OpenWrt/LEDE Project

Welcome to the OpenWrt/LEDE Project bug reporting and issue tracking system

Problems to be reported here are for the OpenWrt/LEDE Project targets, sources, toolchain, core packages, build procedures, distribution and infrastructure. Guidelines for submitting a good bug report can be found at the OpenWrt/LEDE Project website. Problems related to LuCI or OpenWrt packages need to be reported in their repositories:

Notifications of all submissions and task changes are sent to lede-bugs@infradead.org.

OpenedIDCategory  ascTask TypePrioritySeveritySummaryReported InStatus
13.09.20181845Base systemBug ReportVery LowHighTL-WR840N v5 wifi troublesopenwrt-18.06Unconfirmed Task Description

Supply the following if possible:
- Device problem occurs on
TL-WR840N v5
access point config
wpa2 auto
DHCP off
- Software versions of OpenWrt/LEDE release, packages, etc.
18.06.1
snapshot
- Steps to reproduce

 

try connect more wifi clients over some hours and after this router is unusable over wifi
standart logs dont show any troubles

17.09.20181851Base systemBug ReportVery LowHighLoss of LAN<->WLAN connectivity on WR1043ND v4openwrt-18.06Unconfirmed Task Description

Hi
I am having repeatable issues with LuCI openwrt-18.06, observed on OpenWrt 18.06.1
The network connectivity between WAN and LAN is unstable, every couple of seconds the network stops responding. I can observe it as:
1. ping times: from 1ms to 10ms for devices in the same network as WAN interface
2. the remote desktop freezes and restarts
3. the network speed while copying files is very low (from 1MB/s to 5MB/s).

My configuration:
WAN - static IP
LAN - DHCP server
WLAN - Two WiFi networks.

I have removed all IPv6 system packets, disabled WLAN which did not make any difference, installed factory clean image and still this issue appears.
I am not seeing this issue when the TPLINK device works as the switch (WAN is not plugged, the network goes through LAN ports).
I am able to observe this issue at several devices.

19.09.20181855Base systemBug ReportVery LowHighUSB works ONLY with WiFi disabledopenwrt-18.06Unconfirmed Task Description

The problem occurs on Netgear WNDR3700v3 USING latest 18.06.

After setting up the router and installing required USB packages then rebooting the router, USB can’t be accessed. USB LED indicator light flickers few times during booting of the router, then shuts off. Using DMESG later I see that USB connects, then suddenly disconnects. The ONLY way to use USB functionality is to DISABLE WIFI.

To simply reproduce the issue, flash openwrt to your wndr3700v3, install required base USB packages.

1.) Disable wifi and find USB devices working normally.
2.) Enable Wifi and find USB devices not working and not being powered. (no led indicator on USB).

Use DMESG to see USB being recognized during boot and then simply later disconnected for no reason whatsoever.

The same issue did occur on 17.01. with the same behavior.

07.10.20181883Base systemBug ReportVery LowHighWAN interface VLAN not working on AVM FRITZ!Box 4040TrunkUnconfirmed Task Description

WAN interface of AVM FRITZ!Box 4040 is on eth1. To gain internet connectivity the ISP requires VLAN tagging with ID 7. But while I can send packets through interface eth1, I cannot through eth1.7.

Affected device: https://openwrt.org/toh/hwdata/avm/avm_fritz_box_4040 Affected versions: All I have tested, that is: 18.06.1 and the snapshot available today.

I haven’t seen any disturbing firewall rules and it still doesn’t work after flushing iptables completely.

Steps to reproduce:

- flash OpenWrt 18.06.1 to FRITZ!Box 4040
- change WAN ifname to eth1.7
- connect WAN port to laptop or monitoring device with Wireshark or similar
- send something via eth1.7, e.g. ping, but dhcp or pppd are sending stuff anyway

What happens:

Monitoring device does not see pings, dhcp, pppoe or other packets that go through eth1.7. It received when sending via eth1 directly (untagged). When sniffing via tcpdump on the router, it looks like the packets are send, but they are actually not going over the wire.

What should happen:

VLAN tagged packets are send properly (so PPPoE discovery succeeds in the end).

It was advised to open this bug report in the following forum thread. There is also some more information including configuration dumps. https://forum.openwrt.org/t/vlan-configuration-for-telekom/21841

13.10.20181893Base systemBug ReportVery LowHighRouting/NAT Offloading now working with VoIP/IPTV VLANsTrunkUnconfirmed Task Description

I’m using the latest build OpenWrt 18.06.1 r7258-5eb055306f / LuCI openwrt-18.06 branch (git-18.284.42397-55ebe88)

With ZBT-WG3526 (16M), MediaTek MT7621 ver:1 eco:3.

I’ve VLANs for VoIP and IPTV.

If I enable Routing/NAT Offloading (tried both options (software and hardware), it looks that this feature doesn’t allows the VoIP and IPTV traffic to work as it was doing previously.+

I know this is experimental and may be still needs some more testing, etc., but I just wanted to let the developers know about this issue, in case, they haven’t realized it.

29.10.20181917Base systemBug ReportVery LowHighMT7621 hw offloading crashingTrunkUnconfirmed Task Description

I’m using the latest build OpenWrt 18.06.1 r7258-5eb055306f / LuCI openwrt-18.06 branch (git-18.284.42397-55ebe88)

With ZBT-WG3526 (16M), MediaTek MT7621 ver:1 eco:3.

Using HW offloading makes systems unstable after less than 24 hours.

I’ve tested it during several days. Now using SW offloading seems to be working ok.

I’ve posted traces here:

https://forum.openwrt.org/t/mt7621-offloading-reboots/24043

01.11.20181922Base systemBug ReportVery LowHighBuilding on mac os 10.13.6 fails due to perl issues wit...TrunkUnconfirmed Task Description

Attempting to build latest OpenWrt firmware for NETGEAR R7800 (arm-openwrt-linux-musl) fails with Perl errors about dynamic module loading:

/Volumes/OpenWrt/NETGEAR_R7800/staging_dir/hostpkg/usr/bin/perl5.28.0 files/perlconfig.pl -Dowrt:target_cc='arm-openwrt-linux-muslgnueabi-gcc' -Dowrt:gccversion="7.3.0" -Dowrt:target_cross='arm-openwrt-linux-muslgnueabi-' -Dowrt:cflags='-O2 -pipe -mcpu=cortex-a9 -mfpu=vfp3 -fno-caller-saves -fno-plt -fhonour-copts -Wno-error=unused-but-set-variable -Wno-error=unused-result -mfloat-abi=hard -I/Volumes/OpenWrt/NETGEAR_R7800/staging_dir/target-arm_cortex-a15+neon-vfpv4_musl_eabi/usr/include -I/Volumes/OpenWrt/NETGEAR_R7800/staging_dir/target-arm_cortex-a15+neon-vfpv4_musl_eabi/include -I/Volumes/OpenWrt/NETGEAR_R7800/staging_dir/toolchain-arm_cortex-a15+neon-vfpv4_gcc-7.3.0_musl_eabi/usr/include -I/Volumes/OpenWrt/NETGEAR_R7800/staging_dir/toolchain-arm_cortex-a15+neon-vfpv4_gcc-7.3.0_musl_eabi/include/fortify -I/Volumes/OpenWrt/NETGEAR_R7800/staging_dir/toolchain-arm_cortex-a15+neon-vfpv4_gcc-7.3.0_musl_eabi/include' -Dowrt:ldflags='-L/Volumes/OpenWrt/NETGEAR_R7800/staging_dir/target-arm_cortex-a15+neon-vfpv4_musl_eabi/usr/lib -L/Volumes/OpenWrt/NETGEAR_R7800/staging_dir/target-arm_cortex-a15+neon-vfpv4_musl_eabi/lib -L/Volumes/OpenWrt/NETGEAR_R7800/staging_dir/toolchain-arm_cortex-a15+neon-vfpv4_gcc-7.3.0_musl_eabi/usr/lib -L/Volumes/OpenWrt/NETGEAR_R7800/staging_dir/toolchain-arm_cortex-a15+neon-vfpv4_gcc-7.3.0_musl_eabi/lib -znow -zrelro' -Dowrt:libc="musl" -Dowrt:ipv6=undef -Dowrt:threads=no -Dowrt:staging_dir='/Volumes/OpenWrt/NETGEAR_R7800/staging_dir/target-arm_cortex-a15+neon-vfpv4_musl_eabi' -Dowrt:host_perl_prefix='/Volumes/OpenWrt/NETGEAR_R7800/staging_dir/hostpkg/usr' files/version.config files/base.config files/arm.config files/architecture.config files/signal.config files/threads.config files/libc.config files/misc.config > /Volumes/OpenWrt/NETGEAR_R7800/build_dir/target-arm_cortex-a15+neon-vfpv4_musl_eabi/perl/perl-5.28.0/config.sh
Can't load module List::Util, dynamic loading not available in this perl.
  (You may need to build a new perl executable which either supports
  dynamic loading or has the List::Util module statically linked into it.)
 at files/perlconfig.pl line 229.
Compilation failed in require at files/perlconfig.pl line 229.
BEGIN failed--compilation aborted at files/perlconfig.pl line 229.
make[3]: *** [/Volumes/OpenWrt/NETGEAR_R7800/build_dir/target-arm_cortex-a15+neon-vfpv4_musl_eabi/perl/perl-5.28.0/.configured_68b329da9893e34099c7d8ad5cb9c940] Error 255
make[3]: Leaving directory `/Volumes/OpenWrt/NETGEAR_R7800/feeds/packages/lang/perl'
time: package/feeds/packages/perl/compile#0.25#0.13#0.66
make[2]: *** [package/feeds/packages/perl/compile] Error 2
make[2]: Leaving directory `/Volumes/OpenWrt/NETGEAR_R7800'
make[1]: *** [/Volumes/OpenWrt/NETGEAR_R7800/staging_dir/target-arm_cortex-a15+neon-vfpv4_musl_eabi/stamp/.package_compile] Error 2
make[1]: Leaving directory `/Volumes/OpenWrt/NETGEAR_R7800'
make: *** [world] Error 2
14.11.20181949Base systemBug ReportVery LowHighTL -1043ND V1 default gateway not foundopenwrt-18.06Unconfirmed Task Description

Supply the following if possible:
- Device problem occurs on
TP-LINK 1043ND version 1
- Software versions of OpenWrt/LEDE release, packages, etc.
18.06.1
- Steps to reproduce

 


15.11.20181952Base systemBug ReportVery LowHighwifi with hidden ssid and mac-filter doesn't work on IO...AllUnconfirmed Task Description

on tp-link_tl-wr842nd_v1 18.06 and 18.06.1

If hidden ssid and mac-filter is enabled, IOS 12 doesn't able to connect on this wifi network.

But if ssid broadcast is running with mac-filter enabled or ssid broadcast hidden and mac-filter disabled, then it works.

15.11.20181953Base systemBug ReportVery LowHighAsus RT N56U 5GHz radio doesn't work if 2.4GHz radio is...TrunkUnconfirmed Task Description

Version: 18.06.1
Asus RT N56U

When the 2.4GHz radio is enabled, the 5GHz radio does not function when both are set to US country code.

Steps to reproduce:
Set up radio 1 and radio 2 with US country codes.
Reboot.
Only the 2.4GHz radio will work.
If you disable the 2.4GHz and reboot, the 5GHz will work.

Any additional info you thinks is important:
Tried all workarounds listed.
More information about a bug in the original firmware fixed in Padavan’s firmware related to the 5GHz radio can be found here:
https://dev.archive.openwrt.org/ticket/17659.html#comment:23

Workaround:
Set the 2.4GHz radio country code to World (00) and reboot. Leave the 5GHz on US. Now both radios work.

24.12.20182024Base systemBug ReportVery LowHighsysupgrade silently does nothing in case of active swap...TrunkUnconfirmed Task Description

Trying sysupgrade on my ZBT WE1026, with SD-Card installed, and swap file active on it, silently does not succeed.

However, as I am using ‘sysupgrade -v -n -f /tmp/some_pars.tar.gz /tmp/fw.bin’ the files from some_pars.tar.gz are applied to unmodified system, resulting in inconsistencies.

Doing swapoff before
sysupgrade fixed my problem.

sysupgrade should at least issue an error message, when it does not succeed.
As I suspect, that unsuccessful umount of my block device with swap-file open is the culprit.


07.01.20192051Base systemBug ReportVery LowHighDHCP not working properly. openwrt-18.06Unconfirmed Task Description

I have WRT3200ACM and also EX6150v2 both using openwrt 18.06.01. With their stock firmware, my IOT devices like Mi LED and Wemo will connect just fine. With OpenWrt, some devices just not getting IP from the router/AP. Also, relayd is not working when the main router is using OpenWrt. If I use stock firmware as main AP then all problem solved. Seems like something wrong with OpenWrt’s DHCP system. I have also tried 18.06 version.

15.01.20192059Base systemBug ReportVery LowHighuclient-fetch not working at all on http (not https) co...TrunkUnconfirmed Task Description

I just tried today’s trunk snapshot on my Turris Omnia; everything’s working fine apart from uclient-fetch. I noticed the failure because the ddns updater stopped working. If I install wget, everything works, since wget replaces uclient-fetch. Sample output follows.

Bad:

root@heimdall:/tmp# uclient-fetch http://perdu.com/ Downloading ‘http://perdu.com/’ Failed to establish connection
root@heimdall:/tmp#

Good:

root@heimdall:/tmp# wget http://perdu.com/ –2019-01-15 14:31:09– http://perdu.com/ Resolving perdu.com... 208.97.177.124
Connecting to perdu.com|208.97.177.124|:80... connected.
HTTP request sent, awaiting response... 200 OK
Length: 204 [text/html]
Saving to: ‘index.html’

index.html 100%[==================================================================================================================================================================>] 204 --.-KB/s in 0s 2019-01-15 14:31:10 (16.4 MB/s) - 'index.html' saved [204/204] root@heimdall:/tmp# Image builder command line: make image PROFILE=turris-omnia PACKAGES="-kmod-ath9k -dnsmasq -odhcpd -odhcpd-ipv6only -odhcp6c -ppp -ppp-mod-pppoe ddns-scripts dnsmasq-full ethtool haveged htop ipset kmod-ipt-raw kmod-ipt-raw6 kmod-nf-nathelper-extra kmod-wireguard nano sqm-scripts tcpdump tor wget wireguard-tools zram-swap"

18.01.20192062Base systemBug ReportVery LowHighMTU is not set to 1508/1500 when using PPPoEopenwrt-18.06Unconfirmed Task Description

TP-LINK Archer C7, OpenWrt 18.06.1 r7258-5eb055306f / LuCI openwrt-18.06 branch (git-18.228.31946-f64b152).

Use PPPoE for WAN. Set MTU to 1508.

Observe ifconfig result. MTU is set at 1492, it should be 1500.

Add

config interface ‘eth0’

option ifname 'eth0'
option mtu '1508'

to /etc/config/network, ensure PPPoE MTU (as above) is set to 1508 and restart the network/reboot the router.

Observe ifconfig result. MTU is set at 1500 as expected.

23.01.20192081Base systemBug ReportVery LowHighSnapShot Install for TP-Link Archer C20 AC750 Hardly Wo...openwrt-18.06Unconfirmed Task Description

Dear Colleagues:

1) I have been testing basic networking functions of OpenWrt 18.06.1 “full Install” version on the above captioned device since 2018-10-16. This was done through BIN file download and install process. The operations tested appeared to be fine.

2) I was instructed to try a “snapshot Install” version to see if a recent Kernel update (2018-12-14, see link below.) is performing as intended. Upon powering on this version in the existing test-bed, however, the DHCP client PCs (with Xubuntu OS) appeared to see the LAN service by having their addresses assigned and were able to get response from the gateway when PINGing it with 192.168.1.1. However, attempting to use a web browser to access the router homepage at 192.168.1.1 failed. Also, the PCs could not get PINGing response from one another. Perhaps the earliest tell-tail sign is that as soon as the router is powered on with the “snapshot version”, the 2.4G WiFi status indicator LED is turned on, while the “full Install” version does not.

3) To verify, I downloaded and installed both full and snapshot versions of current BIN files from the OpenWrt website today and verified their integrity by checking the check-sums first. The above symptoms appeared to be repeatable after going through the processes a couple cycles alternating between the two versions.

Thanks for your attention,

Abe (2019-01-23 15:58)


05.02.20192101Base systemBug ReportVery LowHighWDS bridge and PPPoE MTU problemAllUnconfirmed Task Description

Device: Netgear R7800
This issue is not present with original Netgear firmware and is not present with LEDE 17 (older kernel).

Preface:
I have very strange issue with interfaces MTU and it looks to be introduced with newer kernel (4.14).

My network is attached as a png:
1. my ISP uses VDSL, i just have a PPPoE (MTU=1492) on the ethernet interface through the ISP modem
2. all other internal clients and routers interfaces have MTU=1500

Ping from R7800 to 1.1.1.1 with 2000 packet size and fragmentation allowed = success
Ping from ArcherC7v2 to R7800 with 2000 packet size and fragmentation allowed = success
Ping from PC1 to R7800 with 2000 packet size and fragmentation allowed = success
Ping from PC2 to R7800 with 2000 packet size and fragmentation allowed = success
Ping from PC1 to 1.1.1.1 with 2000 packet size and fragmentation allowed = failure
Ping from PC2 to 1.1.1.1 with 2000 packet size and fragmentation allowed = success

Now the fun part:
Ping from PC1 to 1.1.1.1 with 1473 packet size and fragmentation allowed = failure
Ping from PC1 to 1.1.1.1 with 1472 packet size (1492-20) and fragmentation allowed = success

It seems a WDS (4addr) problem combined with PPPoE being at MTU=1492 at this point, but:
Ping from ArcherC7v2 to 1.1.1.1 with 2000 packet size and fragmentation allowed = success

I’ve messed up with MTU on all the interfaces, the only thing that fix the issue is setting the br-lan interface of the R7800 to MTU=1491, as soon as the bridge has MTU>1491 the pings fail.

R7800 network config

config switch
        option name 'switch0'
        option reset '1'
        option enable_vlan '1'

config switch_vlan
        option device 'switch0'
        option vlan '1'
        option ports '1 2 3 4 6t'

config switch_vlan
        option device 'switch0'
        option vlan '2'
        option ports '5 0t'

config interface 'lan'
        option type 'bridge'
        option proto 'static'
        option ipaddr '192.168.1.1'
        option netmask '255.255.255.0'
        option ip6assign '60'
        option stp '1'
        option mtu '1500'
        option ifname 'eth1.1'

config interface 'TIM_FTTC'
        option proto 'pppoe'
        option ifname 'eth0.2'
        option username '***'
        option password '***'
        option ipv6 'auto'
        option metric '1'
        option peerdns '0'
        option keepalive '5 6'

R7800 wireless config

config wifi-device 'radio0'
        option type 'mac80211'
        option hwmode '11a'
        option path 'soc/1b500000.pci/pci0000:00/0000:00:00.0/0000:01:00.0'
        option htmode 'VHT80'
        option channel '136'
        option txpower '23'
        option country 'US'
        option legacy_rates '0'
        option noscan '1'

config wifi-iface 'default_radio0'
        option device 'radio0'
        option mode 'ap'
        option ssid '***'
        option encryption 'psk2+ccmp'
        option key '***'
        option wps_pushbutton '0'
        option network 'lan'
        option wds '1'

ArcherC7v2 network config

config switch
        option name 'switch0'
        option reset '1'
        option enable_vlan '1'

config switch_vlan
        option device 'switch0'
        option vlan '1'
        option ports '1 2 3 4 6t'

config switch_vlan
        option device 'switch0'
        option vlan '2'
        option ports '5 0t'

config interface 'lan'
        option type 'bridge'
        option proto 'static'
        option ipaddr '192.168.1.2'
        option netmask '255.255.255.0'
        option stp '1'
        option mtu '1500'
        option ifname 'eth1.1'

ArcherC7v2 wireless config

config wifi-device 'radio0'
        option type 'mac80211'
        option channel '36'
        option hwmode '11a'
        option path 'pci0000:01/0000:01:00.0'
        option htmode 'VHT80'
        option txpower '23'
        option country 'US'
        option legacy_rates '0'
        option noscan '1'

config wifi-iface 'default_radio0'
        option device 'radio0'
        option mode 'sta'
        option wds '1'
        option ssid '***'
        option encryption 'psk2+ccmp'
        option key '***'
        option wps_pushbutton '0'
        option network 'lan'

WAN zone on firewall on R7800 has

option mtu_fix '1'
10.02.20192114Base systemBug ReportVery LowHighWG302v1 (ixp4xx-generic) LAN (eth0) start and then stop...openwrt-18.06Unconfirmed Task Description

Hello

Device: Netgear WG302v1 ixp4xx
FW: 18.06.1 & 18.06.2

Device problem occurs at boot.
During boot LAN (eth0) become ready (LEDs are lit) and then stop after ~2 or ~3 seconds (LEDs are off).
WAN (radio) interface seems working but Ethernet (eth0) is down.
Impossible to get it up because ifconfig up have no effect.

No packages are installed only stock zImage and Shashfs.

With 18.06.1 (default config, IP after flashing) :
OpenWRT say that ethO is up and ready but eth0 and LEDs are off.
Impossible to reach LuCi or ping a computer with IP 192.168.1.10 (connected through serial console on device)
At boot eth0 stay up sometimes ~ 1 of 20.

With 18.06.2 (default config, IP after flashing) :
It seems there are more information during boot.
Kernel is reporting that br-lan: port 1(eth0) entered disabled stat
ifconfig up/down has no effect.

Step to reproduce:
Flash & boot.

You can find included as attached file 18.06.1 & 18.06.2 dmesg boot log.

Kind Regards

23.02.20192141Base systemBug ReportVery LowHighOn router Linksys EA6350v3, Luci shows missing port on ...TrunkUnconfirmed Task Description

Hi!

I am using OpenWRT development from Feb21 on my Linksys EA6350v3 router. So far, everything works fine, however I am trying to setup the WAN port with a VLAN, but if I access: Luci → Network → Switch it only displays the CPU port and the 4 LAN ports, the WAN port is not displayed, but if I access the router via SSH, then the port is there on swconfig:

root@wl:~# swconfig dev switch0 show
Global attributes:

enable_vlan: 1
enable_mirror_rx: 0
enable_mirror_tx: 0
mirror_monitor_port: 0
mirror_source_port: 0
linkdown: ???

Port 0:

mib: Port 0 MIB counters

RxBroad : 722
RxPause : 0
RxMulti : 2898
RxFcsErr : 0
RxAlignErr : 0
RxRunt : 0
RxFragment : 0
Rx64Byte : 34565
Rx128Byte : 717134
Rx256Byte : 12692
Rx512Byte : 7510
Rx1024Byte : 7809
Rx1518Byte : 141976
RxMaxByte : 193165
RxTooLong : 0
RxGoodByte : 573563874
RxBadByte : 0
RxOverFlow : 0
Filtered : 4
TxBroad : 3813
TxPause : 0
TxMulti : 73600
TxUnderRun : 0
Tx64Byte : 62619
Tx128Byte : 115302
Tx256Byte : 15655
Tx512Byte : 41091
Tx1024Byte : 34454
Tx1518Byte : 2869708
TxMaxByte : 0
TxOverSize : 0
TxByte : 4378564661
TxCollision : 0
TxAbortCol : 0
TxMultiCol : 0
TxSingleCol : 0
TxExcDefer : 0
TxDefer : 0
TxLateCol : 0

pvid: 1
link: port:0 link:up speed:1000baseT full-duplex txflow rxflow 

Port 1:

mib: Port 1 MIB counters

RxBroad : 10
RxPause : 0
RxMulti : 126
RxFcsErr : 0
RxAlignErr : 0
RxRunt : 0
RxFragment : 0
Rx64Byte : 40
Rx128Byte : 534
Rx256Byte : 313
Rx512Byte : 38
Rx1024Byte : 18
Rx1518Byte : 15
RxMaxByte : 0
RxTooLong : 0
RxGoodByte : 141761
RxBadByte : 0
RxOverFlow : 0
Filtered : 13
TxBroad : 180
TxPause : 0
TxMulti : 367
TxUnderRun : 0
Tx64Byte : 335
Tx128Byte : 362
Tx256Byte : 279
Tx512Byte : 216
Tx1024Byte : 29
Tx1518Byte : 52
TxMaxByte : 0
TxOverSize : 0
TxByte : 274900
TxCollision : 0
TxAbortCol : 0
TxMultiCol : 0
TxSingleCol : 0
TxExcDefer : 0
TxDefer : 0
TxLateCol : 0

pvid: 1
link: port:1 link:down

Port 2:

mib: Port 2 MIB counters

RxBroad : 0
RxPause : 0
RxMulti : 0
RxFcsErr : 0
RxAlignErr : 0
RxRunt : 0
RxFragment : 0
Rx64Byte : 0
Rx128Byte : 0
Rx256Byte : 0
Rx512Byte : 0
Rx1024Byte : 0
Rx1518Byte : 0
RxMaxByte : 0
RxTooLong : 0
RxGoodByte : 0
RxBadByte : 0
RxOverFlow : 0
Filtered : 0
TxBroad : 4419
TxPause : 0
TxMulti : 76469
TxUnderRun : 0
Tx64Byte : 46240
Tx128Byte : 1084
Tx256Byte : 2641
Tx512Byte : 28047
Tx1024Byte : 2915
Tx1518Byte : 1
TxMaxByte : 0
TxOverSize : 0
TxByte : 18438433
TxCollision : 0
TxAbortCol : 0
TxMultiCol : 0
TxSingleCol : 0
TxExcDefer : 0
TxDefer : 0
TxLateCol : 0

pvid: 1
link: port:2 link:up speed:100baseT full-duplex txflow rxflow auto

Port 3:

mib: Port 3 MIB counters

RxBroad : 0
RxPause : 0
RxMulti : 0
RxFcsErr : 0
RxAlignErr : 0
RxRunt : 0
RxFragment : 0
Rx64Byte : 0
Rx128Byte : 0
Rx256Byte : 0
Rx512Byte : 0
Rx1024Byte : 0
Rx1518Byte : 0
RxMaxByte : 0
RxTooLong : 0
RxGoodByte : 0
RxBadByte : 0
RxOverFlow : 0
Filtered : 0
TxBroad : 4419
TxPause : 0
TxMulti : 76469
TxUnderRun : 0
Tx64Byte : 46240
Tx128Byte : 1084
Tx256Byte : 2641
Tx512Byte : 28047
Tx1024Byte : 2915
Tx1518Byte : 1
TxMaxByte : 0
TxOverSize : 0
TxByte : 18438433
TxCollision : 0
TxAbortCol : 0
TxMultiCol : 0
TxSingleCol : 0
TxExcDefer : 0
TxDefer : 0
TxLateCol : 0

pvid: 1
link: port:3 link:up speed:1000baseT full-duplex auto

Port 4:

mib: Port 4 MIB counters

RxBroad : 3765
RxPause : 0
RxMulti : 73151
RxFcsErr : 0
RxAlignErr : 0
RxRunt : 0
RxFragment : 0
Rx64Byte : 62113
Rx128Byte : 115122
Rx256Byte : 15386
Rx512Byte : 40931
Rx1024Byte : 34440
Rx1518Byte : 2869706
RxMaxByte : 0
RxTooLong : 0
RxGoodByte : 4378395323
RxBadByte : 0
RxOverFlow : 0
Filtered : 11
TxBroad : 379
TxPause : 0
TxMulti : 2755
TxUnderRun : 0
Tx64Byte : 34306
Tx128Byte : 717333
Tx256Byte : 12274
Tx512Byte : 7258
Tx1024Byte : 7735
Tx1518Byte : 335099
TxMaxByte : 0
TxOverSize : 0
TxByte : 569081244
TxCollision : 0
TxAbortCol : 0
TxMultiCol : 0
TxSingleCol : 0
TxExcDefer : 0
TxDefer : 0
TxLateCol : 0

pvid: 1
link: port:4 link:up speed:1000baseT full-duplex txflow rxflow auto

Port 5:

mib: Port 5 MIB counters

RxBroad : 38
RxPause : 0
RxMulti : 323
RxFcsErr : 0
RxAlignErr : 0
RxRunt : 0
RxFragment : 0
Rx64Byte : 526
Rx128Byte : 312
Rx256Byte : 54
Rx512Byte : 205
Rx1024Byte : 23
Rx1518Byte : 30
RxMaxByte : 0
RxTooLong : 0
RxGoodByte : 217499
RxBadByte : 0
RxOverFlow : 0
Filtered : 9
TxBroad : 348
TxPause : 0
TxMulti : 259
TxUnderRun : 0
Tx64Byte : 344
Tx128Byte : 406
Tx256Byte : 200
Tx512Byte : 199
Tx1024Byte : 20
Tx1518Byte : 13
TxMaxByte : 0
TxOverSize : 0
TxByte : 194389
TxCollision : 0
TxAbortCol : 0
TxMultiCol : 0
TxSingleCol : 0
TxExcDefer : 0
TxDefer : 0
TxLateCol : 0

pvid: 1
link: port:5 link:down

VLAN 1:

vid: 1
ports: 0 1 2 3 4 5 

VLAN 2:

vid: 2
ports: 0t 5t 

root@wl:~#

So the firmware knows there is an additional port in the switch, it’s just Luci that does not display it.

For extra info, here’s the OpenWRT version I am running:

BusyBox v1.30.1 () built-in shell (ash)

_______                     ________        __

| |.—–.—–.—–.| | | |.—-.| |_
| - || _ | -| || | | || _|| _|
|
_|| |_||||||| ||

        |__| W I R E L E S S   F R E E D O M

—————————————————– OpenWrt SNAPSHOT, r9414-2d13945


Thanks in advance for your help with this, very appreciated.


05.03.20192162Base systemBug ReportVery LowHighLinksys 3200ACM stop to function, no connection out of ...openwrt-18.06Unconfirmed Task Description

Supply the following if possible:
- Device problem occurs on Linksys WRT 3200ACM
- Software versions of OpenWrt/LEDE release, packages, etc.
OpenWrt 18.06.2 r7676-cddd7b4c77 / LuCI openwrt-18.06 branch (git-19.020.41695-6f6641d)
+ IGMProxy (followed this tuturial https://oldwiki.archive.openwrt.org/doc/howto/udp_multicast)
- Steps to reproduce

 I have a large network with arround 200 Virtual Machines connected to the router, this router is great and looks like it can handle all of my VMs easly (my ISP router break after 80VMs) but out of nowhere sometimes the router stop to function, I cannot connect to it from LAN or WLAN. I am not sure if this is related with the VMs or if it is another issue

I had remote logs active, and the last time this ocurred I got this from the logs:
root# nc -u -4 -l 5555

<30>Mar  5 00:38:13 OpenWrt logread[6094]: Logread connected to 10.0.10.1:5555
<28>Mar  5 00:38:26 OpenWrt odhcpd[1791]: DHCPV6 RENEW IA_NA from 00020000ab1119a3c79428a626de on br-lan: no binding
<29>Mar  5 00:41:05 OpenWrt netifd: wan (2068): udhcpc: sending renew to 10.141.0.1
<29>Mar  5 00:41:05 OpenWrt netifd: wan (2068): udhcpc: lease of 188.250.74.185 obtained, lease time 3600
<13>Mar  5 00:42:40 OpenWrt root: testLog “Blah1”
<28>Mar  5 00:43:43 OpenWrt odhcpd[1791]: DHCPV6 RENEW IA_NA from 00020000ab114ef36bcb13e12a6c on br-lan: no binding
<28>Mar  5 00:43:46 OpenWrt odhcpd[1791]: DHCPV6 RENEW IA_NA from 00020000ab11ec7b577aa4a2257e on br-lan: no binding
<28>Mar  5 00:47:21 OpenWrt odhcpd[1791]: DHCPV6 RENEW IA_NA from 00020000ab11ee5cdb55e31e9275 on br-lan: no binding
<28>Mar  5 00:48:45 OpenWrt odhcpd[1791]: DHCPV6 RENEW IA_NA from 00020000ab1119a3c79428a626de on br-lan: no binding
<30>Mar  5 00:49:14 OpenWrt dnsmasq-dhcp[2944]: DHCPREQUEST(br-lan) 10.0.0.202 00:50:56:96:e6:32
<30>Mar  5 00:49:14 OpenWrt dnsmasq-dhcp[2944]: DHCPACK(br-lan) 10.0.0.202 00:50:56:96:e6:32 zen
<28>Mar  5 00:53:21 OpenWrt odhcpd[1791]: DHCPV6 RENEW IA_NA from 00020000ab114ef36bcb13e12a6c on br-lan: no binding
<28>Mar  5 00:53:26 OpenWrt odhcpd[1791]: DHCPV6 RENEW IA_NA from 00020000ab11ec7b577aa4a2257e on br-lan: no binding
<28>Mar  5 00:58:16 OpenWrt odhcpd[1791]: DHCPV6 RENEW IA_NA from 00020000ab11ee5cdb55e31e9275 on br-lan: no binding

Right after I reset the router power I did an logread and could get this:

Tue Mar  5 00:42:43 2019 user.info kernel: [    3.202957] kmodloader: loading kernel modules from /etc/modules-boot.d/*
Tue Mar  5 00:42:43 2019 user.info kernel: [    3.234044] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
Tue Mar  5 00:42:43 2019 user.info kernel: [    3.243296] init: - preinit -
Tue Mar  5 00:42:43 2019 kern.info kernel: [    3.395512] mvneta f1070000.ethernet tmp0: renamed from eth0
Tue Mar  5 00:42:43 2019 kern.notice kernel: [    3.401750] random: procd: uninitialized urandom read (4 bytes read)
Tue Mar  5 00:42:43 2019 kern.info kernel: [    3.441356] mvneta f1034000.ethernet eth0: renamed from eth1
Tue Mar  5 00:42:43 2019 kern.info kernel: [    3.481320] mvneta f1070000.ethernet eth1: renamed from tmp0
Tue Mar  5 00:42:43 2019 kern.notice kernel: [    3.699138] random: jshn: uninitialized urandom read (4 bytes read)
Tue Mar  5 00:42:43 2019 kern.notice kernel: [    3.730488] random: jshn: uninitialized urandom read (4 bytes read)
Tue Mar  5 00:42:43 2019 kern.info kernel: [    3.892827] mvneta f1034000.ethernet eth0: configuring for fixed/sgmii link mode
Tue Mar  5 00:42:43 2019 kern.info kernel: [    3.900629] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Tue Mar  5 00:42:43 2019 kern.info kernel: [    3.906643] mvneta f1034000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
Tue Mar  5 00:42:43 2019 kern.info kernel: [    3.914852] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Tue Mar  5 00:42:43 2019 kern.notice kernel: [    6.969318] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 821
Tue Mar  5 00:42:43 2019 kern.notice kernel: [    6.989686] UBIFS (ubi0:1): recovery needed
Tue Mar  5 00:42:43 2019 kern.notice kernel: [    7.049827] UBIFS (ubi0:1): recovery completed
Tue Mar  5 00:42:43 2019 kern.notice kernel: [    7.054334] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
Tue Mar  5 00:42:43 2019 kern.notice kernel: [    7.062207] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
Tue Mar  5 00:42:43 2019 kern.notice kernel: [    7.072173] UBIFS (ubi0:1): FS size: 65138688 bytes (62 MiB, 513 LEBs), journal size 3301376 bytes (3 MiB, 26 LEBs)
Tue Mar  5 00:42:43 2019 kern.notice kernel: [    7.082681] UBIFS (ubi0:1): reserved for root: 3076660 bytes (3004 KiB)
Tue Mar  5 00:42:43 2019 kern.notice kernel: [    7.089325] UBIFS (ubi0:1): media format: w4/r0 (latest is w5/r0), UUID 0A2948E0-EE94-4D03-A2AA-5BDE63AE5BFC, small LPT model
Tue Mar  5 00:42:43 2019 user.info kernel: [    7.102478] mount_root: switching to ubifs overlay
Tue Mar  5 00:42:43 2019 kern.notice kernel: [    7.148010] ubi1: attaching mtd9
Tue Mar  5 00:42:43 2019 kern.notice kernel: [    7.236995] random: crng init done
Tue Mar  5 00:42:43 2019 kern.notice kernel: [    7.240412] random: 3 urandom warning(s) missed due to ratelimiting
Tue Mar  5 00:42:43 2019 kern.notice kernel: [    7.380723] ubi1: scanning is finished
Tue Mar  5 00:42:43 2019 kern.notice kernel: [    7.388751] ubi1: attached mtd9 (name "syscfg", size 86 MiB)
Tue Mar  5 00:42:43 2019 kern.notice kernel: [    7.394452] ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
Tue Mar  5 00:42:43 2019 kern.notice kernel: [    7.401361] ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
Tue Mar  5 00:42:43 2019 kern.notice kernel: [    7.408179] ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
Tue Mar  5 00:42:43 2019 kern.notice kernel: [    7.415174] ubi1: good PEBs: 680, bad PEBs: 8, corrupted PEBs: 0
Tue Mar  5 00:42:43 2019 kern.notice kernel: [    7.421208] ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
Tue Mar  5 00:42:43 2019 kern.notice kernel: [    7.428462] ubi1: max/mean erase counter: 8/4, WL threshold: 4096, image sequence number: 876597111
Tue Mar  5 00:42:43 2019 kern.notice kernel: [    7.437550] ubi1: available PEBs: 0, total reserved PEBs: 680, PEBs reserved for bad PEB handling: 32
Tue Mar  5 00:42:43 2019 kern.notice kernel: [    7.446817] ubi1: background thread "ubi_bgt1d" started, PID 829
Tue Mar  5 00:42:43 2019 kern.notice kernel: [    7.457387] UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 835
Tue Mar  5 00:42:43 2019 kern.notice kernel: [    7.477892] UBIFS (ubi1:0): recovery needed
Tue Mar  5 00:42:43 2019 kern.notice kernel: [    7.535464] UBIFS (ubi1:0): recovery completed
Tue Mar  5 00:42:43 2019 kern.notice kernel: [    7.539966] UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "syscfg"
Tue Mar  5 00:42:43 2019 kern.notice kernel: [    7.547410] UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
Tue Mar  5 00:42:43 2019 kern.notice kernel: [    7.557398] UBIFS (ubi1:0): FS size: 80375808 bytes (76 MiB, 633 LEBs), journal size 4063232 bytes (3 MiB, 32 LEBs)
Tue Mar  5 00:42:43 2019 kern.notice kernel: [    7.567882] UBIFS (ubi1:0): reserved for root: 3796347 bytes (3707 KiB)
Tue Mar  5 00:42:43 2019 kern.notice kernel: [    7.574529] UBIFS (ubi1:0): media format: w4/r0 (latest is w5/r0), UUID 61E88146-E8C2-4229-B3CE-3F574E1AD339, small LPT model
Tue Mar  5 00:42:43 2019 user.warn kernel: [    7.587144] urandom-seed: Seeding with /etc/urandom.seed
Tue Mar  5 00:42:43 2019 kern.info kernel: [    7.620917] mvneta f1034000.ethernet eth0: Link is Down
Tue Mar  5 00:42:43 2019 user.info kernel: [    7.692743] procd: - early -
Tue Mar  5 00:42:43 2019 user.info kernel: [    7.695657] procd: - watchdog -
Tue Mar  5 00:42:43 2019 user.info kernel: [    8.294006] procd: - watchdog -
Tue Mar  5 00:42:43 2019 user.info kernel: [    8.297241] procd: - ubus -
Tue Mar  5 00:42:43 2019 user.info kernel: [    8.350566] procd: - init -
Tue Mar  5 00:42:43 2019 user.info kernel: [    8.457200] kmodloader: loading kernel modules from /etc/modules.d/*
Tue Mar  5 00:42:43 2019 kern.info kernel: [    8.465564] ip6_tables: (C) 2000-2006 Netfilter Core Team
Tue Mar  5 00:42:43 2019 kern.info kernel: [    8.472404] Loading modules backported from Linux version wt-2017-11-01-0-gfe248fc2c180
Tue Mar  5 00:42:43 2019 kern.info kernel: [    8.480456] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d
Tue Mar  5 00:42:43 2019 kern.info kernel: [    8.493859] <<Marvell Mac80211 Wireless PCIE Network Driver version 10.3.8.0-20181114>>
Tue Mar  5 00:42:43 2019 kern.info kernel: [    8.501934] pci 0000:00:01.0: enabling device (0140 -> 0142)
Tue Mar  5 00:42:43 2019 kern.debug kernel: [    8.507713] ieee80211 phy0: priv->pcmd_buf = de040000  priv->pphys_cmd_buf = 1e040000
Tue Mar  5 00:42:43 2019 kern.debug kernel: [    8.560127] ieee80211 phy0: fw download start
Tue Mar  5 00:42:43 2019 kern.debug kernel: [    8.560132] ieee80211 phy0: ddr init: download start
Tue Mar  5 00:42:43 2019 kern.debug kernel: [    8.560509] ieee80211 phy0: ddr init: download complete
Tue Mar  5 00:42:43 2019 kern.debug kernel: [    8.698421] ieee80211 phy0: FwSize = 450732 downloaded Size = 450732 curr_iteration 65521
Tue Mar  5 00:42:43 2019 kern.debug kernel: [   11.560105] ieee80211 phy0: fw download complete
Tue Mar  5 00:42:43 2019 kern.info kernel: [   11.560137] ieee80211 phy0: device node: /soc/pcie/pcie@1,0
Tue Mar  5 00:42:43 2019 kern.debug kernel: [   11.575295] ieee80211 phy0: pcmd = de040000
Tue Mar  5 00:42:43 2019 kern.info kernel: [   11.593337] ieee80211 phy0: firmware version: 0x9030206
Tue Mar  5 00:42:43 2019 kern.info kernel: [   11.900106] ieee80211 phy0: firmware region code: 30
Tue Mar  5 00:42:43 2019 kern.info kernel: [   11.938916] ieee80211 phy0: 2G disabled, 5G enabled
Tue Mar  5 00:42:43 2019 kern.info kernel: [   11.943846] ieee80211 phy0: 4 TX antennas, 4 RX antennas
Tue Mar  5 00:42:43 2019 kern.info kernel: [   11.949442] pci 0000:00:02.0: enabling device (0140 -> 0142)
Tue Mar  5 00:42:43 2019 kern.debug kernel: [   11.955288] ieee80211 phy1: priv->pcmd_buf = d98c0000  priv->pphys_cmd_buf = 198c0000
Tue Mar  5 00:42:43 2019 kern.debug kernel: [   11.963534] ieee80211 phy1: fw download start
Tue Mar  5 00:42:43 2019 kern.debug kernel: [   11.963540] ieee80211 phy1: ddr init: download start
Tue Mar  5 00:42:43 2019 kern.debug kernel: [   11.963922] ieee80211 phy1: ddr init: download complete
Tue Mar  5 00:42:43 2019 kern.debug kernel: [   12.105401] ieee80211 phy1: FwSize = 450732 downloaded Size = 450732 curr_iteration 65527
Tue Mar  5 00:42:43 2019 kern.debug kernel: [   13.296113] ieee80211 phy1: fw download complete
Tue Mar  5 00:42:43 2019 kern.info kernel: [   13.296154] ieee80211 phy1: device node: /soc/pcie/pcie@2,0
Tue Mar  5 00:42:43 2019 kern.debug kernel: [   13.311376] ieee80211 phy1: pcmd = d98c0000
Tue Mar  5 00:42:43 2019 kern.info kernel: [   13.329129] ieee80211 phy1: firmware version: 0x9030206
Tue Mar  5 00:42:43 2019 kern.info kernel: [   13.636119] ieee80211 phy1: firmware region code: 30
Tue Mar  5 00:42:43 2019 kern.info kernel: [   13.668957] ieee80211 phy1: 2G enabled, 5G disabled
Tue Mar  5 00:42:43 2019 kern.info kernel: [   13.673887] ieee80211 phy1: 4 TX antennas, 4 RX antennas
Tue Mar  5 00:42:43 2019 kern.info kernel: [   13.681691] hidraw: raw HID events driver (C) Jiri Kosina
Tue Mar  5 00:42:43 2019 kern.info kernel: [   13.690270] Bluetooth: Core ver 2.22
Tue Mar  5 00:42:43 2019 kern.info kernel: [   13.693906] NET: Registered protocol family 31
Tue Mar  5 00:42:43 2019 kern.info kernel: [   13.698374] Bluetooth: HCI device and connection manager initialized
Tue Mar  5 00:42:43 2019 kern.info kernel: [   13.704792] Bluetooth: HCI socket layer initialized
Tue Mar  5 00:42:43 2019 kern.info kernel: [   13.709700] Bluetooth: L2CAP socket layer initialized
Tue Mar  5 00:42:43 2019 kern.info kernel: [   13.714807] Bluetooth: SCO socket layer initialized
Tue Mar  5 00:42:43 2019 kern.info kernel: [   13.720159] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
Tue Mar  5 00:42:43 2019 kern.info kernel: [   13.725501] Bluetooth: BNEP filters: protocol multicast
Tue Mar  5 00:42:43 2019 kern.info kernel: [   13.730788] Bluetooth: BNEP socket layer initialized
Tue Mar  5 00:42:43 2019 kern.info kernel: [   13.736995] Bluetooth: vendor=0x2df, device=0x9136, class=255, fn=2
Tue Mar  5 00:42:43 2019 kern.info kernel: [   14.523809] Bluetooth: FW download over, size 695532 bytes
Tue Mar  5 00:42:43 2019 kern.err kernel: [   15.120137] sdio platform data not available
Tue Mar  5 00:42:43 2019 kern.info kernel: [   15.120809] usbcore: registered new interface driver btusb
Tue Mar  5 00:42:43 2019 kern.info kernel: [   15.131483] Bluetooth: HCI UART driver ver 2.3
Tue Mar  5 00:42:43 2019 kern.info kernel: [   15.135948] Bluetooth: HCI UART protocol H4 registered
Tue Mar  5 00:42:43 2019 kern.info kernel: [   15.141118] Bluetooth: HCI UART protocol BCSP registered
Tue Mar  5 00:42:43 2019 kern.info kernel: [   15.146452] Bluetooth: HCI UART protocol ATH3K registered
Tue Mar  5 00:42:43 2019 kern.info kernel: [   15.152373] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
Tue Mar  5 00:42:43 2019 kern.info kernel: [   15.158323] Bluetooth: HIDP socket layer initialized
Tue Mar  5 00:42:43 2019 kern.info kernel: [   15.163866] ip_tables: (C) 2000-2006 Netfilter Core Team
Tue Mar  5 00:42:43 2019 kern.info kernel: [   15.174072] nf_conntrack version 0.5.0 (8192 buckets, 32768 max)
Tue Mar  5 00:42:43 2019 kern.info kernel: [   15.181224] mwifiex_sdio mmc0:0001:1: WLAN FW already running! Skip FW dnld
Tue Mar  5 00:42:43 2019 kern.info kernel: [   15.188222] mwifiex_sdio mmc0:0001:1: WLAN FW is active
Tue Mar  5 00:42:43 2019 kern.info kernel: [   15.197355] Bluetooth: RFCOMM TTY layer initialized
Tue Mar  5 00:42:43 2019 kern.info kernel: [   15.202295] Bluetooth: RFCOMM socket layer initialized
Tue Mar  5 00:42:43 2019 kern.info kernel: [   15.207470] Bluetooth: RFCOMM ver 1.11
Tue Mar  5 00:42:43 2019 kern.info kernel: [   15.213242] mwifiex_sdio mmc0:0001:1: CMD_RESP: cmd 0x242 error, result=0x2
Tue Mar  5 00:42:43 2019 kern.info kernel: [   15.220270] mwifiex_sdio mmc0:0001:1: mwifiex_process_cmdresp: cmd 0x242 failed during    initialization
Tue Mar  5 00:42:43 2019 kern.info kernel: [   15.231851] xt_time: kernel timezone is -0000
Tue Mar  5 00:42:43 2019 kern.info kernel: [   15.238144] PPP generic driver version 2.4.2
Tue Mar  5 00:42:43 2019 kern.info kernel: [   15.242945] NET: Registered protocol family 24
Tue Mar  5 00:42:43 2019 user.info kernel: [   15.248149] kmodloader: done loading kernel modules from /etc/modules.d/*
Tue Mar  5 00:42:43 2019 kern.info kernel: [   15.280879] mwifiex_sdio mmc0:0001:1: info: MWIFIEX VERSION: mwifiex 1.0 (15.68.7.p71)
Tue Mar  5 00:42:43 2019 kern.info kernel: [   15.288929] mwifiex_sdio mmc0:0001:1: driver_version = mwifiex 1.0 (15.68.7.p71)
Tue Mar  5 00:42:43 2019 user.notice dnsmasq: DNS rebinding protection is active, will discard upstream RFC1918 responses!
Tue Mar  5 00:42:43 2019 daemon.info logread[1570]: failed to send log data to 10.0.10.1:5555 via udp
Tue Mar  5 00:42:43 2019 user.notice dnsmasq: Allowing 127.0.0.0/8 responses
Tue Mar  5 00:42:43 2019 daemon.info dnsmasq[1668]: started, version 2.80 cachesize 150
Tue Mar  5 00:42:43 2019 daemon.info dnsmasq[1668]: DNS service limited to local subnets
Tue Mar  5 00:42:43 2019 daemon.info dnsmasq[1668]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth no-DNSSEC no-ID loop-detect inotify dumpfile
Tue Mar  5 00:42:43 2019 daemon.info dnsmasq[1668]: using local addresses only for domain test
Tue Mar  5 00:42:43 2019 daemon.info dnsmasq[1668]: using local addresses only for domain onion
Tue Mar  5 00:42:43 2019 daemon.info dnsmasq[1668]: using local addresses only for domain localhost
Tue Mar  5 00:42:43 2019 daemon.info dnsmasq[1668]: using local addresses only for domain local
Tue Mar  5 00:42:43 2019 daemon.info dnsmasq[1668]: using local addresses only for domain invalid
Tue Mar  5 00:42:43 2019 daemon.info dnsmasq[1668]: using local addresses only for domain bind
Tue Mar  5 00:42:43 2019 daemon.info dnsmasq[1668]: using local addresses only for domain lan
Tue Mar  5 00:42:43 2019 daemon.warn dnsmasq[1668]: no servers found in /tmp/resolv.conf.auto, will retry
Tue Mar  5 00:42:43 2019 daemon.info dnsmasq[1668]: read /etc/hosts - 4 addresses
Tue Mar  5 00:42:43 2019 daemon.info dnsmasq[1668]: read /tmp/hosts/dhcp.cfg01411c - 0 addresses
Tue Mar  5 00:42:43 2019 authpriv.info dropbear[1695]: Not backgrounding
Tue Mar  5 00:42:43 2019 user.notice : Added device handler type: tunnel
Tue Mar  5 00:42:43 2019 user.notice : Added device handler type: Network device
Tue Mar  5 00:42:43 2019 user.notice : Added device handler type: bridge
Tue Mar  5 00:42:43 2019 user.notice : Added device handler type: veth
Tue Mar  5 00:42:43 2019 user.notice : Added device handler type: macvlan
Tue Mar  5 00:42:43 2019 user.notice : Added device handler type: 8021ad
Tue Mar  5 00:42:43 2019 user.notice : Added device handler type: 8021q
Tue Mar  5 00:42:43 2019 daemon.notice procd: /etc/init.d/network: 'radio2' is disabled
Tue Mar  5 00:42:43 2019 daemon.notice procd: /etc/init.d/network: 'radio2' is disabled
Tue Mar  5 00:42:43 2019 user.notice ucitrack: Setting up /etc/config/network reload dependency on /etc/config/dhcp
Tue Mar  5 00:42:43 2019 user.notice ucitrack: Setting up /etc/config/network reload dependency on /etc/config/radvd
Tue Mar  5 00:42:43 2019 user.notice ucitrack: Setting up /etc/config/wireless reload dependency on /etc/config/network
Tue Mar  5 00:42:43 2019 user.notice ucitrack: Setting up /etc/config/firewall reload dependency on /etc/config/luci-splash
Tue Mar  5 00:42:43 2019 user.notice ucitrack: Setting up /etc/config/firewall reload dependency on /etc/config/qos
Tue Mar  5 00:42:43 2019 user.notice ucitrack: Setting up /etc/config/firewall reload dependency on /etc/config/miniupnpd
Tue Mar  5 00:42:43 2019 user.notice ucitrack: Setting up /etc/config/dhcp reload dependency on /etc/config/odhcpd
Tue Mar  5 00:42:43 2019 user.notice ucitrack: Setting up non-init /etc/config/fstab reload handler: /sbin/block mount
Tue Mar  5 00:42:43 2019 user.notice ucitrack: Setting up /etc/config/system reload trigger for non-procd /etc/init.d/led
Tue Mar  5 00:42:43 2019 user.notice ucitrack: Setting up /etc/config/system reload dependency on /etc/config/luci_statistics
Tue Mar  5 00:42:43 2019 user.notice ucitrack: Setting up /etc/config/system reload dependency on /etc/config/dhcp
Tue Mar  5 00:42:44 2019 kern.info kernel: [   16.425395] mvneta f1034000.ethernet eth0: configuring for fixed/sgmii link mode
Tue Mar  5 00:42:44 2019 kern.info kernel: [   16.432911] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Tue Mar  5 00:42:44 2019 kern.info kernel: [   16.438808] mvneta f1034000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
Tue Mar  5 00:42:44 2019 kern.info kernel: [   16.446898] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Tue Mar  5 00:42:44 2019 kern.info kernel: [   16.454694] br-lan: port 1(eth0.1) entered blocking state
Tue Mar  5 00:42:44 2019 kern.info kernel: [   16.460165] br-lan: port 1(eth0.1) entered disabled state
Tue Mar  5 00:42:44 2019 kern.info kernel: [   16.465718] device eth0.1 entered promiscuous mode
Tue Mar  5 00:42:44 2019 kern.info kernel: [   16.470541] device eth0 entered promiscuous mode
Tue Mar  5 00:42:44 2019 kern.info kernel: [   16.476222] br-lan: port 1(eth0.1) entered blocking state
Tue Mar  5 00:42:44 2019 kern.info kernel: [   16.481680] br-lan: port 1(eth0.1) entered forwarding state
Tue Mar  5 00:42:44 2019 kern.info kernel: [   16.487364] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
Tue Mar  5 00:42:44 2019 daemon.notice netifd: Interface 'lan' is enabled
Tue Mar  5 00:42:44 2019 daemon.notice netifd: Interface 'lan' is setting up now
Tue Mar  5 00:42:44 2019 daemon.notice netifd: Interface 'lan' is now up
Tue Mar  5 00:42:44 2019 daemon.notice netifd: Interface 'loopback' is enabled
Tue Mar  5 00:42:44 2019 daemon.notice netifd: Interface 'loopback' is setting up now
Tue Mar  5 00:42:44 2019 daemon.notice netifd: Interface 'loopback' is now up
Tue Mar  5 00:42:44 2019 daemon.notice procd: /etc/rc.d/S96led: setting up led WAN
Tue Mar  5 00:42:44 2019 kern.info kernel: [   16.499084] mvneta f1070000.ethernet eth1: configuring for fixed/rgmii-id link mode
Tue Mar  5 00:42:44 2019 kern.info kernel: [   16.507362] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
Tue Mar  5 00:42:44 2019 kern.info kernel: [   16.513433] mvneta f1070000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
Tue Mar  5 00:42:44 2019 kern.info kernel: [   16.523133] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
Tue Mar  5 00:42:44 2019 daemon.notice netifd: Interface 'wan' is enabled
Tue Mar  5 00:42:44 2019 daemon.notice netifd: Interface 'wan6' is enabled
Tue Mar  5 00:42:44 2019 daemon.notice netifd: bridge 'br-lan' link is up
Tue Mar  5 00:42:44 2019 daemon.notice netifd: Interface 'lan' has link connectivity
Tue Mar  5 00:42:44 2019 daemon.notice netifd: Network device 'eth0' link is up
Tue Mar  5 00:42:44 2019 daemon.notice netifd: VLAN 'eth0.1' link is up
Tue Mar  5 00:42:44 2019 daemon.notice netifd: Network device 'lo' link is up
Tue Mar  5 00:42:44 2019 daemon.notice procd: /etc/rc.d/S96led: setting up led USB 1
Tue Mar  5 00:42:44 2019 daemon.notice netifd: Interface 'loopback' has link connectivity
Tue Mar  5 00:42:44 2019 daemon.notice netifd: Network device 'eth1' link is up
Tue Mar  5 00:42:44 2019 daemon.notice netifd: VLAN 'eth1.12' link is up
Tue Mar  5 00:42:44 2019 daemon.notice netifd: Interface 'wan' has link connectivity
Tue Mar  5 00:42:44 2019 daemon.notice netifd: Interface 'wan' is setting up now
Tue Mar  5 00:42:44 2019 daemon.notice netifd: Interface 'wan6' has link connectivity
Tue Mar  5 00:42:44 2019 daemon.notice netifd: Interface 'wan6' is setting up now
Tue Mar  5 00:42:44 2019 daemon.notice procd: /etc/rc.d/S96led: setting up led USB 2
Tue Mar  5 00:42:44 2019 daemon.notice procd: /etc/rc.d/S96led: setting up led USB 2 SS
Tue Mar  5 00:42:44 2019 daemon.notice netifd: wan (2080): udhcpc: started, v1.28.4
Tue Mar  5 00:42:44 2019 daemon.err odhcp6c[2074]: Failed to send RS (Address not available)
Tue Mar  5 00:42:44 2019 daemon.info logread[1570]: Logread connected to 10.0.10.1:5555
Tue Mar  5 00:42:44 2019 user.notice firewall: Reloading firewall due to ifup of lan (br-lan)
Tue Mar  5 00:42:44 2019 daemon.notice netifd: wan (2080): udhcpc: sending discover
Tue Mar  5 00:42:44 2019 user.notice mac80211: Failed command: iw phy phy0 set antenna all all
Tue Mar  5 00:42:44 2019 user.notice mac80211: Failed command: iw phy phy1 set antenna all all
Tue Mar  5 00:42:44 2019 daemon.notice netifd: radio0 (2027): command failed: Not supported (-95)
Tue Mar  5 00:42:44 2019 daemon.notice netifd: radio1 (2028): command failed: Not supported (-95)
Tue Mar  5 00:42:44 2019 user.notice mac80211: Failed command: iw phy phy0 set distance 0
Tue Mar  5 00:42:44 2019 user.notice mac80211: Failed command: iw phy phy1 set distance 0
Tue Mar  5 00:42:44 2019 daemon.err odhcp6c[2074]: Failed to send DHCPV6 message to ff02::1:2 (Address not available)
Tue Mar  5 00:42:44 2019 daemon.info procd: - init complete -
Tue Mar  5 00:42:44 2019 daemon.err hostapd: Configuration file: /var/run/hostapd-phy0.conf
Tue Mar  5 00:42:44 2019 daemon.err hostapd: Configuration file: /var/run/hostapd-phy1.conf
Tue Mar  5 00:42:44 2019 kern.debug kernel: [   17.273258] ieee80211 phy0: change: 0xffffffff
Tue Mar  5 00:42:44 2019 kern.info kernel: [   17.379338] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
Tue Mar  5 00:42:45 2019 kern.debug kernel: [   17.558204] ieee80211 phy1: change: 0xffffffff
Tue Mar  5 00:42:45 2019 kern.info kernel: [   17.647358] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
Tue Mar  5 00:42:45 2019 kern.info kernel: [   17.653379] br-lan: port 2(wlan0) entered blocking state
Tue Mar  5 00:42:45 2019 kern.info kernel: [   17.658719] br-lan: port 2(wlan0) entered disabled state
Tue Mar  5 00:42:45 2019 kern.info kernel: [   17.664173] device wlan0 entered promiscuous mode
Tue Mar  5 00:42:45 2019 kern.info kernel: [   17.668926] br-lan: port 2(wlan0) entered blocking state
Tue Mar  5 00:42:45 2019 kern.info kernel: [   17.674271] br-lan: port 2(wlan0) entered forwarding state
Tue Mar  5 00:42:45 2019 daemon.notice hostapd: wlan0: interface state UNINITIALIZED->COUNTRY_UPDATE
Tue Mar  5 00:42:45 2019 kern.info kernel: [   17.679901] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
Tue Mar  5 00:42:45 2019 kern.info kernel: [   17.686973] br-lan: port 2(wlan0) entered disabled state
Tue Mar  5 00:42:45 2019 kern.info kernel: [   17.693189] br-lan: port 3(wlan1) entered blocking state
Tue Mar  5 00:42:45 2019 kern.info kernel: [   17.698534] br-lan: port 3(wlan1) entered disabled state
Tue Mar  5 00:42:45 2019 kern.info kernel: [   17.704004] device wlan1 entered promiscuous mode
Tue Mar  5 00:42:45 2019 daemon.notice hostapd: wlan1: interface state UNINITIALIZED->COUNTRY_UPDATE
Tue Mar  5 00:42:45 2019 daemon.notice netifd: wan (2080): udhcpc: sending select for 188.250.74.185
Tue Mar  5 00:42:45 2019 daemon.err odhcp6c[2074]: Failed to send DHCPV6 message to ff02::1:2 (Address not available)
Tue Mar  5 00:42:45 2019 daemon.notice netifd: wan (2080): udhcpc: lease of 188.250.74.185 obtained, lease time 3600
Tue Mar  5 00:42:45 2019 daemon.notice netifd: Interface 'wan' is now up
Tue Mar  5 00:42:45 2019 daemon.info dnsmasq[1668]: reading /tmp/resolv.conf.auto
Tue Mar  5 00:42:45 2019 daemon.info dnsmasq[1668]: using local addresses only for domain test
Tue Mar  5 00:42:45 2019 daemon.info dnsmasq[1668]: using local addresses only for domain onion
Tue Mar  5 00:42:45 2019 daemon.info dnsmasq[1668]: using local addresses only for domain localhost
Tue Mar  5 00:42:45 2019 daemon.info dnsmasq[1668]: using local addresses only for domain local
Tue Mar  5 00:42:45 2019 daemon.info dnsmasq[1668]: using local addresses only for domain invalid
Tue Mar  5 00:42:45 2019 daemon.info dnsmasq[1668]: using local addresses only for domain bind
Tue Mar  5 00:42:45 2019 daemon.info dnsmasq[1668]: using local addresses only for domain lan
Tue Mar  5 00:42:45 2019 daemon.info dnsmasq[1668]: using nameserver 212.55.154.174#53
Tue Mar  5 00:42:45 2019 daemon.info dnsmasq[1668]: using nameserver 212.55.154.190#53
Tue Mar  5 00:42:45 2019 user.notice firewall: Reloading firewall due to ifup of wan (eth1.12)
Tue Mar  5 00:42:45 2019 daemon.notice hostapd: handle_probe_req: send failed
Tue Mar  5 00:42:46 2019 daemon.notice hostapd: handle_probe_req: send failed
Tue Mar  5 00:42:46 2019 daemon.notice hostapd: handle_probe_req: send failed
Tue Mar  5 00:42:48 2019 daemon.notice hostapd: handle_probe_req: send failed
Tue Mar  5 09:00:06 2019 daemon.notice hostapd: handle_probe_req: send failed
Tue Mar  5 09:00:06 2019 daemon.info dnsmasq[1668]: exiting on receipt of SIGTERM
Tue Mar  5 09:00:06 2019 daemon.info dnsmasq[2970]: started, version 2.80 cachesize 150
Tue Mar  5 09:00:06 2019 daemon.info dnsmasq[2970]: DNS service limited to local subnets
Tue Mar  5 09:00:06 2019 daemon.info dnsmasq[2970]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth no-DNSSEC no-ID loop-detect inotify dumpfile
Tue Mar  5 09:00:06 2019 daemon.info dnsmasq-dhcp[2970]: DHCP, IP range 10.0.0.100 -- 10.0.1.93, lease time 12h
Tue Mar  5 09:00:06 2019 daemon.info dnsmasq[2970]: using local addresses only for domain test
Tue Mar  5 09:00:06 2019 daemon.info dnsmasq[2970]: using local addresses only for domain onion
Tue Mar  5 09:00:06 2019 daemon.info dnsmasq[2970]: using local addresses only for domain localhost
Tue Mar  5 09:00:06 2019 daemon.info dnsmasq[2970]: using local addresses only for domain local
Tue Mar  5 09:00:06 2019 daemon.info dnsmasq[2970]: using local addresses only for domain invalid
Tue Mar  5 09:00:06 2019 daemon.info dnsmasq[2970]: using local addresses only for domain bind
Tue Mar  5 09:00:06 2019 daemon.info dnsmasq[2970]: using local addresses only for domain lan
Tue Mar  5 09:00:06 2019 daemon.info dnsmasq[2970]: reading /tmp/resolv.conf.auto
Tue Mar  5 09:00:06 2019 daemon.info dnsmasq[2970]: using local addresses only for domain test
Tue Mar  5 09:00:06 2019 daemon.info dnsmasq[2970]: using local addresses only for domain onion
Tue Mar  5 09:00:06 2019 daemon.info dnsmasq[2970]: using local addresses only for domain localhost
Tue Mar  5 09:00:06 2019 daemon.info dnsmasq[2970]: using local addresses only for domain local
Tue Mar  5 09:00:06 2019 daemon.info dnsmasq[2970]: using local addresses only for domain invalid
Tue Mar  5 09:00:06 2019 daemon.info dnsmasq[2970]: using local addresses only for domain bind
Tue Mar  5 09:00:06 2019 daemon.info dnsmasq[2970]: using local addresses only for domain lan
Tue Mar  5 09:00:06 2019 daemon.info dnsmasq[2970]: using nameserver 212.55.154.174#53
Tue Mar  5 09:00:06 2019 daemon.info dnsmasq[2970]: using nameserver 212.55.154.190#53
Tue Mar  5 09:00:06 2019 daemon.info dnsmasq[2970]: read /etc/hosts - 4 addresses
Tue Mar  5 09:00:06 2019 daemon.info dnsmasq[2970]: read /tmp/hosts/dhcp.cfg01411c - 1 addresses
Tue Mar  5 09:00:06 2019 daemon.info dnsmasq-dhcp[2970]: read /etc/ethers - 0 addresses
Tue Mar  5 09:00:06 2019 daemon.notice hostapd: handle_probe_req: send failed
Tue Mar  5 09:00:07 2019 daemon.notice hostapd: handle_probe_req: send failed
Tue Mar  5 09:00:07 2019 daemon.notice hostapd: handle_probe_req: send failed
Tue Mar  5 09:00:08 2019 daemon.notice netifd: Interface 'wan6' is now up
Tue Mar  5 09:00:08 2019 daemon.info dnsmasq[2970]: reading /tmp/resolv.conf.auto
Tue Mar  5 09:00:08 2019 daemon.info dnsmasq[2970]: using local addresses only for domain test
Tue Mar  5 09:00:08 2019 daemon.info dnsmasq[2970]: using local addresses only for domain onion
Tue Mar  5 09:00:08 2019 daemon.info dnsmasq[2970]: using local addresses only for domain localhost
Tue Mar  5 09:00:08 2019 daemon.info dnsmasq[2970]: using local addresses only for domain local
Tue Mar  5 09:00:08 2019 daemon.info dnsmasq[2970]: using local addresses only for domain invalid
Tue Mar  5 09:00:08 2019 daemon.info dnsmasq[2970]: using local addresses only for domain bind
Tue Mar  5 09:00:08 2019 daemon.info dnsmasq[2970]: using local addresses only for domain lan
Tue Mar  5 09:00:08 2019 daemon.info dnsmasq[2970]: using nameserver 212.55.154.174#53
Tue Mar  5 09:00:08 2019 daemon.info dnsmasq[2970]: using nameserver 212.55.154.190#53
Tue Mar  5 09:00:08 2019 daemon.info dnsmasq[2970]: using nameserver 2001:8a0:2106:5:212:55:154:174#53
Tue Mar  5 09:00:08 2019 daemon.info dnsmasq[2970]: using nameserver 2001:8a0:2206:5:212:55:154:190#53
Tue Mar  5 09:00:08 2019 user.notice firewall: Reloading firewall due to ifup of wan6 (eth1.12)
Tue Mar  5 09:00:08 2019 daemon.notice hostapd: wlan0: interface state COUNTRY_UPDATE->HT_SCAN
Tue Mar  5 09:00:08 2019 kern.debug kernel: [   22.710474] ieee80211 phy0: change: 0x100
Tue Mar  5 09:00:08 2019 daemon.err hostapd: Using interface wlan1 with hwaddr 24:f5:a2:2d:dd:a9 and ssid "Smells Like Teen Spirit"
Tue Mar  5 09:00:08 2019 kern.debug kernel: [   22.723547] ieee80211 phy0: change: 0x40
Tue Mar  5 09:00:08 2019 kern.debug kernel: [   22.727756] ieee80211 phy1: change: 0x100
Tue Mar  5 09:00:08 2019 kern.debug kernel: [   22.740123] ieee80211 phy1: change: 0x42
Tue Mar  5 09:00:08 2019 kern.info kernel: [   22.879165] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
Tue Mar  5 09:00:08 2019 kern.info kernel: [   22.885619] br-lan: port 3(wlan1) entered blocking state
Tue Mar  5 09:00:08 2019 kern.info kernel: [   22.890967] br-lan: port 3(wlan1) entered forwarding state
Tue Mar  5 09:00:08 2019 daemon.notice hostapd: wlan1: interface state COUNTRY_UPDATE->ENABLED
Tue Mar  5 09:00:08 2019 daemon.notice hostapd: wlan1: AP-ENABLED
Tue Mar  5 09:00:08 2019 kern.debug kernel: [   22.940119] ieee80211 phy0: change: 0x40
Tue Mar  5 09:00:08 2019 daemon.notice netifd: Network device 'wlan1' link is up
Tue Mar  5 09:00:08 2019 daemon.info hostapd: wlan1: STA 2c:3a:e8:4e:a0:47 IEEE 802.11: associated (aid 1)
Tue Mar  5 09:00:08 2019 daemon.notice hostapd: wlan1: AP-STA-CONNECTED 2c:3a:e8:4e:a0:47
Tue Mar  5 09:00:08 2019 daemon.info hostapd: wlan1: STA 00:06:66:93:9f:db IEEE 802.11: associated (aid 2)
Tue Mar  5 09:00:08 2019 daemon.notice hostapd: wlan1: AP-STA-CONNECTED 00:06:66:93:9f:db
Tue Mar  5 09:00:08 2019 kern.debug kernel: [   23.160120] ieee80211 phy0: change: 0x40
Tue Mar  5 09:00:08 2019 kern.debug kernel: [   23.260115] ieee80211 phy0: change: 0x100
Tue Mar  5 09:00:08 2019 daemon.err hostapd: Using interface wlan0 with hwaddr 24:f5:a2:2d:dd:aa and ssid "Smells Like Old"
Tue Mar  5 09:00:08 2019 kern.debug kernel: [   23.273384] ieee80211 phy0: change: 0x100
Tue Mar  5 09:00:08 2019 kern.debug kernel: [   23.286427] ieee80211 phy0: change: 0x42
Tue Mar  5 09:00:09 2019 kern.info kernel: [   23.457122] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
Tue Mar  5 09:00:09 2019 kern.info kernel: [   23.463562] br-lan: port 2(wlan0) entered blocking state
Tue Mar  5 09:00:09 2019 kern.info kernel: [   23.468899] br-lan: port 2(wlan0) entered forwarding state
Tue Mar  5 09:00:09 2019 daemon.notice hostapd: wlan0: interface state HT_SCAN->ENABLED
Tue Mar  5 09:00:09 2019 daemon.notice hostapd: wlan0: AP-ENABLED
Tue Mar  5 09:00:09 2019 daemon.notice netifd: Network device 'wlan0' link is up
Tue Mar  5 09:00:09 2019 daemon.warn odhcpd[1792]: A default route is present but there is no public prefix on br-lan thus we don't announce a default route!
Tue Mar  5 09:00:09 2019 daemon.info hostapd: wlan1: STA 68:c6:3a:95:72:fe IEEE 802.11: associated (aid 3)
Tue Mar  5 09:00:09 2019 daemon.notice hostapd: wlan1: AP-STA-CONNECTED 68:c6:3a:95:72:fe
Tue Mar  5 09:00:11 2019 daemon.info dnsmasq-dhcp[2970]: DHCPDISCOVER(br-lan) 2c:3a:e8:4e:a0:47
Tue Mar  5 09:00:11 2019 daemon.info dnsmasq-dhcp[2970]: DHCPOFFER(br-lan) 10.0.0.189 2c:3a:e8:4e:a0:47
Tue Mar  5 09:00:11 2019 daemon.warn dnsmasq-dhcp[2970]: DHCP packet received on eth1 which has no address
Tue Mar  5 09:00:11 2019 daemon.info dnsmasq[2970]: read /etc/hosts - 4 addresses
Tue Mar  5 09:00:11 2019 daemon.info dnsmasq[2970]: read /tmp/hosts/odhcpd - 0 addresses
Tue Mar  5 09:00:11 2019 daemon.info dnsmasq[2970]: read /tmp/hosts/dhcp.cfg01411c - 1 addresses
Tue Mar  5 09:00:11 2019 daemon.info dnsmasq-dhcp[2970]: read /etc/ethers - 0 addresses
Tue Mar  5 09:00:12 2019 daemon.info hostapd: wlan1: STA 68:c6:3a:95:76:cc IEEE 802.11: associated (aid 4)
Tue Mar  5 09:00:12 2019 daemon.notice hostapd: wlan1: AP-STA-CONNECTED 68:c6:3a:95:76:cc
Tue Mar  5 09:00:14 2019 daemon.info hostapd: wlan1: STA 2c:3a:e8:4e:a0:47 IEEE 802.11: authenticated
Tue Mar  5 09:00:14 2019 daemon.info hostapd: wlan1: STA 00:06:66:93:9f:db IEEE 802.11: authenticated
Tue Mar  5 09:00:14 2019 daemon.info hostapd: wlan1: STA 68:c6:3a:95:72:fe IEEE 802.11: authenticated
Tue Mar  5 09:00:14 2019 daemon.info hostapd: wlan1: STA 68:c6:3a:95:76:cc IEEE 802.11: authenticated
Tue Mar  5 09:00:14 2019 daemon.info hostapd: wlan1: STA d8:63:75:18:1f:c0 IEEE 802.11: associated (aid 5)
Tue Mar  5 09:00:14 2019 daemon.notice hostapd: wlan1: AP-STA-CONNECTED d8:63:75:18:1f:c0
Tue Mar  5 09:00:15 2019 daemon.info dnsmasq-dhcp[2970]: DHCPDISCOVER(br-lan) 00:06:66:93:9f:db
Tue Mar  5 09:00:15 2019 daemon.info dnsmasq-dhcp[2970]: DHCPOFFER(br-lan) 10.0.0.157 00:06:66:93:9f:db
Tue Mar  5 09:00:15 2019 daemon.warn dnsmasq-dhcp[2970]: DHCP packet received on eth1 which has no address
Tue Mar  5 09:00:17 2019 daemon.info hostapd: wlan1: STA 5c:cf:7f:66:c0:b7 IEEE 802.11: associated (aid 6)
Tue Mar  5 09:00:17 2019 daemon.notice hostapd: wlan1: AP-STA-CONNECTED 5c:cf:7f:66:c0:b7
Tue Mar  5 09:00:19 2019 daemon.info dnsmasq-dhcp[2970]: DHCPDISCOVER(br-lan) 68:c6:3a:95:72:fe
Tue Mar  5 09:00:19 2019 daemon.info dnsmasq-dhcp[2970]: DHCPOFFER(br-lan) 10.0.0.111 68:c6:3a:95:72:fe
Tue Mar  5 09:00:19 2019 daemon.warn dnsmasq-dhcp[2970]: DHCP packet received on eth1 which has no address
Tue Mar  5 09:00:19 2019 daemon.info dnsmasq-dhcp[2970]: DHCPDISCOVER(br-lan) 2c:3a:e8:4e:a0:47
Tue Mar  5 09:00:19 2019 daemon.info dnsmasq-dhcp[2970]: DHCPOFFER(br-lan) 10.0.0.189 2c:3a:e8:4e:a0:47
06.03.20192166Base systemBug ReportVery LowHighOpenwrt 18.06.2 build fails when ext4 is not chosen as ...openwrt-18.06Waiting on reporter Task Description

upply the following if possible:
- Raspberry Pi Zero
- 18.06.2
- Go into menu, choose only ‘squashfs’ with defaults and bcm2708 as target. The ‘rootfs’ option disappears, and the build script fails with make world:

Output follows:

./gen_rpi_sdcard_img.sh /data/openwrt/build_dir/target-arm_arm1176jzf-s+vfp_musl_eabi/linux-brcm2708_bcm2708/tmp/openwrt-brcm2708-bcm2708-rpi-squashfs-factory.img.gz /data/openwrt/build_dir/target-arm_arm1176jzf-s+vfp_musl_eabi/linux-brcm2708_bcm2708/tmp/openwrt-brcm2708-bcm2708-rpi-squashfs-factory.img.gz.boot /data/openwrt/build_dir/target-arm_arm1176jzf-s+vfp_musl_eabi/linux-brcm2708_bcm2708/root.squashfs 20
+ '[' 4 -eq 5 ']'
+ echo 'SYNTAX: ./gen_rpi_sdcard_img.sh <file> <bootfs image> <rootfs image> <bootfs size> <rootfs size>'
SYNTAX: ./gen_rpi_sdcard_img.sh <file> <bootfs image> <rootfs image> <bootfs size> <rootfs size>

Looks like the script isn’t passing proper paramaters unless I select ext4 image as well as squashfs image.

17.03.20192192Base systemFeature RequestVery LowHighEFI compatible images neededopenwrt-18.06Unconfirmed Task Description

Currently we are only getting msdos based images for x86_64. Much of the new hardware for that platform is increasingly only UEFI based. Some motherboards allow for a CSM (bios) boot, but not all. I know there is a workaround documented in the wiki, but I was unable to get it to work.

With x86_64 hardware we can get much greater openvpn speeds vs an off the shelf router. This enhancement would be a win for all those wanting to build their own with newer more efficient hardware with excellent AES-NI support.


29.03.20192209Base systemBug ReportVery LowHighInconsistent behaviour of HOST_CONFIGURE_CMD vs CONFIGU...TrunkUnconfirmed Task Description

Target checks via:

if [ -x $(CONFIGURE_CMD) ]; then

yet host does:

if [ -x configure ]; then

So trying to use this, will fail for the target, but not for the host.

CONFIGURE_CMD = ./buildtools/bin/waf configure
HOST_CONFIGURE_CMD = ./buildtools/bin/waf configure

This results in

./buildtools/bin/waf: binary operator expected

for the target.

The check is flawed in both cases, the host does not check for the custom configure command and the target is doing a file check only, so you have to ensure the actual “configure” argument is first in the CONFIGURE_ARGS.

CONFIGURE_ARGS:=configure $(CONFIGURE_ARGS)

This is confusing and both cases should work similar and check for CONFIGURE_CMD and maybe we should add a CONFIGURE_CMD_ARGS variable, that can hold custom arguments.

03.04.20192220Base systemBug ReportVery LowHighath10k NEW kernel thread crash in CT htt firmware - ath...TrunkUnconfirmed Task Description

OpenWrt SNAPSHOT, r9754-fbe2e7d15e
Trunk Pulled April 1st.
Archer C7v2

Unclear how to reproduce, just happens.

Supplying init logs and kernel trace logs:

[ 31.099086] ath10k 4.19 driver, optimized for CT firmware, probing pci device: 0x3c.
[ 31.108127] PCI: Enabling device 0000:00:00.0 (0000 → 0002)
[ 31.116173] ath10k_pci 0000:00:00.0: pci irq legacy oper_irq_mode 1 irq_mode 0 reset_mode 0
[ 31.389333] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/fwcfg-pci-0000:00:00.0.txt failed with error -2
[ 31.400044] ath10k_pci 0000:00:00.0: Falling back to user helper
[ 31.491602] firmware ath10k!fwcfg-pci-0000:00:00.0.txt: firmware_loading_store: map pages failed
[ 31.500774] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:00:00.0.bin failed with error -2
[ 31.511656] ath10k_pci 0000:00:00.0: Falling back to user helper
[ 31.687486] firmware ath10k!pre-cal-pci-0000:00:00.0.bin: firmware_loading_store: map pages failed
[ 31.696848] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/cal-pci-0000:00:00.0.bin failed with error -2
[ 31.707378] ath10k_pci 0000:00:00.0: Falling back to user helper
[ 31.949406] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/ct-firmware-5.bin failed with error -2
[ 31.960559] ath10k_pci 0000:00:00.0: Falling back to user helper
[ 32.095183] firmware ath10k!QCA988X!hw2.0!ct-firmware-5.bin: firmware_loading_store: map pages failed
[ 32.104800] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/ct-firmware-2.bin failed with error -2
[ 32.115944] ath10k_pci 0000:00:00.0: Falling back to user helper
[ 32.291783] firmware ath10k!QCA988X!hw2.0!ct-firmware-2.bin: firmware_loading_store: map pages failed
[ 32.301402] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/firmware-6.bin failed with error -2
[ 32.312279] ath10k_pci 0000:00:00.0: Falling back to user helper
[ 32.487841] firmware ath10k!QCA988X!hw2.0!firmware-6.bin: firmware_loading_store: map pages failed
[ 32.497209] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/firmware-5.bin failed with error -2
[ 32.508092] ath10k_pci 0000:00:00.0: Falling back to user helper
[ 32.684408] firmware ath10k!QCA988X!hw2.0!firmware-5.bin: firmware_loading_store: map pages failed
[ 32.693770] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/firmware-4.bin failed with error -2
[ 32.704646] ath10k_pci 0000:00:00.0: Falling back to user helper
[ 32.879819] firmware ath10k!QCA988X!hw2.0!firmware-4.bin: firmware_loading_store: map pages failed
[ 32.889172] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/firmware-3.bin failed with error -2
[ 32.900050] ath10k_pci 0000:00:00.0: Falling back to user helper
[ 33.076143] firmware ath10k!QCA988X!hw2.0!firmware-3.bin: firmware_loading_store: map pages failed
[ 33.089091] ath10k_pci 0000:00:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000
[ 33.098473] ath10k_pci 0000:00:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[ 33.110860] ath10k_pci 0000:00:00.0: firmware ver 10.1-ct-8x-fW-022-883e26a8 api 2 features wmi-10.x,has-wmi-mgmt-tx,mfp,txstatus-noack,wmi-10.x-CT,ratemask-CT,txrate-CT,get-temp-CT,tx-rc-CT,cust-stats-CT,retry-gt2-CT,txrate2-CT,beacon-cb-CT crc32 7a67ce60
[ 33.219987] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/board-2.bin failed with error -2
[ 33.230599] ath10k_pci 0000:00:00.0: Falling back to user helper
[ 33.382851] firmware ath10k!QCA988X!hw2.0!board-2.bin: firmware_loading_store: map pages failed
[ 33.392104] ath10k_pci 0000:00:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
[ 34.332647] ath10k_pci 0000:00:00.0: 10.1 wmi init: vdevs: 16 peers: 127 tid: 256
[ 34.350100] ath10k_pci 0000:00:00.0: wmi print ‘P 128 V 8 T 410’ [ 34.356422] ath10k_pci 0000:00:00.0: wmi print ‘msdu-desc: 1424 sw-crypt: 0 ct-sta: 0’ [ 34.364543] ath10k_pci 0000:00:00.0: wmi print ‘alloc rem: 24680 iram: 26872’ [ 34.432688] ath10k_pci 0000:00:00.0: htt-ver 2.1 wmi-op 2 htt-op 2 cal file max-sta 128 raw 0 hwcrypto 1
[ 34.445504] ath10k_pci 0000:00:00.0: NOTE: Firmware DBGLOG output disabled in debug_mask: 0×10000000 [ 34.579131] ath: EEPROM regdomain: 0×0 [ 34.579137] ath: EEPROM indicates default country code should be used
[ 34.579140] ath: doing EEPROM country→regdmn map search
[ 34.579152] ath: country maps to regdmn code: 0x3a
[ 34.579158] ath: Country alpha2 being used: US
[ 34.579161] ath: Regpair used: 0x3a
[ 34.652355] ath: EEPROM regdomain: 0×0 [ 34.652362] ath: EEPROM indicates default country code should be used
[ 34.652365] ath: doing EEPROM country→regdmn map search
[ 34.652378] ath: country maps to regdmn code: 0x3a
[ 34.652383] ath: Country alpha2 being used: US
[ 34.652386] ath: Regpair used: 0x3a
[ 34.669837] ieee80211 phy1: Selected rate control algorithm ‘minstrel_ht’ [ 34.671315] ieee80211 phy1: Atheros AR9550 Rev:0 mem=0xb8100000, irq=12 50893 seconds later: [50893.910674] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 1, skipped old beacon
[50893.961879] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[50894.015322] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 1, skipped old beacon
[50894.064267] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[50894.115474] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 1, skipped old beacon
[50894.166670] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[50894.217864] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 1, skipped old beacon
[50894.269072] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[50894.320275] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 1, skipped old beacon
[50894.371474] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[50894.422686] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 1, skipped old beacon
[50894.473885] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[50894.525096] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 1, skipped old beacon
[50894.576362] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[50894.627495] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 1, skipped old beacon
[50894.678696] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[50894.732123] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 1, skipped old beacon
[50894.781096] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[50894.834596] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 1, skipped old beacon
[50894.883493] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[50894.934705] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 1, skipped old beacon
[50894.985904] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
...repeats...
[50896.978515] ath10k_pci 0000:00:00.0: wmi command 36954 timeout, restarting hardware
[50896.986336] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 1, skipped old beacon
[50897.033922] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
...repeats...
[50900.018475] ath10k_pci 0000:00:00.0: wmi command 40859 timeout, restarting hardware
[50900.026455] ath10k_pci 0000:00:00.0: failed to send wmi nop: -11
[50900.032989] ath10k_pci 0000:00:00.0: failed to send pdev bss chan info request: -143
[50900.048476] ath10k_pci 0000:00:00.0: removing peer, cleanup-all, deleting: peer 87385a00 vdev: 0 addr: 50:f5:da:36:35:2c
[50900.059639] ath10k_pci 0000:00:00.0: removing peer, cleanup-all, deleting: peer 85914a00 vdev: 0 addr: ac:bc:32:b4:c4:d7
[50900.070766] ath10k_pci 0000:00:00.0: removing peer, cleanup-all, deleting: peer 86c43400 vdev: 1 addr: 32:b5:c2:96:62:fd
[50900.081883] ath10k_pci 0000:00:00.0: removing peer, cleanup-all, deleting: peer 86e1f000 vdev: 0 addr: 30:b5:c2:96:62:fd
[50900.093145] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 1, skipped old beacon
[50900.355684] ieee80211 phy0: Hardware restart was requested
[50900.361749] ath10k_pci 0000:00:00.0: failed to set beacon mode for vdev 1: -143
[50900.369442] ath10k_pci 0000:00:00.0: failed to set dtim period for vdev 1: -143
[50901.941908] ath10k_pci 0000:00:00.0: 10.1 wmi init: vdevs: 16 peers: 127 tid: 256
[50901.959432] ath10k_pci 0000:00:00.0: wmi print ‘P 128 V 8 T 410’ [50901.965928] ath10k_pci 0000:00:00.0: wmi print ‘msdu-desc: 1424 sw-crypt: 0 ct-sta: 0’ [50901.974101] ath10k_pci 0000:00:00.0: wmi print ‘alloc rem: 24680 iram: 26872’ [50902.043511] ath10k_pci 0000:00:00.0: pdev param 0 not supported by firmware
[50902.058893] ath10k_pci 0000:00:00.0: set-coverage-class, phyclk: 88 value: 0
[50902.079716] ath10k_pci 0000:00:00.0: device successfully recovered
[50902.086147] ath10k_pci 0000:00:00.0: Invalid state: 3 in ath10k_htt_tx_32, warning will not be repeated.
[50902.086152] ————[ cut here ]———— [50902.086232] WARNING: CPU: 0 PID: 4533 at /home/vagrant/openwrt/build_dir/target-mips_24kc_musl/linux-ath79_generic/ath10k-ct-2019-03-25-2e917efb/ath10k-4.19/htt_tx.c:1253 ath10k_convert_hw_rate_to_rate_info+0×190/0xae4 [ath10k_core]
[50902.086235] Modules linked in: ath9k ath9k_common pppoe ppp_async ath9k_hw ath10k_pci ath10k_core ath pppox ppp_generic nf_conntrack_ipv6 mac80211 iptable_nat ipt_REJECT ipt_MASQUERADE cfg80211 xt_time xt_tcpudp xt_tcpmss xt_statistic xt_state xt_recent xt_nat xt_multiport xt_mark xt_mac xt_limit xt_length xt_hl xt_helper xt_ecn xt_dscp xt_conntrack xt_connmark xt_connlimit xt_connbytes xt_comment xt_TRACE xt_TCPMSS xt_REDIRECT xt_LOG xt_HL xt_FLOWOFFLOAD xt_DSCP xt_CT xt_CLASSIFY slhc nf_reject_ipv4 nf_nat_redirect nf_nat_masquerade_ipv4 nf_conntrack_ipv4 nf_nat_ipv4 nf_nat nf_log_ipv4 nf_flow_table_hw nf_flow_table nf_defrag_ipv6 nf_defrag_ipv4 nf_conntrack_rtcache nf_conntrack_netlink iptable_raw iptable_mangle iptable_filter ipt_ECN ip6table_raw ip_tables crc_ccitt compat sch_cake nf_conntrack
[50902.086394] sch_tbf sch_ingress sch_htb sch_hfsc em_u32 cls_u32 cls_tcindex cls_route cls_matchall cls_fw cls_flow cls_basic act_skbedit act_mirred ledtrig_usbport xt_set ip_set_list_set ip_set_hash_netportnet ip_set_hash_netport ip_set_hash_netnet ip_set_hash_netiface ip_set_hash_net ip_set_hash_mac ip_set_hash_ipportnet ip_set_hash_ipportip ip_set_hash_ipport ip_set_hash_ipmark ip_set_hash_ip ip_set_bitmap_port ip_set_bitmap_ipmac ip_set_bitmap_ip ip_set nfnetlink nf_log_ipv6 nf_log_common ip6table_mangle ip6table_filter ip6_tables ip6t_REJECT x_tables nf_reject_ipv6 ifb tun ehci_platform ehci_hcd gpio_button_hotplug usbcore nls_base usb_common
[50902.086515] CPU: 0 PID: 4533 Comm: kworker/0:1 Not tainted 4.14.109 #0
[50902.086640] Workqueue: events_freezable ieee80211_alloc_hw_nm [mac80211]
[50902.086644] Stack : 00000009 000004e5 87d58468 800b2878 804aeb00 87c07cb4 85da4ddc 80501947
[50902.086665] 804aac3c 87c07c8c 80500000 800b36d4 87d58468 00000000 87c07c68 dabdb416
[50902.086684] 00000000 00000000 00000000 00000000 00000004 8040f32c 00000001 68775f6e
[50902.086702] 735f6672 80500000 000001be 65657a61 00000000 00000000 87154274 87124968
[50902.086721] 00000009 000004e5 87d58468 8723cbf0 00000000 00000000 00000000 80650000
[50902.086739] ...
[50902.086745] Call Trace:
[50902.086767] [<8006a90c>] show_stack+0×58/0×100 [50902.086791] [<80084fa0>]
warn+0xe4/0×118 [50902.086802] [<80085064>] warn_slowpath_null+0x1c/0×28 [50902.086866] [<87124968>] ath10k_convert_hw_rate_to_rate_info+0×190/0xae4 [ath10k_core]
[50902.086896] [<87103d04>] 0x87103d04
[50902.086913] —[ end trace db720eb818c982c2 ]— [50902.086925] ath10k_pci 0000:00:00.0: failed to transmit packet, dropping: -19
[50902.086938] ath10k_pci 0000:00:00.0: failed to submit frame: -19
[50902.086945] ath10k_pci 0000:00:00.0: failed to push frame: -19
[50902.086967] ath10k_pci 0000:00:00.0: failed to transmit packet, dropping: -19
[50902.086977] ath10k_pci 0000:00:00.0: failed to submit frame: -19
[50902.086984] ath10k_pci 0000:00:00.0: failed to push frame: -19
[50902.097084] ath10k_pci 0000:00:00.0: failed to transmit packet, dropping: -19
...repeats...
[55789.947757] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 1, skipped old beacon
[55789.998968] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
55792.860153] ath10k_pci 0000:00:00.0: wmi command 36893 timeout, restarting hardware
[55792.867970] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[55792.875741] ath10k_pci 0000:00:00.0: failed to delete peer b0:19:c6:64:f9:69 for vdev 0: -11
[55792.884453] ath10k_pci 0000:00:00.0: found sta peer b0:19:c6:64:f9:69 (ptr 86e1f600 id 33) entry on vdev 0 after it was supposedly removed
[55792.897563] ————[ cut here ]———— [55792.902662] WARNING: CPU: 0 PID: 2420 at backports-4.19.23-1/net/mac80211/sta_info.c:1004 sta_set_sinfo+0xbac/0xc58 [mac80211]
[55792.914415] Modules linked in: ath9k ath9k_common pppoe ppp_async ath9k_hw ath10k_pci ath10k_core ath pppox ppp_generic nf_conntrack_ipv6 mac80211 iptable_nat ipt_REJECT ipt_MASQUERADE cfg80211 xt_time xt_tcpudp xt_tcpmss xt_statistic xt_state xt_recent xt_nat xt_multiport xt_mark xt_mac xt_limit xt_length xt_hl xt_helper xt_ecn xt_dscp xt_conntrack xt_connmark xt_connlimit xt_connbytes xt_comment xt_TRACE xt_TCPMSS xt_REDIRECT xt_LOG xt_HL xt_FLOWOFFLOAD xt_DSCP xt_CT xt_CLASSIFY slhc nf_reject_ipv4 nf_nat_redirect nf_nat_masquerade_ipv4 nf_conntrack_ipv4 nf_nat_ipv4 nf_nat nf_log_ipv4 nf_flow_table_hw nf_flow_table nf_defrag_ipv6 nf_defrag_ipv4 nf_conntrack_rtcache nf_conntrack_netlink iptable_raw iptable_mangle iptable_filter ipt_ECN ip6table_raw ip_tables crc_ccitt compat sch_cake nf_conntrack
[55792.986359] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 1, skipped old beacon
[55792.986485] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[55793.003634] sch_tbf sch_ingress sch_htb sch_hfsc em_u32 cls_u32 cls_tcindex cls_route cls_matchall cls_fw cls_flow cls_basic act_skbedit act_mirred ledtrig_usbport xt_set ip_set_list_set ip_set_hash_netportnet ip_set_hash_netport ip_set_hash_netnet ip_set_hash_netiface ip_set_hash_net ip_set_hash_mac ip_set_hash_ipportnet ip_set_hash_ipportip ip_set_hash_ipport ip_set_hash_ipmark ip_set_hash_ip ip_set_bitmap_port ip_set_bitmap_ipmac ip_set_bitmap_ip ip_set nfnetlink nf_log_ipv6 nf_log_common ip6table_mangle ip6table_filter ip6_tables ip6t_REJECT x_tables nf_reject_ipv6 ifb tun ehci_platform ehci_hcd gpio_button_hotplug usbcore nls_base usb_common
[55793.062374] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 1, skipped old beacon
[55793.070938] CPU: 0 PID: 2420 Comm: hostapd Tainted: G W 4.14.109 #0
[55793.078506] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[55793.086883] Stack : 80520000 804d84a4 00000000 00000000 804aeb00 85da1b04 87dd02dc 80501947
[55793.095767] 804aacd0 00000974 80653670 000003ec 85da1cb4 00000001 85da1ab8 b78f71e9
[55793.104653] 00000000 00000000 80650000 00012a38 00000000 00000000 00000008 00000000
[55793.114085] 000002ce 861a1102 000002cc 00000000 80000000 00000000 87064a04 87007c2c
[55793.123006] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 1, skipped old beacon
[55793.131158] 00000009 000003ec 85da1cb4 87ff8800 00000002 802697c4 00000000 80650000
[55793.139658] ...
[55793.142953] Call Trace:
[55793.145468] [<8006a90c>] show_stack+0×58/0×100 [55793.149997] [<80084fa0>] warn+0xe4/0×118 [55793.154512] [<80085064>] warn_slowpath_null+0x1c/0×28 [55793.160292] [<87007c2c>] sta_set_sinfo+0xbac/0xc58 [mac80211]
[55793.166181] [<87007db8>] sta_info_destroy_addr_bss+0×38/0×60 [mac80211]
[55793.173452] [<8778f17c>] cfg80211_check_station_change+0x1be0/0x2c54 [cfg80211]
[55793.180959] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[55793.188700] —[ end trace db720eb818c982c3 ]— [55793.224635] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 1, skipped old beacon
[55793.275831] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
...
[55796.220118] ath10k_pci 0000:00:00.0: wmi command 36954 timeout, restarting hardware
[55796.245481] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[55796.296663] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 1, skipped old beacon
[55796.317807] ath10k_pci 0000:00:00.0: removing peer, cleanup-all, deleting: peer 8561b600 vdev: 0 addr: 50:f5:da:36:35:2c
[55796.328987] ath10k_pci 0000:00:00.0: removing peer, cleanup-all, deleting: peer 85322c00 vdev: 0 addr: ac:bc:32:b4:c4:d7
[55796.340121] ath10k_pci 0000:00:00.0: removing peer, cleanup-all, deleting: peer 834fb200 vdev: 1 addr: 32:b5:c2:96:62:fd
[55796.351253] ath10k_pci 0000:00:00.0: removing peer, cleanup-all, deleting: peer 834fb000 vdev: 0 addr: 30:b5:c2:96:62:fd
[55796.860635] irq 15: nobody cared (try booting with the “irqpoll” option)
[55796.867447] CPU: 0 PID: 15620 Comm: kworker/u2:0 Tainted: G W 4.14.109 #0
[55796.875540] Workqueue: ath10k_wq ath10k_core_create [ath10k_core]
[55796.881718] Stack : ffffffff 00000003 80653ae0 800b2878 804aeb00 87c07cc4 86e123dc 80501947
[55796.890201] 804aac3c 87c07c9c 80500000 800b36d4 80653ae0 00000000 87c07c78 86c8eb6e
[55796.898683] 00000000 00000000 00000000 000151c0 00000000 00000000 00000008 00000000
[55796.907167] 00000323 80500000 00000322 00000000 00000000 8050b6a4 0000000f 00011000
[55796.915650] ffffffff 00000003 80653ae0 80506ae8 00000000 802697c4 00000000 80650000
[55796.924134] ...
[55796.926615] Call Trace:
[55796.929112] [<8006a90c>] show_stack+0×58/0×100 [55796.933620] [<800b6f6c>]
report_bad_irq.isra.0+0×54/0xf0
[55796.939179] [<800b72f4>] note_interrupt+0×284/0×330 [55796.944142] [<800b488c>] handle_irq_event_percpu+0x4c/0×64 [55796.949706] [<800b48e0>] handle_irq_event+0x3c/0x6c
[55796.954650] [<800b7ca4>] handle_level_irq+0×110/0×154 [55796.959772] [<800b3d90>] generic_handle_irq+0×38/0×50 [55796.964903] [<802d4750>] ar724x_pci_irq_handler+0xa4/0xdc
[55796.970376] [<800b3d90>] generic_handle_irq+0×38/0×50 [55796.975502] [<80219354>] ath79_intc_irq_handler+0×94/0xec
[55796.980981] [<800b3d90>] generic_handle_irq+0×38/0×50 [55796.986117] [<804144d4>] do_IRQ+0x1c/0x2c
[55796.990185] [<80219260>] plat_irq_dispatch+0xc0/0×120 [55796.995306] [<800658d8>] handle_int+0×138/0×144 [55796.999900] [<80219260>] plat_irq_dispatch+0xc0/0×120 [55797.005018] handlers:
[55797.007333] [<877134a0>] ath10k_pci_irq_msi_fw_mask [ath10k_pci]
[55797.013420] Disabling IRQ #15
[55797.285000] ieee80211 phy0: Hardware restart was requested
[55800.300248] ath10k_pci 0000:00:00.0: bss channel survey timed out
[55801.740207] ath10k_pci 0000:00:00.0: 10.1 wmi init: vdevs: 16 peers: 127 tid: 256
[55801.850097] ath10k_pci 0000:00:00.0: wmi print ‘P 128 V 8 T 410’ [55801.856213] ath10k_pci 0000:00:00.0: wmi print ‘msdu-desc: 1424 sw-crypt: 0 ct-sta: 0’ [55801.864353] ath10k_pci 0000:00:00.0: wmi print ‘alloc rem: 24680 iram: 26872’ [55802.950176] ath10k_pci 0000:00:00.0: pdev param 0 not supported by firmware
[55808.120391] ath10k_pci 0000:00:00.0: device successfully recovered
[55808.126726] net_ratelimit: 79 callbacks suppressed
[55808.126736] ath10k_pci 0000:00:00.0: failed to transmit packet, dropping: -19
[55808.126748] ath10k_pci 0000:00:00.0: failed to submit frame: -19
[55808.126756] ath10k_pci 0000:00:00.0: failed to push frame: -19
[55808.126771] ath10k_pci 0000:00:00.0: failed to transmit packet, dropping: -19
[55808.126780] ath10k_pci 0000:00:00.0: failed to submit frame: -19
[55808.126787] ath10k_pci 0000:00:00.0: failed to push frame: -19
[55808.560031] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 1, skipped old beacon
[55808.567607] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[55808.575152] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 1, skipped old beacon
[55808.670084] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[55808.677616] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 1, skipped old beacon
[55808.790161] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[55808.797700] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 1, skipped old beacon
[55808.890070] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[55808.897614] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 1, skipped old beacon
[55809.000079] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[55809.007588] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 1, skipped old beacon
[55809.110035] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[55809.117559] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 1, skipped old beacon
[55809.125363] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[55809.220094] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 1, skipped old beacon
[55809.227789] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[55809.330097] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 1, skipped old beacon
[55809.337638] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[55809.440112] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 1, skipped old beacon
[55809.447645] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[55809.550389] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 1, skipped old beacon
[55809.557931] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[55809.660388] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 1, skipped old beacon


06.04.20192226Base systemBug ReportVery LowHighzyxel P-2812HNU-F1 initramfs has been broken with LZMA:...AllUnconfirmed Task Description

Supply the following if possible:
- Device problem occurs on

zyxel P-2812HNU-F1

- Software versions of OpenWrt/LEDE release, packages, etc.

since r47026 up to the latest trunk

- Steps to reproduce
boot with serial connection stop autoboot, load initramfs, boot from ram get error

- Reason it is important

initramfs is needed for a first install.

- Posible solution
include/configs/p2812hnufx.h
probably needs:
#define CONFIG_SYS_BOOTM_LEN 0×1000000 /* 16 MB */

like in this commit for a similar modem
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=ea12a80276c0aca680d67515e7f651e2cef3f3ee

- error logs
“recent” trunk snapshot(I threw away the last compiled version for it still gave the same error)

ROM VER: 1.0.5
CFG 06
NAND
NAND Read OK

U-Boot SPL 2013.10-openwrt5 (Nov 18 2014 - 19:54:01)
SPL: initializing NAND flash
SPL: checking U-Boot image
SPL: loading U-Boot to RAM
SPL: decompressing U-Boot with LZO
SPL: jumping to U-Boot


U-Boot 2013.10-openwrt5 (Nov 18 2014 - 19:54:01) P-2812HNU-Fx

Board: ZyXEL P-2812HNU-Fx
SoC:   Lantiq VRX288 v1.1
CPU:   500 MHz
IO:    250 MHz
BUS:   250 MHz
BOOT:  NAND
DRAM:  128 MiB
NAND:  128 MiB
In:    serial
Out:   serial
Err:   serial
Net:   ltq-eth
Hit any key to stop autoboot:  0
P-2812HNU-Fx # tftpboot openwrt-lantiq-xrx200-zyxel_p-2812hnu-f1-initramfs-kernel.bin
ltq_phy: addr 0, link 1, speed 1000, duplex 1
ltq_phy: addr 1, link 0, speed 10, duplex 0
ltq_phy: addr 17, link 0, speed 10, duplex 0
ltq_phy: addr 19, link 0, speed 10, duplex 0
ltq_phy: addr 5, link 0, speed 10, duplex 0
Using ltq-eth device
TFTP from server 192.168.1.2; our IP address is 192.168.1.1
Filename 'openwrt-lantiq-xrx200-zyxel_p-2812hnu-f1-initramfs-kernel.bin'.
Load address: 0x81000000
Loading: #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         ######################################
done
Bytes transferred = 6183929 (5e5bf9 hex)
P-2812HNU-Fx # bootm $fileaddr
## Booting kernel from Legacy Image at 81000000 ...
   Image Name:   MIPS OpenWrt Linux-4.14.103
   Created:      2019-02-27  11:12:48 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    6183865 Bytes = 5.9 MiB
   Load Address: 80002000
   Entry Point:  80002000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... LZMA: uncompress or overwrite error 7 - must RESET b
ROM VER: 1.0.5
CFG 06
NAND
NAND Read OK

U-Boot SPL 2013.10-openwrt5 (Nov 18 2014 - 19:54:01)

last known working version

ROM VER: 1.0.5
CFG 06
NAND
NAND Read OK

U-Boot SPL 2013.10-openwrt5 (Nov 18 2014 - 19:54:01)
SPL: initializing NAND flash
SPL: checking U-Boot image
SPL: loading U-Boot to RAM
SPL: decompressing U-Boot with LZO
SPL: jumping to U-Boot


U-Boot 2013.10-openwrt5 (Nov 18 2014 - 19:54:01) P-2812HNU-Fx

Board: ZyXEL P-2812HNU-Fx
SoC:   Lantiq VRX288 v1.1
CPU:   500 MHz
IO:    250 MHz
BUS:   250 MHz
BOOT:  NAND
DRAM:  128 MiB
NAND:  128 MiB
In:    serial
Out:   serial
Err:   serial
Net:   ltq-eth
Hit any key to stop autoboot:  0
P-2812HNU-Fx # tftpboot openwrt-lantiq-xrx200-P2812HNUF1-uImage-initramfs
ltq_phy: addr 0, link 0, speed 10, duplex 0
ltq_phy: addr 1, link 0, speed 10, duplex 0
ltq_phy: addr 17, link 0, speed 10, duplex 0
ltq_phy: addr 19, link 0, speed 10, duplex 0
ltq_phy: addr 5, link 0, speed 10, duplex 0
Using ltq-eth device
TFTP from server 192.168.1.2; our IP address is 192.168.1.1
Filename 'openwrt-lantiq-xrx200-P2812HNUF1-uImage-initramfs'.
Load address: 0x81000000
Loading: T T T T T T T T T T
Retry count exceeded; starting again
ltq_phy: addr 0, link 1, speed 1000, duplex 1
ltq_phy: addr 1, link 0, speed 10, duplex 0
ltq_phy: addr 17, link 0, speed 10, duplex 0
ltq_phy: addr 19, link 0, speed 10, duplex 0
ltq_phy: addr 5, link 0, speed 10, duplex 0
Using ltq-eth device
TFTP from server 192.168.1.2; our IP address is 192.168.1.1
Filename 'openwrt-lantiq-xrx200-P2812HNUF1-uImage-initramfs'.
Load address: 0x81000000
Loading: #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         ##########
         1.6 MiB/s
done
Bytes transferred = 4707233 (47d3a1 hex)
P-2812HNU-Fx # bootm $fileaddr
## Booting kernel from Legacy Image at 81000000 ...
   Image Name:   MIPS OpenWrt Linux-3.18.11
   Created:      2015-04-25   1:54:58 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    4707169 Bytes = 4.5 MiB
   Load Address: 80002000
   Entry Point:  80002000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK

Starting kernel ...

[    0.000000] Linux version 3.18.11 (sylwek@WRT) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r44945) ) #2 Sat Apr 25 03:54:35 CEST 2015
[    0.000000] SoC: VR9 rev 1.1
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019555 (MIPS 34Kc)
[    0.000000] MIPS: machine is P2812HNUF1 - ZyXEL P-2812HNU-F1
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x07ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x07ffffff]
[    0.000000] Initmem setup node 0 [mem 0x00000000-0x07ffffff]
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=00021000
[    0.000000] Readback ErrCtl register=00021000
[    0.000000] Memory: 121772K/131072K available (3506K kernel code, 149K rwdata, 1036K rodata, 3160K init, 206K bss, 9300K reserved)
[    0.000000] NR_IRQS:256
[    0.000000] CPU Clock: 500MHz
[    0.000000] Calibrating delay loop... 332.54 BogoMIPS (lpj=665088)
[    0.032000] pid_max: default: 32768 minimum: 301
[    0.036000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.040000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.044000] pinctrl core: initialized pinctrl subsystem
[    0.048000] NET: Registered protocol family 16
[    0.056000] pinctrl-xway 1e100b10.pinmux: Init done
[    0.060000] dma-xway 1e104100.dma: Init done - hw rev: 7, ports: 7, channels: 28
[    0.164000] dcdc-xrx200 1f106a00.dcdc: Core Voltage : 1016 mV
[    0.168000] PCI host bridge /fpi@10000000/pci@E105400 ranges:
[    0.172000]  MEM 0x0000000018000000..0x0000000019ffffff
[    0.176000]   IO 0x000000001ae00000..0x000000001affffff
[    0.188000] gpio-stp-xway 1e100bb0.stp: Init done
[    0.192000] usbcore: registered new interface driver usbfs
[    0.196000] usbcore: registered new interface driver hub
[    0.200000] usbcore: registered new device driver usb
[    0.204000] PCI host bridge to bus 0000:00
[    0.208000] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff]
[    0.212000] pci_bus 0000:00: root bus resource [io  0xffffffff]
[    0.216000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.220000] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff]
[    0.224000] Switched to clocksource MIPS
[    0.228000] NET: Registered protocol family 2
[    0.232000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.240000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.248000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.252000] TCP: reno registered
[    0.256000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.260000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.268000] NET: Registered protocol family 1
[    5.124000] gptu: totally 6 16-bit timers/counters
[    5.132000] gptu: misc_register on minor 63
[    5.136000] gptu: succeeded to request irq 126
[    5.140000] gptu: succeeded to request irq 127
[    5.144000] gptu: succeeded to request irq 128
[    5.148000] gptu: succeeded to request irq 129
[    5.152000] gptu: succeeded to request irq 130
[    5.156000] gptu: succeeded to request irq 131
[    5.164000] ralink,eeprom ralink_eep: using RT3062.eeprom as eeprom
[    5.168000] phy-xrx200 gphy-xrx200: requesting lantiq/vr9_phy11g_a1x.bin
[    5.176000] phy-xrx200 gphy-xrx200: booting GPHY0 firmware at 6A60000
[    5.184000] phy-xrx200 gphy-xrx200: booting GPHY1 firmware at 6A60000
[    5.288000] futex hash table entries: 256 (order: -1, 3072 bytes)
[    5.296000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    5.304000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    5.312000] msgmni has been set to 237
[    5.316000] io scheduler noop registered
[    5.320000] io scheduler deadline registered (default)
[    5.328000] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112, base_baud = 0) is a lantiq,asc
[    5.336000] console [ttyLTQ0] enabled
[    5.336000] console [ttyLTQ0] enabled
[    5.344000] bootconsole [early0] disabled
[    5.344000] bootconsole [early0] disabled
[    5.352000] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xf1
[    5.352000] nand: Samsung NAND 128MiB 3,3V 8-bit
[    5.352000] nand: 128MiB, SLC, page size: 2048, OOB size: 64
[    5.368000] Scanning device for bad blocks
[    5.424000] Bad eraseblock 591 at 0x0000049e0000
[    5.428000] Bad eraseblock 616 at 0x000004d00000
[    5.464000] 4 ofpart partitions found on MTD device 10000000.nand-parts
[    5.468000] Creating 4 MTD partitions on "10000000.nand-parts":
[    5.476000] 0x000000000000-0x000000040000 : "uboot"
[    5.480000] 0x000000040000-0x000000060000 : "uboot-env"
[    5.488000] 0x000000060000-0x000000260000 : "kernel"
[    5.492000] 0x000000260000-0x000008000000 : "ubi"
[    5.600000] libphy: lantiq,xrx200-mdio: probed
[    5.620000] net-xrx200: invalid MAC, using random
[    5.688000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.3] (phy_addr=0:00, irq=-1)
[    5.756000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.3] (phy_addr=0:01, irq=-1)
[    5.824000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:11, irq=-1)
[    5.892000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:13, irq=-1)
[    5.960000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.3] (phy_addr=0:05, irq=-1)
[    5.968000] wdt 1f8803f0.watchdog: Init done
[    5.972000] TCP: cubic registered
[    5.976000] NET: Registered protocol family 17
[    5.980000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    5.992000] Bridge firewalling registered
[    5.996000] 8021q: 802.1Q VLAN Support v1.8
[    6.004000] UBI error: ubi_auto_attach: no valid UBI magic found [    6.016000] Freeing unused kernel memory: 3160K (8049a000 - 807b0000)
[    6.036000] init: failed to symlink /tmp -> /var
[    6.040000] init: Console is alive
[    6.048000] init: - watchdog -
[    6.076000] dwc2 1e101000.ifxhcd: requested GPIO 489
[    6.936000] dwc2 1e101000.ifxhcd: DWC OTG Controller
[    6.936000] dwc2 1e101000.ifxhcd: new USB bus registered, assigned bus number 1
[    6.944000] dwc2 1e101000.ifxhcd: irq 62, io mem 0x00000000
[    6.952000] dwc2 1e101000.ifxhcd: Hardware does not support descriptor DMA mode -
[    6.952000] dwc2 1e101000.ifxhcd: falling back to buffer DMA mode.
[    6.964000] hub 1-0:1.0: USB hub found
[    6.968000] hub 1-0:1.0: 1 port detected
[    7.832000] dwc2 1e106000.ifxhcd: DWC OTG Controller
[    7.832000] dwc2 1e106000.ifxhcd: new USB bus registered, assigned bus number 2
[    7.840000] dwc2 1e106000.ifxhcd: irq 91, io mem 0x00000000
[    7.848000] dwc2 1e106000.ifxhcd: Hardware does not support descriptor DMA mode -
[    7.848000] dwc2 1e106000.ifxhcd: falling back to buffer DMA mode.
[    7.860000] hub 2-0:1.0: USB hub found
[    7.864000] hub 2-0:1.0: 1 port detected
[    8.048000] init: - preinit -
[    8.160000] random: procd urandom read with 31 bits of entropy available
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    9.688000] eth0: port 0 got link
[   11.280000] procd: - early -
[   11.280000] procd: - watchdog -
[   11.852000] procd: - ubus -
[   12.864000] procd: - init -
Please press Enter to activate this console.
[   13.884000] IFXOS, Version 1.5.14 (c) Copyright 2009, Lantiq Deutschland GmbH

[   13.908000] NET: Registered protocol family 10
[   13.916000] NET: Registered protocol family 8
[   13.920000] NET: Registered protocol family 20
[   13.932000] PPP generic driver version 2.4.2
[   13.940000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   13.964000] MEI CPE Driver, Version 1.2.0

[   13.964000] (c) Copyright 2009, Infineon Technologies AG
### MEI CPE - MEI CPE - MEI CPE - MEI CPE ###


Lantiq CPE API Driver version: DSL CPE API V4.11.4
[   13.988000]
[   13.988000] Predefined debug level: 2
[   14.000000] Loading modules backported from Linux version master-2015-03-09-0-g141f155
[   14.004000] Backport generated by backports.git backports-20150129-0-gdd4a670
[   14.016000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   14.028000] Infineon Technologies DEU driver version 2.0.0
[   14.032000] IFX DEU DES initialized (multiblock).
[   14.036000] IFX DEU AES initialized (multiblock).
[   14.040000] IFX DEU ARC4 initialized (multiblock).
[   14.044000] IFX DEU SHA1 initialized.
[   14.048000] IFX DEU MD5 initialized.
[   14.052000] IFX DEU SHA1_HMAC initialized.
[   14.056000] IFX DEU MD5_HMAC initialized.
[   14.068000] nf_conntrack version 0.5.0 (1952 buckets, 7808 max)
[   14.092000] NET: Registered protocol family 24
[   14.116000] xt_time: kernel timezone is -0000
[   14.140000] cfg80211: Calling CRDA to update world regulatory domain
[   14.164000] cfg80211: World regulatory domain updated:
[   14.168000] cfg80211:  DFS Master region: unset
[   14.172000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   14.180000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   14.188000] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   14.196000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[   14.204000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[   14.212000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[   14.220000] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[   14.232000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[   14.240000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[   14.328000] PCI: Enabling device 0000:00:0e.0 (0000 -> 0002)
[   14.332000] rt2800pci 0000:00:0e.0: failed to load eeprom property
[   14.336000] ieee80211 phy0: rt2x00lib_request_eeprom_file: Info - Loading EEPROM data from 'RT3062.eeprom'.
[   14.348000] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 3572, rev 0223 detected
[   14.356000] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 0008 detected
ioctl ATM_SETESI: No such device
[   20.824000] PTM 1.0.27    PTM (E1) firmware version 0.30
[   20.828000] ifxmips_ptm: PTM init succeed
[   22.760000] device eth0.1 entered promiscuous mode
[   22.764000] device eth0 entered promiscuous mode
[   22.776000] br-lan: port 1(eth0.1) entered forwarding state
[   22.780000] br-lan: port 1(eth0.1) entered forwarding state
[   24.784000] br-lan: port 1(eth0.1) entered forwarding state
[   31.808000] random: nonblocking pool is initialized



BusyBox v1.23.2 (2015-04-25 03:40:56 CEST) built-in shell (ash)

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 -----------------------------------------------------
 CHAOS CALMER (Bleeding Edge, r45578)
 -----------------------------------------------------
  * 1 1/2 oz Gin            Shake with a glassful
  * 1/4 oz Triple Sec       of broken ice and pour
  * 3/4 oz Lime Juice       unstrained into a goblet.
  * 1 1/2 oz Orange Juice
  * 1 tsp. Grenadine Syrup
 -----------------------------------------------------
root@OpenWrt:/#
17.04.20192240Base systemBug ReportVery LowHighLantiq: AVM FRITZ!Box 7320 only one ETH port is workingAllUnconfirmed Task Description

Router has 2 ethernet ports, but the only first one is working.

02.05.20192264Base systemBug ReportVery LowHighlibc.so kernel error: do_page_fault(): sending SIGSEGV ...TrunkWaiting on reporter Task Description

newest trunk: OpenWrt SNAPSHOT r9915-d6643ac

Thu May  2 03:19:52 2019 kern.info kernel: [ 1729.225129] do_page_fault(): sending SIGSEGV to exec read for invalid write access to 00000000
Thu May  2 03:19:52 2019 kern.info kernel: [ 1729.225143] do_page_fault(): sending SIGSEGV to exec read for invalid write access to 00000000
Thu May  2 03:19:52 2019 kern.info kernel: [ 1729.225166] epc = 77f271a0 in
Thu May  2 03:19:52 2019 kern.info kernel: [ 1729.233799] epc = 77f271a0 in
Thu May  2 03:19:52 2019 kern.warn kernel: [ 1729.242495]  libc.so[77efe000+95000]
Thu May  2 03:19:52 2019 kern.warn kernel: [ 1729.245440]  libc.so[77efe000+95000]
Thu May  2 03:19:52 2019 kern.info kernel: [ 1729.248402] ra  = 77f1b4b4 in libc.so[77efe000+95000]
Thu May  2 03:19:52 2019 kern.info kernel: [ 1729.252079] ra  = 77f1b4b4 in
Thu May  2 03:19:52 2019 kern.warn kernel: [ 1729.263788]  libc.so[77efe000+95000]
22.06.20192332Base systemBug ReportVery LowHighCustom DNS servers settings not work on WAN6 interface openwrt-18.06Waiting on reporter Task Description

Supply the following if possible:
- Device problem occurs on
x86-64 virtual machine hosted by ESXI6.7u2

- Software versions of OpenWrt/LEDE release, packages, etc.
OpenWrt 18.06.2 r7676-cddd7b4c77 / LuCI openwrt-18.06 branch (git-19.170.32094-4d6d8bc)

- Steps to reproduce
all steps performed on LUCI
1. Set WAN interface to ignore peer DNS to use custom DNS 127.0.0.1
2. Set WAN6 interface to ignore peer DNS to use custom DNS ::1
3. Start WAN (PPPOE) and WAN6 (DNCPv6 client)

issue: Check effective DNS, custom WAN6 DNS setting is ignored

/tmp/resolv.conf.auto
# Interface lan
nameserver 127.0.0.1
# Interface wan
nameserver 127.0.0.1
# Interface wan_6
nameserver 240e:58:c000:1600:180:168:255:118
nameserver 240e:58:c000:1000:116:228:111:18


16.07.20192390Base systemBug ReportVery LowHighIssues with PowerLAN devicesTrunkUnconfirmed Task Description

Since switching my WNDR3700v1 from Netgear’s firmware to OpenWrt 18.06.2 r7676-cddd7b4c77, I am experiencing the following issues:

1) PowerLAN adapters and network devices connected through it are only seen by the router if the first PowerLAN adapter is connected through a crossover cable. With the manufacturer’s firmware, it was possible to connect the adapter by standard ethernet cable.

2) A printer connected through PowerLAN does not get assigned an IP4 network address, even though I have defined a static address for it in the DHCP section of OpenWrt; (it does get an IPv6 address though). The missing IP4 network address prevents the scanner part of the printer from sending scans to a network folder on my NAS connected through ethernet cable to the router. This issue also did not exist with the original Netgear firmware.

 


27.07.20192411Base systemBug ReportVery LowHighChanges to configuration are not saved between reboots ...openwrt-18.06Waiting on reporter Task Description

I recently updated my D-Link DIR-600 to OpenWrt 18.06.4. As I recall, the previous running version was from the 17.* branch line which worked like a charm. Since the update to 18, the configuration is no longer saved when altered (through LuCI). I suspect the flash size may be too small for this device.

kern.err kernel: [   44.315763] jffs2: Too few erase blocks (4)

System log as follows:

Thu Jun 27 12:19:01 2019 kern.notice kernel: [    0.000000] Linux version 4.14.131 (buildbot@dbab1e23488d) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r7808-ef686b7292)) #0 Thu Jun 27 12:18:52 2019
Thu Jun 27 12:19:01 2019 kern.info kernel: [    0.000000] SoC Type: Ralink RT3350 id:1 rev:2
Thu Jun 27 12:19:01 2019 kern.info kernel: [    0.000000] bootconsole [early0] enabled
Thu Jun 27 12:19:01 2019 kern.info kernel: [    0.000000] CPU0 revision is: 0001964c (MIPS 24KEc)
Thu Jun 27 12:19:01 2019 kern.info kernel: [    0.000000] MIPS: machine is D-Link DIR-600 B1
Thu Jun 27 12:19:01 2019 kern.info kernel: [    0.000000] Determined physical RAM map:
Thu Jun 27 12:19:01 2019 kern.info kernel: [    0.000000]  memory: 02000000 @ 00000000 (usable)
Thu Jun 27 12:19:01 2019 kern.info kernel: [    0.000000] Initrd not found or empty - disabling initrd
Thu Jun 27 12:19:01 2019 kern.warn kernel: [    0.000000] Primary instruction cache 16kB, VIPT, 4-way, linesize 32 bytes.
Thu Jun 27 12:19:01 2019 kern.warn kernel: [    0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
Thu Jun 27 12:19:01 2019 kern.info kernel: [    0.000000] Zone ranges:
Thu Jun 27 12:19:01 2019 kern.info kernel: [    0.000000]   Normal   [mem 0x0000000000000000-0x0000000001ffffff]
Thu Jun 27 12:19:01 2019 kern.info kernel: [    0.000000] Movable zone start for each node
Thu Jun 27 12:19:01 2019 kern.info kernel: [    0.000000] Early memory node ranges
Thu Jun 27 12:19:01 2019 kern.info kernel: [    0.000000]   node   0: [mem 0x0000000000000000-0x0000000001ffffff]
Thu Jun 27 12:19:01 2019 kern.info kernel: [    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000001ffffff]
Thu Jun 27 12:19:01 2019 kern.debug kernel: [    0.000000] On node 0 totalpages: 8192
Thu Jun 27 12:19:01 2019 kern.debug kernel: [    0.000000] free_area_init_node: node 0, pgdat 803f74b0, node_mem_map 81000040
Thu Jun 27 12:19:01 2019 kern.debug kernel: [    0.000000]   Normal zone: 64 pages used for memmap
Thu Jun 27 12:19:01 2019 kern.debug kernel: [    0.000000]   Normal zone: 0 pages reserved
Thu Jun 27 12:19:01 2019 kern.debug kernel: [    0.000000]   Normal zone: 8192 pages, LIFO batch:0
Thu Jun 27 12:19:01 2019 kern.notice kernel: [    0.000000] random: get_random_bytes called from 0x803fa730 with crng_init=0
Thu Jun 27 12:19:01 2019 kern.debug kernel: [    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
Thu Jun 27 12:19:01 2019 kern.debug kernel: [    0.000000] pcpu-alloc: [0] 0
Thu Jun 27 12:19:01 2019 kern.info kernel: [    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 8128
Thu Jun 27 12:19:01 2019 kern.notice kernel: [    0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
Thu Jun 27 12:19:01 2019 kern.info kernel: [    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
Thu Jun 27 12:19:01 2019 kern.info kernel: [    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Thu Jun 27 12:19:01 2019 kern.info kernel: [    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Thu Jun 27 12:19:01 2019 kern.info kernel: [    0.000000] Writing ErrCtl register=0003fbe0
Thu Jun 27 12:19:01 2019 kern.info kernel: [    0.000000] Readback ErrCtl register=0003fbe0
Thu Jun 27 12:19:01 2019 kern.info kernel: [    0.000000] Memory: 27968K/32768K available (3463K kernel code, 172K rwdata, 428K rodata, 152K init, 202K bss, 4800K reserved, 0K cma-reserved)
Thu Jun 27 12:19:01 2019 kern.info kernel: [    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Thu Jun 27 12:19:01 2019 kern.info kernel: [    0.000000] NR_IRQS: 256
Thu Jun 27 12:19:01 2019 kern.info kernel: [    0.000000] CPU Clock: 320MHz
Thu Jun 27 12:19:01 2019 kern.crit kernel: [    0.000000] timer_probe: no matching timers found
Thu Jun 27 12:19:01 2019 kern.info kernel: [    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11945377789 ns
Thu Jun 27 12:19:01 2019 kern.info kernel: [    0.000027] sched_clock: 32 bits at 160MHz, resolution 6ns, wraps every 13421772796ns
Thu Jun 27 12:19:01 2019 kern.info kernel: [    0.015794] Calibrating delay loop... 212.58 BogoMIPS (lpj=1062912)
Thu Jun 27 12:19:01 2019 kern.info kernel: [    0.108400] pid_max: default: 32768 minimum: 301
Thu Jun 27 12:19:01 2019 kern.info kernel: [    0.118144] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Thu Jun 27 12:19:01 2019 kern.info kernel: [    0.131389] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
Thu Jun 27 12:19:01 2019 kern.info kernel: [    0.158707] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
Thu Jun 27 12:19:01 2019 kern.info kernel: [    0.178376] futex hash table entries: 256 (order: -1, 3072 bytes)
Thu Jun 27 12:19:01 2019 kern.info kernel: [    0.190778] pinctrl core: initialized pinctrl subsystem
Thu Jun 27 12:19:01 2019 kern.info kernel: [    0.204961] NET: Registered protocol family 16
Thu Jun 27 12:19:01 2019 kern.info kernel: [    0.288107] rt2880_gpio 10000600.gpio: registering 24 gpios
Thu Jun 27 12:19:01 2019 kern.info kernel: [    0.299345] rt2880_gpio 10000600.gpio: registering 24 irq handlers
Thu Jun 27 12:19:01 2019 kern.info kernel: [    0.325968] clocksource: Switched to clocksource MIPS
Thu Jun 27 12:19:01 2019 kern.info kernel: [    0.339590] NET: Registered protocol family 2
Thu Jun 27 12:19:01 2019 kern.info kernel: [    0.350800] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
Thu Jun 27 12:19:01 2019 kern.info kernel: [    0.364807] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
Thu Jun 27 12:19:01 2019 kern.info kernel: [    0.377536] TCP: Hash tables configured (established 1024 bind 1024)
Thu Jun 27 12:19:01 2019 kern.info kernel: [    0.390676] UDP hash table entries: 256 (order: 0, 4096 bytes)
Thu Jun 27 12:19:01 2019 kern.info kernel: [    0.402450] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
Thu Jun 27 12:19:01 2019 kern.info kernel: [    0.415694] NET: Registered protocol family 1
Thu Jun 27 12:19:01 2019 kern.info kernel: [    0.434160] rt-timer 10000100.timer: maximum frequency is 3255Hz
Thu Jun 27 12:19:01 2019 kern.warn kernel: [    0.448814] Crashlog allocated RAM at address 0x1f00000
Thu Jun 27 12:19:01 2019 kern.info kernel: [    0.465905] workingset: timestamp_bits=30 max_order=13 bucket_order=0
Thu Jun 27 12:19:01 2019 kern.info kernel: [    0.495414] squashfs: version 4.0 (2009/01/31) Phillip Lougher
Thu Jun 27 12:19:01 2019 kern.info kernel: [    0.507095] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
Thu Jun 27 12:19:01 2019 kern.info kernel: [    0.568216] io scheduler noop registered
Thu Jun 27 12:19:01 2019 kern.info kernel: [    0.575915] io scheduler deadline registered (default)
Thu Jun 27 12:19:01 2019 kern.info kernel: [    0.587719] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
Thu Jun 27 12:19:01 2019 kern.info kernel: [    0.609517] console [ttyS0] disabled
Thu Jun 27 12:19:01 2019 kern.info kernel: [    0.616788] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 6666666) is a Palmchip BK-3103
Thu Jun 27 12:19:01 2019 kern.info kernel: [    0.636648] console [ttyS0] enabled
Thu Jun 27 12:19:01 2019 kern.info kernel: [    0.650659] bootconsole [early0] disabled
Thu Jun 27 12:19:01 2019 kern.err kernel: [    0.667925] cacheinfo: Failed to find cpu0 device node
Thu Jun 27 12:19:01 2019 kern.warn kernel: [    0.678472] cacheinfo: Unable to detect cache hierarchy for CPU 0
Thu Jun 27 12:19:01 2019 kern.info kernel: [    0.692613] 1f000000.cfi: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x001a00
Thu Jun 27 12:19:01 2019 kern.debug kernel: [    0.713003] 1f000000.cfi: Found an alias at 0x400000 for the chip at 0x0
Thu Jun 27 12:19:01 2019 kern.info kernel: [    0.713044] Amd/Fujitsu Extended Query Table at 0x0040
Thu Jun 27 12:19:01 2019 kern.info kernel: [    0.723567]   Amd/Fujitsu Extended Query version 1.3.
Thu Jun 27 12:19:01 2019 kern.notice kernel: [    0.733912] number of CFI chips: 1
Thu Jun 27 12:19:01 2019 kern.notice kernel: [    0.763510] 4 fixed-partitions partitions found on MTD device 1f000000.cfi
Thu Jun 27 12:19:01 2019 kern.notice kernel: [    0.777571] Creating 4 MTD partitions on "1f000000.cfi":
Thu Jun 27 12:19:01 2019 kern.notice kernel: [    0.788486] 0x000000000000-0x000000030000 : "u-boot"
Thu Jun 27 12:19:01 2019 kern.notice kernel: [    0.801096] 0x000000030000-0x000000040000 : "devdata"
Thu Jun 27 12:19:01 2019 kern.notice kernel: [    0.813979] 0x000000040000-0x000000050000 : "devconf"
Thu Jun 27 12:19:01 2019 kern.notice kernel: [    0.827051] 0x000000050000-0x000000400000 : "firmware"
Thu Jun 27 12:19:01 2019 kern.notice kernel: [    0.852725] 2 uimage-fw partitions found on MTD device firmware
Thu Jun 27 12:19:01 2019 kern.notice kernel: [    0.864919] 0x000000050000-0x0000001a19cd : "kernel"
Thu Jun 27 12:19:01 2019 kern.notice kernel: [    0.877670] 0x0000001a19cd-0x000000400000 : "rootfs"
Thu Jun 27 12:19:01 2019 kern.notice kernel: [    0.890239] mtd: device 5 (rootfs) set to be root filesystem
Thu Jun 27 12:19:01 2019 kern.notice kernel: [    0.901904] 1 squashfs-split partitions found on MTD device rootfs
Thu Jun 27 12:19:01 2019 kern.notice kernel: [    0.914588] 0x0000003c0000-0x000000400000 : "rootfs_data"
Thu Jun 27 12:19:01 2019 kern.info kernel: [    0.929929] libphy: Fixed MDIO Bus: probed
Thu Jun 27 12:19:01 2019 kern.info kernel: [    0.941883] rt3050-esw 10110000.esw: link changed 0x00
Thu Jun 27 12:19:01 2019 kern.info kernel: [    0.968999] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
Thu Jun 27 12:19:01 2019 kern.info kernel: [    0.987304] rt2880_wdt 10000120.watchdog: Initialized
Thu Jun 27 12:19:01 2019 kern.info kernel: [    1.001118] NET: Registered protocol family 10
Thu Jun 27 12:19:01 2019 kern.info kernel: [    1.023475] Segment Routing with IPv6
Thu Jun 27 12:19:01 2019 kern.info kernel: [    1.031295] NET: Registered protocol family 17
Thu Jun 27 12:19:01 2019 kern.info kernel: [    1.040591] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
Thu Jun 27 12:19:01 2019 kern.info kernel: [    1.066901] 8021q: 802.1Q VLAN Support v1.8
Thu Jun 27 12:19:01 2019 kern.info kernel: [    1.090328] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
Thu Jun 27 12:19:01 2019 kern.info kernel: [    1.107082] Freeing unused kernel memory: 152K
Thu Jun 27 12:19:01 2019 kern.warn kernel: [    1.116215] This architecture does not have kernel memory protection.
Thu Jun 27 12:19:01 2019 user.info kernel: [    2.121392] init: Console is alive
Thu Jun 27 12:19:01 2019 user.info kernel: [    2.129218] init: - watchdog -
Thu Jun 27 12:19:01 2019 kern.notice kernel: [    2.586054] random: fast init done
Thu Jun 27 12:19:01 2019 kern.info kernel: [    2.672827] rt3050-esw 10110000.esw: link changed 0x08
Thu Jun 27 12:19:01 2019 user.info kernel: [    3.310116] kmodloader: loading kernel modules from /etc/modules-boot.d/*
Thu Jun 27 12:19:01 2019 user.info kernel: [    3.473617] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
Thu Jun 27 12:19:01 2019 user.info kernel: [    3.499523] init: - preinit -
Thu Jun 27 12:19:01 2019 kern.info kernel: [    4.744023] 8021q: adding VLAN 0 to HW filter on device eth0
Thu Jun 27 12:19:01 2019 kern.notice kernel: [    4.807593] random: procd: uninitialized urandom read (4 bytes read)
Thu Jun 27 12:19:01 2019 user.notice kernel: [    8.389257] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
Thu Jun 27 12:19:01 2019 user.warn kernel: [    8.461892] urandom-seed: Seed file not found (/etc/urandom.seed)
Thu Jun 27 12:19:01 2019 user.info kernel: [    8.691867] procd: - early -
Thu Jun 27 12:19:01 2019 user.info kernel: [    8.698345] procd: - watchdog -
Thu Jun 27 12:19:01 2019 user.info kernel: [    9.542956] procd: - watchdog -
Thu Jun 27 12:19:01 2019 user.info kernel: [    9.550705] procd: - ubus -
Thu Jun 27 12:19:01 2019 kern.notice kernel: [    9.718507] random: ubusd: uninitialized urandom read (4 bytes read)
Thu Jun 27 12:19:01 2019 kern.notice kernel: [    9.863957] random: ubusd: uninitialized urandom read (4 bytes read)
Thu Jun 27 12:19:01 2019 kern.notice kernel: [    9.878290] random: ubusd: uninitialized urandom read (4 bytes read)
Thu Jun 27 12:19:01 2019 user.info kernel: [    9.896376] procd: - init -
Thu Jun 27 12:19:01 2019 user.info kernel: [   10.626635] kmodloader: loading kernel modules from /etc/modules.d/*
Thu Jun 27 12:19:01 2019 kern.info kernel: [   10.654495] ip6_tables: (C) 2000-2006 Netfilter Core Team
Thu Jun 27 12:19:01 2019 kern.info kernel: [   10.696121] Loading modules backported from Linux version wt-2017-11-01-0-gfe248fc2c180
Thu Jun 27 12:19:01 2019 kern.info kernel: [   10.712420] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d
Thu Jun 27 12:19:01 2019 kern.info kernel: [   10.736149] ip_tables: (C) 2000-2006 Netfilter Core Team
Thu Jun 27 12:19:01 2019 kern.info kernel: [   10.767787] nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
Thu Jun 27 12:19:01 2019 kern.info kernel: [   10.925396] xt_time: kernel timezone is -0000
Thu Jun 27 12:19:01 2019 kern.info kernel: [   11.050512] PPP generic driver version 2.4.2
Thu Jun 27 12:19:01 2019 kern.info kernel: [   11.066924] NET: Registered protocol family 24
Thu Jun 27 12:19:01 2019 kern.info kernel: [   11.128843] rt2800_wmac 10180000.wmac: loaded eeprom from mtd device "devdata"
Thu Jun 27 12:19:01 2019 kern.info kernel: [   11.143671] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 2872, rev 0200 detected
Thu Jun 27 12:19:01 2019 kern.info kernel: [   11.159505] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 0005 detected
Thu Jun 27 12:19:01 2019 kern.debug kernel: [   11.175056] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
Thu Jun 27 12:19:01 2019 user.info kernel: [   11.349828] kmodloader: done loading kernel modules from /etc/modules.d/*
Thu Jun 27 12:19:01 2019 kern.warn kernel: [   13.056965] urandom_read: 5 callbacks suppressed
Thu Jun 27 12:19:01 2019 kern.notice kernel: [   13.056986] random: jshn: uninitialized urandom read (4 bytes read)
Thu Jun 27 12:19:03 2019 user.notice dnsmasq: DNS rebinding protection is active, will discard upstream RFC1918 responses!
Thu Jun 27 12:19:03 2019 user.notice dnsmasq: Allowing 127.0.0.0/8 responses
Thu Jun 27 12:19:04 2019 daemon.info dnsmasq[801]: started, version 2.80 cachesize 150
Thu Jun 27 12:19:04 2019 daemon.info dnsmasq[801]: DNS service limited to local subnets
Thu Jun 27 12:19:04 2019 daemon.info dnsmasq[801]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth no-DNSSEC no-ID loop-detect inotify dumpfile
Thu Jun 27 12:19:04 2019 daemon.info dnsmasq[801]: using local addresses only for domain test
Thu Jun 27 12:19:04 2019 daemon.info dnsmasq[801]: using local addresses only for domain onion
Thu Jun 27 12:19:04 2019 daemon.info dnsmasq[801]: using local addresses only for domain localhost
Thu Jun 27 12:19:04 2019 daemon.info dnsmasq[801]: using local addresses only for domain local
Thu Jun 27 12:19:04 2019 daemon.info dnsmasq[801]: using local addresses only for domain invalid
Thu Jun 27 12:19:04 2019 daemon.info dnsmasq[801]: using local addresses only for domain bind
Thu Jun 27 12:19:04 2019 daemon.info dnsmasq[801]: using local addresses only for domain lan
Thu Jun 27 12:19:04 2019 daemon.warn dnsmasq[801]: no servers found in /tmp/resolv.conf.auto, will retry
Thu Jun 27 12:19:04 2019 daemon.info dnsmasq[801]: read /etc/hosts - 4 addresses
Thu Jun 27 12:19:04 2019 daemon.info dnsmasq[801]: read /tmp/hosts/dhcp.cfg01411c - 0 addresses
Thu Jun 27 12:19:10 2019 user.notice : Added device handler type: tunnel
Thu Jun 27 12:19:10 2019 user.notice : Added device handler type: Network device
Thu Jun 27 12:19:10 2019 user.notice : Added device handler type: bridge
Thu Jun 27 12:19:10 2019 user.notice : Added device handler type: veth
Thu Jun 27 12:19:10 2019 user.notice : Added device handler type: macvlan
Thu Jun 27 12:19:10 2019 user.notice : Added device handler type: 8021ad
Thu Jun 27 12:19:10 2019 user.notice : Added device handler type: 8021q
Thu Jun 27 12:19:11 2019 daemon.notice procd: /etc/init.d/network: 'radio0' is disabled
Thu Jun 27 12:19:11 2019 daemon.notice procd: /etc/init.d/network: 'radio0' is disabled
Thu Jun 27 12:19:18 2019 user.notice ucitrack: Setting up /etc/config/network reload dependency on /etc/config/dhcp
Thu Jun 27 12:19:18 2019 user.notice ucitrack: Setting up /etc/config/network reload dependency on /etc/config/radvd
Thu Jun 27 12:19:18 2019 user.notice ucitrack: Setting up /etc/config/wireless reload dependency on /etc/config/network
Thu Jun 27 12:19:19 2019 user.notice ucitrack: Setting up /etc/config/firewall reload dependency on /etc/config/luci-splash
Thu Jun 27 12:19:19 2019 user.notice ucitrack: Setting up /etc/config/firewall reload dependency on /etc/config/qos
Thu Jun 27 12:19:19 2019 user.notice ucitrack: Setting up /etc/config/firewall reload dependency on /etc/config/miniupnpd
Thu Jun 27 12:19:20 2019 user.notice ucitrack: Setting up /etc/config/dhcp reload dependency on /etc/config/odhcpd
Thu Jun 27 12:19:22 2019 user.notice ucitrack: Setting up non-init /etc/config/fstab reload handler: /sbin/block mount
Thu Jun 27 12:19:22 2019 user.notice ucitrack: Setting up /etc/config/system reload trigger for non-procd /etc/init.d/led
Thu Jun 27 12:19:23 2019 user.notice ucitrack: Setting up /etc/config/system reload dependency on /etc/config/luci_statistics
Thu Jun 27 12:19:23 2019 user.notice ucitrack: Setting up /etc/config/system reload dependency on /etc/config/dhcp
Thu Jun 27 12:19:25 2019 kern.err kernel: [   44.315763] jffs2: Too few erase blocks (4)
Thu Jun 27 12:19:25 2019 daemon.err mount_root: failed - mount -t jffs2 /dev/mtdblock6 /rom/overlay: Invalid argument
Thu Jun 27 12:19:27 2019 daemon.notice procd: /etc/rc.d/S96led: setting up led WAN LED (amber)
Thu Jun 27 12:19:28 2019 kern.info kernel: [   46.657999] 8021q: adding VLAN 0 to HW filter on device eth0
Thu Jun 27 12:19:28 2019 kern.info kernel: [   46.761430] br-lan: port 1(eth0.1) entered blocking state
Thu Jun 27 12:19:28 2019 kern.info kernel: [   46.772519] br-lan: port 1(eth0.1) entered disabled state
Thu Jun 27 12:19:28 2019 kern.info kernel: [   46.784464] device eth0.1 entered promiscuous mode
Thu Jun 27 12:19:28 2019 kern.info kernel: [   46.794338] device eth0 entered promiscuous mode
Thu Jun 27 12:19:28 2019 kern.info kernel: [   46.991682] br-lan: port 1(eth0.1) entered blocking state
Thu Jun 27 12:19:28 2019 kern.info kernel: [   47.002761] br-lan: port 1(eth0.1) entered forwarding state
Thu Jun 27 12:19:28 2019 kern.info kernel: [   47.014766] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
Thu Jun 27 12:19:28 2019 daemon.notice netifd: Interface 'lan' is enabled
Thu Jun 27 12:19:28 2019 daemon.notice netifd: Interface 'lan' is setting up now
Thu Jun 27 12:19:28 2019 daemon.notice netifd: Interface 'lan' is now up
Thu Jun 27 12:19:28 2019 daemon.notice netifd: Interface 'loopback' is enabled
Thu Jun 27 12:19:28 2019 daemon.notice netifd: Interface 'loopback' is setting up now
Thu Jun 27 12:19:28 2019 daemon.notice netifd: Interface 'loopback' is now up
Thu Jun 27 12:19:28 2019 daemon.notice netifd: Interface 'wan' is enabled
Thu Jun 27 12:19:28 2019 daemon.notice netifd: Interface 'wan6' is enabled
Thu Jun 27 12:19:28 2019 daemon.notice netifd: bridge 'br-lan' link is up
Thu Jun 27 12:19:28 2019 daemon.notice netifd: Interface 'lan' has link connectivity
Thu Jun 27 12:19:28 2019 daemon.notice netifd: Network device 'eth0' link is up
Thu Jun 27 12:19:28 2019 daemon.notice netifd: VLAN 'eth0.1' link is up
Thu Jun 27 12:19:29 2019 daemon.notice netifd: Network device 'lo' link is up
Thu Jun 27 12:19:29 2019 daemon.notice netifd: Interface 'loopback' has link connectivity
Thu Jun 27 12:19:29 2019 daemon.notice netifd: VLAN 'eth0.2' link is up
Thu Jun 27 12:19:29 2019 daemon.notice netifd: Interface 'wan' has link connectivity
Thu Jun 27 12:19:29 2019 daemon.notice netifd: Interface 'wan' is setting up now
Thu Jun 27 12:19:29 2019 daemon.notice netifd: Interface 'wan6' has link connectivity
Thu Jun 27 12:19:29 2019 daemon.notice netifd: Interface 'wan6' is setting up now
Thu Jun 27 12:19:29 2019 kern.info kernel: [   47.656594] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
Thu Jun 27 12:19:30 2019 daemon.notice netifd: wan (1178): udhcpc: started, v1.28.4
Thu Jun 27 12:19:31 2019 user.notice firewall: Reloading firewall due to ifup of lan (br-lan)
Thu Jun 27 12:19:32 2019 daemon.notice netifd: wan (1178): udhcpc: sending discover
Thu Jun 27 12:19:34 2019 daemon.info procd: - init complete -
Thu Jun 27 12:19:35 2019 daemon.notice netifd: wan (1178): udhcpc: sending discover
Thu Jun 27 12:19:38 2019 daemon.notice netifd: wan (1178): udhcpc: sending discover
Thu Jun 27 12:19:40 2019 daemon.info dnsmasq[801]: exiting on receipt of SIGTERM
Thu Jun 27 12:19:40 2019 daemon.info dnsmasq[1322]: started, version 2.80 cachesize 150
Thu Jun 27 12:19:40 2019 daemon.info dnsmasq[1322]: DNS service limited to local subnets
Thu Jun 27 12:19:40 2019 daemon.info dnsmasq[1322]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth no-DNSSEC no-ID loop-detect inotify dumpfile
Thu Jun 27 12:19:40 2019 daemon.info dnsmasq-dhcp[1322]: DHCP, IP range 192.168.1.100 -- 192.168.1.249, lease time 12h
Thu Jun 27 12:19:40 2019 daemon.info dnsmasq[1322]: using local addresses only for domain test
Thu Jun 27 12:19:40 2019 daemon.info dnsmasq[1322]: using local addresses only for domain onion
Thu Jun 27 12:19:40 2019 daemon.info dnsmasq[1322]: using local addresses only for domain localhost
Thu Jun 27 12:19:40 2019 daemon.info dnsmasq[1322]: using local addresses only for domain local
Thu Jun 27 12:19:40 2019 daemon.info dnsmasq[1322]: using local addresses only for domain invalid
Thu Jun 27 12:19:40 2019 daemon.info dnsmasq[1322]: using local addresses only for domain bind
Thu Jun 27 12:19:40 2019 daemon.info dnsmasq[1322]: using local addresses only for domain lan
Thu Jun 27 12:19:40 2019 daemon.warn dnsmasq[1322]: no servers found in /tmp/resolv.conf.auto, will retry
Thu Jun 27 12:19:40 2019 daemon.info dnsmasq[1322]: read /etc/hosts - 4 addresses
Thu Jun 27 12:19:40 2019 daemon.info dnsmasq[1322]: read /tmp/hosts/dhcp.cfg01411c - 1 addresses
Thu Jun 27 12:19:40 2019 daemon.info dnsmasq-dhcp[1322]: read /etc/ethers - 0 addresses
Thu Jun 27 12:19:40 2019 daemon.info dnsmasq[1322]: read /etc/hosts - 4 addresses
Thu Jun 27 12:19:40 2019 daemon.info dnsmasq[1322]: read /tmp/hosts/dhcp.cfg01411c - 1 addresses
Thu Jun 27 12:19:40 2019 daemon.info dnsmasq-dhcp[1322]: read /etc/ethers - 0 addresses
Thu Jun 27 12:19:47 2019 daemon.info dnsmasq-dhcp[1322]: DHCPDISCOVER(br-lan) 00:0e:c6:8e:2b:c9
Thu Jun 27 12:19:47 2019 daemon.info dnsmasq-dhcp[1322]: DHCPOFFER(br-lan) 192.168.1.122 00:0e:c6:8e:2b:c9
Thu Jun 27 12:19:48 2019 daemon.info dnsmasq-dhcp[1322]: DHCPREQUEST(br-lan) 192.168.1.122 00:0e:c6:8e:2b:c9
Thu Jun 27 12:19:48 2019 daemon.info dnsmasq-dhcp[1322]: DHCPACK(br-lan) 192.168.1.122 00:0e:c6:8e:2b:c9 badapple
Thu Jun 27 12:20:09 2019 daemon.err uhttpd[958]: luci: accepted login on /admin for root from 192.168.1.122
Thu Jun 27 12:20:34 2019 kern.notice kernel: [  112.796216] random: crng init done
Thu Jun 27 12:20:34 2019 daemon.info urandom_seed[1268]: Seed saved (/etc/urandom.seed)
Thu Jun 27 12:20:56 2019 auth.err passwd: password for root changed by root
Thu Jun 27 12:21:36 2019 auth.err passwd: password for root changed by root
24.08.20192462Base systemBug ReportVery LowHighwrt32x WIFI was breaking on 2 sec I did not get full co...AllUnconfirmed Task Description

Supply the following if possible:
- Device problem occurs on wrt32x
- Software versions of OpenWrt 19.07

I tested these images on wrt32x and wrt3600, but unfortunately I gave up there was a problem on wrt32x WIFI was breaking the computer and in the relayd wrt3600 → wrt32x the maximum speed on the bridge is 10Mb. I do not observe this for version 18.06 (images downloaded from eko.one.pl). And after disconnection I did not get full connection speed of 866.7 Mb / s to the router. Although I will say that options 19.07 in Lucia look encouraging.

15.09.20192496Base systemBug ReportVery LowHighWPA3-SAE can't be enabled on mt76 deviceTrunkUnconfirmed Task Description

Device: Netgear EX2700

Version: OpenWrt 19.07-SNAPSHOT r10532-cf3b50377e / LuCI openwrt-19.07 branch (git-19.256.45060-8a2f1c7)

Steps to reproduce: Enable WPA3 or WPA3-Mixed Mode via LuCI.

Result:
Wifi won’t come up. Works fine with WPA2.

Sun Sep 15 20:08:18 2019 kern.info kernel: [ 1638.740004] device wlan0 left promiscuous mode
Sun Sep 15 20:08:18 2019 kern.info kernel: [ 1638.740123] br-lan: port 2(wlan0) entered disabled state
Sun Sep 15 20:08:18 2019 daemon.notice hostapd: wlan0: interface state ENABLED->DISABLED
Sun Sep 15 20:08:18 2019 daemon.notice hostapd: wlan0-1: AP-DISABLED
Sun Sep 15 20:08:18 2019 daemon.notice hostapd: wlan0-1: CTRL-EVENT-TERMINATING
Sun Sep 15 20:08:18 2019 daemon.notice netifd: Network device 'wlan0-1' link is down
Sun Sep 15 20:08:19 2019 kern.info kernel: [ 1639.020561] br-guest: port 2(wlan0-1) entered disabled state
Sun Sep 15 20:08:19 2019 kern.info kernel: [ 1639.023338] device wlan0-1 left promiscuous mode
Sun Sep 15 20:08:19 2019 kern.info kernel: [ 1639.023357] br-guest: port 2(wlan0-1) entered disabled state
Sun Sep 15 20:08:19 2019 daemon.notice hostapd: nl80211: Failed to remove interface wlan0-1 from bridge br-guest: No such device
Sun Sep 15 20:08:19 2019 daemon.notice hostapd: wlan0: AP-DISABLED
Sun Sep 15 20:08:19 2019 daemon.notice hostapd: wlan0: CTRL-EVENT-TERMINATING
Sun Sep 15 20:08:19 2019 daemon.notice hostapd: nl80211: deinit ifname=wlan0 disabled_11b_rates=0
Sun Sep 15 20:08:19 2019 daemon.notice hostapd: nl80211: Failed to remove interface wlan0 from bridge br-lan: Invalid argument
Sun Sep 15 20:08:19 2019 user.notice mac80211: Failed command: iw phy phy0 set antenna 0xffffffff 0xffffffff
Sun Sep 15 20:08:19 2019 daemon.notice netifd: radio0 (1867): command failed: Not supported (-122)
Sun Sep 15 20:08:19 2019 user.notice mac80211: Failed command: iw phy phy0 set distance 0
Sun Sep 15 20:08:19 2019 daemon.err hostapd: Configuration file: /var/run/hostapd-phy0.conf
Sun Sep 15 20:08:21 2019 kern.info kernel: [ 1639.912716] ieee80211 phy0: rt2800_rf_self_txdc_cal: Info - RF Tx self calibration start
Sun Sep 15 20:08:21 2019 kern.info kernel: [ 1639.913245] ieee80211 phy0: rt2800_rf_self_txdc_cal: Info - RF Tx self calibration end
Sun Sep 15 20:08:22 2019 kern.info kernel: [ 1641.824164] ieee80211 phy0: rt2800_loft_iq_calibration: Info - LOFT Calibration Done!
Sun Sep 15 20:08:22 2019 kern.info kernel: [ 1641.828164] ieee80211 phy0: rt2800_iq_search: Info - IQCalibration Start!
Sun Sep 15 20:08:22 2019 kern.info kernel: [ 1641.842569] ieee80211 phy0: rt2800_iq_search: Info - IQCalibration Done! CH = 0, (gain= 0, phase=3f)
Sun Sep 15 20:08:22 2019 kern.info kernel: [ 1641.843488] ieee80211 phy0: rt2800_iq_search: Info - IQCalibration Start!
Sun Sep 15 20:08:22 2019 kern.info kernel: [ 1641.857895] ieee80211 phy0: rt2800_iq_search: Info - IQCalibration Done! CH = 1, (gain= 0, phase= 2)
Sun Sep 15 20:08:22 2019 kern.info kernel: [ 1641.857931] ieee80211 phy0: rt2800_loft_iq_calibration: Info - TX IQ Calibration Done!
Sun Sep 15 20:08:22 2019 kern.info kernel: [ 1641.871433] ieee80211 phy0: rt2800_rxiq_calibration: Info - RXIQ G_imb=1, Ph_rx=-6
Sun Sep 15 20:08:22 2019 kern.info kernel: [ 1641.881694] ieee80211 phy0: rt2800_rxiq_calibration: Info - RXIQ G_imb=0, Ph_rx=2
Sun Sep 15 20:08:22 2019 kern.info kernel: [ 1641.888849] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
Sun Sep 15 20:08:22 2019 kern.info kernel: [ 1641.894441] br-lan: port 2(wlan0) entered blocking state
Sun Sep 15 20:08:22 2019 kern.info kernel: [ 1641.894456] br-lan: port 2(wlan0) entered disabled state
Sun Sep 15 20:08:22 2019 kern.info kernel: [ 1641.894799] device wlan0 entered promiscuous mode
Sun Sep 15 20:08:22 2019 daemon.notice hostapd: wlan0: interface state UNINITIALIZED->COUNTRY_UPDATE
Sun Sep 15 20:08:22 2019 daemon.err hostapd: Using interface wlan0 with hwaddr XX:XX:XX:XX:XX:XX and ssid "HOME"
Sun Sep 15 20:08:22 2019 daemon.err hostapd: Interface initialization failed
Sun Sep 15 20:08:22 2019 daemon.notice hostapd: wlan0: interface state COUNTRY_UPDATE->DISABLED
Sun Sep 15 20:08:22 2019 kern.info kernel: [ 1641.994731] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
Sun Sep 15 20:08:22 2019 kern.info kernel: [ 1641.994904] br-lan: port 2(wlan0) entered blocking state
Sun Sep 15 20:08:22 2019 kern.info kernel: [ 1641.994914] br-lan: port 2(wlan0) entered forwarding state
Sun Sep 15 20:08:22 2019 daemon.notice hostapd: wlan0: AP-DISABLED
Sun Sep 15 20:08:22 2019 daemon.err hostapd: wlan0: Unable to setup interface.
Sun Sep 15 20:08:22 2019 daemon.notice hostapd: wlan0: interface state DISABLED->DISABLED
Sun Sep 15 20:08:22 2019 daemon.notice hostapd: wlan0-1: AP-DISABLED
Sun Sep 15 20:08:22 2019 daemon.notice hostapd: wlan0-1: CTRL-EVENT-TERMINATING
Sun Sep 15 20:08:22 2019 daemon.err hostapd: hostapd_free_hapd_data: Interface wlan0-1 wasn't started
Sun Sep 15 20:08:22 2019 daemon.notice hostapd: wlan0: AP-DISABLED
Sun Sep 15 20:08:22 2019 daemon.notice hostapd: wlan0: CTRL-EVENT-TERMINATING
Sun Sep 15 20:08:22 2019 daemon.err hostapd: hostapd_free_hapd_data: Interface wlan0 wasn't started
Sun Sep 15 20:08:22 2019 daemon.notice hostapd: nl80211: deinit ifname=wlan0 disabled_11b_rates=0
Sun Sep 15 20:08:22 2019 kern.info kernel: [ 1642.002616] device wlan0 left promiscuous mode
Sun Sep 15 20:08:22 2019 kern.info kernel: [ 1642.002723] br-lan: port 2(wlan0) entered disabled state
Sun Sep 15 20:08:22 2019 daemon.notice hostapd: ELOOP: remaining socket: sock=22 eloop_data=0x77d76c60 user_data=0 handler=0x46a4f5
Sun Sep 15 20:08:22 2019 daemon.notice netifd: radio0 (1867): WARNING (wireless_add_process): executable path /usr/sbin/wpad does not match process 1120 path ()
Sun Sep 15 20:08:22 2019 daemon.notice netifd: radio0 (1867): Device setup failed: HOSTAPD_START_FAILED


10.10.20192543Base systemBug ReportVery LowHighCloud Engines Pogoplug V4 USB3 Does Not Workopenwrt-18.06Unconfirmed Task Description

In the configuration added

define Device/cloudengines_pogoplugv4

DEVICE_TITLE := Cloud Engines Pogoplug V4
DEVICE_DTS := kirkwood-pogoplug-series-4
DEVICE_PACKAGES := kmod-usb3

endef
TARGET_DEVICES += cloudengines_pogoplugv4

But kmod-usb3 has built and included. I need to enabled CONFIG_PACKAGE_kmod-usb3=y which also enables CONFIG_PACKAGE_kmod-usb-core=y as dependency the USB3 is working. This is build issue.

11.11.20192591Base systemBug ReportVery LowHighInternet drop out on LAN wget YouTube on Fritz!Box 4040TrunkUnconfirmed Task Description

Recently I’ve upgraded from a Buffalo WZR-HP-AG300H to a Fritz!Box 4040. My download speed doubled on my 400Mbit cable connection but since then I do experience as well a lot of instabilities where my previous setup was 100% stable. The OpenWrt router runs behind a DS-lite cable router (Fritz!Box 6591).

Just by watching a YouTube video (e.g. music) or by downloading with wget some files (e.g. Linux Iso images) via the LAN interface, OpenWrt on the Fritz!Box 4040 will randomly drop the internet connection completely. It disconnects the router, no ping with IPv4 or IPv6 is possible then anymore from my machine. Strangely I can access the web interface only via Wifi to reboot the router. The lost connection doesn’t come back after some time, the router requires a reboot.

If I avoid YouTube/wget, the OpenWrt router runs quite well when just doing normal internet browsing and running a web server behind the OpenWrt router.

In the log files I do not see any special hint what might cause the drop outs. I’ve tested multiple different setups already, ordered a second Fritz!Box 4040 to exclude a hardware issue, tested with 2 different cable routers, did a factory reset, flashed the latest OpenWrt snapshot (plus added luci) and used the standard configs, nothing seems to help. I assume that it is related somehow to IPv6. There are other users with the Fritz!Box 4040 that do not experience these issues, but they use it only with IPv4. As I have DS-lite, I need to use IPv6 to avoid the 6to4 tunneling on the cable router.

- Fritz!Box 4040
- OpenWrt 18.06.4 + Dev Snapshot 2019-11-10
- IPv4 and IPv6 incl. Prefix delegation to LAN interface
- Watch YouTube videos or download files with wget

For reference, I did a post on the forum: https://forum.openwrt.org/t/fritz-box-4040-drops-out-internet-connection-if-watching-youtube-from-lan/46753

12.11.20192593Base systemBug ReportVery LowHighno AC wifi with ath10k on 19.07-rc1openwrt-19.07Waiting on reporter Task Description

- Archer C7, Netgear R7800
- 19.07-RC1 default
- install image, configure wifi, try to connect, in my case i’m getting 300Mbps rate, others report as low as up to 54 (legacy only)

 

R7800 report: https://forum.openwrt.org/t/openwrt-19-07-0-first-release-candidate/48040/33

Archer C7 v2 report: https://forum.openwrt.org/t/openwrt-19-07-rc1-archer-c7-v2-5g-wifi-died-after-trying-to-change-channels/48182/7

the situation is the same with intree 4.9.200 driver or any of the latest backports installed on client PC

28.11.20192637Base systemBug ReportHighHighhostapd ubus reload makes OpenWrt as WiFi client very u...TrunkNew Task Description

Commit 60fb4c92b6b0d1582d31e02167b90b424185f3a2 (hostapd: add ubus reload) breaks WiFi client connectivity when for some reason the association does not succeed immediately.

I started seeing this problem on all my Raspberry Pi Zero W devices, where WiFi takes a long time to come up due to the lack of entropy:

[   32.392170] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[  104.672670] random: crng init done
[  104.685751] random: 3 urandom warning(s) missed due to ratelimiting
[  105.436537] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready

At this point, the Raspberry Pi is associated to the AP, but the DHCP client is not running. This is the output of ifstatus lan:

{
        "up": false,
        "pending": false,
        "available": false,
        "autostart": true,
        "dynamic": false,
        "proto": "dhcp",
        "data": {

        },
        "errors": [
                {
                        "subsystem": "interface",
                        "code": "NO_DEVICE"
                }
        ]
}

Running ifup lan fixes the problem, but this is of course not easy to do on headless devices.

Later I also experienced this problem on a Raspberry Pi 3 A, which does not have the low entropy problem. In this case the delayed association was caused by a power outage, and the Raspberry Pi booted faster than the APs.

30.11.20192643Base systemBug ReportVery LowHighEspressoBin: Internal error: synchronous parity or ECC ...TrunkUnconfirmed Task Description

Supply the following if possible:
- Device problem occurs on

Hardware name: Globalscale Marvell ESPRESSOBin Board (DT)

- Software versions of OpenWrt/LEDE release, packages, etc.

11595-g5d2a900163

- Steps to reproduce

Boot and wait about an hour. Here are a series of kernel panics:

[ 4228.773060] Internal error: synchronous parity or ECC error: 86000018 [#1] SMP
[ 4228.777653] Modules linked in: ath9k ath9k_common xt_connlimit nf_conncount iptable_nat ipt_MASQUERADE ath9k_hw ath xt_state xt_nat xt_helper xt_conntrack xt_connmark xt_connbytes xt_REDIRECT xt_NETMAP xt_FLOWOFFLOAD xt_CT 
nf_nat_ipv4 nf_nat nf_flow_table_hw nf_flow_table nf_conntrack_rtcache nf_conntrack mac80211 ipt_REJECT cfg80211 xt_time xt_tcpudp xt_tcpmss xt_string xt_statistic xt_recent xt_quota xt_pkttype xt_owner xt_multiport xt_mark xt
_mac xt_limit xt_length xt_hl xt_ecn xt_dscp xt_condition xt_comment xt_bpf xt_addrtype xt_TCPMSS xt_LOG xt_HL xt_DSCP xt_CLASSIFY ts_kmp ts_fsm ts_bm nf_reject_ipv4 nf_log_ipv4 nf_defrag_ipv6 nf_defrag_ipv4 iptable_raw iptabl
e_mangle iptable_filter ipt_ECN ip_tables compat nf_log_ipv6 nf_log_common ip6table_mangle ip6table_filter ip6_tables ip6t_REJECT x_tables
[ 4228.850958]  nf_reject_ipv6 tun gpio_button_hotplug
[ 4228.855992] Process kworker/1:2 (pid: 594, stack limit = 0x00000000a141aece)
[ 4228.863262] CPU: 1 PID: 594 Comm: kworker/1:2 Not tainted 4.19.85 #0
[ 4228.869776] Hardware name: Globalscale Marvell ESPRESSOBin Board (DT)
[ 4228.876450] Workqueue:            (null) (events)
[ 4228.881258] pstate: 80400085 (Nzcv daIf +PAN -UAO)
[ 4228.886204] pc : kthread_data+0x8/0x40
[ 4228.890035] lr : wq_worker_sleeping+0xc/0xb0
[ 4228.894410] sp : ffffff8009463d60
[ 4228.897819] x29: ffffff8009463d60 x28: 0000000000000000 
[ 4228.903281] x27: 0000000000000000 x26: ffffff80080b5318 
[ 4228.908746] x25: 0000000000000000 x24: ffffffc03e479a18 
[ 4228.914213] x23: ffffff8008868738 x22: ffffff800884e018 
[ 4228.919678] x21: ffffff8008853500 x20: ffffffc03e479500 
[ 4228.925146] x19: ffffffc03ffdd500 x18: 0000000000000000 
[ 4228.930609] x17: 0000000000000000 x16: 0000000000000000 
[ 4228.936076] x15: 0000000000000000 x14: 0000000000000000 
[ 4228.941541] x13: 0000000000000002 x12: 0000000000000001 
[ 4228.947006] x11: ffffffc03ffd94d0 x10: 00000000000007c0 
[ 4228.952472] x9 : ffffffc03e13d668 x8 : ffffff80088a9b08 
[ 4228.957937] x7 : 0000000000000000 x6 : 00000000050ebc0a 
[ 4228.963404] x5 : 0000000000000004 x4 : 0000000000000002 
[ 4228.968869] x3 : 00000000fffffff9 x2 : 0000000800000000 
[ 4228.974335] x1 : 0000000000000001 x0 : ffffffc03e479500 
[ 4228.979797] Call trace:
[ 4228.982331]  kthread_data+0x8/0x40
[ 4228.985813]  wq_worker_sleeping+0xc/0xb0
[ 4228.989859]  __schedule+0x140/0x570
[ 4228.993436]  schedule+0x58/0x80
[ 4228.996656]  worker_thread+0x370/0x468
[ 4229.000513]  kthread+0x110/0x120
[ 4229.003829]  ret_from_fork+0x10/0x1c
[ 4229.007521] Code: d65f03c0 d503201f a9be7bfd 910003fd (f9000bf3) 
[ 4229.013769] ---[ end trace 4f1be3f746ce5030 ]---
[ 4229.024169] Kernel panic - not syncing: Fatal exception
[ 4229.026728] SMP: stopping secondary CPUs
[ 4229.030757] Kernel Offset: disabled
[ 4229.034342] CPU features: 0x0,00002008
[ 4229.038186] Memory Limit: none
[ 4229.044024] Rebooting in 3 seconds..
[ 3676.038431] Internal error: synchronous parity or ECC error: 86000018 [#1] SMP
[ 3676.043028] Modules linked in: ath9k ath9k_common xt_connlimit nf_conncount iptable_nat ipt_MASQUERADE ath9k_hw ath xt_state xt_nat xt_helper xt_conntrack xt_connmark xt_connbytes xt_REDIRECT xt_NETMAP xt_FLOWOFFLOAD xt_CT 
nf_nat_ipv4 nf_nat nf_flow_table_hw nf_flow_table nf_conntrack_rtcache nf_conntrack mac80211 ipt_REJECT cfg80211 xt_time xt_tcpudp xt_tcpmss xt_string xt_statistic xt_recent xt_quota xt_pkttype xt_owner xt_multiport xt_mark xt
_mac xt_limit xt_length xt_hl xt_ecn xt_dscp xt_condition xt_comment xt_bpf xt_addrtype xt_TCPMSS xt_LOG xt_HL xt_DSCP xt_CLASSIFY ts_kmp ts_fsm ts_bm nf_reject_ipv4 nf_log_ipv4 nf_defrag_ipv6 nf_defrag_ipv4 iptable_raw iptabl
e_mangle iptable_filter ipt_ECN ip_tables compat nf_log_ipv6 nf_log_common ip6table_mangle ip6table_filter ip6_tables ip6t_REJECT x_tables
[ 3676.116317]  nf_reject_ipv6 tun gpio_button_hotplug
[ 3676.121338] Process kworker/0:1 (pid: 41, stack limit = 0x000000008b9ea8ea)
[ 3676.128509] CPU: 0 PID: 41 Comm: kworker/0:1 Not tainted 4.19.85 #0
[ 3676.134953] Hardware name: Globalscale Marvell ESPRESSOBin Board (DT)
[ 3676.141596] Workqueue:            (null) (events)
[ 3676.146426] pstate: 60400085 (nZCv daIf +PAN -UAO)
[ 3676.151361] pc : update_cfs_group+0x0/0xb0
[ 3676.155565] lr : dequeue_task_fair+0x440/0x960
[ 3676.160130] sp : ffffff8008a23cf0
[ 3676.163535] x29: ffffff8008a23cf0 x28: ffffffc03ffcd500 
[ 3676.169001] x27: ffffffc0043a5e80 x26: ffffff80088523f0 
[ 3676.174466] x25: afb504000afb5041 x24: ffffff80088c85c0 
[ 3676.179932] x23: 00000357e4f6aec0 x22: ffffff800884e018 
[ 3676.185397] x21: 0000000000000009 x20: ffffffc0043a5f40 
[ 3676.190863] x19: ffffffc03ffcd580 x18: 0000000000000000 
[ 3676.196329] x17: 0000000000000000 x16: 0000000000000000 
[ 3676.201793] x15: 0000000000000000 x14: 0000000000000000 
[ 3676.207259] x13: 0000000000000000 x12: 0000000000000000 
[ 3676.212726] x11: 0000000000000000 x10: 00000000000007c0 
[ 3676.218191] x9 : ffffffc0042eea68 x8 : ffffff80088a9b08 
[ 3676.223657] x7 : 0000000000000001 x6 : 00000000050e6eea 
[ 3676.229122] x5 : 00000000000000e8 x4 : ffffffc0043a3ff0 
[ 3676.234587] x3 : ffffffc03ffcdef8 x2 : ffffffc0043a5f70 
[ 3676.240053] x1 : 0000000000000001 x0 : ffffffc0043a5f40 
[ 3676.245519] Call trace:
[ 3676.248032]  update_cfs_group+0x0/0xb0
[ 3676.251887]  deactivate_task+0x6c/0x80
[ 3676.255740]  __schedule+0x10c/0x570
[ 3676.259321]  schedule+0x58/0x80
[ 3676.262546]  worker_thread+0x370/0x468
[ 3676.266400]  kthread+0x110/0x120
[ 3676.269715]  ret_from_fork+0x10/0x1c
[ 3676.273393] Code: a9425bf5 a8c37bfd d65f03c0 d503201f (f9404407) 
[ 3676.279660] ---[ end trace fa914749a4dc6031 ]---
[ 3676.285581] Kernel panic - not syncing: Fatal exception
[ 3676.289785] SMP: stopping secondary CPUs
[ 3676.293816] Kernel Offset: disabled
[ 3676.297399] CPU features: 0x0,00002008
[ 3676.301249] Memory Limit: none
[ 3676.304922] Rebooting in 3 seconds..
[12929.680240] Internal error: synchronous parity or ECC error: 86000018 [#1] SMP
[12929.684836] Modules linked in: ath9k ath9k_common xt_connlimit nf_conncount iptable_nat ipt_MASQUERADE ath9k_hw ath xt_state xt_nat xt_helper xt_conntrack xt_connmark xt_connbytes xt_REDIRECT xt_NETMAP xt_FLOWOFFLOAD xt_CT nf_nat_ipv4 nf_nat nf_flow_table_hw nf_flow_table nf_conntrack_rtcache nf_conntrack mac80211 ipt_REJECT cfg80211 xt_time xt_tcpudp xt_tcpmss xt_string xt_statistic xt_recent xt_quota xt_pkttype xt_owner xt_multiport xt_mark xt_mac xt_limit xt_length xt_hl xt_ecn xt_dscp xt_condition xt_comment xt_bpf xt_addrtype xt_TCPMSS xt_LOG xt_HL xt_DSCP xt_CLASSIFY ts_kmp ts_fsm ts_bm nf_reject_ipv4 nf_log_ipv4 nf_defrag_ipv6 nf_defrag_ipv4 iptable_raw iptable_mangle iptable_filter ipt_ECN ip_tables compat nf_log_ipv6 nf_log_common ip6table_mangle ip6table_filter ip6_tables ip6t_REJECT x_tables
[12929.758123]  nf_reject_ipv6 tun gpio_button_hotplug
[12929.763145] Process kworker/0:0 (pid: 5, stack limit = 0x00000000f766a017)
[12929.770227] CPU: 0 PID: 5 Comm: kworker/0:0 Not tainted 4.19.85 #0
[12929.776582] Hardware name: Globalscale Marvell ESPRESSOBin Board (DT)
[12929.783224] Workqueue:            (null) (events)
[12929.788054] pstate: 80400085 (Nzcv daIf +PAN -UAO)
[12929.792990] pc : __schedule+0x348/0x570
[12929.796923] lr : __schedule+0x2d0/0x570
[12929.800862] sp : ffffff800804bd90
[12929.804268] x29: ffffff800804bd90 x28: 0000000000000000 
[12929.809733] x27: ffffffc03ffccef0 x26: ffffffc03ffccea0 
[12929.815199] x25: 0000000000000000 x24: ffffffc00427af10 
[12929.820664] x23: ffffff8008666460 x22: ffffff800884e018 
[12929.826129] x21: ffffffc00427de80 x20: ffffffc00427aa00 
[12929.831595] x19: ffffffc03ffcd500 x18: 0000000000000000 
[12929.837061] x17: 0000000000000000 x16: 0000000000000000 
[12929.842526] x15: 0000000000000000 x14: 0000000000000000 
[12929.847992] x13: 0000000000000002 x12: 0000000000000000 
[12929.853458] x11: ffffffc03ffc94d0 x10: 00000000000007c0 
[12929.858924] x9 : ffffffc004230168 x8 : ffffff80088a9b08 
[12929.864388] x7 : 0000000000000000 x6 : 000000199ea477c6 
[12929.869855] x5 : 000000000000030f x4 : 00000bc26cff1000 
[12929.875320] x3 : ffffffc03ffcdef8 x2 : ffffffc03ffcdef8 
[12929.880785] x1 : ffffffc03ffcdef8 x0 : 0000000000000008 
[12929.886251] Call trace:
[12929.888764]  __schedule+0x348/0x570
[12929.892348]  schedule+0x58/0x80
[12929.895575]  worker_thread+0x370/0x468
[12929.899428]  kthread+0x110/0x120
[12929.902742]  ret_from_fork+0x10/0x1c
[12929.906418] Code: b5fffeb7 d4210000 f9800291 c85f7e80 (927ef800) 
[12929.912686] ---[ end trace 5f4e2dd5c1da7acd ]---
[12929.918593] Kernel panic - not syncing: Fatal exception
[12929.922812] SMP: stopping secondary CPUs
[12929.926844] Kernel Offset: disabled
[12929.930426] CPU features: 0x0,00002008
[12929.934277] Memory Limit: none
[12929.937946] Rebooting in 3 seconds..
01.12.20192647Base systemBug ReportVery LowHighEA6350v3 (IPQ4018) memory usage climbs until processes ...openwrt-19.07Unconfirmed Task Description

Device is Linksys EA6350v3

Issue occurs on 19.07 rc1, 19.07 rc2 and snapshot r11595 (snapshot version is by memory, but pretty sure that’s what I had on it).

Information for this bug report is based on 19.07 rc2 with the following packages installed for future potential use, but most not in use:
luci-app-sqm luci-proto-wireguard luci-app-wireguard ca-bundle curl https_dns_proxy luci-app-https_dns_proxy luci-app-statistics luci-app-samba kmod-usb-printer p910nd luci-app-p910nd diffutils minidlna luci-app-minidlna

Note: sqm, wireguard, https_dns_proxy, samba, usb printer, p910nd server, and minidlna are NOT in use. These are just the typical packages I add to my
router for future use.

Steps to reproduce:
Problem occurs after router runs for a few hours. EA6350v3 is set up as a wired access point for an EdgeRouter X (also on 19.07 rc2). The Edgerouter provides sqm and DNS and DHCP for LAN, guest and IOT VLANs. There are ~3 “Guest” 2.4 G wifi clients (a smart switch, an IP camera, a DEEBOT vacuum); the IOT VLAN is mapped to a physical port with an Ooma Telo plugged in (I know - I need to map the guest devices to IOT wifi someday...). The LAN is mapped to a physical port with a Roku 3 plugged in and to normal wifi. There are another ~4 or 5 5GHz wifi clients on the LAN wifi (a laptop, a couple Amazon Echo’s, a Google Home Mini, a Samsung Orbit Android phone) and a 2.4G LG Android phone on the 2.4 GHz wifi. CPU loading is quite low.

Memory usage starts out rather high (~100MB, climbs and climbs, eventually drops, climbs again, repeats. Eventually (a day or two) processes start getting killed to free up memory and things start dying. I have an EA8500 setup almost identically as a second AP in the house, and it’s memory usage sits around 50 MB versus 100MB to 200+MB for the EA6350v3. Something’s just not right...

The final message in the logs that repeats until processes begin to get killed is:

kern.warn kernel: [15897.905286] ath10k_ahb a000000.wifi: failed to increase tx pending count: -16, dropping

But the weird memory usage pattern precedes this message in the logs.

I’ve attached memory usage graphs and system and kernel logs from 19.07 rc2 to illustrate the problem. rc1 and snapshot behaved the same. This post also has logs showing processes getting killed if that helps diagnose: https://forum.openwrt.org/t/ipq4018-linksys-ea6350v3-wifi-dead-after-24-48-hrs/49080/3?u=eginnc

17.12.20192681Base systemBug ReportVery LowHighISP's DHCP option 121 makes 18.06.5 get no default GWopenwrt-18.06Unconfirmed Task Description

HW: TP-Link TL-WR1043ND v1
Openwrt affected: tried 18.06.4, 18.06.5

DHCP offer from ISP:

22:48:09.365836 00:04:96:51:fe:50 > 74:ea:3a:d1:2d:16, ethertype IPv4 (0x0800), length 354: (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto UDP (17), length 340)
    10.45.64.5.67 > 213.xx.xx.23.68: BOOTP/DHCP, Reply, length 312, hops 1, xid 0x3313791, secs 63, Flags [none]
	  Your-IP 213.xx.xx.23
	  Gateway-IP 10.45.64.5
	  Client-Ethernet-Address 74:ea:3a:d1:2d:16
	  Vendor-rfc1048 Extensions
	    Magic Cookie 0x63825363
	    DHCP-Message Option 53, length 1: Offer
	    Server-ID Option 54, length 4: 46.xx.xx.202
	    Lease-Time Option 51, length 4: 43200
	    Subnet-Mask Option 1, length 4: 255.255.255.128
	    Default-Gateway Option 3, length 4: 213.xx.xx.5
	    Domain-Name-Server Option 6, length 8: 10.81.3.19,10.59.3.19
	    Domain-Name Option 15, length 10: "abcxyz.ru"
	    BR Option 28, length 4: 213.xx.xx.127
	    Classless-Static-Route Option 121, length 14: (213.xx.xx.0/25:213.xx.xx.5),(default:213.xx.xx.5)

18.06.5 reaction to Classless-Static-Route Option 121:

root@OpenWrt:~# ip r
192.168.1.0/24 dev br-lan scope link  src 192.168.1.1
213.хх.хх.0/25 via 213.хх.хх.5 dev eth0.2  src 213.хх.хх.23

Fixing:

root@OpenWrt:~# ip r del 213.xx.xx.0/25
root@OpenWrt:~# ip r add 213.xx.xx.0/25 dev eth0.2 src 213.xx.xx.23
root@OpenWrt:~# ip r add default via 213.xx.xx.5 dev eth0.2
root@OpenWrt:~# ip r
default via 213.xx.xx.5 dev eth0.2 
192.168.2.0/24 dev br-lan scope link  src 192.168.2.1 
213.xx.xx.0/25 dev eth0.2 scope link  src 213.xx.xx.23

All things above rised from my attempt to switch from 15.05.1 to new stable 18.06.x branch of Openwrt
15.05.1 works without a glitch with this ISP.

09.01.20202719Base systemBug ReportVery LowHighBuffalo WBMR-HP-G300H: DSL does not connect at all with...openwrt-19.07Unconfirmed Task Description

Supply the following if possible:
- Device problem occurs on: Buffalo WBMR-HP-G300H
- Software versions of OpenWrt/LEDE release, packages, etc.: OpenWRT 19.07, kmod-ltq-adsl-ar9-fw-a 0.1-1, which shows up as 4.4.4.0.0.1 in dsl_control status.
- Steps to reproduce:

1. Get an ADSL line from Rostelecom.
2. Upgrade the router to OpenWRT 19.07.
3. Reboot.

Result: DSL does not connect. In /etc/init.d/dsl_control status, it goes through all phases, then briefly shows as “Up”, but then the “dsl0” interface is not created, and the following lines are logged in dmesg:

 [   56.597766] [DSL_BSP_Showtime 914]: Datarate US intl = 1024000, fast = 0
 [   56.603091] [DSL_BSP_Showtime 934]: no hookup from ATM driver to set cell rate

The error does not exist with the 4.5.4.9.1.1 firmware obtained from unofficial sources. The bug has been submitted through the affected ADSL line with the unofficial firmware.

Status:

# /etc/init.d/dsl_control status
ATU-C Vendor ID: Broadcom 161.149
ATU-C System Vendor ID: 00,00,00,00,00,00,00,00
Chipset: Ifx-AR9
Firmware Version: 4.5.4.9.1.1
API Version: 3.24.4.4
XTSE Capabilities: 0×4, 0×0, 0×0, 0×0, 0×0, 0×0, 0×0, 0×0 Annex: A
Line Mode: G.992.1 (ADSL)
Profile:
Line State: UP [0×801: showtime_tc_sync]
Forward Error Correction Seconds (FECS): Near: 413342 / Far: 0
Errored seconds (ES): Near: 0 / Far: 0
Severely Errored Seconds (SES): Near: 0 / Far: 0
Loss of Signal Seconds (LOSS): Near: 0 / Far: 0
Unavailable Seconds (UAS): Near: 253 / Far: 253
Header Error Code Errors (HEC): Near: 0 / Far: 0
Non Pre-emtive CRC errors (CRC_P): Near: / Far:
Pre-emtive CRC errors (CRCP_P): Near: / Far:
Power Management Mode: L0 - Synchronized
Latency [Interleave Delay]: 8.0 ms [Interleave] 8.0 ms [Interleave]
Data Rate: Down: 9.952 Mb/s / Up: 1.024 Mb/s
Line Attenuation (LATN): Down: 32.2 dB / Up: 19.5 dB
Signal Attenuation (SATN): Down: 32.6 dB / Up: 19.5 dB
Noise Margin (SNR): Down: 6.1 dB / Up: 13.0 dB
Aggregate Transmit Power (ACTATP): Down: 20.0 dB / Up: 12.3 dB
Max. Attainable Data Rate (ATTNDR): Down: 8.848 Mb/s / Up: 1.204 Mb/s
Line Uptime Seconds: 1164
Line Uptime: 19m 24s

(yes, very bad line)

Config:

config atm-bridge ‘atm’

option vpi '1'
option encaps 'llc'
option payload 'bridged'
option nameprefix 'dsl'
option vci '50'
option unit '0'
option atmdev '0'

config dsl ‘dsl’

option annex 'a'
option firmware '/lib/firmware/dsl_ar9_firmware_adsl_a-04.05.04.09.01.01.bin'

config interface ‘wan’

option ifname 'dsl0'
option proto 'pppoe'
option ipv6 '1'
option username 'censored'
list dns '8.8.8.8'
list dns '8.8.4.4'
option peerdns '0'
option keepalive '60 5'
option password 'censored'
13.01.20202733Base systemBug ReportVery LowHighAth79 firmware accident enter to failsafe mode when reb...openwrt-19.07Unconfirmed Task Description

Sometime when reboot/reflash router, I see serial console messages:

[    5.868712] init: - preinit -
[    5.960699] random: procd: uninitialized urandom read (4 bytes read)
[    6.909058] random: jshn: uninitialized urandom read (4 bytes read)
[    7.327749] random: jshn: uninitialized urandom read (4 bytes read)
[    7.567130] random: jshn: uninitialized urandom read (4 bytes read)
[    7.638687] random: jshn: uninitialized urandom read (4 bytes read)
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    9.860896] eth0: link up (1000Mbps/Full duplex)
- failsafe button rfkill was pressed -
- failsafe -
[   12.309911] urandom_read: 3 callbacks suppressed
[   12.309921] random: dropbearkey: uninitialized urandom read (32 bytes read)
Generating 1024 [   12.323834] random: dropbearkey: uninitialized urandom read (32 bytes read)
bit rsa key, this may take a while...
Public key portion is:
ssh-rsa AAAAB3NzaC1yc2EAAAADAQABAAAAgQCKZVT/UJoTHz2CkNHrYmfzzBDfa/6Yd6+LJVcrURD15lbN3ch7AG/tc/ZolkeOrqkKD6dM2h4TsYv4+)
Fingerprint: sha1!! b9:a4:d3:94:71:b3:34:ae:a3:85:c8:e9:a7:c8:63:fd:74:52:5e:ad


BusyBox v1.30.1 () built-in shell (ash)

ash: can't access tty; job control turned off
  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 -----------------------------------------------------
 OpenWrt 19.07-SNAPSHOT, r10868-08d9828b76
 -----------------------------------------------------
================= FAILSAFE MODE active ================

I noticed when wifi on/off switch on router is on, sometime it accident enter failsafe mode. If switch to off, it’s not happen.
Issue happens with 841n v8/v9/v10 & 841hp v3 (same hardware as v9/10) model.


15.01.20202739Base systemBug ReportVery LowHighArbitrary File CreationAllUnconfirmed Task Description

There is no restriction on the path of the system log file(logread),which lead to overwritten important file,such as /etc/passwd. if /etc/passwd was overwritened,it will cause a denial of service. when a router was infected, The only way to fix is flash firmware.

In the background, function External Linkstart_service_file will deal the system logging request and use logread` to save log in specified file.

 PROG=/sbin/logread  
    
    start_service_file()                                                              
    {                                                                                 
            PIDCOUNT="$(( ${PIDCOUNT} + 1))"                                          
            local pid_file="/var/run/logread.${PIDCOUNT}.pid"                         
                                                                                      
            [ "$2" = 0 ] || {                                                         
                    echo "validation failed"                                          
                    return 1                                                          
            }                                                                         
            [ -z "${log_file}" ] && return                                            
                                                                                      
            mkdir -p "$(dirname "${log_file}")"                                       
                                                                                      
            procd_open_instance                                                       
            procd_set_param command "$PROG" -f -F "$log_file" -p "$pid_file"          
            [ -n "${log_size}" ] && procd_append_param command -S "$log_size"         
            procd_close_instance                                                      
    }   

POC

1. set the path of sustem log and buffer size

In System → logging page,System log buffer sizeset to 1KiB ,Write system log to file set to /etc/passwd. At the end , clicking “Save & Apply” button.

2. reboot or wait a moment

In order to produce some log to overwriten /etc/passwd , it need to reboot OpenWrt (the fasest way ) or wait a monent.

3. result

Denial of service: the LuCi web page display “Dad Gateway”. the same time , the internet was offline.

22.01.20202764Base systemBug ReportVery LowHighucert: ucert -A output is invalidTrunkUnconfirmed Task Description

ucert -A generates something that ucert cannot read back.

This happens because ucert -A appears to be appending several libubox “blobs” together, but cert_load() uses libubox’ blob_parse_untrusted() which expects to get a buffer with a single blob inside, and no padding.

Thus a valid ucert file with certificate and signature will be *bigger* than the first blob inside it, and blob_parse_untrusted() in libubox won’t even try to process it.

Since this renders ucert useless, severity is set to high.

This is related to FS#2762 and FS#2763

30.01.20202783Base systemBug ReportVery LowHighTP-Link Archer A7 v5 can't be flashet via tftpopenwrt-19.07Unconfirmed Task Description

Device: TP-Link Archer A7 (RU) Ver 5.0
Software: OpenWRT 19.07.0

I just bought this router. And I trying to flash it with openwrt-19.07.0-ath79-generic-tplink_archer-a7-v5-squashfs-factory.bin trough tftp.
In wireshark I clearly see that file was downloaded. But router didn’t flashed.
I tried to flash snapshot image wtih same result.
I checked sha256 sums and it matches.

When I reproduced same steps with original TP-Link update image it worked well. Seems like something prevents router from flashing OpenWRT image.

30.01.20202785Base systemBug ReportVery LowHighkernel loading during netboot fails on mikrotik devicesopenwrt-19.07Unconfirmed Task Description

Devices tested:

  • Mikrotik rb433
  • Mikrotik rb435g

Software version: Using the v19.07.1 tag.

Issue: There are a few packages, whose are leading the ramdisk “unbbotable”, more precise the device is not able to load the kernel. First this happened by kmod-scsi-core , I thought it must be some kernel-related issue. Afterthat I realised that either I enable the aforementioned kernel-module, or the libraries called libpcre and libpci, the boot procedure will stop at:

Gateway: 192.168.1.254
transfer started ................................... transfer ok, time=2.61s
setting up elf image... OK
jumping to kernel code OpenWrt kernel loader for AR7XXX/AR9XXX
Copyright (C) 2011 Gabor Juhos juhosg@openwrt.org Decompressing kernel... done!
Starting kernel at 80060000...

Compiling these packages only as a module results a nice bootable image. Firstly I thought that maybe my ramdisk is too large, but it is about only 4,5 MB - previously using older trunk I was able to boot up images over 5 MByte.
I have pasted the config file to the ticket. If you switch libpcre and libpci to M instead of * it will boot.

This issue was not there before, using the image built from 18.06.

31.01.20202791Base systemBug ReportVery LowHighIPv6 router advertisments lost after upgrade to 19.07openwrt-19.07Unconfirmed Task Description

I’ve just upgraded my linksys wrt-1200ac from 18.06.4 to 19.07.0

I’ve got a more-or-less out-of-the-box configuration with wired and wireless clients all connected to the ‘br-lan’ bridge. My ISP provides native IPv6. I’ve got odhcpd-ip6only installed, and a mixture of clients, some using SLAAC and some using DHCPv6.

When a wireless client that is configured for SLAAC (e.g. an android phone) connects, it sends an IPv6 router solicitation to ff02::1 and receives a router advertisement on its fe80::<something> address. That still works fine. But the client never receives any further router adverts, so the route times out after 1800 seconds and IPv6 connectivity is lost.

This is *only* going wrong with wireless clients: tcpdump on a wired client shows router adverts arriving on ff02::1 every few minutes. But tcpdump on a wireless client shows no router adverts after the initial one.

I’ve retested with 18.06.4 and the problem does not exist in that version.

11.02.20202831Base systemBug ReportVery LowHigh2.4Ghz Wifi speed degradation on WNDR3800AllUnconfirmed Task Description

I found that on WNDR3800, ath79 build 2.4Ghz Wifi slower than ar71xx build.
ath79 build only get about 3.5MB/s (2.4Ghz 40Mhz), ar71xx build get about 10MB/s. (2.4Ghz 40Mhz)
Same network, Same wifi channel, test on speedtest.
I think this is a serious performance issue.

- Device problem occurs on
WNDR3800(ath79) latest sources at master branch.

- Steps to reproduce
install ar71xx build
test on speedtest.net (Samsung S6 and Sony xz1 use 2.4G wifi)
install ath79 build
test on speedtest.net (Samsung S6 and Sony xz1 use 2.4G wifi)
download speed only half of ar71xx build.


16.02.20202835Base systemBug ReportVery LowHighMT7621: Clients disconnects.openwrt-19.07Unconfirmed Task Description

Hi! I have MT7621 and when to router connected more than 10 peoples router start disconnecting some peoples(have two networks guest and main on 2,4).

There is my settings:
config wifi-iface ‘default_radio0’ option device ‘radio0’ option network ‘lan’ option mode ‘ap’ option wpa_disable_eapol_key_retries ‘1’ option key ‘WIFIPASS’ option ssid ‘WIFINAME’ option encryption ‘psk2+ccmp’ option disassoc_low_ack ‘0’ (guest network have same settings)

Other info:
Newifi-D2
MediaTek MT7621 ver:1 eco:3
OpenWrt 19.07.1 r10911-c155900f66 / LuCI openwrt-19.07 branch git-20.045.27998-49999e9

I also noticed that before the client is disconnected from the network, it will lose the Internet.

 

Issue on github: https://github.com/openwrt/mt76/issues/358

Many peoples with Newifi3 D2 have same problem(in github links and more details).

PLEASE, FIX IT!

18.02.20202844Base systemBug ReportVery LowHighath10k on archer C7 v2: high latencyopenwrt-19.07Unconfirmed Task Description

On my Archer C7 v2, since the upgrade from 18.06 to 19.07, I sometimes get very high latency on my 5 GHz wifi network:

This is when pinging a wireless client from the router itself.

ping 192.168.12.167
PING 192.168.12.167 (192.168.12.167): 56 data bytes
64 bytes from 192.168.12.167: seq=0 ttl=64 time=1.334 ms
64 bytes from 192.168.12.167: seq=1 ttl=64 time=2.002 ms
64 bytes from 192.168.12.167: seq=2 ttl=64 time=1004.448 ms
64 bytes from 192.168.12.167: seq=3 ttl=64 time=4.342 ms
64 bytes from 192.168.12.167: seq=4 ttl=64 time=1.072 ms
64 bytes from 192.168.12.167: seq=5 ttl=64 time=2.074 ms
64 bytes from 192.168.12.167: seq=6 ttl=64 time=2.505 ms
64 bytes from 192.168.12.167: seq=7 ttl=64 time=1.059 ms
64 bytes from 192.168.12.167: seq=8 ttl=64 time=1.746 ms
64 bytes from 192.168.12.167: seq=9 ttl=64 time=1.176 ms
64 bytes from 192.168.12.167: seq=10 ttl=64 time=1.086 ms
64 bytes from 192.168.12.167: seq=11 ttl=64 time=1.072 ms
64 bytes from 192.168.12.167: seq=12 ttl=64 time=815.290 ms
64 bytes from 192.168.12.167: seq=13 ttl=64 time=1004.417 ms
64 bytes from 192.168.12.167: seq=14 ttl=64 time=4.294 ms
64 bytes from 192.168.12.167: seq=15 ttl=64 time=4.520 ms
64 bytes from 192.168.12.167: seq=16 ttl=64 time=1003.250 ms
64 bytes from 192.168.12.167: seq=17 ttl=64 time=3.125 ms
64 bytes from 192.168.12.167: seq=18 ttl=64 time=1.019 ms
64 bytes from 192.168.12.167: seq=19 ttl=64 time=2.066 ms
^C
--- 192.168.12.167 ping statistics ---
20 packets transmitted, 20 packets received, 0% packet loss
round-trip min/avg/max = 1.019/193.094/1004.448 ms

The upgrade to 19.07.1 didn’t solve the issue. What (temporarily) seem to work is to restart the wlan0 interface. After a few hours the problem comes back. The client is very close to the AP (less than 3 meters, although there is a floor between). Signal quality is reported as very good.

Station 54:60:09:d3:e4:d6 (on wlan0)
        inactive time:  540 ms
        rx bytes:       1082546
        rx packets:     6294
        tx bytes:       15523400
        tx packets:     11636
        tx retries:     0
        tx failed:      1
        rx drop misc:   0
        signal:         -66 [-76, -68, -71] dBm
        signal avg:     -62 [-72, -64, -67] dBm
        tx bitrate:     390.0 MBit/s VHT-MCS 8 80MHz short GI VHT-NSS 1
        rx bitrate:     390.0 MBit/s VHT-MCS 8 80MHz short GI VHT-NSS 1
        rx duration:    422088 us
        last ack signal:-95 dBm
        authorized:     yes
        authenticated:  yes
        associated:     yes
        preamble:       long
        WMM/WME:        yes
        MFP:            no
        TDLS peer:      no
        DTIM period:    2
        beacon interval:100
        short slot time:yes
        connected time: 447 seconds

I am using stock 19.07.1 firmware. I also tried changing the regulatory domain from CA to US but it didn’t help.
I will now try with the non-ct driver and firmware to see if it helps, as it worked fine on 18.06 which didn’t include the -ct firmware by default.

cat /etc/config/wireless

config wifi-device 'radio0'
        option type 'mac80211'
        option hwmode '11a'
        option path 'pci0000:00/0000:00:00.0'
        option htmode 'VHT80'
        option noscan '1'
        option country 'US'
        option channel '149'

config wifi-iface 'default_radio0'
        option device 'radio0'
        option key 'removed'
        option network 'lan'
        option mode 'ap'
        option ssid 'myssid5'
        option encryption 'psk2+ccmp'

config wifi-device 'radio1'
        option type 'mac80211'
        option channel '11'
        option hwmode '11g'
        option path 'platform/ahb/ahb:apb/18100000.wmac'
        option noscan '1'
#       option country 'CA'
        option htmode 'HT40'
        option require_mode 'g'

config wifi-iface 'default_radio1'
        option device 'radio1'
        option network 'lan'
        option mode 'ap'
        option ssid 'myssid'
        option encryption 'psk2+ccmp'
        option key 'removed'
        option ieee80211w '1'
21.02.20202847Base systemBug ReportVery LowHighbetween ath79-master-r12157-a1cfe0dcbb and ath79-master...TrunkUnconfirmed Task Description

Supply the following if possible:
- Device problem occurs on
Netgear WNDR3700v2

- Software versions of OpenWrt/LEDE release, packages, etc.

between ath79-master-r12157-a1cfe0dcbb and ath79-master-r12259 including the rename from wndr3700v2 to wndr3700-v2 OpenWrt lost its capability to detect the two radios.

- Steps to reproduce

 


root@router:/tmp# cat /etc/banner

_______                     ________        __

| |.—–.—–.—–.| | | |.—-.| |_
| - || _ | -| || | | || _|| _|
|
_|| |_||||||| ||

        |__| W I R E L E S S   F R E E D O M

—————————————————– OpenWrt SNAPSHOT, r12157-a1cfe0dcbb


root@router:/tmp# dmesg
[ 0.000000] Linux version 4.19.98 (moeller@work-horse) (gcc version 8.3.0 (OpenWrt GCC 8.3.0 r12053-9e799f3eee)) #0 Fri Jan 31 22:29:40 2020
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
[ 0.000000] MIPS: machine is Netgear WNDR3700v2
[ 0.000000] SoC: Atheros AR7161 rev 2
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0×0000000000000000-0x0000000003ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0×0000000000000000-0x0000000003ffffff]
[ 0.000000] Initmem setup node 0 [mem 0×0000000000000000-0x0000000003ffffff]
[ 0.000000] On node 0 totalpages: 16384
[ 0.000000] Normal zone: 144 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 16384 pages, LIFO batch:3
[ 0.000000] random: get_random_bytes called from start_kernel+0×98/0x4a8 with crng_init=0
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16240
[ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 57516K/65536K available (4327K kernel code, 176K rwdata, 1020K rodata, 1188K init, 206K bss, 8020K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 51
[ 0.000000] CPU clock: 680.000 MHz [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 5621354254 ns
[ 0.000008] sched_clock: 32 bits at 340MHz, resolution 2ns, wraps every 6316128254ns
[ 0.007800] Calibrating delay loop... 452.19 BogoMIPS (lpj=2260992)
[ 0.074071] pid_max: default: 32768 minimum: 301
[ 0.078916] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.085519] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.096880] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.106751] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.112960] pinctrl core: initialized pinctrl subsystem
[ 0.119019] NET: Registered protocol family 16
[ 0.428745] PCI host bridge /ahb/apb/pcie-controller@17010000 ranges:
[ 0.435198] MEM 0×0000000010000000..0x0000000016ffffff
[ 0.440426] IO 0×0000000000000000..0×0000000000000000 [ 0.463018] PCI host bridge to bus 0000:00
[ 0.467126] pci_bus 0000:00: root bus resource [mem 0×10000000-0x16ffffff]
[ 0.474044] pci_bus 0000:00: root bus resource [io 0×0000]
[ 0.479604] pci_bus 0000:00: root bus resource [??? 0×00000000 flags 0×0]
[ 0.486385] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.494769] pci 0000:00:11.0: [168c:ff1d] type 00 class 0×020000 [ 0.494800] pci 0000:00:11.0: reg 0×10: [mem 0×00000000-0x0000ffff]
[ 0.495095] pci 0000:00:12.0: [168c:ff1d] type 00 class 0×020000 [ 0.495122] pci 0000:00:12.0: reg 0×10: [mem 0×00000000-0x0000ffff]
[ 0.495679] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 0.495708] pci 0000:00:11.0: BAR 0: assigned [mem 0×10000000-0x1000ffff]
[ 0.502528] pci 0000:00:12.0: BAR 0: assigned [mem 0×10010000-0x1001ffff]
[ 0.512297] clocksource: Switched to clocksource MIPS
[ 0.518346] NET: Registered protocol family 2
[ 0.523491] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes)
[ 0.531183] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.538204] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.544573] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.551058] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.556944] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.563492] NET: Registered protocol family 1
[ 0.567890] PCI: CLS 0 bytes, default 32
[ 0.570473] Crashlog allocated RAM at address 0x3f00000
[ 0.576987] workingset: timestamp_bits=14 max_order=14 bucket_order=0
[ 0.589206] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.595083] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) © 2001-2006 Red Hat, Inc.
[ 0.615469] io scheduler noop registered
[ 0.619388] io scheduler deadline registered (default)
[ 0.625206] ar7100-usb-phy 18030000.usb-phy: phy reset is missing
[ 0.632106] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.639111] console [ttyS0] disabled
[ 0.642766] 18020000.uart: ttyS0 at MMIO 0×18020000 (irq = 10, base_baud = 10625000) is a 16550A
[ 0.651550] console [ttyS0] enabled
[ 0.658520] bootconsole [early0] disabled
[ 0.672685] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
[ 0.677766] 4 fixed-partitions partitions found on MTD device spi0.0
[ 0.684156] Creating 4 MTD partitions on “spi0.0”:
[ 0.688944] 0×000000000000-0×000000050000 : “u-boot” [ 0.694662] 0×000000050000-0×000000070000 : “u-boot-env” [ 0.700642] 0×000000070000-0x000000ff0000 : “firmware” [ 0.709051] 2 netgear-fw partitions found on MTD device firmware
[ 0.715111] Creating 2 MTD partitions on “firmware”:
[ 0.720073] 0×000000000000-0x0000001c4440 : “kernel” [ 0.725799] 0x0000001c4440-0x000000f80000 : “rootfs” [ 0.731378] mtd: device 4 (rootfs) set to be root filesystem
[ 0.738413] 1 squashfs-split partitions found on MTD device rootfs
[ 0.744648] 0x0000007b0000-0x000000f80000 : “rootfs_data” [ 0.750780] 0x000000ff0000-0×000001000000 : “art” [ 0.756658] Realtek RTL8366S ethernet switch driver version 0.2.2
[ 0.762862] rtl8366s rtl8366s: cannot find mdio node phandle
[ 0.768528] rtl8366s rtl8366s: using GPIO pins 5 (SDA) and 7 (SCK)
[ 0.774813] rtl8366s rtl8366s: RTL8366 ver. 1 chip found
[ 0.826529] libphy: rtl8366s: probed
[ 0.831545] libphy: Fixed MDIO Bus: probed
[ 1.184018] ag71xx 19000000.eth: connected to PHY at fixed-0:00 [uid=00000000, driver=Generic PHY]
[ 1.193617] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode: rgmii
[ 1.533893] ag71xx 1a000000.eth: connected to PHY at rtl8366s:04 [uid=001cc960, driver=Generic PHY]
[ 1.543585] eth1: Atheros AG71xx at 0xba000000, irq 5, mode: rgmii
[ 1.552067] NET: Registered protocol family 10
[ 1.561269] Segment Routing with IPv6
[ 1.565090] NET: Registered protocol family 17
[ 1.569586] 8021q: 802.1Q VLAN Support v1.8
[ 1.585516] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[ 1.596158] Freeing unused kernel memory: 1188K
[ 1.600682] This architecture does not have kernel memory protection.
[ 1.607138] Run /sbin/init as init process
[ 2.582308] random: fast init done
[ 2.807119] init: Console is alive
[ 2.810741] init: - watchdog -
[ 6.241610] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 6.383455] usbcore: registered new interface driver usbfs
[ 6.389022] usbcore: registered new interface driver hub
[ 6.394453] usbcore: registered new device driver usb
[ 6.430284] ehci_hcd: USB 2.0 ‘Enhanced’ Host Controller (EHCI) Driver
[ 6.445010] SCSI subsystem initialized
[ 6.453749] ehci-platform: EHCI generic platform driver
[ 7.058167] ehci-platform 1b000000.usb: EHCI Host Controller
[ 7.063869] ehci-platform 1b000000.usb: new USB bus registered, assigned bus number 1
[ 7.071783] ehci-platform 1b000000.usb: irq 3, io mem 0x1b000000
[ 7.102319] ehci-platform 1b000000.usb: USB 2.0 started, EHCI 1.00
[ 7.109300] hub 1-0:1.0: USB hub found
[ 7.113454] hub 1-0:1.0: 2 ports detected
[ 7.120810] ohci_hcd: USB 1.1 ‘Open’ Host Controller (OHCI) Driver
[ 7.128705] ohci-platform: OHCI generic platform driver
[ 7.134182] ohci-platform 1c000000.usb: Generic Platform OHCI controller
[ 7.140911] ohci-platform 1c000000.usb: new USB bus registered, assigned bus number 2
[ 7.148855] ohci-platform 1c000000.usb: irq 14, io mem 0x1c000000
[ 7.227154] hub 2-0:1.0: USB hub found
[ 7.231244] hub 2-0:1.0: 2 ports detected
[ 7.239911] usbcore: registered new interface driver usb-storage
[ 7.246968] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 7.257068] init: - preinit -
[ 7.952485] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 8.224006] usb-storage 1-1:1.0: USB Mass Storage device detected
[ 8.239044] scsi host0: usb-storage 1-1:1.0
[ 8.607425] random: procd: uninitialized urandom read (4 bytes read)
[ 9.217736] random: jshn: uninitialized urandom read (4 bytes read)
[ 9.313323] scsi 0:0:0:0: Direct-Access SanDisk Ultra 1.01 PQ: 0 ANSI: 2
[ 9.324268] sd 0:0:0:0: [sda] 31266816 512-byte logical blocks: (16.0 GB/14.9 GiB)
[ 9.435234] sd 0:0:0:0: [sda] Write Protect is off
[ 9.440027] sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00
[ 9.441159] sd 0:0:0:0: [sda] No Caching mode page found
[ 9.446536] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 9.467635] sda: sda1 sda2
[ 9.485172] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 9.512732] random: jshn: uninitialized urandom read (4 bytes read)
[ 9.803851] random: jshn: uninitialized urandom read (4 bytes read)
[ 9.855143] random: jshn: uninitialized urandom read (4 bytes read)
[ 9.937787] random: jshn: uninitialized urandom read (4 bytes read)
[ 10.734464] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 11.792658] eth0: link up (1000Mbps/Full duplex)
[ 11.797336] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 21.002121] mount_root: loading kmods from internal overlay
[ 21.065763] kmodloader: loading kernel modules from etc/modules-boot.d/*
[ 21.074086] kmodloader: done loading kernel modules from
etc/modules-boot.d/*
[ 22.067245] jffs2: notice: (573) jffs2_build_xattr_subsystem: complete building xattr subsystem, 4 of xdatum (3 unchecked, 1 orphan) and 38 of xref (1 dead, 0 orphan) found.
[ 22.083539] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 22.104478] block: extroot: not configured
[ 22.493615] jffs2: notice: (571) jffs2_build_xattr_subsystem: complete building xattr subsystem, 4 of xdatum (3 unchecked, 1 orphan) and 38 of xref (1 dead, 0 orphan) found.
[ 22.512972] mount_root: loading kmods from internal overlay
[ 22.571532] kmodloader: loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
[ 22.586940] kmodloader: done loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
[ 23.297496] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 23.311711] block: extroot: not configured
[ 23.317033] mount_root: switching to jffs2 overlay
[ 23.391179] overlayfs: upper fs does not support tmpfile.
[ 23.402971] urandom-seed: Seeding with /etc/urandom.seed
[ 23.506382] eth0: link down
[ 23.522968] procd: - early -
[ 23.525956] procd: - watchdog -
[ 24.224357] procd: - watchdog -
[ 24.227866] procd: - ubus -
[ 24.305816] urandom_read: 2 callbacks suppressed
[ 24.305823] random: ubusd: uninitialized urandom read (4 bytes read)
[ 24.321238] random: ubusd: uninitialized urandom read (4 bytes read)
[ 24.330097] procd: - init -
[ 25.653767] kmodloader: loading kernel modules from /etc/modules.d/*
[ 25.815614] ntfs: driver 2.1.32 [Flags: R/O MODULE].
[ 25.855111] tun: Universal TUN/TAP device driver, 1.6
[ 25.878662] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 25.922686] gre: GRE over IPv4 demultiplexor driver
[ 25.944224] ip_gre: GRE over IPv4 tunneling driver
[ 26.291706] Mirror/redirect action on
[ 26.325462] u32 classifier
[ 26.328171] input device check on
[ 26.331822] Actions configured
[ 26.380723] Loading modules backported from Linux version v5.4-rc8-0-gaf42d3466bdc
[ 26.388336] Backport generated by backports.git v5.4-rc8-1-0-g368e8c51
[ 26.401462] urngd: v1.0.2 started.
[ 26.492389] usbcore: registered new interface driver usbserial_generic
[ 26.498978] usbserial: USB Serial support registered for generic
[ 26.558787] wireguard: WireGuard 0.0.20200128 loaded. See www.wireguard.com for information.
[ 26.567273] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld Jason@zx2c4.com. All Rights Reserved.
[ 26.778103] xt_time: kernel timezone is -0000
[ 26.798642] ath9k_pci_owl_loader 0000:00:11.0: enabling device (0000 → 0002)
[ 26.806040] ath9k_pci_owl_loader 0000:00:12.0: enabling device (0000 → 0002)
[ 26.824088] ath9k_pci_owl_loader 0000:00:12.0: fixup device configuration
[ 26.832789] ath9k_pci_owl_loader 0000:00:11.0: fixup device configuration
[ 26.861449] pci 0000:00:12.0: [168c:0029] type 00 class 0×028000 [ 26.861487] pci 0000:00:12.0: reg 0×10: [mem 0×10010000-0x1001ffff]
[ 26.861542] pci 0000:00:12.0: PME# supported from D0 D3hot
[ 26.862141] pci 0000:00:12.0: BAR 0: assigned [mem 0×10010000-0x1001ffff]
[ 26.877545] pci 0000:00:11.0: [168c:0029] type 00 class 0×028000 [ 26.877582] pci 0000:00:11.0: reg 0×10: [mem 0×10000000-0x1000ffff]
[ 26.877638] pci 0000:00:11.0: PME# supported from D0 D3hot
[ 26.878247] pci 0000:00:11.0: BAR 0: assigned [mem 0×10000000-0x1000ffff]
[ 27.066477] random: crng init done
[ 27.156340] PPP generic driver version 2.4.2
[ 27.183974] PPP MPPE Compression module registered
[ 27.199611] NET: Registered protocol family 24
[ 27.218213] PPTP driver version 0.8.5
[ 27.368426] ath9k 0000:00:12.0: enabling device (0000 → 0002)
[ 27.408317] ath: phy0: Ignoring endianness difference in EEPROM magic bytes.
[ 27.416965] ath: EEPROM regdomain: 0×0 [ 27.416971] ath: EEPROM indicates default country code should be used
[ 27.416974] ath: doing EEPROM country→regdmn map search
[ 27.416984] ath: country maps to regdmn code: 0x3a
[ 27.416989] ath: Country alpha2 being used: US
[ 27.416992] ath: Regpair used: 0x3a
[ 27.433820] ieee80211 phy0: Selected rate control algorithm ‘minstrel_ht’ [ 27.435348] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xb0010000, irq=19
[ 27.442114] ath9k 0000:00:11.0: enabling device (0000 → 0002)
[ 27.584297] ath: phy1: Ignoring endianness difference in EEPROM magic bytes.
[ 27.592914] ath: EEPROM regdomain: 0×0 [ 27.592920] ath: EEPROM indicates default country code should be used
[ 27.592923] ath: doing EEPROM country→regdmn map search
[ 27.592933] ath: country maps to regdmn code: 0x3a
[ 27.592938] ath: Country alpha2 being used: US
[ 27.592940] ath: Regpair used: 0x3a
[ 27.607441] ieee80211 phy1: Selected rate control algorithm ‘minstrel_ht’ [ 27.608985] ieee80211 phy1: Atheros AR9280 Rev:2 mem=0xb0000000, irq=18
[ 27.702755] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 44.364371] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts:
[ 44.414576] Adding 976560k swap on /dev/sda1. Priority:-2 extents:1 across:976560k
[ 48.643400] eth0: link up (1000Mbps/Full duplex)
[ 48.648969] br-lan: port 1(eth0) entered blocking state
[ 48.654275] br-lan: port 1(eth0) entered disabled state
[ 48.659807] device eth0 entered promiscuous mode
[ 48.692372] br-lan: port 1(eth0) entered blocking state
[ 48.697596] br-lan: port 1(eth0) entered forwarding state
[ 48.703176] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 48.790578] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 48.835679] IPv6: ADDRCONF(NETDEV_UP): eth1.2: link is not ready
[ 48.951180] IPv6: ADDRCONF(NETDEV_UP): eth1.7: link is not ready
[ 49.712398] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 51.437743] eth1: link up (1000Mbps/Full duplex)
[ 51.513573] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 51.582425] IPv6: ADDRCONF(NETDEV_CHANGE): eth1.2: link becomes ready
[ 51.589118] IPv6: ADDRCONF(NETDEV_CHANGE): eth1.7: link becomes ready
[ 54.282504] ath: EEPROM regdomain: 0×8114 [ 54.286516] ath: EEPROM indicates we should expect a country code
[ 54.292634] ath: doing EEPROM country→regdmn map search
[ 54.297928] ath: country maps to regdmn code: 0×37 [ 54.302722] ath: Country alpha2 being used: DE
[ 54.307157] ath: Regpair used: 0×37 [ 54.310630] ath: regdomain 0×8114 dynamically updated by user
[ 54.316523] ath: EEPROM regdomain: 0×8114 [ 54.320516] ath: EEPROM indicates we should expect a country code
[ 54.326609] ath: doing EEPROM country→regdmn map search
[ 54.331904] ath: country maps to regdmn code: 0×37 [ 54.336698] ath: Country alpha2 being used: DE
[ 54.341125] ath: Regpair used: 0×37 [ 54.344620] ath: regdomain 0×8114 dynamically updated by user
[ 54.836482] pppoe-wan: renamed from ppp0
[ 57.427192] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 57.492852] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 57.616731] br-lan: port 2(wlan0) entered blocking state
[ 57.622045] br-lan: port 2(wlan0) entered disabled state
[ 57.627773] device wlan0 entered promiscuous mode
[ 57.632654] br-lan: port 2(wlan0) entered blocking state
[ 57.637986] br-lan: port 2(wlan0) entered forwarding state
[ 57.693619] br-lan: port 3(wlan1) entered blocking state
[ 57.698935] br-lan: port 3(wlan1) entered disabled state
[ 57.704667] device wlan1 entered promiscuous mode
[ 58.525536] br-lan: port 2(wlan0) entered disabled state
[ 58.531209] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 58.537780] br-lan: port 3(wlan1) entered blocking state
[ 58.543145] br-lan: port 3(wlan1) entered forwarding state
[ 58.750884] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 58.757483] br-lan: port 2(wlan0) entered blocking state
[ 58.762856] br-lan: port 2(wlan0) entered forwarding state
[84181.737818] pppoe-wan: renamed from ppp0
[144550.658055] pppoe-wan: renamed from ppp0
[159913.299297] eth1: link down
[159918.352853] IPv6: ADDRCONF(NETDEV_UP): eth1.7: link is not ready
[159919.249344] eth1: link up (1000Mbps/Full duplex)
[159919.251734] IPv6: ADDRCONF(NETDEV_CHANGE): eth1.7: link becomes ready
[159923.807531] eth1: link down
[159924.830488] eth1: link up (1000Mbps/Full duplex)
[159931.219728] eth1: link down
[159936.244722] IPv6: ADDRCONF(NETDEV_UP): eth1.7: link is not ready
[159950.979373] eth1: link up (1000Mbps/Full duplex)
[159950.982129] IPv6: ADDRCONF(NETDEV_CHANGE): eth1.7: link becomes ready
[160110.252218] pppoe-wan: renamed from ppp0
[246512.671046] pppoe-wan: renamed from ppp0
[260793.131776] pppoe-wan: renamed from ppp0
[347195.313169] pppoe-wan: renamed from ppp0
[433596.980231] pppoe-wan: renamed from ppp0
[449177.428433] pppoe-wan: renamed from ppp0
[535580.336441] pppoe-wan: renamed from ppp0
root@router:~#

BusyBox v1.31.1 () built-in shell (ash)

_______                     ________        __

| |.—–.—–.—–.| | | |.—-.| |_
| - || _ | -| || | | || _|| _|
|
_|| |_||||||| ||

        |__| W I R E L E S S   F R E E D O M

—————————————————– OpenWrt SNAPSHOT, r12259-2f1cc5c3d5


root@router:~# dmesg
[ 0.000000] Linux version 4.19.101 (moeller@work-horse) (gcc version 8.3.0 (OpenWrt GCC 8.3.0 r12053-9e799f3eee)) #0 Tue Feb 18 15:10:31 2020
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
[ 0.000000] MIPS: machine is Netgear WNDR3700 v2
[ 0.000000] SoC: Atheros AR7161 rev 2
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0×0000000000000000-0x0000000003ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0×0000000000000000-0x0000000003ffffff]
[ 0.000000] Initmem setup node 0 [mem 0×0000000000000000-0x0000000003ffffff]
[ 0.000000] On node 0 totalpages: 16384
[ 0.000000] Normal zone: 144 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 16384 pages, LIFO batch:3
[ 0.000000] random: get_random_bytes called from start_kernel+0×98/0x4a8 with crng_init=0
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16240
[ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 57452K/65536K available (4336K kernel code, 180K rwdata, 1020K rodata, 1240K init, 206K bss, 8084K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 51
[ 0.000000] CPU clock: 680.000 MHz [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 5621354254 ns
[ 0.000008] sched_clock: 32 bits at 340MHz, resolution 2ns, wraps every 6316128254ns
[ 0.007802] Calibrating delay loop... 452.19 BogoMIPS (lpj=2260992)
[ 0.074072] pid_max: default: 32768 minimum: 301
[ 0.078916] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.085519] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.096900] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.106767] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.112979] pinctrl core: initialized pinctrl subsystem
[ 0.119049] NET: Registered protocol family 16
[ 0.428873] PCI host bridge /ahb/apb/pcie-controller@17010000 ranges:
[ 0.435329] MEM 0×0000000010000000..0x0000000016ffffff
[ 0.440561] IO 0×0000000000000000..0×0000000000000000 [ 0.463724] PCI host bridge to bus 0000:00
[ 0.467827] pci_bus 0000:00: root bus resource [mem 0×10000000-0x16ffffff]
[ 0.474747] pci_bus 0000:00: root bus resource [io 0×0000]
[ 0.480307] pci_bus 0000:00: root bus resource [??? 0×00000000 flags 0×0]
[ 0.487093] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.495479] pci 0000:00:11.0: [168c:ff1d] type 00 class 0×020000 [ 0.495512] pci 0000:00:11.0: reg 0×10: [mem 0×00000000-0x0000ffff]
[ 0.495815] pci 0000:00:12.0: [168c:ff1d] type 00 class 0×020000 [ 0.495841] pci 0000:00:12.0: reg 0×10: [mem 0×00000000-0x0000ffff]
[ 0.496401] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 0.496430] pci 0000:00:11.0: BAR 0: assigned [mem 0×10000000-0x1000ffff]
[ 0.503258] pci 0000:00:12.0: BAR 0: assigned [mem 0×10010000-0x1001ffff]
[ 0.513082] clocksource: Switched to clocksource MIPS
[ 0.519172] NET: Registered protocol family 2
[ 0.524330] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes)
[ 0.532014] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.539035] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.545408] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.551886] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.557771] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.564323] NET: Registered protocol family 1
[ 0.568729] PCI: CLS 0 bytes, default 32
[ 0.571378] Crashlog allocated RAM at address 0x3f00000
[ 0.577915] workingset: timestamp_bits=14 max_order=14 bucket_order=0
[ 0.590375] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.596252] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) © 2001-2006 Red Hat, Inc.
[ 0.616936] io scheduler noop registered
[ 0.620852] io scheduler deadline registered (default)
[ 0.626692] ar7100-usb-phy 18030000.usb-phy: phy reset is missing
[ 0.633681] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.640613] console [ttyS0] disabled
[ 0.644274] 18020000.uart: ttyS0 at MMIO 0×18020000 (irq = 10, base_baud = 10625000) is a 16550A
[ 0.653058] console [ttyS0] enabled
[ 0.660028] bootconsole [early0] disabled
[ 0.674536] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
[ 0.679618] 4 fixed-partitions partitions found on MTD device spi0.0
[ 0.686021] Creating 4 MTD partitions on “spi0.0”:
[ 0.690808] 0×000000000000-0×000000050000 : “u-boot” [ 0.696550] 0×000000050000-0×000000070000 : “u-boot-env” [ 0.702548] 0×000000070000-0x000000ff0000 : “firmware” [ 0.711065] 2 netgear-fw partitions found on MTD device firmware
[ 0.717127] Creating 2 MTD partitions on “firmware”:
[ 0.722090] 0×000000000000-0x0000001c5440 : “kernel” [ 0.727837] 0x0000001c5440-0x000000f80000 : “rootfs” [ 0.733518] mtd: device 4 (rootfs) set to be root filesystem
[ 0.740540] 1 squashfs-split partitions found on MTD device rootfs
[ 0.746771] 0x0000007e0000-0x000000f80000 : “rootfs_data” [ 0.752926] 0x000000ff0000-0×000001000000 : “art” [ 0.758843] Realtek RTL8366S ethernet switch driver version 0.2.2
[ 0.765052] rtl8366s rtl8366s: cannot find mdio node phandle
[ 0.770719] rtl8366s rtl8366s: using GPIO pins 5 (SDA) and 7 (SCK)
[ 0.777005] rtl8366s rtl8366s: RTL8366 ver. 1 chip found
[ 0.827344] libphy: rtl8366s: probed
[ 0.833038] libphy: Fixed MDIO Bus: probed
[ 1.184827] ag71xx 19000000.eth: connected to PHY at fixed-0:00 [uid=00000000, driver=Generic PHY]
[ 1.194429] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode: rgmii
[ 1.534679] ag71xx 1a000000.eth: connected to PHY at rtl8366s:04 [uid=001cc960, driver=Generic PHY]
[ 1.544386] eth1: Atheros AG71xx at 0xba000000, irq 5, mode: rgmii
[ 1.552885] NET: Registered protocol family 10
[ 1.562197] Segment Routing with IPv6
[ 1.566017] NET: Registered protocol family 17
[ 1.570511] 8021q: 802.1Q VLAN Support v1.8
[ 1.587431] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[ 1.598222] Freeing unused kernel memory: 1240K
[ 1.602744] This architecture does not have kernel memory protection.
[ 1.609207] Run /sbin/init as init process
[ 2.583093] random: fast init done
[ 2.802168] init: Console is alive
[ 2.805875] init: - watchdog -
[ 6.090295] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 6.231212] usbcore: registered new interface driver usbfs
[ 6.236831] usbcore: registered new interface driver hub
[ 6.242219] usbcore: registered new device driver usb
[ 6.281739] SCSI subsystem initialized
[ 6.292568] usbcore: registered new interface driver usb-storage
[ 6.299577] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 6.309264] init: - preinit -
[ 8.224350] random: jshn: uninitialized urandom read (4 bytes read)
[ 8.466243] random: jshn: uninitialized urandom read (4 bytes read)
[ 8.754611] random: jshn: uninitialized urandom read (4 bytes read)
[ 9.618495] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 9.752825] urandom_read: 4 callbacks suppressed
[ 9.752833] random: procd: uninitialized urandom read (4 bytes read)
[ 10.673421] eth0: link up (1000Mbps/Full duplex)
[ 10.678056] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 20.006729] mount_root: loading kmods from internal overlay
[ 20.070104] kmodloader: loading kernel modules from etc/modules-boot.d/*
[ 20.078087] kmodloader: done loading kernel modules from
etc/modules-boot.d/*
[ 20.858277] jffs2_scan_eraseblock(): End of filesystem marker found at 0×30000 [ 20.865541] jffs2_build_filesystem(): unlocking the mtd device...
[ 20.865544] done.
[ 20.873637] jffs2_build_filesystem(): erasing all blocks after the end marker...
[ 78.939877] done.
[ 78.949323] jffs2: notice: (558) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 78.965200] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 78.972247] block: unable to load configuration (fstab: Entry not found)
[ 78.979108] block: attempting to load /tmp/jffs_cfg/etc/config/fstab
[ 78.985665] block: unable to load configuration (fstab: Entry not found)
[ 78.992448] block: attempting to load /etc/config/fstab
[ 79.062790] block: extroot: not configured
[ 79.566994] jffs2: notice: (556) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 80.268686] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 80.275845] block: unable to load configuration (fstab: Entry not found)
[ 80.282637] block: attempting to load /tmp/jffs_cfg/etc/config/fstab
[ 80.289201] block: unable to load configuration (fstab: Entry not found)
[ 80.296055] block: attempting to load /etc/config/fstab
[ 80.301752] block: extroot: not configured
[ 80.307978] mount_root: overlay filesystem has not been fully initialized yet
[ 80.321266] mount_root: switching to jffs2 overlay
[ 80.389579] overlayfs: upper fs does not support tmpfile.
[ 83.093791] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 83.182093] eth0: link down
[ 83.196988] procd: - early -
[ 83.199968] procd: - watchdog -
[ 83.834517] procd: - watchdog -
[ 83.837950] procd: - ubus -
[ 83.904783] random: ubusd: uninitialized urandom read (4 bytes read)
[ 83.912132] random: ubusd: uninitialized urandom read (4 bytes read)
[ 83.919702] procd: - init -
[ 84.893323] kmodloader: loading kernel modules from /etc/modules.d/*
[ 85.045275] tun: Universal TUN/TAP device driver, 1.6
[ 85.069431] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 85.119219] gre: GRE over IPv4 demultiplexor driver
[ 85.139270] ip_gre: GRE over IPv4 tunneling driver
[ 85.484432] Mirror/redirect action on
[ 85.511393] u32 classifier
[ 85.514167] input device check on
[ 85.517816] Actions configured
[ 85.563375] Loading modules backported from Linux version v5.4-rc8-0-gaf42d3466bdc
[ 85.570932] Backport generated by backports.git v5.4-rc8-1-0-g368e8c51
[ 85.594056] urngd: v1.0.2 started.
[ 85.779351] usbcore: registered new interface driver usbserial_generic
[ 85.786017] usbserial: USB Serial support registered for generic
[ 85.834097] wireguard: WireGuard 0.0.20200215 loaded. See www.wireguard.com for information.
[ 85.842525] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld Jason@zx2c4.com. All Rights Reserved.
[ 86.062495] xt_time: kernel timezone is -0000
[ 86.197742] random: crng init done
[ 86.337283] PPP generic driver version 2.4.2
[ 86.361591] PPP MPPE Compression module registered
[ 86.378734] NET: Registered protocol family 24
[ 86.408191] PPTP driver version 0.8.5
[ 86.566705] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 104.504191] eth0: link up (1000Mbps/Full duplex)
[ 104.509789] br-lan: port 1(eth0) entered blocking state
[ 104.515094] br-lan: port 1(eth0) entered disabled state
[ 104.520630] device eth0 entered promiscuous mode
[ 104.604615] br-lan: port 1(eth0) entered blocking state
[ 104.609845] br-lan: port 1(eth0) entered forwarding state
[ 104.615450] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 104.663301] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 104.708562] IPv6: ADDRCONF(NETDEV_UP): eth1.2: link is not ready
[ 104.808242] IPv6: ADDRCONF(NETDEV_UP): eth1.7: link is not ready
[ 105.553190] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 106.773996] eth1: link up (1000Mbps/Full duplex)
[ 106.851719] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 106.911421] IPv6: ADDRCONF(NETDEV_CHANGE): eth1.2: link becomes ready
[ 106.918175] IPv6: ADDRCONF(NETDEV_CHANGE): eth1.7: link becomes ready
[ 108.903192] pppoe-wan: renamed from ppp0
root@router:~#

Note, the lack of anything related to the ath9K driver in the second dmesg.

Following the instructions on External Linkhttps://openwrt.org/docs/guide-user/network/wifi/basic to regenerate the wireless configuration:
rm -f /etc/config/wireless
wifi config

resulted in an empty /etc/config/wireless:
root@router:~# ls -all /etc/config/wireless
-rw-r–r– 1 root root 0 Feb 21 23:12 /etc/config/wireless
root@ router:~# cat /etc/config/wireless

Due to the rename of the platform from wndr3700v2 to wndr3700-v2 the build config had to be edited (recreated by a new run of menuconfig).

Let me know if I can do anything to help get this debugged.

25.02.20202856Base systemBug ReportVery LowHighWifi "dies" (hostapd drops all clients) on some ar71xx ...openwrt-19.07New Task Description

This issue is very strange, i don’t even know if it’s just faulty hardware but i have it happening on multiple devices now

Most affected hardware

  • Nanobridge M5 , in this case transmitting enough data can trigger it almost instantly
  • TL-WR841ND , in this case i had it happen like 3-4 times a year
  • CPE 210 v3 , in this case it happens like each week

For the last one, which is running 19.07 i found on the system log

Tue Feb 25 07:38:58 2020 daemon.notice hostapd: wlan0: AP-STA-DISCONNECTED [redacted mac1]
Tue Feb 25 07:38:58 2020 daemon.info hostapd: wlan0: STA [redacted mac1] IEEE 802.11: disassociated due to inactivity
Tue Feb 25 07:38:59 2020 daemon.info hostapd: wlan0: STA [redacted mac1] IEEE 802.11: deauthenticated due to inactivity (timer DEAUTH/REMOVE)
Tue Feb 25 07:41:32 2020 daemon.notice hostapd: wlan0: AP-STA-DISCONNECTED [redacted mac2]
Tue Feb 25 07:41:32 2020 daemon.info hostapd: wlan0: STA [redacted mac2] IEEE 802.11: disassociated due to inactivity
Tue Feb 25 07:41:33 2020 daemon.info hostapd: wlan0: STA [redacted mac2] IEEE 802.11: deauthenticated due to inactivity (timer DEAUTH/REMOVE)
Tue Feb 25 07:42:49 2020 daemon.notice hostapd: wlan0: AP-STA-POLL-OK [redacted mac3]
Tue Feb 25 07:49:55 2020 daemon.notice hostapd: wlan0: AP-STA-POLL-OK [redacted mac3]
Tue Feb 25 07:55:02 2020 daemon.notice hostapd: wlan0: AP-STA-POLL-OK [redacted mac3]
Tue Feb 25 08:00:15 2020 daemon.notice hostapd: wlan0: AP-STA-POLL-OK [redacted mac3]
Tue Feb 25 08:05:25 2020 daemon.notice hostapd: wlan0: AP-STA-POLL-OK [redacted mac3]
Tue Feb 25 08:10:44 2020 daemon.notice hostapd: wlan0: AP-STA-POLL-OK [redacted mac3]
Tue Feb 25 08:16:00 2020 daemon.notice hostapd: wlan0: AP-STA-POLL-OK [redacted mac3]
Showing tasks 101 - 150 of 1140 Page 3 of 23 - 1 - 2 - 3 - 4 - 5 - Last >>

Available keyboard shortcuts

Tasklist

Task Details

Task Editing