OpenWrt/LEDE Project

Welcome to the OpenWrt/LEDE Project bug reporting and issue tracking system

Problems to be reported here are for the OpenWrt/LEDE Project targets, sources, toolchain, core packages, build procedures, distribution and infrastructure. Guidelines for submitting a good bug report can be found at the OpenWrt/LEDE Project website. Problems related to LuCI or OpenWrt packages need to be reported in their repositories:

Notifications of all submissions and task changes are sent to lede-bugs@infradead.org.

OpenedIDCategoryTask TypePrioritySeveritySummaryReported InStatus
27.10.2016253Base systemBug ReportVery LowHighMulticast over wireless ceases to work properly after a...AllNew Task Description

I am having a problem on a UBNT UAP-LR where, if many clients stay connected the router for a long time, multicast packets will stop being reliably sent to the wireless clients. I can reproduce this with LEDE r1953, but it goes back at least as far as OpenWRT 15.05.1 with kernel 3.18. I can not, however, reproduce it on another network with the same WAP but with only one or two wireless clients.

This originally manifested as IPv6 ceasing to work since the (multicasted) RA packets were not reaching the wireless clients. I used tcpdump on the WAP and determined that the RAs were arriving through the wired interface and leaving through the wireless interface as they should, but tcpdump on the client indicates that a vast majority of the RAs are never received. (Please note that the IPv6 issue is not reproducible with the router running OpenWRT/LEDE and odhcpd, since odhcpd unicasts RAs sent as a response to an RS instead of multicasting them, while it is reproducible when the router is running radvd, for example as pfSense does.)

13.10.2016224Base systemBug ReportVery LowLowwrong source IP when logging to remote IPv6 syslog serv...TrunkAssigned Task Description

Hello,

I’m trying to send log to remote IPv6 syslog server (x:y:z:12::1), but packets received by syslog server are invalid. Instead of public IPv6 address, syslog udp packets are sent with ::1 source IP and therefore ignored by destination server. Logging over IPv4 works ok.

tcpdump log from destination syslog server:
23:34:16.988433 IP6 ::1.38044 > x:y:z:12::1.514: SYSLOG daemon.notice, length: 65

Configuration:

/etc/config/system:

 option log_ip 'x:y:z:12::1'

Device is in the same range as syslog server (x:y:z:12::119/64) and has native IPv6 connectivity. Other services (dropbear, ntp client, snmpd, luci) are running fine over IPv6.

Device is TP-Link WDR3600, running lede reboot-1818-gb81fc29.

12.10.2016222Base systemFeature RequestVery LowLowproviding pre-built images for extroot for devices with...TrunkUnconfirmed Task Description

Currently, the only way to be able to make extroot (use an external drive as overlay) for 4MiB devices is to build an image with the Image Builder as they can’t fit the packages needed in the jffs.

For most linux users this isn’t a major issue as the Image Builder runs on Linux and with a couple commands you build all, but it’s still time-consuming.

For everyone else this is an issue, as they need to get a linux system, learn how to use the Image Builder, and so on.

I’m asking if it is possible to make pre-built images with the right packages to allow extroot on 4 MiB devices.

The packages I thing we need in these pre-built images are all is needed by the device to be able to format and check its own drive, because again most users don’t have access to a linux system to format a drive with ext4 or whatever.

It seems e2fsprogs is too big to fit with the other packages required, currently only f2fs filesystem tools are split and can be used in 4MiB devices for extroot.

These are the packages that currently should allow building an extrootable image that fits on 4MiB storage:

blkid block-mount kmod-fs-f2fs kmod-usb-storage kmod-usb-uhci kmod-usb-ohci mkf2fs f2fsck

(of course no luci is included).

17.09.2016181Base systemBug ReportVery LowMediumChanging TX power doesn't nothing (MediaTek MT7628AN ve...TrunkUnconfirmed Task Description

Hello,

As I said, if I change the TX power from 0 dBm to 20 dBm doesn’t nothing. There isn’t any visible change in tx power. I tested other powers too (5, 8, 15,..).

It is a Xiaomi Nano (lite).

SoC Type: MediaTek MT7628AN ver:1 eco:2
MIPS: machine is MiWiFi Nano
Linux version 4.4.19 (-) (gcc version 5.4.0 (LEDE GCC 5.4.0 r1444) ) #0 Fri Aug 26 15:03:40 2016.

07.09.2016162Base systemBug ReportVery LowLowTwo issues with libuclient-openssl in luci-sslTrunkUnconfirmed Task Description

1: RC4 and 3DES are used when both have security issues. Actually the latter also is true of mbedtls/polarssl.

2: Only TLS 1.2 is supported. This makes multiple clients unable to connect.

BTW, I got this working after modifying the Makefile to luci-ssl to depend on libustream-openssl instead. No idea what the situation is but so far it works without a problem.

05.09.2016160Base systemBug ReportVery LowLowusb-serial (pl2303) failures on mt7621 dlink dir860l-b1TrunkUnconfirmed Task Description
git describe
reboot-1497-ga810e77

with diffconfig:

CONFIG_TARGET_ramips=y
CONFIG_TARGET_ramips_mt7621=y
CONFIG_TARGET_ramips_mt7621_DEVICE_dir-860l-b1=y
CONFIG_DEVEL=y
CONFIG_BUILD_LOG=y
CONFIG_PACKAGE_ip=y
CONFIG_PACKAGE_kmod-usb-core=y
CONFIG_PACKAGE_kmod-usb-ohci=y
CONFIG_PACKAGE_kmod-usb-ohci-pci=y
CONFIG_PACKAGE_kmod-usb-serial=y
CONFIG_PACKAGE_kmod-usb-serial-ftdi=y
CONFIG_PACKAGE_kmod-usb-serial-pl2303=y
CONFIG_PACKAGE_kmod-usb2=y
CONFIG_PACKAGE_kmod-usb2-pci=y
CONFIG_PACKAGE_kmod-usb3=y
CONFIG_PACKAGE_screen=y

screen starts, but doesn’t work. The usb-relevant dmesg’s are:

[    4.550000] usbcore: registered new interface driver usbfs
[    4.560000] usbcore: registered new interface driver hub
[    4.570000] usbcore: registered new device driver usb
[    4.580000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    4.620000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    4.670000] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 1
[    4.720000] hub 1-0:1.0: USB hub found
[    4.740000] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 2
[    4.760000] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[    4.770000] hub 2-0:1.0: USB hub found
[    5.260000] usb 1-1: new full-speed USB device number 2 using xhci-mtk
[    5.410000] usb 1-1: no of_node; not parsing pinctrl DT
[   10.150000] usbcore: registered new interface driver usbserial
[   10.160000] usbcore: registered new interface driver usbserial_generic
[   10.180000] usbserial: USB Serial support registered for generic
[   10.220000] usbcore: registered new interface driver ftdi_sio
[   10.240000] usbserial: USB Serial support registered for FTDI USB Serial Device
[   10.260000] usbcore: registered new interface driver pl2303
[   10.270000] usbserial: USB Serial support registered for pl2303
[   10.290000] pl2303 ttyUSB0: no of_node; not parsing pinctrl DT
[   10.290000] usb 1-1: pl2303 converter now attached to ttyUSB0
[  871.510000] pl2303 ttyUSB0: pl2303_get_line_request - failed: -145
[  871.620000] pl2303 ttyUSB0: pl2303_set_line_request - failed: -145
[  871.840000] pl2303 ttyUSB0: pl2303_set_control_lines - failed: -145

Screen also throws an error (which gets blanked out, but is captured by the serial console):

# screen /dev/ttyUSB0 115200
/dev/null/utmp: Not a directory
02.09.2016133Base systemBug ReportVery LowLowNetgear r8000 cannot use 802.1x encryptionTrunkUnconfirmed Task Description

Github issue #305 reported by https://github.com/Halry

My android phone can’t connect to it.(tested on nexus 6p and samsung s7 edge)
Sun Aug 28 16:28:46 2016 daemon.debug hostapd: wlan2: STA 94:fe:22:11:22:33 IEEE 802.1X: Sending EAP Packet (identifier 247)
Sun Aug 28 16:28:46 2016 daemon.debug hostapd: wlan2: STA 94:fe:22:11:22:33 WPA: sending 1/4 msg of 4-Way Handshake
Sun Aug 28 16:28:46 2016 daemon.debug hostapd: wlan2: STA 94:fe:22:11:22:33 WPA: received EAPOL-Key frame (2/4 Pairwise)
Sun Aug 28 16:28:46 2016 daemon.debug hostapd: wlan2: STA 94:fe:22:11:22:33 WPA: sending 3/4 msg of 4-Way Handshake
Sun Aug 28 16:28:46 2016 daemon.info hostapd: wlan2: STA 94:fe:22:11:22:33 IEEE 802.11: disassociated
Sun Aug 28 16:28:46 2016 daemon.debug hostapd: wlan2: STA 94:fe:22:11:22:33 WPA: event 2 notification
Sun Aug 28 16:29:00 2016 daemon.info hostapd: wlan1: STA 94:fe:22:11:22:33 IEEE 802.11: associated
Sun Aug 28 16:29:00 2016 daemon.info hostapd: wlan1: STA 94:fe:22:11:22:33 IEEE 802.11: disassociated
Sun Aug 28 16:29:11 2016 daemon.info hostapd: wlan1: STA 94:fe:22:11:22:33 IEEE 802.11: associated
Sun Aug 28 16:29:11 2016 daemon.info hostapd: wlan1: STA 94:fe:22:11:22:33 IEEE 802.11: disassociated

However,Windows can connect to it.

Here are some my nexus 6p’s dmesg:
CFG80211-ERROR wl_cfg80211_disconnect:Reason 17

30.08.2016126KernelBug ReportVery LowMediumkernel panic on brcm47xx (netgear wgt634u) when routing...TrunkUnconfirmed Task Description

With LEDE version reboot-1444-g1bb914d, when pulling data through the WAN interface to the LAN interface at a sufficiently high speed, e.g. on a Raspberry Pi connected by ethernet to a LAN port, and the WAN interface connected to a gigabit internet service and issuing a command like:

curl https://cdn.kernel.org/pub/linux/kernel/v4.x/linux-4.7.2.tar.xz > /dev/null

From the pi, I see something like:

  % Total    % Received % Xferd  Average Speed   Time    Time     Time  Current
                                 Dload  Upload   Total   Spent    Left  Speed
  9 86.2M    9 7977k    0     0  1834k      0  0:00:48  0:00:04  0:00:44 1835k[  352.295252] smsc95xx 1-1.1:1.0 eth0: link down
  9 86.2M    9 7977k    0     0  1255k      0  0:01:10  0:00:06  0:01:04 1155k[  353.959380] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
  9 86.2M    9 7977k    0     0  43292      0  0:34:48  0:03:08  0:31:40     0

or

  % Total    % Received % Xferd  Average Speed   Time    Time     Time  Current
                                 Dload  Upload   Total   Spent    Left  Speed
  8 86.2M    8 7440k    0     0  1478k      0  0:00:59  0:00:05  0:00:54 1478k[ 1100.164849] smsc95xx 1-1.1:1.0 eth0: link down
  8 86.2M    8 7440k    0     0  1232k      0  0:01:11  0:00:06  0:01:05 1300k[ 1101.836954] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
  8 86.2M    8 7440k    0     0   740k      0  0:01:59  0:00:10  0:01:49     0

Where the “link down” is the WGT634U panic’ing and rebooting. The panic on the WGT634U looks like this:

[  171.966841] CPU 0 Unable to handle kernel paging request at virtual address 008224d8, epc == 80077ecc, ra == 801d8100
[  171.977700] Oops[#1]:
[  171.980093] CPU: 0 PID: 3 Comm: ksoftirqd/0 Not tainted 4.1.20 #0
[  171.986265] task: 8181e008 ti: 8182a000 task.ti: 8182a000
[  171.991711] $ 0   : 00000000 1000b800 008224d8 b41c479b
[  171.997140] $ 4   : 008224d8 00010000 80361ef8 00000000
[  172.002557] $ 8   : 81018b14 8101da14 00100100 dceb27b8
[  172.007983] $12   : ffffffff 00000001 ffffff80 000042c6
[  172.013400] $16   : b41c479b 00000001 81b450a8 81b7d260
[  172.018817] $20   : 803b5dcc 00000002 00000008 0000000a
[  172.024235] $24   : 00000000 80072b24                  
[  172.029653] $28   : 8182a000 8182bdb8 00000100 801d8100
[  172.035083] Hi    : 00000000
[  172.038026] Lo    : 0000006c
[  172.041036] epc   : 80077ecc put_compound_page+0x78/0x240
[  172.046547] ra    : 801d8100 skb_release_data+0xa8/0x10c
[  172.051920] Status: 1000b803 KERNEL EXL IE 
[  172.056254] Cause : 00800008
[  172.059194] BadVA : 008224d8
[  172.062144] PrId  : 00029007 (Broadcom BMIPS3300)
[  172.066891] Modules linked in: pppoe ppp_async iptable_nat ath5k ath pppox ppp_generic nf_nat_ipv4 nf_conntrack_ipv6 nf_conntrack_ipv4 mac80211 ipt_REJECT ipt_MASQUERADE cfg80211 xt_time xt_tcpudp xt_state xt_nat xt_multiport xt_mark xt_mac xt_limit xt_id xt_conntrack xt_comment xt_TCPMSS xt_REDIRECT xt_LOG xt_CT slhc nf_reject_ipv4 nf_nat_redirect nf_nat_masquerade_ipv4 nf_nat nf_log_ipv4 nf_defrag_ipv6 nf_defrag_ipv4 nf_conntrack_rtcache nf_conntrack iptable_raw iptable_mangle iptable_filter ip_tables crc_ccitt compat ip6t_REJECT nf_reject_ipv6 nf_log_ipv6 nf_log_common ip6table_raw ip6table_mangle ip6table_filter ip6_tables x_tables leds_gpio ehci_platform ehci_hcd gpio_button_hotplug usbcore nls_base usb_common ssb_hcd
[  172.132913] Process ksoftirqd/0 (pid: 3, threadinfo=8182a000, task=8181e008, tls=00000000)
[  172.141213] Stack : 1000b803 00000000 0000006c b41c479b 81b45080 801d8100 00000000 0000012c
          00000001 801e7d60 81becb60 81b7d260 81b7d260 80335b3c 81bece60 801d818c
          80360000 803623e0 81becb60 80335b3c 803623e0 801e63d8 8182be10 8182be10
          00000001 00000002 803b5dd0 00000001 803b5dd4 00000003 803b0000 80024fec
          81841048 80361100 819bb770 80007664 80364510 8181e008 80362898 04208040
          ...
[  172.178058] Call Trace:
[  172.180640] [<80077ecc>] put_compound_page+0x78/0x240
[  172.185822] [<801d8100>] skb_release_data+0xa8/0x10c
[  172.190895] [<801d818c>] __kfree_skb+0x28/0xb4
[  172.195466] [<801e63d8>] net_tx_action+0xd8/0x140
[  172.200329] [<80024fec>] __do_softirq+0x184/0x2b0
[  172.205184] [<80025140>] run_ksoftirqd+0x28/0x80
[  172.209953] [<8003bae0>] smpboot_thread_fn+0x148/0x178
[  172.215246] [<80039390>] kthread+0xdc/0xe8
[  172.219459] [<800010a8>] ret_from_kernel_thread+0x14/0x1c
[  172.224921] 
[  172.226470] 
Code: 30840001  0204100a  00402021 <8c420000> 000211c2  30420001  10400018  00000000  8e020000 
[  172.237022] ---[ end trace 89a3318b662df6d8 ]---
[  172.250536] Kernel panic - not syncing: Fatal exception in interrupt
[  172.262338] Rebooting in 3 seconds..

or

[ 1317.958261] Unhandled kernel unaligned access[#1]:
[ 1317.963173] CPU: 0 PID: 3 Comm: ksoftirqd/0 Not tainted 4.1.20 #0
[ 1317.969349] task: 8181e008 ti: 8182a000 task.ti: 8182a000
[ 1317.974795] $ 0   : 00000000 1000b801 00000001 00200000
[ 1317.980232] $ 4   : 647b394a 00010000 00018da4 00000000
[ 1317.985658] $ 8   : 8181e040 b1e1b104 00000017 40000000
[ 1317.991085] $12   : 500018dd 00000000 00000000 010102f2
[ 1317.996510] $16   : 80e4d1e0 00000001 80e4d208 81acb0e0
[ 1318.001936] $20   : 803b5dcc 00000002 00000008 0000000a
[ 1318.007362] $24   : 00000010 8001ead0                  
[ 1318.012789] $28   : 8182a000 8182bdd0 00000100 801d8100
[ 1318.018220] Hi    : 00000001
[ 1318.021160] Lo    : 00000001
[ 1318.024169] epc   : 80078474 put_page+0x0/0x4c
[ 1318.028732] ra    : 801d8100 skb_release_data+0xa8/0x10c
[ 1318.034104] Status: 1000b803 KERNEL EXL IE 
[ 1318.038439] Cause : 00800010
[ 1318.041380] BadVA : 647b394a
[ 1318.044330] PrId  : 00029007 (Broadcom BMIPS3300)
[ 1318.049076] Modules linked in: pppoe ppp_async iptable_nat ath5k ath pppox ppp_generic nf_nat_ipv4 nf_conntrack_ipv6 nf_conntrack_ipv4 mac80211 ipt_REJECT ipt_MASQUERADE cfg80211 xt_time xt_tcpudp xt_state xt_nat xt_multiport xt_mark xt_mac xt_limit xt_id xt_conntrack xt_comment xt_TCPMSS xt_REDIRECT xt_LOG xt_CT slhc nf_reject_ipv4 nf_nat_redirect nf_nat_masquerade_ipv4 nf_nat nf_log_ipv4 nf_defrag_ipv6 nf_defrag_ipv4 nf_conntrack_rtcache nf_conntrack iptable_raw iptable_mangle iptable_filter ip_tables crc_ccitt compat ip6t_REJECT nf_reject_ipv6 nf_log_ipv6 nf_log_common ip6table_raw ip6table_mangle ip6table_filter ip6_tables x_tables leds_gpio ehci_platform ehci_hcd gpio_button_hotplug usbcore nls_base usb_common ssb_hcd
[ 1318.115124] Process ksoftirqd/0 (pid: 3, threadinfo=8182a000, task=8181e008, tls=00000000)
[ 1318.123424] Stack : 00000000 80c60c94 00db35c0 626a006e ff330000 81acb0e0 81acb0e0 80335b3c
          80c28260 801d818c 80360000 8004f368 00000018 0000000a 803623e0 801e63d8
          8182be10 8182be10 80361100 00000002 803b5dd0 00000001 803b5dd4 00000013
          803b0000 80024fec 80364510 80361100 80360000 8000736c 80364510 8181e008
          80362898 04208040 00018da4 80360000 80310000 803b5dcc 803615a0 803114f4
          ...
[ 1318.160295] Call Trace:
[ 1318.162885] [<80078474>] put_page+0x0/0x4c
[ 1318.167108] [<801d8100>] skb_release_data+0xa8/0x10c
[ 1318.172182] [<801d818c>] __kfree_skb+0x28/0xb4
[ 1318.176752] [<801e63d8>] net_tx_action+0xd8/0x140
[ 1318.181614] [<80024fec>] __do_softirq+0x184/0x2b0
[ 1318.186471] [<80025140>] run_ksoftirqd+0x28/0x80
[ 1318.191238] [<8003bae0>] smpboot_thread_fn+0x148/0x178
[ 1318.196530] [<80039390>] kthread+0xdc/0xe8
[ 1318.200744] [<800010a8>] ret_from_kernel_thread+0x14/0x1c
[ 1318.206200] 
[ 1318.207747] 
Code: 00003021  0801e0ce  24a57888 <8c820000> 3042c000  10400003  00801821  0801df95  00000000 
[ 1318.218397] ---[ end trace 2502a626803fb4b9 ]---
[ 1318.231740] Kernel panic - not syncing: Fatal exception in interrupt
[ 1318.243362] Rebooting in 3 seconds..

This looks similar to: https://dev.openwrt.org/ticket/11091

24.08.2016115Base systemBug ReportVery LowMediumWWAN-connections using 3g with HUAWEI ME909u-521 unstab...TrunkUnconfirmed Task Description

Actually, I am trying to stabilize wwan (3g actually; LTE later on) using pppd with my HUAWEI ME909u-521,
because either my MT7620-based router locks up during boot already; or after short period of real usage.
During night, when router is almost idle, just some watchdog date sent via wwan, no problem.

First trace of a possible problem was this msg in logread:
daemon.notice netifd: wwan (1676): Error setting WWAN mode!

Wich is expected, as in /lib/netifd/proto/3g.sh:

...

                      elif echo "$cardinfo" | grep -qi huawei; then
                              case "$service" in
                                      umts_only) CODE="14,2";;
                                      gprs_only) CODE="13,1";;
                                      *) CODE="2,2";;
                              esac
                              export MODE="AT^SYSCFG=${CODE},3FFFFFFF,2,4"    #####Will not work !!!!! Switching USB-Stick to 3g-preferred ?

...
...

                      [ -n "$MODE" ] && gcom -d "$device" -s /etc/gcom/setmode.gcom

Will not work, because the ME909u-521 rejects AT^SYSCFG . However, AT^SYSCFGEX will work, but having different syntax.
MODE=”AT^SYSCFG=${CODE},3FFFFFFF,2,4” will be effective for simpler modems.

/etc/gcom/setmode.gcom returns exit 1; but this error is not checked in 3g.sh

Not shure, whether this is the reason for my problems; however, reason of concern, as high speed modems
are more and more common.
Willing to participate in testing/debugging.

For details regarding my modem, consult
HUAWEI ME909u-521 LTE LGA Module AT Command Interface Specification
http://www.paoli.cz/out/media/HUAWEI_ME909u-521_LTE_LGA_Module_AT_Command_Interface_Specification-V100R001_02.pdf

16.08.201694Base systemBug ReportVery LowMediumnetifd: PPPoE MTU problemTrunkNew Task Description

When you set the MTU of a ppp interface with proto=pppoe and ifname=nas0 via the mtu option,
the configured mtu will not be set on the ppp interface (what you want), but on the
underlying interface named by ifname (what you normally don’t want to change).

This leeds to log messages like this:


pppd[5641]: Interface nas0 has MTU of 1448 – should be at least 1500.


and MTUs other than what you really want.

example:


desired PPPoE MTU: 1448
actual nas0 MTU: 1448
actual PPPoE MTU: 1440

This issue seems to be related to the commit 7ac29b75319fd69a8a7c0aeea7804d381ec07d3d of netifd.

Regards,
Martin

22.06.201626FlysprayFeature RequestVery LowLowComment formatting syntax should be documentedTrunkResearching Task Description

Currently the formatting options are not documented anywhere, and I failed to find any documentation with google. There are a few buttons to use, but they seem to be rather limited (e.g. nothing for quotations).

Showing tasks 1151 - 1161 of 1161 Page 24 of 24<<First - 20 - 21 - 22 - 23 - 24

Available keyboard shortcuts

Tasklist

Task Details

Task Editing