd I changed the line 55 by :

              
procd_append_param command $peer


(removed -p)

and look like it's work perfectly.

12.04.20202996KernelBug ReportVery LowCriticalnanopi air cannot start in kernel 5.4.31TrunkUnconfirmed Task Description

device: nanopi air
steps:

1. "git check" to get the last trunk
2. "make menuconfig" select the device "nanopi air"
3. then "make" to get the rom and dd it into TF card
4. power on and you will see stop at "Starting kernel ..."

here is my system log:

U-Boot SPL 2020.01 (Apr 09 2020 - 20:09:21 +0000)
DRAM: 512 MiB
Trying to boot from MMC1


U-Boot 2020.01 (Apr 09 2020 - 20:09:21 +0000) Allwinner Technology

CPU:   Allwinner H3 (SUN8I 1680)
Model: FriendlyARM NanoPi NEO
DRAM:  512 MiB
MMC:   mmc@1c0f000: 0
Loading Environment from FAT... *** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   phy interface0

Error: ethernet@1c30000 address not set.
No ethernet found.

starting USB...
Bus usb@1c1a000: USB EHCI 1.00
Bus usb@1c1a400: USB OHCI 1.0
Bus usb@1c1d000: USB EHCI 1.00
Bus usb@1c1d400: USB OHCI 1.0
scanning bus usb@1c1a000 for devices... 1 USB Device(s) found
scanning bus usb@1c1a400 for devices... 1 USB Device(s) found
scanning bus usb@1c1d000 for devices... 1 USB Device(s) found
scanning bus usb@1c1d400 for devices... 1 USB Device(s) found
       scanning usb for storage devices... 0 Storage Device(s) found
Hit any key to stop autoboot:  0
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
Found U-Boot script /boot.scr
377 bytes read in 2 ms (183.6 KiB/s)
## Executing script at 43100000
3078032 bytes read in 142 ms (20.7 MiB/s)
19497 bytes read in 3 ms (6.2 MiB/s)
## Booting kernel from Legacy Image at 42000000 ...
   Image Name:   ARM OpenWrt Linux-5.4.31
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3077968 Bytes = 2.9 MiB
   Load Address: 40008000
   Entry Point:  40008000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 43000000
   Booting using the fdt blob at 0x43000000
EHCI failed to shut down host controller.
   Loading Kernel Image
   Using Device Tree in place at 43000000, end 43007c28

Starting kernel ...
11.04.20202994Base systemBug ReportVery LowLowMT7621 DSA: no VLAN tags on egress...TrunkUnconfirmed Task Description

create an interface:

ip link add link lan1 name lan1.117 type vlan id 117
ip link set lan1 up
ip link set lan1.117 up
ip addr add 192.168.117.7/24 dev lan1.117

Sniffing with tcpdump on LAN1, tcpdump -i lan1 -e, it claims that the packets on egress are tagged.
Sniffing with a PC on the network, the packets from the router are untagged. Packets are not forwarded by VLAN activated switch.
Ingress works as expected.
Same behaviour for all interfaces type IFACEx.VID, so also bridges, e.g. br0.117...

Kernel:

[ 0.000000] Linux version 5.4.31 (dl3it-mi3g@mySpace) (gcc version 8.4.0 (Ope
nWrt GCC 8.4.0 r12869-85aef6f627)) #0 SMP Thu Apr 9 07:54:02 2020
[ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[ 0.000000] printk: bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[ 0.000000] MIPS: machine is Xiaomi Mi Router 3G v2

11.04.20202993Base systemBug ReportVery LowMediumArcher C7 v2 5GHz radio doesn't receive DHCPACKopenwrt-19.07Unconfirmed Task Description

Supply the following if possible:

Device problem occurs on

  • Archer C7 V2 (eu)

Software versions of OpenWrt/LEDE release, packages, etc.

Affects versions:

  • 19.07.0
  • 19.07.2

Tested working

  • 18.06.2
  • 18.06.8

Steps to reproduce

  1. Clean flash of 19.x sysupgrade image
  2. Enable 5ghz AP with default settings
  3. Connect to 5ghz with client

Observed Behaviour:

  • Client can authenticate
  • DHCP handshake initiated but not completed

Other notes:

  • If client also connected by ethernet, DHCPACK is received and connection successful. Client continues to have network access over wifi for ~15 seconds after disconnecting ethernet, then disassociates. See log #2.
  • Noticed 5ghz AP non-functional while investigating different issue where all 2.4g clients dropped until radio restarted.
  • Hopefully this is helpful, I am not sure how to debug any deeper than this.

Log 1 - logread during client connection attempts

	Sat Apr 11 11:10:21 2020 daemon.info hostapd: wlan0: STA 6c:40:08:9f:5b:bc IEEE 802.11: authenticated
	Sat Apr 11 00:28:20 2020 daemon.info dnsmasq-dhcp[7552]: DHCPDISCOVER(br-lan) 6c:40:08:9f:5b:bc
	Sat Apr 11 00:28:20 2020 daemon.info dnsmasq-dhcp[7552]: DHCPOFFER(br-lan) 192.168.12.240 6c:40:08:9f:5b:bc
	Sat Apr 11 00:28:20 2020 daemon.notice hostapd: wlan0: AP-STA-DISCONNECTED 6c:40:08:9f:5b:bc
	Sat Apr 11 00:28:20 2020 daemon.info hostapd: wlan0: STA 6c:40:08:9f:5b:bc IEEE 802.11: disassociated
	Sat Apr 11 00:28:21 2020 daemon.info hostapd: wlan0: STA 6c:40:08:9f:5b:bc IEEE 802.11: deauthenticated due to inactivity (timer DEAUTH/REMOVE)
	Sat Apr 11 00:28:22 2020 daemon.info hostapd: wlan0: STA 6c:40:08:9f:5b:bc IEEE 802.11: authenticated
	Sat Apr 11 00:28:22 2020 daemon.info hostapd: wlan0: STA 6c:40:08:9f:5b:bc IEEE 802.11: associated (aid 2)
	Sat Apr 11 00:28:22 2020 daemon.notice hostapd: wlan0: AP-STA-CONNECTED 6c:40:08:9f:5b:bc
	Sat Apr 11 00:28:22 2020 daemon.info hostapd: wlan0: STA 6c:40:08:9f:5b:bc WPA: pairwise key handshake completed (RSN)
	Sat Apr 11 00:28:24 2020 daemon.info dnsmasq-dhcp[7552]: DHCPDISCOVER(br-lan) 6c:40:08:9f:5b:bc
	Sat Apr 11 00:28:24 2020 daemon.info dnsmasq-dhcp[7552]: DHCPOFFER(br-lan) 192.168.12.240 6c:40:08:9f:5b:bc
	Sat Apr 11 00:28:27 2020 daemon.info dnsmasq-dhcp[7552]: DHCPDISCOVER(br-lan) 6c:40:08:9f:5b:bc
	Sat Apr 11 00:28:27 2020 daemon.info dnsmasq-dhcp[7552]: DHCPOFFER(br-lan) 192.168.12.240 6c:40:08:9f:5b:bc
	Sat Apr 11 00:28:31 2020 daemon.info dnsmasq-dhcp[7552]: DHCPDISCOVER(br-lan) 6c:40:08:9f:5b:bc
	Sat Apr 11 00:28:31 2020 daemon.info dnsmasq-dhcp[7552]: DHCPOFFER(br-lan) 192.168.12.240 6c:40:08:9f:5b:bc
	Sat Apr 11 00:28:39 2020 daemon.info dnsmasq-dhcp[7552]: DHCPDISCOVER(br-lan) 6c:40:08:9f:5b:bc
	Sat Apr 11 00:28:39 2020 daemon.info dnsmasq-dhcp[7552]: DHCPOFFER(br-lan) 192.168.12.240 6c:40:08:9f:5b:bc
	Sat Apr 11 00:28:47 2020 daemon.info dnsmasq-dhcp[7552]: DHCPDISCOVER(br-lan) 6c:40:08:9f:5b:bc
	Sat Apr 11 00:28:47 2020 daemon.info dnsmasq-dhcp[7552]: DHCPOFFER(br-lan) 192.168.12.240 6c:40:08:9f:5b:bc
	Sat Apr 11 00:28:56 2020 daemon.info dnsmasq-dhcp[7552]: DHCPDISCOVER(br-lan) 6c:40:08:9f:5b:bc
	Sat Apr 11 00:28:56 2020 daemon.info dnsmasq-dhcp[7552]: DHCPOFFER(br-lan) 192.168.12.240 6c:40:08:9f:5b:bc
	Sat Apr 11 00:29:04 2020 daemon.info dnsmasq-dhcp[7552]: DHCPDISCOVER(br-lan) 6c:40:08:9f:5b:bc
	Sat Apr 11 00:29:04 2020 daemon.info dnsmasq-dhcp[7552]: DHCPOFFER(br-lan) 192.168.12.240 6c:40:08:9f:5b:bc
	Sat Apr 11 00:29:13 2020 daemon.info dnsmasq-dhcp[7552]: DHCPDISCOVER(br-lan) 6c:40:08:9f:5b:bc
	Sat Apr 11 00:29:13 2020 daemon.info dnsmasq-dhcp[7552]: DHCPOFFER(br-lan) 192.168.12.240 6c:40:08:9f:5b:bc
	Sat Apr 11 00:29:21 2020 daemon.info dnsmasq-dhcp[7552]: DHCPDISCOVER(br-lan) 6c:40:08:9f:5b:bc
	Sat Apr 11 00:29:21 2020 daemon.info dnsmasq-dhcp[7552]: DHCPOFFER(br-lan) 192.168.12.240 6c:40:08:9f:5b:bc
	Sat Apr 11 00:29:40 2020 daemon.notice hostapd: wlan0: AP-STA-DISCONNECTED 6c:40:08:9f:5b:bc
	Sat Apr 11 00:29:40 2020 daemon.info hostapd: wlan0: STA 6c:40:08:9f:5b:bc IEEE 802.11: disassociated
	Sat Apr 11 00:29:41 2020 daemon.info hostapd: wlan1: STA 6c:40:08:9f:5b:bc IEEE 802.11: authenticated
	Sat Apr 11 00:29:41 2020 daemon.info hostapd: wlan1: STA 6c:40:08:9f:5b:bc IEEE 802.11: associated (aid 8)
	Sat Apr 11 00:29:41 2020 daemon.notice hostapd: wlan1: AP-STA-CONNECTED 6c:40:08:9f:5b:bc
	Sat Apr 11 00:29:41 2020 daemon.info hostapd: wlan1: STA 6c:40:08:9f:5b:bc WPA: pairwise key handshake completed (RSN)
	Sat Apr 11 00:29:41 2020 daemon.info hostapd: wlan0: STA 6c:40:08:9f:5b:bc IEEE 802.11: deauthenticated due to inactivity (timer DEAUTH/REMOVE)
	Sat Apr 11 00:29:42 2020 daemon.info dnsmasq-dhcp[7552]: DHCPDISCOVER(br-lan) 6c:40:08:9f:5b:bc
	Sat Apr 11 00:29:42 2020 daemon.info dnsmasq-dhcp[7552]: DHCPOFFER(br-lan) 192.168.12.240 6c:40:08:9f:5b:bc
	Sat Apr 11 00:29:43 2020 daemon.info dnsmasq-dhcp[7552]: DHCPREQUEST(br-lan) 192.168.12.240 6c:40:08:9f:5b:bc
	Sat Apr 11 00:29:43 2020 daemon.info dnsmasq-dhcp[7552]: DHCPACK(br-lan) 192.168.12.240 6c:40:08:9f:5b:bc Scotts-MBP 

Log 2 - logread during connection with ethernet & subsequent disconnect

	Sat Apr 11 11:11:26 2020 daemon.info hostapd: wlan0: STA 6c:40:08:9f:5b:bc IEEE 802.11: authenticated
	Sat Apr 11 11:11:26 2020 daemon.info hostapd: wlan0: STA 6c:40:08:9f:5b:bc IEEE 802.11: associated (aid 1)
	Sat Apr 11 11:11:26 2020 daemon.notice hostapd: wlan0: AP-STA-CONNECTED 6c:40:08:9f:5b:bc
	Sat Apr 11 11:11:26 2020 daemon.info hostapd: wlan0: STA 6c:40:08:9f:5b:bc WPA: pairwise key handshake completed (RSN)
	Sat Apr 11 11:12:36 2020 daemon.info dnsmasq-dhcp[7552]: DHCPDISCOVER(br-lan) 5c:f7:e6:8b:bc:84
	Sat Apr 11 11:12:36 2020 daemon.info dnsmasq-dhcp[7552]: DHCPOFFER(br-lan) 192.168.12.154 5c:f7:e6:8b:bc:84
	Sat Apr 11 11:12:36 2020 daemon.info dnsmasq-dhcp[7552]: DHCPDISCOVER(br-lan) 5c:f7:e6:8b:bc:84
	Sat Apr 11 11:12:36 2020 daemon.info dnsmasq-dhcp[7552]: DHCPOFFER(br-lan) 192.168.12.154 5c:f7:e6:8b:bc:84
	Sat Apr 11 11:12:37 2020 daemon.info dnsmasq-dhcp[7552]: DHCPREQUEST(br-lan) 192.168.12.154 5c:f7:e6:8b:bc:84
	Sat Apr 11 11:12:37 2020 daemon.info dnsmasq-dhcp[7552]: DHCPACK(br-lan) 192.168.12.154 5c:f7:e6:8b:bc:84 Scotts-MBP
	Sat Apr 11 11:12:45 2020 daemon.info dnsmasq-dhcp[7552]: DHCPRELEASE(br-lan) 192.168.12.154 5c:f7:e6:8b:bc:84 
10.04.20202992KernelBug ReportVery LowMediumUSB problem on bcm6318 AllUnconfirmed Task Description

Hi
I’m using openwrt on bcm63xx bcm6318 sagemcom F@ST 2704N V1.
the router is actually V1.1 (16MB flash , 64MB RAM).
trying to connect a usb wifi dongle as AP

root@Openwrt:~# lsusb
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 002: ID 148f:5370 Ralink Technology, Corp. RT5370 Wireless Adapter
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

wlan1     Link encap:Ethernet  HWaddr 7C:DD:90:48:2A:D2  
          inet addr:192.168.2.1  Bcast:192.168.2.255  Mask:255.255.255.0
          inet6 addr: fe80::7edd:90ff:fe48:2ad2/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:955 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 B)  TX bytes:184246 (179.9 KiB)

the problem is that there’s no connectivity at all , I can connect to the AP (only without encryption ) and the ssid doesn’t always show on my mobile phone.
the usb port is working fine , I tried mounting a usb flash drive with no problem.
also the adapter is working , I tried it on Orange pi , Raspberrypi , bcm6328 , all with openwrt installed on them and didn’t have any problem .
I guess it is something related to bcm6318 or its architecture code .
the onboard broadcom pci wifi is working .
I suspected that its a power problem so I added an external usb power , but with same issues.
also I tried openwrt 19 ,18 ,17 with same problem.
I’m also using two bcm6328 routers as point to point wifi 5ghz link with Ralink RT5572 chipset ( rt2800usb driver ) withouyt any problem.
dmesg is filled with :

[ 1269.191198] rt2800usb_tx_sta_fifo_read_completed: 13054 callbacks suppressed
[ 1269.191239] ieee80211 phy1: rt2800usb_tx_sta_fifo_read_completed: Warning - TX status read failed -32
[ 1269.208421] ieee80211 phy1: rt2800usb_tx_sta_fifo_read_completed: Warning - TX status read failed -32
[ 1269.218373] ieee80211 phy1: rt2800usb_tx_sta_fifo_read_completed: Warning - TX status read failed -32
[ 1269.228285] ieee80211 phy1: rt2800usb_tx_sta_fifo_read_completed: Warning - TX status read failed -32
[ 1269.238151] ieee80211 phy1: rt2800usb_tx_sta_fifo_read_completed: Warning - TX status read failed -32
[ 1269.248029] ieee80211 phy1: rt2800usb_tx_sta_fifo_read_completed: Warning - TX status read failed -32
[ 1269.257902] ieee80211 phy1: rt2800usb_tx_sta_fifo_read_completed: Warning - TX status read failed -32
[ 1269.267793] ieee80211 phy1: rt2800usb_tx_sta_fifo_read_completed: Warning - TX status read failed -32
[ 1269.278183] ieee80211 phy1: rt2800usb_tx_sta_fifo_read_completed: Warning - TX status read failed -32
[ 1269.287995] ieee80211 phy1: rt2800usb_tx_sta_fifo_read_completed: Warning - TX status read failed -32

using rmmod to remove rt2800usb module results in kernel crash /sometimes hang and sometimes panic and reboot.

steps to reproduce:
-boot the router with usb wifi dongle
-configure it as access point and enable it
- dmesg log starts to fill and adapter is not working

10.04.20202991Base systemBug ReportVery LowLowUserland-only tarball to populate chrootTrunkUnconfirmed Task Description

Supply the following if possible:
- Device problem occurs on

ath79/mips

- Software versions of OpenWrt/LEDE release, packages, etc.

19.07.2

- Steps to reproduce

 Would be nice to have generic userland tarball also for less popular arches, for experiments involving a USB drive and facing the 'net


10.04.20202990Base systemBug ReportVery LowLowinvalid config-settings for linux5.4TrunkUnconfirmed Task Description

I was just building ath79-generic with having CONFIG_TESTING_KERNEL=y set.
During kernel-config the following message was seen:

net/sched/Kconfig:45: warning: menuconfig statement without prompt
.config:4076:warning: symbol value ‘m’ invalid for NF_CT_PROTO_GRE
.config:4106:warning: symbol value ‘m’ invalid for NF_NAT_REDIRECT

CALL    scripts/checksyscalls.sh

OpenWrt-commit is ae06a650d68026530beec4

 


10.04.20202989Base systemBug ReportVery LowCriticalBoots but no connection can be made to routerTrunkUnconfirmed Task Description

Hardware: ZBT WG3526 16MB RAM
Image file: openwrt-ramips-mt7621-zbtlink_zbt-wg3526-16m-squashfs-sysupgrade.bin
Image Date Stamp: Snapshot Fri Apr 10 06:55:59 2020

Issue: Flashes without issues.

		Boots but no connection can be made to router using web browser I/F, WinSCP or PuTTY.
		Not responding to ping 192.168.1.1.
		All LAN and WAN ports LED's are flashing.
		No Internet connection (WAN)
10.04.20202987Base systemBug ReportVery LowLowLEDs for WLAN and DSL do not work right.TrunkUnconfirmed Task Description

Supply the following if possible:
- Device problem occurs on VGV7510KW22 (o2 Box 6431)
- Software versions of OpenWrt: Trunk, snapshots,releases
- Steps to reproduce:
After boot the WLAN LED does not switch on when WLAN is running.
wifi down and wifi up then the WLAN LED does switch on.
After restarting the LED service the the WLAN LED and DSL LED does not switch back on.

/etc/init.d/led restart
setting up led wifi
setting up led dsl
setting up led internet

Internet LED works as expected.
My workaround for some years was to use netdev wlan0 as trigger.
After setting this I can’t change it back to the default setting phy0radio as this is not available in LUCI.

09.04.20202986Base systemBug ReportVery LowHighFunctionality broken by migration to DSA for Ubiquiti E...TrunkUnconfirmed Task Description

Supply the following if possible:
- Ubiquiti ER-X
- Trunk
- Build trunk of Openwrt and try to configure vlan enabled interfaces on an embedded switch.

Hi.

I have Ubiquiti ER-X which I have been using for quite a while and it was working just fine.
I was using it to route traffic from external internet connections to a ‘trunk’ port connected to a different OpenWrt device used as access point. So to clarify: I have one of the swich ports configured as ‘tagged’ (’tunk’) for multiple vlans.

Unfortunately commit 30644bc579e771e4b6dcc165ca966124e0259e1e that switched this device to use DSA for switch configuration have completely broken this setup.

And I’m not talking abut soft bricking - that was to be expected. Unfortunately DSA doesn’t provide functionality that was available in swconfig for years. Namely it seems to be impossible to configure switch ports to be ‘tagged’.

It looks like DSA is considered to be ‘the future’ but unfortunately it doesn’t see to be ready for prime time - it seems to be impossible to use DSA enabled devices in configurations that were perfectly possible before.

09.04.20202985Base systemBug ReportVery LowLowuci unbound forward zone portTrunkUnconfirmed Task Description

uci compile two different config options for unbound zone clause based on provided string value for list server.
If port is provided using ‘@’ charactes it assumes it’s a host rather than address and compile option to ' forward-host’.
It should be allow to use ‘@’ character in addition to IP address and compile option to ‘forward-addr’.

config zone

      list zone_name 'myzone.loc.'
      list server '10.1.0.2'
      list server '10.1.0.1'

compiles to

forward-zone:

name: myzone.loc.
forward-addr: 10.1.0.1@53
forward-addr: 10.1.0.2@53

config zone

      list zone_name 'myzone.loc.'
      list server '10.1.0.2@5053'
      list server '10.1.0.1@5053'

compiles to

forward-zone:

name: myzone.loc.
forward-host: 10.1.0.1@5053
forward-host: 10.1.0.2@5053

config zone

      list server '10.1.0.2'
      list server '10.1.0.1'

OpenWrt SNAPSHOT r12784-5562c5add2

09.04.20202984Base systemBug ReportVery LowLowImage file for ZBT-WG3526 (16M) wrong versionTrunkUnconfirmed Task Description

Device: ZBT-WG3526 (16M)

The image file for the ZBT-WG3526 (16M), zbtlink_zbt-wg3526-16m-squashfs-sysupgrade.bin dated Wednesday April 8, will flash but when rebooted puts the router in a boot loop.

The image file for the ZBT-WG3526 (16M), zbtlink_zbt-wg3526-16m-squashfs-sysupgrade.bin, is usually 4608.3 KB, as can be seen at releases/19.07.2/targets/ramips/mt7621/ but the April 8 image file is 5120.3 KB. The past 3 snapshots have all been 5120.3 KB in size and none have worked on my ZBT-WG3526 (16M).

09.04.20202983Base systemBug ReportVery LowLowAllow different mtu_fix settings for different interfac...TrunkUnconfirmed Task Description

My pppoe-wan has IPv4 (wan) and native IPv6 (wan_6) connections, I also have a 6to4-wan6 tunnel (native IPv6 from some ISPs can’t reach 6to4 addresses, additionally 6to4 normally offers faster connections to other 6to4 addresses). I want to enable mtu_fix for IPv4 only, but the option applies to all interfaces in the wan firewall zone (see ip6tables output below). Please make mtu_fix more granular so that different network interfaces (including virtual interfaces like wan_6) can have independent mtu_fix settings.

On a separate note, IPv4 iptables contains rules for 6to4 interface, is this a mistake? I don’t think IPv4 traffic could go through 6to4 interface.

If possible it would be good to add proto-41 firewall rule automatically when 6to4 is used, the rule is documented in the last part of https://openwrt.org/docs/guide-user/network/ipv6/barrier.breaker.ipv6.6to4 , the rule should really limit the scope to ipv4 family.

Chain FORWARD (policy ACCEPT 0 packets, 0 bytes)
 pkts bytes target     prot opt in     out     source               destination         
    0     0 TCPMSS     tcp      any    6to4-wan6  anywhere             anywhere             tcp flags:SYN,RST/SYN /* !fw3: Zone wan MTU fixing */ TCPMSS clamp to PMTU
    0     0 TCPMSS     tcp      any    pppoe-wan  anywhere             anywhere             tcp flags:SYN,RST/SYN /* !fw3: Zone wan MTU fixing */ TCPMSS clamp to PMTU
08.04.20202981Base systemBug ReportVery LowCriticalno switch0 device on Xiaomi Mi Router 3G (and V2)TrunkUnconfirmed Task Description

Apparently since kernel 5.4, the switch0 is not working correctly anymore. With a plain network config, ethernet ports are available. When using VLAN, the ports don’t work anymore; even the LEDs are off.
Luci → Network: no switch option available

root@test:/# swconfig list
root@test:/#


Devices: Xioami Mi Router 3G and Xiaomi Mi Router 3G V2
Tested with both devices. Tested with plain git checkout and my own build environment (master). Always the same behaviour...

boot log:

<## Booting image at bc180000 ...
   Image Name:   MIPS dl3it-mi3g Linux-5.4.28
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    2102189 Bytes =  2 MB
   Load Address: 80001000
   Entry Point:  80001000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
Erasing SPI Flash...
raspi_erase: offs:30000 len:10000
.
Writing to SPI Flash...
.
done
commandline uart_en=0 factory_mode=0 mem=128m root=/dev/mtdblock9
No initrd
## Transferring control to Linux (at address 80001000) ...
## Giving linux memsize in MB, 128

Starting kernel ...

[    0.000000] Linux version 5.4.28 (dl3it-mi3g@mySpace) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r12868-c948a4782b)) #0 SMP Wed Apr 8 13:05:51 2020
[    0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[    0.000000] printk: bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[    0.000000] MIPS: machine is Xiaomi Mi Router 3G v2
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] VPE topology {2,2} total 4
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000]   HighMem  empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] percpu: Embedded 14 pages/cpu s26480 r8192 d22672 u57344
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,jffs2
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    0.000000] Writing ErrCtl register=000400d0
[    0.000000] Readback ErrCtl register=000400d0
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 122004K/131072K available (5291K kernel code, 173K rwdata, 688K rodata, 1260K init, 224K bss, 9068K reserved, 0K cma-reserved, 0K highmem)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[    0.000000] NR_IRQS: 256
[    0.000000] random: get_random_bytes called from 0x80605a08 with crng_init=0
[    0.000000] CPU Clock: 880MHz
[    0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns
[    0.000009] sched_clock: 32 bits at 440MHz, resolution 2ns, wraps every 4880645118ns
[    0.007802] Calibrating delay loop... 583.68 BogoMIPS (lpj=1167360)
[    0.042004] pid_max: default: 32768 minimum: 301
[    0.046743] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.053968] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.063838] rcu: Hierarchical SRCU implementation.
[    0.069180] smp: Bringing up secondary CPUs ...
[    0.075309] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.075319] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.075331] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    0.075432] CPU1 revision is: 0001992f (MIPS 1004Kc)
[    0.101936] Synchronize counters for CPU 1: done.
[    0.142926] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.142934] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.142942] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    0.143000] CPU2 revision is: 0001992f (MIPS 1004Kc)
[    0.166600] Synchronize counters for CPU 2: done.
[    0.197977] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.197985] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.197994] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    0.198055] CPU3 revision is: 0001992f (MIPS 1004Kc)
[    0.224458] Synchronize counters for CPU 3: done.
[    0.254333] smp: Brought up 1 node, 4 CPUs
[    0.262078] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.271788] futex hash table entries: 1024 (order: 3, 32768 bytes, linear)
[    0.278766] pinctrl core: initialized pinctrl subsystem
[    0.285406] NET: Registered protocol family 16
[    0.310358] random: fast init done
[    0.318567] clocksource: Switched to clocksource GIC
[    0.325345] NET: Registered protocol family 2
[    0.330315] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[    0.338626] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.346200] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear)
[    0.353202] TCP: Hash tables configured (established 1024 bind 1024)
[    0.359629] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.366103] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.373226] NET: Registered protocol family 1
[    0.377532] PCI: CLS 0 bytes, default 32
[    0.470541] 4 CPUs re-calibrate udelay(lpj = 1163264)
[    0.477001] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[    0.492348] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.498111] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.510897] mt7621_gpio 1e000600.gpio: registering 32 gpios
[    0.516745] mt7621_gpio 1e000600.gpio: registering 32 gpios
[    0.522559] mt7621_gpio 1e000600.gpio: registering 32 gpios
[    0.528863] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
[    0.536441] printk: console [ttyS0] disabled
[    0.540734] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A
[    0.549720] printk: console [ttyS0] enabled
[    0.549720] printk: console [ttyS0] enabled
[    0.557980] printk: bootconsole [early0] disabled
[    0.557980] printk: bootconsole [early0] disabled
[    0.569760] spi-mt7621 1e000b00.spi: sys_freq: 220000000
[    0.577944] spi-nor spi0.0: gd25q128 (16384 Kbytes)
[    0.582936] 8 fixed-partitions partitions found on MTD device spi0.0
[    0.589281] Creating 8 MTD partitions on "spi0.0":
[    0.594079] 0x000000000000-0x000000030000 : "u-boot"
[    0.600206] 0x000000030000-0x000000040000 : "u-boot-env"
[    0.606677] 0x000000040000-0x000000050000 : "Bdata"
[    0.612654] 0x000000050000-0x000000060000 : "factory"
[    0.618871] 0x000000060000-0x000000070000 : "crash"
[    0.624841] 0x000000070000-0x000000080000 : "cfg_bak"
[    0.631048] 0x000000080000-0x000000180000 : "overlay"
[    0.637248] 0x000000180000-0x000001000000 : "firmware"
[    0.643805] 2 uimage-fw partitions found on MTD device firmware
[    0.649771] Creating 2 MTD partitions on "firmware":
[    0.654751] 0x000000000000-0x0000002013ed : "kernel"
[    0.660846] 0x0000002013ed-0x000000e80000 : "rootfs"
[    0.666945] mtd: device 9 (rootfs) set to be root filesystem
[    0.672703] 1 squashfs-split partitions found on MTD device rootfs
[    0.678890] 0x0000009c0000-0x000000e80000 : "rootfs_data"
[    0.686092] libphy: Fixed MDIO Bus: probed
[    0.716870] libphy: mdio: probed
[    0.720379] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
[    0.727570] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 21
[    0.738011] mt7621-pci 1e140000.pcie: Parsing DT failed
[    0.745444] NET: Registered protocol family 10
[    0.751473] Segment Routing with IPv6
[    0.755297] NET: Registered protocol family 17
[    0.760014] 8021q: 802.1Q VLAN Support v1.8
[    0.765966] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
[    1.374877] libphy: dsa slave smi: probed
[    1.438599] mt7530 mdio-bus:1f lan2 (uninitialized): PHY [dsa-0.0:02] driver [Generic PHY]
[    1.458608] mt7530 mdio-bus:1f lan1 (uninitialized): PHY [dsa-0.0:03] driver [Generic PHY]
[    1.478606] mt7530 mdio-bus:1f wan (uninitialized): PHY [dsa-0.0:04] driver [Generic PHY]
[    1.534553] mt7530 mdio-bus:1f: configuring for fixed/rgmii link mode
[    2.150548] mt7530 mdio-bus:1f: Link is Up - 1Gbps/Full - flow control off
[    2.226584] DSA: tree 0 setup
[    2.229877] rt2880-pinmux pinctrl: pcie is already enabled
[    2.235383] mt7621-pci 1e140000.pcie: Error applying setting, reverse things back
[    2.243000] mt7621-pci-phy 1e149000.pcie-phy: PHY for 0xbe149000 (dual port = 1)
[    2.250551] mt7621-pci-phy 1e14a000.pcie-phy: PHY for 0xbe14a000 (dual port = 0)
[    2.357677] mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz
[    2.363264] mt7621-pci-phy 1e14a000.pcie-phy: Xtal is 40MHz
[    2.468514] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK)
[    2.475474] mt7621-pci 1e140000.pcie: PCIE0 enabled
[    2.480348] mt7621-pci 1e140000.pcie: PCIE1 enabled
[    2.485228] mt7621-pci 1e140000.pcie: PCI coherence region base: 0x60000000, mask/settings: 0xf0000002
[    2.494703] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00
[    2.501072] pci_bus 0000:00: root bus resource [io  0x1e160000-0x1e16ffff]
[    2.507943] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[    2.514813] pci_bus 0000:00: root bus resource [bus 00-ff]
[    2.520334] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400
[    2.526365] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[    2.532635] pci 0000:00:00.0: reg 0x14: [mem 0x60400000-0x6040ffff]
[    2.538968] pci 0000:00:00.0: supports D1
[    2.542981] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[    2.549116] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400
[    2.555169] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[    2.561435] pci 0000:00:01.0: reg 0x14: [mem 0x60410000-0x6041ffff]
[    2.567758] pci 0000:00:01.0: supports D1
[    2.571771] pci 0000:00:01.0: PME# supported from D0 D1 D3hot
[    2.579056] pci 0000:01:00.0: [14c3:7662] type 00 class 0x028000
[    2.585128] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit]
[    2.591952] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[    2.598749] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[    2.606100] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[    2.611344] pci 0000:00:00.0:   bridge window [io  0x0000-0x0fff]
[    2.617432] pci 0000:00:00.0:   bridge window [mem 0x60000000-0x600fffff]
[    2.624216] pci 0000:00:00.0:   bridge window [mem 0x60100000-0x601fffff pref]
[    2.631434] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[    2.638265] pci 0000:02:00.0: [14c3:7603] type 00 class 0x028000
[    2.644325] pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x000fffff]
[    2.650726] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
[    2.658077] pci 0000:00:01.0: PCI bridge to [bus 02-ff]
[    2.663322] pci 0000:00:01.0:   bridge window [io  0x0000-0x0fff]
[    2.669410] pci 0000:00:01.0:   bridge window [mem 0x60200000-0x602fffff]
[    2.676194] pci 0000:00:01.0:   bridge window [mem 0x60300000-0x603fffff pref]
[    2.683420] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[    2.690083] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[    2.696693] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[    2.703651] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000]
[    2.710254] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000]
[    2.717213] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[    2.723998] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x601fffff pref]
[    2.731215] pci 0000:00:01.0: BAR 8: assigned [mem 0x60200000-0x602fffff]
[    2.737997] pci 0000:00:01.0: BAR 9: assigned [mem 0x60300000-0x603fffff pref]
[    2.745215] pci 0000:00:00.0: BAR 1: assigned [mem 0x60400000-0x6040ffff]
[    2.752006] pci 0000:00:01.0: BAR 1: assigned [mem 0x60410000-0x6041ffff]
[    2.758795] pci 0000:00:00.0: BAR 7: assigned [io  0x1e160000-0x1e160fff]
[    2.765577] pci 0000:00:01.0: BAR 7: assigned [io  0x1e161000-0x1e161fff]
[    2.772372] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit]
[    2.779687] pci 0000:01:00.0: BAR 6: assigned [mem 0x60100000-0x6010ffff pref]
[    2.786903] pci 0000:00:00.0: PCI bridge to [bus 01]
[    2.791867] pci 0000:00:00.0:   bridge window [io  0x1e160000-0x1e160fff]
[    2.798649] pci 0000:00:00.0:   bridge window [mem 0x60000000-0x600fffff]
[    2.805429] pci 0000:00:00.0:   bridge window [mem 0x60100000-0x601fffff pref]
[    2.812657] pci 0000:02:00.0: BAR 0: assigned [mem 0x60200000-0x602fffff]
[    2.819442] pci 0000:00:01.0: PCI bridge to [bus 02]
[    2.824405] pci 0000:00:01.0:   bridge window [io  0x1e161000-0x1e161fff]
[    2.831188] pci 0000:00:01.0:   bridge window [mem 0x60200000-0x602fffff]
[    2.837966] pci 0000:00:01.0:   bridge window [mem 0x60300000-0x603fffff pref]
[    2.845884] hctosys: unable to open rtc device (rtc0)
[    2.854774] VFS: Mounted root (squashfs filesystem) readonly on device 31:9.
[    2.865727] Freeing unused kernel memory: 1260K
[    2.870309] This architecture does not have kernel memory protection.
[    2.876743] Run /sbin/init as init process
[    3.287646] init: Console is alive
[    3.291282] init: - watchdog -
[    4.502146] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    4.642663] usbcore: registered new interface driver usbfs
[    4.648277] usbcore: registered new interface driver hub
[    4.653761] usbcore: registered new device driver usb
[    4.687605] SCSI subsystem initialized
[    4.700291] xhci-mtk 1e1c0000.xhci: 1e1c0000.xhci supply vbus not found, using dummy regulator
[    4.709018] xhci-mtk 1e1c0000.xhci: 1e1c0000.xhci supply vusb33 not found, using dummy regulator
[    4.717973] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
[    4.723320] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 1
[    4.738712] xhci-mtk 1e1c0000.xhci: hcc params 0x01401198 hci version 0x96 quirks 0x0000000000210010
[    4.747932] xhci-mtk 1e1c0000.xhci: irq 20, io mem 0x1e1c0000
[    4.754929] hub 1-0:1.0: USB hub found
[    4.758772] hub 1-0:1.0: 2 ports detected
[    4.763366] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
[    4.768728] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 2
[    4.776220] xhci-mtk 1e1c0000.xhci: Host supports USB 3.0 SuperSpeed
[    4.782759] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[    4.791649] hub 2-0:1.0: USB hub found
[    4.795501] hub 2-0:1.0: 1 port detected
[    4.806463] usbcore: registered new interface driver usb-storage
[    4.812799] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    4.830880] init: - preinit -
[    5.556493] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
[    5.564803] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[    5.573306] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[    5.758344] random: jshn: uninitialized urandom read (4 bytes read)
[    5.857508] random: jshn: uninitialized urandom read (4 bytes read)
[    5.892574] random: jshn: uninitialized urandom read (4 bytes read)
[    6.182562] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode
[    6.214670] 8021q: adding VLAN 0 to HW filter on device lan1
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[   10.454588] mt7530 mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control off
[   10.461993] IPv6: ADDRCONF(NETDEV_CHANGE): lan1: link becomes ready
[   10.497376] jffs2: notice: (593) jffs2_build_xattr_subsystem: complete building xattr subsystem, 12 of xdatum (10 unchecked, 2 orphan) and 14 of xref (2 dead, 0 orphan) found.
[   10.514983] mount_root: switching to jffs2 overlay
[   10.541029] overlayfs: upper fs does not support tmpfile.
[   10.553353] urandom-seed: Seeding with /etc/urandom.seed
[   10.710556] mt7530 mdio-bus:1f lan1: Link is Down
[   10.794276] procd: - early -
[   10.797283] procd: - watchdog -
[   11.390731] procd: - watchdog -
[   11.394174] procd: - ubus -
[   11.495821] urandom_read: 5 callbacks suppressed
[   11.495833] random: ubusd: uninitialized urandom read (4 bytes read)
[   11.508640] random: ubusd: uninitialized urandom read (4 bytes read)
[   11.516312] procd: - init -
Please press Enter to activate this console.
[   11.847029] random: crng init done
[   12.196458] kmodloader: loading kernel modules from /etc/modules.d/*
[   12.277843] Key type dns_resolver registered
[   12.294374] RPC: Registered named UNIX socket transport module.
[   12.300415] RPC: Registered udp transport module.
[   12.305113] RPC: Registered tcp transport module.
[   12.309806] RPC: Registered tcp NFSv4.1 backchannel transport module.
[   12.326652] tun: Universal TUN/TAP device driver, 1.6
[   12.343512] urngd: v1.0.2 started.
[   12.353986] NFS: Registering the id_resolver key type
[   12.359125] Key type id_resolver registered
[   12.363309] Key type id_legacy registered
[   12.409615] Loading modules backported from Linux version v5.4.27-0-g585e0cc08069
[   12.417142] Backport generated by backports.git v5.4.27-1-0-gf6e8852f
[   12.436131] wireguard: WireGuard 1.0.20200401 loaded. See www.wireguard.com for information.
[   12.444603] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
[   12.461355] xt_time: kernel timezone is -0000
[   12.526918] pci 0000:00:01.0: enabling device (0006 -> 0007)
[   12.532626] mt7603e 0000:02:00.0: enabling device (0000 -> 0002)
[   12.538852] mt7603e 0000:02:00.0: ASIC revision: 76030010
[   13.163810] mt7603e 0000:02:00.0: Firmware Version: ap_pcie
[   13.169406] mt7603e 0000:02:00.0: Build Time: 20160107100755
[   13.198554] mt7603e 0000:02:00.0: firmware init done
[   13.396912] pci 0000:00:00.0: enabling device (0006 -> 0007)
[   13.402664] mt76x2e 0000:01:00.0: enabling device (0000 -> 0002)
[   13.408975] mt76x2e 0000:01:00.0: ASIC revision: 76120044
[   13.890858] mt76x2e 0000:01:00.0: ROM patch build: 20141115060606a
[   13.905566] mt76x2e 0000:01:00.0: Firmware Version: 0.0.00
[   13.911181] mt76x2e 0000:01:00.0: Build: 1
[   13.915314] mt76x2e 0000:01:00.0: Build Time: 201507311614____
[   13.938667] mt76x2e 0000:01:00.0: Firmware running!
[   13.975037] kmodloader: done loading kernel modules from /etc/modules.d/*
[   19.857666] mtk_soc_eth 1e100000.ethernet eth0: Link is Down
[   20.437833] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
[   20.448515] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[   20.457303] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   20.470323] br-gast: port 1(eth0.119) entered blocking state
[   20.476130] br-gast: port 1(eth0.119) entered disabled state
[   20.482797] device eth0.119 entered promiscuous mode
[   20.487821] device eth0 entered promiscuous mode
[   20.496672] br-gast: port 1(eth0.119) entered blocking state
[   20.502388] br-gast: port 1(eth0.119) entered forwarding state
[   20.610001] br-iot: port 1(eth0.120) entered blocking state
[   20.615694] br-iot: port 1(eth0.120) entered disabled state
[   20.621937] device eth0.120 entered promiscuous mode
[   20.631403] br-iot: port 1(eth0.120) entered blocking state
[   20.637077] br-iot: port 1(eth0.120) entered forwarding state
[   20.756696] br-lan: port 1(eth0.117) entered blocking state
[   20.762433] br-lan: port 1(eth0.117) entered disabled state
[   20.769851] device eth0.117 entered promiscuous mode
[   20.780577] br-lan: port 1(eth0.117) entered blocking state
[   20.786261] br-lan: port 1(eth0.117) entered forwarding state
[   20.903708] br-media: port 1(eth0.118) entered blocking state
[   20.909789] br-media: port 1(eth0.118) entered disabled state
[   20.916212] device eth0.118 entered promiscuous mode
[   20.924455] br-media: port 1(eth0.118) entered blocking state
[   20.930260] br-media: port 1(eth0.118) entered forwarding state
[   21.021138] br-rapw: port 1(eth0.128) entered blocking state
[   21.027159] br-rapw: port 1(eth0.128) entered disabled state
[   21.033622] device eth0.128 entered promiscuous mode
[   21.042842] br-rapw: port 1(eth0.128) entered blocking state
[   21.048592] br-rapw: port 1(eth0.128) entered forwarding state
[   24.551924] br-lan: port 2(wlan1) entered blocking state
[   24.557320] br-lan: port 2(wlan1) entered disabled state
[   24.563518] device wlan1 entered promiscuous mode
[   24.640154] br-lan: port 3(wlan0) entered blocking state
[   24.645515] br-lan: port 3(wlan0) entered disabled state
[   24.651714] device wlan0 entered promiscuous mode
[   24.657070] br-lan: port 3(wlan0) entered blocking state
[   24.662453] br-lan: port 3(wlan0) entered forwarding state
[   25.927299] br-lan: port 3(wlan0) entered disabled state
[   25.933474] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[   25.940330] br-lan: port 2(wlan1) entered blocking state
[   25.945682] br-lan: port 2(wlan1) entered forwarding state
[   25.961147] br-gast: port 2(wlan1-1) entered blocking state
[   25.966815] br-gast: port 2(wlan1-1) entered disabled state
[   25.973281] device wlan1-1 entered promiscuous mode
[   25.980340] br-gast: port 2(wlan1-1) entered blocking state
[   25.986013] br-gast: port 2(wlan1-1) entered forwarding state
[   26.602100] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1-1: link becomes ready
[   26.615326] br-iot: port 2(wlan1-2) entered blocking state
[   26.620895] br-iot: port 2(wlan1-2) entered disabled state
[   26.627238] device wlan1-2 entered promiscuous mode
[   26.633956] br-iot: port 2(wlan1-2) entered blocking state
[   26.639547] br-iot: port 2(wlan1-2) entered forwarding state
[   26.654413] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   26.661418] br-lan: port 3(wlan0) entered blocking state
[   26.666839] br-lan: port 3(wlan0) entered forwarding state
[   26.684260] br-gast: port 3(wlan0-1) entered blocking state
[   26.689898] br-gast: port 3(wlan0-1) entered disabled state
[   26.696257] device wlan0-1 entered promiscuous mode
[   26.703570] br-gast: port 3(wlan0-1) entered blocking state
[   26.709197] br-gast: port 3(wlan0-1) entered forwarding state
[   26.950979] br-iot: port 2(wlan1-2) entered disabled state
[   26.958856] br-gast: port 3(wlan0-1) entered disabled state
[   27.183822] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1-2: link becomes ready
[   27.190950] br-iot: port 2(wlan1-2) entered blocking state
[   27.196513] br-iot: port 2(wlan1-2) entered forwarding state
[   27.287694] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0-1: link becomes ready
[   27.294743] br-gast: port 3(wlan0-1) entered blocking state
[   27.300358] br-gast: port 3(wlan0-1) entered forwarding state
[   27.314616] br-iot: port 3(wlan0-2) entered blocking state
[   27.320314] br-iot: port 3(wlan0-2) entered disabled state
[   27.326962] device wlan0-2 entered promiscuous mode
[   27.333493] br-iot: port 3(wlan0-2) entered blocking state
[   27.339125] br-iot: port 3(wlan0-2) entered forwarding state
[   27.763549] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0-2: link becomes ready
[   27.777443] br-rapw: port 2(wlan0-3) entered blocking state
[   27.783263] br-rapw: port 2(wlan0-3) entered disabled state
[   27.789570] device wlan0-3 entered promiscuous mode
[   27.796480] br-rapw: port 2(wlan0-3) entered blocking state
[   27.802127] br-rapw: port 2(wlan0-3) entered forwarding state
[   27.954752] br-rapw: port 2(wlan0-3) entered disabled state
[   28.219373] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0-3: link becomes ready
[   28.226593] br-rapw: port 2(wlan0-3) entered blocking state
[   28.232216] br-rapw: port 2(wlan0-3) entered forwarding state

kernel modules:

root@test:/# lsmod
cfg80211              258960  4 mt76x02_lib,mt7603e,mt76,mac80211
compat                   608  2 mac80211,cfg80211
crc_ccitt               1696  0
crc32c_generic          1376  0
dns_resolver            4272  1 nfsv4
ext4                  413584  0
fat                    58208  1 vfat
gpio_button_hotplug     6944  0
grace                   1328  1 lockd
ip_set                 25744 16 xt_set,ip_set_list_set,ip_set_hash_netportnet,ip_set_hash_netport,ip_set_hash_netnet,ip_set_hash_netiface,ip_set_hash_net,ip_set_hash_mac,ip_set_hash_ipportnet,ip_set_hash_ipportip,ip_set_hash_ipport,ip_set_hash_ipmark,ip_set_hash_ip,ip_set_bitmap_port,ip_set_bitmap_ipmac,ip_set_bitmap_ip
ip_set_bitmap_ip        6976  0
ip_set_bitmap_ipmac     7200  0
ip_set_bitmap_port      6176  0
ip_set_hash_ip         26176  0
ip_set_hash_ipmark     26400  0
ip_set_hash_ipport     26976  0
ip_set_hash_ipportip   28000  0
ip_set_hash_ipportnet   32576  0
ip_set_hash_mac        13632  0
ip_set_hash_net        29696  0
ip_set_hash_netiface   31264  0
ip_set_hash_netnet     32832  0
ip_set_hash_netport    31104  0
ip_set_hash_netportnet   33952  0
ip_set_list_set         7232  0
ip_tables              10848  3 iptable_nat,iptable_mangle,iptable_filter
ip6_tables             10624  2 ip6table_mangle,ip6table_filter
ip6_udp_tunnel          1760  1 wireguard
ip6t_REJECT             1248  2
ip6table_filter          704  1
ip6table_mangle         1184  1
ipt_REJECT              1184  2
iptable_filter           672  1
iptable_mangle           896  1
iptable_nat              768  1
jbd2                   56368  1 ext4
leds_gpio               3040  0
ledtrig_heartbeat       1520  0
ledtrig_usbport         2864  0
lockd                  55232  1 nfs
mac80211              496000  4 mt76x2e,mt76x02_lib,mt7603e,mt76
mbcache                 3952  1 ext4
mt76                   32096  4 mt76x2e,mt76x2_common,mt76x02_lib,mt7603e
mt7603e                38080  0
mt76x02_lib            39872  2 mt76x2e,mt76x2_common
mt76x2_common          11360  1 mt76x2e
mt76x2e                10080  0
nf_conntrack           71280  9 xt_state,xt_nat,xt_conntrack,xt_REDIRECT,xt_MASQUERADE,nf_nat,nf_flow_table,nf_conntrack_rtcache,nf_conntrack_netlink
nf_conntrack_netlink   24112  0
nf_conntrack_rtcache    2400  0
nf_defrag_ipv4          1120  1 nf_conntrack
nf_defrag_ipv6          4976  1 nf_conntrack
nf_flow_table          14864  2 xt_FLOWOFFLOAD,nf_flow_table_hw
nf_flow_table_hw        2416  1
nf_log_common           2624  2 nf_log_ipv4,nf_log_ipv6
nf_log_ipv4             3520  0
nf_log_ipv6             4192  0
nf_nat                 23056  4 iptable_nat,xt_nat,xt_REDIRECT,xt_MASQUERADE
nf_reject_ipv4          2112  1 ipt_REJECT
nf_reject_ipv6          2464  1 ip6t_REJECT
nfnetlink               4560  2 nf_conntrack_netlink,ip_set
nfs                   127680  1 nfsv4
nfsv4                 139152  0
nls_base                5424  6 vfat,fat,nls_utf8,nls_iso8859_1,nls_cp437,usbcore
nls_cp437               4416  0
nls_iso8859_1           2880  0
nls_utf8                 864  0
scsi_mod               86320  2 usb_storage,sd_mod
sd_mod                 29104  0
sunrpc                174064  3 nfsv4,nfs,lockd
swconfig                9680  0
tun                    32640  0
udp_tunnel              2560  1 wireguard
usb_common              2704  3 xhci_plat_hcd,xhci_hcd,usbcore
usb_storage            39888  0
usbcore               140176  6 ledtrig_usbport,usb_storage,xhci_plat_hcd,xhci_pci,xhci_mtk,xhci_hcd
vfat                   10016  0
wireguard              85792  0
x_tables               15472 24 xt_state,xt_nat,xt_conntrack,xt_REDIRECT,xt_MASQUERADE,xt_FLOWOFFLOAD,ipt_REJECT,xt_time,xt_tcpudp,xt_multiport,xt_mark,xt_mac,xt_limit,xt_comment,xt_TCPMSS,xt_LOG,iptable_mangle,iptable_filter,ip_tables,xt_set,ip6table_mangle,ip6table_filter,ip6_tables,ip6t_REJECT
xhci_hcd              113408  3 xhci_plat_hcd,xhci_pci,xhci_mtk
xhci_mtk                4800  0
xhci_pci                3424  0
xhci_plat_hcd           5600  0
xt_FLOWOFFLOAD          3152  0
xt_LOG                   768  0
xt_MASQUERADE            832  0
xt_REDIRECT              704  0
xt_TCPMSS               3168  2
xt_comment               512183
xt_conntrack            2432 24
xt_limit                1312  2
xt_mac                   640  0
xt_mark                  672  0
xt_multiport            1312  0
xt_nat                  2432  0
xt_set                  7328  0
xt_state                 832  0
xt_tcpudp               1824 18
xt_time                 1952  0
root@test:/#

Routers work fine with kernel 4.14.xxx

08.04.20202980Base systemBug ReportVery LowHighNo connection to Ethernet portTrunkUnconfirmed Task Description

Hi,
I can’t connect to my board with ethernet port, my chip is mt7688 and branch is master, I tested board with 19.07 branch, it seems all is OK.
Below are the logs with serial port :

root@OpenWrt:/# [  306.094979] mtk_soc_eth 10100000.ethernet eth0: transmit timed out
[  306.101270] mtk_soc_eth 10100000.ethernet eth0: dma_cfg:00000057
[  306.107392] mtk_soc_eth 10100000.ethernet eth0: tx_ring=0, base=0707c000, max=1024, ctx=1, dtx=0, fdx=0, next=1
[  306.117655] mtk_soc_eth 10100000.ethernet eth0: rx_ring=0, base=0701c000, max=1024, calc=0, drx=1
[  316.094980] mtk_soc_eth 10100000.ethernet eth0: transmit timed out
[  316.101273] mtk_soc_eth 10100000.ethernet eth0: dma_cfg:00000057
[  316.107393] mtk_soc_eth 10100000.ethernet eth0: tx_ring=0, base=0707c000, max=1024, ctx=1, dtx=0, fdx=0, next=1
[  316.117657] mtk_soc_eth 10100000.ethernet eth0: rx_ring=0, base=07070000, max=1024, calc=1023, drx=0
[  317.502718] rt3050-esw 10110000.esw: link changed 0x00
[  326.094981] mtk_soc_eth 10100000.ethernet eth0: transmit timed out
[  326.101274] mtk_soc_eth 10100000.ethernet eth0: dma_cfg:00000057
[  326.107394] mtk_soc_eth 10100000.ethernet eth0: tx_ring=0, base=0707c000, max=1024, ctx=2, dtx=0, fdx=0, next=2
[  326.117659] mtk_soc_eth 10100000.ethernet eth0: rx_ring=0, base=0701c000, max=1024, calc=1023, drx=0
[  336.094979] mtk_soc_eth 10100000.ethernet eth0: transmit timed out
[  336.101271] mtk_soc_eth 10100000.ethernet eth0: dma_cfg:00000057
[  336.107392] mtk_soc_eth 10100000.ethernet eth0: tx_ring=0, base=0707c000, max=1024, ctx=1, dtx=0, fdx=0, next=1
[  336.117656] mtk_soc_eth 10100000.ethernet eth0: rx_ring=0, base=07070000, max=1024, calc=1023, drx=0
[  346.094979] mtk_soc_eth 10100000.ethernet eth0: transmit timed out
[  346.101272] mtk_soc_eth 10100000.ethernet eth0: dma_cfg:00000057
[  346.107392] mtk_soc_eth 10100000.ethernet eth0: tx_ring=0, base=0707c000, max=1024, ctx=1, dtx=0, fdx=0, next=1
[  346.117654] mtk_soc_eth 10100000.ethernet eth0: rx_ring=0, base=0701c000, max=1024, calc=1023, drx=0
[  356.094981] mtk_soc_eth 10100000.ethernet eth0: transmit timed out
[  356.101273] mtk_soc_eth 10100000.ethernet eth0: dma_cfg:00000057
[  356.107393] mtk_soc_eth 10100000.ethernet eth0: tx_ring=0, base=0707c000, max=1024, ctx=1, dtx=0, fdx=0, next=1
[  356.117657] mtk_soc_eth 10100000.ethernet eth0: rx_ring=0, base=07070000, max=1024, calc=1023, drx=0
 


08.04.20202979Base systemBug ReportVery LowCriticalBanana Pi R64 can not upgrade on sysupgrade imageTrunkUnconfirmed Task Description

When I am try update initramfs image to sysupgrade. After command sysupgrade I am get error: Sysupgrade is not supported on your board yet.
Device: Banana PI R64
Build: Development Snapshot from Wed Apr 8 02:31:30 2020


08.04.20202978KernelBug ReportVery LowHighmt7621 snapshot downloads lack of .ko file in kernel mo...TrunkUnconfirmed Task Description

There is no .ko file in kernel module package, such as
kmod-crypto-acompress_5.4.28-1_mipsel_24kc.ipk
kmod-crypto-aead_5.4.28-1_mipsel_24kc.ipk
kmod-crypto-deflate_5.4.28-1_mipsel_24kc.ipk
Previous downloads in late 2019 and current mt7620 downloads do include .ko file.

07.04.20202977Base systemBug ReportVery LowHighParameters sendopts seems to be bad formated in the cal...openwrt-19.07Unconfirmed Task Description

The options parameters sendopts define in /etc/config/network seems to be badly formated in the call of the command odhcp6c

In /etc/config/network:

 

option sendopts “11:00 15:456544 16:1234”

is parsed like this (show via ps|grep odhcp6c)
-x11 00 -x15 456544 -x16 1234

The syntax given by the help of odhcp6c is different:

-x <opt>:<val> Add option opt (with value val) in sent packets (cumulative)

		Examples of IPv6 address, string and base-16 encoded options:
		-x dns:2001:2001::1,2001:2001::2 - option 23
		-x 15:office - option 15 (userclass)
		-x 0x1f4:ABBA - option 500
		-x 202:'"file"' - option 202

It appears than the : is replace by a space in the call of the command.
Regarding the help of the command, it should be :
-x 11:00 -x 15:456544 -x 16:1234

Thanks
Regards

06.04.20202974KernelBug ReportVery LowCriticalPhcomm K3 compiled with master branch has suffered a se...TrunkUnconfirmed Task Description

Phcomm K3 belongs to bcm53xx and USES the master branch to compile. Serious intermittent network interruption occurs, which is caused by mac80211!
Step by step troubleshooting found that the use of 19.07 branch of mac80211 source package compiled k3 firmware brush into the machine, everything is normal!


06.04.20202973KernelBug ReportVery LowCriticalPhcomm K3 belongs to bcm53xx, it is compiled using mast...TrunkUnconfirmed Task Description

Phcomm K3 belongs to bcm53xx and USES the master branch to compile. Serious intermittent network interruption occurs, which is caused by mac80211!
Step by step troubleshooting found that the use of 19.07 branch of mac80211 source package compiled k3 firmware brush into the machine, everything is normal!


06.04.20202972KernelBug ReportVery LowCriticalPhcomm K3 belongs to bcm53xx, which USES master branch ...TrunkUnconfirmed Task Description

Phcomm K3 belongs to bcm53xx and USES the master branch to compile. Serious intermittent network interruption occurs, which is caused by mac80211!
Step by step troubleshooting found that the use of 19.07 branch of mac80211 source package compiled k3 firmware brush into the machine, everything is normal!


05.04.20202968Base systemBug ReportVery LowLowwget/uclient issue, when using Basic AuthTrunkUnconfirmed Task Description

0.0.0.0 - - [05/Apr/2020:07:01:00 +0200] “GET /url.php HTTP/1.1” 401 681 “-” “uclient-fetch” 0.0.0.0 - user [05/Apr/2020:07:01:00 +0200] “GET /url.php HTTP/1.1” 200 358 “-” “uclient-fetch”

Reproducable at will, whenever Basic Auth used
wget –user=user –password=mypassword http://url.php

When using Basic Auth, wget/uclient-fetch first tries without credentials.
This might trigger intrusion protection on the server. And is a waste of bandwidth.


05.04.20202967Base systemBug ReportVery LowLowKernel msg "No memory allocated for crashlog" when boot...TrunkUnconfirmed Task Description

Whenever my Netgear r7500v2 running OpenWrt 19.07.2 is rebooted or power-cycled, the message ““No memory allocated for crashlog” is always shown in the kernel log.

If I try to simulate a kernel panic using “echo c > /proc/sysrq-trigger”, no crashlog is generated in /sys/kernel/debug/.

KERNEL LOG - Netgear r7500v2 running 19.07.2

[ 0.000000] Booting Linux on physical CPU 0×0 [ 0.000000] Linux version 4.14.171 (builder@buildhost) (gcc version 7.5.0 (OpenWrt GCC 7.5.0 r10947-65030d81f3)) #0 SMP Thu Feb 27 21:05:12 2020
[ 0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5787d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[ 0.000000] OF: fdt: Machine model: Netgear Nighthawk X4 R7500v2
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] On node 0 totalpages: 122880
[ 0.000000] free_area_init_node: node 0, pgdat c0a27880, node_mem_map dda39000
[ 0.000000] Normal zone: 960 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 122880 pages, LIFO batch:31
[ 0.000000] random: get_random_bytes called from 0xc09008dc with crng_init=0
[ 0.000000] percpu: Embedded 15 pages/cpu s29388 r8192 d23860 u61440
[ 0.000000] pcpu-alloc: s29388 r8192 d23860 u61440 alloc=15*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 121920
[ 0.000000] Kernel command line: rootfstype=squashfs noinitrd
[ 0.000000] Bootloader command line (ignored): console=ttyHSL1,115200n8
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 477380K/491520K available (4975K kernel code, 160K rwdata, 756K rodata, 1024K init, 235K bss, 14140K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xde800000 - 0xff800000 ( 528 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xde000000 ( 480 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0208000 - 0xc07dbe98 (5968 kB)
[ 0.000000] .init : 0xc0900000 - 0xc0a00000 (1024 kB)
[ 0.000000] .data : 0xc0a00000 - 0xc0a28180 ( 161 kB)
[ 0.000000] .bss : 0xc0a2a000 - 0xc0a64e18 ( 236 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] clocksource: dg_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 305801671480 ns
[ 0.000008] sched_clock: 32 bits at 6MHz, resolution 160ns, wraps every 343597383600ns
[ 0.000022] Switching to timer-based delay loop, resolution 160ns
[ 0.000229] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.50 BogoMIPS (lpj=62500)
[ 0.000255] pid_max: default: 32768 minimum: 301
[ 0.000382] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000400] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000916] CPU: Testing write buffer coherency: ok
[ 0.001695] Setting up static identity map for 0×42300000 - 0×42300060 [ 0.001848] Hierarchical SRCU implementation.
[ 0.002590] smp: Bringing up secondary CPUs ...
[ 0.004399] smp: Brought up 1 node, 2 CPUs
[ 0.004416] SMP: Total of 2 processors activated (25.00 BogoMIPS).
[ 0.004426] CPU: All CPU(s) started in SVC mode.
[ 0.014357] VFP support v0.3: implementor 51 architecture 64 part 4d variant 2 rev 0
[ 0.014521] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.014549] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.014656] pinctrl core: initialized pinctrl subsystem
[ 0.015648] NET: Registered protocol family 16
[ 0.015944] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.017300] cpuidle: using governor ladder
[ 0.017369] cpuidle: using governor menu
[ 0.039972] msm_bus_fabric_init_driver
[ 0.041523] usbcore: registered new interface driver usbfs
[ 0.041604] usbcore: registered new interface driver hub
[ 0.041691] usbcore: registered new device driver usb
[ 0.041748] pps_core: LinuxPPS API ver. 1 registered
[ 0.041760] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti giometti@linux.it [ 0.041792] PTP clock support registered
[ 0.043547] clocksource: Switched to clocksource dg_timer
[ 0.046802] NET: Registered protocol family 2
[ 0.047409] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.047450] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.047506] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.047600] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.047627] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.047808] NET: Registered protocol family 1
[ 0.047855] PCI: CLS 0 bytes, default 64
[ 0.049026] No memory allocated for crashlog
[ 0.049301] workingset: timestamp_bits=30 max_order=17 bucket_order=0
[ 0.054475] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.054494] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) © 2001-2006 Red Hat, Inc.
[ 0.061135] io scheduler noop registered
[ 0.061154] io scheduler deadline registered (default)
[ 0.062800] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda not found, using dummy regulator
[ 0.062919] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda_phy not found, using dummy regulator
[ 0.063022] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda_refclk not found, using dummy regulator
[ 0.063756] OF: PCI: host bridge /soc/pci@1b500000 ranges:
[ 0.063800] OF: PCI: IO 0x0fe00000..0x0fefffff → 0x0fe00000
[ 0.063824] OF: PCI: MEM 0×08000000..0x0fdfffff → 0×08000000 [ 0.172087] qcom-pcie 1b500000.pci: link up
[ 0.172252] qcom-pcie 1b500000.pci: PCI host bridge to bus 0000:00
[ 0.172276] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.172298] pci_bus 0000:00: root bus resource [io 0×0000-0xfffff] (bus address [0xfe00000-0xfefffff])
[ 0.172313] pci_bus 0000:00: root bus resource [mem 0×08000000-0x0fdfffff]
[ 0.172330] pci_bus 0000:00: scanning bus
[ 0.172376] pci 0000:00:00.0: [17cb:0101] type 01 class 0×060400 [ 0.172463] pci 0000:00:00.0: calling 0xc030d3c0
[ 0.172533] pci 0000:00:00.0: supports D1
[ 0.172544] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 0.172560] pci 0000:00:00.0: PME# disabled
[ 0.172816] pci_bus 0000:00: fixups for bus
[ 0.172839] PCI: bus0: Fast back to back transfers disabled
[ 0.172859] pci 0000:00:00.0: scanning [bus 01-ff] behind bridge, pass 0
[ 0.172987] pci_bus 0000:01: scanning bus
[ 0.173164] pci 0000:01:00.0: [168c:0040] type 00 class 0×028000 [ 0.173515] pci 0000:01:00.0: reg 0×10: [mem 0×00000000-0x001fffff 64bit]
[ 0.174088] pci 0000:01:00.0: calling 0xc030d3c0
[ 0.174731] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[ 0.174773] pci 0000:01:00.0: PME# disabled
[ 0.175109] pci_bus 0000:01: fixups for bus
[ 0.175180] PCI: bus1: Fast back to back transfers disabled
[ 0.175198] pci_bus 0000:01: bus scan returning with max=01
[ 0.175216] pci 0000:00:00.0: scanning [bus 01-ff] behind bridge, pass 1
[ 0.175233] pci_bus 0000:00: bus scan returning with max=ff
[ 0.175284] pci 0000:00:00.0: BAR 8: assigned [mem 0×08000000-0x081fffff]
[ 0.175309] pci 0000:01:00.0: BAR 0: assigned [mem 0×08000000-0x081fffff 64bit]
[ 0.175439] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 0.175462] pci 0000:00:00.0: bridge window [mem 0×08000000-0x081fffff]
[ 0.175496] pci 0000:00:00.0: calling 0xc055fae4
[ 0.175691] pcieport 0000:00:00.0: assign IRQ: got 67
[ 0.176013] pcieport 0000:00:00.0: AER enabled with IRQ 35
[ 0.176129] pci 0000:01:00.0: calling 0xc055fae4
[ 0.176546] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda not found, using dummy regulator
[ 0.176666] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda_phy not found, using dummy regulator
[ 0.176761] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda_refclk not found, using dummy regulator
[ 0.177458] OF: PCI: host bridge /soc/pci@1b700000 ranges:
[ 0.177495] OF: PCI: IO 0x31e00000..0x31efffff → 0x31e00000
[ 0.177520] OF: PCI: MEM 0x2e000000..0x31dfffff → 0x2e000000
[ 0.287453] qcom-pcie 1b700000.pci: link up
[ 0.287604] qcom-pcie 1b700000.pci: PCI host bridge to bus 0001:00
[ 0.287625] pci_bus 0001:00: root bus resource [bus 00-ff]
[ 0.287641] pci_bus 0001:00: root bus resource [mem 0x2e000000-0x31dfffff]
[ 0.287655] pci_bus 0001:00: scanning bus
[ 0.287697] pci 0001:00:00.0: [17cb:0101] type 01 class 0×060400 [ 0.287769] pci 0001:00:00.0: calling 0xc030d3c0
[ 0.287830] pci 0001:00:00.0: supports D1
[ 0.287839] pci 0001:00:00.0: PME# supported from D0 D1 D3hot
[ 0.287854] pci 0001:00:00.0: PME# disabled
[ 0.288092] pci_bus 0001:00: fixups for bus
[ 0.288110] PCI: bus0: Fast back to back transfers disabled
[ 0.288128] pci 0001:00:00.0: scanning [bus 01-ff] behind bridge, pass 0
[ 0.288247] pci_bus 0001:01: scanning bus
[ 0.288434] pci 0001:01:00.0: [168c:0040] type 00 class 0×028000 [ 0.288807] pci 0001:01:00.0: reg 0×10: [mem 0×00000000-0x001fffff 64bit]
[ 0.289305] pci 0001:01:00.0: calling 0xc030d3c0
[ 0.289996] pci 0001:01:00.0: PME# supported from D0 D3hot D3cold
[ 0.290041] pci 0001:01:00.0: PME# disabled
[ 0.290384] pci_bus 0001:01: fixups for bus
[ 0.290460] PCI: bus1: Fast back to back transfers disabled
[ 0.290475] pci_bus 0001:01: bus scan returning with max=01
[ 0.290491] pci 0001:00:00.0: scanning [bus 01-ff] behind bridge, pass 1
[ 0.290508] pci_bus 0001:00: bus scan returning with max=ff
[ 0.290544] pci 0001:00:00.0: BAR 8: assigned [mem 0x2e000000-0x2e1fffff]
[ 0.290568] pci 0001:01:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit]
[ 0.290700] pci 0001:00:00.0: PCI bridge to [bus 01-ff]
[ 0.290722] pci 0001:00:00.0: bridge window [mem 0x2e000000-0x2e1fffff]
[ 0.290752] pci 0001:00:00.0: calling 0xc055fae4
[ 0.290933] pcieport 0001:00:00.0: assign IRQ: got 100
[ 0.291229] pcieport 0001:00:00.0: AER enabled with IRQ 68
[ 0.291338] pci 0001:01:00.0: calling 0xc055fae4
[ 0.293608] L2 @ QSB rate. Forcing new rate.
[ 0.293943] L2 @ 384000 KHz
[ 0.294121] CPU0 @ 800000 KHz
[ 0.294134] CPU1 @ QSB rate. Forcing new rate.
[ 0.294260] CPU1 @ 384000 KHz
[ 0.298165] gsbi 16300000.gsbi: GSBI port protocol: 6 crci: 0
[ 0.300055] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.302639] msm_serial 16340000.serial: msm_serial: detected port #0
[ 0.302736] msm_serial 16340000.serial: uartclk = 7372800
[ 0.302820] 16340000.serial: ttyMSM0 at MMIO 0×16340000 (irq = 101, base_baud = 460800) is a MSM
[ 0.302857] msm_serial: console setup on port #0
[ 1.025206] console [ttyMSM0] enabled
[ 1.029901] msm_serial: driver initialized
[ 1.038615] loop: module loaded
[ 1.040683] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xa1
[ 1.040714] nand: Micron MT29F1G08ABBEAH4
[ 1.047271] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 1.051179] 8 fixed-partitions partitions found on MTD device qcom_nand.0
[ 1.058606] Creating 8 MTD partitions on “qcom_nand.0”:
[ 1.065491] 0×000000000000-0x000000c80000 : “qcadata” [ 1.075531] random: fast init done
[ 1.093285] 0x000000c80000-0×000001180000 : “APPSBL” [ 1.102841] 0×000001180000-0×000001200000 : “APPSBLENV” [ 1.104548] 0×000001200000-0×000001340000 : “art” [ 1.109810] 0×000001340000-0×000001480000 : “artbak” [ 1.114731] 0×000001480000-0×000001880000 : “kernel” [ 1.124591] 0×000001880000-0×000007900000 : “ubi” [ 1.293621] 0×000007900000-0×000008000000 : “reserve” [ 1.307906] libphy: GPIO Bitbanged MDIO: probed
[ 1.329381] switch0: Atheros AR8337 rev. 2 switch registered on gpio-0
[ 2.176103] ar8327: qca,phy-rgmii-en is not specified
[ 2.176492] libphy: Fixed MDIO Bus: probed
[ 2.182240] ipq806x-gmac-dwmac 37200000.ethernet: PTP uses main clock
[ 2.184529] stmmac - user ID: 0×10, Synopsys ID: 0×37 [ 2.190647] ipq806x-gmac-dwmac 37200000.ethernet: Ring mode enabled
[ 2.195757] ipq806x-gmac-dwmac 37200000.ethernet: DMA HW capability register supported
[ 2.201760] ipq806x-gmac-dwmac 37200000.ethernet: Enhanced/Alternate descriptors
[ 2.209805] ipq806x-gmac-dwmac 37200000.ethernet: Enabled extended descriptors
[ 2.217364] ipq806x-gmac-dwmac 37200000.ethernet: RX Checksum Offload Engine supported
[ 2.224395] ipq806x-gmac-dwmac 37200000.ethernet: COE Type 2
[ 2.232224] ipq806x-gmac-dwmac 37200000.ethernet: TX Checksum insertion supported
[ 2.238106] ipq806x-gmac-dwmac 37200000.ethernet: Wake-Up On Lan supported
[ 2.245484] ipq806x-gmac-dwmac 37200000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 2.253897] ipq806x-gmac-dwmac 37400000.ethernet: PTP uses main clock
[ 2.260973] stmmac - user ID: 0×10, Synopsys ID: 0×37 [ 2.267198] ipq806x-gmac-dwmac 37400000.ethernet: Ring mode enabled
[ 2.272156] ipq806x-gmac-dwmac 37400000.ethernet: DMA HW capability register supported
[ 2.278315] ipq806x-gmac-dwmac 37400000.ethernet: Enhanced/Alternate descriptors
[ 2.286278] ipq806x-gmac-dwmac 37400000.ethernet: Enabled extended descriptors
[ 2.293836] ipq806x-gmac-dwmac 37400000.ethernet: RX Checksum Offload Engine supported
[ 2.300803] ipq806x-gmac-dwmac 37400000.ethernet: COE Type 2
[ 2.308771] ipq806x-gmac-dwmac 37400000.ethernet: TX Checksum insertion supported
[ 2.314583] ipq806x-gmac-dwmac 37400000.ethernet: Wake-Up On Lan supported
[ 2.321898] ipq806x-gmac-dwmac 37400000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 2.329412] i2c /dev entries driver
[ 2.338177] Calibration not found.
[ 2.341644] Speed bin: 0
[ 2.344021] PVS bin: 1
[ 2.347907] cpuidle: enable-method property ‘qcom,kpss-acc-v1’ found operations
[ 2.348868] cpuidle: enable-method property ‘qcom,kpss-acc-v1’ found operations
[ 2.356707] sdhci: Secure Digital Host Controller Interface driver
[ 2.363298] sdhci: Copyright© Pierre Ossman
[ 2.369627] sdhci-pltfm: SDHCI platform and OF driver helper
[ 2.375443] NET: Registered protocol family 10
[ 2.381101] Segment Routing with IPv6
[ 2.384127] NET: Registered protocol family 17
[ 2.387743] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 2.392700] 8021q: 802.1Q VLAN Support v1.8
[ 2.405292] Registering SWP/SWPB emulation handler
[ 2.421323] qcom_rpm 108000.rpm: RPM firmware 3.0.16777342
[ 2.432804] s1a: supplied by regulator-dummy
[ 2.432906] s1a: Bringing 0uV into 1050000-1050000uV
[ 2.436504] s1b: supplied by regulator-dummy
[ 2.441137] s1b: Bringing 0uV into 1050000-1050000uV
[ 2.445691] s2a: supplied by regulator-dummy
[ 2.450341] s2a: Bringing 0uV into 800000-800000uV
[ 2.454857] s2b: supplied by regulator-dummy
[ 2.459202] s2b: Bringing 0uV into 800000-800000uV
[ 2.468388] UBI: auto-attach mtd6
[ 2.468420] ubi0: attaching mtd6
[ 2.519756] random: crng init done
[ 3.203591] ubi0: scanning is finished
[ 3.213668] ubi0: attached mtd6 (name “ubi”, size 96 MiB)
[ 3.213689] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 3.218037] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 3.224890] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 3.231665] ubi0: good PEBs: 772, bad PEBs: 0, corrupted PEBs: 0
[ 3.238497] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[ 3.244746] ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 152459084
[ 3.251722] ubi0: available PEBs: 0, total reserved PEBs: 772, PEBs reserved for bad PEB handling: 20
[ 3.260811] ubi0: background thread “ubi_bgt0d” started, PID 59
[ 3.261484] block ubiblock0_0: created from ubi0:0(rootfs)
[ 3.275831] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[ 3.281321] hctosys: unable to open rtc device (rtc0)
[ 3.293054] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 3.294855] Freeing unused kernel memory: 1024K
[ 3.733321] init: Console is alive
[ 3.733456] init: - watchdog -
[ 4.288846] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 4.400142] ehci_hcd: USB 2.0 ‘Enhanced’ Host Controller (EHCI) Driver
[ 4.403625] SCSI subsystem initialized
[ 4.410050] libata version 3.00 loaded.
[ 4.413158] ahci 29000000.sata: forcing port_map 0×0 → 0×1 [ 4.413230] ahci 29000000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0×1 impl platform mode
[ 4.417662] ahci 29000000.sata: flags: ncq sntf pm led clo only pmp pio slum part ccc apst
[ 4.427114] scsi host0: ahci
[ 4.434724] ata1: SATA max UDMA/133 mmio [mem 0×29000000-0x2900017f] port 0×100 irq 26
[ 4.766181] ata1: SATA link down (SStatus 0 SControl 300)
[ 4.769356] ehci-platform: EHCI generic platform driver
[ 4.776396] ohci_hcd: USB 1.1 ‘Open’ Host Controller (OHCI) Driver
[ 4.777280] ohci-platform: OHCI generic platform driver
[ 4.910368] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 4.910459] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 4.915181] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f065 hci version 0×100 quirks 0×0000000002010010 [ 4.922400] xhci-hcd xhci-hcd.0.auto: irq 105, io mem 0×11000000 [ 4.932480] hub 1-0:1.0: USB hub found
[ 4.938104] hub 1-0:1.0: 1 port detected
[ 4.941701] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 4.945658] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 4.950867] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
[ 4.958583] usb usb2: We don’t know the algorithms for LPM for this host, disabling LPM.
[ 4.965444] hub 2-0:1.0: USB hub found
[ 4.973368] hub 2-0:1.0: 1 port detected
[ 4.977232] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 4.980996] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
[ 4.986504] xhci-hcd xhci-hcd.1.auto: hcc params 0x0228f065 hci version 0×100 quirks 0×0000000002010010 [ 4.993931] xhci-hcd xhci-hcd.1.auto: irq 106, io mem 0×10000000 [ 5.003612] hub 3-0:1.0: USB hub found
[ 5.009566] hub 3-0:1.0: 1 port detected
[ 5.013216] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 5.017156] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
[ 5.022396] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
[ 5.030118] usb usb4: We don’t know the algorithms for LPM for this host, disabling LPM.
[ 5.036981] hub 4-0:1.0: USB hub found
[ 5.044986] hub 4-0:1.0: 1 port detected
[ 5.050128] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 5.057984] init: - preinit -
[ 6.781373] Generic PHY fixed-0:01: attached PHY driver [Generic PHY] (mii_bus:phy_addr=fixed-0:01, irq=POLL)
[ 6.783007] dwmac1000: Master AXI performs any burst length
[ 6.790440] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[ 6.795942] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
[ 6.805639] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 7.833932] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[ 7.834011] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 10.029570] UBIFS (ubi0:1): background thread “ubifs_bgt0_1” started, PID 143
[ 10.101636] UBIFS (ubi0:1): recovery needed
[ 10.227770] UBIFS (ubi0:1): recovery completed
[ 10.227843] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name “rootfs_data” [ 10.231099] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 10.239072] UBIFS (ubi0:1): FS size: 90279936 bytes (86 MiB, 711 LEBs), journal size 4571136 bytes (4 MiB, 36 LEBs)
[ 10.248974] UBIFS (ubi0:1): reserved for root: 4264143 bytes (4164 KiB)
[ 10.259189] UBIFS (ubi0:1): media format: w4/r0 (latest is w5/r0), UUID E2C3B09D-9870-41F3-A16D-83335278F48C, small LPT model
[ 10.281904] mount_root: switching to ubifs overlay
[ 10.301239] urandom-seed: Seeding with /etc/urandom.seed
[ 10.471541] procd: - early -
[ 10.471670] procd: - watchdog -
[ 11.142803] procd: - watchdog -
[ 11.143313] procd: - ubus -
[ 11.237156] procd: - init -
[ 11.650168] urngd: v1.0.2 started.
[ 11.676844] kmodloader: loading kernel modules from /etc/modules.d/*
[ 11.681488] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 11.686329] Loading modules backported from Linux version v4.19.98-0-gd183c8e2647a
[ 11.687554] Backport generated by backports.git v4.19.98-1-0-g8204eb99
[ 11.695962] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 11.704177] nf_conntrack version 0.5.0 (8192 buckets, 32768 max)
[ 11.761069] wireguard: WireGuard 0.0.20190702 loaded. See www.wireguard.com for information.
[ 11.761112] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld Jason@zx2c4.com. All Rights Reserved.
[ 11.773657] xt_time: kernel timezone is -0000
[ 11.804583] PPP generic driver version 2.4.2
[ 11.805557] NET: Registered protocol family 24
[ 11.815317] ath10k_pci 0000:01:00.0: assign IRQ: got 67
[ 11.815340] ath10k 4.19 driver, optimized for CT firmware, probing pci device: 0×40.
[ 11.815747] ath10k_pci 0000:01:00.0: enabling device (0140 → 0142)
[ 11.822199] ath10k_pci 0000:01:00.0: enabling bus mastering
[ 11.822659] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[ 11.998510] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/fwcfg-pci-0000:01:00.0.txt failed with error -2
[ 11.998556] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 12.091038] firmware ath10k!fwcfg-pci-0000:01:00.0.txt: firmware_loading_store: map pages failed
[ 12.093273] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA99X0/hw2.0/ct-firmware-5.bin failed with error -2
[ 12.098991] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 12.133002] firmware ath10k!QCA99X0!hw2.0!ct-firmware-5.bin: firmware_loading_store: map pages failed
[ 12.133222] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA99X0/hw2.0/ct-firmware-2.bin failed with error -2
[ 12.141301] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 12.170070] firmware ath10k!QCA99X0!hw2.0!ct-firmware-2.bin: firmware_loading_store: map pages failed
[ 12.170327] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA99X0/hw2.0/firmware-6.bin failed with error -2
[ 12.178375] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 12.205811] firmware ath10k!QCA99X0!hw2.0!firmware-6.bin: firmware_loading_store: map pages failed
[ 12.475389] ath10k_pci 0000:01:00.0: qca99x0 hw2.0 target 0×01000000 chip_id 0x003b01ff sub 168c:0002
[ 12.475452] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[ 12.489548] ath10k_pci 0000:01:00.0: firmware ver 10.4b-ct-9980-fW-012-17ba9833 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 0fb1435e
[ 12.556781] ath10k_pci 0000:01:00.0: board_file api 2 bmi_id 1:1 crc32 08fa09f2
[ 13.742806] ath10k_pci 0000:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
[ 13.742836] ath10k_pci 0000:01:00.0: msdu-desc: 2500 skid: 32
[ 13.818824] ath10k_pci 0000:01:00.0: wmi print ‘P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0’ [ 13.819600] ath10k_pci 0000:01:00.0: wmi print ‘free: 34244 iram: 32964 sram: 6508’ [ 14.061437] ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1
[ 14.166375] ath: EEPROM regdomain: 0×0 [ 14.166390] ath: EEPROM indicates default country code should be used
[ 14.166400] ath: doing EEPROM country→regdmn map search
[ 14.166418] ath: country maps to regdmn code: 0x3a
[ 14.166431] ath: Country alpha2 being used: US
[ 14.166442] ath: Regpair used: 0x3a
[ 14.171923] ath10k_pci 0001:01:00.0: assign IRQ: got 100
[ 14.171965] ath10k 4.19 driver, optimized for CT firmware, probing pci device: 0×40.
[ 14.173040] ath10k_pci 0001:01:00.0: enabling device (0140 → 0142)
[ 14.179020] ath10k_pci 0001:01:00.0: enabling bus mastering
[ 14.179701] ath10k_pci 0001:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[ 14.355448] ath10k_pci 0001:01:00.0: Direct firmware load for ath10k/fwcfg-pci-0001:01:00.0.txt failed with error -2
[ 14.355481] ath10k_pci 0001:01:00.0: Falling back to user helper
[ 14.537604] firmware ath10k!fwcfg-pci-0001:01:00.0.txt: firmware_loading_store: map pages failed
[ 14.540007] ath10k_pci 0001:01:00.0: Direct firmware load for ath10k/QCA99X0/hw2.0/ct-firmware-5.bin failed with error -2
[ 14.545575] ath10k_pci 0001:01:00.0: Falling back to user helper
[ 14.588731] firmware ath10k!QCA99X0!hw2.0!ct-firmware-5.bin: firmware_loading_store: map pages failed
[ 14.588988] ath10k_pci 0001:01:00.0: Direct firmware load for ath10k/QCA99X0/hw2.0/ct-firmware-2.bin failed with error -2
[ 14.597028] ath10k_pci 0001:01:00.0: Falling back to user helper
[ 14.630325] firmware ath10k!QCA99X0!hw2.0!ct-firmware-2.bin: firmware_loading_store: map pages failed
[ 14.630506] ath10k_pci 0001:01:00.0: Direct firmware load for ath10k/QCA99X0/hw2.0/firmware-6.bin failed with error -2
[ 14.638635] ath10k_pci 0001:01:00.0: Falling back to user helper
[ 14.695699] firmware ath10k!QCA99X0!hw2.0!firmware-6.bin: firmware_loading_store: map pages failed
[ 14.695869] ath10k_pci 0001:01:00.0: qca99x0 hw2.0 target 0×01000000 chip_id 0x003b01ff sub 168c:0002
[ 14.703563] ath10k_pci 0001:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[ 14.715193] ath10k_pci 0001:01:00.0: firmware ver 10.4b-ct-9980-fW-012-17ba9833 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 0fb1435e
[ 14.785906] ath10k_pci 0001:01:00.0: board_file api 2 bmi_id 1:2 crc32 08fa09f2
[ 15.975146] ath10k_pci 0001:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
[ 15.975173] ath10k_pci 0001:01:00.0: msdu-desc: 2500 skid: 32
[ 16.052629] ath10k_pci 0001:01:00.0: wmi print ‘P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0’ [ 16.053436] ath10k_pci 0001:01:00.0: wmi print ‘free: 34244 iram: 32964 sram: 6508’ [ 16.272699] ath10k_pci 0001:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1
[ 16.396873] ath: EEPROM regdomain: 0×0 [ 16.396889] ath: EEPROM indicates default country code should be used
[ 16.396899] ath: doing EEPROM country→regdmn map search
[ 16.396916] ath: country maps to regdmn code: 0x3a
[ 16.396931] ath: Country alpha2 being used: US
[ 16.396942] ath: Regpair used: 0x3a
[ 16.405823] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 19.924371] Generic PHY fixed-0:01: attached PHY driver [Generic PHY] (mii_bus:phy_addr=fixed-0:01, irq=POLL)
[ 19.925264] dwmac1000: Master AXI performs any burst length
[ 19.933266] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[ 19.938818] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
[ 19.947837] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 19.958145] br-lan: port 1(eth1.1) entered blocking state
[ 19.960431] br-lan: port 1(eth1.1) entered disabled state
[ 19.966197] device eth1.1 entered promiscuous mode
[ 19.971278] device eth1 entered promiscuous mode
[ 19.988004] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 19.999168] Generic PHY fixed-0:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=fixed-0:00, irq=POLL)
[ 19.999941] dwmac1000: Master AXI performs any burst length
[ 20.008161] ipq806x-gmac-dwmac 37200000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[ 20.013598] ipq806x-gmac-dwmac 37200000.ethernet eth0: registered PTP clock
[ 20.022985] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 20.050655] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready
[ 21.033961] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[ 21.034009] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[ 22.207131] ath10k_pci 0000:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
[ 22.207185] ath10k_pci 0000:01:00.0: msdu-desc: 2500 skid: 32
[ 22.283084] ath10k_pci 0000:01:00.0: wmi print ‘P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0’ [ 22.283847] ath10k_pci 0000:01:00.0: wmi print ‘free: 34244 iram: 32964 sram: 6508’ [ 22.617396] ath10k_pci 0000:01:00.0: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4
[ 22.617615] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 23.204265] ath10k_pci 0000:01:00.0: NOTE: Firmware DBGLOG output disabled in debug_mask: 0×10000000 [ 23.922442] ath10k_pci 0001:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
[ 23.922473] ath10k_pci 0001:01:00.0: msdu-desc: 2500 skid: 32
[ 23.999912] ath10k_pci 0001:01:00.0: wmi print ‘P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0’ [ 24.000735] ath10k_pci 0001:01:00.0: wmi print ‘free: 34244 iram: 32964 sram: 6508’ [ 24.360427] ath10k_pci 0001:01:00.0: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4
[ 24.360691] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 24.371374] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 24.376902] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
[ 24.382799] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 24.390294] br-lan: port 2(wlan0) entered blocking state
[ 24.395226] br-lan: port 2(wlan0) entered disabled state
[ 24.401012] device wlan0 entered promiscuous mode
[ 24.406967] br-lan: port 3(wlan1) entered blocking state
[ 24.410574] br-lan: port 3(wlan1) entered disabled state
[ 24.416200] device wlan1 entered promiscuous mode
[ 24.421480] br-lan: port 1(eth1.1) entered blocking state
[ 24.425909] br-lan: port 1(eth1.1) entered forwarding state
[ 24.444120] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 24.954027] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 24.954201] br-lan: port 3(wlan1) entered blocking state
[ 24.959463] br-lan: port 3(wlan1) entered forwarding state
[ 32.192222] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 32.192600] br-lan: port 2(wlan0) entered blocking state
[ 32.197780] br-lan: port 2(wlan0) entered forwarding state
[62765.216243] br-lan: port 3(wlan1) entered disabled state
[62765.216376] br-lan: port 2(wlan0) entered disabled state
[62765.220799] br-lan: port 1(eth1.1) entered disabled state
[62765.243250] device eth1.1 left promiscuous mode
[62765.243274] device eth1 left promiscuous mode
[62765.246818] br-lan: port 1(eth1.1) entered disabled state
[62765.300892] IPv6: ADDRCONF(NETDEV_UP): eth1.1: link is not ready
[62765.370915] device wlan0 left promiscuous mode
[62765.371017] br-lan: port 2(wlan0) entered disabled state
[62765.399751] device wlan1 left promiscuous mode
[62765.399947] br-lan: port 3(wlan1) entered disabled state
[62765.543982] Generic PHY fixed-0:01: attached PHY driver [Generic PHY] (mii_bus:phy_addr=fixed-0:01, irq=POLL)
[62765.544860] dwmac1000: Master AXI performs any burst length
[62765.553003] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[62765.558361] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
[62765.567464] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[62765.576509] br-lan: port 1(eth1.1) entered blocking state
[62765.580141] br-lan: port 1(eth1.1) entered disabled state
[62765.585758] device eth1.1 entered promiscuous mode
[62765.590960] device eth1 entered promiscuous mode
[62765.597219] br-lan: port 2(wlan0) entered blocking state
[62765.600467] br-lan: port 2(wlan0) entered disabled state
[62765.605937] device wlan0 entered promiscuous mode
[62765.614118] br-lan: port 3(wlan1) entered blocking state
[62765.615552] br-lan: port 3(wlan1) entered disabled state
[62765.621210] device wlan1 entered promiscuous mode
[62765.627588] br-lan: port 3(wlan1) entered blocking state
[62765.630904] br-lan: port 3(wlan1) entered forwarding state
[62765.636291] br-lan: port 2(wlan0) entered blocking state
[62765.641573] br-lan: port 2(wlan0) entered forwarding state
[62765.909185] device wlan0 left promiscuous mode
[62765.909272] br-lan: port 2(wlan0) entered disabled state
[62766.019722] ath10k_pci 0000:01:00.0: peer-unmap-event: unknown peer id 0
[62766.019819] ath10k_pci 0000:01:00.0: peer-unmap-event: unknown peer id 0
[62766.240632] device wlan1 left promiscuous mode
[62766.240717] br-lan: port 3(wlan1) entered disabled state
[62766.310654] ath10k_pci 0001:01:00.0: peer-unmap-event: unknown peer id 0
[62766.310744] ath10k_pci 0001:01:00.0: peer-unmap-event: unknown peer id 0
[62766.618743] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[62766.618789] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[62766.627173] br-lan: port 1(eth1.1) entered blocking state
[62766.632756] br-lan: port 1(eth1.1) entered forwarding state
[62767.994242] ath10k_pci 0000:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
[62767.994275] ath10k_pci 0000:01:00.0: msdu-desc: 2500 skid: 32
[62768.070252] ath10k_pci 0000:01:00.0: wmi print ‘P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0’ [62768.071045] ath10k_pci 0000:01:00.0: wmi print ‘free: 34244 iram: 32964 sram: 6508’ [62768.404901] ath10k_pci 0000:01:00.0: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4
[62768.405133] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[62768.426773] br-lan: port 2(wlan0) entered blocking state
[62768.426822] br-lan: port 2(wlan0) entered disabled state
[62768.431615] device wlan0 entered promiscuous mode
[62769.875984] ath10k_pci 0001:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
[62769.876016] ath10k_pci 0001:01:00.0: msdu-desc: 2500 skid: 32
[62769.953615] ath10k_pci 0001:01:00.0: wmi print ‘P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0’ [62769.954426] ath10k_pci 0001:01:00.0: wmi print ‘free: 34244 iram: 32964 sram: 6508’ [62770.359446] ath10k_pci 0001:01:00.0: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4
[62770.359742] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[62770.375466] br-lan: port 3(wlan1) entered blocking state
[62770.375529] br-lan: port 3(wlan1) entered disabled state
[62770.381546] device wlan1 entered promiscuous mode
[62770.804953] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[62770.805395] br-lan: port 3(wlan1) entered blocking state
[62770.810637] br-lan: port 3(wlan1) entered forwarding state
[62776.734909] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[62776.735257] br-lan: port 2(wlan0) entered blocking state
[62776.740484] br-lan: port 2(wlan0) entered forwarding state
[63069.307187] br-lan: port 3(wlan1) entered disabled state
[63069.307332] br-lan: port 2(wlan0) entered disabled state
[63069.311729] br-lan: port 1(eth1.1) entered disabled state
[63069.331741] device eth1.1 left promiscuous mode
[63069.331765] device eth1 left promiscuous mode
[63069.335230] br-lan: port 1(eth1.1) entered disabled state
[63069.367120] IPv6: ADDRCONF(NETDEV_UP): eth1.1: link is not ready
[63069.471014] device wlan0 left promiscuous mode
[63069.471245] br-lan: port 2(wlan0) entered disabled state
[63069.511009] device wlan1 left promiscuous mode
[63069.511259] br-lan: port 3(wlan1) entered disabled state
[63069.616492] Generic PHY fixed-0:01: attached PHY driver [Generic PHY] (mii_bus:phy_addr=fixed-0:01, irq=POLL)
[63069.617409] dwmac1000: Master AXI performs any burst length
[63069.625476] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[63069.630936] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
[63069.639962] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[63069.663482] br-lan: port 1(eth1.1) entered blocking state
[63069.663508] br-lan: port 1(eth1.1) entered disabled state
[63069.668223] device eth1.1 entered promiscuous mode
[63069.673319] device eth1 entered promiscuous mode
[63069.681698] br-lan: port 2(wlan0) entered blocking state
[63069.682705] br-lan: port 2(wlan0) entered disabled state
[63069.688210] device wlan0 entered promiscuous mode
[63069.695208] br-lan: port 3(wlan1) entered blocking state
[63069.697894] br-lan: port 3(wlan1) entered disabled state
[63069.703576] device wlan1 entered promiscuous mode
[63069.734325] br-lan: port 3(wlan1) entered blocking state
[63069.734355] br-lan: port 3(wlan1) entered forwarding state
[63069.738820] br-lan: port 2(wlan0) entered blocking state
[63069.744087] br-lan: port 2(wlan0) entered forwarding state
[63069.950176] device wlan0 left promiscuous mode
[63069.950285] br-lan: port 2(wlan0) entered disabled state
[63070.002464] ath10k_pci 0000:01:00.0: peer-unmap-event: unknown peer id 0
[63070.002548] ath10k_pci 0000:01:00.0: peer-unmap-event: unknown peer id 0
[63070.113839] device wlan1 left promiscuous mode
[63070.113951] br-lan: port 3(wlan1) entered disabled state
[63070.168952] ath10k_pci 0001:01:00.0: peer-unmap-event: unknown peer id 0
[63070.169052] ath10k_pci 0001:01:00.0: peer-unmap-event: unknown peer id 0
[63070.699940] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[63071.916259] ath10k_pci 0000:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
[63071.916288] ath10k_pci 0000:01:00.0: msdu-desc: 2500 skid: 32
[63071.992210] ath10k_pci 0000:01:00.0: wmi print ‘P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0’ [63071.992997] ath10k_pci 0000:01:00.0: wmi print ‘free: 34244 iram: 32964 sram: 6508’ [63072.325864] ath10k_pci 0000:01:00.0: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4
[63072.326099] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[63072.339921] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[63072.349420] br-lan: port 1(eth1.1) entered blocking state
[63072.349472] br-lan: port 1(eth1.1) entered forwarding state
[63072.357055] br-lan: port 2(wlan0) entered blocking state
[63072.359187] br-lan: port 2(wlan0) entered disabled state
[63072.365170] device wlan0 entered promiscuous mode
[63073.682694] ath10k_pci 0001:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
[63073.682721] ath10k_pci 0001:01:00.0: msdu-desc: 2500 skid: 32
[63073.760293] ath10k_pci 0001:01:00.0: wmi print ‘P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0’ [63073.761079] ath10k_pci 0001:01:00.0: wmi print ‘free: 34244 iram: 32964 sram: 6508’ [63074.115156] ath10k_pci 0001:01:00.0: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4
[63074.115394] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[63074.130842] br-lan: port 3(wlan1) entered blocking state
[63074.130920] br-lan: port 3(wlan1) entered disabled state
[63074.136931] device wlan1 entered promiscuous mode
[63074.551027] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[63074.551320] br-lan: port 3(wlan1) entered blocking state
[63074.556500] br-lan: port 3(wlan1) entered forwarding state
[63081.905095] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[63081.905458] br-lan: port 2(wlan0) entered blocking state
[63081.910636] br-lan: port 2(wlan0) entered forwarding state
[64977.403083] br-lan: port 3(wlan1) entered disabled state
[64977.403217] br-lan: port 2(wlan0) entered disabled state
[64977.407677] br-lan: port 1(eth1.1) entered disabled state
[64977.421744] device eth1.1 left promiscuous mode
[64977.421771] device eth1 left promiscuous mode
[64977.425229] br-lan: port 1(eth1.1) entered disabled state
[64977.468838] IPv6: ADDRCONF(NETDEV_UP): eth1.1: link is not ready
[64977.548513] device wlan0 left promiscuous mode
[64977.548630] br-lan: port 2(wlan0) entered disabled state
[64977.577767] device wlan1 left promiscuous mode
[64977.577915] br-lan: port 3(wlan1) entered disabled state
[64977.735104] Generic PHY fixed-0:01: attached PHY driver [Generic PHY] (mii_bus:phy_addr=fixed-0:01, irq=POLL)
[64977.736327] dwmac1000: Master AXI performs any burst length
[64977.744171] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[64977.749552] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
[64977.758594] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[64977.768033] br-lan: port 1(eth1.1) entered blocking state
[64977.771270] br-lan: port 1(eth1.1) entered disabled state
[64977.776871] device eth1.1 entered promiscuous mode
[64977.782091] device eth1 entered promiscuous mode
[64977.793832] br-lan: port 2(wlan0) entered blocking state
[64977.793861] br-lan: port 2(wlan0) entered disabled state
[64977.798509] device wlan0 entered promiscuous mode
[64977.820921] br-lan: port 3(wlan1) entered blocking state
[64977.820957] br-lan: port 3(wlan1) entered disabled state
[64977.825535] device wlan1 entered promiscuous mode
[64977.834354] br-lan: port 3(wlan1) entered blocking state
[64977.835206] br-lan: port 3(wlan1) entered forwarding state
[64977.840745] br-lan: port 2(wlan0) entered blocking state
[64977.845878] br-lan: port 2(wlan0) entered forwarding state
[64978.077249] device wlan0 left promiscuous mode
[64978.077362] br-lan: port 2(wlan0) entered disabled state
[64978.158428] ath10k_pci 0000:01:00.0: peer-unmap-event: unknown peer id 0
[64978.158479] ath10k_pci 0000:01:00.0: peer-unmap-event: unknown peer id 0
[64978.297331] device wlan1 left promiscuous mode
[64978.297435] br-lan: port 3(wlan1) entered disabled state
[64978.323270] ath10k_pci 0001:01:00.0: peer-unmap-event: unknown peer id 0
[64978.323360] ath10k_pci 0001:01:00.0: peer-unmap-event: unknown peer id 0
[64978.787101] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[64978.787148] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[64978.797946] br-lan: port 1(eth1.1) entered blocking state
[64978.801028] br-lan: port 1(eth1.1) entered forwarding state
[64980.203367] ath10k_pci 0000:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
[64980.203402] ath10k_pci 0000:01:00.0: msdu-desc: 2500 skid: 32
[64980.279376] ath10k_pci 0000:01:00.0: wmi print ‘P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0’ [64980.280185] ath10k_pci 0000:01:00.0: wmi print ‘free: 34244 iram: 32964 sram: 6508’ [64980.612924] ath10k_pci 0000:01:00.0: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4
[64980.613156] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[64980.648192] br-lan: port 2(wlan0) entered blocking state
[64980.648224] br-lan: port 2(wlan0) entered disabled state
[64980.652772] device wlan0 entered promiscuous mode
[64981.959570] ath10k_pci 0001:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
[64981.959599] ath10k_pci 0001:01:00.0: msdu-desc: 2500 skid: 32
[64982.037593] ath10k_pci 0001:01:00.0: wmi print ‘P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0’ [64982.038390] ath10k_pci 0001:01:00.0: wmi print ‘free: 34244 iram: 32964 sram: 6508’ [64982.423402] ath10k_pci 0001:01:00.0: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4
[64982.423677] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[64982.440876] br-lan: port 3(wlan1) entered blocking state
[64982.440904] br-lan: port 3(wlan1) entered disabled state
[64982.445516] device wlan1 entered promiscuous mode
[64982.878202] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[64982.878582] br-lan: port 3(wlan1) entered blocking state
[64982.883650] br-lan: port 3(wlan1) entered forwarding state
[64988.804253] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[64988.804552] br-lan: port 2(wlan0) entered blocking state
[64988.809815] br-lan: port 2(wlan0) entered forwarding state
[72002.069094] conntrack: generic helper won’t handle protocol 47. Please consider loading the specific helper module.

05.04.20202966Base systemBug ReportVery LowLowKernel msg "No memory allocated for crashlog" when boot...TrunkUnconfirmed Task Description

Whenever my Netgear r7500v2 running OpenWrt 19.07.2 is rebooted or power-cycled, the message ""No memory allocated for crashlog" is always shown in the kernel log.

If I try to simulate a kernel panic using "echo c > /proc/sysrq-trigger", no crashlog is generated in /sys/kernel/debug/.

KERNEL LOG - Netgear r7500v2 running 19.07.2

[ 0.043547] clocksource: Switched to clocksource dg_timer
[ 0.046802] NET: Registered protocol family 2
[ 0.047409] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.047450] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.047506] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.047600] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.047627] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.047808] NET: Registered protocol family 1
[ 0.047855] PCI: CLS 0 bytes, default 64

[ 0.049026] No memory allocated for crashlog

[ 0.049301] workingset: timestamp_bits=30 max_order=17 bucket_order=0
[ 0.054475] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.054494] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) © 2001-2006 Red Hat, Inc.
[ 0.061135] io scheduler noop registered
[ 0.061154] io scheduler deadline registered (default)
[ 0.062800] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda not found, using d

05.04.20202965Base systemBug ReportVery LowLowKernel msg "No memory allocated for crashlog" when boot...TrunkUnconfirmed Task Description

Whenever my Netgear r7500v2 running OpenWrt 19.07.2 is rebooted or power-cycled, the message ""No memory allocated for crashlog" is always shown in the kernel log.

If I try to simulate a kernel panic using "echo c > /proc/sysrq-trigger", no crashlog is generated in /sys/kernel/debug/.

KERNEL LOG - Netgear r7500v2 running 19.07.2

[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.14.171 (builder@buildhost) (gcc version 7.5.0 (OpenWrt GCC 7.5.0 r10947-65030d81f3)) #0 SMP Thu Feb 27 21:05:12 2020
[ 0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5787d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[ 0.000000] OF: fdt: Machine model: Netgear Nighthawk X4 R7500v2
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] On node 0 totalpages: 122880
[ 0.000000] free_area_init_node: node 0, pgdat c0a27880, node_mem_map dda39000
[ 0.000000] Normal zone: 960 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 122880 pages, LIFO batch:31
[ 0.000000] random: get_random_bytes called from 0xc09008dc with crng_init=0
[ 0.000000] percpu: Embedded 15 pages/cpu s29388 r8192 d23860 u61440
[ 0.000000] pcpu-alloc: s29388 r8192 d23860 u61440 alloc=15*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 121920
[ 0.000000] Kernel command line: rootfstype=squashfs noinitrd
[ 0.000000] Bootloader command line (ignored): console=ttyHSL1,115200n8
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 477380K/491520K available (4975K kernel code, 160K rwdata, 756K rodata, 1024K init, 235K bss, 14140K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xde800000 - 0xff800000 ( 528 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xde000000 ( 480 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0208000 - 0xc07dbe98 (5968 kB)
[ 0.000000] .init : 0xc0900000 - 0xc0a00000 (1024 kB)
[ 0.000000] .data : 0xc0a00000 - 0xc0a28180 ( 161 kB)
[ 0.000000] .bss : 0xc0a2a000 - 0xc0a64e18 ( 236 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] clocksource: dg_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 305801671480 ns
[ 0.000008] sched_clock: 32 bits at 6MHz, resolution 160ns, wraps every 343597383600ns
[ 0.000022] Switching to timer-based delay loop, resolution 160ns
[ 0.000229] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.50 BogoMIPS (lpj=62500)
[ 0.000255] pid_max: default: 32768 minimum: 301
[ 0.000382] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000400] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000916] CPU: Testing write buffer coherency: ok
[ 0.001695] Setting up static identity map for 0x42300000 - 0x42300060
[ 0.001848] Hierarchical SRCU implementation.
[ 0.002590] smp: Bringing up secondary CPUs ...
[ 0.004399] smp: Brought up 1 node, 2 CPUs
[ 0.004416] SMP: Total of 2 processors activated (25.00 BogoMIPS).
[ 0.004426] CPU: All CPU(s) started in SVC mode.
[ 0.014357] VFP support v0.3: implementor 51 architecture 64 part 4d variant 2 rev 0
[ 0.014521] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.014549] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.014656] pinctrl core: initialized pinctrl subsystem
[ 0.015648] NET: Registered protocol family 16
[ 0.015944] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.017300] cpuidle: using governor ladder
[ 0.017369] cpuidle: using governor menu
[ 0.039972] msm_bus_fabric_init_driver
[ 0.041523] usbcore: registered new interface driver usbfs
[ 0.041604] usbcore: registered new interface driver hub
[ 0.041691] usbcore: registered new device driver usb
[ 0.041748] pps_core: LinuxPPS API ver. 1 registered
[ 0.041760] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti giometti@linux.it [ 0.041792] PTP clock support registered
[ 0.043547] clocksource: Switched to clocksource dg_timer
[ 0.046802] NET: Registered protocol family 2
[ 0.047409] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.047450] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.047506] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.047600] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.047627] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.047808] NET: Registered protocol family 1
[ 0.047855] PCI: CLS 0 bytes, default 64
[ 0.049026] No memory allocated for crashlog
[ 0.049301] workingset: timestamp_bits=30 max_order=17 bucket_order=0
[ 0.054475] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.054494] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) © 2001-2006 Red Hat, Inc.
[ 0.061135] io scheduler noop registered
[ 0.061154] io scheduler deadline registered (default)
[ 0.062800] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda not found, using dummy regulator
[ 0.062919] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda_phy not found, using dummy regulator
[ 0.063022] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda_refclk not found, using dummy regulator
[ 0.063756] OF: PCI: host bridge /soc/pci@1b500000 ranges:
[ 0.063800] OF: PCI: IO 0x0fe00000..0x0fefffff → 0x0fe00000
[ 0.063824] OF: PCI: MEM 0x08000000..0x0fdfffff → 0x08000000
[ 0.172087] qcom-pcie 1b500000.pci: link up
[ 0.172252] qcom-pcie 1b500000.pci: PCI host bridge to bus 0000:00
[ 0.172276] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.172298] pci_bus 0000:00: root bus resource [io 0x0000-0xfffff] (bus address [0xfe00000-0xfefffff])
[ 0.172313] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fdfffff]
[ 0.172330] pci_bus 0000:00: scanning bus
[ 0.172376] pci 0000:00:00.0: [17cb:0101] type 01 class 0x060400
[ 0.172463] pci 0000:00:00.0: calling 0xc030d3c0
[ 0.172533] pci 0000:00:00.0: supports D1
[ 0.172544] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 0.172560] pci 0000:00:00.0: PME# disabled
[ 0.172816] pci_bus 0000:00: fixups for bus
[ 0.172839] PCI: bus0: Fast back to back transfers disabled
[ 0.172859] pci 0000:00:00.0: scanning [bus 01-ff] behind bridge, pass 0
[ 0.172987] pci_bus 0000:01: scanning bus
[ 0.173164] pci 0000:01:00.0: [168c:0040] type 00 class 0x028000
[ 0.173515] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[ 0.174088] pci 0000:01:00.0: calling 0xc030d3c0
[ 0.174731] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[ 0.174773] pci 0000:01:00.0: PME# disabled
[ 0.175109] pci_bus 0000:01: fixups for bus
[ 0.175180] PCI: bus1: Fast back to back transfers disabled
[ 0.175198] pci_bus 0000:01: bus scan returning with max=01
[ 0.175216] pci 0000:00:00.0: scanning [bus 01-ff] behind bridge, pass 1
[ 0.175233] pci_bus 0000:00: bus scan returning with max=ff
[ 0.175284] pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x081fffff]
[ 0.175309] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x081fffff 64bit]
[ 0.175439] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 0.175462] pci 0000:00:00.0: bridge window [mem 0x08000000-0x081fffff]
[ 0.175496] pci 0000:00:00.0: calling 0xc055fae4
[ 0.175691] pcieport 0000:00:00.0: assign IRQ: got 67
[ 0.176013] pcieport 0000:00:00.0: AER enabled with IRQ 35
[ 0.176129] pci 0000:01:00.0: calling 0xc055fae4
[ 0.176546] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda not found, using dummy regulator
[ 0.176666] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda_phy not found, using dummy regulator
[ 0.176761] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda_refclk not found, using dummy regulator
[ 0.177458] OF: PCI: host bridge /soc/pci@1b700000 ranges:
[ 0.177495] OF: PCI: IO 0x31e00000..0x31efffff → 0x31e00000
[ 0.177520] OF: PCI: MEM 0x2e000000..0x31dfffff → 0x2e000000
[ 0.287453] qcom-pcie 1b700000.pci: link up
[ 0.287604] qcom-pcie 1b700000.pci: PCI host bridge to bus 0001:00
[ 0.287625] pci_bus 0001:00: root bus resource [bus 00-ff]
[ 0.287641] pci_bus 0001:00: root bus resource [mem 0x2e000000-0x31dfffff]
[ 0.287655] pci_bus 0001:00: scanning bus
[ 0.287697] pci 0001:00:00.0: [17cb:0101] type 01 class 0x060400
[ 0.287769] pci 0001:00:00.0: calling 0xc030d3c0
[ 0.287830] pci 0001:00:00.0: supports D1
[ 0.287839] pci 0001:00:00.0: PME# supported from D0 D1 D3hot
[ 0.287854] pci 0001:00:00.0: PME# disabled
[ 0.288092] pci_bus 0001:00: fixups for bus
[ 0.288110] PCI: bus0: Fast back to back transfers disabled
[ 0.288128] pci 0001:00:00.0: scanning [bus 01-ff] behind bridge, pass 0
[ 0.288247] pci_bus 0001:01: scanning bus
[ 0.288434] pci 0001:01:00.0: [168c:0040] type 00 class 0x028000
[ 0.288807] pci 0001:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[ 0.289305] pci 0001:01:00.0: calling 0xc030d3c0
[ 0.289996] pci 0001:01:00.0: PME# supported from D0 D3hot D3cold
[ 0.290041] pci 0001:01:00.0: PME# disabled
[ 0.290384] pci_bus 0001:01: fixups for bus
[ 0.290460] PCI: bus1: Fast back to back transfers disabled
[ 0.290475] pci_bus 0001:01: bus scan returning with max=01
[ 0.290491] pci 0001:00:00.0: scanning [bus 01-ff] behind bridge, pass 1
[ 0.290508] pci_bus 0001:00: bus scan returning with max=ff
[ 0.290544] pci 0001:00:00.0: BAR 8: assigned [mem 0x2e000000-0x2e1fffff]
[ 0.290568] pci 0001:01:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit]
[ 0.290700] pci 0001:00:00.0: PCI bridge to [bus 01-ff]
[ 0.290722] pci 0001:00:00.0: bridge window [mem 0x2e000000-0x2e1fffff]
[ 0.290752] pci 0001:00:00.0: calling 0xc055fae4
[ 0.290933] pcieport 0001:00:00.0: assign IRQ: got 100
[ 0.291229] pcieport 0001:00:00.0: AER enabled with IRQ 68
[ 0.291338] pci 0001:01:00.0: calling 0xc055fae4
[ 0.293608] L2 @ QSB rate. Forcing new rate.
[ 0.293943] L2 @ 384000 KHz
[ 0.294121] CPU0 @ 800000 KHz
[ 0.294134] CPU1 @ QSB rate. Forcing new rate.
[ 0.294260] CPU1 @ 384000 KHz
[ 0.298165] gsbi 16300000.gsbi: GSBI port protocol: 6 crci: 0
[ 0.300055] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.302639] msm_serial 16340000.serial: msm_serial: detected port #0
[ 0.302736] msm_serial 16340000.serial: uartclk = 7372800
[ 0.302820] 16340000.serial: ttyMSM0 at MMIO 0x16340000 (irq = 101, base_baud = 460800) is a MSM
[ 0.302857] msm_serial: console setup on port #0
[ 1.025206] console [ttyMSM0] enabled
[ 1.029901] msm_serial: driver initialized
[ 1.038615] loop: module loaded
[ 1.040683] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xa1
[ 1.040714] nand: Micron MT29F1G08ABBEAH4
[ 1.047271] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 1.051179] 8 fixed-partitions partitions found on MTD device qcom_nand.0
[ 1.058606] Creating 8 MTD partitions on "qcom_nand.0":
[ 1.065491] 0x000000000000-0x000000c80000 : "qcadata"
[ 1.075531] random: fast init done
[ 1.093285] 0x000000c80000-0x000001180000 : "APPSBL"
[ 1.102841] 0x000001180000-0x000001200000 : "APPSBLENV"
[ 1.104548] 0x000001200000-0x000001340000 : "art"
[ 1.109810] 0x000001340000-0x000001480000 : "artbak"
[ 1.114731] 0x000001480000-0x000001880000 : "kernel"
[ 1.124591] 0x000001880000-0x000007900000 : "ubi"
[ 1.293621] 0x000007900000-0x000008000000 : "reserve"
[ 1.307906] libphy: GPIO Bitbanged MDIO: probed
[ 1.329381] switch0: Atheros AR8337 rev. 2 switch registered on gpio-0
[ 2.176103] ar8327: qca,phy-rgmii-en is not specified
[ 2.176492] libphy: Fixed MDIO Bus: probed
[ 2.182240] ipq806x-gmac-dwmac 37200000.ethernet: PTP uses main clock
[ 2.184529] stmmac - user ID: 0x10, Synopsys ID: 0x37
[ 2.190647] ipq806x-gmac-dwmac 37200000.ethernet: Ring mode enabled
[ 2.195757] ipq806x-gmac-dwmac 37200000.ethernet: DMA HW capability register supported
[ 2.201760] ipq806x-gmac-dwmac 37200000.ethernet: Enhanced/Alternate descriptors
[ 2.209805] ipq806x-gmac-dwmac 37200000.ethernet: Enabled extended descriptors
[ 2.217364] ipq806x-gmac-dwmac 37200000.ethernet: RX Checksum Offload Engine supported
[ 2.224395] ipq806x-gmac-dwmac 37200000.ethernet: COE Type 2
[ 2.232224] ipq806x-gmac-dwmac 37200000.ethernet: TX Checksum insertion supported
[ 2.238106] ipq806x-gmac-dwmac 37200000.ethernet: Wake-Up On Lan supported
[ 2.245484] ipq806x-gmac-dwmac 37200000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 2.253897] ipq806x-gmac-dwmac 37400000.ethernet: PTP uses main clock
[ 2.260973] stmmac - user ID: 0x10, Synopsys ID: 0x37
[ 2.267198] ipq806x-gmac-dwmac 37400000.ethernet: Ring mode enabled
[ 2.272156] ipq806x-gmac-dwmac 37400000.ethernet: DMA HW capability register supported
[ 2.278315] ipq806x-gmac-dwmac 37400000.ethernet: Enhanced/Alternate descriptors
[ 2.286278] ipq806x-gmac-dwmac 37400000.ethernet: Enabled extended descriptors
[ 2.293836] ipq806x-gmac-dwmac 37400000.ethernet: RX Checksum Offload Engine supported
[ 2.300803] ipq806x-gmac-dwmac 37400000.ethernet: COE Type 2
[ 2.308771] ipq806x-gmac-dwmac 37400000.ethernet: TX Checksum insertion supported
[ 2.314583] ipq806x-gmac-dwmac 37400000.ethernet: Wake-Up On Lan supported
[ 2.321898] ipq806x-gmac-dwmac 37400000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 2.329412] i2c /dev entries driver
[ 2.338177] Calibration not found.
[ 2.341644] Speed bin: 0
[ 2.344021] PVS bin: 1
[ 2.347907] cpuidle: enable-method property 'qcom,kpss-acc-v1' found operations
[ 2.348868] cpuidle: enable-method property 'qcom,kpss-acc-v1' found operations
[ 2.356707] sdhci: Secure Digital Host Controller Interface driver
[ 2.363298] sdhci: Copyright© Pierre Ossman
[ 2.369627] sdhci-pltfm: SDHCI platform and OF driver helper
[ 2.375443] NET: Registered protocol family 10
[ 2.381101] Segment Routing with IPv6
[ 2.384127] NET: Registered protocol family 17
[ 2.387743] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 2.392700] 8021q: 802.1Q VLAN Support v1.8
[ 2.405292] Registering SWP/SWPB emulation handler
[ 2.421323] qcom_rpm 108000.rpm: RPM firmware 3.0.16777342
[ 2.432804] s1a: supplied by regulator-dummy
[ 2.432906] s1a: Bringing 0uV into 1050000-1050000uV
[ 2.436504] s1b: supplied by regulator-dummy
[ 2.441137] s1b: Bringing 0uV into 1050000-1050000uV
[ 2.445691] s2a: supplied by regulator-dummy
[ 2.450341] s2a: Bringing 0uV into 800000-800000uV
[ 2.454857] s2b: supplied by regulator-dummy
[ 2.459202] s2b: Bringing 0uV into 800000-800000uV
[ 2.468388] UBI: auto-attach mtd6
[ 2.468420] ubi0: attaching mtd6
[ 2.519756] random: crng init done
[ 3.203591] ubi0: scanning is finished
[ 3.213668] ubi0: attached mtd6 (name "ubi", size 96 MiB)
[ 3.213689] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 3.218037] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 3.224890] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 3.231665] ubi0: good PEBs: 772, bad PEBs: 0, corrupted PEBs: 0
[ 3.238497] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[ 3.244746] ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 152459084
[ 3.251722] ubi0: available PEBs: 0, total reserved PEBs: 772, PEBs reserved for bad PEB handling: 20
[ 3.260811] ubi0: background thread "ubi_bgt0d" started, PID 59
[ 3.261484] block ubiblock0_0: created from ubi0:0(rootfs)
[ 3.275831] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[ 3.281321] hctosys: unable to open rtc device (rtc0)
[ 3.293054] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 3.294855] Freeing unused kernel memory: 1024K
[ 3.733321] init: Console is alive
[ 3.733456] init: - watchdog -
[ 4.288846] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 4.400142] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 4.403625] SCSI subsystem initialized
[ 4.410050] libata version 3.00 loaded.
[ 4.413158] ahci 29000000.sata: forcing port_map 0x0 → 0x1
[ 4.413230] ahci 29000000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode
[ 4.417662] ahci 29000000.sata: flags: ncq sntf pm led clo only pmp pio slum part ccc apst
[ 4.427114] scsi host0: ahci
[ 4.434724] ata1: SATA max UDMA/133 mmio [mem 0x29000000-0x2900017f] port 0x100 irq 26
[ 4.766181] ata1: SATA link down (SStatus 0 SControl 300)
[ 4.769356] ehci-platform: EHCI generic platform driver
[ 4.776396] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 4.777280] ohci-platform: OHCI generic platform driver
[ 4.910368] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 4.910459] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 4.915181] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000000002010010
[ 4.922400] xhci-hcd xhci-hcd.0.auto: irq 105, io mem 0x11000000
[ 4.932480] hub 1-0:1.0: USB hub found
[ 4.938104] hub 1-0:1.0: 1 port detected
[ 4.941701] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 4.945658] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 4.950867] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
[ 4.958583] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 4.965444] hub 2-0:1.0: USB hub found
[ 4.973368] hub 2-0:1.0: 1 port detected
[ 4.977232] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 4.980996] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
[ 4.986504] xhci-hcd xhci-hcd.1.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000000002010010
[ 4.993931] xhci-hcd xhci-hcd.1.auto: irq 106, io mem 0x10000000
[ 5.003612] hub 3-0:1.0: USB hub found
[ 5.009566] hub 3-0:1.0: 1 port detected
[ 5.013216] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 5.017156] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
[ 5.022396] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
[ 5.030118] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[ 5.036981] hub 4-0:1.0: USB hub found
[ 5.044986] hub 4-0:1.0: 1 port detected
[ 5.050128] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 5.057984] init: - preinit -
[ 6.781373] Generic PHY fixed-0:01: attached PHY driver [Generic PHY] (mii_bus:phy_addr=fixed-0:01, irq=POLL)
[ 6.783007] dwmac1000: Master AXI performs any burst length
[ 6.790440] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[ 6.795942] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
[ 6.805639] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 7.833932] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[ 7.834011] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 10.029570] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 143
[ 10.101636] UBIFS (ubi0:1): recovery needed
[ 10.227770] UBIFS (ubi0:1): recovery completed
[ 10.227843] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[ 10.231099] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 10.239072] UBIFS (ubi0:1): FS size: 90279936 bytes (86 MiB, 711 LEBs), journal size 4571136 bytes (4 MiB, 36 LEBs)
[ 10.248974] UBIFS (ubi0:1): reserved for root: 4264143 bytes (4164 KiB)
[ 10.259189] UBIFS (ubi0:1): media format: w4/r0 (latest is w5/r0), UUID E2C3B09D-9870-41F3-A16D-83335278F48C, small LPT model
[ 10.281904] mount_root: switching to ubifs overlay
[ 10.301239] urandom-seed: Seeding with /etc/urandom.seed
[ 10.471541] procd: - early -
[ 10.471670] procd: - watchdog -
[ 11.142803] procd: - watchdog -
[ 11.143313] procd: - ubus -
[ 11.237156] procd: - init -
[ 11.650168] urngd: v1.0.2 started.
[ 11.676844] kmodloader: loading kernel modules from /etc/modules.d/*
[ 11.681488] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 11.686329] Loading modules backported from Linux version v4.19.98-0-gd183c8e2647a
[ 11.687554] Backport generated by backports.git v4.19.98-1-0-g8204eb99
[ 11.695962] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 11.704177] nf_conntrack version 0.5.0 (8192 buckets, 32768 max)
[ 11.761069] wireguard: WireGuard 0.0.20190702 loaded. See www.wireguard.com for information.
[ 11.761112] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld Jason@zx2c4.com. All Rights Reserved.
[ 11.773657] xt_time: kernel timezone is -0000
[ 11.804583] PPP generic driver version 2.4.2
[ 11.805557] NET: Registered protocol family 24
[ 11.815317] ath10k_pci 0000:01:00.0: assign IRQ: got 67
[ 11.815340] ath10k 4.19 driver, optimized for CT firmware, probing pci device: 0x40.
[ 11.815747] ath10k_pci 0000:01:00.0: enabling device (0140 → 0142)
[ 11.822199] ath10k_pci 0000:01:00.0: enabling bus mastering
[ 11.822659] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[ 11.998510] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/fwcfg-pci-0000:01:00.0.txt failed with error -2
[ 11.998556] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 12.091038] firmware ath10k!fwcfg-pci-0000:01:00.0.txt: firmware_loading_store: map pages failed
[ 12.093273] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA99X0/hw2.0/ct-firmware-5.bin failed with error -2
[ 12.098991] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 12.133002] firmware ath10k!QCA99X0!hw2.0!ct-firmware-5.bin: firmware_loading_store: map pages failed
[ 12.133222] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA99X0/hw2.0/ct-firmware-2.bin failed with error -2
[ 12.141301] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 12.170070] firmware ath10k!QCA99X0!hw2.0!ct-firmware-2.bin: firmware_loading_store: map pages failed
[ 12.170327] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA99X0/hw2.0/firmware-6.bin failed with error -2
[ 12.178375] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 12.205811] firmware ath10k!QCA99X0!hw2.0!firmware-6.bin: firmware_loading_store: map pages failed
[ 12.475389] ath10k_pci 0000:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003b01ff sub 168c:0002
[ 12.475452] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[ 12.489548] ath10k_pci 0000:01:00.0: firmware ver 10.4b-ct-9980-fW-012-17ba9833 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 0fb1435e
[ 12.556781] ath10k_pci 0000:01:00.0: board_file api 2 bmi_id 1:1 crc32 08fa09f2
[ 13.742806] ath10k_pci 0000:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
[ 13.742836] ath10k_pci 0000:01:00.0: msdu-desc: 2500 skid: 32
[ 13.818824] ath10k_pci 0000:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
[ 13.819600] ath10k_pci 0000:01:00.0: wmi print 'free: 34244 iram: 32964 sram: 6508'
[ 14.061437] ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1
[ 14.166375] ath: EEPROM regdomain: 0x0
[ 14.166390] ath: EEPROM indicates default country code should be used
[ 14.166400] ath: doing EEPROM country→regdmn map search
[ 14.166418] ath: country maps to regdmn code: 0x3a
[ 14.166431] ath: Country alpha2 being used: US
[ 14.166442] ath: Regpair used: 0x3a
[ 14.171923] ath10k_pci 0001:01:00.0: assign IRQ: got 100
[ 14.171965] ath10k 4.19 driver, optimized for CT firmware, probing pci device: 0x40.
[ 14.173040] ath10k_pci 0001:01:00.0: enabling device (0140 → 0142)
[ 14.179020] ath10k_pci 0001:01:00.0: enabling bus mastering
[ 14.179701] ath10k_pci 0001:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[ 14.355448] ath10k_pci 0001:01:00.0: Direct firmware load for ath10k/fwcfg-pci-0001:01:00.0.txt failed with error -2
[ 14.355481] ath10k_pci 0001:01:00.0: Falling back to user helper
[ 14.537604] firmware ath10k!fwcfg-pci-0001:01:00.0.txt: firmware_loading_store: map pages failed
[ 14.540007] ath10k_pci 0001:01:00.0: Direct firmware load for ath10k/QCA99X0/hw2.0/ct-firmware-5.bin failed with error -2
[ 14.545575] ath10k_pci 0001:01:00.0: Falling back to user helper
[ 14.588731] firmware ath10k!QCA99X0!hw2.0!ct-firmware-5.bin: firmware_loading_store: map pages failed
[ 14.588988] ath10k_pci 0001:01:00.0: Direct firmware load for ath10k/QCA99X0/hw2.0/ct-firmware-2.bin failed with error -2
[ 14.597028] ath10k_pci 0001:01:00.0: Falling back to user helper
[ 14.630325] firmware ath10k!QCA99X0!hw2.0!ct-firmware-2.bin: firmware_loading_store: map pages failed
[ 14.630506] ath10k_pci 0001:01:00.0: Direct firmware load for ath10k/QCA99X0/hw2.0/firmware-6.bin failed with error -2
[ 14.638635] ath10k_pci 0001:01:00.0: Falling back to user helper
[ 14.695699] firmware ath10k!QCA99X0!hw2.0!firmware-6.bin: firmware_loading_store: map pages failed
[ 14.695869] ath10k_pci 0001:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003b01ff sub 168c:0002
[ 14.703563] ath10k_pci 0001:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[ 14.715193] ath10k_pci 0001:01:00.0: firmware ver 10.4b-ct-9980-fW-012-17ba9833 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 0fb1435e
[ 14.785906] ath10k_pci 0001:01:00.0: board_file api 2 bmi_id 1:2 crc32 08fa09f2
[ 15.975146] ath10k_pci 0001:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
[ 15.975173] ath10k_pci 0001:01:00.0: msdu-desc: 2500 skid: 32
[ 16.052629] ath10k_pci 0001:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
[ 16.053436] ath10k_pci 0001:01:00.0: wmi print 'free: 34244 iram: 32964 sram: 6508'
[ 16.272699] ath10k_pci 0001:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1
[ 16.396873] ath: EEPROM regdomain: 0x0
[ 16.396889] ath: EEPROM indicates default country code should be used
[ 16.396899] ath: doing EEPROM country→regdmn map search
[ 16.396916] ath: country maps to regdmn code: 0x3a
[ 16.396931] ath: Country alpha2 being used: US
[ 16.396942] ath: Regpair used: 0x3a
[ 16.405823] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 19.924371] Generic PHY fixed-0:01: attached PHY driver [Generic PHY] (mii_bus:phy_addr=fixed-0:01, irq=POLL)
[ 19.925264] dwmac1000: Master AXI performs any burst length
[ 19.933266] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[ 19.938818] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
[ 19.947837] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 19.958145] br-lan: port 1(eth1.1) entered blocking state
[ 19.960431] br-lan: port 1(eth1.1) entered disabled state
[ 19.966197] device eth1.1 entered promiscuous mode
[ 19.971278] device eth1 entered promiscuous mode
[ 19.988004] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 19.999168] Generic PHY fixed-0:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=fixed-0:00, irq=POLL)
[ 19.999941] dwmac1000: Master AXI performs any burst length
[ 20.008161] ipq806x-gmac-dwmac 37200000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[ 20.013598] ipq806x-gmac-dwmac 37200000.ethernet eth0: registered PTP clock
[ 20.022985] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 20.050655] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready
[ 21.033961] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[ 21.034009] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[ 22.207131] ath10k_pci 0000:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
[ 22.207185] ath10k_pci 0000:01:00.0: msdu-desc: 2500 skid: 32
[ 22.283084] ath10k_pci 0000:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
[ 22.283847] ath10k_pci 0000:01:00.0: wmi print 'free: 34244 iram: 32964 sram: 6508'
[ 22.617396] ath10k_pci 0000:01:00.0: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4
[ 22.617615] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 23.204265] ath10k_pci 0000:01:00.0: NOTE: Firmware DBGLOG output disabled in debug_mask: 0x10000000
[ 23.922442] ath10k_pci 0001:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
[ 23.922473] ath10k_pci 0001:01:00.0: msdu-desc: 2500 skid: 32
[ 23.999912] ath10k_pci 0001:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
[ 24.000735] ath10k_pci 0001:01:00.0: wmi print 'free: 34244 iram: 32964 sram: 6508'
[ 24.360427] ath10k_pci 0001:01:00.0: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4
[ 24.360691] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 24.371374] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 24.376902] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
[ 24.382799] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 24.390294] br-lan: port 2(wlan0) entered blocking state
[ 24.395226] br-lan: port 2(wlan0) entered disabled state
[ 24.401012] device wlan0 entered promiscuous mode
[ 24.406967] br-lan: port 3(wlan1) entered blocking state
[ 24.410574] br-lan: port 3(wlan1) entered disabled state
[ 24.416200] device wlan1 entered promiscuous mode
[ 24.421480] br-lan: port 1(eth1.1) entered blocking state
[ 24.425909] br-lan: port 1(eth1.1) entered forwarding state
[ 24.444120] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 24.954027] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 24.954201] br-lan: port 3(wlan1) entered blocking state
[ 24.959463] br-lan: port 3(wlan1) entered forwarding state
[ 32.192222] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 32.192600] br-lan: port 2(wlan0) entered blocking state
[ 32.197780] br-lan: port 2(wlan0) entered forwarding state
[62765.216243] br-lan: port 3(wlan1) entered disabled state
[62765.216376] br-lan: port 2(wlan0) entered disabled state
[62765.220799] br-lan: port 1(eth1.1) entered disabled state
[62765.243250] device eth1.1 left promiscuous mode
[62765.243274] device eth1 left promiscuous mode
[62765.246818] br-lan: port 1(eth1.1) entered disabled state
[62765.300892] IPv6: ADDRCONF(NETDEV_UP): eth1.1: link is not ready
[62765.370915] device wlan0 left promiscuous mode
[62765.371017] br-lan: port 2(wlan0) entered disabled state
[62765.399751] device wlan1 left promiscuous mode
[62765.399947] br-lan: port 3(wlan1) entered disabled state
[62765.543982] Generic PHY fixed-0:01: attached PHY driver [Generic PHY] (mii_bus:phy_addr=fixed-0:01, irq=POLL)
[62765.544860] dwmac1000: Master AXI performs any burst length
[62765.553003] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[62765.558361] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
[62765.567464] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[62765.576509] br-lan: port 1(eth1.1) entered blocking state
[62765.580141] br-lan: port 1(eth1.1) entered disabled state
[62765.585758] device eth1.1 entered promiscuous mode
[62765.590960] device eth1 entered promiscuous mode
[62765.597219] br-lan: port 2(wlan0) entered blocking state
[62765.600467] br-lan: port 2(wlan0) entered disabled state
[62765.605937] device wlan0 entered promiscuous mode
[62765.614118] br-lan: port 3(wlan1) entered blocking state
[62765.615552] br-lan: port 3(wlan1) entered disabled state
[62765.621210] device wlan1 entered promiscuous mode
[62765.627588] br-lan: port 3(wlan1) entered blocking state
[62765.630904] br-lan: port 3(wlan1) entered forwarding state
[62765.636291] br-lan: port 2(wlan0) entered blocking state
[62765.641573] br-lan: port 2(wlan0) entered forwarding state
[62765.909185] device wlan0 left promiscuous mode
[62765.909272] br-lan: port 2(wlan0) entered disabled state
[62766.019722] ath10k_pci 0000:01:00.0: peer-unmap-event: unknown peer id 0
[62766.019819] ath10k_pci 0000:01:00.0: peer-unmap-event: unknown peer id 0
[62766.240632] device wlan1 left promiscuous mode
[62766.240717] br-lan: port 3(wlan1) entered disabled state
[62766.310654] ath10k_pci 0001:01:00.0: peer-unmap-event: unknown peer id 0
[62766.310744] ath10k_pci 0001:01:00.0: peer-unmap-event: unknown peer id 0
[62766.618743] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[62766.618789] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[62766.627173] br-lan: port 1(eth1.1) entered blocking state
[62766.632756] br-lan: port 1(eth1.1) entered forwarding state
[62767.994242] ath10k_pci 0000:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
[62767.994275] ath10k_pci 0000:01:00.0: msdu-desc: 2500 skid: 32
[62768.070252] ath10k_pci 0000:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
[62768.071045] ath10k_pci 0000:01:00.0: wmi print 'free: 34244 iram: 32964 sram: 6508'
[62768.404901] ath10k_pci 0000:01:00.0: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4
[62768.405133] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[62768.426773] br-lan: port 2(wlan0) entered blocking state
[62768.426822] br-lan: port 2(wlan0) entered disabled state
[62768.431615] device wlan0 entered promiscuous mode
[62769.875984] ath10k_pci 0001:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
[62769.876016] ath10k_pci 0001:01:00.0: msdu-desc: 2500 skid: 32
[62769.953615] ath10k_pci 0001:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
[62769.954426] ath10k_pci 0001:01:00.0: wmi print 'free: 34244 iram: 32964 sram: 6508'
[62770.359446] ath10k_pci 0001:01:00.0: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4
[62770.359742] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[62770.375466] br-lan: port 3(wlan1) entered blocking state
[62770.375529] br-lan: port 3(wlan1) entered disabled state
[62770.381546] device wlan1 entered promiscuous mode
[62770.804953] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[62770.805395] br-lan: port 3(wlan1) entered blocking state
[62770.810637] br-lan: port 3(wlan1) entered forwarding state
[62776.734909] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[62776.735257] br-lan: port 2(wlan0) entered blocking state
[62776.740484] br-lan: port 2(wlan0) entered forwarding state
[63069.307187] br-lan: port 3(wlan1) entered disabled state
[63069.307332] br-lan: port 2(wlan0) entered disabled state
[63069.311729] br-lan: port 1(eth1.1) entered disabled state
[63069.331741] device eth1.1 left promiscuous mode
[63069.331765] device eth1 left promiscuous mode
[63069.335230] br-lan: port 1(eth1.1) entered disabled state
[63069.367120] IPv6: ADDRCONF(NETDEV_UP): eth1.1: link is not ready
[63069.471014] device wlan0 left promiscuous mode
[63069.471245] br-lan: port 2(wlan0) entered disabled state
[63069.511009] device wlan1 left promiscuous mode
[63069.511259] br-lan: port 3(wlan1) entered disabled state
[63069.616492] Generic PHY fixed-0:01: attached PHY driver [Generic PHY] (mii_bus:phy_addr=fixed-0:01, irq=POLL)
[63069.617409] dwmac1000: Master AXI performs any burst length
[63069.625476] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[63069.630936] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
[63069.639962] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[63069.663482] br-lan: port 1(eth1.1) entered blocking state
[63069.663508] br-lan: port 1(eth1.1) entered disabled state
[63069.668223] device eth1.1 entered promiscuous mode
[63069.673319] device eth1 entered promiscuous mode
[63069.681698] br-lan: port 2(wlan0) entered blocking state
[63069.682705] br-lan: port 2(wlan0) entered disabled state
[63069.688210] device wlan0 entered promiscuous mode
[63069.695208] br-lan: port 3(wlan1) entered blocking state
[63069.697894] br-lan: port 3(wlan1) entered disabled state
[63069.703576] device wlan1 entered promiscuous mode
[63069.734325] br-lan: port 3(wlan1) entered blocking state
[63069.734355] br-lan: port 3(wlan1) entered forwarding state
[63069.738820] br-lan: port 2(wlan0) entered blocking state
[63069.744087] br-lan: port 2(wlan0) entered forwarding state
[63069.950176] device wlan0 left promiscuous mode
[63069.950285] br-lan: port 2(wlan0) entered disabled state
[63070.002464] ath10k_pci 0000:01:00.0: peer-unmap-event: unknown peer id 0
[63070.002548] ath10k_pci 0000:01:00.0: peer-unmap-event: unknown peer id 0
[63070.113839] device wlan1 left promiscuous mode
[63070.113951] br-lan: port 3(wlan1) entered disabled state
[63070.168952] ath10k_pci 0001:01:00.0: peer-unmap-event: unknown peer id 0
[63070.169052] ath10k_pci 0001:01:00.0: peer-unmap-event: unknown peer id 0
[63070.699940] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[63071.916259] ath10k_pci 0000:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
[63071.916288] ath10k_pci 0000:01:00.0: msdu-desc: 2500 skid: 32
[63071.992210] ath10k_pci 0000:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
[63071.992997] ath10k_pci 0000:01:00.0: wmi print 'free: 34244 iram: 32964 sram: 6508'
[63072.325864] ath10k_pci 0000:01:00.0: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4
[63072.326099] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[63072.339921] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[63072.349420] br-lan: port 1(eth1.1) entered blocking state
[63072.349472] br-lan: port 1(eth1.1) entered forwarding state
[63072.357055] br-lan: port 2(wlan0) entered blocking state
[63072.359187] br-lan: port 2(wlan0) entered disabled state
[63072.365170] device wlan0 entered promiscuous mode
[63073.682694] ath10k_pci 0001:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
[63073.682721] ath10k_pci 0001:01:00.0: msdu-desc: 2500 skid: 32
[63073.760293] ath10k_pci 0001:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
[63073.761079] ath10k_pci 0001:01:00.0: wmi print 'free: 34244 iram: 32964 sram: 6508'
[63074.115156] ath10k_pci 0001:01:00.0: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4
[63074.115394] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[63074.130842] br-lan: port 3(wlan1) entered blocking state
[63074.130920] br-lan: port 3(wlan1) entered disabled state
[63074.136931] device wlan1 entered promiscuous mode
[63074.551027] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[63074.551320] br-lan: port 3(wlan1) entered blocking state
[63074.556500] br-lan: port 3(wlan1) entered forwarding state
[63081.905095] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[63081.905458] br-lan: port 2(wlan0) entered blocking state
[63081.910636] br-lan: port 2(wlan0) entered forwarding state
[64977.403083] br-lan: port 3(wlan1) entered disabled state
[64977.403217] br-lan: port 2(wlan0) entered disabled state
[64977.407677] br-lan: port 1(eth1.1) entered disabled state
[64977.421744] device eth1.1 left promiscuous mode
[64977.421771] device eth1 left promiscuous mode
[64977.425229] br-lan: port 1(eth1.1) entered disabled state
[64977.468838] IPv6: ADDRCONF(NETDEV_UP): eth1.1: link is not ready
[64977.548513] device wlan0 left promiscuous mode
[64977.548630] br-lan: port 2(wlan0) entered disabled state
[64977.577767] device wlan1 left promiscuous mode
[64977.577915] br-lan: port 3(wlan1) entered disabled state
[64977.735104] Generic PHY fixed-0:01: attached PHY driver [Generic PHY] (mii_bus:phy_addr=fixed-0:01, irq=POLL)
[64977.736327] dwmac1000: Master AXI performs any burst length
[64977.744171] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[64977.749552] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
[64977.758594] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[64977.768033] br-lan: port 1(eth1.1) entered blocking state
[64977.771270] br-lan: port 1(eth1.1) entered disabled state
[64977.776871] device eth1.1 entered promiscuous mode
[64977.782091] device eth1 entered promiscuous mode
[64977.793832] br-lan: port 2(wlan0) entered blocking state
[64977.793861] br-lan: port 2(wlan0) entered disabled state
[64977.798509] device wlan0 entered promiscuous mode
[64977.820921] br-lan: port 3(wlan1) entered blocking state
[64977.820957] br-lan: port 3(wlan1) entered disabled state
[64977.825535] device wlan1 entered promiscuous mode
[64977.834354] br-lan: port 3(wlan1) entered blocking state
[64977.835206] br-lan: port 3(wlan1) entered forwarding state
[64977.840745] br-lan: port 2(wlan0) entered blocking state
[64977.845878] br-lan: port 2(wlan0) entered forwarding state
[64978.077249] device wlan0 left promiscuous mode
[64978.077362] br-lan: port 2(wlan0) entered disabled state
[64978.158428] ath10k_pci 0000:01:00.0: peer-unmap-event: unknown peer id 0
[64978.158479] ath10k_pci 0000:01:00.0: peer-unmap-event: unknown peer id 0
[64978.297331] device wlan1 left promiscuous mode
[64978.297435] br-lan: port 3(wlan1) entered disabled state
[64978.323270] ath10k_pci 0001:01:00.0: peer-unmap-event: unknown peer id 0
[64978.323360] ath10k_pci 0001:01:00.0: peer-unmap-event: unknown peer id 0
[64978.787101] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[64978.787148] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[64978.797946] br-lan: port 1(eth1.1) entered blocking state
[64978.801028] br-lan: port 1(eth1.1) entered forwarding state
[64980.203367] ath10k_pci 0000:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
[64980.203402] ath10k_pci 0000:01:00.0: msdu-desc: 2500 skid: 32
[64980.279376] ath10k_pci 0000:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
[64980.280185] ath10k_pci 0000:01:00.0: wmi print 'free: 34244 iram: 32964 sram: 6508'
[64980.612924] ath10k_pci 0000:01:00.0: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4
[64980.613156] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[64980.648192] br-lan: port 2(wlan0) entered blocking state
[64980.648224] br-lan: port 2(wlan0) entered disabled state
[64980.652772] device wlan0 entered promiscuous mode
[64981.959570] ath10k_pci 0001:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
[64981.959599] ath10k_pci 0001:01:00.0: msdu-desc: 2500 skid: 32
[64982.037593] ath10k_pci 0001:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
[64982.038390] ath10k_pci 0001:01:00.0: wmi print 'free: 34244 iram: 32964 sram: 6508'
[64982.423402] ath10k_pci 0001:01:00.0: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4
[64982.423677] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[64982.440876] br-lan: port 3(wlan1) entered blocking state
[64982.440904] br-lan: port 3(wlan1) entered disabled state
[64982.445516] device wlan1 entered promiscuous mode
[64982.878202] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[64982.878582] br-lan: port 3(wlan1) entered blocking state
[64982.883650] br-lan: port 3(wlan1) entered forwarding state
[64988.804253] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[64988.804552] br-lan: port 2(wlan0) entered blocking state
[64988.809815] br-lan: port 2(wlan0) entered forwarding state
[72002.069094] conntrack: generic helper won't handle protocol 47. Please consider loading the specific helper module.


04.04.20202964Base systemBug ReportVery LowLowZyXEL Keenetic - USB port is not working in v18.06.2 an...TrunkUnconfirmed Task Description

Name the tree/revision/version:
OpenWrt v18.06.2 and later (tested v18.06.8, master at 1fb3c003d68d3feaf797e8b64edccc9fa622d250)

Name the affected device:
ZyXEL Keenetic

What does it not do that it should do:
USB port is not working.

Steps to reproduce:
1. Build and install OpenWrt v18.06.2 or later with appropriate kmods and their dependencies:
kmod-usb-dwc2
kmod-usb-storage
kmod-fs-vfat

2. Boot.

3. Insert a USB flash drive. There is no /dev/sd* device to mount, no new usb related messages in dmesg.
Just for test, plug in a USB optical mouse, LED does not light.

What you have already done to workaround/fix the problem:
On v18.06.1 USB works, files from the flash drive ara accessible, LED in USB optical mouse is on, corresponding dmesg messages appear.

Any additional info you think is important:
bootlogs with USB flash drive attached:
18.06.1-bootlog.txt - 18.06.1 (flashed)
18.06.2-bootlog.txt - 18.06.2 (initramfs-kernel loaded from tftp)
master-bootlog.txt - master (initramfs-kernel loaded from tftp)

patches to use full 8MB flash applied to install packages:
- to v18.06.x
https://patchwork.ozlabs.org/patch/1259802/ - to master
https://patchwork.ozlabs.org/patch/1262191/

04.04.20202963PackagesBug ReportVery LowLowAdd support for 4G Systems XSStick W1208AllUnconfirmed Task Description

Please add Support for this LTE Stick to the OpenWRT distribution.
The device shows up as

root@GL-MT300N:~# lsusb 
...
Bus 001 Device 003: ID 2fd4:76b5  
...
root@GL-MT300N:~# 

usbmode switch can be done via:

        "messages" : [
                "55534243a069008d8000000080000606f50402527100000000000000000000",
        ],
                "2fd4:9aff": {
                        "*": {
                                "t_vendor": 12244,
                                "t_product": 30389,
                                "msg": [ 0 ]
                        }       
                }

Afterwards missing is:

echo 0x2fd4 0x76b5 > /sys/bus/usb-serial/drivers/option1/new_id

The data was taken from https://www.draisberghof.de/usb_modeswitch/

04.04.20202962Base systemBug ReportVery LowVery LowGlobal section not createdTrunkWaiting on reporter Task Description

If I build on masters by disabling IPv6 support, the Globals section in “network” config file is not created.

- The problem occurs on Linksys WRT3200ACM (Rango), but I suppose it is independent of the hardware.
- I am currently building on master and this is where I noticed the problem.
- Download the code, update and install the packages, access menuconfig. Disable IPv6 support. Save the configuration, build and flash the

 firmware on the device. Check the file /etc/config/network.

Although the Globals section contains ula_prefix, it also contains packet_steering, which is not related to IPv6 support.
The workaround is to manually create the Globals section and add the option for packet_steering.

04.04.20202961PackagesBug ReportVery LowMediumRsyslog doesn't create spool nor disk-assisted queue fi...openwrt-19.07Unconfirmed Task Description

- Device problem occurs on

TP-Link TL-WR1043ND v2
TP-LINK TD-W8970

- Software versions of OpenWrt/LEDE release, packages, etc.

openwrt-19.07 branch git-20.093.48508-e2aaef6
rsyslogd 8.39.0

- Steps to reproduce
The first issue is that rsyslog doesn’t write to or create directories/files inside the /var/log directory beside the log files.
needed to create a work directory for spool and disk-assisted queue files.
using

$CreateDirs on

and

$WorkDirectory /var/log/rsyslog

I get

Apr  2 10:35:34 OpenWrt : $WorkDirectory: /var/log/rsyslog can not be accessed, probably does not exist - directive ignored [v8.39.0 try http://www.rsyslog.com/e/2181 ]

I created the directory manually and the error was gone but the directory remained empty even after disconnecting the log server for 24hrs, no spool files were created nor disk-assisted queue files were created either and as a result when connecting the server back after 24hrs the in-memory queue got sent to the server which equals roughly to 10min worth of logs while the WorkDirectory /var/log/rsyslog remained empty.

04-04-2020	10:32:45	Syslog.Error	192.168.1.1	Apr  4 08:22:19 OpenWrt : cannot connect to 192.168.1.100:514: Host is unreachable [v8.39.0 try http://www.rsyslog.com/e/2027 ]
04-04-2020	10:32:45	Syslog.Error	192.168.1.1	Apr  4 08:22:52 OpenWrt : cannot connect to 192.168.1.100:514: Host is unreachable [v8.39.0 try http://www.rsyslog.com/e/2027 ]
04-04-2020	10:32:45	Syslog.Error	192.168.1.1	Apr  4 08:23:25 OpenWrt : cannot connect to 192.168.1.100:514: Host is unreachable [v8.39.0 try http://www.rsyslog.com/e/2027 ]
04-04-2020	10:32:45	Syslog.Error	192.168.1.1	Apr  4 08:23:58 OpenWrt : cannot connect to 192.168.1.100:514: Host is unreachable [v8.39.0 try http://www.rsyslog.com/e/2027 ]
04-04-2020	10:32:45	Syslog.Error	192.168.1.1	Apr  4 08:24:32 OpenWrt : cannot connect to 192.168.1.100:514: Host is unreachable [v8.39.0 try http://www.rsyslog.com/e/2027 ]
04-04-2020	10:32:45	Syslog.Error	192.168.1.1	Apr  4 08:25:05 OpenWrt : cannot connect to 192.168.1.100:514: Host is unreachable [v8.39.0 try http://www.rsyslog.com/e/2027 ]
04-04-2020	10:32:45	Syslog.Error	192.168.1.1	Apr  4 08:25:38 OpenWrt : cannot connect to 192.168.1.100:514: Host is unreachable [v8.39.0 try http://www.rsyslog.com/e/2027 ]
04-04-2020	10:32:45	Syslog.Error	192.168.1.1	Apr  4 08:26:11 OpenWrt : cannot connect to 192.168.1.100:514: Host is unreachable [v8.39.0 try http://www.rsyslog.com/e/2027 ]
04-04-2020	10:32:45	Syslog.Error	192.168.1.1	Apr  4 08:26:44 OpenWrt : cannot connect to 192.168.1.100:514: Host is unreachable [v8.39.0 try http://www.rsyslog.com/e/2027 ]
04-04-2020	10:32:45	Syslog.Error	192.168.1.1	Apr  4 08:27:17 OpenWrt : cannot connect to 192.168.1.100:514: Host is unreachable [v8.39.0 try http://www.rsyslog.com/e/2027 ]
04-04-2020	10:32:45	Syslog.Error	192.168.1.1	Apr  4 08:27:50 OpenWrt : cannot connect to 192.168.1.100:514: Host is unreachable [v8.39.0 try http://www.rsyslog.com/e/2027 ]
04-04-2020	10:32:45	Syslog.Error	192.168.1.1	Apr  4 08:28:23 OpenWrt : cannot connect to 192.168.1.100:514: Host is unreachable [v8.39.0 try http://www.rsyslog.com/e/2027 ]
04-04-2020	10:32:45	Syslog.Error	192.168.1.1	Apr  4 08:28:57 OpenWrt : cannot connect to 192.168.1.100:514: Host is unreachable [v8.39.0 try http://www.rsyslog.com/e/2027 ]
04-04-2020	10:32:45	Syslog.Error	192.168.1.1	Apr  4 08:29:30 OpenWrt : cannot connect to 192.168.1.100:514: Host is unreachable [v8.39.0 try http://www.rsyslog.com/e/2027 ]
04-04-2020	10:32:45	Syslog.Info	192.168.1.1	Apr  4 08:29:45 OpenWrt : -- MARK --
04-04-2020	10:32:45	Syslog.Error	192.168.1.1	Apr  4 08:30:03 OpenWrt : cannot connect to 192.168.1.100:514: Host is unreachable [v8.39.0 try http://www.rsyslog.com/e/2027 ]
04-04-2020	10:32:45	Syslog.Error	192.168.1.1	Apr  4 08:30:36 OpenWrt : cannot connect to 192.168.1.100:514: Host is unreachable [v8.39.0 try http://www.rsyslog.com/e/2027 ]
04-04-2020	10:32:45	Syslog.Error	192.168.1.1	Apr  4 08:31:09 OpenWrt : cannot connect to 192.168.1.100:514: Host is unreachable [v8.39.0 try http://www.rsyslog.com/e/2027 ]
04-04-2020	10:32:45	Syslog.Error	192.168.1.1	Apr  4 08:31:42 OpenWrt : cannot connect to 192.168.1.100:514: Host is unreachable [v8.39.0 try http://www.rsyslog.com/e/2027 ]
04-04-2020	10:32:45	Syslog.Error	192.168.1.1	Apr  4 08:32:15 OpenWrt : cannot connect to 192.168.1.100:514: Host is unreachable [v8.39.0 try http://www.rsyslog.com/e/2027 ]
04-04-2020	10:32:45	Syslog.Info	192.168.1.1	Apr  4 08:32:45 OpenWrt : action 'action-13-builtin:omfwd' resumed (module 'builtin:omfwd') [v8.39.0 try http://www.rsyslog.com/e/2359 ]

even when using /var/log directly as a WorkDirectory the results remained the same.

The second issue is that for a work around I tried using the imfile module to access the log files directly without the need to disk-assisted queues but got this error

Apr  3 22:16:18 OpenWrt : could not load module 'imfile', errors: trying to load module /usr/lib/rsyslog/imfile.so: Error loading shared library /usr/lib/rsyslog/imfile.so: No such file or directory [v8.39.0 try http://www.rsyslog.com/e/2066 ]
04.04.20202959Base systemBug ReportVery LowLowkern.info kernel: do_page_fault(): sending SIGSEGV to u...TrunkUnconfirmed Task Description

Supply the following if possible:
- Device problem occurs on

ath79-generic-netgear_wndr3800

- Software versions of OpenWrt/LEDE release, packages, etc.

r12776-437eb41f23

libunbound-light - 1.10.0-2
unbound-control - 1.10.0-2
unbound-control-setup - 1.10.0-2
unbound-daemon - 1.10.0-2

Package: unbound-control
Version: 1.10.0-2
Depends: libc, libopenssl1.1, unbound-daemon
Status: install user installed
Section: net
Architecture: mips_24kc
Size: 45121
Filename: unbound-control_1.10.0-2_mips_24kc.ipk
Description: This package contains the Unbound control utility.
Installed-Time: 1585766447

- Steps to reproduce

 

Initially posted at forum.openwrt.org
https://forum.openwrt.org/t/unbound-control-1-10-0-2-sending-sigsegv-to-unbound-control-for-invalid-read-access-from-00000000/59201

Then posted on github, but I can’t seem to locate unbound-control code, especially 1.10.0.2, there:
https://github.com/openwrt/packages/issues/11750

On the CLI, when issuing for example “unbound-control local-data test.lan A 10.10.10.10”, it manifests itself as:

[1585965988] unbound-control[32619:0] warning: control-enable is ‘no’ in the config file.
Segmentation fault

In syslog, it shows:

Wed Apr 1 12:01:38 2020 kern.info kernel: [141571.460081] do_page_fault(): sending SIGSEGV to unbound-control for invalid read access from 00000000
Wed Apr 1 12:01:38 2020 kern.info kernel: [141571.474976] ra = 77df0d2d in libunbound.so.8.1.7[77dbc000+b3000]

Now, I’m getting a bit more info in syslog, when unbound-control gets triggered by a shell script, specifically that line referencing libc:

Thu Apr 2 22:01:55 2020 kern.info kernel: [253187.975857] do_page_fault(): sending SIGSEGV to unbound-control for invalid read access from 00000000
Thu Apr 2 22:01:55 2020 kern.info kernel: [253187.985262] epc = 77eca230 in libc.so[77e56000+97000]
Thu Apr 2 22:01:55 2020 kern.info kernel: [253187.990544] ra = 77dd2d2d in libunbound.so.8.1.7[77d9e000+b3000]
Thu Apr 2 22:01:55 2020 local0.warn dnsmasq[6451]: script process exited with status 139

03.04.20202957ToolchainBug ReportVery LowMediumopenwrt 19.07 x86_64 sdk toolchain segmentation fault i...openwrt-19.07Unconfirmed Task Description

Hi guys:

I found that the toolchain of openwrt 19.07 has some issues on x86_64 platform.

For example:
1. I use this sdk to build openwrt-shadowsocks 2. Install the compiled ipk, run the command `ss-local`, will report a `segmentation fault` error.

This error only occurs on openwrt 19.07 x86_64 platform. 19.07 toolchain on other platforms does not have this error, and the 18.06 version of the toolchain on the x86_64 platform also has no such errors.

01.04.20202956KernelBug ReportVery LowMediumtcp_bbr: suffering poor performance with samba4-serveropenwrt-19.07Unconfirmed Task Description

Environment: Newifi-D2(arch mipsel_24kc), OpenWrt 19.07.1/19.07.2/master branch with kernel 1.14.170+, samba-4.11, a usb-disk with ext4 file system.
(samba4 uses default settings)

I run samba-4.11 server in my router with usb-harddisk of 3T volumes. If the router enables tcp_bbr kernel module with default config file, then lan PCs copying files from the router is very slowly with speed of 4-10MB. The speed of writing files to router’s share is also a little slower.
Without tcp_bbr the speed is up to 40-60MB when copying files from the router.

I found the problem is caused by lack value of “net.core.default_qdisc=fq” in default bbr config file (/etc/sysctl.d/12-tcp-bbr.conf)
The default bbr config file is :
```
# Do not edit, changes to this file will be lost on upgrades
# /etc/sysctl.conf can be used to customize sysctl settings

net.ipv4.tcp_congestion_control=bbr
net.core.default_qdisc=fq #add this line then problem disappear.
```


31.03.20202951Base systemBug ReportVery LowMediumx86_64 ext4 generic: online resizing of root partition ...TrunkUnconfirmed Task Description

Used HW/SW:

- PCEngines APU2C4
- OpenWrt SNAPSHOT, r12776-437eb41f23

Steps to reproduce:

- Install needed packages:

root@OpenWrt:~# opkg update && opkg install fdisk resize2fs

- Extend root partition from 104 MB to 256 MB with fdisk:

root@OpenWrt:~# fdisk /dev/mmcblk0 << EOF
p
d
2
n
p
2
33792
+256M

w
EOF

- Extend ext4 filesystem:

root@OpenWrt:~# resize2fs /dev/mmcblk0p2

Here are the output of resize2fs:

root@OpenWrt:~# resize2fs /dev/mmcblk0p2 
resize2fs 1.45.4 (23-Sep-2019)
Filesystem at /dev/mmcblk0p2 is mounted on /; on-line resizing required
old_desc_blocks = 1, new_desc_blocks = 1
Performing an on-line resize of /dev/mmcblk0p2 to 65664 (4k) blocks.
resize2fs: Invalid argument While trying to add group #1

Here are the dmesg output:

root@OpenWrt:~# dmesg | tail -n 6
[50698.949591] EXT4-fs (mmcblk0p2): resizing filesystem from 32768 to 65664 blocks
[50698.957030] EXT4-fs (mmcblk0p2): resizing filesystem from 32768 to 65536 blocks
[50698.969299] EXT4-fs warning (device mmcblk0p2): reserve_backup_gdb:1033: reserved block 8 not at offset 7
[50698.978959] EXT4-fs warning (device mmcblk0p2): ext4_resize_fs:2120: error (-22) occurred during file system resize
[50698.989429] EXT4-fs (mmcblk0p2): resized filesystem to 32768
[50698.999227] EXT4-fs warning (device mmcblk0p2): reserve_backup_gdb:1033: reserved block 8 not at offset 7

Offline resizing does work as expected.

30.03.20202949KernelBug ReportVery LowHighWireless not working on bananapi proopenwrt-19.07Assigned Task Description

openwrt install on bananapi pro has no functioning wifi.
No wireless interface, no wireless option in ui, etc...

Supply the following if possible:
- Device problem occurs on: lemaker bananapi pro
- Software versions of OpenWrt/LEDE release, packages, etc. : openwrt-19.07.2 and also 18.06.8
- Steps to reproduce

 flash openwrt to sd card
 boot
 check interfaces via the UI or SSH

I’ve attached syslog & dmesg

suspicious lines:
[ 9.150351] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43362-sdio for chip BCM43362/1
[ 9.159364] brcmfmac mmc1:0001:1: Direct firmware load for brcm/brcmfmac43362-sdio.bin failed with error -2
[ 9.169181] brcmfmac mmc1:0001:1: Falling back to user helper
[ 9.222013] firmware brcm!brcmfmac43362-sdio.bin: firmware_loading_store: map pages failed

Might be relevant:
https://github.com/armbian/build/commit/1c3fde7d3b8f97a7acbd41d5513d73990e3c77e9 https://forum.armbian.com/topic/9341-brcmfmac-not-working-after-upgrade-to-armbian-570/

29.03.20202943KernelBug ReportVery LowMediumKernel panic with dev_net(skb->dev)==NULL in nf_xfrm_me...AllUnconfirmed Task Description

Hi, I have some questions regarding debugging of random reboot problem caused by kernel panic.

I’m getting random reboot when running a software inserting prerouting iptables rules in order to redirect traffic. My device is a x86_64 router. My openwrt release is compiled by myself from a forked openwrt source at https://github.com/coolsnowwolf/lede . Its kernel version is 4.19.108.

The software causing this problem is called OpenClash. It acts as a transparent proxy. It inserts prerouting rules to redirect all tcp traffic from computers in LAN to its own listening port and sends the traffic through a proxy.

Whenever this software is started, I get random reboots at 1-2 times/day. There was not any abnormal in saved log files because the crash happend in kernel and it caused reboot quickly. So I had to compile the NetConsole kernel module to capture the dmesg when crash happened. You can see the crash logs in crash_dmesg.txt.

The crash happens in the `nf_xfrm_me_harder` function. Decompiling the crash code, I get crash_code.png (The highlighted line is the crash instruction). The crash log mentions illegal memory access at 000000000000113c and the crash code shows that the kernel was accessing [rax+0x113c], so I think the problem is rax==0, which should not be happening.

The source code causing crash actually locates in a patch, which is also included in trunk OpenWrt: https://github.com/openwrt/openwrt/blob/master/target/linux/generic/pending-4.19/616-net_optimize_xfrm_calls.patch

After patched, function `nf_xfrm_me_harder` looks like

int nf_xfrm_me_harder(struct net *net, struct sk_buff *skb, unsigned int family)
{
        struct flowi fl;
        unsigned int hh_len;
        struct dst_entry *dst;
        struct sock *sk = skb->sk;
        int err;

        if (skb->dev && !dev_net(skb->dev)->xfrm.policy_count[XFRM_POLICY_OUT]) // <-------crash
                return 0;

        err = xfrm_decode_session(skb, &fl, family);
        if (err < 0)
                return err;

This means

dev_net(skb->dev)

sometimes equals to `NULL` .

I’m not familiar with the network mechanism in linux kernel, so I’m not sure how I can find the reason of it being NULL. Is this problem something we can safely ignore by checking its validity like this?

if (skb->dev && dev_net(skb->dev) && !dev_net(skb->dev)->xfrm.policy_count[XFRM_POLICY_OUT])

If not, can anyone give me some advice on how I can debug this problem? I understand this may be difficult for you developers to figure out what’s happening by merely reading my description, especially when I’m not using the trunk OpenWrt. So I would love to dig it by myself.

You can see other information of my router in dmesg.txt.

Thanks a lot.

27.03.20202940KernelBug ReportVery LowLowKernel uImage end up being non compressed - error in pa...TrunkUnconfirmed Task Description

- Device problem occurs on: My Book Live - platform apm821xx
- Software versions of OpenWrt/LEDE release, packages, etc. : trunk, kernel 5.4
- Steps to reproduce: simply build the kernel

 

The patch https://github.com/openwrt/openwrt/blob/master/target/linux/apm821xx/patches-5.4/900-powerpc-bootwrapper-force-gzip-as-mkimage-s-compress.patch does not seem to work for me and results in an uncompressed uImage.

I believe the issue is this line of the patch: cmd_wrap =$(CONFIG_SHELL) $(wrapper) -Z gzip -c -o $@ -p $2 \
Works if changed to cmd_wrap =$(CONFIG_SHELL) $(wrapper) -Z gz -c -o $@ -p $2 \ or alternatively cmd_wrap =$(CONFIG_SHELL) $(wrapper) -z -c -o $@ -p $2 \

This patch seems to be a workaround for a change in the kernel configuration from:
CONFIG_KERNEL_GZIP=y
# CONFIG_KERNEL_XZ is not set
To
# CONFIG_KERNEL_GZIP is not set
CONFIG_KERNEL_XZ=y

Maybe this change is not needed...

PS. I maintain custom kernels for the My Book Live platform @ ftp://https://github.com/ewaldc/My-Book-Live, specifically tuning the networking, DMA and SATA drivers, as well as SAMBA.
I admire all the work from the OpenWrt team (Christian in particular) and I am always willing to help and test.
Regards,
Ewald.


27.03.20202939KernelBug ReportVery LowHighgpio-button-hotplug compilation errorTrunkUnconfirmed Task Description
make[3]: Entering directory '/home/sda3/openwrt/build_dir/target-x86_64_musl/linux-x86_64/linux-5.4.24'
make[4]: *** No rule to make target '/home/sda3/openwrt/build_dir/target-x86_64_musl/linux-x86_64/gpio-button-hotplug/gpio-button-hotplug.o', needed by '__build'.  Stop.
Makefile:1691: recipe for target '/home/sda3/openwrt/build_dir/target-x86_64_musl/linux-x86_64/gpio-button-hotplug' failed
make[3]: *** [/home/sda3/openwrt/build_dir/target-x86_64_musl/linux-x86_64/gpio-button-hotplug] Error 2


27.03.20202936DocumentationBug ReportVery LowHighDocumentation for Pogoplug results in brickTrunkUnconfirmed Task Description

[1] assumes that u-boot image is smaller than 512 KB, but this is no longer the case. Followed the instructions without a second thought and bricked my device. It could have used ${filesize} like the sections below it, or simply use 640 KiB instead of 512 KiB. (The 660 KiB in the section might be a typo, it is not multiple of 128 KiB)

Besides, links in [2] are mostly broken and outdated. In addition, for V4 A3 devices, there are no test pads for JTAG.

[1] https://openwrt.org/toh/cloudengines/pogoplug#single-stage_bootloader [2] https://openwrt.org/toh/cloudengines/pogo-v4

26.03.20202935Base systemBuild FailureVery LowCriticalx86/geode: cycling reboot with openwrt-x86-geode-gener...TrunkAssigned Task Description

Device problem occurs on booting

[    2.744573] F2FS-fs (sda2): Magic Mismatch, valid(0xf2f52010) - read(0x803646e3)
[    2.752130] F2FS-fs (sda2): Can't find valid F2FS filesystem in 1th superblock
[    2.762100] F2FS-fs (sda2): Magic Mismatch, valid(0xf2f52010) - read(0xd083295c)
[    2.769648] F2FS-fs (sda2): Can't find valid F2FS filesystem in 2th superblock
[    2.777149] List of all partitions:
[    2.780684] 0800           64000 sda
[    2.780689]  driver: sd
[    2.786951]   0801            8192 sda1 d50cf6e8-01
[    2.786955]
[    2.793377]   0802           55296 sda2 d50cf6e8-02
[    2.793380]
[    2.799893] No filesystem could mount root, tried:
[    2.799896]  ext3
[    2.804794]  ext2
[    2.806834]  ext4
[    2.808783]  squashfs
[    2.810733]  f2fs
[    2.813031]
[    2.816579] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-                                                                                                                  block(8,2)
[    2.824874] Kernel Offset: disabled
[    2.828394] Rebooting in 1 seconds..

Software versions of OpenWrt/LEDE release, packages, etc.
nightbuild image @2020-03-26 r12712-556b858

Steps to reproduce
After syncronizing source code with master branch we get fail with x86-*squashfs-combined images.
Size of openwrt-x86-geode-generic-squashfs-combined.img and openwrt-x86-geode-geos-squashfs-combined.img images isn’t
correct (less than expected).
Device never boot with them.

26.03.20202931Base systemBug ReportVery LowHighloading package information never arrivedopenwrt-19.07Unconfirmed Task Description

using fresh install

from Luci interface goto menu
system/software
the loading package information never arrived

pushing the update list button
the loading package information never arrived

using the console
opk update, list... are working well


25.03.20202928Base systemBug ReportVery LowHighTP-Link TL-WDR3600 v1 on kernel 5.4 boot-loops since ch...TrunkUnconfirmed Task Description

- Device problem occurs on

TP-Link TL-WDR3600 v1

- Software versions of OpenWrt/LEDE release, packages, etc.

Since reboot-12646-gdb70077668 “toolchain: Update GCC 8 to version 8.4.0” and kernel 5.4, WDR3600 boot-loops with the following message:

Starting kernel ...

[    0.000000] Linux version 5.4.24 (openwrt@hawg) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r12683-8c33debb52)) #0 Sat Mar 21 21:35:45 2020
[    0.000000] printk: bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 0001974c (MIPS 74Kc)
[    0.000000] MIPS: machine is TP-Link TL-WDR3600 v1
[    0.000000] SoC: Atheros AR9344 rev 2
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32480
[    0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 122384K/131072K available (4681K kernel code, 187K rwdata, 1080K rodata, 1212K init, 196K bss, 8688K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS: 51
[    0.000000] random: get_random_bytes called from start_kernel+0x32c/0x51c with crng_init=0
[    0.000000] CPU clock: 560.000 MHz
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6825930166 ns
[    0.000009] sched_clock: 32 bits at 280MHz, resolution 3ns, wraps every 7669584382ns
[    0.008305] Calibrating delay loop... 278.93 BogoMIPS (lpj=1394688)
[    0.084927] pid_max: default: 32768 minimum: 301
[    0.089999] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.097796] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.107070] Kernel panic - not syncing: Unexpected DSP exception
[    0.113470] Rebooting in 1 seconds..
24.03.20202926PackagesBug ReportVery LowLowbusybox: less: search doesn't workopenwrt-18.06Unconfirmed Task Description

Steps to reproduce:
Open any text file in less and press “/” or “?” key to start search.

It does nothing on OpenWRT, which is very unfortunate...

 


24.03.20202925KernelBug ReportVery LowMediumsdc_busy timeout: before CMD<55> <- msdc_command_start(...openwrt-19.07Unconfirmed Task Description

Supply the following if possible:
- Device problem occurs on:
Architecture: MediaTek MT7621 ver:1 eco:3
Model: MTC Wireless Router WR1201
Router brand: Strong 1200
- Software versions of OpenWrt/LEDE release, packages, etc.:
OpenWrt 19.07.0 r10860-a3ffeb413b / LuCI openwrt-19.07 branch git-20.006.26738-35aa527
Packages installed:
kmod-mmc 4.14.162-1
kmod-sdhci-mt7620 4.14.162-1
kmod-mt76-core 4.14.162+2020-01-04-8a785679-1
kmod-usb-core 4.14.162-1
kmod-usb3 4.14.162-1
Kernel 4.14.162
- Steps to reproduce

Problem is that microSD card is not recognized. After inserting the microsd card this is shown in logs. I try three vendors. example brand new SanDisk microSDHC 32 GB Ultra Class 10 UHS-I
[ 1763.831968] msdc0 → XXX sdc_busy timeout: before CMD<55> ← msdc_command_start() : L<860> PID<kworker/0:1><0×39>
[ 1763.852517] mmc0: error -145 whilst initialising SD card
[ 1764.131968] msdc0 → XXX sdc_busy timeout: before CMD<55> ← msdc_command_start() : L<860> PID<kworker/0:1><0×39>
[ 1764.152467] mmc0: error -145 whilst initialising SD card
[ 1764.431965] msdc0 → XXX sdc_busy timeout: before CMD<55> ← msdc_command_start() : L<860> PID<kworker/0:1><0×39>
[ 1764.452549] mmc0: error -145 whilst initialising SD card

 


23.03.20202923Base systemBug ReportVery LowLowwlan country code not applied unless interface is enabl...TrunkUnconfirmed Task Description

This true since version 18 and still true in version 19
Is probabbly generic. Seen on two different HW CF-E110 and WT3020)

Starting from a fresh install
Goto Network\wireless ⇒ the interface is disabled by default
Enter to edit the wireless interface

 Look at the possible channels, it is 1 to 11 (normal as the default country code is world)  

Goto Network\wireless - Device configuration\Advanced Settings

 Change the Country code from 00-World to FR-France

Validate the change by Save and Apply
Enter to edit the wireless interface (while the interface is still disabled)

 Look at the possible channels, it is still 1 to 11 (while the country code is FR)

We shall normally access to channel 1 to 13 with FR code.

Look like save and apply only saves and donnot apply the country code selection
But If you enable the interface, this allow the access to channels 1 to 13

23.03.20202922Base systemBug ReportVery LowHighNo COMFAST CF-E110NV2 8MB flash compatible versionTrunkUnconfirmed Task Description

CF-E110V2 is released with 8MB Flash (maybe it was before with 16 but apparently no longer, see forum discussions on CF-E110)
The current released package is only for 16MB flash

Can You generate and publicly release a 8MB flash compatible version too.

Hereafter the modified part of the dts file I’m using to compile my own FW (based on original OEM partition table).

flash@0 {
	compatible = "winbond,w25q64", "jedec,spi-nor";
	reg = <0>;
	spi-max-frequency = <25000000>;
	partitions {
		compatible = "fixed-partitions";
		#address-cells = <1>;
		#size-cells = <1>;
		partition@0 {
			label = "u-boot";
			reg = <0x000000 0x010000>;
			read-only;
		};
		art: partition@10000 {
			label = "art";
			reg = <0x010000 0x010000>;
			read-only;
		};
		partition@20000 {
			compatible = "denx,uimage";
			label = "firmware";
			reg = <0x020000 0x7d0000>;
		};
		partition@7f0000 {
			label = "nvram";
			reg = <0x7f0000 0x010000>;
			read-only;
		};
	};
};
 


Showing tasks 101 - 150 of 1138 Page 3 of 23 - 1 - 2 - 3 - 4 - 5 - Last >>

Available keyboard shortcuts

Tasklist

Task Details

Task Editing