OpenWrt/LEDE Project

Welcome to the OpenWrt Project bug reporting and issue tracking system

Problems to be reported here are for the current OpenWrt and legacy LEDE Project’s targets, sources, toolchain, core packages, build procedures, distribution and infrastructure. Guidelines for submitting a good bug report can be found at the OpenWrt Project website. Problems related to LuCI or OpenWrt packages need to be reported in their repositories:

Notifications of all submissions and task changes are sent to openwrt-bugs@infradead.org.

OpenedIDCategoryTask TypePriority  descSeveritySummaryReported InStatus
22.08.20213988Base systemBug ReportVery LowLowurlader partition no longer available on Fritzbox 7362 ...TrunkUnconfirmed Task Description

The urlader partition is no longer accessible with current master on a Fritzbox 7362 SL.

As a result, the wireless caldata cannot be loaded. The file /lib/firmware/ath9k-eeprom-pci-0000:01:00.0.bin is created but has a size of 0.

Relevant extract from dmesg:

[    0.569154] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xf1
[    0.574382] nand: Micron MT29F1G08ABADAWP
[    0.578061] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    0.585742] Scanning device for bad blocks
[    0.658779] 2 fixed-partitions partitions found on MTD device 14000000.flash
[    0.664433] Creating 2 MTD partitions on "14000000.flash":
[    0.669871] 0x000000000000-0x000000400000 : "kernel"
[    0.677067] 0x000000400000-0x000008000000 : "ubi"
...
[    0.706366] spi-nor spi0.4: s25fl008k (1024 Kbytes)
[    0.709836] 2 fixed-partitions partitions found on MTD device spi0.4
[    0.716236] Creating 2 MTD partitions on "spi0.4":
[    0.721045] 0x000000040000-0x0000000a0000 : "tffs (1)"
[    0.727521] 0x0000000a0000-0x000000100000 : "tffs (2)"
...
[   22.941707] ath9k 0000:01:00.0: enabling device (0000 -> 0002)
[   22.948389] ath9k 0000:01:00.0: Direct firmware load for ath9k-eeprom-pci-0000:01:00.0.bin failed with error -2
[   22.957623] ath9k 0000:01:00.0: Falling back to sysfs fallback for: ath9k-eeprom-pci-0000:01:00.0.bin
[   23.307603] ath: phy0: Unable to load EEPROM file ath9k-eeprom-pci-0000:01:00.0.bin
[   23.314006] ath9k 0000:01:00.0: Failed to initialize device
[   23.319532] ath9k: probe of 0000:01:00.0 failed with error -22

Maybe this is a side effect of the recent switch to nvmem-cells for reading the MAC address (as this uses the urlader partition)?

22.08.20213987Base systemBug ReportVery LowLowAutonegotiation stopped workingTrunkUnconfirmed Task Description

Supply the following if possible:
- Device problem occurs on ASUS RT-AC65P
- Software versions of OpenWrt 21.02.0-rc3
- Plug WAN port with two-pair cable of an ISP (100Mb/s)
Execute cmd:

ethtool wan

Speed: 1000Mb/s
Duplex: Full
The connection is not working due to the incorrect speed.

Connect the same cable to a switch, and then the router to the same switch. Or execute the command:

ethtool -s wan speed 100 autoneg off duplex full


After that the connection is properly established with proper speed:

ethtool wan

Speed: 100Mb/s
Duplex: Full

Autonegotiation was working properly about a year and a half ago, so there was some changes made in the code that affected it. It also working with no issue with stock firmware.

22.08.20213986Base systemBug ReportVery LowLowAutonegotiation stopped workingTrunkUnconfirmed Task Description

Supply the following if possible:
- Device problem occurs on ASUS RT-AC65P
- Software versions of OpenWrt 21.02.0-rc3
- Plug WAN port with two-pair cable of an ISP (100Mb/s)
Execute cmd:

ethtool wan

Speed: 1000Mb/s
Duplex: Full
The connection is not working due to the incorrect speed.

Connect the same cable to a switch, and then the router to the same switch. Or execute the command:

ethtool -s wan speed 100 autoneg off duplex full


After that the connection is properly established with proper speed:

ethtool wan

Speed: 100Mb/s
Duplex: Full

Autonegotiation was working properly about a year and a half ago, so there was some changes made in the code that affected it. It also working with no issue with stock firmware.

22.08.20213985Base systemBug ReportVery LowLowAutonegotiation stopped workingTrunkUnconfirmed Task Description

Supply the following if possible:
- Device problem occurs on ASUS RT-AC65P
- Software versions of OpenWrt 21.02.0-rc3
- Plug WAN port with two-pair cable of an ISP (100Mb/s)
Execute cmd:
ethtool wan
Settings for wan:
Supported ports: [ TP MII ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Advertised pause frame use: Symmetric Receive-only
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Link partner advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Link partner advertised pause frame use: No
Link partner advertised auto-negotiation: Yes
Link partner advertised FEC modes: Not reported
Speed: 1000Mb/s
Duplex: Full
Port: MII
PHYAD: 0
Transceiver: external
Auto-negotiation: on
Supports Wake-on: d
Wake-on: d
Link detected: yes
The connection is not working due to the incorrect speed.

Connect the same cable to a switch, and then the router to the same switch. Or execute the command:
ethtool -s wan speed 100 autoneg off duplex full
After that the connection is properly established with proper speed:
ethtool wan
Supported ports: [ TP MII ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Advertised pause frame use: Symmetric Receive-only
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Link partner advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
Link partner advertised pause frame use: Symmetric Receive-only
Link partner advertised auto-negotiation: Yes
Link partner advertised FEC modes: Not reported
Speed: 100Mb/s
Duplex: Full
Port: MII
PHYAD: 0
Transceiver: external
Auto-negotiation: on
Supports Wake-on: d
Wake-on: d
Link detected: yes

Autonegotiation was working properly about a year and a half ago, so there was some changes made in the code that affected it. It also working with no issue with stock firmware.

22.08.20213984Base systemBug ReportVery LowLowAutonegotiation stopped workingopenwrt-21.02Unconfirmed Task Description

Supply the following if possible:
- Device problem occurs on ASUS RT-AC65P
- Software versions of OpenWrt 21.02.0-rc3
- Plug WAN port with two-pair cable of an ISP (100Mb/s)
Execute cmd:

ethtool wan

Settings for wan:

      Supported ports: [ TP MII ]
      Supported link modes:   10baseT/Half 10baseT/Full
                              100baseT/Half 100baseT/Full
                              1000baseT/Full
      Supported pause frame use: Symmetric Receive-only
      Supports auto-negotiation: Yes
      Supported FEC modes: Not reported
      Advertised link modes:  10baseT/Half 10baseT/Full
                              100baseT/Half 100baseT/Full
                              1000baseT/Full
      Advertised pause frame use: Symmetric Receive-only
      Advertised auto-negotiation: Yes
      Advertised FEC modes: Not reported
      Link partner advertised link modes:  10baseT/Half 10baseT/Full
                                           100baseT/Half 100baseT/Full
                                           1000baseT/Full
      Link partner advertised pause frame use: No
      Link partner advertised auto-negotiation: Yes
      Link partner advertised FEC modes: Not reported
      Speed: 1000Mb/s
      Duplex: Full
      Port: MII
      PHYAD: 0
      Transceiver: external
      Auto-negotiation: on
      Supports Wake-on: d
      Wake-on: d
      Link detected: yes

The connection is not working due to the incorrect speed.

Connect the same cable to a switch, and then the router to the same switch. Or execute the command:

ethtool -s wan speed 100 autoneg off duplex full

After that the connection is properly established with proper speed:

ethtool wan
      Supported ports: [ TP MII ]
      Supported link modes:   10baseT/Half 10baseT/Full
                              100baseT/Half 100baseT/Full
                              1000baseT/Full
      Supported pause frame use: Symmetric Receive-only
      Supports auto-negotiation: Yes
      Supported FEC modes: Not reported
      Advertised link modes:  10baseT/Half 10baseT/Full
                              100baseT/Half 100baseT/Full
                              1000baseT/Full
      Advertised pause frame use: Symmetric Receive-only
      Advertised auto-negotiation: Yes
      Advertised FEC modes: Not reported
      Link partner advertised link modes:  10baseT/Half 10baseT/Full
                                           100baseT/Half 100baseT/Full
      Link partner advertised pause frame use: Symmetric Receive-only
      Link partner advertised auto-negotiation: Yes
      Link partner advertised FEC modes: Not reported
      Speed: 100Mb/s
      Duplex: Full
      Port: MII
      PHYAD: 0
      Transceiver: external
      Auto-negotiation: on
      Supports Wake-on: d
      Wake-on: d
      Link detected: yes

Autonegotiation was working properly about a year and a half ago, so there was some changes made in the code that affected it. It also working with no issue with stock firmware.

20.08.20213983Base systemBug ReportVery LowLowTX Power 2.4GHZ StuckTrunkUnconfirmed Task Description

I’m having a problem with TXPower with my MediaTek 2.4GHz radio on my R6220 Netgear unit flashed with the latest version of OpenWRT, changing the TX power down to 1 dBm all the way down from 20 has no effect on range or RX power seen by devices. The 5GHz radio does not have this problem, and changing the Tx power has a significant effect on both real world range and signal in dBm. I have tried downgrading software with no luck. Any ideas?

- On both 18.06 and 19.07, tried rolling back.
- Tried reflashing to new OS with no luck
- Netgear R6220
- 2.4GHz Radio with TX Power Issues: MediaTek MT7603E 802.11bgn
- 5GHz Radio That Works Fine: MediaTek MT76x2E 802.11acn

Let me know if I can provide more info.

- Aidan

18.08.20213982PackagesBug ReportVery LowMediumNeed rename "fallthrough" in libubox/utils.h to somethi...TrunkUnconfirmed Task Description

This define: https://lxr.openwrt.org/source/libubox/utils.h#L236 Conflicts with package “nlohmannjson”

Example:

In file included from Json.h:2,
                 from Ubus.h:11,
                 from ModemService.h:6,
                 from ModemService.cpp:1:
/openwrt/staging_dir/target-mipsel_24kc_musl/usr/include/nlohmann/json.hpp:1689:42: error: missing ')' after "__has_attribute"
     JSON_HEDLEY_HAS_ATTRIBUTE(fallthrough) || \
                                          ^
/openwrt/staging_dir/target-mipsel_24kc_musl/usr/include/nlohmann/json.hpp:1689:31: error: missing binary operator before token "("
     JSON_HEDLEY_HAS_ATTRIBUTE(fallthrough) || \
                               ^~~~~~~~~~~
/openwrt/staging_dir/target-mipsel_24kc_musl/usr/include/nlohmann/json.hpp:1692:57: error: missing ')' after "__has_attribute"
 #elif JSON_HEDLEY_HAS_CPP_ATTRIBUTE_NS(clang,fallthrough)
                                                         ^
/openwrt/staging_dir/target-mipsel_24kc_musl/usr/include/nlohmann/json.hpp:1692:46: error: missing binary operator before token "("
 #elif JSON_HEDLEY_HAS_CPP_ATTRIBUTE_NS(clang,fallthrough)
                                              ^~~~~~~~~~~
/openwrt/staging_dir/target-mipsel_24kc_musl/usr/include/nlohmann/json.hpp:1694:48: error: missing ')' after "__has_attribute"
 #elif JSON_HEDLEY_HAS_CPP_ATTRIBUTE(fallthrough)
                                                ^
/openwrt/staging_dir/target-mipsel_24kc_musl/usr/include/nlohmann/json.hpp:1694:37: error: missing binary operator before token "("
 #elif JSON_HEDLEY_HAS_CPP_ATTRIBUTE(fallthrough)
17.08.20213981KernelBug ReportVery LowMediumError using POSIX mqueue on Arduino Yun Rev 2 LEDEyun 1...AllUnconfirmed Task Description

Supply the following if possible:
- Device problem occurs on: Arduino Yun Rev 2 (Atheros ar9331, mips architecture)

- Software versions of OpenWrt/LEDE release, packages, etc.: Used this buildroot to cross-compile for LEDEYun 17.11 https://github.com/arduino/lede-yun

- Steps to reproduce: Able to successfully compile c code that uses POSIX mqueue with above buildroot and toolchain, however after copying the executable over to the Yun I get thrown an error:

 "main:33: (mqd_t)-1 != mq: Function not implemented"

Example code that uses POSIX mqueue and throws the error when running on the yun:

#include <stdlib.h>
#include <stdio.h>
#include <string.h>
#include <sys/stat.h>
#include <sys/types.h>
#include <errno.h>
#include <mqueue.h>
#include <stdio.h> 
#include <string.h> 
#include <stdlib.h>

#include <fcntl.h>

#include "common.h"

int main(int argc, char **argv)
{
    mqd_t mq;
    struct mq_attr attr;
    char buffer[MAX_SIZE + 1];
    int must_stop = 0;

    /* initialize the queue attributes */
    attr.mq_flags = 0;
    attr.mq_maxmsg = 10;
    attr.mq_msgsize = MAX_SIZE;
    attr.mq_curmsgs = 0;

    /* create the message queue */
    mq = mq_open(QUEUE_NAME, O_CREAT | O_RDONLY, 0644, &attr);
    CHECK((mqd_t)-1 != mq);

    do {
        ssize_t bytes_read;

        /* receive the message */
        bytes_read = mq_receive(mq, buffer, MAX_SIZE, NULL);
        CHECK(bytes_read >= 0);

        buffer[bytes_read] = '\0';
        if (! strncmp(buffer, MSG_STOP, strlen(MSG_STOP)))
        {
            must_stop = 1;
        }
        else
        {
            printf("Received: %s\n", buffer);
        }
    } while (!must_stop);

    /* cleanup */
    CHECK((mqd_t)-1 != mq_close(mq));
    CHECK((mqd_t)-1 != mq_unlink(QUEUE_NAME));

    return 0;
}


14.08.20213979KernelBug ReportVery LowLowCONFIG_STAGING is not set on oxnas targetTrunkUnconfirmed Task Description

Supply the following if possible:

- Device problem occurs on
CloudEngines Pogoplug Pro (oxnas target)

- Software versions of OpenWrt/LEDE release, packages, etc.
trunk

- Steps to reproduce
config files for oxnas target contain lines as below.

# CONFIG_STAGING is not set

So, you can’t complie staging drivers such as kmod-fs-exfat package.
Removing those lines works well.
Please see attached patch.

13.08.20213978Base systemBug ReportVery LowLowEA9500 target can not be compiled: os-image partition t...TrunkUnconfirmed Task Description

Supply the following if possible:
- Device problem occurs on

Linksys EA9500 V1

- Software versions of OpenWrt/LEDE release, packages, etc.

Openwrt master snapshot release

- Steps to reproduce

Compile with the default configuration and the following packages:

base-files brcmfmac-firmware-4366c0-pcie busybox ca-bundle dnsmasq dropbear firewall fstools ip6tables iptables iwinfo kmod-brcmfmac kmod-gpio-button-hotplug kmod-ipt-offload kmod-leds-gpio kmod-phy-bcm-ns-usb2 kmod-phy-bcm-ns-usb3 kmod-usb-ledtrig-usbport kmod-usb-ohci kmod-usb2 kmod-usb3 libgcc libustream-wolfssl logd luci mtd netifd nvram odhcp6c odhcpd-ipv6only opkg osafeloader oseama otrx ppp ppp-mod-pppoe procd swconfig uci uclient-fetch urandom-seed urngd wpad-basic-wolfssl

Logs:

STDOUT log:

Checking ‘working-make’... ok.
Checking ‘case-sensitive-fs’... ok.
Checking ‘proper-umask’... ok.
Checking ‘perl-data-dumper’... ok.
Checking ‘perl-findbin’... ok.
Checking ‘perl-file-copy’... ok.
Checking ‘perl-file-compare’... ok.
Checking ‘perl-thread-queue’... ok.
Checking ‘tar’... ok.
Checking ‘find’... ok.
Checking ‘bash’... ok.
Checking ‘xargs’... ok.
Checking ‘patch’... ok.
Checking ‘diff’... ok.
Checking ‘cp’... ok.
Checking ‘seq’... ok.
Checking ‘awk’... ok.
Checking ‘grep’... ok.
Checking ‘egrep’... ok.
Checking ‘getopt’... ok.
Checking ‘stat’... ok.
Checking ‘unzip’... ok.
Checking ‘bzip2’... ok.
Checking ‘wget’... ok.
Checking ‘install’... ok.
Checking ‘perl’... ok.
Checking ‘python2-cleanup’... ok.
Checking ‘python’... ok.
Checking ‘python3’... ok.
Checking ‘git’... ok.
Checking ‘file’... ok.
Checking ‘rsync’... ok.
Checking ‘which’... ok.
Checking ‘ldconfig-stub’... ok.
Building images for bcm53xx - Linksys EA9500
Packages: kmod-usb2 busybox ppp kmod-phy-bcm-ns-usb2 logd procd opkg kmod-usb3 wpad-basic-wolfssl odhcp6c fstools kmod-usb-ledtrig-usbport urandom-seed mtd uclient-fetch iptables osafeloader urngd kmod-brcmfmac base-files firewall swconfig luci brcmfmac-firmware-4366c0-pcie odhcpd-ipv6only ppp-mod-pppoe ca-bundle iwinfo kmod-leds-gpio nvram netifd dropbear uci oseama libustream-wolfssl kmod-usb-ohci otrx dnsmasq kmod-phy-bcm-ns-usb3 kmod-ipt-offload ip6tables kmod-gpio-button-hotplug base-files brcmfmac-firmware-4366c0-pcie busybox ca-bundle dnsmasq dropbear firewall fstools ip6tables iptables iwinfo kernel kmod-brcmfmac kmod-gpio-button-hotplug kmod-ipt-offload kmod-leds-gpio kmod-phy-bcm-ns-usb2 kmod-phy-bcm-ns-usb3 kmod-usb-ledtrig-usbport kmod-usb-ohci kmod-usb2 kmod-usb3 libustream-wolfssl logd mtd netifd nvram odhcp6c odhcpd-ipv6only opkg osafeloader oseama otrx ppp ppp-mod-pppoe procd swconfig uci uclient-fetch urandom-seed urngd wpad-basic-wolfssl

Installing packages...
Installing libc (1.1.24-3) to root...
Installing libgcc1 (8.4.0-3) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/libgcc1_8.4.0-3_arm_cortex-a9.ipk.
Configuring libgcc1.
Configuring libc.
Installing kernel (5.4.138-1-15706bb9be34cef2234d05e29f0e657b) to root...
Configuring kernel.
Installing kmod-usb2 (5.4.138-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/kmod-usb2_5.4.138-1_arm_cortex-a9.ipk.
Installing kmod-nls-base (5.4.138-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/kmod-nls-base_5.4.138-1_arm_cortex-a9.ipk.
Installing kmod-usb-core (5.4.138-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/kmod-usb-core_5.4.138-1_arm_cortex-a9.ipk.
Installing kmod-usb-bcma (5.4.138-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/kmod-usb-bcma_5.4.138-1_arm_cortex-a9.ipk.
Installing kmod-phy-bcm-ns-usb2 (5.4.138-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/kmod-phy-bcm-ns-usb2_5.4.138-1_arm_cortex-a9.ipk.
Installing kmod-usb-ehci (5.4.138-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/kmod-usb-ehci_5.4.138-1_arm_cortex-a9.ipk.
Installing busybox (1.33.1-11) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/busybox_1.33.1-11_arm_cortex-a9.ipk.
Installing ppp (2.4.9.git-2021-01-04-3) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/ppp_2.4.9.git-2021-01-04-3_arm_cortex-a9.ipk.
Installing kmod-lib-crc-ccitt (5.4.138-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/kmod-lib-crc-ccitt_5.4.138-1_arm_cortex-a9.ipk.
Installing kmod-slhc (5.4.138-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/kmod-slhc_5.4.138-1_arm_cortex-a9.ipk.
Installing kmod-ppp (5.4.138-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/kmod-ppp_5.4.138-1_arm_cortex-a9.ipk.
Package kmod-phy-bcm-ns-usb2 (5.4.138-1) installed in root is up to date.
Installing logd (2021-08-03-205defb5-2) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/logd_2021-08-03-205defb5-2_arm_cortex-a9.ipk.
Installing libubox20210516 (2021-05-16-b14c4688-2) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/libubox20210516_2021-05-16-b14c4688-2_arm_cortex-a9.ipk.
Installing libubus20210630 (2021-06-30-4fc532c8-2) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/libubus20210630_2021-06-30-4fc532c8-2_arm_cortex-a9.ipk.
Installing libjson-c5 (0.15-2) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/libjson-c5_0.15-2_arm_cortex-a9.ipk.
Installing libblobmsg-json20210516 (2021-05-16-b14c4688-2) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/libblobmsg-json20210516_2021-05-16-b14c4688-2_arm_cortex-a9.ipk.
Installing procd (2021-08-05-f5d9b14f-2) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/procd_2021-08-05-f5d9b14f-2_arm_cortex-a9.ipk.
Installing ubusd (2021-06-30-4fc532c8-2) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/ubusd_2021-06-30-4fc532c8-2_arm_cortex-a9.ipk.
Installing ubus (2021-06-30-4fc532c8-2) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/ubus_2021-06-30-4fc532c8-2_arm_cortex-a9.ipk.
Installing libjson-script20210516 (2021-05-16-b14c4688-2) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/libjson-script20210516_2021-05-16-b14c4688-2_arm_cortex-a9.ipk.
Installing libuci20130104 (2021-04-14-4b3db117-6) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/libuci20130104_2021-04-14-4b3db117-6_arm_cortex-a9.ipk.
Installing ubox (2021-08-03-205defb5-2) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/ubox_2021-08-03-205defb5-2_arm_cortex-a9.ipk.
Installing jshn (2021-05-16-b14c4688-2) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/jshn_2021-05-16-b14c4688-2_arm_cortex-a9.ipk.
Installing opkg (2021-06-13-1bf042dd-3) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/opkg_2021-06-13-1bf042dd-3_arm_cortex-a9.ipk.
Installing libuclient20201210 (2021-05-14-6a6011df-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/libuclient20201210_2021-05-14-6a6011df-1_arm_cortex-a9.ipk.
Installing uclient-fetch (2021-05-14-6a6011df-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/uclient-fetch_2021-05-14-6a6011df-1_arm_cortex-a9.ipk.
Installing libpthread (1.1.24-3) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/libpthread_1.1.24-3_arm_cortex-a9.ipk.
Installing kmod-usb3 (5.4.138-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/kmod-usb3_5.4.138-1_arm_cortex-a9.ipk.
Installing kmod-usb-xhci-hcd (5.4.138-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/kmod-usb-xhci-hcd_5.4.138-1_arm_cortex-a9.ipk.
Installing kmod-phy-bcm-ns-usb3 (5.4.138-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/kmod-phy-bcm-ns-usb3_5.4.138-1_arm_cortex-a9.ipk.
Installing wpad-basic-wolfssl (2021-05-22-b102f19b-31) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/wpad-basic-wolfssl_2021-05-22-b102f19b-31_arm_cortex-a9.ipk.
Installing libnl-tiny1 (2020-08-05-c291088f-2) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/libnl-tiny1_2020-08-05-c291088f-2_arm_cortex-a9.ipk.
Installing hostapd-common (2021-05-22-b102f19b-31) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/hostapd-common_2021-05-22-b102f19b-31_arm_cortex-a9.ipk.
Installing libwolfssl4.7.0.ba20a816 (4.7.0-stable-2) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/libwolfssl4.7.0.ba20a816_4.7.0-stable-2_arm_cortex-a9.ipk.
Installing odhcp6c (2021-07-14-94adc8bb-18) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/odhcp6c_2021-07-14-94adc8bb-18_arm_cortex-a9.ipk.
Installing fstools (2021-08-05-d4f01298-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/fstools_2021-08-05-d4f01298-1_arm_cortex-a9.ipk.
Installing ubi-utils (2.1.2-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/ubi-utils_2.1.2-1_arm_cortex-a9.ipk.
Installing kmod-usb-ledtrig-usbport (5.4.138-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/kmod-usb-ledtrig-usbport_5.4.138-1_arm_cortex-a9.ipk.
Installing urandom-seed (3) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/urandom-seed_3_arm_cortex-a9.ipk.
Installing getrandom (2021-08-03-205defb5-2) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/getrandom_2021-08-03-205defb5-2_arm_cortex-a9.ipk.
Installing mtd (26) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/mtd_26_arm_cortex-a9.ipk.
Package uclient-fetch (2021-05-14-6a6011df-1) installed in root is up to date.
Installing iptables (1.8.7-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/iptables_1.8.7-1_arm_cortex-a9.ipk.
Installing kmod-nf-reject (5.4.138-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/kmod-nf-reject_5.4.138-1_arm_cortex-a9.ipk.
Installing kmod-nf-ipt (5.4.138-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/kmod-nf-ipt_5.4.138-1_arm_cortex-a9.ipk.
Installing kmod-ipt-core (5.4.138-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/kmod-ipt-core_5.4.138-1_arm_cortex-a9.ipk.
Installing libxtables12 (1.8.7-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/libxtables12_1.8.7-1_arm_cortex-a9.ipk.
Installing libip4tc2 (1.8.7-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/libip4tc2_1.8.7-1_arm_cortex-a9.ipk.
Installing libip6tc2 (1.8.7-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/libip6tc2_1.8.7-1_arm_cortex-a9.ipk.
Installing osafeloader (1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/osafeloader_1_arm_cortex-a9.ipk.
Installing urngd (2020-01-21-c7f7b6b6-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/urngd_2020-01-21-c7f7b6b6-1_arm_cortex-a9.ipk.
Installing kmod-brcmfmac (5.4.138+5.10.42-1-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/kmod-brcmfmac_5.4.138+5.10.42-1-1_arm_cortex-a9.ipk.
Installing iw (5.9-8fab0c9e-3) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/iw_5.9-8fab0c9e-3_arm_cortex-a9.ipk.
Installing libiwinfo-data (2021-07-11-a0a0e02d-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/libiwinfo-data_2021-07-11-a0a0e02d-1_arm_cortex-a9.ipk.
Installing libiwinfo20210430 (2021-07-11-a0a0e02d-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/libiwinfo20210430_2021-07-11-a0a0e02d-1_arm_cortex-a9.ipk.
Installing iwinfo (2021-07-11-a0a0e02d-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/iwinfo_2021-07-11-a0a0e02d-1_arm_cortex-a9.ipk.
Installing wireless-regdb (2021.04.21-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/wireless-regdb_2021.04.21-1_all.ipk.
Installing kmod-cfg80211 (5.4.138+5.10.42-1-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/kmod-cfg80211_5.4.138+5.10.42-1-1_arm_cortex-a9.ipk.
Installing kmod-brcmutil (5.4.138+5.10.42-1-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/kmod-brcmutil_5.4.138+5.10.42-1-1_arm_cortex-a9.ipk.
Installing brcmfmac-firmware-usb (20210511-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/brcmfmac-firmware-usb_20210511-1_arm_cortex-a9.ipk.
Installing base-files (1448-r17328-5181af5585) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/base-files_1448-r17328-5181af5585_arm_cortex-a9.ipk.
Installing netifd (2021-07-26-440eb064-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/netifd_2021-07-26-440eb064-1_arm_cortex-a9.ipk.
Installing jsonfilter (2018-02-04-c7e938d6-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/jsonfilter_2018-02-04-c7e938d6-1_arm_cortex-a9.ipk.
Installing usign (2020-05-23-f1f65026-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/usign_2020-05-23-f1f65026-1_arm_cortex-a9.ipk.
Installing openwrt-keyring (2021-02-20-49283916-2) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/openwrt-keyring_2021-02-20-49283916-2_arm_cortex-a9.ipk.
Installing fwtool (2019-11-12-8f7fe925-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/fwtool_2019-11-12-8f7fe925-1_arm_cortex-a9.ipk.
Installing firewall (2021-03-29-a4355a6f-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/firewall_2021-03-29-a4355a6f-1_arm_cortex-a9.ipk.
Installing kmod-nf-conntrack (5.4.138-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/kmod-nf-conntrack_5.4.138-1_arm_cortex-a9.ipk.
Installing kmod-ipt-conntrack (5.4.138-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/kmod-ipt-conntrack_5.4.138-1_arm_cortex-a9.ipk.
Installing kmod-nf-conntrack6 (5.4.138-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/kmod-nf-conntrack6_5.4.138-1_arm_cortex-a9.ipk.
Installing kmod-nf-nat (5.4.138-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/kmod-nf-nat_5.4.138-1_arm_cortex-a9.ipk.
Installing kmod-ipt-nat (5.4.138-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/kmod-ipt-nat_5.4.138-1_arm_cortex-a9.ipk.
Installing swconfig (12) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/swconfig_12_arm_cortex-a9.ipk.
Installing luci (git-20.074.84698-ead5e81) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/luci_git-20.074.84698-ead5e81_all.ipk.
Installing uhttpd (2021-03-21-15346de8-2) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/uhttpd_2021-03-21-15346de8-2_arm_cortex-a9.ipk.
Installing uhttpd-mod-ubus (2021-03-21-15346de8-2) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/uhttpd-mod-ubus_2021-03-21-15346de8-2_arm_cortex-a9.ipk.
Installing liblua5.1.5 (5.1.5-9) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/liblua5.1.5_5.1.5-9_arm_cortex-a9.ipk.
Installing lua (5.1.5-9) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/lua_5.1.5-9_arm_cortex-a9.ipk.
Installing luci-lib-nixio (git-20.234.06894-c4a4e43) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/luci-lib-nixio_git-20.234.06894-c4a4e43_arm_cortex-a9.ipk.
Installing luci-lib-ip (git-20.250.76529-62505bd) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/luci-lib-ip_git-20.250.76529-62505bd_arm_cortex-a9.ipk.
Installing rpcd (2021-07-13-1fa35765-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/rpcd_2021-07-13-1fa35765-1_arm_cortex-a9.ipk.
Installing libubus-lua (2021-06-30-4fc532c8-2) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/libubus-lua_2021-06-30-4fc532c8-2_arm_cortex-a9.ipk.
Installing luci-lib-jsonc (git-19.317.29469-8da8f38) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/luci-lib-jsonc_git-19.317.29469-8da8f38_arm_cortex-a9.ipk.
Installing liblucihttp0 (2021-06-11-3dc89af4-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/liblucihttp0_2021-06-11-3dc89af4-1_arm_cortex-a9.ipk.
Installing liblucihttp-lua (2021-06-11-3dc89af4-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/liblucihttp-lua_2021-06-11-3dc89af4-1_arm_cortex-a9.ipk.
Installing luci-lib-base (git-20.232.39649-1f6dc29) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/luci-lib-base_git-20.232.39649-1f6dc29_all.ipk.
Installing rpcd-mod-file (2021-07-13-1fa35765-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/rpcd-mod-file_2021-07-13-1fa35765-1_arm_cortex-a9.ipk.
Installing rpcd-mod-luci (20210614) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/rpcd-mod-luci_20210614_arm_cortex-a9.ipk.
Installing cgi-io (2020-10-27-ab4c3471-19) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/cgi-io_2020-10-27-ab4c3471-19_arm_cortex-a9.ipk.
Installing luci-base (git-21.223.61040-6045f58) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/luci-base_git-21.223.61040-6045f58_arm_cortex-a9.ipk.
Installing libiwinfo-lua (2021-07-11-a0a0e02d-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/libiwinfo-lua_2021-07-11-a0a0e02d-1_arm_cortex-a9.ipk.
Installing luci-mod-status (git-21.223.26748-6142579) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/luci-mod-status_git-21.223.26748-6142579_arm_cortex-a9.ipk.
Installing luci-mod-system (git-21.223.26746-8fb2d82) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/luci-mod-system_git-21.223.26746-8fb2d82_all.ipk.
Installing rpcd-mod-iwinfo (2021-07-13-1fa35765-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/rpcd-mod-iwinfo_2021-07-13-1fa35765-1_arm_cortex-a9.ipk.
Installing luci-mod-network (git-21.223.26751-2393289) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/luci-mod-network_git-21.223.26751-2393289_all.ipk.
Installing luci-mod-admin-full (git-19.253.48496-3f93650) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/luci-mod-admin-full_git-19.253.48496-3f93650_all.ipk.
Installing luci-theme-bootstrap (git-21.217.49862-be028dc) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/luci-theme-bootstrap_git-21.217.49862-be028dc_all.ipk.
Installing luci-app-firewall (git-21.223.26742-406e6c8) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/luci-app-firewall_git-21.223.26742-406e6c8_all.ipk.
Installing luci-app-opkg (git-21.079.58548-3bcbcbf) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/luci-app-opkg_git-21.079.58548-3bcbcbf_all.ipk.
Installing luci-proto-ppp (git-21.158.38888-88b9d84) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/luci-proto-ppp_git-21.158.38888-88b9d84_all.ipk.
Installing luci-proto-ipv6 (git-21.148.48881-79947af) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/luci-proto-ipv6_git-21.148.48881-79947af_all.ipk.
Installing rpcd-mod-rrdns (20170710) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/rpcd-mod-rrdns_20170710_arm_cortex-a9.ipk.
Installing brcmfmac-firmware-4366c0-pcie (20210511-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/brcmfmac-firmware-4366c0-pcie_20210511-1_arm_cortex-a9.ipk.
Installing odhcpd-ipv6only (2021-07-18-bc9d317f-3) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/odhcpd-ipv6only_2021-07-18-bc9d317f-3_arm_cortex-a9.ipk.
Installing ppp-mod-pppoe (2.4.9.git-2021-01-04-3) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/ppp-mod-pppoe_2.4.9.git-2021-01-04-3_arm_cortex-a9.ipk.
Installing kmod-pppox (5.4.138-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/kmod-pppox_5.4.138-1_arm_cortex-a9.ipk.
Installing kmod-pppoe (5.4.138-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/kmod-pppoe_5.4.138-1_arm_cortex-a9.ipk.
Installing ca-bundle (20210119-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/ca-bundle_20210119-1_all.ipk.
Package iwinfo (2021-07-11-a0a0e02d-1) installed in root is up to date.
Installing kmod-leds-gpio (5.4.138-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/kmod-leds-gpio_5.4.138-1_arm_cortex-a9.ipk.
Installing nvram (10) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/nvram_10_arm_cortex-a9.ipk.
Package netifd (2021-07-26-440eb064-1) installed in root is up to date.
Installing dropbear (2020.81-2) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/dropbear_2020.81-2_arm_cortex-a9.ipk.
Installing uci (2021-04-14-4b3db117-6) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/uci_2021-04-14-4b3db117-6_arm_cortex-a9.ipk.
Installing oseama (1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/oseama_1_arm_cortex-a9.ipk.
Installing libustream-wolfssl20201210 (2020-12-10-68d09243-2) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/libustream-wolfssl20201210_2020-12-10-68d09243-2_arm_cortex-a9.ipk.
Installing kmod-usb-ohci (5.4.138-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/kmod-usb-ohci_5.4.138-1_arm_cortex-a9.ipk.
Installing otrx (2021-07-30-a5c65fa1-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/otrx_2021-07-30-a5c65fa1-1_arm_cortex-a9.ipk.
Installing dnsmasq (2.85-7) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/dnsmasq_2.85-7_arm_cortex-a9.ipk.
Package kmod-phy-bcm-ns-usb3 (5.4.138-1) installed in root is up to date.
Installing kmod-ipt-offload (5.4.138-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/kmod-ipt-offload_5.4.138-1_arm_cortex-a9.ipk.
Installing kmod-nf-flow (5.4.138-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/kmod-nf-flow_5.4.138-1_arm_cortex-a9.ipk.
Installing ip6tables (1.8.7-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/ip6tables_1.8.7-1_arm_cortex-a9.ipk.
Installing kmod-nf-reject6 (5.4.138-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/kmod-nf-reject6_5.4.138-1_arm_cortex-a9.ipk.
Installing kmod-nf-ipt6 (5.4.138-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/kmod-nf-ipt6_5.4.138-1_arm_cortex-a9.ipk.
Installing kmod-ip6tables (5.4.138-1) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/kmod-ip6tables_5.4.138-1_arm_cortex-a9.ipk.
Installing kmod-gpio-button-hotplug (5.4.138-3) to root...
Copying /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/kmod-gpio-button-hotplug_5.4.138-3_arm_cortex-a9.ipk.
Package base-files (1448-r17328-5181af5585) installed in root is up to date.
Package brcmfmac-firmware-4366c0-pcie (20210511-1) installed in root is up to date.
Package busybox (1.33.1-11) installed in root is up to date.
Package ca-bundle (20210119-1) installed in root is up to date.
Package dnsmasq (2.85-7) installed in root is up to date.
Package dropbear (2020.81-2) installed in root is up to date.
Package firewall (2021-03-29-a4355a6f-1) installed in root is up to date.
Package fstools (2021-08-05-d4f01298-1) installed in root is up to date.
Package ip6tables (1.8.7-1) installed in root is up to date.
Package iptables (1.8.7-1) installed in root is up to date.
Package iwinfo (2021-07-11-a0a0e02d-1) installed in root is up to date.
Package kernel (5.4.138-1-15706bb9be34cef2234d05e29f0e657b) installed in root is up to date.
Package kmod-brcmfmac (5.4.138+5.10.42-1-1) installed in root is up to date.
Package kmod-gpio-button-hotplug (5.4.138-3) installed in root is up to date.
Package kmod-ipt-offload (5.4.138-1) installed in root is up to date.
Package kmod-leds-gpio (5.4.138-1) installed in root is up to date.
Package kmod-phy-bcm-ns-usb2 (5.4.138-1) installed in root is up to date.
Package kmod-phy-bcm-ns-usb3 (5.4.138-1) installed in root is up to date.
Package kmod-usb-ledtrig-usbport (5.4.138-1) installed in root is up to date.
Package kmod-usb-ohci (5.4.138-1) installed in root is up to date.
Package kmod-usb2 (5.4.138-1) installed in root is up to date.
Package kmod-usb3 (5.4.138-1) installed in root is up to date.
Package libustream-wolfssl20201210 (2020-12-10-68d09243-2) installed in root is up to date.
Package logd (2021-08-03-205defb5-2) installed in root is up to date.
Package mtd (26) installed in root is up to date.
Package netifd (2021-07-26-440eb064-1) installed in root is up to date.
Package nvram (10) installed in root is up to date.
Package odhcp6c (2021-07-14-94adc8bb-18) installed in root is up to date.
Package odhcpd-ipv6only (2021-07-18-bc9d317f-3) installed in root is up to date.
Package opkg (2021-06-13-1bf042dd-3) installed in root is up to date.
Package osafeloader (1) installed in root is up to date.
Package oseama (1) installed in root is up to date.
Package otrx (2021-07-30-a5c65fa1-1) installed in root is up to date.
Package ppp (2.4.9.git-2021-01-04-3) installed in root is up to date.
Package ppp-mod-pppoe (2.4.9.git-2021-01-04-3) installed in root is up to date.
Package procd (2021-08-05-f5d9b14f-2) installed in root is up to date.
Package swconfig (12) installed in root is up to date.
Package uci (2021-04-14-4b3db117-6) installed in root is up to date.
Package uclient-fetch (2021-05-14-6a6011df-1) installed in root is up to date.
Package urandom-seed (3) installed in root is up to date.
Package urngd (2020-01-21-c7f7b6b6-1) installed in root is up to date.
Package wpad-basic-wolfssl (2021-05-22-b102f19b-31) installed in root is up to date.
Configuring libnl-tiny1.
Configuring libubox20210516.
Configuring libuci20130104.
Configuring libubus20210630.
Configuring libiwinfo-data.
Configuring libiwinfo20210430.
Configuring iwinfo.
Configuring liblucihttp0.
Configuring cgi-io.
Configuring liblua5.1.5.
Configuring lua.
Configuring luci-lib-nixio.
Configuring luci-lib-ip.
Configuring libjson-c5.
Configuring luci-lib-jsonc.
Configuring liblucihttp-lua.
Configuring luci-lib-base.
Configuring kmod-nls-base.
Configuring kmod-usb-core.
Configuring kmod-usb-bcma.
Configuring libuclient20201210.
Configuring uclient-fetch.
Configuring libpthread.
Configuring opkg.
Configuring luci-app-opkg.
Configuring libblobmsg-json20210516.
Configuring ubusd.
Configuring ubus.
Configuring iw.
Configuring rpcd.
Configuring busybox.
Configuring libubus-lua.
Configuring libwolfssl4.7.0.ba20a816.
Configuring kmod-nf-reject6.
Configuring libiwinfo-lua.
Configuring swconfig.
Configuring rpcd-mod-file.
Configuring rpcd-mod-luci.
Configuring luci-base.
Configuring luci-mod-system.
Configuring kmod-nf-conntrack.
Configuring kmod-nf-flow.
Configuring libustream-wolfssl20201210.
Configuring kmod-lib-crc-ccitt.
Configuring getrandom.
Configuring luci-theme-bootstrap.
Configuring kmod-slhc.
Configuring kmod-ppp.
Configuring kmod-pppox.
Configuring kmod-pppoe.
Configuring kmod-phy-bcm-ns-usb2.
Configuring kmod-phy-bcm-ns-usb3.
Configuring hostapd-common.
Configuring wpad-basic-wolfssl.
Configuring kmod-nf-reject.
Configuring kmod-nf-ipt.
Configuring kmod-ipt-core.
Configuring kmod-ipt-conntrack.
Configuring jshn.
Configuring netifd.
Configuring jsonfilter.
Configuring usign.
Configuring openwrt-keyring.
Configuring ubi-utils.
Configuring ubox.
Configuring fstools.
Configuring fwtool.
Configuring base-files.
Configuring kmod-nf-nat.
Configuring libjson-script20210516.
Configuring kmod-usb-ohci.
Configuring dnsmasq.
Configuring kmod-usb-xhci-hcd.
Configuring procd.
Configuring kmod-usb-ehci.
Configuring luci-mod-status.
Configuring libxtables12.
Configuring kmod-usb2.
Configuring kmod-usb3.
Configuring libip4tc2.
Configuring libip6tc2.
Configuring kmod-nf-conntrack6.
Configuring kmod-ipt-nat.
Configuring firewall.
Configuring luci-app-firewall.
Configuring kmod-nf-ipt6.
Configuring kmod-ip6tables.
Configuring odhcp6c.
Configuring uci.
Configuring dropbear.
Configuring oseama.
Configuring mtd.
Configuring odhcpd-ipv6only.
Configuring wireless-regdb.
Configuring kmod-cfg80211.
Configuring kmod-brcmutil.
Configuring brcmfmac-firmware-usb.
Configuring kmod-brcmfmac.
Configuring urandom-seed.
Configuring nvram.
Configuring luci-proto-ppp.
Configuring otrx.
Configuring ppp.
Configuring rpcd-mod-iwinfo.
Configuring luci-mod-network.
Configuring luci-mod-admin-full.
Configuring kmod-leds-gpio.
Configuring kmod-gpio-button-hotplug.
Configuring logd.
Configuring brcmfmac-firmware-4366c0-pcie.
Configuring luci-proto-ipv6.
Configuring iptables.
Configuring uhttpd.
Configuring ip6tables.
Configuring ca-bundle.
Configuring uhttpd-mod-ubus.
Configuring rpcd-mod-rrdns.
Configuring luci.
Configuring kmod-usb-ledtrig-usbport.
Configuring osafeloader.
Configuring kmod-ipt-offload.
Configuring urngd.
Configuring ppp-mod-pppoe.

Finalizing root filesystem...
Enabling boot
Enabling clear_partialboot
Enabling cron
Enabling dnsmasq
Enabling done
Enabling dropbear
Enabling firewall
Enabling gpio_switch
Enabling led
Enabling log
Enabling network
Enabling odhcpd
Enabling rpcd
Enabling sysctl
Enabling sysfixtime
Enabling sysntpd
Enabling system
Enabling ucitrack
Enabling uhttpd
Enabling umount
Enabling urandom_seed
Enabling urngd
Enabling wpad

Building images...
Parallel mksquashfs: Using 1 processor
Creating 4.0 filesystem on /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/build_dir/target-arm_cortex-a9_musl_eabi/linux-bcm53xx_generic/root.squashfs, block size 262144.

[===============================================================-] 949/949 100%

Exportable Squashfs 4.0 filesystem, xz compressed, data block size 262144

compressed data, compressed metadata, compressed fragments,
no xattrs, compressed ids
duplicates are removed

Filesystem size 3801.76 Kbytes (3.71 Mbytes)

36.11% of uncompressed filesystem size (10527.64 Kbytes)

Inode table size 8468 bytes (8.27 Kbytes)

20.30% of uncompressed inode table size (41706 bytes)

Directory table size 12228 bytes (11.94 Kbytes)

45.77% of uncompressed directory table size (26717 bytes)

Number of duplicate files found 137
Number of inodes 1259
Number of files 945
Number of fragments 27
Number of symbolic links 200
Number of device nodes 1
Number of fifo nodes 0
Number of socket nodes 0
Number of directories 113
Number of ids (unique uids + gids) 1
Number of uids 1

unknown (0)

Number of gids 1

unknown (0)

[rootfs]
mode=ubi
vol_id=0
vol_type=dynamic
vol_name=rootfs
image=/home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/build_dir/target-arm_cortex-a9_musl_eabi/linux-bcm53xx_generic/root.squashfs
vol_size=3893248
[rootfs_data]
mode=ubi
vol_id=1
vol_type=dynamic
vol_name=rootfs_data
vol_size=1MiB
vol_flags=autoresize
[rootfs]
mode=ubi
vol_id=0
vol_type=dynamic
vol_name=rootfs
image=/home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/build_dir/target-arm_cortex-a9_musl_eabi/linux-bcm53xx_generic/root.squashfs
vol_size=3893248
[rootfs_data]
mode=ubi
vol_id=1
vol_type=dynamic
vol_name=rootfs_data
vol_size=1MiB
vol_flags=autoresize
[rootfs]
mode=ubi
vol_id=0
vol_type=dynamic
vol_name=rootfs
image=/home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/build_dir/target-arm_cortex-a9_musl_eabi/linux-bcm53xx_generic/root.squashfs
vol_size=3893248
[rootfs_data]
mode=ubi
vol_id=1
vol_type=dynamic
vol_name=rootfs_data
vol_size=1MiB
vol_flags=autoresize
[rootfs]
mode=ubi
vol_id=0
vol_type=dynamic
vol_name=rootfs
image=/home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/build_dir/target-arm_cortex-a9_musl_eabi/linux-bcm53xx_generic/root.squashfs
vol_size=3893248
[rootfs_data]
mode=ubi
vol_id=1
vol_type=dynamic
vol_name=rootfs_data
vol_size=1MiB
vol_flags=autoresize
[rootfs]
mode=ubi
vol_id=0
vol_type=dynamic
vol_name=rootfs
image=/home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/build_dir/target-arm_cortex-a9_musl_eabi/linux-bcm53xx_generic/root.squashfs
vol_size=3893248
[rootfs_data]
mode=ubi
vol_id=1
vol_type=dynamic
vol_name=rootfs_data
vol_size=1MiB
vol_flags=autoresize
[rootfs]
mode=ubi
vol_id=0
vol_type=dynamic
vol_name=rootfs
image=/home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/build_dir/target-arm_cortex-a9_musl_eabi/linux-bcm53xx_generic/root.squashfs
vol_size=3893248
[rootfs_data]
mode=ubi
vol_id=1
vol_type=dynamic
vol_name=rootfs_data
vol_size=1MiB
vol_flags=autoresize
[rootfs]
mode=ubi
vol_id=0
vol_type=dynamic
vol_name=rootfs
image=/home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/build_dir/target-arm_cortex-a9_musl_eabi/linux-bcm53xx_generic/root.squashfs
vol_size=3893248
[rootfs_data]
mode=ubi
vol_id=1
vol_type=dynamic
vol_name=rootfs_data
vol_size=1MiB
vol_flags=autoresize
[rootfs]
mode=ubi
vol_id=0
vol_type=dynamic
vol_name=rootfs
image=/home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/build_dir/target-arm_cortex-a9_musl_eabi/linux-bcm53xx_generic/root.squashfs
vol_size=3893248
[rootfs_data]
mode=ubi
vol_id=1
vol_type=dynamic
vol_name=rootfs_data
vol_size=1MiB
vol_flags=autoresize
[rootfs]
mode=ubi
vol_id=0
vol_type=dynamic
vol_name=rootfs
image=/home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/build_dir/target-arm_cortex-a9_musl_eabi/linux-bcm53xx_generic/root.squashfs
vol_size=3893248
[rootfs_data]
mode=ubi
vol_id=1
vol_type=dynamic
vol_name=rootfs_data
vol_size=1MiB
vol_flags=autoresize
[rootfs]
mode=ubi
vol_id=0
vol_type=dynamic
vol_name=rootfs
image=/home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/build_dir/target-arm_cortex-a9_musl_eabi/linux-bcm53xx_generic/root.squashfs
vol_size=3893248
[rootfs_data]
mode=ubi
vol_id=1
vol_type=dynamic
vol_name=rootfs_data
vol_size=1MiB
vol_flags=autoresize
[rootfs]
mode=ubi
vol_id=0
vol_type=dynamic
vol_name=rootfs
image=/home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/build_dir/target-arm_cortex-a9_musl_eabi/linux-bcm53xx_generic/root.squashfs
vol_size=3893248
[rootfs_data]
mode=ubi
vol_id=1
vol_type=dynamic
vol_name=rootfs_data
vol_size=1MiB
vol_flags=autoresize
[rootfs]
mode=ubi
vol_id=0
vol_type=dynamic
vol_name=rootfs
image=/home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/build_dir/target-arm_cortex-a9_musl_eabi/linux-bcm53xx_generic/root.squashfs
vol_size=3893248
[rootfs_data]
mode=ubi
vol_id=1
vol_type=dynamic
vol_name=rootfs_data
vol_size=1MiB
vol_flags=autoresize
[rootfs]
mode=ubi
vol_id=0
vol_type=dynamic
vol_name=rootfs
image=/home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/build_dir/target-arm_cortex-a9_musl_eabi/linux-bcm53xx_generic/root.squashfs
vol_size=3893248
[rootfs_data]
mode=ubi
vol_id=1
vol_type=dynamic
vol_name=rootfs_data
vol_size=1MiB
vol_flags=autoresize
[rootfs]
mode=ubi
vol_id=0
vol_type=dynamic
vol_name=rootfs
image=/home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/build_dir/target-arm_cortex-a9_musl_eabi/linux-bcm53xx_generic/root.squashfs
vol_size=3893248
[rootfs_data]
mode=ubi
vol_id=1
vol_type=dynamic
vol_name=rootfs_data
vol_size=1MiB
vol_flags=autoresize
[rootfs]
mode=ubi
vol_id=0
vol_type=dynamic
vol_name=rootfs
image=/home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/build_dir/target-arm_cortex-a9_musl_eabi/linux-bcm53xx_generic/root.squashfs
vol_size=3893248
[rootfs_data]
mode=ubi
vol_id=1
vol_type=dynamic
vol_name=rootfs_data
vol_size=1MiB
vol_flags=autoresize
[rootfs]
mode=ubi
vol_id=0
vol_type=dynamic
vol_name=rootfs
image=/home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/build_dir/target-arm_cortex-a9_musl_eabi/linux-bcm53xx_generic/root.squashfs
vol_size=3893248
[rootfs_data]
mode=ubi
vol_id=1
vol_type=dynamic
vol_name=rootfs_data
vol_size=1MiB
vol_flags=autoresize
[rootfs]
mode=ubi
vol_id=0
vol_type=dynamic
vol_name=rootfs
image=/home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/build_dir/target-arm_cortex-a9_musl_eabi/linux-bcm53xx_generic/root.squashfs
vol_size=3893248
[rootfs_data]
mode=ubi
vol_id=1
vol_type=dynamic
vol_name=rootfs_data
vol_size=1MiB
vol_flags=autoresize
[rootfs]
mode=ubi
vol_id=0
vol_type=dynamic
vol_name=rootfs
image=/home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/build_dir/target-arm_cortex-a9_musl_eabi/linux-bcm53xx_generic/root.squashfs
vol_size=3893248
[rootfs_data]
mode=ubi
vol_id=1
vol_type=dynamic
vol_name=rootfs_data
vol_size=1MiB
vol_flags=autoresize
sysupgrade-meraki_mr32/
sysupgrade-meraki_mr32/CONTROL
sysupgrade-meraki_mr32/kernel
sysupgrade-meraki_mr32/root
[rootfs]
mode=ubi
vol_id=0
vol_type=dynamic
vol_name=rootfs
image=/home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/build_dir/target-arm_cortex-a9_musl_eabi/linux-bcm53xx_generic/root.squashfs
vol_size=3893248
[rootfs_data]
mode=ubi
vol_id=1
vol_type=dynamic
vol_name=rootfs_data
vol_size=1MiB
vol_flags=autoresize
[rootfs]
mode=ubi
vol_id=0
vol_type=dynamic
vol_name=rootfs
image=/home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/build_dir/target-arm_cortex-a9_musl_eabi/linux-bcm53xx_generic/root.squashfs
vol_size=3893248
[rootfs_data]
mode=ubi
vol_id=1
vol_type=dynamic
vol_name=rootfs_data
vol_size=1MiB
vol_flags=autoresize
[rootfs]
mode=ubi
vol_id=0
vol_type=dynamic
vol_name=rootfs
image=/home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/build_dir/target-arm_cortex-a9_musl_eabi/linux-bcm53xx_generic/root.squashfs
vol_size=3893248
[rootfs_data]
mode=ubi
vol_id=1
vol_type=dynamic
vol_name=rootfs_data
vol_size=1MiB
vol_flags=autoresize
[rootfs]
mode=ubi
vol_id=0
vol_type=dynamic
vol_name=rootfs
image=/home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/build_dir/target-arm_cortex-a9_musl_eabi/linux-bcm53xx_generic/root.squashfs
vol_size=3893248
[rootfs_data]
mode=ubi
vol_id=1
vol_type=dynamic
vol_name=rootfs_data
vol_size=1MiB
vol_flags=autoresize
[rootfs]
mode=ubi
vol_id=0
vol_type=dynamic
vol_name=rootfs
image=/home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/build_dir/target-arm_cortex-a9_musl_eabi/linux-bcm53xx_generic/root.squashfs
vol_size=3893248
[rootfs_data]
mode=ubi
vol_id=1
vol_type=dynamic
vol_name=rootfs_data
vol_size=1MiB
vol_flags=autoresize
[rootfs]
mode=ubi
vol_id=0
vol_type=dynamic
vol_name=rootfs
image=/home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/build_dir/target-arm_cortex-a9_musl_eabi/linux-bcm53xx_generic/root.squashfs
vol_size=3893248
[rootfs_data]
mode=ubi
vol_id=1
vol_type=dynamic
vol_name=rootfs_data
vol_size=1MiB
vol_flags=autoresize
[rootfs]
mode=ubi
vol_id=0
vol_type=dynamic
vol_name=rootfs
image=/home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/build_dir/target-arm_cortex-a9_musl_eabi/linux-bcm53xx_generic/root.squashfs
vol_size=3893248
[rootfs_data]
mode=ubi
vol_id=1
vol_type=dynamic
vol_name=rootfs_data
vol_size=1MiB
vol_flags=autoresize

STDERR log:

Downloading http://downloads.cdn.openwrt.org/snapshots/targets/bcm53xx/generic/packages/Packages.gz Updated list of available packages in /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/build_dir/target-arm_cortex-a9_musl_eabi/root-bcm53xx/../../../../../../../../../../home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/openwrt_core
Downloading http://downloads.cdn.openwrt.org/snapshots/targets/bcm53xx/generic/packages/Packages.sig Signature check passed.
Downloading http://downloads.cdn.openwrt.org/snapshots/packages/arm_cortex-a9/base/Packages.gz Updated list of available packages in /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/build_dir/target-arm_cortex-a9_musl_eabi/root-bcm53xx/../../../../../../../../../../home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/openwrt_base
Downloading http://downloads.cdn.openwrt.org/snapshots/packages/arm_cortex-a9/base/Packages.sig Signature check passed.
Downloading http://downloads.cdn.openwrt.org/snapshots/targets/bcm53xx/generic/kmods/5.4.138-1-15706bb9be34cef2234d05e29f0e657b/Packages.gz Updated list of available packages in /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/build_dir/target-arm_cortex-a9_musl_eabi/root-bcm53xx/../../../../../../../../../../home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/openwrt_kmods
Downloading http://downloads.cdn.openwrt.org/snapshots/targets/bcm53xx/generic/kmods/5.4.138-1-15706bb9be34cef2234d05e29f0e657b/Packages.sig Signature check passed.
Downloading http://downloads.cdn.openwrt.org/snapshots/packages/arm_cortex-a9/luci/Packages.gz Updated list of available packages in /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/build_dir/target-arm_cortex-a9_musl_eabi/root-bcm53xx/../../../../../../../../../../home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/openwrt_luci
Downloading http://downloads.cdn.openwrt.org/snapshots/packages/arm_cortex-a9/luci/Packages.sig Signature check passed.
Downloading http://downloads.cdn.openwrt.org/snapshots/packages/arm_cortex-a9/packages/Packages.gz Updated list of available packages in /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/build_dir/target-arm_cortex-a9_musl_eabi/root-bcm53xx/../../../../../../../../../../home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/openwrt_packages
Downloading http://downloads.cdn.openwrt.org/snapshots/packages/arm_cortex-a9/packages/Packages.sig Signature check passed.
Downloading http://downloads.cdn.openwrt.org/snapshots/packages/arm_cortex-a9/routing/Packages.gz Updated list of available packages in /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/build_dir/target-arm_cortex-a9_musl_eabi/root-bcm53xx/../../../../../../../../../../home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/openwrt_routing
Downloading http://downloads.cdn.openwrt.org/snapshots/packages/arm_cortex-a9/routing/Packages.sig Signature check passed.
Downloading http://downloads.cdn.openwrt.org/snapshots/packages/arm_cortex-a9/telephony/Packages.gz Updated list of available packages in /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/build_dir/target-arm_cortex-a9_musl_eabi/root-bcm53xx/../../../../../../../../../../home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/openwrt_telephony
Downloading http://downloads.cdn.openwrt.org/snapshots/packages/arm_cortex-a9/telephony/Packages.sig Signature check passed.
Downloading https://feed.libremesh.org/master/Packages.gz Updated list of available packages in /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/build_dir/target-arm_cortex-a9_musl_eabi/root-bcm53xx/../../../../../../../../../../home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/lime-packages
Downloading https://feed.libremesh.org/master/Packages.sig Signature check passed.
Downloading https://feed.libremesh.org/profiles/Packages.gz Updated list of available packages in /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/build_dir/target-arm_cortex-a9_musl_eabi/root-bcm53xx/../../../../../../../../../../home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/dl/lime-profiles
Downloading https://feed.libremesh.org/profiles/Packages.sig Signature check passed.
Pseudo file “/dev” exists in source filesystem “/home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/build_dir/target-arm_cortex-a9_musl_eabi/root-bcm53xx/dev”.
Ignoring, exclude it (-e/-ef) to override.
7603+1 records in
7603+1 records out
3893006 bytes (3.9 MB, 3.7 MiB) copied, 0.0238177 s, 163 MB/s
3801+1 records in
3802+0 records out
3893248 bytes (3.9 MB, 3.7 MiB) copied, 0.0130074 s, 299 MB/s
mkchkimg: Netgear CHK writer - v0.1
mkchkimg: Board Id: U12H245T00_NETGEAR
mkchkimg: Region: World Wide (WW)
mkchkimg: Kernel Len: 8650752
mkchkimg: Kernel Checksum: 0x954039f5
mkchkimg: Image Checksum: 0x954039f5
mkchkimg: Netgear CHK writer - v0.1
mkchkimg: Board Id: U12H240T00_NETGEAR
mkchkimg: Region: World Wide (WW)
mkchkimg: Kernel Len: 8650752
mkchkimg: Kernel Checksum: 0xa49a1e23
mkchkimg: Image Checksum: 0xa49a1e23
mkchkimg: Netgear CHK writer - v0.1
mkchkimg: Board Id: U12H270T00_NETGEAR
mkchkimg: Region: World Wide (WW)
mkchkimg: Kernel Len: 8650752
mkchkimg: Kernel Checksum: 0x21354dab
mkchkimg: Image Checksum: 0x21354dab
mkchkimg: Netgear CHK writer - v0.1
mkchkimg: Board Id: U12H315T30_NETGEAR
mkchkimg: Region: World Wide (WW)
mkchkimg: Kernel Len: 8650752
mkchkimg: Kernel Checksum: 0x1ce5e9f3
mkchkimg: Image Checksum: 0x1ce5e9f3
mkchkimg: Netgear CHK writer - v0.1
mkchkimg: Board Id: U12H315T00_NETGEAR
mkchkimg: Region: World Wide (WW)
mkchkimg: Kernel Len: 8650752
mkchkimg: Kernel Checksum: 0x1211a4a0
mkchkimg: Image Checksum: 0x1211a4a0
mkchkimg: Netgear CHK writer - v0.1
mkchkimg: Board Id: U12H334T00_NETGEAR
mkchkimg: Region: World Wide (WW)
mkchkimg: Kernel Len: 8650752
mkchkimg: Kernel Checksum: 0xaa234c62
mkchkimg: Image Checksum: 0xaa234c62
7603+1 records in
7603+1 records out
3893006 bytes (3.9 MB, 3.7 MiB) copied, 0.0228145 s, 171 MB/s
7603+1 records in
7603+1 records out
3893006 bytes (3.9 MB, 3.7 MiB) copied, 0.0219404 s, 177 MB/s
7603+1 records in
7603+1 records out
3893006 bytes (3.9 MB, 3.7 MiB) copied, 0.0213838 s, 182 MB/s
mjn3’s trx replacement - v0.81.1
WARNING: maxlen exceeds default maximum! Beware of overwriting nvram!
os-image partition too big (more than 2097152 bytes): Success
make[3]: * [Makefile:456: /home/aparcar/asu/cache/SNAPSHOT/bcm53xx/generic/build_dir/target-arm_cortex-a9_musl_eabi/linux-bcm53xx_generic/tmp/openwrt-66bd9d77e5aa-bcm53xx-generic-tplink_archer-c5-v2-squashfs.bin] Error 1
make[2]:
* [Makefile:186: build_image] Error 2
make[1]: * [Makefile:124: _call_image] Error 2
make:
* [Makefile:240: image] Error 2

 


11.08.20213974Base systemBug ReportVery LowLow CONFIG_KERNEL_KALLSYMS not set for x86 images making b...TrunkUnconfirmed Task Description

Supply the following if possible:
- Device problem occurs on

Virtualbox VM 64 bit

- Software versions of OpenWrt/LEDE release, packages, etc.

19.07.8

- Steps to reproduce

An example of a backtrace sans symbols is attached.

 


10.08.20213972KernelBug ReportVery LowMediumdevolo WiFi pro 1200e: 803x_aneg_done: SGMII link is no...openwrt-19.07Unconfirmed Task Description

My devolo WiFi pro 1200e with uptodate 19.07 has sometimes connectivity issues on the ethernet ports.
Usually the device works just fine (only a Wifi-Repeater and Wifi-to-eth-bridge).
Sometimes it is not possible to use one or both eth ports.

The logread just spams the following line every seconds:

kern.warn kernel: 803x_aneg_done: SGMII link is not ok

Since this was the first message in the log, I dont know if there are previous errors which help find the problem.
Restarting the network does not help, only rebooting over ssh solves the issue.

09.08.20213971Base systemBug ReportVery LowCriticalZyxel nbg-419v2 bootloopopenwrt-21.02Unconfirmed Task Description

after upgrading my zyxel nbg-419v2 to 2021.02RC4 i noticed a bootloop

when connecting the serial cable it turned out to be a kernel unpacking issue:

raspi_read: from:50000 len:40 
.   Image Name:   MIPS OpenWrt Linux-5.4.137
   Created:      2021-07-31  17:21:01 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1496161 Bytes =  1.4 MB
   Load Address: 80000000
   Entry Point:  80000000
raspi_read: from:50040 len:16d461 
.......................   Verifying Checksum ... OK
   Uncompressing Kernel Image ... LZMA ERROR 1 - must RESET board to recover


U-Boot 1.1.3 (Jun  9 2012 - 07:23:11)

Board: Ralink APSoC DRAM:  64 MB
relocate_code Pointer at: 83fac000
******************************
Software System Reset Occurred
******************************
spi_wait_nsec: 3c 
spi device id: c2 20 17 c2 20 (2017c220)
find flash: MX25L6405D

once i managed flashing 19.07.08 via tftp it works again as expected.

unfortunately the wiki was more misleading than helping, especally the magic number is wrong, it seems the right one is already in the normal images, so changing makes things worse.

08.08.20213969Base systemBug ReportVery LowLowLow RSSI on MikroTik RouterBOARD hAP ac² with OpenWRT 2...openwrt-21.02Unconfirmed Task Description

Device : MikroTik RouterBOARD hAP ac² (RBD52G-5HacD2HnD-TC)
Software: OpenWrt 21.02
Steps to reproduce
I have been boot with initramfs image v21.02.0-rc3 (r16172-2aba3e9784). Everything is good except wireless performance. When I connect 5GHz wireless with my Iphone and Macbook Pro, RSSI is too low even at near the rooter. When I walk away the rooter connection is lost. Also When I want to connect 2GHz, connection is lost immediately.

Router Informations
ID: RBD52G-5HacD2HnD-TC
FCC ID: TV7RBD52-5ACD2ND
SN: —/925/r2
MAC address: Starts with 74:4D:28
Type: INTL
Plug: EU

root@OpenWrt:~# cat /etc/config/wireless

config wifi-device 'radio0'
        option type 'mac80211'
        option channel '11'
        option hwmode '11g'
        option path 'platform/soc/a000000.wifi'
        option htmode 'HT20'
        option disabled '1'
        option country 'TR'

config wifi-iface 'default_radio0'
        option device 'radio0'
        option network 'lan'
        option mode 'ap'
        option ssid 'OpenWrt'
        option encryption 'none'

config wifi-device 'radio1'
        option type 'mac80211'
        option channel '36'
        option hwmode '11a'
        option path 'platform/soc/a800000.wifi'
        option htmode 'VHT80'
        option cell_density '0'
        option country 'TR'

config wifi-iface 'default_radio1'
        option device 'radio1'
        option network 'lan'
        option mode 'ap'
        option ssid 'OpenWrt5g'
        option encryption 'psk2'
        option key 'password1234'
root@OpenWrt:~# iwinfo wlan1 assoclist
5E:32:48:9F:08:94  -99 dBm / -112 dBm (SNR 13)  130 ms ago
        RX: 65.0 MBit/s, VHT-MCS 1, 80MHz, VHT-NSS 1      2590 Pkts.
        TX: 351.0 MBit/s, VHT-MCS 4, 80MHz, VHT-NSS 2      3162 Pkts.
        expected throughput: unknown


07.08.20213968Base systemBug ReportVery LowLowIncorrect channel reported by ath10k-*-htt firmwareTrunkUnconfirmed Task Description

Supply the following if possible:
- Device problem occurs on
- Software versions of OpenWrt/LEDE release, packages, etc.
- Steps to reproduce

 

Devices: Archer C7 v2, Linksys EA8300
OpenWRT: 21.02 rc4

Steps:

1. (Archer) Replace default ath10k-firmware-qca988x-ct firmware with ath10k-firmware-qca988x-ct-full-htt

opkg remove ath10k-firmware-qca988x-ct && opkg install ath10k-firmware-qca988x-ct-full-htt && reboot

(EA8300) Replace default ath10k-firmware-qca4019-ct firmware with ath10k-firmware-qca4019-ct-htt

opkg remove ath10k-firmware-qca4019-ct && opkg install ath10k-firmware-qca4019-ct-htt  && reboot

2. Set wireless device to channel 36 and create an ssid
cat /etc/config/wireless:

config wifi-device 'radio2'
	option type 'mac80211'
	option hwmode '11a'
	option path 'platform/soc/a800000.wifi'
	option htmode 'VHT80'
	option cell_density '0'
	option channel '36'

config wifi-iface 'wifinet6'
	option device 'radio2'
	option mode 'ap'
	option ssid 'ssid'
	option encryption 'sae'
	option key 'xxxxxxx'
	option ieee80211w '2'
	option wds '1'
	option network 'lan'

3. iwinfo and luci reports operation on channel 40:
Archer:
wlan0-1 ESSID: “ssid”

        Access Point: XX:XX:XX:XX:XX
        Mode: Client  Channel: 40 (5.200 GHz)
        Center Channel 1: 42 2: unknown
        Tx-Power: 20 dBm  Link Quality: 52/70
        Signal: -58 dBm  Noise: -102 dBm
        Bit Rate: 351.0 MBit/s
        Encryption: WPA3 SAE (CCMP)
        Type: nl80211  HW Mode(s): 802.11nac
        Hardware: 168C:003C 0000:0000 [Qualcomm Atheros QCA9880]
        TX power offset: none
        Frequency offset: none
        Supports VAPs: yes  PHY name: phy0

EA8300:
wlan2 ESSID: “ssid”

        Access Point: XX:XX:XX:XX:XX
        Mode: Master  Channel: 40 (5.200 GHz)
        Center Channel 1: 42 2: unknown
        Tx-Power: 23 dBm  Link Quality: 31/70
        Signal: -79 dBm  Noise: -105 dBm
        Bit Rate: 866.7 MBit/s
        Encryption: WPA3 SAE (CCMP)
        Type: nl80211  HW Mode(s): 802.11nac
        Hardware: 168C:003C 168C:4019 [Qualcomm Atheros IPQ4019]
        TX power offset: none
        Frequency offset: none
        Supports VAPs: yes  PHY name: phy2

My wifi analyzers show that the signal is actually on channel 36, it is just reported incorrectly by the firmware.

06.08.20213967Base systemBug ReportVery LowCriticalsnapshot / gswip 1e108000.switch: dsa switch register f...TrunkUnconfirmed Task Description

ethernet switch (Intel XWAY PHY11G) will not come up
- Device problem occurs on: TP Link Archer VR200v (xRX200 rev 1.2)
- openwrt version: yesterday’s Snapshot r17264-774b386a92
- reproduce: (1) flash firmware via the webservice, (2) wait

 
05.08.20213966Base systemBug ReportVery LowLowAPU2 LEDs not workingopenwrt-21.02Unconfirmed Task Description

The 3 status LEDs of APU2 boards are not working neither with any 21.02-rc nor with own build.
It looks like there was a commit applied to master on 20.2.21 after the branching off 21.02 for file

target/linux/x86/base-files/etc/board.d/01-leds


that fixed that problem.
My own build with this file applied makes the LEDs work again.
Is it possible to cherry pick this file into the 21.02 branch before releasing 21.02.0?


03.08.20213965Base systemBug ReportVery LowLowMAC addresses should be kept as in 19.07openwrt-21.02Unconfirmed Task Description

Supply the following if possible:
- Device problem occurs on: WRT1200AC
- Software versions of OpenWrt/LEDE release, packages, etc.: 21.02
- Steps to reproduce: Clean install

After upgrading from 19.07 to 21.02 I found out issues with IP addresses given by my ISP. I found out that the MAC address of the WAN port has changed instead of LAN (before LAN started with 26 and WAN 24 but after upgrading it was the opposite - LAN started with 24 and WAN with 26). It is a very confusing behavior and addressing and IMO it should stay as it was in previous versions.

 


03.08.20213964PackagesBuild FailureVery LowMediumphp7.2.34-3 and 7.2.22-1 err on all systemAllUnconfirmed Task Description

Device problem occurs on arm_cortex-a9
Openwrt
php7.4.21 is ok.but 7.4.22-1 and 7.2.34-3 php7-fpm start failed
Linux version 4.9.77 (lede@ubuntu) (gcc version 5.5.0 (OpenWrt GCC 5.5.0 r6102-23a0f8aaad) )
and releases 19.07

 

opkg install php7 php7-cgi php7-fpm php7-mod-ctype php7-mod-curl php7-mod-exif php7-mod-filter php7-mod-gd php7-mod-iconv php7-mod-json php7-mod-ldap php7-mod-mbstring php7-mod-pdo php7-mod-session php7-mod-xml

have php7.4.22-1(2021-7-29new) and 7.2.34-3

opkg list-installed php7*
php7 - 7.2.34-3
php7-cgi - 7.2.34-3
php7-fastcgi - 7.2.34-3
php7-fpm - 7.2.34-3
php7-mod-ctype - 7.2.34-3
php7-mod-curl - 7.2.34-3
php7-mod-exif - 7.2.34-3
php7-mod-gd - 7.2.34-3
php7-mod-iconv - 7.2.34-3
php7-mod-json - 7.2.34-3
php7-mod-ldap - 7.2.34-3
php7-mod-mbstring - 7.2.34-3
php7-mod-pdo - 7.2.34-3
php7-mod-session - 7.2.34-3

dont have php7-mod-filter

root@OpenWrt:~# service php7-fpm restart
Error relocating /usr/bin/php-fpm: fopencookie: symbol not found
Error relocating /usr/bin/php-fpm: explicit_bzero: symbol not found

and

root@OpenWrt:~# opkg list-installed php7*
php7 - 7.4.22-1
php7-cgi - 7.4.22-1
php7-fpm - 7.4.22-1
php7-mod-ctype - 7.4.22-1
php7-mod-curl - 7.4.22-1
php7-mod-exif - 7.4.22-1
php7-mod-filter - 7.4.22-1
php7-mod-gd - 7.4.22-1
php7-mod-iconv - 7.4.22-1
php7-mod-json - 7.4.22-1
php7-mod-ldap - 7.4.22-1
php7-mod-mbstring - 7.4.22-1
php7-mod-pdo - 7.4.22-1
php7-mod-session - 7.4.22-1
php7-mod-xml - 7.4.22-1


root@OpenWrt:~# service php7-fpm restart
Error relocating /usr/bin/php-fpm: fopencookie: symbol not found
Error relocating /usr/bin/php-fpm: explicit_bzero: symbol not found

02.08.20213963Base systemBug ReportVery LowHighOdhcpd relayed RA causing wifi drops for android 11TrunkUnconfirmed Task Description

odhcpd ipv6 with ra relay causes android 11 (tested with multiple devices) to loop connect and disconnect.

Another person also reported in the githib mirror - sorry if linking is not allowed (https://github.com/openwrt/odhcpd/issues/166).

I ll attach logs when able to as atm have a 4/32 device with no logging.

02.08.20213962Base systemBug ReportVery LowMediumMMC on RUT955 does not workTrunkUnconfirmed Task Description

For details, pls refere to

https://forum.openwrt.org/t/rut955-how-to-use-mmc/102727

Reproducable at will: Appropiate device for MMC not found. Impossible, to access microSD-card.

02.08.20213961Base systemBug ReportVery LowLowAtheros WDS stopped working on TP-Link Archer C60 v2 wi...TrunkUnconfirmed Task Description

I tried rc4 of OpenWRT 21.02.0 on my Atheros C60 v2 and WDS stopped working.
WDS is used for forwarding a wired client on the same subnet of the wifi network.
I found the wireless client associated to my Atheros C60 access point

Mon Aug  2 15:46:45 2021 daemon.info hostapd: wlan1-1: STA xxx IEEE 802.11: authenticated
Mon Aug  2 15:46:45 2021 daemon.info hostapd: wlan1-1: STA xxxx IEEE 802.11: associated (aid 1)

but I’m unable even to ping it.
Even if I set up a fixed IP address on both the wireless and the wired clients, they can’t connect to the router.
Other clients are connected to the Atheros C60 access point without problems.
I never had a problem with previous version of OpenWRT, so I went back to rc3 and everything started working again.

The only extra package installed is relayd

/etc/config/network on Archer C60

config interface 'loopback'
        option proto 'static'
        option ipaddr '127.0.0.1'
        option netmask '255.0.0.0'
        option device 'lo'

config globals 'globals'

config interface 'wan'
        option proto 'dhcp'
        option device 'eth1'

config interface 'wan6'
        option proto 'dhcpv6'
        option device 'eth1'

config interface 'lan'
        option proto 'static'
        option netmask '255.255.255.0'
        option ipaddr '192.168.50.1'
        option gateway '192.168.2.1'
        list dns '192.168.2.5'
        option device 'br-lan'

config switch
        option name 'switch0'
        option reset '1'
        option enable_vlan '1'

config switch_vlan
        option device 'switch0'
        option vlan '1'
        option ports '1 2 3 4 0t'

config interface 'wwan'
        option proto 'static'
        option netmask '255.255.255.0'
        list dns '192.168.2.5'
        option ipaddr '192.168.2.50'
        option gateway '192.168.2.1'

config interface 'repeater_bridge'
        option proto 'relay'
        list network 'lan'
        list network 'wwan'
        option gateway '192.168.2.5'

config device
        option name 'br-lan'
        option type 'bridge'
        list ports 'eth0.1'

/etc/config/wireless on Archer C60

config wifi-device 'radio0'
        option type 'mac80211'
        option hwmode '11a'
        option path 'pci0000:00/0000:00:00.0'
        option htmode 'VHT80'
        option country 'IT'
        option channel '60'
        option cell_density '0'

config wifi-iface 'default_radio0'
        option device 'radio0'
        option network 'lan'
        option mode 'ap'
        option ssid 'xxx'
        option encryption 'psk2+ccmp'
        option key ''

config wifi-device 'radio1'
        option type 'mac80211'
        option hwmode '11g'
        option htmode 'HT20'
        option country 'IT'
        option channel 'auto'
        option path 'platform/ahb/18100000.wmac'

config wifi-iface 'default_radio1'
        option device 'radio1'
        option network 'lan'
        option mode 'ap'
        option wds '1'
        option ssid 'xxx'
        option encryption 'psk2+ccmp'
        option key ''

config wifi-iface 'wifinet2'
        option ssid 'xxx'
        option device 'radio1'
        option mode 'sta'
        option key ''
        option network 'wwan'
        option encryption 'psk2'
        option bssid 'xxx'


01.08.20213960Base systemBug ReportVery LowLowXiaomi MiWifi Nano 3C/ R3C/ R3L dts mismatch causes the...openwrt-19.07Unconfirmed Task Description

Supply the following if possible:
- Device problem occurs on
Xiaomi MiWifi R3L
- Software versions of OpenWrt/LEDE release, packages, etc.
OpenWrt v19.07.7
- Steps to reproduce
1) From the Wiki at https://openwrt.org/toh/xiaomi/mir3c flash the sysupgrade image: http://downloads.openwrt.org/releases/19.07.7/targets/ramips/mt76x8/openwrt-19.07.7-ramips-mt76x8-miwifi-nano-squashfs-sysupgrade.bin 2) Device does not boot anymore

The problem is the dts MIWIFI-NANO.dts defines a incompatible layout of the flash, which ends up flashing OpenWrt to the wrong part of the flash.
The OEM partition layout is:

[    1.510000] 0x000000000000-0x000001000000 : "ALL"
[    1.510000] 0x000000000000-0x000000030000 : "Bootloader"
[    1.520000] 0x000000030000-0x000000040000 : "Config"
[    1.530000] 0x000000040000-0x000000050000 : "Bdata"
[    1.530000] 0x000000050000-0x000000060000 : "Factory"
[    1.540000] 0x000000060000-0x000000070000 : "crash"
[    1.550000] 0x000000070000-0x000000080000 : "cfg_bak"
[    1.550000] 0x000000080000-0x000000140000 : "overlay"
[    1.560000] 0x000000140000-0x0000008a0000 : "OS1"
[    1.610000] 0x0000002a0000-0x0000008a0000 : "rootfs"
[    1.610000] 0x0000008a0000-0x000001000000 : "OS2"

with emphasis on OS1 and OS2.

However MIWIFI-NANO.dts defines firmware partition as:

                        partition@50000 {
                                compatible = "denx,uimage";
                                label = "firmware";
                                reg = <0x50000 0xfb0000>;

                        };

The bootloader will boot either OS1 or OS2 → we get an unbootable device.

Now we have two similar devices, MiWifi Nano R1 and R3L/R3C with different partition layout but the wiki proposes to flash the same image: https://openwrt.org/toh/xiaomi/mir3c https://openwrt.org/toh/xiaomi/miwifi_nano I personally still use my R3L so I would propose we add a new device type that could cover R3L.


01.08.20213959Base systemBug ReportVery LowLowAdding 802.11s mesh network to Archer C7 does not work ...TrunkUnconfirmed Task Description

Supply the following if possible:
- Device problem occurs on

  TP-Link Archer C7 v2, Archer C7 v5

- Software versions of OpenWrt/LEDE release, packages, etc.

  21.02_rc3 
  (downloaded from here: 
  - https://firmware-selector.openwrt.org/?version=21.02.0-rc3&target=ath79%2Fgeneric&id=tplink_archer-c7-v2, 
  - https://firmware-selector.openwrt.org/?version=21.02.0-rc3&target=ath79%2Fgeneric&id=tplink_archer-c7-v5)

- Steps to reproduce

1. Flash router with prepared image
2. replace wpad-mesh with wpad-mesh-wolfssl (why on earth did you replace openssl with wolfssl?)
2. Create an 802.11s Mesh Point

→ with the default images, wireless is not associated
→ 802.11s link is not established

- Steps to remedy

replace

  ath10k-firmware-qca988x-ct

with

  ath10k-firmware-qca988x

reboot

Mesh network will get associated to the wlan device, mesh starts to work

Wish:
Please replace firmware in standard images as this error is not easy to identify and find a fix.


30.07.20213957Base systemBug ReportVery LowCriticalWAN port broken on WNDR3800openwrt-21.02Unconfirmed Task Description

Supply the following if possible:
- Netgear WNDR3800-1CHNAS
- OpenWrt 21.02-SNAPSHOT r16247-60fad8f82b
- Steps to reproduce:

  • Flash from stock to OpenWRT 19.07.x ATH79
  • Flash from 19.07.x to OpenWRT 21.02-SNAPSHOT
  • Reset to factory in GUI
  • WAN never comes up, it never leaves “UP BROADCAST MULTICAST” according to ifconfig.
  • WAN port is always flapping, nothing is logged on kernel/system logs.

The hardware was checked before flashing, in OEM firmware WAN is working.

As shown below one of the ports has a blank uid value (full zeros).

(Attached is a full copy of kernel log.

[ 1.192635] ag71xx 19000000.eth: connected to PHY at fixed-0:00 [uid=00000000, driver=Generic PHY]
[ 1.202218] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode: rgmii
[ 1.524463] ag71xx 1a000000.eth: connected to PHY at rtl8366s:04 [uid=001cc960, driver=Generic PHY]
[ 1.534115] eth1: Atheros AG71xx at 0xba000000, irq 5, mode: rgmii

28.07.20213954KernelBuild FailureVery LowVery LowSATA Port Multiplier supportopenwrt-19.07Unconfirmed Task Description

Supply the following if possible:

Impossible to see all my hard drive (I only see 4):

  • Marvell Technology Group Ltd. 88SE9235 PCIe 2.0 x2 4-port SATA 6 Gb/s Controller (rev 11)

Could you enable this option during kernel compilation please:

CONFIG_SATA_PMP=y

like in this target : mvebu: enable SATA port multiplier support

Thanks in advance, I’m stuck in mounting my router because of this

Cordially

 


28.07.20213953Base systemBug ReportVery LowMediumWireguard slow performance - mpc85xx (Tp-Link WDR-4900)...openwrt-21.02Unconfirmed Task Description

With openwrt-21.02-rc3 the wireguard vpn speed is quite slow ~ 50 Mbps, compared to 19.07.7 where I get 100 Mbps.
My hardware is Tp-Link WDR-4900 - mpc85xx.

26.07.20213951Base systemBug ReportVery LowCriticalAP inaccessible after https://github.com/openwrt/openwr...openwrt-21.02Unconfirmed Task Description

Supply the following if possible:
- mir3g and mi4a gigabit edition mt7621 devices.. a dlink dir 882 remained accessible but all other ports seem down..
- openwrt https://github.com/openwrt/openwrt/commit/089efd61e9a6cdc0ea39c184d37bc8ebbe03175c - flash latest master or latest 21.02 makes device unreachable had to hard flash stock again and flash older openwrt

 


26.07.20213950Base systemBug ReportVery LowLowSwitch is not working on Asus RT-AC65P with latest snap...TrunkUnconfirmed Task Description

Supply the following if possible:
- Device problem occurs on: Asus RT-AC65P
- Software versions of OpenWrt/LEDE release, packages, etc.: OpenWrt SNAPSHOT r17216-8c2509dc5f
- Steps to reproduce:
Install the snapshot as a fresh install or as a sysupgrade.
Connect a PC to any LAN port except the 1st one.
Try pinging the router or any device in the same network.
Getting error: PING: transmit failed. General failure.
At the same time the 1st port of LAN is working properly. WAN is also working.

Reverting back to an old snapshot fixes the issue. I have only one from July 2020 so I can’t say when the issue appeared.

 


25.07.20213948KernelBug ReportVery LowCriticalath10k not working on clearfog pro with openwrt-21.02openwrt-21.02Unconfirmed Task Description

Supply the following if possible:
- Device problem occurs on
SolidRun Clearfog Pro A1

- Software versions of OpenWrt/LEDE release, packages, etc.
openwrt branch 21.02

- Steps to reproduce
boot it with a compex wle600 or wle900 pcie wifi card and it will report something like:

[  683.019493] ath10k_pci 0000:02:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[  683.265291] ath10k_pci 0000:02:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000
[  683.274540] ath10k_pci 0000:02:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[  683.284178] ath10k_pci 0000:02:00.0: firmware ver 10.2.4-1.0-00047 api 5 features no-p2p,raw-mode,mfp,allows-mesh-bcast crc32 35bd9258
[  683.342118] ath10k_pci 0000:02:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
[  685.564553] ath10k_pci 0000:02:00.0: failed to receive control response completion, polling..
[  686.604459] ath10k_pci 0000:02:00.0: Service connect timeout
[  686.610136] ath10k_pci 0000:02:00.0: failed to connect htt (-110)
[  686.725295] ath10k_pci 0000:02:00.0: could not init core (-110)
[  686.731257] ath10k_pci 0000:02:00.0: could not probe fw (-110)

I configured the kernel with CONFIG_PACKAGE_ath10k-board-qca988x=y and CONFIG_PACKAGE_ath10k-firmware-qca988x=y

In openwrt 19.x i get:

 OpenWrt 19.07.7, r11306-c4a6851c72
 -----------------------------------------------------
root@OpenWrt:~# dmesg | grep ath
[   11.207948] ath10k_pci 0000:02:00.0: enabling device (0140 -> 0142)
[   11.214444] ath10k_pci 0000:02:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[   11.454635] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:02:00.0.bin failed with error -2
[   11.465380] ath10k_pci 0000:02:00.0: Falling back to user helper
[   11.507440] firmware ath10k!pre-cal-pci-0000:02:00.0.bin: firmware_loading_store: map pages failed
[   11.516611] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/cal-pci-0000:02:00.0.bin failed with error -2
[   11.527009] ath10k_pci 0000:02:00.0: Falling back to user helper
[   11.537130] firmware ath10k!cal-pci-0000:02:00.0.bin: firmware_loading_store: map pages failed
[   11.545913] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/firmware-6.bin failed with error -2
[   11.556650] ath10k_pci 0000:02:00.0: Falling back to user helper
[   11.566721] firmware ath10k!QCA988X!hw2.0!firmware-6.bin: firmware_loading_store: map pages failed
[   11.623287] ath10k_pci 0000:02:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043222ff sub 0000:0000
[   11.632549] ath10k_pci 0000:02:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
[   11.642078] ath10k_pci 0000:02:00.0: firmware ver 10.2.4-1.0-00047 api 5 features no-p2p,raw-mode,mfp,allows-mesh-bcast crc32 35bd9258
[   11.686880] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/board-2.bin failed with error -2
[   11.697349] ath10k_pci 0000:02:00.0: Falling back to user helper
[   11.707724] firmware ath10k!QCA988X!hw2.0!board-2.bin: firmware_loading_store: map pages failed
[   11.720044] ath10k_pci 0000:02:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
[   12.859296] ath10k_pci 0000:02:00.0: htt-ver 2.1 wmi-op 5 htt-op 2 cal otp max-sta 128 raw 0 hwcrypto 1
[   12.992322] ath: EEPROM regdomain: 0x0
[   12.992325] ath: EEPROM indicates default country code should be used
[   12.992327] ath: doing EEPROM country->regdmn map search
[   12.992330] ath: country maps to regdmn code: 0x3a
[   12.992333] ath: Country alpha2 being used: US
[   12.992334] ath: Regpair used: 0x3a
[   14.794232] ath: EEPROM regdomain: 0x82f4
[   14.804051] ath: EEPROM indicates we should expect a country code
[   14.810159] ath: doing EEPROM country->regdmn map search
[   14.815521] ath: country maps to regdmn code: 0x37
[   14.820326] ath: Country alpha2 being used: CH
[   14.824790] ath: Regpair used: 0x37
[   14.828285] ath: regdomain 0x82f4 dynamically updated by user
[   17.571688] ath10k_pci 0000:02:00.0: pdev param 0 not supported by firmware

I tried it also with the -ht firmware in v21_02 but still no luck.
Here https://githubmemory.com/repo/greearb/ath10k-ct/issues/148 someone mentioned that this might be a problem with SolidRun’s PCIe implementation (if i understood that correctly).

24.07.20213947KernelBug ReportVery LowCriticalWifi STA that loses AP signal takes down the whole rout...openwrt-21.02Unconfirmed Task Description

Initially reported on forum: https://forum.openwrt.org/t/wifi-client-disconnecting-takes-the-whole-wifi-ap-down-on-21-02-snapshot-how-to-debug/102094/8

Device: Asus RT-N56U
Branch: openwrt-21.02, initial report commit 60fad8f (v21.02.0-rc3-74-g60fad8f82b)

Observation: when a wifi client disconnects that appears to see the AP with low signal strength, the whole AP goes down. Verified with airmon/tcpdump that AP beacons stop. Reboot of the router also observed when log_level set to 2 or lower.

Bisecting, commit https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=a078037ace50 (v21.02.0-rc3-35-ga078037ace) seems to be the issue:

    mac80211: improve rate control performance

    Call rate control handler after intermediate queueuing
    Includes follow-up fixes

Test case:

1. Connect to AP
2. Move far away or shield mobile so the AP signal drops significantly as seen by mobile
3. Viewing the wifi networks of the mobile (android), if when signal drops below some threshold:
4.1 AP disappears from list: FAIL [the router also reboots]
4.2 AP moves from “Connected” to “Saved”: PASS

I did not have these issues at all in May 2021 using the dev snapshot. I updated to the July 2021 dev snapshot, observed the issue, then built openwrt-21.02 and still observed the issue.

21.07.20213946PackagesBug ReportVery LowCritical lldpd needs update to fix CVE-2020-27827openwrt-19.07Unconfirmed Task Description

the current verion 1.0.3 on 19.07 needs a update to fix CVE-2020-27827

read https://github.com/lldpd/lldpd/releases

20.07.20213944Base systemBug ReportVery LowLowOctegon can't read timezoneopenwrt-21.02Unconfirmed Task Description

EdgeRouter-4 21.02-snapshot-r16232-febf6db0d0 (and other Octegon devices as seen it the forum thread).

I can’t get the EdgeRouter-4 to read the /etc/tz file. The file exist and I can read it from PuTTy. The /etc/tz changes to the correct time zone every time I in LuCi system settings change time zone.
I have also tried installing the Europe time zone package in hope for good luck but without any luck.

No matter what I do the system time in LuCi overview, date command and system log always show UTC time!? But the time in LuCi system time settings read the correct local time.

Fault tread from the OpenWRT forum

root@[sanitized]:~# uci show system; readlink -f /etc/TZ
system.@system[0]=system
system.@system[0].ttylogin='0'
system.@system[0].urandom_seed='0'
system.@system[0].hostname='[sanitized]'
system.@system[0].description='[sanitized]'
system.@system[0].log_file='/Logs/system.log'
system.@system[0].log_size='640'
system.@system[0].log_proto='udp'
system.@system[0].conloglevel='8'
system.@system[0].cronloglevel='5'
system.@system[0].zonename='Europe/Stockholm'
system.@system[0].timezone='CET-1CEST,M3.5.0,M10.5.0/3'
system.ntp=timeserver
system.ntp.server='0.openwrt.pool.ntp.org' '1.openwrt.pool.ntp.org' '2.openwrt.pool.ntp.org' '3.openwrt.pool.ntp.org'
/tmp/TZ
root@[sanitized]:~#
root@[sanitized]:~# cat /etc/TZ
CET-1CEST,M3.5.0,M10.5.0/3
root@[sanitized]:~#
root@[sanitized]:~# cat /tmp/TZ
CET-1CEST,M3.5.0,M10.5.0/3
root@[sanitized]:~#

There have been some fault finding already pointing to a fault in the code?
External Link

20.07.20213942Base systemBug ReportVery LowHighI report a bug [21.02-rc3 ]openwrt-21.02Unconfirmed Task Description

I report a bug. After testing, openwrt 21.02-rc3 version: the interface protocol “PPPoE” severely limits the network speed, or “the network speed is seriously not up to the speed provided by the service provider“.

The test results are as follows:

My device is tp link Archer C7

I use 300m broadband network for testing, download the same link resources, the new version 21.02-rc3 speed is only 26m, using the old version 19.07. X test, download speed can reach 40m, and very stable.


20.07.20213941KernelBug ReportVery LowCriticalBanana Pi M2 Ultra follow in endless rebooting with lat...TrunkUnconfirmed Task Description

Supply the following if possible:
- Device problem occurs on
- Software versions of OpenWrt/LEDE release, packages, etc.
- Steps to reproduce

 

Device: Banana Pi M2 Ultra
OpenWrt: Snapshot image from https://downloads.openwrt.org/snapshots/targets/sunxi/cortexa7/ Steps:

1. uncompressed downloaded file
2. dd to TF card
3. Put this TF card into board’s TF slot
4. Using usb-serial converter connects to its debug uart pins
5. Power on M2U board
6. Watch the boot log

  [    1.376746] libphy: stmmac: probed
  [    1.389128] mmc1: queuing unknown CIS tuple 0x80 (2 bytes)
  [    1.394664] mmc0: host does not support reading read-only switch, assuming write-enable
  [    1.402844] mmc0: new SDHC card at address 0001
  [    1.408341] mmcblk0: mmc0:0001 SD8GB 7.28 GiB 
  [    1.414442] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
  [    1.419981]  mmcblk0: p1 p2
  [    1.426302] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
  [   
  U-Boot SPL 2020.04 (Jul 20 2021 - 03:16:48 +0000)
  DRAM: 2048 MiB
  Trying to boot from MMC1
19.07.20213940Base systemBug ReportVery LowLowRead only / filesystem after power lossTrunkUnconfirmed Task Description

Hi all,

Virtual machine x86 builded with image builder and
version 21.02.0-rc3 with package softethervpn-server - 4.34-9745-1

suddenly occurs with read only filesystem /

root@OpenWrt:/# mount
/dev/root on / type ext4 (ro,noatime)
.
.

after check and random errors in fs (mostly related with softether vpn server):

root@OpenWrt:/# mount
/dev/root on / type ext4 (rw,noatime)
.
.
free space is:
root@OpenWrt:/# df -h
Filesystem Size Used Available Use% Mounted on
/dev/root 220.5M 31.7M 184.3M 15% /
.
.

In working old 15 version:

root@OpenWrt:/# cat /etc/openwrt_version
15.05.1
root@OpenWrt:/# mount
rootfs on / type rootfs (rw)
/dev/root on / type ext4 (rw,noatime,data=ordered)
.
.

Do I have to make it data=ordered to prevent data and fs problems and how?

Thanks in advance?

19.07.20213938Base systemBug ReportVery LowCriticalAkitio MyCloud Mini hangs during boot of akitio_mycloud...openwrt-21.02Unconfirmed Task Description

Supply the following if possible:

 

The akitio_mycloud-initramfs-uImage from 21.02.0-rc3 hangs when booting on Akitio MyCloud Mini. This was also reported as an issue in the forums with 19.07 release.

Stage-1 Bootloader 五 10月 28 10:36:29 CST 2011
Attempting to set PLLA to 750MHz ...
  plla_ctrl0 : 0x0000000A
  plla_ctrl1 : 0x000F0000
  plla_ctrl2 : 0x001D01A0
  plla_ctrl3 : 0x00000017
PLLA Set

Setup memory, testing, Image 0
  Hdr len: 0x0001AC3C
  Hdr CRC: 0xB931AD17
 OK


U-Boot 1.1.2 (Oct 28 2011 - 10:44:29)

U-Boot code: 60D00000 -> 60D1AC3C  BSS: -> 60D1F2F4
RAM Configuration:
        Bank #0: 60000000 256 MB
SRAM Configuration:
        64KB at 0x50000000
NAND:256 MiB
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Setting Linux mem= boot arg value
Reading upgrade flag from NAND address 0x01ec0000 : 0
Hit any key to stop autoboot:  0 
$ tftp 64000000 uImage.mycloud
Wait GMAC to reset
Wait for PHY reset
PHY is Realtek RTL8211D
Wait for link to come up................Link up
Wait for auto-negotiation to complete
Link is 1000M
TFTP from server 192.168.50.59; our IP address is 192.168.50.100
Filename 'uImage.mycloud'.
Load address: 0x64000000
Loading: 
ARP Resend request
T invalid RARP header
################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         ##########################
done
Bytes transferred = 7120489 (6ca669 hex)
$ bootm 64000000
## Booting image at 64000000 ...
   Image Name:   ARM OpenWrt Linux-5.4.124
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    7120425 Bytes =  6.8 MB
   Load Address: 60008000
   Entry Point:  60008000
   Verifying Checksum ... OK
OK

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 5.4.124 (builder@buildhost) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r16172-2aba3e9784)) #0 SMP Sun Jun 13 22:02:19 2021
[    0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5787d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt: Machine model: Akitio MyCloud
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] cma: Reserved 64 MiB at 0x64000000
[    0.000000] percpu: Embedded 15 pages/cpu s29772 r8192 d23476 u61440
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32480
[    0.000000] Kernel command line: earlyprintk console=ttyS0,115200
[    0.000000] Bootloader command line (ignored): root=ubi0:rootfs ubi.mtd=2,512 rootfstype=ubifs console=ttyS0,115200 elevator=cfq mac_adr=0x00,0x30,0xe0,0x00,0x00,0x01 mem=256M poweroutage=yes
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 47188K/131072K available (6144K kernel code, 171K rwdata, 784K rodata, 9216K init, 214K bss, 18348K reserved, 65536K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000] rcu:     RCU event tracing is enabled.
[    0.000000] rcu:     RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=2.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] FPGA IRQ chip 0 "interrupt-controller" @ (ptrval), 32 irqs, parent IRQ: 16
[    0.000000] random: get_random_bytes called from 0xc0800b88 with crng_init=0
[    0.000020] sched_clock: 24 bits at 390kHz, resolution 2560ns, wraps every 21474835200ns
[    0.000074] clocksource: oxnas_rps_clocksource_timer: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 19112603332 ns
[    0.000089] timer_oxnas_rps: Registered clocksource rate 390625Hz
[    0.000112] timer_oxnas_rps: Registered clock event rate 6250000Hz prescaler 0 period 62500
[    0.000276] GIC: PPI13 is secure or misconfigured
[    0.000330] GIC: PPI13 is secure or misconfigured
[    0.000450] Calibrating delay loop... 298.59 BogoMIPS (lpj=1492992)
[    0.070307] pid_max: default: 32768 minimum: 301
[    0.070661] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.070689] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.072107] CPU: Testing write buffer coherency: ok
[    0.074155] Setting up static identity map for 0x60100000 - 0x6010005c
[    0.074457] rcu: Hierarchical SRCU implementation.
[    0.075202] smp: Bringing up secondary CPUs ...
[    0.076308] GIC: PPI13 is secure or misconfigured
[    0.140692] smp: Brought up 1 node, 2 CPUs
[    0.140728] SMP: Total of 2 processors activated (598.42 BogoMIPS).
[    0.146245] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.146286] futex hash table entries: 512 (order: 2, 16384 bytes, linear)
[    0.153093] pinctrl core: initialized pinctrl subsystem
[    0.154055] NET: Registered protocol family 16
[    0.158021] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.160611] cpuidle: using governor menu
[    0.160719] No ATAGs?
[    0.181959] pps_core: LinuxPPS API ver. 1 registered
[    0.181982] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.182041] PTP clock support registered
[    0.182300] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512
[    0.183626] clocksource: Switched to clocksource oxnas_rps_clocksource_timer
[    0.185013] thermal_sys: Registered thermal governor 'step_wise'
[    0.185392] NET: Registered protocol family 2
[    0.185592] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
[    0.187010] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[    0.187092] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.187130] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear)
[    0.187169] TCP: Hash tables configured (established 1024 bind 1024)
[    0.187343] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.187412] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.187837] NET: Registered protocol family 1
[    0.187896] PCI: CLS 0 bytes, default 32
[    0.487014] workingset: timestamp_bits=14 max_order=15 bucket_order=1
[    0.498406] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.499348] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
[    0.502737] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.506877] printk: console [ttyS0] disabled
[    0.507051] 44200000.serial: ttyS0 at MMIO 0x44200000 (irq = 55, base_baud = 390625) is a 16550A
[    0.967037] printk: console [ttyS0] enabled
[    0.989649] brd: module loaded
[    1.004014] loop: module loaded
[    1.073950] Could not find a valid ONFI parameter page, trying bit-wise majority to recover it
[    1.082611] ONFI parameter recovery failed, aborting
[    1.087621] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xda
[    1.093977] nand: Hynix NAND 256MiB 3,3V 8-bit
[    1.098403] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    1.105996] Scanning device for bad blocks
[    1.161538] Bad eraseblock 618 at 0x000004d40000
[    1.183211] Bad eraseblock 824 at 0x000006700000
[    1.190617] Bad eraseblock 858 at 0x000006b40000
[    1.251353] Bad eraseblock 1536 at 0x00000c000000
[    1.271260] Bad eraseblock 1720 at 0x00000d700000
[    1.295429] Bad eraseblock 1955 at 0x00000f460000
[    1.307783] 2 fixed-partitions partitions found on MTD device 41000000.nand-controller
[    1.315706] Creating 2 MTD partitions on "41000000.nand-controller":
[    1.322055] 0x000000000000-0x0000026c0000 : "boot"
[    1.328936] 0x0000026c0000-0x000010000000 : "ubi"
[    1.337172] libphy: Fixed MDIO Bus: probed
[    1.342082] oxnas-dwmac 40400000.ethernet: IRQ eth_lpi not found
[    1.348318] oxnas-dwmac 40400000.ethernet: PTP uses main clock
[    1.354201] oxnas-dwmac 40400000.ethernet: no reset control found
[    1.424023] oxnas-dwmac 40400000.ethernet: User ID: 0x12, Synopsys ID: 0x35
[    1.430981] oxnas-dwmac 40400000.ethernet:   DWMAC1000
[    1.436070] oxnas-dwmac 40400000.ethernet: DMA HW capability register supported
[    1.443345] oxnas-dwmac 40400000.ethernet: RX Checksum Offload Engine supported
[    1.450659] oxnas-dwmac 40400000.ethernet: COE Type 2
[    1.455723] oxnas-dwmac 40400000.ethernet: TX Checksum insertion supported
[    1.462563] oxnas-dwmac 40400000.ethernet: Wake-Up On Lan supported
[    1.468899] oxnas-dwmac 40400000.ethernet: Enhanced/Alternate descriptors
[    1.475706] oxnas-dwmac 40400000.ethernet: Enabled extended descriptors
[    1.482291] oxnas-dwmac 40400000.ethernet: Ring mode enabled
[    1.487953] oxnas-dwmac 40400000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[    1.495815] oxnas-dwmac 40400000.ethernet: device MAC address 3e:c3:3f:d1:0c:ca
[    1.536033] libphy: stmmac: probed
[    1.539445] RTL8211DN Gigabit Ethernet stmmac-0:00: attached PHY driver [RTL8211DN Gigabit Ethernet] (mii_bus:phy_addr=stmmac-0:00, irq=POLL)
[    1.552128] RTL8211DN Gigabit Ethernet stmmac-0:03: attached PHY driver [RTL8211DN Gigabit Ethernet] (mii_bus:phy_addr=stmmac-0:03, irq=POLL)
[    1.567016] ledtrig-cpu: registered to indicate activity on CPUs
[    1.573120] hidraw: raw HID events driver (C) Jiri Kosina
[    1.580288] NET: Registered protocol family 10
[    1.586462] Segment Routing with IPv6
[    1.590225] NET: Registered protocol family 17
[    1.594862] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    1.607805] 8021q: 802.1Q VLAN Support v1.8

Device hangs at this point.

19.07.20213937Base systemBug ReportVery LowMediumMR32 BCM53xx boot erroropenwrt-21.02Unconfirmed Task Description

I have an MR32 I’m trying to flash. Following the instructions on https://openwrt.org/toh/meraki/mr32 I uploaded the initramfs successfully to part.safe. When rebooting the console has the following errors then boots back into the Meraki firmware:

[ 4.690000] Mapping 10362880 bytes for /dev/mtdblock/part.safe
[ 4.730000] find_itb_subimage: error finding kernel@1: FDT_ERR_NOTFOUND
[ 4.740000] find_itb_subimage: error finding ramdisk@1: FDT_ERR_NOTFOUND
[ 4.750000] find_itb_subimage: error finding fdt@2: FDT_ERR_NOTFOUND
[ 4.750000] kexec_raw: kexec_load: Cannot assign requested address
[ 6.490000] Mapping 10235904 bytes for /dev/mtdblock/part.old
[ 6.530000] Meraki-build is 23-191963

I built the initramfs from the current git master (7/18/2021). I also had someone on #openwrt-dev build it and I tried theirs and received the same errors.


14.07.20213934Base systemBug ReportVery LowHighWireless Wan loosing packets when pppoe-wan is upopenwrt-21.02Unconfirmed Task Description

Supply the following if possible:
- Device problem occurs on: Home Hub 5, Linksys EA8300, Linksys WRT32x
- Software versions of OpenWrt 21.02-rc3
- Steps to reproduce:

Configure pppoe-wan and wwan to your ISPs

Bring up wwan
# ping -I wwan0 8.8.8.8
all good.

Now bring up wan (pppoe-wan)
# ifup wan

ping -I wwan0 8.8.8.8 looses packets in initial pings as follows:

# ping -c10 -Iwwan0 8.8.8.8
PING 8.8.8.8 (8.8.8.8): 56 data bytes
64 bytes from 8.8.8.8: seq=4 ttl=113 time=201.142 ms
64 bytes from 8.8.8.8: seq=5 ttl=113 time=41.131 ms
64 bytes from 8.8.8.8: seq=6 ttl=113 time=50.998 ms
64 bytes from 8.8.8.8: seq=7 ttl=113 time=40.956 ms
64 bytes from 8.8.8.8: seq=8 ttl=113 time=50.932 ms
64 bytes from 8.8.8.8: seq=9 ttl=113 time=40.753 ms

— 8.8.8.8 ping statistics — 10 packets transmitted, 6 packets received, 40% packet loss
round-trip min/avg/max = 40.753/70.985/201.142 ms

As a consequence wwan gets disabled by mwan3 because the test pings always fail.

If I take down wan (ifdown wan), then ping through wwan0 works normally.

The same configuration was working fine in 19.07 therefore something was changed in 21.02 that causes this issue with the wireless wan network. I am not sure however if this is related to “Wireless Wan”, but I do not have a second wan of ethernet type that I can test this issue with.

Excerpt from /etc/config/network relative to the interfaces:

config interface ‘wan’

  option device 'wan'
  option proto 'pppoe'
  option username 'vodafonedsl'
  option password 'vodafonedsl'
  option metric '1'
  option ipv6 '0'
  option delegate '0'

config interface ‘wwan’

  option proto 'ncm'
  option device '/dev/cdc-wdm0'
  option pdptype 'IP'
  option apn 'web.omnitel.it'
  option service 'preferlte'
  option ipv6 '0'
  option metric '5'
 

The only solution right now is to return to 19.07 that works flawlessly with the same configuration.
Tested with 3 different router (as specified above), all giving the same result.

13.07.20213932Base systemBug ReportVery LowCritical[21.02] Autonegotiation speed fails with my provider's ...openwrt-21.02Unconfirmed Task Description

Supply the following if possible:
- Device problem occurs on: xiaomi mir3g
- 21.02 rc3
- My provider uses pppoe, cable is 4-wire 100baseT and my router is 1000baseT xiaomi mir3g

 

openwrt 21.02 fails to establish pppoe link because of failing to autonegotiate (Speed: Unknown!, Link detected: no, etc):

# ethtool wan
Settings for wan:
	Supported ports: [ TP MII ]
	Supported link modes:   10baseT/Half 10baseT/Full 
	                        100baseT/Half 100baseT/Full 
	                        1000baseT/Full 
	Supported pause frame use: Symmetric Receive-only
	Supports auto-negotiation: Yes
	Supported FEC modes: Not reported
	Advertised link modes:  10baseT/Half 10baseT/Full 
	                        100baseT/Half 100baseT/Full 
	                        1000baseT/Full 
	Advertised pause frame use: Symmetric Receive-only
	Advertised auto-negotiation: Yes
	Advertised FEC modes: Not reported
	Speed: Unknown!
	Duplex: Unknown! (255)
	Port: MII
	PHYAD: 1
	Transceiver: external
	Auto-negotiation: on
	Supports Wake-on: d
	Wake-on: d
	Link detected: no

When I set autonegotiation to off and forced to 100baseT/Full, pppoe worked like a charm.

/usr/sbin/ethtool -s wan speed 100 duplex full autoneg off
# ethtool wan
Settings for wan:
	Supported ports: [ TP MII ]
	Supported link modes:   10baseT/Half 10baseT/Full 
	                        100baseT/Half 100baseT/Full 
	                        1000baseT/Full 
	Supported pause frame use: Symmetric Receive-only
	Supports auto-negotiation: Yes
	Supported FEC modes: Not reported
	Advertised link modes:  100baseT/Full 
	Advertised pause frame use: Symmetric Receive-only
	Advertised auto-negotiation: No
	Advertised FEC modes: Not reported
	Speed: 100Mb/s
	Duplex: Full
	Port: MII
	PHYAD: 1
	Transceiver: external
	Auto-negotiation: off
	Supports Wake-on: d
	Wake-on: d
	Link detected: yes
13.07.20213928ToolchainBug ReportVery LowMedium[OPKG] Track installed/removed packages and provide imp...AllUnconfirmed Task Description

I tried to use opkg with this script “opkg extras” for upgrading:
https://openwrt.org/docs/guide-user/installation/generic.sysupgrade#savingrestoring_user-installed_packages

IMHO such a script is really basic functionality and I should not have to execute such a script just to keep the installed packages on upgrade.
IMHO this would make upgrading OpenWRT a lot easier and I would also do it a lot more frequent (potentially fixing security issues faster).

As I talked about this in the forum, too, the author said:
> In addition, as the author of those pages, I’d like to point out that the method for tracking installed and removed packages can be greatly simplified if someone decides to integrate that functionality into Opkg.

So more systematic:

Problem

I may fear to upgrade my OpenWRT router due to the loss of installed packages.
The existing alternatives are not sufficient and hard to use, especially for an average user. E.g. you need to use SSH/the CLI.
The existing alternative did not 100%ly work in my case. It e.g. also installed all dependencies as manually installed packages as far as I see.
Code-wise/Technically the author said the current way is much more complicated than what could be done if that were integrated into opkg.

Suggestion

It would be nice if these OPGK extras and hotplug extras were an opkg package itself. This would also solve the reinstallation issue, because by definition, they would reinstall “themselves”.

11.07.20213927Base systemBug ReportVery LowCriticalOpenWrt 21.02.0-rc3 bricks Netgear WNDR3700 v4openwrt-21.02Unconfirmed Task Description

I saw the announcement on the website about the next stable release so like an idiot I went to upgrade the firmware. Router never came back, left it on overnight to see if it would eventually come up. I was upgrading from 19.07.7.

Breaking open the case I see a UART header and some pads for a JTAG but I’m not the guy to debug what broke. I just wanted to give someone else a heads up so they don’t lose their router, too.

The debricking guide is some random notes for people who jump into the hardware, not really organized in any understandable way.

https://openwrt.org/docs/guide-user/troubleshooting/generic.debrick

I like the line “The usual recovery methods have failed, forceing the user to to go to JTAG.” Like, where are the usual recovery methods listed? Not in the debricking guide, they aren’t.

Sorry, it’s just frustrating for a somewhat literate user like me (coming from LEDE, 20-ish years in IT/networking/sysadmin crap) that the debricking guide is useless for me. No “here’s the steps the OS takes to initialize” and “here’s where a safemode kicks in where you can set some TFTP or here’s where you pop into the serial connection via PuTTY” or like a general list of steps in order that you can attempt before working up to “ok solder a JTAG connector, here’s a DIGIKey part number to get you started.”

Tried Failsafe, Factory Reset, and Recovery all with no dice.

10.07.20213926Base systemBug ReportVery LowLowSupport EAP-SIMTrunkUnconfirmed Task Description

Hello,

As already described here: https://forum.turris.cz/t/802-1x-eap-sim-support/13610

OpenWrt don’t have enabled support for EAP-SIM authentication.

There is a dirty patch here: https://forum.openwrt.org/t/bug-wpa-supplicant-eap-sim-aka-support-compile-error/46771/7

But the author said it was never accepted. There is any reason not accepting this patch in upstream?

10.07.20213925Base systemBug ReportVery LowCriticalwgt634u: jffs2 Filesystem overwrites the bootloader par...openwrt-19.07Unconfirmed Task Description

Supply the following if possible:
- Device problem occurs on WGT643u
- Software versions of OpenWrt/LEDE OpenWrt 19.07
Steps to reproduce:
- after fresh install I installed some bigger packages then the system hangs
- a reboot with power off/on not working
- The serial/UART/Terminal of the box shows the bootloader stops because the param partition at the end of the flash was overwritten and the checksum was wrong

It seems the partition size of the jffs2 partition is wrong.

Linux side:
root@OpenWrt:/# cat /proc/partitions
major minor #blocks name

                                                                              
31        0        640 mtdblock0                                              
31        1       7424 mtdblock1                                              
31        2          2 mtdblock2                                              
31        3       1324 mtdblock3                                              
31        4       6097 mtdblock4                                              
31        5       3456 mtdblock5                                              
31        6        128 mtdblock6 -->param partition

root@OpenWrt:/# cat /proc/mtd
dev: size erasesize name
mtd0: 000a0000 00020000 “boot”
mtd1: 00740000 00020000 “firmware”
mtd2: 00000928 00000928 “loader”
mtd3: 0014b2bc 00020000 “linux”
mtd4: 005f4400 00020000 “rootfs”
mtd5: 00360000 00020000 “rootfs_data”
mtd6: 00020000 00020000 “nvram” –>bootloader param partition == 131072 bytes (Bootloader says 8KB...)

root@OpenWrt:/# mount
/dev/root on /rom type squashfs (ro,relatime)
proc on /proc type proc (rw,nosuid,nodev,noexec,noatime)
sysfs on /sys type sysfs (rw,nosuid,nodev,noexec,noatime)
tmpfs on /tmp type tmpfs (rw,nosuid,nodev,noatime)
tmpfs on /tmp/root type tmpfs (rw,noatime,mode=755)
overlayfs:/tmp/root on / type overlay (rw,noatime,lowerdir=/,upperdir=/tmp/root/upper,workdir=/tmp/root/wo)
tmpfs on /dev type tmpfs (rw,nosuid,relatime,size=512k,mode=755)
devpts on /dev/pts type devpts (rw,nosuid,noexec,relatime,mode=600,ptmxmode=000)
debugfs on /sys/kernel/debug type debugfs (rw,noatime)

UART/Terminal shows after boot:
[ 127.964107] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0×1985 not found at 0×00000000: 0x0c3b instead
[ 128.053636] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0×1985 not found at 0×00000004: 0x58cd instead
[ 128.063208] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0×1985 not found at 0×00000008: 0x54cc instead
[ 128.193636] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0×1985 not found at 0x0000000c: 0×6859 instead
[ 128.203202] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0×1985 not found at 0×00000010: 0x916a instead
[ 128.283363] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0×1985 not found at 0×00000014: 0x9d93 instead
[ 128.303639] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0×1985 not found at 0×00000018: 0x6b25 instead
[ 128.313209] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0×1985 not found at 0x0000001c: 0x54bb instead
[ 128.413768] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0×1985 not found at 0×00000020: 0xeacc instead
[ 128.423620] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0×1985 not found at 0×00000024: 0x8dc5 instead
[ 128.433144] jffs2: Further such events for this erase block will not be printed
[ 128.829317] jffs2: Empty flash at 0×00010004 ends at 0×00011000
[ 128.884133] jffs2: Empty flash at 0×00011004 ends at 0×00012000
[ 128.891154] jffs2: Empty flash at 0×00012004 ends at 0×00014000
[ 128.999749] jffs2_scan_eraseblock(): End of filesystem marker found at 0×20000
[ 129.133686] jffs2: Cowardly refusing to erase blocks on filesystem with no valid JFFS2 nodes
[ 129.142209] jffs2: empty_blocks 26, bad_blocks 0, c→nr_blocks 27

                                            

root@OpenWrt:/# reboot
root@OpenWrt:/# ^C

See on the UART/Terminal while power on and press CTRL-C long:

                                                                              

CFE version 1.0.34 for BCM95365R (32bit,SP,LE)
Build Date: Tue Feb 24 03:21:41 CST 2004 (root@jackylinux)
Copyright (C) 2000,2001,2002 Broadcom Corporation.

                                                                              

Add MAC client version(DNI).
Initializing Arena.
Initializing Devices.
et0: Broadcom BCM47xx 10/100 Mbps Ethernet Controller
CPU type 0×29007: 200MHz
Total memory: 0×2000000 bytes (32MB)

                                                                              

Total memory used by CFE: 0x81BB1280 - 0×82000000 (4517248)
Initialized Data: 0x81BB1280 - 0x81BB3E90 (11280)
BSS Area: 0x81BB3E90 - 0x81BB45D0 (1856)
Local Heap: 0x81BB45D0 - 0x81FB45D0 (4194304)
Stack Area: 0x81FB45D0 - 0x81FB65D0 (8192)
Text (code) segment: 0x81FB65E0 - 0x81FFFFB0 (301520)
Boot area (physical): 0x01B70000 - 0x01BB0000
Relocation Factor: I:E23B65E0 - D:01BB0280

                                                                              

configure vlans
*
* VLAN Driver initial
***
Process LAN port(2-5) vlan Architecture...
SUCCESS: trying to create VLAN 0 for switch
SUCCESS: trying to add LAN port

                                                                              

Process WAN port(2-5) vlan Architecture...
SUCCESS: trying to create VLAN 0 for switch
SUCCESS: trying to add WAN port
SUCCESS: enable ports success
configure vlans...done
Automatic startup canceled via Ctrl-C

                           

CFE> show devices
Device Name Description
——————- ———————————————————
uart0 NS16550 UART at 0×18000300
uart1 NS16550 UART at 0×18000400
flash0.boot New CFI flash at 1C000000 offset 00000000 size 384KB
flash0.config New CFI flash at 1C000000 offset 00060000 size 128KB
flash0.os New CFI flash at 1C000000 offset 00080000 size 7672KB
flash0.nvram New CFI flash at 1C000000 offset 007FE000 size 8KB —–>param partition for bootloader

please fix the jffs2 partition size!

10.07.20213923Base systemBug ReportVery LowLowEdgerouter4 port numbers out of synck in system logopenwrt-21.02Unconfirmed Task Description

Model Ubiquiti EdgeRouter 4
Architecture UBNT_E300 (CN7030p1.2-1000-AAP)
Firmware Version OpenWrt 21.02-SNAPSHOT r16232-febf6db0d0 / LuCI openwrt-21.02 branch git-21.188.55099-e52e1de

The forum post:
External Link

It seems that port numbers in system log is out of synck with hardware port numbers, for example this log text:

switch0: port 1(lan0)

This bug makes log errors like

Port 1 receive error code 7, packet dropped

very hard to find if the actual port is false flagged.

kern.notice kernel: [ 4979.972921] lan0: Link down
kern.info kernel: [ 4979.975979] switch0: port 1(lan0) entered disabled state
daemon.notice netifd: Network device 'lan0' link is down
kern.notice kernel: [ 5011.719291] lan0: 1000 Mbps Full duplex, port 1, queue 1
kern.info kernel: [ 5011.724648] switch0: port 1(lan0) entered blocking state
kern.info kernel: [ 5011.729976] switch0: port 1(lan0) entered forwarding state
daemon.notice netifd: Network device 'lan0' link is up
kern.notice kernel: [ 5035.272920] lan0: Link down
kern.info kernel: [ 5035.275978] switch0: port 1(lan0) entered disabled state
daemon.notice netifd: Network device 'lan0' link is down
kern.info kernel: [ 3594.470962] switch0: port 4(lan3) entered disabled state
daemon.notice netifd: Network device 'lan3' link is down
kern.notice kernel: [ 3615.941460] lan1: 1000 Mbps Full duplex, port 2, queue 2
kern.info kernel: [ 3615.946870] switch0: port 2(lan1) entered blocking state
kern.info kernel: [ 3615.952201] switch0: port 2(lan1) entered forwarding state
daemon.notice netifd: Network device 'lan1' link is up
08.07.20213921Base systemBug ReportVery LowHighWAVLINK WL-WN577A2 (Maginon WLR-755AC) still crashes un...openwrt-21.02Unconfirmed Task Description

Device problem occurs on: WAVLINK WL-WN577A2 / Maginon WL-755 / Winstars WS-WN577A2 / Winstars WS-WN566A2 (MT7628AN)

Software versions of OpenWrt/LEDE release, packages, etc.:
all released till now! (testet lately with 20.01-rc3-snapshot again)

Problem:

The WLR755AC-Device regulary crashes under high load (LAN → WLAN) when using OpenWRT (latest 20.01-rc3 snapshot).
Using the stock firmware the issue does not occur.

With normal or low load the device works relieable and stable.

But when put under high load like playing a fullhd video, copying a lot of data and iperf simultaneously over WLAN the device will crash after a while.
The surface of the case will get palpable warm.

As there are only (too) very few venting holes on the downside of the device I assumed this could be the cause for the crash. It is not I proofed:

I opened the case (two screws on the bottom and four plastic clamps, two on very long side, sits very tight but can be removed without breaking the brackets if you work carful) and tried again with the case open:

Too put load on the device I copied a 3GB directory with mp3 files and startet iperf:

Device crashed after a few minutes, wlan does not come up again. Had to hard-reset (powercycle).

Active cooling:

Put a big office-fan right in front of the opened device:

Same result, device crashed after a few minutes but wlan came back by itself this time.

So the issue is NOT related to overheating but to some bug relatet to OpenWRT.

# iperf -c 192.168.200.14 -i 5 -t300
[  3] 215.0-220.0 sec  34.2 MBytes  57.5 Mbits/sec
[  3] 220.0-225.0 sec  34.2 MBytes  57.5 Mbits/sec
[  3] 225.0-230.0 sec  28.0 MBytes  46.9 Mbits/sec
[  3] 230.0-235.0 sec  1.12 MBytes  1.88 Mbits/sec
[  3] 235.0-240.0 sec  0.00 Bytes  0.00 bits/sec
[  3] 240.0-245.0 sec  0.00 Bytes  0.00 bits/sec
[  3] 245.0-250.0 sec  0.00 Bytes  0.00 bits/sec
07.07.20213919Base systemBug ReportVery LowLowTPLink RE450 wrong DTSTrunkUnconfirmed Task Description

Supply the following if possible:
- Device problem occurs on:
TPLink RE450 v2

- Software versions of OpenWrt/LEDE release, packages, etc.
openwrt snapshot 21.02

- Steps to reproduce
install basic firmware, check for available space, which is <500kB even if the firmware is 5MB and the device has 8MB flash.

Apparently wrong dts here: https://github.com/openwrt/openwrt/blob/master/target/linux/ath79/dts/qca9563_tplink_re450-v2.dts in particular:

partition@630000 {
	label = "config";
	reg = <0x630000 **0x020000**>;
	read-only;
};
art: partition@7f0000 {
	label = "art";
	reg = <0x7f0000 0x010000>;
	read-only;
};

should be changed to:

partition@630000 {
	label = "config";
	reg = <0x630000 **0x01c0000**>;
	read-only;
};
art: partition@7f0000 {
	label = "art";
	reg = <0x7f0000 0x010000>;
	read-only;
};
 


05.07.20213915Base systemBug ReportVery LowLowExpiration time for leases populated incorrectly in dhc...openwrt-21.02Unconfirmed Task Description
 
I’m running 21.02 on a FriendlyArm R4S. Noticed that all dhcp leases in Luci show as expired. Checking dhcp.leases, it shows:
43200 dc:xx:xx:xx:xx:xx 192.168.1.52 octopi *

According to dnsmasq, the first column should be the timestamp of when the lease is expiring (so either ‘now + leasetime’ or ‘uptime + leasetime’). In this case, it is just ‘0 + leasetime’.

Not sure if this is an issue with dnsmasq or openwrt itself. Happy to add more info if needed!


05.07.20213914Base systemBug ReportVery LowLowFailsafe button is inverted under TP-Link TL-WR842N/ND ...openwrt-19.07Unconfirmed Task Description

My 2 routers (TL-WR842v1, TL-WR842v2) were modded to have 64MB of RAM.
I also have TL-WR842v3 for reference.

This is great time to move from 17.01 to 19.07 (”refs/heads/openwrt-19.07” branch).
My build configuration is very simple: stock .config + Luci.
Config files are differ only on this line:

CONFIG_TARGET_ath79_generic_DEVICE_tplink_tl-wr842n-v1=y
CONFIG_TARGET_ath79_generic_DEVICE_tplink_tl-wr842n-v2=y
CONFIG_TARGET_ath79_generic_DEVICE_tplink_tl-wr842n-v3=y

Builds were made on ec76c365c1d60bf6a4f69b1ab3ce132f97f34dbb checkout (2021-06-14 - Koen Vandeputte - gitignore: add .ccache folder).

Boxes with hardware revisions v1 and v3 are working just fine.
But v2 almost always boots into failsafe mode :(
If I hold “wifi on/off” button v2 boots normal.
My wild guess: GPIO configuration is broken.

After ‘git bisect’ session I’ve found that following commit makes big difference:
2021-02-26 - Koen Vandeputte - kernel: bump 4.14 to 4.14.222 (b4a4d04b919b4a18a03e52a9e6bc18ddd924f554)
I’m not skilled enough to dig into kernel bisecting territory.

Before above commit router almost always boots normal.
After it router almost always boots into failsafe mode. But if I reboot it using reboot@SSH command it will boot just fine. So, power cycle ⇒ failsafe, reboot command ⇒ boots normal.

Looks like some sort of hardware initialization is made “too late” in boot process and querying GPIO state gives wrong readings.
That explains proper behavior after soft reboot.

04.07.20213913Base systemBug ReportVery LowMediumOn WAC124, the frrequency database is no read correctlyopenwrt-21.02Unconfirmed Task Description

Apologies for not reporting this sooner - it has been true for the last
several months of beta’s and for rc3.

When choosing a frequency for 5ghz for the Netgear WAC124:
[1] an incomplete list is given (nothing above channel 144)
[2] changing the width (20/40/80) does not affect choices
[3] NO choice will work except ch 36. Any other choice will be
accepted but the radio will be disabled - in GUI and in reality.
[4] Ch 36 does work fine

This has been true whether access the device from Mac/Linux or Windows,
Firefox or Chrome, so suspect base package issue (as opposed to GUI), but
not sure.

In case this helps any:
Netgear GUI allows any non-DFS channel (as appropriate for bw) up to 165
dd-wrt gui allows all (dfs/non-dfs) (as appropriate for bw) up to 165

Note that the WAC124 is limited to 100mw (great for AP, as often < $55).

I’ve 3 of them, so can test as desired.
I’ve saved the partitions (eg: factory) in case that is useful for anyone.


Showing tasks 201 - 250 of 1419 Page 5 of 29<<First - 3 - 4 - 5 - 6 - 7 - Last >>

Available keyboard shortcuts

Tasklist

Task Details

Task Editing