|
10.08.2016 | 84 | Base system | Bug Report | Very Low | Critical | sysntp does not resolves IPv6 when IPv6 only stack | Trunk | Unconfirmed |
Task Description
sysntp (busybox ntp) does not resolve IPv6 addresses when the machine is IPv6 stack based only.
proposed solution exist:
https://dev.openwrt.org/attachment/ticket/12167/0001-busybox-make-ntpd-prefer-IPv6-addresses.patch
http://lists.busybox.net/pipermail/busybox/2016-August/084529.html
Already reported in
https://github.com/lede-project/source/issues/249
|
|
10.02.2017 | 494 | Base system | Bug Report | Very Low | Critical | NETDEV WATCHDOG: ptm0 (): transmit queue 0 timed out | All | New |
Task Description
I have a VDSL line with Plusnet (UK) - the connection is pppoe - ptm0.101. With the supplied modem/router the line and connection is stable with no disconnects. With LEDE the connection is established and works well until it disconnects (sometimes as early as few minutes other times it stays connected up to an hour). After the disconnect there is no reconnection until a reboot. Restarting wan interface (ifdown wan/ifup wan) or dsl connection (/etc/init.d/dslcontrol stop/start) does not help.
Supply the following if possible: - Device problem occurs on TP-w8970 and BTHomehub 5A (same crash on both lantiq based devices) - Software versions of LEDE release, packages, etc. Tested on LEDE RC2, earlier LEDE snapshot from October 2016, Openwrt CC - same symptoms - Steps to reproduce - VDSL connection on ptm0.101 via pppoe
Here is a trace of the crash (dmesg):
[ 1414.124413] —[ beginning trace ff034b465cdad16b ]— [ 1414.125631] WARNING: CPU: 0 PID: 0 at net/sched/sch_generic.c:303 dev_watchdog+0x1a8/0x2f0() [ 1414.126471] NETDEV WATCHDOG: ptm0 (): transmit queue 0 timed out [ 1414.132456] Modules linked in: ltq_ptm_vr9 option iptable_nat ath9k usb_wwan rt2800usb rt2800lib pppoe nf_nat_ipv4 nf_conntrack_ipv6 nf_conntrack_ipv4 l2tp_ppp ipt_REJECT ipt_MASQUERADE ath9k_common xt_time xt_tcpudp xt_tcpmss xt_statistic xt_state xt_recent xt_policy xt_nat xt_multiport xt_mark xt_mac xt_limit xt_length xt_id xt_hl xt_helper xt_esp xt_ecn xt_dscp xt_conntrack xt_connmark xt_connlimit xt_connbytes xt_comment xt_TCPMSS xt_REDIRECT xt_LOG xt_HL xt_DSCP xt_CT xt_CLASSIFY usbserial rt2x00usb rt2x00lib pppox ppp_async nf_reject_ipv4 nf_nat_redirect nf_nat_masquerade_ipv4 nf_nat nf_log_ipv4 nf_defrag_ipv6 nf_defrag_ipv4 nf_conntrack_rtcache nf_conntrack ltq_deu_vr9 iptable_raw iptable_mangle iptable_filter ipt_ah ipt_ECN ip_tables crc_itu_t crc_ccitt cdc_acm ath9k_hw ath10k_pci ath10k_core ath mac80211 cfg80211 compat drv_dsl_cpe_api drv_mei_cpe xt_set ip_set_list_set ip_set_hash_netiface ip_set_hash_netport ip_set_hash_netnet ip_set_hash_net ip_set_hash_netportnet ip_set_hash_mac ip_set_hash_ipportnet ip_set_hash_ipportip ip_set_hash_ipport ip_set_hash_ipmark ip_set_hash_ip ip_set_bitmap_port ip_set_bitmap_ipmac ip_set_bitmap_ip ip_set nfnetlink ip6t_REJECT nf_reject_ipv6 nf_log_ipv6 nf_log_common ip6table_raw ip6table_mangle ip6table_filter ip6_tables x_tables pppoatm ppp_generic slhc l2tp_ip6 l2tp_ip l2tp_eth sit l2tp_netlink l2tp_core udp_tunnel ip6_udp_tunnel ipcomp xfrm4_tunnel xfrm4_mode_tunnel xfrm4_mode_transport xfrm4_mode_beet esp4 ah4 tunnel4 ip_tunnel tun af_key xfrm_user xfrm_ipcomp xfrm_algo br2684 atm drv_ifxos echainiv sha256_generic sha1_generic jitterentropy_rng drbg md5 hmac des_generic cbc authenc usb_storage dwc2 uhci_hcd ehci_platform ehci_hcd sd_mod scsi_mod gpio_button_hotplug ext4 jbd2 mbcache aead crypto_null [ 1414.287462] CPU: 0 PID: 0 Comm: swapper Not tainted 4.4.7 #1 [ 1414.293130] Stack : 804b0000 00000001 00000000 00000000 805172b8 80516f43 80489a24 00000000 [ 1414.293130] 80673844 00010000 80510000 805159bc 80515abc 80055664 00000003 80510000 [ 1414.293130] 80491b4c 00000000 8048ff50 80511c44 80515abc 800535b0 00000006 00000001 [ 1414.293130] 00000000 80512000 00000000 00000000 00000000 00000000 00000000 00000000 [ 1414.293130] 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 1414.293130] ... [ 1414.328618] Call Trace: [ 1414.331095] [<800178a8>] show_stack+0×50/0×84 [ 1414.335454] [<8002af48>] warn_slowpath_common+0xa0/0xd0 [ 1414.340670] [<8002afa4>] warn_slowpath_fmt+0x2c/0×38 [ 1414.345636] [<802e637c>] dev_watchdog+0x1a8/0x2f0 [ 1414.350348] [<8005f7b0>] call_timer_fn.isra.5+0×24/0×80 [ 1414.355557] [<8005fa2c>] run_timer_softirq+0x1a4/0×208 [ 1414.360694] [<8002de80>] __do_softirq+0×298/0x2b0 [ 1414.365388] [<80002430>] ret_from_irq+0×0/0×4 [ 1414.369760] [<80013a8c>] r4k_wait_irqoff+0×18/0×20 [ 1414.374528] [<8004ff6c>] cpu_startup_entry+0xa4/0xf8 [ 1414.379508] [<80539bf8>] start_kernel+0×474/0×494 [ 1414.384180] [ 1414.385631] —[ end trace ff034b465cdad16b ]—
|
|
11.05.2017 | 775 | Base system | Bug Report | Very Low | Critical | flashing kirkwood u-boot page not aligned [Zyxel NSA-32... | Trunk | Unconfirmed |
Task Description
[code]/e-data/4089-AD8E/tools # flash_erase /dev/mtd0 0 4 Erasing 128 Kibyte @ 60000 – 100 % complete[/code]
now when I flash the LEDE uboot I get this
[code]/e-data/4089-AD8E # nandwrite /dev/mtd0 kirkwood/generic/u-boot-nsa325/u-boot.kwb Input file is not page aligned Data did not fit into device, due to bad blocks : Success[/code]
the expected should be [code]/ # nandwrite /dev/mtd0 /e-data/4089-AD8E/uboot.2016.05-tld-1.nsa325.mtd0.kwb Writing data to block 0 at offset 0×0 Writing data to block 1 at offset 0×20000 Writing data to block 2 at offset 0×40000 Writing data to block 3 at offset 0×60000[/code]
now I can’t even turn off my device. Hopeful to be resolve asap.
|
|
24.05.2017 | 801 | Base system | Bug Report | Very Low | Critical | R7800 wifi crashing | Trunk | Unconfirmed |
Task Description
- Device problem occurs on: Netgear Nighthawk X4S R7800 - Software versions of LEDE release, packages, etc.: LEDE Reboot SNAPSHOT r4173-5d48dc1146 / LuCI Master (git-17.141.68918-5ca3864) - Steps to reproduce Boot device, wait for it to crash within 24hours
The paste ending in Hn was recorder after wifi stopped working and i turned wifi off and on. The paste ending in Wu happend about 30 minutes after that and could only be resolved by rebooting the device.
|
|
18.10.2017 | 1074 | Base system | Bug Report | Very Low | Critical | NETDEV WATCHDOG: wlan2 (mwifiex_sdio): transmit queue 1... | Trunk | Unconfirmed |
Task Description
- Device problem occurs on: WRT3200ACM - Software versions of LEDE release, packages, etc.: LEDE Reboot SNAPSHOT r5096-a29848c / LuCI Master (git-17.260.43176-678c15c) - Steps to reproduce: I’ve been consistently having problems with wlan2 going offline after the router has been up for a day or so, but just stumbled across this in dmesg. I’ll see if I can figure out the circumstances leading to it.
[85338.316517] WARNING: CPU: 1 PID: 0 at net/sched/sch_generic.c:316 dev_watchdog+0x1b4/0×234 [85338.324820] NETDEV WATCHDOG: wlan2 (mwifiex_sdio): transmit queue 1 timed out [85338.331987] Modules linked in: pppoe ppp_async pppox ppp_generic nf_conntrack_ipv6 iptable_nat ipt_REJECT ipt_MASQUERADE xt_time xt_tcpudp xt_tcpmss xt_statistic xt_state xt_recent xt_nat xt_multiport xt_mark xt_mac xt_limit xt_length xt_hl xt_helper xt_ecn xt_dscp xt_conntrack xt_connmark xt_connlimit xt_connbytes xt_comment xt_TCPMSS xt_REDIRECT xt_LOG xt_HL xt_DSCP xt_CLASSIFY slhc rfcomm nf_reject_ipv4 nf_nat_redirect nf_nat_masquerade_ipv4 nf_conntrack_ipv4 nf_nat_ipv4 nf_nat nf_log_ipv4 nf_defrag_ipv6 nf_defrag_ipv4 nf_conntrack_rtcache nf_conntrack mwifiex_sdio mwifiex iptable_mangle iptable_filter ipt_ECN ip_tables hidp hci_uart crc_ccitt btusb btmrvl_sdio btmrvl btintel bnep bluetooth hid evdev input_core mwlwifi mac80211 cfg80211 compat xt_set ip_set_list_set ip_set_hash_netiface ip_set_hash_netport [85338.404541] ip_set_hash_netnet ip_set_hash_net ip_set_hash_netportnet ip_set_hash_mac ip_set_hash_ipportnet ip_set_hash_ipportip ip_set_hash_ipport ip_set_hash_ipmark ip_set_hash_ip ip_set_bitmap_port ip_set_bitmap_ipmac ip_set_bitmap_ip ip_set nfnetlink ip6t_REJECT nf_reject_ipv6 nf_log_ipv6 nf_log_common ip6table_mangle ip6table_filter ip6_tables x_tables tun regmap_mmio ecb cmac uhci_hcd ohci_platform ohci_hcd gpio_button_hotplug [85338.442106] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.9.54 #0 [85338.448049] Hardware name: Marvell Armada 380/385 (Device Tree) [85338.454003] [<c0016010>] (unwind_backtrace) from [<c0012220>] (show_stack+0×10/0×14) [85338.461782] [<c0012220>] (show_stack) from [<c020c1a0>] (dump_stack+0x7c/0x9c) [85338.469036] [<c020c1a0>] (dump_stack) from [<c0029218>] (warn+0xbc/0xec) [85338.475939] [<c0029218>] (warn) from [<c002927c>] (warn_slowpath_fmt+0×34/0×44) [85338.483455] [<c002927c>] (warn_slowpath_fmt) from [<c03b6c38>] (dev_watchdog+0x1b4/0×234) [85338.491661] [<c03b6c38>] (dev_watchdog) from [<c006ffe8>] (call_timer_fn+0×20/0×94) [85338.499349] [<c006ffe8>] (call_timer_fn) from [<c0070220>] (run_timer_softirq+0x1c4/0×200) [85338.507650] [<c0070220>] (run_timer_softirq) from [<c002d2b4>] (do_softirq+0xd0/0×204) [85338.515775] [<c002d2b4>] (do_softirq) from [<c002d66c>] (irq_exit+0×94/0xb8) [85338.523029] [<c002d66c>] (irq_exit) from [<c0061e04>] (handle_domain_irq+0×90/0xb4) [85338.530892] [<c0061e04>] (handle_domain_irq) from [<c0009428>] (gic_handle_irq+0×50/0×94) [85338.539277] [<c0009428>] (gic_handle_irq) from [<c0012c8c>] (irq_svc+0x6c/0×90) [85338.546789] Exception stack(0xdf475f90 to 0xdf475fd8) [85338.551860] 5f80: 00000001 00000000 00000000 c001b1c0 [85338.560071] 5fa0: 00000000 df474000 c0604fe4 00000002 c05ff168 00000000 df475fe8 00000001 [85338.568282] 5fc0: 00000000 df475fe0 c000f808 c000f80c 60000013 ffffffff [85338.574925] [<c0012c8c>] (irq_svc) from [<c000f80c>] (arch_cpu_idle+0x2c/0×38) [85338.582355] [<c000f80c>] (arch_cpu_idle) from [<c005b154>] (cpu_startup_entry+0xf0/0x19c) [85338.590567] [<c005b154>] (cpu_startup_entry) from [<000095ac>] (0x95ac) [85338.597214] —[ end trace 7ee504210e2aead0 ]— [85338.601865] mwifiex_sdio mmc0:0001:1: 8504333 : Tx timeout(#1), bss_type-num = 1-0 [85344.871433] mwifiex_sdio mmc0:0001:1: 8504960 : Tx timeout(#2), bss_type-num = 1-0 [85350.631045] mwifiex_sdio mmc0:0001:1: 8505536 : Tx timeout(#3), bss_type-num = 1-0 [85356.400657] mwifiex_sdio mmc0:0001:1: 8506113 : Tx timeout(#4), bss_type-num = 1-0 [85366.309996] mwifiex_sdio mmc0:0001:1: 8507104 : Tx timeout(#5), bss_type-num = 1-0 [85376.309327] mwifiex_sdio mmc0:0001:1: 8508104 : Tx timeout(#6), bss_type-num = 1-0 [85386.318652] mwifiex_sdio mmc0:0001:1: 8509105 : Tx timeout(#7), bss_type-num = 1-0 [85386.326257] mwifiex_sdio mmc0:0001:1: tx_timeout_cnt exceeds threshold. Triggering card reset! [85386.356950] mwifiex_sdio mmc0:0001:1: info: shutdown mwifiex... [85386.362967] mwifiex_sdio mmc0:0001:1: PREP_CMD: card is removed [85386.368924] mwifiex_sdio mmc0:0001:1: Failed to delete mgmt IEs! [85386.374978] mwifiex_sdio mmc0:0001:1: PREP_CMD: card is removed [85386.380928] mwifiex_sdio mmc0:0001:1: Failed to stop the BSS [85386.387009] br-lan: port 4(wlan2) entered disabled state [85386.394495] device wlan2 left promiscuous mode [85386.398975] br-lan: port 4(wlan2) entered disabled state [85386.404593] mwifiex_sdio mmc0:0001:1: PREP_CMD: card is removed [85386.410562] mwifiex_sdio mmc0:0001:1: PREP_CMD: card is removed [85386.416507] mwifiex_sdio mmc0:0001:1: PREP_CMD: card is removed [85386.603147] mwifiex_sdio mmc0:0001:1: WLAN FW already running! Skip FW dnld [85386.610161] mwifiex_sdio mmc0:0001:1: WLAN FW is active [85396.707953] mwifiex_sdio mmc0:0001:1: mwifiex_cmd_timeout_func: Timeout cmd id = 0xa9, act = 0×0 [85396.716787] mwifiex_sdio mmc0:0001:1: num_data_h2c_failure = 0 [85396.722652] mwifiex_sdio mmc0:0001:1: num_cmd_h2c_failure = 0 [85396.728423] mwifiex_sdio mmc0:0001:1: is_cmd_timedout = 1 [85396.733842] mwifiex_sdio mmc0:0001:1: num_tx_timeout = 0 [85396.739178] mwifiex_sdio mmc0:0001:1: last_cmd_index = 3 [85396.744512] mwifiex_sdio mmc0:0001:1: last_cmd_id: b3 00 b3 00 b2 00 a9 00 b3 00 [85396.751940] mwifiex_sdio mmc0:0001:1: last_cmd_act: 00 00 00 00 00 00 00 00 00 00 [85396.759457] mwifiex_sdio mmc0:0001:1: last_cmd_resp_index = 2 [85396.765225] mwifiex_sdio mmc0:0001:1: last_cmd_resp_id: b3 80 b3 80 b2 80 b3 80 b3 80 [85396.773093] mwifiex_sdio mmc0:0001:1: last_event_index = 2 [85396.778603] mwifiex_sdio mmc0:0001:1: last_event: 37 00 55 00 43 00 55 00 55 00 [85396.785944] mwifiex_sdio mmc0:0001:1: data_sent=1 cmd_sent=1 [85396.791630] mwifiex_sdio mmc0:0001:1: ps_mode=0 ps_state=0 [85396.797372] mwifiex_sdio mmc0:0001:1: info: _mwifiex_fw_dpc: unregister device
|
|
21.10.2017 | 1094 | Base system | Bug Report | Very Low | Critical | no connection on any ethernet ports (incl internet) on ... | Trunk | Unconfirmed |
Task Description
Yesterday I upgraded the Linksys wrt1200ac from openwrt 15.05.1 to lede-17.01.4. The upgrade was done through a luci web interface.
After reboot the wan connection was gone, as well as all local ethernet ports. Wifi continued to work fine. The configuration seems to have survived the upgrade. I couldn’t find anything wrong with the configuration.
On the Internet port there were no packets coming in. On the ethernet port 1 there are bootp/dhcp requests coming from the router.
Not sure if that is relevant, but reverting back to 15.05.1 didn’t work either: the router is currently completely inaccessible. I don’t have a serial cable, will probably order one to try to debrick the thing.
|
|
08.11.2017 | 1158 | Base system | Bug Report | Very Low | Critical | ATH10k QCA9880 5 Ghz mixed mode (sta and ap) not possib... | Trunk | Unconfirmed |
Task Description
Hardware: Archer C7 V2 Software: Trunk (r5280)
Using the 5 Ghz radio in accesspoint mode (mode ap) and client mode (mode sta) at the same time doesnt work. Only client mode works. No error messages will be generated. With version V17.01.4 all is fine (same configuration).
Config details:
config wifi-device 'radio0'
option type 'mac80211'
option hwmode '11a'
option path 'pci0000:01/0000:01:00.0'
option noscan '1'
option htmode 'VHT80'
option multicast_querier '0'
option igmp_snooping '0'
option distance '8'
option log_level '3'
option compression '1'
option bursting '1'
option ff '1'
option country 'US'
option txpower '23'
option channel '112'
config wifi-device 'radio1'
option type 'mac80211'
option hwmode '11g'
option path 'platform/qca955x_wmac'
option noscan '1'
option htmode 'HT40'
option distance '15'
option multicast_querier '0'
option igmp_snooping '0'
option log_level '3'
option compression '1'
option bursting '1'
option ff '1'
option channel '9'
option country 'US'
option txpower '24'
option disabled '0'
config wifi-iface
option encryption 'psk2'
option device 'radio0'
**option mode 'sta'**
option bssid '08:96:D7:7B:89:BA'
option key 'xxxxxxxxxxxxxxxxxxxxxx'
option multicast_querier '0'
option igmp_snooping '0'
option ssid 'Fritz_5Ghz'
option network 'WWAN WWAN6'
config wifi-iface
option ssid 'im6shop'
option device 'radio1'
option key 'xxxxxxxxxxxxxxxxxxxxxx'
option multicast_querier '0'
option igmp_snooping '0'
option network 'LAN'
option mode 'ap'
option encryption 'psk2'
config wifi-iface
option device 'radio0'
**option mode 'ap'**
option key 'xxxxxxxxxxxxxxxxxxxxxx'
option macfilter 'allow'
list maclist '78:0C:B8:8A:12:45'
list maclist '88:32:9B:F6:70:79'
list maclist 'F0:27:65:7F:7A:19'
option encryption 'psk2+ccmp'
option network 'LAN'
option ssid 'im6shop'
If you need further details, let me know
regards Klaus
|
|
25.01.2018 | 1300 | Base system | Bug Report | Very Low | Critical | RT-N12+(MT7620N): WLAN not working. | Trunk | Unconfirmed |
Task Description
Hello,
Device: RT-N12+ Issue: WLAN is not working properly. When enabled the signal status shows 0db noise 0db. Wireless devices would properly show the SSID however unable to join. Even with No encryption. The system log would even show that radio0 is up. Steps done: - Reboot Router - Re-flash firmware - Manually set WiFi config: Band 20mhz or 40mhz. - Toggled between N and Legacy. - Manually set WiFi channels. - Tried different encryption.
Additional information: - I am well aware that this router support is still WIP as stated: https://lede-project.org/toh/hwdata/asus/asus_rt-n12 Basically just putting out this bug report since so far everything seemed fine except for wireless broadcast. - Used latest snapshot build from downloads page dated: Thu Jan 25 12:07:37 2018
|
|
28.01.2018 | 1307 | Base system | Bug Report | Very Low | Critical | ClearFog initramfs broken | All | Unconfirmed |
Task Description
It appears this has been broken for quite some time, likely before LEDE forked from OpenWrt, as there are CC builds with initrams images working fine (early 2016), however the CC repo no longer compiles a working initrams image, nor does LEDE.
Unexpected Output
Current LEDE/OpenWrt initramfs image is a mess all around (Compiled 2018.01.25)
Marvell>> tftpboot lede-mvebu-armada-388-clearfog-pro-initramfs.bin
Using egiga1 device
TFTP from server 10.4.50.38; our IP address is 10.4.50.170
Filename 'lede-mvebu-armada-388-clearfog-pro-initramfs.bin'.
Load address: 0x2000000
Loading: #################################################################
#################################################################
#################################################################
2.4 MiB/s
done
Bytes transferred = 4690096 (4790b0 hex)
Marvell>> bootm
Wrong Image Format for bootm command
ERROR: cant get kernel image!
Booting a LEDE zImage goes a bit better (...until the kernel panic | Compiled 2018.01.25)
Marvell>> tftpboot zImage-Solidrun-Clearfog-A1
Using egiga1 device
TFTP from server 10.4.50.38; our IP address is 10.4.50.170
Filename 'zImage-Solidrun-Clearfog-A1'.
Load address: 0x2000000
Loading: #################################################################
#################################################################
#################################################################
2.4 MiB/s
done
Bytes transferred = 2132324 (208964 hex)
Marvell>> bootz
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.4.14 (thepeople@trabant) (gcc version 5.3.0 (OpenWrt GCC 5.3.0 50140) ) #1 SMP Thu Dec 7 14:50:07 UTC 2017
[ 0.000000] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: SolidRun Clearfog A1
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] PERCPU: Embedded 12 pages/cpu @ef7ce000 s17984 r8192 d22976 u49152
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260608
[ 0.000000] Kernel command line:
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 1032820K/1048576K available (4223K kernel code, 178K rwdata, 1572K rodata, 264K init, 301K bss, 15756K reserved, 0K cma-reserved, 262144K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc05b1078 (5797 kB)
[ 0.000000] .init : 0xc05b2000 - 0xc05f4000 ( 264 kB)
[ 0.000000] .data : 0xc05f4000 - 0xc0620a5c ( 179 kB)
[ 0.000000] .bss : 0xc0620a5c - 0xc066c244 ( 302 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] mvebu_mbus: [Firmware Warn]: deprecated mbus-mvebu Device Tree, suspend/resume will not work
[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9
[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9
[ 0.000000] L2C-310 D prefetch enabled, offset 1 lines
[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled
[ 0.000000] L2C-310 Coherent cache controller enabled, 16 ways, 1024 kB
[ 0.000000] L2C-310 Coherent: CACHE_ID 0x410054c9, AUX_CTRL 0x56070001
[ 0.000000] Switching to timer-based delay loop, resolution 40ns
[ 0.000002] sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 85899345900ns
[ 0.000009] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns
[ 0.000106] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=250000)
[ 0.000113] pid_max: default: 32768 minimum: 301
[ 0.000148] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000152] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000340] CPU: Testing write buffer coherency: ok
[ 0.000439] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.000465] Setting up static identity map for 0x8280 - 0x82d8
[ 0.000550] mvebu-soc-id: MVEBU SoC ID=0x6828, Rev=0x4
[ 0.000633] mvebu-pmsu: Initializing Power Management Service Unit
[ 0.001026] Booting CPU 1
[ 0.001190] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.001218] Brought up 2 CPUs
[ 0.001223] SMP: Total of 2 processors activated (100.00 BogoMIPS).
[ 0.001226] CPU: All CPU(s) started in SVC mode.
[ 0.002883] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 0.002954] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.003000] pinctrl core: initialized pinctrl subsystem
[ 0.003380] NET: Registered protocol family 16
[ 0.003837] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.029930] cpuidle: using governor ladder
[ 0.032504] mvebu-pmsu: CPU hotplug support is currently broken on Armada 38x: disabling
[ 0.032512] mvebu-pmsu: CPU idle is currently broken on Armada 38x: disabling
[ 0.060714] SCSI subsystem initialized
[ 0.060995] usbcore: registered new interface driver usbfs
[ 0.061020] usbcore: registered new interface driver hub
[ 0.061042] usbcore: registered new device driver usb
[ 0.061712] clocksource: Switched to clocksource armada_370_xp_clocksource
[ 0.062143] NET: Registered protocol family 2
[ 0.062382] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.062424] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.062484] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.062516] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.062538] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.062619] NET: Registered protocol family 1
[ 0.062981] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.065945] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.065956] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.066587] bounce: pool size: 64 pages
[ 0.066594] io scheduler noop registered
[ 0.066599] io scheduler deadline registered (default)
[ 0.066978] armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver
[ 0.067276] irq: Cannot allocate irq_descs @ IRQ50, assuming pre-allocated
[ 0.067412] irq: Cannot allocate irq_descs @ IRQ82, assuming pre-allocated
[ 0.067660] mv_xor f1060800.xor: Marvell shared XOR driver
[ 0.101937] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr )
[ 0.102017] mv_xor f1060900.xor: Marvell shared XOR driver
[ 0.141919] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr )
[ 0.142055] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.142889] console [ttyS0] disabled
[ 0.162961] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 23, base_baud = 15625000) is a 16550A
[ 0.715227] console [ttyS0] enabled
[ 0.738916] f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 24, base_baud = 15625000) is a 16550A
[ 0.748295] ahci-mvebu f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode
[ 0.757374] ahci-mvebu f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs
[ 0.766754] scsi host0: ahci-mvebu
[ 0.770314] scsi host1: ahci-mvebu
[ 0.773824] ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 45
[ 0.781766] ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 45
[ 0.789792] ahci-mvebu f10e0000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode
[ 0.798869] ahci-mvebu f10e0000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs
[ 0.808345] scsi host2: ahci-mvebu
[ 0.811918] scsi host3: ahci-mvebu
[ 0.815415] ata3: SATA max UDMA/133 mmio [mem 0xf10e0000-0xf10e1fff] port 0x100 irq 46
[ 0.823359] ata4: SATA max UDMA/133 mmio [mem 0xf10e0000-0xf10e1fff] port 0x180 irq 46
[ 0.832327] libphy: Fixed MDIO Bus: probed
[ 0.836538] libphy: orion_mdio_bus: probed
[ 0.841803] mvneta f1030000.ethernet eth0: Using hardware mac address 00:50:43:4c:18:3b
[ 0.850637] mvneta f1034000.ethernet eth1: Using random mac address c6:31:9b:9c:a7:67
[ 0.859250] mvneta f1070000.ethernet eth2: Using hardware mac address 00:50:43:ee:18:3b
[ 0.867330] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.873879] ehci-pci: EHCI PCI platform driver
[ 0.878359] ehci-platform: EHCI generic platform driver
[ 0.883691] ehci-orion: EHCI orion driver
[ 0.887777] orion-ehci f1058000.usb: EHCI Host Controller
[ 0.893203] orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1
[ 0.900847] orion-ehci f1058000.usb: irq 40, io mem 0xf1058000
[ 0.921501] orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00
[ 0.927667] hub 1-0:1.0: USB hub found
[ 0.931437] hub 1-0:1.0: 1 port detected
[ 0.935663] xhci-hcd f10f0000.usb3: xHCI Host Controller
[ 0.940994] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2
[ 0.948605] xhci-hcd f10f0000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x00010010
[ 0.957170] xhci-hcd f10f0000.usb3: irq 48, io mem 0xf10f0000
[ 0.963146] hub 2-0:1.0: USB hub found
[ 0.966914] hub 2-0:1.0: 1 port detected
[ 0.970927] xhci-hcd f10f0000.usb3: xHCI Host Controller
[ 0.976265] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3
[ 0.983796] usb usb3: We dont know the algorithms for LPM for this host, disabling LPM.
[ 0.992105] hub 3-0:1.0: USB hub found
[ 0.995872] hub 3-0:1.0: 1 port detected
[ 0.999930] xhci-hcd f10f8000.usb3: xHCI Host Controller
[ 1.005271] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4
[ 1.012863] xhci-hcd f10f8000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x00010010
[ 1.021422] xhci-hcd f10f8000.usb3: irq 49, io mem 0xf10f8000
[ 1.027391] hub 4-0:1.0: USB hub found
[ 1.031159] hub 4-0:1.0: 1 port detected
[ 1.035201] xhci-hcd f10f8000.usb3: xHCI Host Controller
[ 1.040528] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5
[ 1.048072] usb usb5: We dont know the algorithms for LPM for this host, disabling LPM.
[ 1.056389] hub 5-0:1.0: USB hub found
[ 1.060156] hub 5-0:1.0: 1 port detected
[ 1.064290] usbcore: registered new interface driver usb-storage
[ 1.070460] armada38x-rtc f10a3800.rtc: rtc core: registered f10a3800.rtc as rtc0
[ 1.078105] i2c /dev entries driver
[ 1.092469] orion_wdt: Initial timeout 171 sec
[ 1.097786] marvell-cesa f1090000.crypto: CESA device successfully registered
[ 1.105445] NET: Registered protocol family 10
[ 1.110382] NET: Registered protocol family 17
[ 1.114870] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 1.127526] Bridge firewalling registered
[ 1.131551] 8021q: 802.1Q VLAN Support v1.8
[ 1.135771] Registering SWP/SWPB emulation handler
[ 1.141319] armada38x-rtc f10a3800.rtc: setting system clock to 1970-06-02 16:51:43 UTC (13193503)
[ 1.141517] ata1: SATA link down (SStatus 0 SControl 300)
[ 1.141542] ata2: SATA link down (SStatus 0 SControl 300)
[ 1.161504] ata4: SATA link down (SStatus 0 SControl 300)
[ 1.166942] ata3: SATA link down (SStatus 0 SControl 300)
[ 1.172389] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6
[ 1.179889] Please append a correct "root=" boot option; here are the available partitions:
[ 1.188270] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[ 1.196553] CPU1: stopping
[ 1.199266] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.4.14 #1
[ 1.205198] Hardware name: Marvell Armada 380/385 (Device Tree)
[ 1.211142] [<c001fab8>] (unwind_backtrace) from [<c001c420>] (show_stack+0x10/0x14)
[ 1.218909] [<c001c420>] (show_stack) from [<c019f54c>] (dump_stack+0x8c/0xa0)
[ 1.226149] [<c019f54c>] (dump_stack) from [<c001e94c>] (handle_IPI+0x108/0x1a0)
[ 1.233563] [<c001e94c>] (handle_IPI) from [<c0009508>] (gic_handle_irq+0x80/0x94)
[ 1.241151] [<c0009508>] (gic_handle_irq) from [<c000a5f4>] (__irq_svc+0x54/0x70)
[ 1.248650] Exception stack(0xef073f80 to 0xef073fc8)
[ 1.253712] 3f80: 00000001 00000000 00000000 c000b3c0 ef072000 c05f6498 c04fcab4 00000000
[ 1.261909] 3fa0: c05ee224 ef073fd8 00000000 c05f1118 00000000 ef073fd0 c00194cc c00194d0
[ 1.270104] 3fc0: 60000013 ffffffff
[ 1.273600] [<c000a5f4>] (__irq_svc) from [<c00194d0>] (arch_cpu_idle+0x34/0x50)
[ 1.281015] [<c00194d0>] (arch_cpu_idle) from [<c005b324>] (cpu_startup_entry+0x148/0x210)
[ 1.289298] [<c005b324>] (cpu_startup_entry) from [<000095ac>] (0x95ac)
[ 1.295928] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
Current OpenWrt CC initramfs freezes upon loading the kernel (Compiled 2018.01.27)
Marvell>> tftpboot openwrt-mvebu-armada-388-clearfog-initramfs
Using egiga1 device
TFTP from server 10.4.50.38; our IP address is 10.4.50.170
Filename 'openwrt-mvebu-armada-388-clearfog-initramfs'.
Load address: 0x2000000
Loading: #################################################################
#################################################################
#################################################################
2.4 MiB/s
done
Bytes transferred = 7925725 (78efdd hex)
Marvell>> bootm
## Booting kernel from Legacy Image at 02000000 ...
Image Name: ARM OpenWrt Linux-3.18.91
Created: 2018-01-27 3:22:24 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 7925661 Bytes = 7.6 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Expected Output (working initramfs)
r48735 (Compiled 2016.02.17)
Marvell>> tftpboot openwrt-mvebu-armada-388-clearfog-initramfs
Using egiga1 device
TFTP from server 10.4.50.38; our IP address is 10.4.50.170
Filename 'openwrt-mvebu-armada-388-clearfog-initramfs'.
Load address: 0x2000000
Loading: #################################################################
#################################################################
#################################################################
2.4 MiB/s
done
Bytes transferred = 3022310 (2e1de6 hex)
Marvell>> bootm
## Booting kernel from Legacy Image at 02000000 ...
Image Name: ARM OpenWrt Linux-4.1.16
Created: 2016-02-17 14:26:46 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3022246 Bytes = 2.9 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.1.16 (vlado@b50) (gcc version 5.2.0 (OpenWrt GCC 5.2.0 r48723) ) #6 SMP Wed Feb 17 14:59:16 UTC 2016
[ 0.000000] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: SolidRun Clearfog A1
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] PERCPU: Embedded 10 pages/cpu @eefd1000 s11776 r8192 d20992 u40960
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260624
[ 0.000000] Kernel command line:
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 1029820K/1048576K available (3435K kernel code, 138K rwdata, 1228K rodata, 4592K init, 168K bss, 18756K reserved, 0K cma-reserved, 270336K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xef800000 ( 760 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0495e9c (4664 kB)
[ 0.000000] .init : 0xc0496000 - 0xc0912000 (4592 kB)
[ 0.000000] .data : 0xc0912000 - 0xc09348dc ( 139 kB)
[ 0.000000] .bss : 0xc09348dc - 0xc095e9a4 ( 169 kB)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] mvebu_mbus: [Firmware Warn]: deprecated mbus-mvebu Device Tree, suspend/resume will not work
[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9
[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9
[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled
[ 0.000000] L2C-310 Coherent cache controller enabled, 16 ways, 1024 kB
[ 0.000000] L2C-310 Coherent: CACHE_ID 0x410054c9, AUX_CTRL 0x46070001
[ 0.000006] sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 85899345900ns
[ 0.000016] clocksource armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns
[ 0.000157] Calibrating delay loop... 3188.32 BogoMIPS (lpj=15941632)
[ 0.059922] pid_max: default: 32768 minimum: 301
[ 0.059975] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.059980] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.060187] CPU: Testing write buffer coherency: ok
[ 0.060286] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.060311] Setting up static identity map for 0x8280 - 0x82d8
[ 0.060398] mvebu-soc-id: MVEBU SoC ID=0x6828, Rev=0x4
[ 0.060484] mvebu-pmsu: Initializing Power Management Service Unit
[ 0.060915] Booting CPU 1
[ 0.119940] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.119969] Brought up 2 CPUs
[ 0.119975] SMP: Total of 2 processors activated (6384.02 BogoMIPS).
[ 0.119978] CPU: All CPU(s) started in SVC mode.
[ 0.121764] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 0.121843] clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.121875] pinctrl core: initialized pinctrl subsystem
[ 0.122216] NET: Registered protocol family 16
[ 0.122655] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.149929] cpuidle: using governor ladder
[ 0.152518] mvebu-pmsu: CPU hotplug support is currently broken on Armada 38x: disabling
[ 0.152527] mvebu-pmsu: CPU idle is currently broken on Armada 38x: disabling[ 0.180892] Switched to clocksource armada_370_xp_clocksource
[ 0.181354] NET: Registered protocol family 2
[ 0.181626] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.181665] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.181728] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.181766] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.181790] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.181897] NET: Registered protocol family 1
[ 0.202800] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.203086] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.203094] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.203620] bounce: pool size: 64 pages
[ 0.203629] io scheduler noop registered
[ 0.203635] io scheduler deadline registered (default)
[ 0.204062] armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver
[ 0.204398] irq: Cannot allocate irq_descs @ IRQ48, assuming pre-allocated
[ 0.204557] irq: Cannot allocate irq_descs @ IRQ80, assuming pre-allocated
[ 0.204865] mvebu-pcie soc:pcie-controller: PCI host bridge to bus 0000:00
[ 0.204873] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff]
[ 0.204878] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff]
[ 0.204883] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.205081] PCI: bus0: Fast back to back transfers disabled
[ 0.205087] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.205094] pci 0000:00:03.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.205147] PCI: bus1: Fast back to back transfers enabled
[ 0.205205] PCI: bus2: Fast back to back transfers enabled
[ 0.205227] pci 0000:00:02.0: PCI bridge to [bus 01]
[ 0.205235] pci 0000:00:03.0: PCI bridge to [bus 02]
[ 0.205319] mv_xor f1060800.xor: Marvell shared XOR driver
[ 0.240922] mv_xor f1060800.xor: Marvell XOR: ( xor cpy )
[ 0.280920] mv_xor f1060800.xor: Marvell XOR: ( xor cpy )
[ 0.280980] mv_xor f1060900.xor: Marvell shared XOR driver
[ 0.320931] mv_xor f1060900.xor: Marvell XOR: ( xor cpy )
[ 0.360921] mv_xor f1060900.xor: Marvell XOR: ( xor cpy )
[ 0.361040] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.361326] console [ttyS0] disabled
[ 0.381355] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 23, base_baud = 15625000) is a 16550A
[ 0.965181] console [ttyS0] enabled
[ 0.988835] f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 24, base_baud = 15625000) is a 16550A
[ 0.998710] libphy: Fixed MDIO Bus: probed
[ 1.002938] libphy: orion_mdio_bus: probed
[ 1.008077] mvneta f1030000.ethernet eth0: Using hardware mac address 00:50:43:11:03:0d
[ 1.016851] mvneta f1034000.ethernet eth1: Using random mac address fa:fb:df:f9:5e:cc
[ 1.025385] mvneta f1070000.ethernet eth2: Using hardware mac address 00:50:43:0b:03:0d
[ 1.033899] NET: Registered protocol family 10
[ 1.038792] NET: Registered protocol family 17
[ 1.043270] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 1.055917] 8021q: 802.1Q VLAN Support v1.8
[ 1.060127] Registering SWP/SWPB emulation handler
[ 1.065542] hctosys: unable to open rtc device (rtc0)
[ 1.073694] Freeing unused kernel memory: 4592K (c0496000 - c0912000)
[ 1.084136] init: Console is alive
[ 1.092498] usbcore: registered new interface driver usbfs
[ 1.098025] usbcore: registered new interface driver hub
[ 1.103400] usbcore: registered new device driver usb
[ 1.110084] SCSI subsystem initialized
[ 1.114896] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.121693] ehci-platform: EHCI generic platform driver
[ 1.127263] ehci-orion: EHCI orion driver
[ 1.131413] orion-ehci f1058000.usb: EHCI Host Controller
[ 1.136834] orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1
[ 1.144492] orion-ehci f1058000.usb: irq 40, io mem 0xf1058000
[ 1.160910] orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00
[ 1.167093] hub 1-0:1.0: USB hub found
[ 1.170862] hub 1-0:1.0: 1 port detected
[ 1.179139] xhci-hcd f10f0000.usb3: xHCI Host Controller
[ 1.184488] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2
[ 1.192080] xhci-hcd f10f0000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x00010010
[ 1.200644] xhci-hcd f10f0000.usb3: irq 46, io mem 0xf10f0000
[ 1.206652] hub 2-0:1.0: USB hub found
[ 1.210421] hub 2-0:1.0: 1 port detected
[ 1.214450] xhci-hcd f10f0000.usb3: xHCI Host Controller
[ 1.219779] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3
[ 1.227335] usb usb3: We dont know the algorithms for LPM for this host, disabling LPM.
[ 1.235651] hub 3-0:1.0: USB hub found
[ 1.239417] hub 3-0:1.0: 1 port detected
[ 1.243492] xhci-hcd f10f8000.usb3: xHCI Host Controller
[ 1.248823] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4
[ 1.256412] xhci-hcd f10f8000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x00010010
[ 1.264975] xhci-hcd f10f8000.usb3: irq 47, io mem 0xf10f8000
[ 1.270975] hub 4-0:1.0: USB hub found
[ 1.274743] hub 4-0:1.0: 1 port detected
[ 1.278759] xhci-hcd f10f8000.usb3: xHCI Host Controller
[ 1.284092] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5
[ 1.291620] usb usb5: We dont know the algorithms for LPM for this host, disabling LPM.
[ 1.299925] hub 5-0:1.0: USB hub found
[ 1.303697] hub 5-0:1.0: 1 port detected
[ 1.308557] usbcore: registered new interface driver usb-storage
[ 2.087795] init: - preinit -
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 5.131673] procd: - early -
[ 5.706452] procd: - ubus -
[ 6.710759] random: ubusd urandom read with 0 bits of entropy available
[ 6.717649] procd: - init -
Please press Enter to activate this console.
[ 6.863841] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 6.871496] i2c /dev entries driver
[ 6.876831] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 6.884031] nf_conntrack version 0.5.0 (16162 buckets, 64648 max)
[ 7.074295] xt_time: kernel timezone is -0000
[ 7.091235] PPP generic driver version 2.4.2
[ 7.095849] NET: Registered protocol family 24
[ 8.723584] device eth0 entered promiscuous mode
[ 8.728953] br-lan: port 1(eth0) entered forwarding state
[ 8.734388] br-lan: port 1(eth0) entered forwarding state
[ 8.751499] device eth1 entered promiscuous mode
[ 8.756174] br-lan: port 2(eth1) entered forwarding state
[ 8.761615] br-lan: port 2(eth1) entered forwarding state
[ 8.781126] IPv6: ADDRCONF(NETDEV_UP): eth2: link is not ready
[ 9.720913] br-lan: port 1(eth0) entered disabled state
[ 9.726221] br-lan: port 2(eth1) entered disabled state
[ 10.730912] mvneta f1030000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[ 10.738772] br-lan: port 1(eth0) entered forwarding state
[ 10.744197] br-lan: port 1(eth0) entered forwarding state
[ 10.750020] mvneta f1034000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[ 10.757942] br-lan: port 2(eth1) entered forwarding state
[ 10.763366] br-lan: port 2(eth1) entered forwarding state
[ 12.740888] br-lan: port 1(eth0) entered forwarding state
[ 12.760887] br-lan: port 2(eth1) entered forwarding state
BusyBox v1.24.1 () built-in shell (ash)
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
DESIGNATED DRIVER (Bleeding Edge, r48735)
-----------------------------------------------------
* 2 oz. Orange Juice Combine all juices in a
* 2 oz. Pineapple Juice tall glass filled with
* 2 oz. Grapefruit Juice ice, stir well.
* 2 oz. Cranberry Juice
-----------------------------------------------------
root@OpenWrt:/#
r49395 (Compiled 2018.01.27 | Xue Liuās OpenWrt Repo)
Marvell>> tftpboot openwrt-mvebu-armada-388-clearfog-initramfs
Using egiga1 device
TFTP from server 10.4.50.38; our IP address is 10.4.50.170
Filename 'openwrt-mvebu-armada-388-clearfog-initramfs'.
Load address: 0x2000000
Loading: #################################################################
#################################################################
#################################################################
2.4 MiB/s
done
Bytes transferred = 3920894 (3bd3fe hex)
Marvell>> bootm
## Booting kernel from Legacy Image at 02000000 ...
Image Name: ARM OpenWrt Linux-4.1.23
Created: 2016-06-30 5:39:05 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3920830 Bytes = 3.7 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.1.23 (jw@u17) (gcc version 5.3.0 (OpenWrt GCC 5.3.0 r49395) ) #2 SMP Sat Jan 27 05:52:51 UTC 2018
[ 0.000000] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: SolidRun Clearfog A1
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] PERCPU: Embedded 10 pages/cpu @eefd1000 s11776 r8192 d20992 u40960
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260624
[ 0.000000] Kernel command line:
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 1026868K/1048576K available (3435K kernel code, 138K rwdata, 1228K rodata, 7544K init, 168K bss, 21708K reserved, 0K cma-reserved, 270336K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xef800000 ( 760 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0495e9c (4664 kB)
[ 0.000000] .init : 0xc0496000 - 0xc0bf4000 (7544 kB)
[ 0.000000] .data : 0xc0bf4000 - 0xc0c1694c ( 139 kB)
[ 0.000000] .bss : 0xc0c1694c - 0xc0c40a24 ( 169 kB)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] mvebu_mbus: [Firmware Warn]: deprecated mbus-mvebu Device Tree, suspend/resume will not work
[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9
[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9
[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled
[ 0.000000] L2C-310 Coherent cache controller enabled, 16 ways, 1024 kB
[ 0.000000] L2C-310 Coherent: CACHE_ID 0x410054c9, AUX_CTRL 0x46070001
[ 0.000006] sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 85899345900ns
[ 0.000016] clocksource armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns
[ 0.000156] Calibrating delay loop... 3188.32 BogoMIPS (lpj=15941632)
[ 0.059921] pid_max: default: 32768 minimum: 301
[ 0.059975] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.059980] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.060187] CPU: Testing write buffer coherency: ok
[ 0.060287] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.060312] Setting up static identity map for 0x8280 - 0x82d8
[ 0.060399] mvebu-soc-id: MVEBU SoC ID=0x6828, Rev=0x4
[ 0.060486] mvebu-pmsu: Initializing Power Management Service Unit
[ 0.060919] Booting CPU 1
[ 0.119939] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.119968] Brought up 2 CPUs
[ 0.119974] SMP: Total of 2 processors activated (6384.02 BogoMIPS).
[ 0.119977] CPU: All CPU(s) started in SVC mode.
[ 0.121712] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 0.121790] clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.121823] pinctrl core: initialized pinctrl subsystem
[ 0.122159] NET: Registered protocol family 16
[ 0.122595] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.149921] cpuidle: using governor ladder
[ 0.152478] mvebu-pmsu: CPU hotplug support is currently broken on Armada 38x: disabling
[ 0.152487] mvebu-pmsu: CPU idle is currently broken on Armada 38x: disabling[ 0.180937] Switched to clocksource armada_370_xp_clocksource
[ 0.181394] NET: Registered protocol family 2
[ 0.181808] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.181846] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.181909] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.181945] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.181969] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.182064] NET: Registered protocol family 1
[ 0.211472] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.211907] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.211916] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.212261] bounce: pool size: 64 pages
[ 0.212269] io scheduler noop registered
[ 0.212276] io scheduler deadline registered (default)
[ 0.212708] armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver
[ 0.213051] irq: Cannot allocate irq_descs @ IRQ48, assuming pre-allocated
[ 0.213206] irq: Cannot allocate irq_descs @ IRQ80, assuming pre-allocated
[ 0.213509] mvebu-pcie soc:pcie-controller: PCI host bridge to bus 0000:00
[ 0.213517] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff]
[ 0.213525] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff]
[ 0.213531] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.213721] PCI: bus0: Fast back to back transfers disabled
[ 0.213728] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.213734] pci 0000:00:03.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.213786] PCI: bus1: Fast back to back transfers enabled
[ 0.213847] PCI: bus2: Fast back to back transfers enabled
[ 0.213868] pci 0000:00:02.0: PCI bridge to [bus 01]
[ 0.213876] pci 0000:00:03.0: PCI bridge to [bus 02]
[ 0.213955] mv_xor f1060800.xor: Marvell shared XOR driver
[ 0.251038] mv_xor f1060800.xor: Marvell XOR: ( xor cpy )
[ 0.290970] mv_xor f1060800.xor: Marvell XOR: ( xor cpy )
[ 0.291030] mv_xor f1060900.xor: Marvell shared XOR driver
[ 0.330964] mv_xor f1060900.xor: Marvell XOR: ( xor cpy )
[ 0.370964] mv_xor f1060900.xor: Marvell XOR: ( xor cpy )
[ 0.371073] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.371364] console [ttyS0] disabled
[ 0.391394] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 23, base_baud = 15625000) is a 16550A
[ 0.974982] console [ttyS0] enabled
[ 0.998634] f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 24, base_baud = 15625000) is a 16550A
[ 1.008502] libphy: Fixed MDIO Bus: probed
[ 1.012730] libphy: orion_mdio_bus: probed
[ 1.017876] mvneta f1030000.ethernet eth0: Using hardware mac address 00:50:43:5a:07:04
[ 1.026640] mvneta f1034000.ethernet eth1: Using random mac address d6:15:0c:61:68:d9
[ 1.035175] mvneta f1070000.ethernet eth2: Using hardware mac address 00:50:43:0a:07:04
[ 1.043675] NET: Registered protocol family 10
[ 1.048569] NET: Registered protocol family 17
[ 1.053061] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 1.065708] 8021q: 802.1Q VLAN Support v1.8
[ 1.069920] Registering SWP/SWPB emulation handler
[ 1.075317] hctosys: unable to open rtc device (rtc0)
[ 1.084968] Freeing unused kernel memory: 7544K (c0496000 - c0bf4000)
[ 1.095444] init: Console is alive
[ 1.105049] usbcore: registered new interface driver usbfs
[ 1.110581] usbcore: registered new interface driver hub
[ 1.115954] usbcore: registered new device driver usb
[ 1.126902] SCSI subsystem initialized
[ 1.131749] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.138544] ehci-platform: EHCI generic platform driver
[ 1.144141] ehci-orion: EHCI orion driver
[ 1.148257] orion-ehci f1058000.usb: EHCI Host Controller
[ 1.153689] orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1
[ 1.161343] orion-ehci f1058000.usb: irq 40, io mem 0xf1058000
[ 1.180940] orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00
[ 1.187137] hub 1-0:1.0: USB hub found
[ 1.190909] hub 1-0:1.0: 1 port detected
[ 1.199341] xhci-hcd f10f0000.usb3: xHCI Host Controller
[ 1.204699] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2
[ 1.212291] xhci-hcd f10f0000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x00010010
[ 1.220854] xhci-hcd f10f0000.usb3: irq 46, io mem 0xf10f0000
[ 1.226864] hub 2-0:1.0: USB hub found
[ 1.230634] hub 2-0:1.0: 1 port detected
[ 1.234670] xhci-hcd f10f0000.usb3: xHCI Host Controller
[ 1.239997] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3
[ 1.247530] usb usb3: We dont know the algorithms for LPM for this host, disabling LPM.
[ 1.255845] hub 3-0:1.0: USB hub found
[ 1.259613] hub 3-0:1.0: 1 port detected
[ 1.263710] xhci-hcd f10f8000.usb3: xHCI Host Controller
[ 1.269041] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4
[ 1.276630] xhci-hcd f10f8000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x00010010
[ 1.285195] xhci-hcd f10f8000.usb3: irq 47, io mem 0xf10f8000
[ 1.291190] hub 4-0:1.0: USB hub found
[ 1.294958] hub 4-0:1.0: 1 port detected
[ 1.298974] xhci-hcd f10f8000.usb3: xHCI Host Controller
[ 1.304309] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5
[ 1.311842] usb usb5: We dont know the algorithms for LPM for this host, disabling LPM.
[ 1.320147] hub 5-0:1.0: USB hub found
[ 1.323921] hub 5-0:1.0: 1 port detected
[ 1.329839] sdhci: Secure Digital Host Controller Interface driver
[ 1.336054] sdhci: Copyright(c) Pierre Ossman
[ 1.340684] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.347178] usbcore: registered new interface driver usb-storage
[ 1.360572] init: - preinit -
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 4.406424] procd: - early -
[ 4.965685] procd: - ubus -
[ 5.019086] random: ubusd urandom read with 0 bits of entropy available
[ 5.025976] procd: - init -
Please press Enter to activate this console.
[ 5.196134] device-mapper: ioctl: 4.31.0-ioctl (2015-3-12) initialised: dm-devel@redhat.com
[ 5.207844] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 5.215742] i2c /dev entries driver
[ 5.221208] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 5.228628] nf_conntrack version 0.5.0 (16162 buckets, 64648 max)
[ 5.414558] xt_time: kernel timezone is -0000
[ 5.431616] PPP generic driver version 2.4.2
[ 5.436259] NET: Registered protocol family 24
[ 7.114973] device eth0 entered promiscuous mode
[ 7.122099] br-lan: port 1(eth0) entered forwarding state
[ 7.127527] br-lan: port 1(eth0) entered forwarding state
[ 7.148077] device eth1 entered promiscuous mode
[ 7.152853] br-lan: port 2(eth1) entered forwarding state
[ 7.158270] br-lan: port 2(eth1) entered forwarding state
[ 7.173015] IPv6: ADDRCONF(NETDEV_UP): eth2: link is not ready
[ 8.110954] br-lan: port 1(eth0) entered disabled state
[ 8.116262] br-lan: port 2(eth1) entered disabled state
[ 9.120956] mvneta f1030000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[ 9.128814] br-lan: port 1(eth0) entered forwarding state
[ 9.134240] br-lan: port 1(eth0) entered forwarding state
[ 9.140957] mvneta f1034000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[ 9.148813] br-lan: port 2(eth1) entered forwarding state
[ 9.154235] br-lan: port 2(eth1) entered forwarding state
[ 11.130932] br-lan: port 1(eth0) entered forwarding state
[ 11.150930] br-lan: port 2(eth1) entered forwarding state
BusyBox v1.24.2 () built-in shell (ash)
Enter 'help' for a list of built-in commands.
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
DESIGNATED DRIVER (Bleeding Edge, r49395)
-----------------------------------------------------
* 2 oz. Orange Juice Combine all juices in a
* 2 oz. Pineapple Juice tall glass filled with
* 2 oz. Grapefruit Juice ice, stir well.
* 2 oz. Cranberry Juice
-----------------------------------------------------
root@OpenWrt:/#
|
|
09.03.2018 | 1418 | Base system | Bug Report | Very Low | Critical | DHCP not discovering certain devices on radio1 (2.4ghz ... | Trunk | Unconfirmed |
Task Description
Supply the following if possible: - Device problem occurs on
Linksys 3200ACM
- Software versions of OpenWrt/LEDE release, packages, etc.
OpenWrt SNAPSHOT r6365-45fdb12 / LuCI Master (git-18.061.42275-852ec6e)
Additional Packages:
openssh-sftp-server 7.6p1-1
nginx 1.12.2-1
- Steps to reproduce
Embedded platform such ESP8266, Wireless Cameras are unable to connect
to 2.4Ghz radio1 on 3200ACM with WPA2-CCMP.
DHCP does not seem to discover these devices although radio1 (mwlwifi) successfully
authenticates the devices.
Clients: 4 x ESP8266 (SonOff Switches, FluxLED, etc.), Unbranded Wireless Camera
DHCP Configuration
config dnsmasq
option domainneeded '1'
option localise_queries '1'
option rebind_protection '1'
option rebind_localhost '1'
option local '/lan/'
option domain 'lan'
option expandhosts '1'
option authoritative '1'
option readethers '1'
option leasefile '/tmp/dhcp.leases'
option resolvfile '/tmp/resolv.conf.auto'
option nonwildcard '1'
option localservice '1'
config dhcp 'lan'
option interface 'lan'
option start '100'
option limit '150'
option leasetime '12h'
list dhcp_option '6,8.8.8.8,8.8.4.4'
config dhcp 'wan'
option interface 'wan'
option ignore '1'
config odhcpd 'odhcpd'
option maindhcp '0'
option leasefile '/tmp/hosts/odhcpd'
option leasetrigger '/usr/sbin/odhcpd-update'
option loglevel '4'
config host
option name 'VelopNode1'
option dns '1'
option mac '58:ef:xx:xx:xx:xx'
option ip '192.168.1.151'
option leasetime 'infinite'
config host
option name 'Hikam-0505'
option dns '1'
option mac '88:83:5d:xx:xx:xx'
option ip '192.168.1.200'
option leasetime 'infinite'
config host
option name 'ESP_C0F513'
option dns '1'
option mac 'dc:4f:22:xx:xx:xx'
option ip '192.168.1.235'
option leasetime 'infinite'
2.4Ghz radio1 configuration:
wireless.radio1=wifi-device
wireless.radio1.type='mac80211'
wireless.radio1.hwmode='11g'
wireless.radio1.path='soc/soc:pcie/pci0000:00/0000:00:02.0/0000:02:00.0'
wireless.radio1.country='US'
wireless.radio1.channel='11'
wireless.radio1.htmode='HT20'
wireless.radio1.legacy_rates='1'
wireless.radio1.txpower='30'
root@openwrt:~# uci show wireless.default_radio1
wireless.default_radio1=wifi-iface
wireless.default_radio1.device='radio1'
wireless.default_radio1.network='lan'
wireless.default_radio1.ssid='SSID'
wireless.default_radio1.key='PASSWORD'
wireless.default_radio1.mode='ap'
wireless.default_radio1.encryption='psk2'
- Logs:
Sun Mar 4 04:07:41 2018 daemon.notice hostapd: wlan1: AP-STA-CONNECTED dc:4f:22:xx:xx:xx
Sun Mar 4 04:07:41 2018 daemon.info hostapd: wlan1: STA dc:4f:22:xx:xx:xx WPA: pairwise key handshake completed (RSN)
Sun Mar 4 04:07:50 2018 authpriv.info dropbear[3371]: Child connection from 192.168.1.151:57119
Sun Mar 4 04:08:07 2018 daemon.notice hostapd: wlan1: AP-STA-DISCONNECTED dc:4f:22:xx:xx:xx
Sun Mar 4 04:08:07 2018 daemon.info hostapd: wlan1: STA dc:4f:22:xx:xx:xx IEEE 802.11: disassociated
Sun Mar 4 04:08:07 2018 kern.debug kernel: [ 105.684705] ieee80211 phy1: staid 3 deleted
Sun Mar 4 04:08:08 2018 daemon.info hostapd: wlan1: STA dc:4f:22:xx:xx:xx IEEE 802.11: deauthenticated due to inactivity (timer DEAUTH/REMOVE)
Sun Mar 4 04:08:10 2018 kern.debug kernel: [ 107.923936] ieee80211 phy1: staid 2 deleted
Sun Mar 4 04:08:10 2018 daemon.info hostapd: wlan1: STA dc:4f:22:xx:xx:xx IEEE 802.11: associated (aid 2)
Sun Mar 4 04:08:10 2018 daemon.notice hostapd: wlan1: AP-STA-CONNECTED dc:4f:22:xx:xx:xx
Sun Mar 4 04:08:10 2018 daemon.info hostapd: wlan1: STA dc:4f:22:xx:xx:xx WPA: pairwise key handshake completed (RSN)
Sun Mar 4 04:08:13 2018 daemon.info hostapd: wlan1: STA dc:4f:22:xx:xx:xx IEEE 802.11: associated (aid 3)
Sun Mar 4 04:08:13 2018 daemon.notice hostapd: wlan1: AP-STA-CONNECTED dc:4f:22:xx:xx:xx
Sun Mar 4 04:08:13 2018 daemon.info hostapd: wlan1: STA dc:4f:22:xx:xx:xx WPA: pairwise key handshake completed (RSN)
Sun Mar 4 04:08:26 2018 daemon.info hostapd: wlan1: STA dc:4f:22:xx:xx:xx IEEE 802.11: authenticated
Sun Mar 4 04:08:26 2018 daemon.info hostapd: wlan1: STA dc:4f:22:xx:xx:xx IEEE 802.11: authenticated
Sun Mar 4 04:08:26 2018 daemon.info hostapd: wlan1: STA dc:4f:22:xx:xx:xx IEEE 802.11: authenticated
Sun Mar 4 04:08:26 2018 daemon.info hostapd: wlan1: STA dc:4f:22:xx:xx:xx IEEE 802.11: authenticated
Sun Mar 4 04:08:44 2018 kern.debug kernel: [ 141.932637] ieee80211 phy1: staid 2 deleted
Sun Mar 4 04:08:44 2018 daemon.info hostapd: wlan1: STA dc:4f:22:xx:xx:xx IEEE 802.11: associated (aid 2)
Sun Mar 4 04:08:44 2018 daemon.notice hostapd: wlan1: AP-STA-CONNECTED dc:4f:22:xx:xx:xx
Sun Mar 4 04:08:44 2018 daemon.info hostapd: wlan1: STA dc:4f:22:xx:xx:xx WPA: pairwise key handshake completed (RSN)
Sun Mar 4 04:08:44 2018 kern.debug kernel: [ 142.629431] ieee80211 phy1: staid 3 deleted
Sun Mar 4 04:08:48 2018 daemon.info hostapd: wlan1: STA dc:4f:22:xx:xx:xx IEEE 802.11: associated (aid 3)
Sun Mar 4 04:08:48 2018 daemon.notice hostapd: wlan1: AP-STA-CONNECTED dc:4f:22:xx:xx:xx
Sun Mar 4 04:08:48 2018 daemon.info hostapd: wlan1: STA dc:4f:22:xx:xx:xx WPA: pairwise key handshake completed (RSN)
Sun Mar 4 04:09:22 2018 kern.debug kernel: [ 180.723186] ieee80211 phy1: staid 3 deleted
Sun Mar 4 04:09:22 2018 daemon.info hostapd: wlan1: STA dc:4f:22:xx:xx:xx IEEE 802.11: associated (aid 3)
Sun Mar 4 04:09:23 2018 kern.debug kernel: [ 181.044324] ieee80211 phy1: staid 2 deleted
Sun Mar 4 04:09:23 2018 daemon.info hostapd: wlan1: STA dc:4f:22:xx:xx:xx IEEE 802.11: associated (aid 2)
Sun Mar 4 04:09:23 2018 daemon.notice hostapd: wlan1: AP-STA-CONNECTED dc:4f:22:xx:xx:xx
Sun Mar 4 04:09:23 2018 daemon.info hostapd: wlan1: STA dc:4f:22:xx:xx:xx WPA: pairwise key handshake completed (RSN)
Sun Mar 4 04:09:26 2018 kern.debug kernel: [ 184.838938] ieee80211 phy1: staid 3 deleted
Sun Mar 4 04:09:26 2018 daemon.info hostapd: wlan1: STA dc:4f:22:xx:xx:xx IEEE 802.11: associated (aid 3)
Sun Mar 4 04:09:28 2018 daemon.notice hostapd: wlan1: AP-STA-CONNECTED dc:4f:22:xx:xx:xx
Sun Mar 4 04:09:28 2018 daemon.info hostapd: wlan1: STA dc:4f:22:xx:xx:xx WPA: pairwise key handshake completed (RSN)
Sun Mar 4 04:09:34 2018 daemon.info hostapd: wlan1: STA dc:4f:22:xx:xx:xx IEEE 802.11: authenticated
Sun Mar 4 04:09:34 2018 daemon.info hostapd: wlan1: STA dc:4f:22:xx:xx:xx IEEE 802.11: authenticated
Sun Mar 4 04:09:34 2018 daemon.info hostapd: wlan1: STA dc:4f:22:xx:xx:xx IEEE 802.11: authenticated
Sun Mar 4 04:09:34 2018 daemon.info hostapd: wlan1: STA dc:4f:22:xx:xx:xx IEEE 802.11: authenticated
Sun Mar 4 04:09:34 2018 daemon.info hostapd: wlan1: STA dc:4f:22:xx:xx:xx IEEE 802.11: authenticated
Sun Mar 4 04:09:34 2018 kern.debug kernel: [ 191.989466] ieee80211 phy1: staid 3 deleted
Sun Mar 4 04:09:34 2018 daemon.info hostapd: wlan1: STA dc:4f:22:xx:xx:xx IEEE 802.11: authenticated
Sun Mar 4 04:10:06 2018 daemon.info hostapd: wlan1: STA dc:4f:22:xx:xx:xx IEEE 802.11: associated (aid 3)
Sun Mar 4 04:10:06 2018 daemon.notice hostapd: wlan1: AP-STA-CONNECTED dc:4f:22:xx:xx:xx
Sun Mar 4 04:10:06 2018 daemon.info hostapd: wlan1: STA dc:4f:22:xx:xx:xx WPA: pairwise key handshake completed (RSN)
Sun Mar 4 04:10:07 2018 kern.debug kernel: [ 225.251038] ieee80211 phy1: staid 2 deleted
Sun Mar 4 04:10:07 2018 daemon.info hostapd: wlan1: STA dc:4f:22:xx:xx:xx IEEE 802.11: associated (aid 2)
Sun Mar 4 04:10:07 2018 daemon.notice hostapd: wlan1: AP-STA-CONNECTED dc:4f:22:xx:xx:xx
Sun Mar 4 04:10:07 2018 daemon.info hostapd: wlan1: STA dc:4f:22:xx:xx:xx WPA: pairwise key handshake completed (RSN)
Note: These clients are able to join my alternative access point (Velop Nodes) on same frequency and encryption. They are also
able to join on factory image(FW_WRT3200ACM_1.0.6.186168_prod) radio1 access point and as well as radio2 in openwrt stipulated build.
More info: https://github.com/kaloz/mwlwifi/issues/278
|
|
16.05.2018 | 1550 | Base system | Bug Report | Very Low | Critical | Unable to handle kernel paging request causes router to... | Trunk | Unconfirmed |
Task Description
- Device problem occurs on Xiaomi mi router 3G (R3G)
- Software versions of OpenWrt/LEDE release, packages, etc. Latest trunk (r6893-bfbdeeb) custom build
- Steps to reproduce Did not notice there is a pattern here.
- The issue The kernel crash causes the router to reboot. Here are two traces I was able to catch
May 13 07:24:52 router kernel: [82948.434471] CPU 1 Unable to handle kernel paging request at virtual address 07407800, epc == 80136a70, ra == 8013694c May 13 07:24:52 router kernel: [82948.445103] Oops[#1]: May 13 07:24:52 router kernel: [82948.447387] CPU: 1 PID: 1977 Comm: kworker/u8:1 Not tainted 4.14.37 #0 May 13 07:24:52 router kernel: [82948.453909] Workqueue: writeback wb_workfn (flush-8:0) May 13 07:24:52 router kernel: [82948.459046] task: 8ff3ddc0 task.stack: 8dd62000 May 13 07:24:52 router kernel: [82948.463565] $ 0 : 00000000 00000001 00000000 812286b0 May 13 07:24:52 router kernel: [82948.468800] $ 4 : 805aa44c 00000001 00000001 07407800 May 13 07:24:52 router kernel: [82948.474019] $ 8 : 000facb3 000facb2 00000002 00064000 May 13 07:24:52 router kernel: [82948.479248] $12 : 00000009 0004001a fffeffff 00001000 May 13 07:24:52 router kernel: [82948.484473] $16 : 8fc02c00 000001b8 01011200 8022b6f0 May 13 07:24:52 router kernel: [82948.489695] $20 : 8ebb0000 8006a664 8e56d81c 01400000 May 13 07:24:52 router kernel: [82948.494913] $24 : 81196320 00000000 May 13 07:24:52 router kernel: [82948.500133] $28 : 8dd62000 8dd63950 8fd77d40 8013694c May 13 07:24:52 router kernel: [82948.505351] Hi : 00000000 May 13 07:24:52 router kernel: [82948.508214] Lo : 00840480 May 13 07:24:52 router kernel: [82948.511113] epc : 80136a70 kmalloc+0x1f8/0x2ec May 13 07:24:52 router kernel: [82948.515887] ra : 8013694c kmalloc+0xd4/0x2ec May 13 07:24:52 router kernel: [82948.520568] Status: 11007c03#011KERNEL EXL IE May 13 07:24:52 router kernel: [82948.524750] Cause : 40800008 (ExcCode 02) May 13 07:24:52 router kernel: [82948.528740] BadVA : 07407800 May 13 07:24:52 router kernel: [82948.531605] PrId : 0001992f (MIPS 1004Kc) May 13 07:24:52 router kernel: [82948.535679] Modules linked in: pppoe ppp_async pppox ppp_generic nf_conntrack_ipv6 mt76x2e mt7603e mt76 mac80211 iptable_nat ipt_REJECT ipt_MASQUERADE cfg80211 cdc_ether xt_time xt_tcpudp xt_tcpmss xt_statistic xt_state xt_recent xt_nat xt_multiport xt_mark xt_mac xt_limit xt_length xt_hl xt_helper xt_ecn xt_dscp xt_conntrack xt_connmark xt_connlimit xt_connbytes xt_comment xt_TCPMSS xt_REDIRECT xt_LOG xt_HL xt_FLOWOFFLOAD xt_DSCP xt_CLASSIFY usbnet slhc nf_reject_ipv4 nf_nat_redirect nf_nat_masquerade_ipv4 nf_conntrack_ipv4 nf_nat_ipv4 nf_nat nf_log_ipv4 nf_flow_table_hw nf_flow_table nf_defrag_ipv6 nf_defrag_ipv4 nf_conntrack_rtcache nf_conntrack libcrc32c iptable_mangle iptable_filter ipt_ECN ip_tables crc_ccitt compat ledtrig_usbport xt_set ip_set_list_set ip_set_hash_netiface ip_set_hash_netport May 13 07:24:52 router kernel: [82948.606444] ip_set_hash_netnet ip_set_hash_net ip_set_hash_netportnet ip_set_hash_mac ip_set_hash_ipportnet ip_set_hash_ipportip ip_set_hash_ipport ip_set_hash_ipmark ip_set_hash_ip ip_set_bitmap_port ip_set_bitmap_ipmac ip_set_bitmap_ip ip_set nfnetlink ip6t_REJECT nf_reject_ipv6 nf_log_ipv6 nf_log_common ip6table_mangle ip6table_filter ip6_tables x_tables vfat fat nls_utf8 nls_iso8859_1 nls_cp437 usb_storage leds_gpio xhci_mtk xhci_plat_hcd xhci_pci xhci_hcd sd_mod scsi_mod gpio_button_hotplug ext4 jbd2 mbcache usbcore nls_base usb_common mii crc32c_generic May 13 07:24:52 router kernel: [82948.655996] Process kworker/u8:1 (pid: 1977, threadinfo=8dd62000, task=8ff3ddc0, tls=00000000) May 13 07:24:52 router kernel: [82948.664578] Stack : 01011200 00400000 8006a664 8f0c719c 00000001 00000000 8fd33300 01011200 May 13 07:24:52 router kernel: [82948.672925] 8fe74850 01011200 00000001 00400000 8006a664 8022b6f0 8fe74850 01011200 May 13 07:24:52 router kernel: [82948.681267] 01411200 8fdf9e00 01011200 01411200 8e56d800 800ecd30 8fe74850 01011200 May 13 07:24:52 router kernel: [82948.689609] 01411200 8fdf9d00 01400000 00400000 8006a664 800ecd30 00060000 00000001 May 13 07:24:52 router kernel: [82948.697952] 8dd63a48 8fe74850 00000000 8fe74850 00000001 8fe74850 00000000 8fe74878 May 13 07:24:52 router kernel: [82948.706292] ... May 13 07:24:52 router kernel: [82948.708733] Call Trace: May 13 07:24:52 router kernel: [82948.711201] [<80136a70>] __kmalloc+0x1f8/0x2ec May 13 07:24:52 router kernel: [82948.715643] [<8022b6f0>] alloc_request_size+0x2c/0x7c May 13 07:24:52 router kernel: [82948.720708] [<800ecd30>] mempool_alloc+0x6c/0×178 May 13 07:24:52 router kernel: [82948.725402] [<8022cf88>] get_request+0×360/0x76c May 13 07:24:52 router kernel: [82948.730005] [<802303c4>] blk_queue_bio+0x1cc/0×430 May 13 07:24:52 router kernel: [82948.734781] [<8022e3cc>] generic_make_request+0xd8/0×288 May 13 07:24:52 router kernel: [82948.740078] [<8022e6a0>] submit_bio+0×124/0×164 May 13 07:24:52 router kernel: [82948.744663] [<8f1c3014>] ext4_io_submit+0×50/0×64 [ext4] May 13 07:24:52 router kernel: [82948.749989] [<8f1a5994>] ext4_mark_inode_dirty+0xeac/0×1368 [ext4] May 13 07:24:52 router kernel: [82948.756166] Code: 32428000 8e020014 00e23821 <8ce20000> 1000002c cc400000 1280ffbc 00000000 8e060010 May 13 07:24:52 router kernel: [82948.765910] May 13 07:24:52 router kernel: [82948.767638] —[ end trace e8f9893fb33e6a26 ]—
and the second case
May 15 15:52:16 router kernel: [67618.480256] CPU 0 Unable to handle kernel paging request at virtual address 07402800, epc == 80136784, ra == 800ecd30 May 15 15:52:16 router kernel: [67618.490997] Oops[#1]: May 15 15:52:16 router kernel: [67618.493275] CPU: 0 PID: 14159 Comm: kworker/u8:1 Not tainted 4.14.37 #0 May 15 15:52:16 router kernel: [67618.499875] Workqueue: writeback wb_workfn (flush-8:0) May 15 15:52:16 router kernel: [67618.504997] task: 8c3276c0 task.stack: 8b656000 May 15 15:52:16 router kernel: [67618.509500] $ 0 : 00000000 00000001 00000000 8121a6c0 May 15 15:52:16 router kernel: [67618.514709] $ 4 : 805aa44c 00000001 00000001 07402800 May 15 15:52:16 router kernel: [67618.519918] $ 8 : 00005ddf 00005dde 8fb9b6a0 00000120 May 15 15:52:16 router kernel: [67618.525127] $12 : 8000001f 00000010 00000124 00000001 May 15 15:52:16 router kernel: [67618.530336] $16 : 8fd4a200 01011200 800ecd30 8b0e0000 May 15 15:52:16 router kernel: [67618.535545] $20 : 00400000 8006a664 8fd4981c 80660000 May 15 15:52:16 router kernel: [67618.540754] $24 : ffffffe0 ffff0000 May 15 15:52:16 router kernel: [67618.545963] $28 : 8b656000 8b657970 8f1c2c24 800ecd30 May 15 15:52:16 router kernel: [67618.551174] Hi : 00000000 May 15 15:52:16 router kernel: [67618.554035] Lo : 008402f0 May 15 15:52:16 router kernel: [67618.556924] epc : 80136784 kmem_cache_alloc+0x13c/0×230 May 15 15:52:16 router kernel: [67618.562323] ra : 800ecd30 mempool_alloc+0x6c/0×178 May 15 15:52:16 router kernel: [67618.567345] Status: 11008403#011KERNEL EXL IE May 15 15:52:16 router kernel: [67618.571515] Cause : 40800008 (ExcCode 02) May 15 15:52:16 router kernel: [67618.575499] BadVA : 07402800 May 15 15:52:16 router kernel: [67618.578361] PrId : 0001992f (MIPS 1004Kc) May 15 15:52:16 router kernel: [67618.582431] Modules linked in: pppoe ppp_async pppox ppp_generic nf_conntrack_ipv6 mt76x2e mt7603e mt76 mac80211 iptable_nat ipt_REJECT ipt_MASQUERADE cfg80211 cdc_ether xt_time xt_tcpudp xt_tcpmss xt_statistic xt_state xt_recent xt_nat xt_multiport xt_mark xt_mac xt_limit xt_length xt_hl xt_helper xt_ecn xt_dscp xt_conntrack xt_connmark xt_connlimit xt_connbytes xt_comment xt_TCPMSS xt_REDIRECT xt_LOG xt_HL xt_FLOWOFFLOAD xt_DSCP xt_CLASSIFY usbnet slhc nf_reject_ipv4 nf_nat_redirect nf_nat_masquerade_ipv4 nf_conntrack_ipv4 nf_nat_ipv4 nf_nat nf_log_ipv4 nf_flow_table_hw nf_flow_table nf_defrag_ipv6 nf_defrag_ipv4 nf_conntrack_rtcache nf_conntrack libcrc32c iptable_mangle iptable_filter ipt_ECN ip_tables crc_ccitt compat ledtrig_usbport xt_set ip_set_list_set ip_set_hash_netiface ip_set_hash_netport May 15 15:52:16 router kernel: [67618.653177] ip_set_hash_netnet ip_set_hash_net ip_set_hash_netportnet ip_set_hash_mac ip_set_hash_ipportnet ip_set_hash_ipportip ip_set_hash_ipport ip_set_hash_ipmark ip_set_hash_ip ip_set_bitmap_port ip_set_bitmap_ipmac ip_set_bitmap_ip ip_set nfnetlink ip6t_REJECT nf_reject_ipv6 nf_log_ipv6 nf_log_common ip6table_mangle ip6table_filter ip6_tables x_tables vfat fat nls_utf8 nls_iso8859_1 nls_cp437 usb_storage leds_gpio xhci_mtk xhci_plat_hcd xhci_pci xhci_hcd sd_mod scsi_mod gpio_button_hotplug ext4 jbd2 mbcache usbcore nls_base usb_common mii crc32c_generic May 15 15:52:16 router kernel: [67618.702675] Process kworker/u8:1 (pid: 14159, threadinfo=8b656000, task=8c3276c0, tls=00000000) May 15 15:52:16 router kernel: [67618.711326] Stack : 8e648b20 8f147e00 8e648b20 01011200 00000001 8022b710 00000002 01011200 May 15 15:52:16 router kernel: [67618.719658] 01411200 8fd49800 01400000 00400000 8006a664 800ecd30 00000001 01011200 May 15 15:52:16 router kernel: [67618.727990] 01411200 8fd49700 01400000 00400000 8006a664 800ecd30 8e330030 8c499000 May 15 15:52:16 router kernel: [67618.736322] 8fd9f000 8b657a2c 01400000 8fd49800 01400000 01400000 8e47fa00 8d44d8f8 May 15 15:52:16 router kernel: [67618.744655] 80660000 80225974 8fd49600 00000100 01400000 8d48d7c0 8e47fa00 8fd49600 May 15 15:52:16 router kernel: [67618.752989] ... May 15 15:52:16 router kernel: [67618.755425] Call Trace: May 15 15:52:16 router kernel: [67618.757859] [<80136784>] kmem_cache_alloc+0x13c/0×230 May 15 15:52:16 router kernel: [67618.762897] [<800ecd30>] mempool_alloc+0x6c/0×178 May 15 15:52:16 router kernel: [67618.767596] [<80225974>] bvec_alloc+0xdc/0×154 May 15 15:52:16 router kernel: [67618.772020] [<80225b44>] bio_alloc_bioset+0×158/0×250 May 15 15:52:16 router kernel: [67618.777111] [<8f1c3358>] ext4_bio_write_page+0×320/0x5c4 [ext4] May 15 15:52:16 router kernel: [67618.783028] [<8f19e3f4>] ext4_convert_inline_data+0×874/0x21a8 [ext4] May 15 15:52:16 router kernel: [67618.789461] [<8f19e860>] ext4_convert_inline_data+0xce0/0x21a8 [ext4] May 15 15:52:16 router kernel: [67618.795881] Code: 32228000 8e020014 00e23821 <8ce20000> 1000002d cc400000 1260ffbc 00000000 8e060010 May 15 15:52:16 router kernel: [67618.805607] May 15 15:52:16 router kernel: [67618.807332] —[ end trace 3b32ff5399a1bc64 ]—
|
|
11.06.2018 | 1586 | Base system | Bug Report | Very Low | Critical | DAP-1522 A1 factory to snapshot kernel panic and system... | Trunk | Unconfirmed |
Task Description
DAP-1522 A1 stock firmware 1.21 or 1.42 , device page https://openwrt.org/toh/hwdata/d-link/d-link_dap-1522_a1 Flash via GUI or Recovery interface , both the same result/fail. Since this device is not supported on 17.04.1 https://downloads.lede-project.org/releases/17.01.4/targets/ramips/rt288x/ I try the snapshot from https://downloads.openwrt.org/snapshots/targets/ramips/rt288x/openwrt-ramips-rt288x-dlink_dap-1522-a1-squashfs-factory.bin Checksum ok
Here is the boot log
U-Boot 1.1.3 (Aug 28 2009 - 15:47:01) Build 001--ALPHA_v011
Board: RT2880 DRAM: 32 MB
twe0 set to <NULL>
toe0 set to <NULL>
============================================
ASIC -VerB/C (MAC to MAC Mode)
DRAM COMPONENT=256Mbits
DRAM BUS=16BIT
Total memory = 32Mbytes
Date:Aug 28 2009 Time:15:47:01
============================================
Eth0 (10/100-M)
Hit any key to stop autoboot: 0
## Booting image at bc440000 ...
Image Name: 7zip Linux Kernel
Created: 1970-01-01 0:00:00 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: -1 Bytes = 4096 MB
Load Address: 8a000000
Entry Point: 8a000000
Uncompressing Kernel Image with LZMA ...
OK
Starting kernel ...
[ 0.000000] Linux version 4.14.48 (buildbot@slashdirt-02) (gcc version 7.3.0 (OpenWrt GCC 7.3.0
r7172-f60301d)) #0 Sat Jun 9 20:39:17 2018
[ 0.000000] SoC Type: Ralink RT2880 id:2 rev:0
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001906c (MIPS 4KEc)
[ 0.000000] MIPS: machine is D-Link DAP-1522 A1
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 08000000 (usable)
[ 0.000000] Wasting 1048576 bytes for tracking 32768 unused pages
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 16kB, VIPT, 4-way, linesize 16 bytes.
[ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 16 byt es
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000009ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000009ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000009ffffff]
[ 0.000000] random: get_random_bytes called from start_kernel+0x8c/0x47c with crng_init=0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 40640
[ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs 2
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 25248K/163840K available (3518K kernel code, 174K rwdata, 844K rodata, 1216K
init, 214K bss, 138592K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=16, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 256
[ 0.000000] Failed to request intc memory
[ 0.000000] Kernel panic - not syncing: Failed to request resources for ralin k,rt2880-sysc
[ 0.000000] Rebooting in 1 seconds..
[ 0.000000] Reboot failed -- System halted
Regards,
|
|
07.11.2018 | 1938 | Base system | Bug Report | Very Low | Critical | CONFIG_PKG_ASLR_PIE and CONFIG_USE_MKLIBS are incompati... | Trunk | Unconfirmed |
Task Description
I’m building OpenWrt trunk (commit dceee8cc09a54f96dee82a6e95e3e77a6dd7ac13) for Netgear R7800 (though I think, device doesn’t matter here).
It turns out that if both CONFIG_PKG_ASLR_PIE and CONFIG_USE_MKLIBS are turned on, the system renders unusable. In my case, when building with GCC 7, dropbear doesn’t start, and when building with GCC 8, the system doesn’t boot, and the status LED is off.
The culprit is this line: https://git.openwrt.org/?p=openwrt/openwrt.git;a=blob;f=include/rootfs.mk;h=76425c017a8b33340dbcc41cecaf1241352c7dbc;hb=HEAD#l7
# first find all programs and add them to the mklibs list
find $(STAGING_DIR_ROOT) -type f -perm /100 -exec \
file -r -N -F '' {} + | \
awk ' /executable.*dynamically/ { print $$1 }' > $(TMP_DIR)/mklibs-progs
It should generate the list of executables for mklibs, however, with PIE turned on, most of the executables don’t get into that list. In my config, only fw_printenv gets into the mklibs-progs list. And, because some executables are not on the list, the symbols they need may be stripped off the libraries, rendering these executables unusable.
The reason is that the file command detects PIE executables as shared objects, not as executables. Compare:
With ASLR off:
bin/busybox ELF 32-bit LSB executable, ARM, EABI5 version 1 (SYSV), dynamically linked, interpreter /lib/ld-musl-armhf.so.1, with debug_info, not stripped
With ASLR on:
bin/busybox ELF 32-bit LSB shared object, ARM, EABI5 version 1 (SYSV), dynamically linked, interpreter /lib/ld-musl-armhf.so.1, with debug_info, not stripped
This one single executable displays the same, independently of ASLR state:
usr/sbin/fw_printenv ELF 32-bit LSB executable, ARM, EABI5 version 1 (SYSV), dynamically linked, interpreter /lib/ld-musl-armhf.so.1, stripped
If CONFIG_PKG_ASLR_PIE=n, all executables are detected properly and get into the mklibs-progs list.
A more proper way should be found to detect executables, as the current one skips PIE executables completely and makes the system unusable, because some of the PIE executables can’t start due to missing symbols in libraries.
I’ve chosen the critical severity, because the system doesn’t work if I set those two config options to y, and this combination isn’t something unusual, because many people would like both increased security and smaller size of the firmware.
|
|
01.01.2019 | 2040 | Base system | Bug Report | Very Low | Critical | gdb 8.2 fails to compile for Raspberry Pi 3B+ | Trunk | Unconfirmed |
Task Description
- Device problem occurs on Attempting build for Raspberry Pi 3B+ with gdbserver included
- Software versions of OpenWrt/LEDE release, packages, etc. commit d3bf5ff9bc7b55b2a3dab93853b33a0cd2c4ca47 (HEAD → master, origin/master, origin/HEAD) Author: Jonas Gorski jonas.gorski@gmail.com Date: Mon Sep 10 11:42:53 2018 +0200
- Steps to reproduce (I successfully built and ran it without gdbserver.) In menuconfig, selected the correct SoC, added Luci, then followed https://openwrt.org/docs/guide-developer/gdb: “Compiling Tools” - exactly as described. “Add debugging to a package” - option “Global build settings > Compile packages with debugging info” (whether this is activated or not has no effect on the problem)
gdb compilation for the target fails, see error below.
I reverted 2 last commits to the gdb package, to what it was at this commit: commit 525b8f06501233414ad6e56fe1134ae82ab28fc2 Author: Rosen Penev rosenp@gmail.com Date: Wed Jun 6 18:22:26 2018 -0700
using these commands: cd package/devel git checkout 525b8f06501 gdb
and the build succeeded. Looks like the updated gdb
.config is attached.
aarch64-openwrt-linux-musl-g++ -x c++ -Os -pipe -mcpu=cortex-a53 -fno-caller-saves -fno-plt -fhonour-copts -Wno-error=unused-but-set-variable -Wno-error=unused-result -iremap/mnt/1TB/ow/openwrt/build_dir/target-aarch64_cortex-a53_musl/gdb-8.2:gdb-8.2 -Wformat -Werror=format-security -fstack-protector -D_FORTIFY_SOURCE=1 -Wl,-z,now -Wl,-z,relro -I. -I. -I./common -I./config -DLOCALEDIR=”“/usr/share/locale”” -DHAVE_CONFIG_H -I./../include/opcode -I./../opcodes/.. -I./../zlib -I../bfd -I./../bfd -I./../include -I../libdecnumber -I./../libdecnumber -I./gnulib/import -Ibuild-gnulib/import -DTUI=1 -Wall -Wpointer-arith -Wno-unused -Wunused-value -Wunused-function -Wno-switch -Wno-char-subscripts -Wempty-body -Wunused-but-set-parameter -Wunused-but-set-variable -Wno-sign-compare -Wno-narrowing -Wno-error=maybe-uninitialized -Wsuggest-override -Wimplicit-fallthrough=3 -Wduplicated-cond -Wformat-nonliteral -c -o aarch64-linux-nat.o -MT aarch64-linux-nat.o -MMD -MP -MF ./.deps/aarch64-linux-nat.Tpo aarch64-linux-nat.c In file included from nat/aarch64-sve-linux-ptrace.h:23:0, from aarch64-linux-nat.c:35: /mnt/1TB/ow/openwrt/staging_dir/toolchain-aarch64_cortex-a53_gcc-7.4.0_musl/include/asm/sigcontext.h:26:8: error: redefinition of ‘struct sigcontext’ struct sigcontext {
In file included from /mnt/1TB/ow/openwrt/staging_dir/toolchain-aarch64_cortex-a53_gcc-7.4.0_musl/include/signal.h:48:0, from build-gnulib/import/signal.h:52, from linux-nat.h:23, from aarch64-linux-nat.c:26: /mnt/1TB/ow/openwrt/staging_dir/toolchain-aarch64_cortex-a53_gcc-7.4.0_musl/include/bits/signal.h:18:16: note: previous definition of ‘struct sigcontext’ typedef struct sigcontext {
In file included from nat/aarch64-sve-linux-ptrace.h:23:0, from aarch64-linux-nat.c:35: /mnt/1TB/ow/openwrt/staging_dir/toolchain-aarch64_cortex-a53_gcc-7.4.0_musl/include/asm/sigcontext.h:63:8: error: redefinition of ‘struct _aarch64_ctx’ struct _aarch64_ctx {
In file included from /mnt/1TB/ow/openwrt/staging_dir/toolchain-aarch64_cortex-a53_gcc-7.4.0_musl/include/signal.h:48:0, from build-gnulib/import/signal.h:52, from linux-nat.h:23, from aarch64-linux-nat.c:26: /mnt/1TB/ow/openwrt/staging_dir/toolchain-aarch64_cortex-a53_gcc-7.4.0_musl/include/bits/signal.h:29:8: note: previous definition of ‘struct _aarch64_ctx’ struct _aarch64_ctx {
In file included from nat/aarch64-sve-linux-ptrace.h:23:0, from aarch64-linux-nat.c:35: /mnt/1TB/ow/openwrt/staging_dir/toolchain-aarch64_cortex-a53_gcc-7.4.0_musl/include/asm/sigcontext.h:70:8: error: redefinition of ‘struct fpsimd_context’ struct fpsimd_context {
In file included from /mnt/1TB/ow/openwrt/staging_dir/toolchain-aarch64_cortex-a53_gcc-7.4.0_musl/include/signal.h:48:0, from build-gnulib/import/signal.h:52, from linux-nat.h:23, from aarch64-linux-nat.c:26: /mnt/1TB/ow/openwrt/staging_dir/toolchain-aarch64_cortex-a53_gcc-7.4.0_musl/include/bits/signal.h:33:8: note: previous definition of ‘struct fpsimd_context’ struct fpsimd_context {
In file included from nat/aarch64-sve-linux-ptrace.h:23:0, from aarch64-linux-nat.c:35: /mnt/1TB/ow/openwrt/staging_dir/toolchain-aarch64_cortex-a53_gcc-7.4.0_musl/include/asm/sigcontext.h:80:8: error: redefinition of ‘struct esr_context’ struct esr_context {
In file included from /mnt/1TB/ow/openwrt/staging_dir/toolchain-aarch64_cortex-a53_gcc-7.4.0_musl/include/signal.h:48:0, from build-gnulib/import/signal.h:52, from linux-nat.h:23, from aarch64-linux-nat.c:26: /mnt/1TB/ow/openwrt/staging_dir/toolchain-aarch64_cortex-a53_gcc-7.4.0_musl/include/bits/signal.h:39:8: note: previous definition of ‘struct esr_context’ struct esr_context {
In file included from nat/aarch64-sve-linux-ptrace.h:23:0, from aarch64-linux-nat.c:35: /mnt/1TB/ow/openwrt/staging_dir/toolchain-aarch64_cortex-a53_gcc-7.4.0_musl/include/asm/sigcontext.h:113:8: error: redefinition of ‘struct extra_context’ struct extra_context {
In file included from /mnt/1TB/ow/openwrt/staging_dir/toolchain-aarch64_cortex-a53_gcc-7.4.0_musl/include/signal.h:48:0, from build-gnulib/import/signal.h:52, from linux-nat.h:23, from aarch64-linux-nat.c:26: /mnt/1TB/ow/openwrt/staging_dir/toolchain-aarch64_cortex-a53_gcc-7.4.0_musl/include/bits/signal.h:43:8: note: previous definition of ‘struct extra_context’ struct extra_context {
aarch64-linux-nat.c: In function ‘void store_sveregs_to_thread(regcache*)’: aarch64-linux-nat.c:419:59: error: invalid use of incomplete type ‘struct store_sveregs_to_thread(regcache*)::user_sve_header’ iovec.iov_len = 1)→size;
aarch64-linux-nat.c:419:28: note: forward declaration of ‘struct store_sveregs_to_thread(regcache)::user_sve_header’ iovec.iov_len = 2)→size;
Makefile:1622: recipe for target ‘aarch64-linux-nat.o’ failed
|
|
21.01.2019 | 2073 | Base system | Bug Report | Very Low | Critical | Sha1 in firmware-utils/src/sha1.c has TLS or DTLS Vulne... | All | Unconfirmed |
Task Description
Hi, The sha1 file in openwrt/tools/firmware-utils/src/sha1.c is not fixed and is vulnerable to remote code execution or DoS. The CVE (CVE-2018-0487) and fixed in multiple other repos including ubuntu. (https://people.canonical.com/~ubuntu-security/cve/2018/CVE-2018-0487.html)
|
|
23.01.2019 | 2079 | Base system | Bug Report | Very Low | Critical | MT7621 - lost RX stream | All | Unconfirmed |
Task Description
Device: TP-LINK RE350 v1 OpenWRT: 18.06-SNAPSHOOT 22.01.2019 Wireless setup:
config wifi-device 'radio0'
option type 'mac80211'
option channel '1'
option hwmode '11g'
option path 'pci0000:00/0000:00:00.0/0000:01:00.0'
option ldpc '1'
option greenfield '0'
option diversity '1'
option htmode 'HT40'
option country 'PL'
option log_level '8'
option disabled '0'
option legacy_rates '0'
option noscan '1'
config wifi-iface
option device 'radio0'
option mode 'sta'
option ssid 'XXX'
option bssid 'xxx'
option encryption 'psk2'
option key 'xxx'
option disassoc_low_ack '0'
option network 'wan'
option disabled '0'
option wmm '1'
config wifi-iface
option device 'radio0'
option mode 'ap'
option ssid 'XXX'
option encryption 'psk2'
option key 'xxx'
option disassoc_low_ack '0'
option network 'lan'
option disabled '0'
option wds '1'
option wmm '1'
Problem and solution: AP and STA works on Channel 1. STA few seconds after connection to upstream AP losts RX stream.
Station xx:xx:xx:xx:xx:xx (on wlan0)
inactive time: 20570 ms
rx bytes: 222792
rx packets: 1657
tx bytes: 1482
tx packets: 20
tx retries: 133
tx failed: 12
beacon loss: 10
beacon rx: 756
rx drop misc: 2
signal: -68 [-68, -69] dBm
signal avg: -68 [-68, -68] dBm
beacon signal avg: 188 dBm
tx bitrate: 43.3 MBit/s MCS 10 short GI
**rx bitrate: 1.0 MBit/s**
authorized: yes
authenticated: yes
associated: yes
preamble: long
WMM/WME: yes
MFP: no
TDLS peer: no
DTIM period: 2
beacon interval:100
short slot time:yes
connected time: 83 seconds
|
|
02.04.2019 | 2218 | Base system | Bug Report | Very Low | Critical | Linksys EA4500 suffers endless reboots: Radio1 (5GHz) c... | Trunk | Unconfirmed |
Task Description
One of 5 EA3500’s, each at a different site, keeps crashing and restarting. Both 18.06.2 and Snapshot r9614-b614954 are suffering it at this particular site. I could finally keep it booting up after disabling radio1 (5 GHz). Other 4 sites have no trouble with the same system and wireless configuration.
I can pretty much rule out hardware problems. Just boot up Snapshot r9614-b614954 on an EA4500, whose radio1 (5G) worked on another site. It suffers the same infinite crash/restart sequence. At least 3 different devices worked at different locations, but crash only at this one.
From the serial console: A crash at backports-4.19.23-1/net/mac80211/rx.c:4516 ieee80211_rx_napi+0x1fc/0xa54 [mac80211]
[ 22.960919] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 23.010664] br-lan: port 1(eth0.1) entered blocking state
[ 23.016172] br-lan: port 1(eth0.1) entered disabled state
[ 23.021848] device eth0.1 entered promiscuous mode
[ 23.026687] device eth0 entered promiscuous mode
[ 23.110502] br-lan: port 1(eth0.1) entered blocking state
[ 23.115976] br-lan: port 1(eth0.1) entered forwarding state
[ 23.121730] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 23.191580] mv643xx_eth_port mv643xx_eth_port.1 eth1: link up, 1000 Mb/s, full duplex, flow control disabled
[ 23.202650] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 24.009012] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 24.015903] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 24.022546] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 25.052979] 0000:01:00.0: unable to load firmware helper image
[ 25.058872] ieee80211 phy0: Cannot start firmware
[ 25.063675] ieee80211 phy0: Trying to reload the firmware again
[ 25.987785] ieee80211 phy0: 88w8366 v7, 20aa4b891bf2, AP firmware 5.2.8.17
[ 26.047574] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 26.113947] 0000:02:00.0: unable to load firmware helper image
[ 26.119821] ieee80211 phy1: Cannot start firmware
[ 26.124636] ieee80211 phy1: Trying to reload the firmware again
[ 26.511780] ieee80211 phy1: 88w8366 v7, 20aa4b891bf4, AP firmware 5.2.8.17
[ 26.565994] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 26.577344] br-lan: port 2(wlan0) entered blocking state
[ 26.582745] br-lan: port 2(wlan0) entered disabled state
[ 26.588309] device wlan0 entered promiscuous mode
[ 26.614795] br-lan: port 3(wlan1) entered blocking state
[ 26.620186] br-lan: port 3(wlan1) entered disabled state
[ 26.625800] device wlan1 entered promiscuous mode
[ 27.137261] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 27.143826] br-lan: port 2(wlan0) entered blocking state
[ 27.149170] br-lan: port 2(wlan0) entered forwarding state
[ 27.179154] ------------[ cut here ]------------
[ 27.183961] WARNING: CPU: 0 PID: 0 at backports-4.19.23-1/net/mac80211/rx.c:4516 ieee80211_rx_napi+0x1fc/0xa54 [mac80211]
[ 27.194991] Modules linked in: pppoe ppp_async pppox ppp_generic nf_conntrack_ipv6 mwl8k mac80211 iptable_nat ipt_REJECT ipt_MASQUERADE cfg80211 xt_time xt_tcpudp xt_state xt_nat xt_multiport xt_mark xt_mac xt_limit xt_conntrack xt_comment xt_TCPMSS xt_REDIRECT xt_LOG xt_FLOWOFFLOAD xt_CT slhc nf_reject_ipv4 nf_nat_redirect nf_nat_masquerade_ipv4 nf_conntrack_ipv4 nf_nat_ipv4 nf_nat nf_log_ipv4 nf_flow_table_hw nf_flow_table nf_defrag_ipv6 nf_defrag_ipv4 nf_conntrack_rtcache nf_conntrack iptable_mangle iptable_filter ip_tables crc_ccitt compat nf_log_ipv6 nf_log_common ip6table_mangle ip6table_filter ip6_tables ip6t_REJECT x_tables nf_reject_ipv6 tun gpio_button_hotplug
[ 27.254721] CPU: 0 PID: 0 Comm: swapper Not tainted 4.14.105 #0
[ 27.260669] Hardware name: Marvell Kirkwood (Flattened Device Tree)
[ 27.266969] Backtrace:
[ 27.269438] [<c010530c>] (dump_backtrace) from [<c01055f4>] (show_stack+0x18/0x1c)
[ 27.277057] r7:bf1f012c r6:00000000 r5:bf227600 r4:00000000
[ 27.282772] [<c01055dc>] (show_stack) from [<c058b880>] (dump_stack+0x20/0x28)
[ 27.290036] [<c058b860>] (dump_stack) from [<c01196b0>] (__warn+0xdc/0x108)
[ 27.297048] [<c01195d4>] (__warn) from [<c0119794>] (warn_slowpath_null+0x28/0x30)
[ 27.304665] r9:c7104ff0 r8:bf226390 r7:bf226318 r6:c71058a0 r5:c7104bc0 r4:c72be9c0
[ 27.312535] [<c011976c>] (warn_slowpath_null) from [<bf1f012c>] (ieee80211_rx_napi+0x1fc/0xa54 [mac80211])
[ 27.322376] [<bf1eff30>] (ieee80211_rx_napi [mac80211]) from [<bf1cb68c>] (ieee80211_tasklet_handler+0x64/0xc0 [mac80211])
[ 27.333486] r10:00000000 r9:c7104ff0 r8:bf226390 r7:bf226318 r6:c7104bc0 r5:c7104fe4
[ 27.341359] r4:c72be9c0
[ 27.343976] [<bf1cb628>] (ieee80211_tasklet_handler [mac80211]) from [<c011c5dc>] (tasklet_action+0x88/0xd8)
[ 27.353865] r9:00000100 r8:ffffe000 r7:00000000 r6:c082a000 r5:c08085fc r4:00000000
[ 27.361664] [<c011c554>] (tasklet_action) from [<c0101464>] (__do_softirq+0xac/0x25c)
[ 27.369534] r7:c082a020 r6:40000006 r5:c082a038 r4:00000006
[ 27.375236] [<c01013b8>] (__do_softirq) from [<c011c940>] (irq_exit+0xc8/0x110)
[ 27.382594] r10:00000000 r9:c0801f00 r8:c7805200 r7:00000001 r6:00000000 r5:c0829178
[ 27.390458] r4:00000000
[ 27.393022] [<c011c878>] (irq_exit) from [<c01465e4>] (__handle_domain_irq+0x8c/0xa8)
[ 27.400893] [<c0146558>] (__handle_domain_irq) from [<c010138c>] (orion_handle_irq+0x74/0xa0)
[ 27.409469] r9:c0801f00 r8:00000001 r7:c085564c r6:c780801c r5:00000400 r4:0000000a
[ 27.417263] [<c0101318>] (orion_handle_irq) from [<c01060c8>] (__irq_svc+0x68/0x84)
[ 27.424968] Exception stack(0xc0801f00 to 0xc0801f48)
[ 27.430044] 1f00: 00000000 00000000 00000000 60000013 00000000 ffffe000 c0803094 c08206e0
[ 27.438271] 1f20: c080a852 c065e3e0 00000000 c0801f5c c0801f50 c0801f50 c0102ec0 c05a6814
[ 27.446494] 1f40: 60000013 ffffffff
[ 27.450004] r10:00000000 r9:c0800000 r8:c080a852 r7:c0801f34 r6:ffffffff r5:60000013
[ 27.457875] r4:c05a6814
[ 27.460441] [<c05a67dc>] (default_idle_call) from [<c013fdb8>] (do_idle+0x84/0x144)
[ 27.468154] [<c013fd34>] (do_idle) from [<c01400d8>] (cpu_startup_entry+0x14/0x18)
[ 27.475774] r10:00721c14 r9:c0723a20 r8:c7ffcc80 r7:00000000 r6:c0803020 r5:ffffffff
[ 27.483654] r4:c0809c4c r3:40000013
[ 27.487258] [<c01400c4>] (cpu_startup_entry) from [<c05a1660>] (rest_init+0x74/0x94)
[ 27.495063] [<c05a15ec>] (rest_init) from [<c0700d3c>] (start_kernel+0x3a0/0x424)
[ 27.502595] r5:ffffffff r4:c08299a0
[ 27.506188] [<c070099c>] (start_kernel) from [<00008048>] (0x8048)
[ 27.512404] ---[ end trace 351d5fe97981d9fa ]---
|
|
06.07.2019 | 2359 | Base system | Bug Report | Very Low | Critical | Able to use channels out of regulatory domain(ES) in 5... | Trunk | Unconfirmed |
Task Description
Device: TP-Link Archer C7 v5 (ath79) Software versions of OpenWrt: latest snapshot https://downloads.openwrt.org/snapshots/targets/ath79/generic/openwrt-ath79-generic-tplink_archer-c7-v5-squashfs-sysupgrade.bin
Anything upper 5700 MHz [140] should be disabled.
iw list:
[...]
Frequencies:
* 5180 MHz [36] (23.0 dBm)
* 5200 MHz [40] (23.0 dBm)
* 5220 MHz [44] (23.0 dBm)
* 5240 MHz [48] (23.0 dBm)
* 5260 MHz [52] (20.0 dBm) (radar detection)
* 5280 MHz [56] (20.0 dBm) (radar detection)
* 5300 MHz [60] (20.0 dBm) (radar detection)
* 5320 MHz [64] (20.0 dBm) (radar detection)
* 5500 MHz [100] (26.0 dBm) (radar detection)
* 5520 MHz [104] (26.0 dBm) (radar detection)
* 5540 MHz [108] (26.0 dBm) (radar detection)
* 5560 MHz [112] (26.0 dBm) (radar detection)
* 5580 MHz [116] (26.0 dBm) (radar detection)
* 5600 MHz [120] (26.0 dBm) (radar detection)
* 5620 MHz [124] (26.0 dBm) (radar detection)
* 5640 MHz [128] (26.0 dBm) (radar detection)
* 5660 MHz [132] (26.0 dBm) (radar detection)
* 5680 MHz [136] (26.0 dBm) (radar detection)
* 5700 MHz [140] (26.0 dBm) (radar detection)
* 5720 MHz [144] (disabled)
* 5745 MHz [149] (13.0 dBm)
* 5765 MHz [153] (13.0 dBm)
* 5785 MHz [157] (13.0 dBm)
* 5805 MHz [161] (13.0 dBm)
* 5825 MHz [165] (13.0 dBm)
* 5845 MHz [169] (13.0 dBm)
* 5865 MHz [173] (13.0 dBm)
[...]
|
|
14.11.2019 | 2594 | Base system | Bug Report | Very Low | Critical | Kernel panic when configuring network on mvebu ( Turris... | Trunk | Unconfirmed |
Task Description
- Latest snapshot from today - Does not happen on 18.0.6.x - Router enters reboot loop
Several ways to trigger bug but it essentially revolves around bringing up a VLAN interface inside a bridge.
Some configuration examples that triggers the bug:
config interface 'lan'
option type 'bridge'
option proto 'static'
option netmask '255.255.255.0'
option ip6assign '60'
option delegate '0'
option igmp_snooping '1'
option ifname 'lan0 lan1 lan2 lan3 lan4.12'
option ipaddr '192.168.88.254'
another one:
config interface 'iptv'
option proto 'none'
option type 'bridge'
option ifname 'eth2.12 lan4.12'
The output is:
[ 16.828573] device lan3 entered promiscuous mode
[ 16.876458] mv88e6085 f1072004.mdio-mii:10 lan4: configuring for phy/gmii link mode
[ 16.884237] IPv6: ADDRCONF(NETDEV_UP): lan4: link is not ready
[ 16.891531] br-lan: port 5(lan4.12) entered blocking state
[ 16.897098] br-lan: port 5(lan4.12) entered disabled state
[ 16.904047] device lan4.12 entered promiscuous mode
[ 16.908940] device lan4 entered promiscuous mode
[ 16.918101] Unable to handle kernel NULL pointer dereference at virtual address 00000518
[ 16.926236] pgd = 6295ce7a
[ 16.928948] [00000518] *pgd=2da78831, *pte=00000000, *ppte=00000000
[ 16.935252] Internal error: Oops: 17 [#1] SMP ARM
[ 16.939965] Modules linked in: ath9k ath9k_common pppoe ppp_async ath9k_hw ath10k_pci ath10k_core ath pptp pppox ppp_mppe ppp_generic nf_flow_table_ipv6 nf_flow_table_ipv4 nf_flow_tabs
[ 17.011450] nf_reject_ipv4 nf_nat_rtsp nf_nat_ipv4 nf_nat_ftp nf_nat nf_log_ipv4 nf_flow_table_hw nf_flow_table nf_conntrack_rtsp nf_conntrack_rtcache nf_conntrack_netlink nf_conntrat
[ 17.082567] nfnetlink nf_log_ipv6 nf_log_common ip6table_mangle ip6table_filter ip6_tables ip6t_REJECT x_tables nf_reject_ipv6 ip_gre gre ifb ip6_udp_tunnel udp_tunnel ip_tunnel autoc
[ 17.140899] CPU: 1 PID: 1968 Comm: netifd Not tainted 4.19.82 #0
[ 17.146917] Hardware name: Marvell Armada 380/385 (Device Tree)
[ 17.152856] PC is at br_vlan_enabled+0x0/0x10
[ 17.157224] LR is at dsa_port_vlan_add+0x40/0x88
[ 17.161851] pc : [<c06678c0>] lr : [<c066d100>] psr: 60000013
[ 17.168130] sp : ed5abca0 ip : 00000001 fp : ed5abdb6
[ 17.173364] r10: 00000001 r9 : edb93500 r8 : ec1e6800
[ 17.178599] r7 : ed5abd04 r6 : ed5abd24 r5 : ee864000 r4 : ee94424c
[ 17.185140] r3 : 00000004 r2 : ed5abd04 r1 : 00000000 r0 : 00000000
[ 17.191682] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
[ 17.198832] Control: 10c5387d Table: 2d5c004a DAC: 00000051
[ 17.204590] Process netifd (pid: 1968, stack limit = 0xab1173e4)
[ 17.210609] Stack: (0xed5abca0 to 0xed5ac000)
[ 17.214976] bca0: ed5abd24 ed5abd04 00000000 00000004 ffffffa1 c0674dbc ffff916c c068efc0
[ 17.223173] bcc0: 00000000 ffffffa1 ec1e6800 ed5abd24 ed5abd04 c0674de4 ee937ea0 ec1e6868
[ 17.231370] bce0: 00000001 ec7b7840 ec1e6800 ed5abd24 eda5e000 c0674e94 ef3cda40 ffffffff
[ 17.239566] bd00: ef08c000 ed5abd04 ed5abd04 c0945001 ec7b7840 ec7b7840 ef1783c0 c066b5bc
[ 17.247763] bd20: c0a03db0 ec1e6800 00000001 00000000 00000000 00000000 00010006 00000001
[ 17.255959] bd40: 00000000 c0668f64 eeb9c544 00000006 00000001 00000000 eda5e080 00000036
[ 17.264156] bd60: ed5abd84 c0148948 ef0f304c ef0f3040 ef0f304c 00000000 00000000 ef1783c0
[ 17.272354] bd80: ec7b7840 eda5e000 00000001 00000000 00000006 c066780c ed5abdb6 c0669df0
[ 17.280551] bda0: ffffffa1 ee864000 ed5abe23 ed5abe04 00000000 000148ac ef1783c0 ed5abdb6
[ 17.288747] bdc0: 00020003 00000008 00001000 01010000 00000000 00000000 c066780c 00020003
[ 17.296943] bde0: 00000008 00001000 01010000 00000000 00000000 c066780c ef178418 00000000
[ 17.305140] be00: ef1783c0 eda5e000 00000000 00000000 eda5e080 00000036 0003d7a8 c0669f20
[ 17.313337] be20: 00ffffe5 edb93000 00000007 00000002 00000000 00000000 00000000 00000000
[ 17.321533] be40: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 c0a03c48
[ 17.329730] be60: ec1e6800 ec1e6800 00000000 eda5e000 edb93500 c06595ac 00000000 c012e864
[ 17.337928] be80: edb93500 000089a2 edb93000 ed5abef4 c0739a90 ed5abeec 00000000 c05932c0
[ 17.346125] bea0: 00e0f13b c0a2b940 ed5abef4 c056bbdc ed5abef4 000000a2 000089a2 c0a2b940
[ 17.354323] bec0: ed5abeec c059395c 000089a2 00000051 bed4aba8 c0a2b940 ef0dc300 ed5aa000
[ 17.362519] bee0: 00000036 c05506c4 00000000 eed51d01 eea7c410 6c2d7262 00006e61 00000000
[ 17.370715] bf00: 00000000 00000013 00000000 00000000 00000000 c0a03c48 bed4aba8 eedff1a0
[ 17.378911] bf20: 000089a2 bed4aba8 ef0dc300 c0225788 00000000 eecf97f8 eecf9848 c07ea5a8
[ 17.387108] bf40: ed5409c0 00000000 eed51d60 eea7c410 eecf97f8 40000010 ed5409c8 c0214558
[ 17.395304] bf60: 00000020 00000000 00000000 ef3cde74 ef0dc300 00000008 000089a2 bed4aba8
[ 17.403501] bf80: ef0dc300 ed5aa000 00000036 c022585c 00e20c40 000089a2 b6edb6d8 00000036
[ 17.411699] bfa0: c0101204 c0101000 00e20c40 000089a2 00000008 000089a2 bed4aba8 bed4aba0
[ 17.419896] bfc0: 00e20c40 000089a2 b6edb6d8 00000036 00e20c78 b6edb6d8 00e20de4 0003d7a8
[ 17.428094] bfe0: 0003cd54 bed4ab88 000137c4 b6f5439c 80000010 00000008 00000000 00000000
[ 17.436295] [<c06678c0>] (br_vlan_enabled) from [<c066d100>] (dsa_port_vlan_add+0x40/0x88)
[ 17.444584] [<c066d100>] (dsa_port_vlan_add) from [<c0674dbc>] (__switchdev_port_obj_add+0x30/0x8c)
[ 17.453652] [<c0674dbc>] (__switchdev_port_obj_add) from [<c0674de4>] (__switchdev_port_obj_add+0x58/0x8c)
[ 17.463329] [<c0674de4>] (__switchdev_port_obj_add) from [<c0674e94>] (switchdev_port_obj_add_now+0x7c/0xf0)
[ 17.473181] [<c0674e94>] (switchdev_port_obj_add_now) from [<c066b5bc>] (br_switchdev_port_vlan_add+0x3c/0x44)
[ 17.483207] [<c066b5bc>] (br_switchdev_port_vlan_add) from [<c0668f64>] (__vlan_add+0x50/0x5b4)
[ 17.491926] [<c0668f64>] (__vlan_add) from [<c0669df0>] (nbp_vlan_add+0x210/0x244)
[ 17.499514] [<c0669df0>] (nbp_vlan_add) from [<c0669f20>] (nbp_vlan_init+0xfc/0x158)
[ 17.507278] [<c0669f20>] (nbp_vlan_init) from [<c06595ac>] (br_add_if+0x3c8/0x5ac)
[ 17.514868] [<c06595ac>] (br_add_if) from [<c05932c0>] (dev_ifsioc+0x36c/0x390)
[ 17.522194] [<c05932c0>] (dev_ifsioc) from [<c059395c>] (dev_ioctl+0x5cc/0x63c)
[ 17.529522] [<c059395c>] (dev_ioctl) from [<c05506c4>] (sock_ioctl+0x52c/0x5a8)
[ 17.536849] [<c05506c4>] (sock_ioctl) from [<c0225788>] (do_vfs_ioctl+0x828/0x8c8)
[ 17.544438] [<c0225788>] (do_vfs_ioctl) from [<c022585c>] (ksys_ioctl+0x34/0x58)
[ 17.551851] [<c022585c>] (ksys_ioctl) from [<c0101000>] (ret_fast_syscall+0x0/0x54)
[ 17.559523] Exception stack(0xed5abfa8 to 0xed5abff0)
[ 17.564587] bfa0: 00e20c40 000089a2 00000008 000089a2 bed4aba8 bed4aba0
[ 17.572784] bfc0: 00e20c40 000089a2 b6edb6d8 00000036 00e20c78 b6edb6d8 00e20de4 0003d7a8
[ 17.580980] bfe0: 0003cd54 bed4ab88 000137c4 b6f5439c
[ 17.586044] Code: 18bd8010 e05c0002 13a00001 e8bd8010 (e5d00518)
[ 17.592168] ---[ end trace d312a86e3174f2be ]---
[ 17.596800] Kernel panic - not syncing: Fatal exception
[ 17.602039] CPU0: stopping
[ 17.604755] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G D 4.19.82 #0
[ 17.612167] Hardware name: Marvell Armada 380/385 (Device Tree)
[ 17.618108] [<c010ea7c>] (unwind_backtrace) from [<c010a9bc>] (show_stack+0x10/0x14)
[ 17.625871] [<c010a9bc>] (show_stack) from [<c0678cd8>] (dump_stack+0x84/0x98)
[ 17.633111] [<c0678cd8>] (dump_stack) from [<c010d61c>] (handle_IPI+0xf0/0x19c)
[ 17.640442] [<c010d61c>] (handle_IPI) from [<c03ba714>] (gic_handle_irq+0x74/0x78)
[ 17.648032] [<c03ba714>] (gic_handle_irq) from [<c0101a0c>] (__irq_svc+0x6c/0x90)
[ 17.655529] Exception stack(0xc0a01f30 to 0xc0a01f78)
[ 17.660591] 1f20: 00000000 0004498c ef6d7304 c0114480
[ 17.668788] 1f40: c0a00000 c0a03c6c 00000000 c0a03cac c0944500 00000000 00000000 c0a01f88
[ 17.676984] 1f60: c0a0ecc0 c0a01f80 c01082f8 c01082fc 60000013 ffffffff
[ 17.683617] [<c0101a0c>] (__irq_svc) from [<c01082fc>] (arch_cpu_idle+0x34/0x38)
[ 17.691036] [<c01082fc>] (arch_cpu_idle) from [<c014c598>] (do_idle+0xd8/0x1b4)
[ 17.698363] [<c014c598>] (do_idle) from [<c014c8d0>] (cpu_startup_entry+0x18/0x1c)
[ 17.705952] [<c014c8d0>] (cpu_startup_entry) from [<c0900df8>] (start_kernel+0x4f4/0x504)
[ 17.714149] Rebooting in 3 seconds..
finally I found a configuration that does not put the router in an endless reboot loop but that nevertheless crashes the kernel in the same way when issuing the reboot command:
config interface 'iptv'
option proto 'none'
option type 'bridge'
option ifname 'eth2 eth2.12 lan4 lan4.12'
The above configuration will not crash the kernel on boot, and the iptv interface will be up. but when issuing the reboot command this happens:
root@gateway:/# reboot
root@gateway:/# [ 818.621237] br-iptv: port 1(eth2) entered disabled state
[ 818.652955] device eth2.12 left promiscuous mode
[ 818.657586] device eth2 left promiscuous mode
[ 818.662007] br-iptv: port 2(eth2.12) entered disabled state
[ 818.704719] br-iptv: port 3(lan4) entered disabled state
[ 818.744413] device lan4.12 left promiscuous mode
[ 818.749044] device lan4 left promiscuous mode
[ 818.753517] br-iptv: port 4(lan4.12) entered disabled state
[ 818.759119] Unable to handle kernel NULL pointer dereference at virtual address 00000518
[ 818.767236] pgd = 5685c1a5
[ 818.769947] [00000518] *pgd=2d74d831, *pte=00000000, *ppte=00000000
[ 818.776239] Internal error: Oops: 17 [#1] SMP ARM
[ 818.780951] Modules linked in: cifsd ath9k ath9k_common pppoe ppp_async ath9k_hw ath10k_pci ath10k_core ath pptp pppox ppp_mppe ppp_generic nf_flow_table_ipv6 nf_flow_table_ipv4 nf_fl4
[ 818.852080] nf_tables nf_reject_ipv4 nf_nat_rtsp nf_nat_ipv4 nf_nat_ftp nf_nat nf_log_ipv4 nf_flow_table_hw nf_flow_table nf_conntrack_rtsp nf_conntrack_rtcache nf_conntrack_netlink t
[ 818.922931] nfnetlink nf_log_ipv6 nf_log_common ip6table_mangle ip6table_filter ip6_tables ip6t_REJECT x_tables nf_reject_ipv6 ip_gre gre ifb ip6_udp_tunnel udp_tunnel ip_tunnel auto]
[ 818.983872] CPU: 0 PID: 1975 Comm: netifd Not tainted 4.19.82 #0
[ 818.989890] Hardware name: Marvell Armada 380/385 (Device Tree)
[ 818.995829] PC is at br_vlan_enabled+0x0/0x10
[ 819.000195] LR is at dsa_port_vlan_del+0x48/0x90
[ 819.004821] pc : [<c066a284>] lr : [<c066fb48>] psr: 60000013
[ 819.011101] sp : ed627d60 ip : c0a2d60c fp : 00000018
[ 819.016337] r10: 00000036 r9 : ed4f5380 r8 : eda63500
[ 819.021572] r7 : edbb4800 r6 : ed627dac r5 : ef369800 r4 : eeba764c
[ 819.028113] r3 : 00000004 r2 : 00000000 r1 : ed627dac r0 : 00000000
[ 819.034654] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
[ 819.041804] Control: 10c5387d Table: 2d7b804a DAC: 00000051
[ 819.047561] Process netifd (pid: 1975, stack limit = 0x1b8c3f18)
[ 819.053580] Stack: (0xed627d60 to 0xed628000)
[ 819.057947] 7d60: ed627dac 00000000 00000000 00000004 ffffffa1 c0678988 00000000 ed627d84
[ 819.066144] 7d80: ffffffa1 edbb4800 ed627dac c06789b0 ed627d90 edbb4868 00000001 eda9b880
[ 819.074341] 7da0: ed0933c0 c066dfb8 00000000 edbb4800 00000001 00000000 00000000 00000000
[ 819.082538] 7dc0: 00010000 00000001 00000000 c066ab54 00000000 edb64c00 00000000 00000001
[ 819.090735] 7de0: 00000000 c0a2b980 c0a67a78 00000001 eb3dc000 00000001 edb64c00 edbb4800
[ 819.098931] 7e00: 00480020 c0a2b980 edb64c00 00000000 00000018 c05b0ce4 00480020 00000000
[ 819.107128] 7e20: 00000000 edbb4800 00480020 ed093448 ed093470 eda63500 eda63500 edbb4800
[ 819.115325] 7e40: 00000000 c066adf0 ed747800 ed0933c0 eda63500 c066d12c ed627ef4 eda63500
[ 819.123522] 7e60: edbb4800 ed747800 eda63500 c065bbc4 eda63500 eda63000 ed627ef4 c0739c28
[ 819.131719] 7e80: ed627eec 00000000 00000036 c065c53c 000089a3 eda63000 ed627ef4 c05947cc
[ 819.139916] 7ea0: 00000000 ed627ef4 000000a3 000089a3 ed627ef4 000000a3 000089a3 c0a2b980
[ 819.148113] 7ec0: ed627eec c0594e68 000089a3 00000051 be956c30 c0a2b980 ed411180 ed626000
[ 819.156309] 7ee0: 00000036 c0551c24 ef6d9040 ee91a501 ee91a540 692d7262 00767470 00000000
[ 819.164506] 7f00: 00000000 00000013 00000000 00000000 00000000 c0a03c48 be956c30 eece5360
[ 819.172703] 7f20: 000089a3 be956c30 ed411180 c0225788 eb3e8018 ef6d9000 ee954540 00000000
[ 819.180900] 7f40: ee91a4c0 ee993180 c0701b6c ffffe000 ed627f8c c068f5f8 ed627f74 2ed94000
[ 819.189097] 7f60: c0944b90 a0000193 c0944b90 ed626000 ed411180 00000008 000089a3 be956c30
[ 819.197294] 7f80: ed411180 ed626000 00000036 c022585c 00660860 000089a3 b6eb8ca8 00000036
[ 819.205490] 7fa0: c0101204 c0101000 00660860 000089a3 00000008 000089a3 be956c30 be956c28
[ 819.213687] 7fc0: 00660860 000089a3 b6eb8ca8 00000036 be956cf4 00000018 0063f040 00000018
[ 819.221884] 7fe0: 0003cd54 be956c10 000137c4 b6f0339c 60000010 00000008 00000000 00000000
[ 819.230085] [<c066a284>] (br_vlan_enabled) from [<c066fb48>] (dsa_port_vlan_del+0x48/0x90)
[ 819.238375] [<c066fb48>] (dsa_port_vlan_del) from [<c0678988>] (switchdev_port_obj_del_now+0x2c/0x84)
[ 819.247618] [<c0678988>] (switchdev_port_obj_del_now) from [<c06789b0>] (switchdev_port_obj_del_now+0x54/0x84)
[ 819.257643] [<c06789b0>] (switchdev_port_obj_del_now) from [<c066dfb8>] (br_switchdev_port_vlan_del+0x3c/0x44)
[ 819.267670] [<c066dfb8>] (br_switchdev_port_vlan_del) from [<c066ab54>] (__vlan_del+0x90/0x304)
[ 819.276390] [<c066ab54>] (__vlan_del) from [<c066adf0>] (__vlan_flush+0x28/0x44)
[ 819.283804] [<c066adf0>] (__vlan_flush) from [<c066d12c>] (nbp_vlan_flush+0x60/0x7c)
[ 819.291568] [<c066d12c>] (nbp_vlan_flush) from [<c065bbc4>] (del_nbp+0x154/0x260)
[ 819.299069] [<c065bbc4>] (del_nbp) from [<c065c53c>] (br_del_if+0x30/0xdc)
[ 819.305963] [<c065c53c>] (br_del_if) from [<c05947cc>] (dev_ifsioc+0x36c/0x390)
[ 819.313290] [<c05947cc>] (dev_ifsioc) from [<c0594e68>] (dev_ioctl+0x5cc/0x63c)
[ 819.320618] [<c0594e68>] (dev_ioctl) from [<c0551c24>] (sock_ioctl+0x52c/0x5a8)
[ 819.327945] [<c0551c24>] (sock_ioctl) from [<c0225788>] (do_vfs_ioctl+0x828/0x8c8)
[ 819.335533] [<c0225788>] (do_vfs_ioctl) from [<c022585c>] (ksys_ioctl+0x34/0x58)
[ 819.342946] [<c022585c>] (ksys_ioctl) from [<c0101000>] (ret_fast_syscall+0x0/0x54)
[ 819.350618] Exception stack(0xed627fa8 to 0xed627ff0)
[ 819.355681] 7fa0: 00660860 000089a3 00000008 000089a3 be956c30 be956c28
[ 819.363878] 7fc0: 00660860 000089a3 b6eb8ca8 00000036 be956cf4 00000018 0063f040 00000018
[ 819.372074] 7fe0: 0003cd54 be956c10 000137c4 b6f0339c
[ 819.377138] Code: 18bd8010 e05c0002 13a00001 e8bd8010 (e5d00518)
[ 819.383264] ---[ end trace 6cfc8f01d47fa91b ]---
[ 819.387891] Kernel panic - not syncing: Fatal exception
[ 819.393130] CPU1: stopping
[ 819.395844] CPU: 1 PID: 0 Comm: swapper/1 Tainted: G D 4.19.82 #0
[ 819.403256] Hardware name: Marvell Armada 380/385 (Device Tree)
[ 819.409195] [<c010ea7c>] (unwind_backtrace) from [<c010a9bc>] (show_stack+0x10/0x14)
[ 819.416959] [<c010a9bc>] (show_stack) from [<c067c6d8>] (dump_stack+0x84/0x98)
[ 819.424199] [<c067c6d8>] (dump_stack) from [<c010d61c>] (handle_IPI+0xf0/0x19c)
[ 819.431530] [<c010d61c>] (handle_IPI) from [<c03ba714>] (gic_handle_irq+0x74/0x78)
[ 819.439119] [<c03ba714>] (gic_handle_irq) from [<c0101a0c>] (__irq_svc+0x6c/0x90)
[ 819.446618] Exception stack(0xef091f60 to 0xef091fa8)
[ 819.451682] 1f60: 00000000 008028b0 ef6e2304 c0114480 ef090000 c0a03c6c 00000001 c0a03cac
[ 819.459879] 1f80: c0944500 00000000 00000000 ef091fb8 c0a0ed00 ef091fb0 c01082f8 c01082fc
[ 819.468074] 1fa0: 60000013 ffffffff
[ 819.471573] [<c0101a0c>] (__irq_svc) from [<c01082fc>] (arch_cpu_idle+0x34/0x38)
[ 819.478991] [<c01082fc>] (arch_cpu_idle) from [<c014c598>] (do_idle+0xd8/0x1b4)
[ 819.486319] [<c014c598>] (do_idle) from [<c014c8d0>] (cpu_startup_entry+0x18/0x1c)
[ 819.493907] [<c014c8d0>] (cpu_startup_entry) from [<001023ac>] (0x1023ac)
[ 819.500711] Rebooting in 3 seconds..
finally I have tried with another port ( lan3 ) and it is the same thing.
for instance:
config interface 'iptv'
option proto 'none'
option type 'bridge'
option ifname 'eth2.12 lan3.12'
results in the following panic on boot:
[ 16.893737] mv88e6085 f1072004.mdio-mii:10 lan3: configuring for phy/gmii link mode
[ 16.901473] IPv6: ADDRCONF(NETDEV_UP): lan3: link is not ready
[ 16.908715] br-iptv: port 2(lan3.12) entered blocking state
[ 16.914350] br-iptv: port 2(lan3.12) entered disabled state
[ 16.920120] device lan3.12 entered promiscuous mode
[ 16.925097] device lan3 entered promiscuous mode
[ 16.929731] device eth1 entered promiscuous mode
[ 16.936690] Unable to handle kernel NULL pointer dereference at virtual address 00000518
[ 16.944816] pgd = c664e7e5
[ 16.947529] [00000518] *pgd=2d1bf831, *pte=00000000, *ppte=00000000
[ 16.953830] Internal error: Oops: 17 [#1] SMP ARM
[ 16.958543] Modules linked in: ath9k ath9k_common pppoe ppp_async ath9k_hw ath10k_pci ath10k_core ath pptp pppox ppp_mppe ppp_generic nf_flow_table_ipv6 nf_flow_table_ipv4 nf_flow_tabs
[ 17.030024] nf_reject_ipv4 nf_nat_rtsp nf_nat_ipv4 nf_nat_ftp nf_nat nf_log_ipv4 nf_flow_table_hw nf_flow_table nf_conntrack_rtsp nf_conntrack_rtcache nf_conntrack_netlink nf_conntrak
[ 17.100876] nf_log_ipv6 nf_log_common ip6table_mangle ip6table_filter ip6_tables ip6t_REJECT x_tables nf_reject_ipv6 ip_gre gre ifb ip6_udp_tunnel udp_tunnel ip_tunnel autofs4 nls_utc
[ 17.158945] CPU: 1 PID: 1975 Comm: netifd Not tainted 4.19.82 #0
[ 17.164964] Hardware name: Marvell Armada 380/385 (Device Tree)
[ 17.170904] PC is at br_vlan_enabled+0x0/0x10
[ 17.175270] LR is at dsa_port_vlan_add+0x40/0x88
[ 17.179897] pc : [<c066a284>] lr : [<c066fab8>] psr: 60000013
[ 17.186177] sp : ed615ca0 ip : 00000001 fp : ed615db6
[ 17.191411] r10: 00000001 r9 : edbce500 r8 : ec1a2000
[ 17.196646] r7 : ed615d04 r6 : ed615d24 r5 : ef3da000 r4 : ef32b1dc
[ 17.203186] r3 : 00000003 r2 : ed615d04 r1 : 00000000 r0 : 00000000
[ 17.209728] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
[ 17.216879] Control: 10c5387d Table: 2d61004a DAC: 00000051
[ 17.222636] Process netifd (pid: 1975, stack limit = 0xc606eb54)
[ 17.228656] Stack: (0xed615ca0 to 0xed616000)
[ 17.233023] 5ca0: ed615d24 ed615d04 00000000 00000003 ffffffa1 c06787b8 ef05aa80 ee921580
[ 17.241220] 5cc0: 00000000 ffffffa1 ec1a2000 ed615d24 ed615d04 c06787e0 c0945000 ec1a2068
[ 17.249418] 5ce0: c0a03db0 eb19db40 ec1a2000 ed615d24 ed4b1000 c0678890 ef05aa00 c013dd3c
[ 17.257615] 5d00: ef05aa00 ed615d04 ed615d04 c0945001 eb19db40 eb19db40 ed027d80 c066df74
[ 17.265812] 5d20: ed615d64 ec1a2000 00000001 00000000 00000000 00000000 00010006 00000001
[ 17.274009] 5d40: 00000000 c066b924 ef05aa04 00000006 00000001 00000000 ed4b1080 00000036
[ 17.282205] 5d60: ed615d84 c0148948 ef18404c ef184040 ef18404c 00000000 00000000 ed027d80
[ 17.290402] 5d80: eb19db40 ed4b1000 00000001 00000000 00000006 c066a1d0 ed615db6 c066c7a8
[ 17.298598] 5da0: ffffffa1 ef3da000 ed615e23 ed615e04 00000000 000182a8 ed027d80 ed615db6
[ 17.306796] 5dc0: 00020003 00000008 00001000 01010000 00000000 00000000 c066a1d0 00020003
[ 17.314992] 5de0: 00000008 00001000 01010000 00000000 00000000 c066a1d0 ed027dd8 00000000
[ 17.323190] 5e00: ed027d80 ed4b1000 00000000 00000000 ed4b1080 00000036 0003d7a8 c066c8d8
[ 17.331387] 5e20: 00974080 edbce000 00000007 00000002 00000000 00000000 00000000 00000000
[ 17.339583] 5e40: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 c0a03c48
[ 17.347779] 5e60: ec1a2000 ec1a2000 00000000 ed4b1000 edbce500 c065c328 00000000 c012e864
[ 17.355976] 5e80: edbce500 000089a2 edbce000 ed615ef4 c0739c28 ed615eec 00000000 c05947cc
[ 17.364172] 5ea0: 01cc615b c0a2b980 ed615ef4 c056d0e8 ed615ef4 000000a2 000089a2 c0a2b980
[ 17.372370] 5ec0: ed615eec c0594e68 000089a2 00000051 bedadba8 c0a2b980 ef0ce840 ed614000
[ 17.380566] 5ee0: 00000036 c0551c24 00000000 eed52001 eea71410 692d7262 00767470 00000000
[ 17.388763] 5f00: 00000000 00000013 00000000 00000000 00000000 c0a03c48 bedadba8 eee3f360
[ 17.396960] 5f20: 000089a2 bedadba8 ef0ce840 c0225788 00000000 eecfe880 eecfe8d0 c07eafec
[ 17.405156] 5f40: ed631840 00000000 eed52000 eea71410 eecfe880 40000010 ed631848 c0214558
[ 17.413352] 5f60: 00000020 00000000 00000000 ee921934 ef0ce840 00000008 000089a2 bedadba8
[ 17.421548] 5f80: ef0ce840 ed614000 00000036 c022585c 01cd75c0 000089a2 b6f38c58 00000036
[ 17.429745] 5fa0: c0101204 c0101000 01cd75c0 000089a2 00000008 000089a2 bedadba8 bedadba0
[ 17.437941] 5fc0: 01cd75c0 000089a2 b6f38c58 00000036 01cd75f8 b6f38c58 01cd7764 0003d7a8
[ 17.446139] 5fe0: 0003cd54 bedadb88 000137c4 b6f8339c 60000010 00000008 00000000 00000000
[ 17.454340] [<c066a284>] (br_vlan_enabled) from [<c066fab8>] (dsa_port_vlan_add+0x40/0x88)
[ 17.462629] [<c066fab8>] (dsa_port_vlan_add) from [<c06787b8>] (__switchdev_port_obj_add+0x30/0x8c)
[ 17.471699] [<c06787b8>] (__switchdev_port_obj_add) from [<c06787e0>] (__switchdev_port_obj_add+0x58/0x8c)
[ 17.481377] [<c06787e0>] (__switchdev_port_obj_add) from [<c0678890>] (switchdev_port_obj_add_now+0x7c/0xf0)
[ 17.491228] [<c0678890>] (switchdev_port_obj_add_now) from [<c066df74>] (br_switchdev_port_vlan_add+0x3c/0x44)
[ 17.501254] [<c066df74>] (br_switchdev_port_vlan_add) from [<c066b924>] (__vlan_add+0x50/0x5b4)
[ 17.509974] [<c066b924>] (__vlan_add) from [<c066c7a8>] (nbp_vlan_add+0x210/0x244)
[ 17.517562] [<c066c7a8>] (nbp_vlan_add) from [<c066c8d8>] (nbp_vlan_init+0xfc/0x158)
[ 17.525326] [<c066c8d8>] (nbp_vlan_init) from [<c065c328>] (br_add_if+0x3c8/0x5ac)
[ 17.532918] [<c065c328>] (br_add_if) from [<c05947cc>] (dev_ifsioc+0x36c/0x390)
[ 17.540245] [<c05947cc>] (dev_ifsioc) from [<c0594e68>] (dev_ioctl+0x5cc/0x63c)
[ 17.547572] [<c0594e68>] (dev_ioctl) from [<c0551c24>] (sock_ioctl+0x52c/0x5a8)
[ 17.554900] [<c0551c24>] (sock_ioctl) from [<c0225788>] (do_vfs_ioctl+0x828/0x8c8)
[ 17.562488] [<c0225788>] (do_vfs_ioctl) from [<c022585c>] (ksys_ioctl+0x34/0x58)
[ 17.569902] [<c022585c>] (ksys_ioctl) from [<c0101000>] (ret_fast_syscall+0x0/0x54)
[ 17.577574] Exception stack(0xed615fa8 to 0xed615ff0)
[ 17.582637] 5fa0: 01cd75c0 000089a2 00000008 000089a2 bedadba8 bedadba0
[ 17.590835] 5fc0: 01cd75c0 000089a2 b6f38c58 00000036 01cd75f8 b6f38c58 01cd7764 0003d7a8
[ 17.599030] 5fe0: 0003cd54 bedadb88 000137c4 b6f8339c
[ 17.604095] Code: 18bd8010 e05c0002 13a00001 e8bd8010 (e5d00518)
[ 17.610211] ---[ end trace 9ac484c1994602dc ]---
[ 17.614842] Kernel panic - not syncing: Fatal exception
[ 17.620079] CPU0: stopping
[ 17.622795] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G D 4.19.82 #0
[ 17.630206] Hardware name: Marvell Armada 380/385 (Device Tree)
[ 17.636146] [<c010ea7c>] (unwind_backtrace) from [<c010a9bc>] (show_stack+0x10/0x14)
[ 17.643910] [<c010a9bc>] (show_stack) from [<c067c6d8>] (dump_stack+0x84/0x98)
[ 17.651150] [<c067c6d8>] (dump_stack) from [<c010d61c>] (handle_IPI+0xf0/0x19c)
[ 17.658482] [<c010d61c>] (handle_IPI) from [<c03ba714>] (gic_handle_irq+0x74/0x78)
[ 17.666071] [<c03ba714>] (gic_handle_irq) from [<c0101a0c>] (__irq_svc+0x6c/0x90)
[ 17.673570] Exception stack(0xc0a01f30 to 0xc0a01f78)
[ 17.678632] 1f20: 00000000 000424d0 ef6d7304 c0114480
[ 17.686829] 1f40: c0a00000 c0a03c6c 00000000 c0a03cac c0944500 00000000 00000000 c0a01f88
[ 17.695025] 1f60: c0a0ed00 c0a01f80 c01082f8 c01082fc 60000013 ffffffff
[ 17.701658] [<c0101a0c>] (__irq_svc) from [<c01082fc>] (arch_cpu_idle+0x34/0x38)
[ 17.709076] [<c01082fc>] (arch_cpu_idle) from [<c014c598>] (do_idle+0xd8/0x1b4)
[ 17.716403] [<c014c598>] (do_idle) from [<c014c8d0>] (cpu_startup_entry+0x18/0x1c)
[ 17.723993] [<c014c8d0>] (cpu_startup_entry) from [<c0900df8>] (start_kernel+0x4f4/0x504)
[ 17.732190] Rebooting in 3 seconds..
|
|
26.11.2019 | 2634 | Base system | Bug Report | Very Low | Critical | Luci allows access if root password is cleared and lock... | All | Unconfirmed |
Task Description
Luci doesn’t correctly handle a disabled, empty password for root. Deleting and disabling the root password makes the luci interface accessible without a password.
Steps to reproduce: - Delete root password (passwd -d root) - Lock root password (passwd -l root) - Try to access Luci
|
|
08.01.2020 | 2718 | Base system | Bug Report | Very Low | Critical | /overlay is empty and nothing can be written there | Trunk | Unconfirmed |
Task Description
Supply the following if possible: - Device problem occurs on
Only on TPLink Archer C7 v5 (current model). Other models are OK: A7 (”V5”) (also current), C7 V2, C7 V4 (both earlier)
- Software versions of OpenWrt/LEDE release, packages, etc.
Only Trunk has this problem, and only on C7 v5. rc19.07 does *not* have this problem.
- Steps to reproduce
make menuconfig for target C7 V5 load squashfs-factory version in a C7 V5 boot
...and presto, there’s nothing in /overlay. /rom/overlay is populated. I have found no way to write anything on /overlay. Luci can’t save anything either – not even a password.
There’s nothing weird in my make menuconfig config, unless you count python3-light, bind-dig, ca-certificates, etc. as weird. And the other C7 and C7-like models work fine.
|
|
05.02.2020 | 2812 | Base system | Bug Report | Very Low | Critical | Xiaomi router 3g Openwrt V19 problem. Upload very low. | openwrt-19.07 | Unconfirmed |
Task Description
Hello, I have xiaomi router 3g, I installed OpenWrt v18 and everything perfect, perfect speed, perfect management (although improvable) etc ... The problem comes when upgrading to v19.07 and v19.07.1, the router’s upload speed low by half (wired 600mbs v18) v19 300mbs upload speed .... it looks like a bug and it happens to many people , is there any solution to this? Is it possible to improve the router driver and improve the upload and full management of v19? thanks.
|
|
13.02.2020 | 2832 | Base system | Bug Report | Very Low | Critical | D-link DIR-885L firmware doesn't match due to regional ... | openwrt-19.07 | Unconfirmed |
Task Description
According to the hardware support list, D-link DIR-885L HW A1 is supported, therefore, I have acquired one in China, it clearly stated the HW revision is A1 but its WIFI is not supported with the original firmware 19.07.1
after I flashed the firmware in discovery mode , the wireless tab is not shown in the system. Checked wifi configuration and the file was empty. I found there’s another driver for A2 hardware in the product page, I downloaded it, put it in the designated directory, restarted the router and my wifi appears.
but the driver doesn’t work well. The 2.4g (radio0) can not be started most of the time, some time I alter the configuration of radio0 might bring it up, but even I’ve managed to find the SSID, I can’t connect it. always prompt wrong password.
the 5g (radio1) is better. if I fix the channel, restart the router every time I change the configuration (even change password), it usually make the router works.
I think the Device sold in China is different from other area, the default firmware (which supports A1) doesn’t support Chinese A1 hardware, the A2 firmware driver (BCM4366c) supports the Chinese A1 hardware but doesn’t work well since the driver was dated 2017.
with this BCM4366C driver provided in A2 firmware, I can only have 5G fix Channel WPA2 security wifi service, it’s usable, but all other function are not working, not even one.
I opened the router, tried to provide the chip information but the chips are covered by metal jacket and fixed to the mother board. I have manufacture’s original latest firmware, I think the proper driver may be extracted from it but I’m not capable to do it. I can provide the file as requested. Can’t post here, the file is too big.
|
|
08.04.2020 | 2979 | Base system | Bug Report | Very Low | Critical | Banana Pi R64 can not upgrade on sysupgrade image | Trunk | Unconfirmed |
Task Description
When I am try update initramfs image to sysupgrade. After command sysupgrade I am get error: Sysupgrade is not supported on your board yet. Device: Banana PI R64 Build: Development Snapshot from Wed Apr 8 02:31:30 2020
|
|
08.04.2020 | 2981 | Base system | Bug Report | Very Low | Critical | no switch0 device on Xiaomi Mi Router 3G (and V2) | Trunk | Unconfirmed |
Task Description
Apparently since kernel 5.4, the switch0 is not working correctly anymore. With a plain network config, ethernet ports are available. When using VLAN, the ports don’t work anymore; even the LEDs are off. Luci → Network: no switch option available
root@test:/# swconfig list
root@test:/#
Devices: Xioami Mi Router 3G and Xiaomi Mi Router 3G V2 Tested with both devices. Tested with plain git checkout and my own build environment (master). Always the same behaviour...
boot log:
<## Booting image at bc180000 ...
Image Name: MIPS dl3it-mi3g Linux-5.4.28
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 2102189 Bytes = 2 MB
Load Address: 80001000
Entry Point: 80001000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Erasing SPI Flash...
raspi_erase: offs:30000 len:10000
.
Writing to SPI Flash...
.
done
commandline uart_en=0 factory_mode=0 mem=128m root=/dev/mtdblock9
No initrd
## Transferring control to Linux (at address 80001000) ...
## Giving linux memsize in MB, 128
Starting kernel ...
[ 0.000000] Linux version 5.4.28 (dl3it-mi3g@mySpace) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r12868-c948a4782b)) #0 SMP Wed Apr 8 13:05:51 2020
[ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[ 0.000000] printk: bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[ 0.000000] MIPS: machine is Xiaomi Mi Router 3G v2
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] VPE topology {2,2} total 4
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] HighMem empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] percpu: Embedded 14 pages/cpu s26480 r8192 d22672 u57344
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,jffs2
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 0.000000] Writing ErrCtl register=000400d0
[ 0.000000] Readback ErrCtl register=000400d0
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 122004K/131072K available (5291K kernel code, 173K rwdata, 688K rodata, 1260K init, 224K bss, 9068K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[ 0.000000] NR_IRQS: 256
[ 0.000000] random: get_random_bytes called from 0x80605a08 with crng_init=0
[ 0.000000] CPU Clock: 880MHz
[ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns
[ 0.000009] sched_clock: 32 bits at 440MHz, resolution 2ns, wraps every 4880645118ns
[ 0.007802] Calibrating delay loop... 583.68 BogoMIPS (lpj=1167360)
[ 0.042004] pid_max: default: 32768 minimum: 301
[ 0.046743] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.053968] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.063838] rcu: Hierarchical SRCU implementation.
[ 0.069180] smp: Bringing up secondary CPUs ...
[ 0.075309] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.075319] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.075331] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.075432] CPU1 revision is: 0001992f (MIPS 1004Kc)
[ 0.101936] Synchronize counters for CPU 1: done.
[ 0.142926] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.142934] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.142942] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.143000] CPU2 revision is: 0001992f (MIPS 1004Kc)
[ 0.166600] Synchronize counters for CPU 2: done.
[ 0.197977] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.197985] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.197994] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.198055] CPU3 revision is: 0001992f (MIPS 1004Kc)
[ 0.224458] Synchronize counters for CPU 3: done.
[ 0.254333] smp: Brought up 1 node, 4 CPUs
[ 0.262078] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.271788] futex hash table entries: 1024 (order: 3, 32768 bytes, linear)
[ 0.278766] pinctrl core: initialized pinctrl subsystem
[ 0.285406] NET: Registered protocol family 16
[ 0.310358] random: fast init done
[ 0.318567] clocksource: Switched to clocksource GIC
[ 0.325345] NET: Registered protocol family 2
[ 0.330315] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[ 0.338626] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.346200] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear)
[ 0.353202] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.359629] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.366103] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.373226] NET: Registered protocol family 1
[ 0.377532] PCI: CLS 0 bytes, default 32
[ 0.470541] 4 CPUs re-calibrate udelay(lpj = 1163264)
[ 0.477001] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[ 0.492348] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.498111] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.510897] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 0.516745] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 0.522559] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 0.528863] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
[ 0.536441] printk: console [ttyS0] disabled
[ 0.540734] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A
[ 0.549720] printk: console [ttyS0] enabled
[ 0.549720] printk: console [ttyS0] enabled
[ 0.557980] printk: bootconsole [early0] disabled
[ 0.557980] printk: bootconsole [early0] disabled
[ 0.569760] spi-mt7621 1e000b00.spi: sys_freq: 220000000
[ 0.577944] spi-nor spi0.0: gd25q128 (16384 Kbytes)
[ 0.582936] 8 fixed-partitions partitions found on MTD device spi0.0
[ 0.589281] Creating 8 MTD partitions on "spi0.0":
[ 0.594079] 0x000000000000-0x000000030000 : "u-boot"
[ 0.600206] 0x000000030000-0x000000040000 : "u-boot-env"
[ 0.606677] 0x000000040000-0x000000050000 : "Bdata"
[ 0.612654] 0x000000050000-0x000000060000 : "factory"
[ 0.618871] 0x000000060000-0x000000070000 : "crash"
[ 0.624841] 0x000000070000-0x000000080000 : "cfg_bak"
[ 0.631048] 0x000000080000-0x000000180000 : "overlay"
[ 0.637248] 0x000000180000-0x000001000000 : "firmware"
[ 0.643805] 2 uimage-fw partitions found on MTD device firmware
[ 0.649771] Creating 2 MTD partitions on "firmware":
[ 0.654751] 0x000000000000-0x0000002013ed : "kernel"
[ 0.660846] 0x0000002013ed-0x000000e80000 : "rootfs"
[ 0.666945] mtd: device 9 (rootfs) set to be root filesystem
[ 0.672703] 1 squashfs-split partitions found on MTD device rootfs
[ 0.678890] 0x0000009c0000-0x000000e80000 : "rootfs_data"
[ 0.686092] libphy: Fixed MDIO Bus: probed
[ 0.716870] libphy: mdio: probed
[ 0.720379] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
[ 0.727570] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 21
[ 0.738011] mt7621-pci 1e140000.pcie: Parsing DT failed
[ 0.745444] NET: Registered protocol family 10
[ 0.751473] Segment Routing with IPv6
[ 0.755297] NET: Registered protocol family 17
[ 0.760014] 8021q: 802.1Q VLAN Support v1.8
[ 0.765966] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
[ 1.374877] libphy: dsa slave smi: probed
[ 1.438599] mt7530 mdio-bus:1f lan2 (uninitialized): PHY [dsa-0.0:02] driver [Generic PHY]
[ 1.458608] mt7530 mdio-bus:1f lan1 (uninitialized): PHY [dsa-0.0:03] driver [Generic PHY]
[ 1.478606] mt7530 mdio-bus:1f wan (uninitialized): PHY [dsa-0.0:04] driver [Generic PHY]
[ 1.534553] mt7530 mdio-bus:1f: configuring for fixed/rgmii link mode
[ 2.150548] mt7530 mdio-bus:1f: Link is Up - 1Gbps/Full - flow control off
[ 2.226584] DSA: tree 0 setup
[ 2.229877] rt2880-pinmux pinctrl: pcie is already enabled
[ 2.235383] mt7621-pci 1e140000.pcie: Error applying setting, reverse things back
[ 2.243000] mt7621-pci-phy 1e149000.pcie-phy: PHY for 0xbe149000 (dual port = 1)
[ 2.250551] mt7621-pci-phy 1e14a000.pcie-phy: PHY for 0xbe14a000 (dual port = 0)
[ 2.357677] mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz
[ 2.363264] mt7621-pci-phy 1e14a000.pcie-phy: Xtal is 40MHz
[ 2.468514] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK)
[ 2.475474] mt7621-pci 1e140000.pcie: PCIE0 enabled
[ 2.480348] mt7621-pci 1e140000.pcie: PCIE1 enabled
[ 2.485228] mt7621-pci 1e140000.pcie: PCI coherence region base: 0x60000000, mask/settings: 0xf0000002
[ 2.494703] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00
[ 2.501072] pci_bus 0000:00: root bus resource [io 0x1e160000-0x1e16ffff]
[ 2.507943] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[ 2.514813] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 2.520334] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400
[ 2.526365] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 2.532635] pci 0000:00:00.0: reg 0x14: [mem 0x60400000-0x6040ffff]
[ 2.538968] pci 0000:00:00.0: supports D1
[ 2.542981] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 2.549116] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400
[ 2.555169] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 2.561435] pci 0000:00:01.0: reg 0x14: [mem 0x60410000-0x6041ffff]
[ 2.567758] pci 0000:00:01.0: supports D1
[ 2.571771] pci 0000:00:01.0: PME# supported from D0 D1 D3hot
[ 2.579056] pci 0000:01:00.0: [14c3:7662] type 00 class 0x028000
[ 2.585128] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit]
[ 2.591952] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[ 2.598749] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[ 2.606100] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 2.611344] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff]
[ 2.617432] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 2.624216] pci 0000:00:00.0: bridge window [mem 0x60100000-0x601fffff pref]
[ 2.631434] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 2.638265] pci 0000:02:00.0: [14c3:7603] type 00 class 0x028000
[ 2.644325] pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x000fffff]
[ 2.650726] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
[ 2.658077] pci 0000:00:01.0: PCI bridge to [bus 02-ff]
[ 2.663322] pci 0000:00:01.0: bridge window [io 0x0000-0x0fff]
[ 2.669410] pci 0000:00:01.0: bridge window [mem 0x60200000-0x602fffff]
[ 2.676194] pci 0000:00:01.0: bridge window [mem 0x60300000-0x603fffff pref]
[ 2.683420] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[ 2.690083] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[ 2.696693] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[ 2.703651] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000]
[ 2.710254] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000]
[ 2.717213] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[ 2.723998] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x601fffff pref]
[ 2.731215] pci 0000:00:01.0: BAR 8: assigned [mem 0x60200000-0x602fffff]
[ 2.737997] pci 0000:00:01.0: BAR 9: assigned [mem 0x60300000-0x603fffff pref]
[ 2.745215] pci 0000:00:00.0: BAR 1: assigned [mem 0x60400000-0x6040ffff]
[ 2.752006] pci 0000:00:01.0: BAR 1: assigned [mem 0x60410000-0x6041ffff]
[ 2.758795] pci 0000:00:00.0: BAR 7: assigned [io 0x1e160000-0x1e160fff]
[ 2.765577] pci 0000:00:01.0: BAR 7: assigned [io 0x1e161000-0x1e161fff]
[ 2.772372] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit]
[ 2.779687] pci 0000:01:00.0: BAR 6: assigned [mem 0x60100000-0x6010ffff pref]
[ 2.786903] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 2.791867] pci 0000:00:00.0: bridge window [io 0x1e160000-0x1e160fff]
[ 2.798649] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 2.805429] pci 0000:00:00.0: bridge window [mem 0x60100000-0x601fffff pref]
[ 2.812657] pci 0000:02:00.0: BAR 0: assigned [mem 0x60200000-0x602fffff]
[ 2.819442] pci 0000:00:01.0: PCI bridge to [bus 02]
[ 2.824405] pci 0000:00:01.0: bridge window [io 0x1e161000-0x1e161fff]
[ 2.831188] pci 0000:00:01.0: bridge window [mem 0x60200000-0x602fffff]
[ 2.837966] pci 0000:00:01.0: bridge window [mem 0x60300000-0x603fffff pref]
[ 2.845884] hctosys: unable to open rtc device (rtc0)
[ 2.854774] VFS: Mounted root (squashfs filesystem) readonly on device 31:9.
[ 2.865727] Freeing unused kernel memory: 1260K
[ 2.870309] This architecture does not have kernel memory protection.
[ 2.876743] Run /sbin/init as init process
[ 3.287646] init: Console is alive
[ 3.291282] init: - watchdog -
[ 4.502146] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 4.642663] usbcore: registered new interface driver usbfs
[ 4.648277] usbcore: registered new interface driver hub
[ 4.653761] usbcore: registered new device driver usb
[ 4.687605] SCSI subsystem initialized
[ 4.700291] xhci-mtk 1e1c0000.xhci: 1e1c0000.xhci supply vbus not found, using dummy regulator
[ 4.709018] xhci-mtk 1e1c0000.xhci: 1e1c0000.xhci supply vusb33 not found, using dummy regulator
[ 4.717973] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
[ 4.723320] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 1
[ 4.738712] xhci-mtk 1e1c0000.xhci: hcc params 0x01401198 hci version 0x96 quirks 0x0000000000210010
[ 4.747932] xhci-mtk 1e1c0000.xhci: irq 20, io mem 0x1e1c0000
[ 4.754929] hub 1-0:1.0: USB hub found
[ 4.758772] hub 1-0:1.0: 2 ports detected
[ 4.763366] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
[ 4.768728] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 2
[ 4.776220] xhci-mtk 1e1c0000.xhci: Host supports USB 3.0 SuperSpeed
[ 4.782759] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 4.791649] hub 2-0:1.0: USB hub found
[ 4.795501] hub 2-0:1.0: 1 port detected
[ 4.806463] usbcore: registered new interface driver usb-storage
[ 4.812799] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 4.830880] init: - preinit -
[ 5.556493] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
[ 5.564803] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 5.573306] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 5.758344] random: jshn: uninitialized urandom read (4 bytes read)
[ 5.857508] random: jshn: uninitialized urandom read (4 bytes read)
[ 5.892574] random: jshn: uninitialized urandom read (4 bytes read)
[ 6.182562] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode
[ 6.214670] 8021q: adding VLAN 0 to HW filter on device lan1
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 10.454588] mt7530 mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control off
[ 10.461993] IPv6: ADDRCONF(NETDEV_CHANGE): lan1: link becomes ready
[ 10.497376] jffs2: notice: (593) jffs2_build_xattr_subsystem: complete building xattr subsystem, 12 of xdatum (10 unchecked, 2 orphan) and 14 of xref (2 dead, 0 orphan) found.
[ 10.514983] mount_root: switching to jffs2 overlay
[ 10.541029] overlayfs: upper fs does not support tmpfile.
[ 10.553353] urandom-seed: Seeding with /etc/urandom.seed
[ 10.710556] mt7530 mdio-bus:1f lan1: Link is Down
[ 10.794276] procd: - early -
[ 10.797283] procd: - watchdog -
[ 11.390731] procd: - watchdog -
[ 11.394174] procd: - ubus -
[ 11.495821] urandom_read: 5 callbacks suppressed
[ 11.495833] random: ubusd: uninitialized urandom read (4 bytes read)
[ 11.508640] random: ubusd: uninitialized urandom read (4 bytes read)
[ 11.516312] procd: - init -
Please press Enter to activate this console.
[ 11.847029] random: crng init done
[ 12.196458] kmodloader: loading kernel modules from /etc/modules.d/*
[ 12.277843] Key type dns_resolver registered
[ 12.294374] RPC: Registered named UNIX socket transport module.
[ 12.300415] RPC: Registered udp transport module.
[ 12.305113] RPC: Registered tcp transport module.
[ 12.309806] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 12.326652] tun: Universal TUN/TAP device driver, 1.6
[ 12.343512] urngd: v1.0.2 started.
[ 12.353986] NFS: Registering the id_resolver key type
[ 12.359125] Key type id_resolver registered
[ 12.363309] Key type id_legacy registered
[ 12.409615] Loading modules backported from Linux version v5.4.27-0-g585e0cc08069
[ 12.417142] Backport generated by backports.git v5.4.27-1-0-gf6e8852f
[ 12.436131] wireguard: WireGuard 1.0.20200401 loaded. See www.wireguard.com for information.
[ 12.444603] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
[ 12.461355] xt_time: kernel timezone is -0000
[ 12.526918] pci 0000:00:01.0: enabling device (0006 -> 0007)
[ 12.532626] mt7603e 0000:02:00.0: enabling device (0000 -> 0002)
[ 12.538852] mt7603e 0000:02:00.0: ASIC revision: 76030010
[ 13.163810] mt7603e 0000:02:00.0: Firmware Version: ap_pcie
[ 13.169406] mt7603e 0000:02:00.0: Build Time: 20160107100755
[ 13.198554] mt7603e 0000:02:00.0: firmware init done
[ 13.396912] pci 0000:00:00.0: enabling device (0006 -> 0007)
[ 13.402664] mt76x2e 0000:01:00.0: enabling device (0000 -> 0002)
[ 13.408975] mt76x2e 0000:01:00.0: ASIC revision: 76120044
[ 13.890858] mt76x2e 0000:01:00.0: ROM patch build: 20141115060606a
[ 13.905566] mt76x2e 0000:01:00.0: Firmware Version: 0.0.00
[ 13.911181] mt76x2e 0000:01:00.0: Build: 1
[ 13.915314] mt76x2e 0000:01:00.0: Build Time: 201507311614____
[ 13.938667] mt76x2e 0000:01:00.0: Firmware running!
[ 13.975037] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 19.857666] mtk_soc_eth 1e100000.ethernet eth0: Link is Down
[ 20.437833] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
[ 20.448515] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 20.457303] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 20.470323] br-gast: port 1(eth0.119) entered blocking state
[ 20.476130] br-gast: port 1(eth0.119) entered disabled state
[ 20.482797] device eth0.119 entered promiscuous mode
[ 20.487821] device eth0 entered promiscuous mode
[ 20.496672] br-gast: port 1(eth0.119) entered blocking state
[ 20.502388] br-gast: port 1(eth0.119) entered forwarding state
[ 20.610001] br-iot: port 1(eth0.120) entered blocking state
[ 20.615694] br-iot: port 1(eth0.120) entered disabled state
[ 20.621937] device eth0.120 entered promiscuous mode
[ 20.631403] br-iot: port 1(eth0.120) entered blocking state
[ 20.637077] br-iot: port 1(eth0.120) entered forwarding state
[ 20.756696] br-lan: port 1(eth0.117) entered blocking state
[ 20.762433] br-lan: port 1(eth0.117) entered disabled state
[ 20.769851] device eth0.117 entered promiscuous mode
[ 20.780577] br-lan: port 1(eth0.117) entered blocking state
[ 20.786261] br-lan: port 1(eth0.117) entered forwarding state
[ 20.903708] br-media: port 1(eth0.118) entered blocking state
[ 20.909789] br-media: port 1(eth0.118) entered disabled state
[ 20.916212] device eth0.118 entered promiscuous mode
[ 20.924455] br-media: port 1(eth0.118) entered blocking state
[ 20.930260] br-media: port 1(eth0.118) entered forwarding state
[ 21.021138] br-rapw: port 1(eth0.128) entered blocking state
[ 21.027159] br-rapw: port 1(eth0.128) entered disabled state
[ 21.033622] device eth0.128 entered promiscuous mode
[ 21.042842] br-rapw: port 1(eth0.128) entered blocking state
[ 21.048592] br-rapw: port 1(eth0.128) entered forwarding state
[ 24.551924] br-lan: port 2(wlan1) entered blocking state
[ 24.557320] br-lan: port 2(wlan1) entered disabled state
[ 24.563518] device wlan1 entered promiscuous mode
[ 24.640154] br-lan: port 3(wlan0) entered blocking state
[ 24.645515] br-lan: port 3(wlan0) entered disabled state
[ 24.651714] device wlan0 entered promiscuous mode
[ 24.657070] br-lan: port 3(wlan0) entered blocking state
[ 24.662453] br-lan: port 3(wlan0) entered forwarding state
[ 25.927299] br-lan: port 3(wlan0) entered disabled state
[ 25.933474] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 25.940330] br-lan: port 2(wlan1) entered blocking state
[ 25.945682] br-lan: port 2(wlan1) entered forwarding state
[ 25.961147] br-gast: port 2(wlan1-1) entered blocking state
[ 25.966815] br-gast: port 2(wlan1-1) entered disabled state
[ 25.973281] device wlan1-1 entered promiscuous mode
[ 25.980340] br-gast: port 2(wlan1-1) entered blocking state
[ 25.986013] br-gast: port 2(wlan1-1) entered forwarding state
[ 26.602100] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1-1: link becomes ready
[ 26.615326] br-iot: port 2(wlan1-2) entered blocking state
[ 26.620895] br-iot: port 2(wlan1-2) entered disabled state
[ 26.627238] device wlan1-2 entered promiscuous mode
[ 26.633956] br-iot: port 2(wlan1-2) entered blocking state
[ 26.639547] br-iot: port 2(wlan1-2) entered forwarding state
[ 26.654413] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 26.661418] br-lan: port 3(wlan0) entered blocking state
[ 26.666839] br-lan: port 3(wlan0) entered forwarding state
[ 26.684260] br-gast: port 3(wlan0-1) entered blocking state
[ 26.689898] br-gast: port 3(wlan0-1) entered disabled state
[ 26.696257] device wlan0-1 entered promiscuous mode
[ 26.703570] br-gast: port 3(wlan0-1) entered blocking state
[ 26.709197] br-gast: port 3(wlan0-1) entered forwarding state
[ 26.950979] br-iot: port 2(wlan1-2) entered disabled state
[ 26.958856] br-gast: port 3(wlan0-1) entered disabled state
[ 27.183822] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1-2: link becomes ready
[ 27.190950] br-iot: port 2(wlan1-2) entered blocking state
[ 27.196513] br-iot: port 2(wlan1-2) entered forwarding state
[ 27.287694] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0-1: link becomes ready
[ 27.294743] br-gast: port 3(wlan0-1) entered blocking state
[ 27.300358] br-gast: port 3(wlan0-1) entered forwarding state
[ 27.314616] br-iot: port 3(wlan0-2) entered blocking state
[ 27.320314] br-iot: port 3(wlan0-2) entered disabled state
[ 27.326962] device wlan0-2 entered promiscuous mode
[ 27.333493] br-iot: port 3(wlan0-2) entered blocking state
[ 27.339125] br-iot: port 3(wlan0-2) entered forwarding state
[ 27.763549] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0-2: link becomes ready
[ 27.777443] br-rapw: port 2(wlan0-3) entered blocking state
[ 27.783263] br-rapw: port 2(wlan0-3) entered disabled state
[ 27.789570] device wlan0-3 entered promiscuous mode
[ 27.796480] br-rapw: port 2(wlan0-3) entered blocking state
[ 27.802127] br-rapw: port 2(wlan0-3) entered forwarding state
[ 27.954752] br-rapw: port 2(wlan0-3) entered disabled state
[ 28.219373] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0-3: link becomes ready
[ 28.226593] br-rapw: port 2(wlan0-3) entered blocking state
[ 28.232216] br-rapw: port 2(wlan0-3) entered forwarding state
kernel modules:
root@test:/# lsmod
cfg80211 258960 4 mt76x02_lib,mt7603e,mt76,mac80211
compat 608 2 mac80211,cfg80211
crc_ccitt 1696 0
crc32c_generic 1376 0
dns_resolver 4272 1 nfsv4
ext4 413584 0
fat 58208 1 vfat
gpio_button_hotplug 6944 0
grace 1328 1 lockd
ip_set 25744 16 xt_set,ip_set_list_set,ip_set_hash_netportnet,ip_set_hash_netport,ip_set_hash_netnet,ip_set_hash_netiface,ip_set_hash_net,ip_set_hash_mac,ip_set_hash_ipportnet,ip_set_hash_ipportip,ip_set_hash_ipport,ip_set_hash_ipmark,ip_set_hash_ip,ip_set_bitmap_port,ip_set_bitmap_ipmac,ip_set_bitmap_ip
ip_set_bitmap_ip 6976 0
ip_set_bitmap_ipmac 7200 0
ip_set_bitmap_port 6176 0
ip_set_hash_ip 26176 0
ip_set_hash_ipmark 26400 0
ip_set_hash_ipport 26976 0
ip_set_hash_ipportip 28000 0
ip_set_hash_ipportnet 32576 0
ip_set_hash_mac 13632 0
ip_set_hash_net 29696 0
ip_set_hash_netiface 31264 0
ip_set_hash_netnet 32832 0
ip_set_hash_netport 31104 0
ip_set_hash_netportnet 33952 0
ip_set_list_set 7232 0
ip_tables 10848 3 iptable_nat,iptable_mangle,iptable_filter
ip6_tables 10624 2 ip6table_mangle,ip6table_filter
ip6_udp_tunnel 1760 1 wireguard
ip6t_REJECT 1248 2
ip6table_filter 704 1
ip6table_mangle 1184 1
ipt_REJECT 1184 2
iptable_filter 672 1
iptable_mangle 896 1
iptable_nat 768 1
jbd2 56368 1 ext4
leds_gpio 3040 0
ledtrig_heartbeat 1520 0
ledtrig_usbport 2864 0
lockd 55232 1 nfs
mac80211 496000 4 mt76x2e,mt76x02_lib,mt7603e,mt76
mbcache 3952 1 ext4
mt76 32096 4 mt76x2e,mt76x2_common,mt76x02_lib,mt7603e
mt7603e 38080 0
mt76x02_lib 39872 2 mt76x2e,mt76x2_common
mt76x2_common 11360 1 mt76x2e
mt76x2e 10080 0
nf_conntrack 71280 9 xt_state,xt_nat,xt_conntrack,xt_REDIRECT,xt_MASQUERADE,nf_nat,nf_flow_table,nf_conntrack_rtcache,nf_conntrack_netlink
nf_conntrack_netlink 24112 0
nf_conntrack_rtcache 2400 0
nf_defrag_ipv4 1120 1 nf_conntrack
nf_defrag_ipv6 4976 1 nf_conntrack
nf_flow_table 14864 2 xt_FLOWOFFLOAD,nf_flow_table_hw
nf_flow_table_hw 2416 1
nf_log_common 2624 2 nf_log_ipv4,nf_log_ipv6
nf_log_ipv4 3520 0
nf_log_ipv6 4192 0
nf_nat 23056 4 iptable_nat,xt_nat,xt_REDIRECT,xt_MASQUERADE
nf_reject_ipv4 2112 1 ipt_REJECT
nf_reject_ipv6 2464 1 ip6t_REJECT
nfnetlink 4560 2 nf_conntrack_netlink,ip_set
nfs 127680 1 nfsv4
nfsv4 139152 0
nls_base 5424 6 vfat,fat,nls_utf8,nls_iso8859_1,nls_cp437,usbcore
nls_cp437 4416 0
nls_iso8859_1 2880 0
nls_utf8 864 0
scsi_mod 86320 2 usb_storage,sd_mod
sd_mod 29104 0
sunrpc 174064 3 nfsv4,nfs,lockd
swconfig 9680 0
tun 32640 0
udp_tunnel 2560 1 wireguard
usb_common 2704 3 xhci_plat_hcd,xhci_hcd,usbcore
usb_storage 39888 0
usbcore 140176 6 ledtrig_usbport,usb_storage,xhci_plat_hcd,xhci_pci,xhci_mtk,xhci_hcd
vfat 10016 0
wireguard 85792 0
x_tables 15472 24 xt_state,xt_nat,xt_conntrack,xt_REDIRECT,xt_MASQUERADE,xt_FLOWOFFLOAD,ipt_REJECT,xt_time,xt_tcpudp,xt_multiport,xt_mark,xt_mac,xt_limit,xt_comment,xt_TCPMSS,xt_LOG,iptable_mangle,iptable_filter,ip_tables,xt_set,ip6table_mangle,ip6table_filter,ip6_tables,ip6t_REJECT
xhci_hcd 113408 3 xhci_plat_hcd,xhci_pci,xhci_mtk
xhci_mtk 4800 0
xhci_pci 3424 0
xhci_plat_hcd 5600 0
xt_FLOWOFFLOAD 3152 0
xt_LOG 768 0
xt_MASQUERADE 832 0
xt_REDIRECT 704 0
xt_TCPMSS 3168 2
xt_comment 512183
xt_conntrack 2432 24
xt_limit 1312 2
xt_mac 640 0
xt_mark 672 0
xt_multiport 1312 0
xt_nat 2432 0
xt_set 7328 0
xt_state 832 0
xt_tcpudp 1824 18
xt_time 1952 0
root@test:/#
Routers work fine with kernel 4.14.xxx
|
|
10.04.2020 | 2989 | Base system | Bug Report | Very Low | Critical | Boots but no connection can be made to router | Trunk | Unconfirmed |
Task Description
Hardware: ZBT WG3526 16MB RAM Image file: openwrt-ramips-mt7621-zbtlink_zbt-wg3526-16m-squashfs-sysupgrade.bin Image Date Stamp: Snapshot Fri Apr 10 06:55:59 2020
Issue: Flashes without issues.
Boots but no connection can be made to router using web browser I/F, WinSCP or PuTTY.
Not responding to ping 192.168.1.1.
All LAN and WAN ports LED's are flashing.
No Internet connection (WAN)
|
|
02.05.2020 | 3060 | Base system | Bug Report | Very Low | Critical | Flashing current trunk on NBG6616 results in bootloop | Trunk | Unconfirmed |
Task Description
Installing current trunk esults in bootloop. First I tried to install it over stock firmware with recovery/tftp but it was stuck in bootloop. Then I reinstalled 19.07.02 via recovery/tftp - which worked fine. After that, I tried to install trunk via recovery/tftp, but it also gave bootloop.
The symptoms looks like the ones mentioned below. The problem was fixed, and maybee the same solution is missing in trunk
FS#168 - Firmware dont boot up on Zyxel NBG6616
FS#1724 - 18.06.0 release not working on ZyXEL NBG6616 (ar71xx) https://forum.openwrt.org/t/nbg6616-wan-device-snapshot-bootloop/53944 https://forum.openwrt.org/t/zyxel-nbg6616-bootloop-in-18-0-6-and-18-0-6-1/19355
|
|
10.05.2020 | 3087 | Base system | Bug Report | Very Low | Critical | r13208-426fb8cf84 from downloads.openwrt.org does not b... | Trunk | Unconfirmed |
Task Description
Device problem occurs on
Software versions of OpenWrt/LEDE release, packages, etc.
Steps to reproduce
download given image
flash it via TFTP to routers flash
get attached output
caviat
|
|
18.05.2020 | 3109 | Base system | Bug Report | Very Low | Critical | UBIFS failure/crash on BT HomeHub 2B: __nand_correct_da... | openwrt-19.07 | Unconfirmed |
Task Description
Device: BT HomeHub Version 2B (Lantiq XWAY)
Software: 19.07.3 downloaded from:
https://downloads.openwrt.org/releases/19.07.3/targets/lantiq/xway/openwrt-19.07.3-lantiq-xway-bt_homehub-v2b-squashfs-sysupgrade.bin
After an hour or so of usage, the router reboots itself with a corrupted filesystem. I’ve attached the log to this bug report. The log contains:
__nand_correct_data: uncorrectable ECC error
so I think there might be a link with the similar problem that the BT HomeHub Version 5A had a long time ago, as per:
https://bugs.openwrt.org/index.php?do=details&task_id=245 (”Lede won’t boot on HHB5”)
and
http://openwrt.ebilan.co.uk/viewtopic.php?f=7&t=133#p1022 (post by Mathias Kresin / mkresin who fixed the problem with the Home Hub 5A)
This bug may also be related to:
https://bugs.openwrt.org/index.php?do=details&task_id=1842
(I think that this bug may affect every release since 18.06.0)
|
|
27.05.2020 | 3129 | Base system | Bug Report | Very Low | Critical | UQMI wonāt connect with Private APN | Trunk | Unconfirmed |
Task Description
UQMI wonāt connect with Private APN Hey Folks,
I have a Problem with the QMI protocol.
I bought a private ip from my ISP and can’t connect with the private APN, only the dynamic IP APN works.
With ModemManager the connection to my Private APN works as expected, so no fault on ISP side. With crosscompile Quectel-cm to OpenWRT, the connection with qmi protocol to my Private APN works as expected, so no fault on ISP side.
|
|
05.06.2020 | 3151 | Base system | Bug Report | Very Low | Critical | Kimax U35WF overlay memory | Trunk | Unconfirmed |
Task Description
Kimax Blueendless U35WF Original Kimax firmware
install openwrt-19.07.3-ramips-mt7620-kimax_u35wf-initramfs-kernel.bin problems: IP configuration lost after power up unable to install any package (overlay memory), unable to generate backup firmware config archive (no contents). No version 18.06 available for this model to downgrade.
Flash new firmware image openwrt-19.07.3-ramips-mt7620-kimax_u35wf-squashfs-sysupgrade.bin and ok
|
|
27.06.2020 | 3206 | Base system | Bug Report | Very Low | Critical | sysupgrade from 18.06.8 to 19.07.0..trunk results in a ... | Trunk | Unconfirmed |
Task Description
After a sysupgrade from 18.06.8 to 19.07.0, 19.07.3, or trunk as of 2020-06-28, the router is stuck in an UBI-related boot loop.
Boot log for trunk:
===================================================================
MT7621 stage1 code 10:33:11 (ASIC)
CPU=50000000 HZ BUS=16666666 HZ
==================================================================
Change MPLL source from XTAL to CR...
do MEMPLL setting..
MEMPLL Config : 0x11100000
3PLL mode + External loopback
=== XTAL-40Mhz === DDR-1200Mhz ===
PLL2 FB_DL: 0xf, 1/0 = 634/390 3D000000
PLL4 FB_DL: 0x14, 1/0 = 514/510 51000000
PLL3 FB_DL: 0x1a, 1/0 = 703/321 69000000
do DDR setting..[00320381]
Apply DDR3 Setting...(use customer AC)
0 8 16 24 32 40 48 56 64 72 80 88 96 104 112 120
W: g.applet.interface.uart: 3173 frame or parity errors detected
--------------------------------------------------------------------------------
0000:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0001:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0002:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0003:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0004:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0005:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0006:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0007:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0008:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0009:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
000A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
000B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
000C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
000D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1
000E:| 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
000F:| 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0
0010:| 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
0011:| 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0
0012:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0013:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0014:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0015:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0016:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0017:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0018:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0019:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001E:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001F:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
rank 0 coarse = 16
rank 0 fine = 32
B:| 0 0 0 0 0 0 0 0 1 1 1 0 0 0 0 0
opt_dle value:9
DRAMC_R0DELDLY[018]=00001B1C
==================================================================
RX DQS perbit delay software calibration
==================================================================
1.0-15 bit dq delay value
==================================================================
bit| 0 1 2 3 4 5 6 7 8 9
--------------------------------------
0 | 10 8 10 11 11 7 11 8 8 9
10 | 9 12 7 10 9 11
--------------------------------------
==================================================================
2.dqs window
x=pass dqs delay value (min~max)center
y=0-7bit DQ of every group
input delay:DQS0 =28 DQS1 = 27
==================================================================
bit DQS0 bit DQS1
0 (1~53)27 8 (1~53)27
1 (1~52)26 9 (1~49)25
2 (1~53)27 10 (1~53)27
3 (1~55)28 11 (1~52)26
4 (1~54)27 12 (1~53)27
5 (0~53)26 13 (1~51)26
6 (1~52)26 14 (1~52)26
7 (1~52)26 15 (1~53)27
==================================================================
3.dq delay value last
==================================================================
bit| 0 1 2 3 4 5 6 7 8 9
--------------------------------------
0 | 11 10 11 11 12 9 13 10 8 11
10 | 9 13 7 11 10 11
==================================================================
==================================================================
TX perbyte calibration
==================================================================
DQS loop = 15, cmp_err_1 = ffff0800
dqs_perbyte_dly.last_dqsdly_pass[0]=15, finish count=1
DQS loop = 14, cmp_err_1 = ffff0000
dqs_perbyte_dly.last_dqsdly_pass[1]=14, finish count=2
DQ loop=15, cmp_err_1 = ffff01aa
DQ loop=14, cmp_err_1 = ffff0080
dqs_perbyte_dly.last_dqdly_pass[1]=14, finish count=1
DQ loop=13, cmp_err_1 = ffff0000
dqs_perbyte_dly.last_dqdly_pass[0]=13, finish count=2
byte:0, (DQS,DQ)=(9,8)
byte:1, (DQS,DQ)=(8,8)
20,data:89
[EMI] DRAMC calibration passed
===================================================================
MT7621 stage1 code done
CPU=50000000 HZ BUS=16666666 HZ
===================================================================
U-Boot 1.1.3 (Aug 30 2017 - 02:28:33)
Board: Ralink APSoC DRAM: 256 MB
relocate_code Pointer at: 8ffb0000
Config XHCI 40M PLL
Allocate 16 byte aligned buffer: 8ffe1940
Enable NFI Clock
# MTK NAND # : Use HW ECC
NAND ID [C2 DA 90 95 06]
Device found in MTK table, ID: c2da, EXT_ID: 909506
Support this Device in MTK table! c2da
select_chip
[NAND]select ecc bit:4, sparesize :64 spare_per_sector=16
Signature matched and data read!
load_fact_bbt success 2047
load fact bbt success
[mtk_nand] probe successfully!
mtd->writesize=2048 mtd->oobsize=64, mtd->erasesize=131072 devinfo.iowidth=8
..
UBNT e51 13-02122-14 B4FBE4B3E6EE
UBNT BD type=e51, mac=B4FBE4B3E6EE, s/n=B4FBE4B3E6EE, mrev=14, k_idx=1
============================================
Ralink UBoot Version: 4.3.S.0
--------------------------------------------
ASIC MT7621A DualCore (MAC to MT7530 Mode)
DRAM_CONF_FROM: Auto-Detection
DRAM_TYPE: DDR3
DRAM bus: 16 bit
Xtal Mode=3 OCP Ratio=1/3
Flash component: NAND Flash
Date:Aug 30 2017 Time:02:28:33
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 880 MHZ ####
estimate memory size =256 Mbytes
#Reset_MT7530
Enable port 0
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
default: 3
3
You choosed 3
0
3: System Boot system code via Flash.
## Booting image at c0040000 ...
Image Name: MIPS OpenWrt Linux-5.4.48
Image Type: MIPS Linux Kernel Image (uncompressed)
Data Size: 2435865 Bytes = 2.3 MB
Load Address: 80001000
Entry Point: 80001000
...................................... Verifying Checksum ... OK
OK
No initrd
## Transferring control to Linux (at address 80001000) ...
## Giving linux memsize in MB, 256
Starting kernel ...
OpenWrt kernel loader for MIPS based SoC
Copyright (C) 2011 Gabor Juhos <juhosg@openwrt.org>
Decompressing kernel... done!
Starting kernel at 80001000...
[ 0.000000] Linux version 5.4.48 (builder@buildhost) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r13649-b1d5ab1a69)) #0 SMP Fri Jun 26 22:33:29 2020
[ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[ 0.000000] printk: bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[ 0.000000] MIPS: machine is Ubiquiti EdgeRouter X SFP
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] VPE topology {2,2} total 4
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] HighMem empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] percpu: Embedded 14 pages/cpu s26704 r8192 d22448 u57344
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64960
[ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000] Writing ErrCtl register=00032940
[ 0.000000] Readback ErrCtl register=00032940
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 250536K/262144K available (5846K kernel code, 201K rwdata, 1260K rodata, 1256K init, 237K bss, 11608K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[ 0.000000] NR_IRQS: 256
[ 0.000000] random: get_random_bytes called from start_kernel+0x340/0x558 with crng_init=0
[ 0.000000] CPU Clock: 880MHz
[ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns
[ 0.000009] sched_clock: 32 bits at 440MHz, resolution 2ns, wraps every 4880645118ns
[ 0.015483] Calibrating delay loop... 583.68 BogoMIPS (lpj=1167360)
[ 0.055830] pid_max: default: 32768 minimum: 301
[ 0.065180] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.079586] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.097702] rcu: Hierarchical SRCU implementation.
[ 0.107813] smp: Bringing up secondary CPUs ...
[ 4.135874] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 4.135885] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 4.135897] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 4.135995] CPU1 revision is: 0001992f (MIPS 1004Kc)
[ 0.144999] Synchronize counters for CPU 1: done.
[ 4.226937] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 4.226945] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 4.226952] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 4.227006] CPU2 revision is: 0001992f (MIPS 1004Kc)
[ 0.239460] Synchronize counters for CPU 2: done.
[ 4.318055] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 4.318064] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 4.318072] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 4.318129] CPU3 revision is: 0001992f (MIPS 1004Kc)
[ 0.327061] Synchronize counters for CPU 3: done.
[ 0.386664] smp: Brought up 1 node, 4 CPUs
[ 0.398972] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.418237] futex hash table entries: 1024 (order: 3, 32768 bytes, linear)
[ 0.432169] pinctrl core: initialized pinctrl subsystem
[ 0.443530] NET: Registered protocol family 16
[ 0.481661] clocksource: Switched to clocksource GIC
[ 0.493356] NET: Registered protocol family 2
[ 0.502975] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[ 0.519574] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.534699] TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.548872] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.561648] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.574529] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.588595] NET: Registered protocol family 1
[ 0.597152] PCI: CLS 0 bytes, default 32
[ 0.693612] 4 CPUs re-calibrate udelay(lpj = 1167360)
[ 0.705093] workingset: timestamp_bits=14 max_order=16 bucket_order=2
[ 0.719864] random: fast init done
[ 0.725746] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.738153] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.760502] GPIO line 487 (sfp_i2c_clk_gate) hogged as output/high
[ 0.772946] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 0.784177] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 0.795396] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 0.807068] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.822849] printk: console [ttyS0] disabled
[ 0.831301] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A
[ 0.849226] printk: console [ttyS0] enabled
[ 0.849226] printk: console [ttyS0] enabled
[ 0.865790] printk: bootconsole [early0] disabled
[ 0.865790] printk: bootconsole [early0] disabled
[ 0.886838] mt7621-nand 1e003000.nand: Using programmed access timing: 31c07388
[ 0.901809] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xda
[ 0.914464] nand: Macronix MX30LF2G18AC
[ 0.922100] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 0.937174] mt7621-nand 1e003000.nand: ECC strength adjusted to 4 bits
[ 0.950207] mt7621-nand 1e003000.nand: Using programmed access timing: 21005134
[ 0.964763] mt7621-nand 1e003000.nand: Using programmed access timing: 21005134
[ 0.979322] Scanning device for bad blocks
[ 2.388364] Bad eraseblock 1105 at 0x000008a20000
[ 3.591347] 6 fixed-partitions partitions found on MTD device mt7621-nand
[ 3.604863] Creating 6 MTD partitions on "mt7621-nand":
[ 3.615275] 0x000000000000-0x000000080000 : "u-boot"
[ 3.626464] 0x000000080000-0x0000000e0000 : "u-boot-env"
[ 3.638343] 0x0000000e0000-0x000000140000 : "factory"
[ 3.649566] 0x000000140000-0x000000440000 : "kernel1"
[ 3.660834] 0x000000440000-0x000000740000 : "kernel2"
[ 3.672135] 0x000000740000-0x00000ff00000 : "ubi"
[ 3.684934] libphy: Fixed MDIO Bus: probed
[ 3.720110] libphy: mdio: probed
[ 3.726777] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
[ 3.741399] mtk_soc_eth 1e100000.ethernet dsa: mediatek frame engine at 0xbe100000, irq 20
[ 3.759062] i2c-mt7621 1e000900.i2c: clock 100 kHz
[ 3.772209] NET: Registered protocol family 10
[ 3.782778] Segment Routing with IPv6
[ 3.790195] NET: Registered protocol family 17
[ 3.799123] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 3.825176] 8021q: 802.1Q VLAN Support v1.8
[ 3.835469] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
[ 3.858806] libphy: dsa slave smi: probed
[ 3.867214] mt7530 mdio-bus:1f eth0 (uninitialized): PHY [dsa-0.0:00] driver [Generic PHY]
[ 3.885166] mt7530 mdio-bus:1f eth1 (uninitialized): PHY [dsa-0.0:01] driver [Generic PHY]
[ 3.903046] mt7530 mdio-bus:1f eth2 (uninitialized): PHY [dsa-0.0:02] driver [Generic PHY]
[ 3.920926] mt7530 mdio-bus:1f eth3 (uninitialized): PHY [dsa-0.0:03] driver [Generic PHY]
[ 3.938853] mt7530 mdio-bus:1f eth4 (uninitialized): PHY [dsa-0.0:04] driver [Generic PHY]
[ 3.956767] mt7530 mdio-bus:1f eth5 (uninitialized): PHY [mdio-bus:07] driver [Atheros 8031 ethernet]
[ 3.976479] mt7530 mdio-bus:1f: configuring for fixed/rgmii link mode
[ 3.994051] DSA: tree 0 setup
[ 4.000412] mt7530 mdio-bus:1f: Link is Up - 1Gbps/Full - flow control off
[ 4.001465] UBI: auto-attach mtd5
[ 4.020764] ubi0: attaching mtd5
[ 5.358573] ubi0 error: ubi_attach: bad image sequence number 1717396771 in PEB 1048, expected 1051561099
[ 5.377643] Erase counter header dump:
[ 5.385097] magic 0x55424923
[ 5.392554] version 1
[ 5.398455] ec 0
[ 5.404352] vid_hdr_offset 2048
[ 5.410778] data_offset 4096
[ 5.417194] image_seq 1717396771
[ 5.424651] hdr_crc 0x41f68dff
[ 5.432107] erase counter header hexdump:
[ 5.440521] ubi0 error: ubi_attach_mtd_dev: failed to attach mtd5, error -22
[ 5.454595] UBI error: cannot attach mtd5
[ 5.462601] hctosys: unable to open rtc device (rtc0)
[ 5.473495] /dev/root: Can't open blockdev
[ 5.481701] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6
[ 5.496596] Please append a correct "root=" boot option; here are the available partitions:
[ 5.513231] 1f00 512 mtdblock0
[ 5.513235] (driver?)
[ 5.526248] 1f01 384 mtdblock1
[ 5.526251] (driver?)
[ 5.539271] 1f02 384 mtdblock2
[ 5.539274] (driver?)
[ 5.552283] 1f03 3072 mtdblock3
[ 5.552286] (driver?)
[ 5.565294] 1f04 3072 mtdblock4
[ 5.565298] (driver?)
[ 5.578321] 1f05 253696 mtdblock5
[ 5.578324] (driver?)
[ 5.591333] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[ 5.607798] Rebooting in 1 seconds..
I’ve observed a few different errors on 19.07.3:
[ 3.452384] UBI: auto-attach mtd5
[ 3.459042] ubi0: attaching mtd5
[ 5.063106] mtk_soc_eth 1e100000.ethernet eth0: port 1 link up
[ 5.731856] ubi0: scanning is finished
[ 5.753342] ubi0 error: 0x802f7820: bad attaching information, error 1
[ 5.766336] Volume attaching information dump:
[ 5.775176] vol_id 0
[ 5.781076] highest_lnum 526
[ 5.787307] leb_count 15
[ 5.793384] compat 0
[ 5.799284] vol_type 3
[ 5.805170] used_ebs 0
[ 5.811068] last_data_size 0
[ 5.816954] data_pad 0
[ 5.818148] mtk_soc_eth 1e100000.ethernet eth0: port 1 link down
[ 5.822855] Volume information dump:
[ 5.841894] vol_id 0
[ 5.847953] reserved_pebs 14
[ 5.854197] alignment 1
[ 5.860273] data_pad 0
[ 5.866332] vol_type 3
[ 5.872403] name_len 6
[ 5.878461] usable_leb_size 126976
[ 5.885396] used_ebs 14
[ 5.891642] used_bytes 1777664
[ 5.898752] last_eb_bytes 126976
[ 5.905674] corrupted 0
[ 5.911746] upd_marker 0
[ 5.917805] name rootfs
[ 5.925375] ubi0 error: 0x802fb1ec: failed to attach mtd5, error -22
[ 5.938048] UBI error: cannot attach mtd5
[ 3.443331] UBI: auto-attach mtd5
[ 3.450022] ubi0: attaching mtd5
[ 4.654666] ubi0 error: 0x80307340: bad image sequence number 1717396771 in PEB 1048, expected 1051561099
[ 4.673719] Erase counter header dump:
[ 4.681180] magic 0x55424923
[ 4.688623] version 1
[ 4.694526] ec 0
[ 4.700432] vid_hdr_offset 2048
[ 4.706837] data_offset 4096
[ 4.713259] image_seq 1717396771
[ 4.720720] hdr_crc 0x41f68dff
[ 4.728160] erase counter header hexdump:
[ 4.736480] ubi0 error: 0x802fb1ec: failed to attach mtd5, error -22
[ 4.749165] UBI error: cannot attach mtd5
|
|
28.07.2020 | 3253 | Base system | Bug Report | Very Low | Critical | Linksys WRT3200 ipv4 connection speed problems | openwrt-19.07 | Unconfirmed |
Task Description
I’m using Linksys wrt3200 as router behind cable modem with a dslite configuration and Devolo 1200+ DinRail connected to one of the LAN ports.
Previuos configuration was provider cable modem connected to Devolo and it was working fine (up to 50-100 mbit up and download to all DLAN devices.
After swiching to Linksys and OpenWRT I noticed that download speed for IPv4 dropped to 2-3 MBit for all devices. Upload and IPv6 work fine.
Thought it was dslite problem but provider router works fine and if I connect to Linksys directly via WLAN the download speed is as expected...
Repatched with Linksys stock firmware without changing anything else stable up and download speeds in expected range for ip4/ip6.
Patched openwrt back - ipv4 download drop to 2Mbit, back to stock back to normal speed...
Assume it’s potentially an MTU setting for LAN interface but all values I tried did not change much...
Would appreciate any help. Would be pity to fall back to stock but if it’s the only option...
|
|
02.08.2020 | 3264 | Base system | Bug Report | Very Low | Critical | R7800 router crashes when Macbook Air joins the network | Trunk | Unconfirmed |
Task Description
Supply the following if possible: - Device problem occurs on: Netgear R7800 Router, Macbook Air 11” Mid-2013, Macbook Air 13” 2017 - Software versions of OpenWrt/LEDE release: LuCI branch git-20.201.65700-7edd635 - Steps to reproduce: I join the device to the network with either ethernet or wifi and the router would shortly crash. I simply reboot the router and connect the macbook via ethernet or wifi after the router is up. I would then run a speedtest (it’s not related to any particular activity, but I just use speedtest.net as a control) - Attempts at trying to remedy issue: I tried disabling IPv6 on the router and macbooks. I signed out of icloud. I updated Macbooks to MacOS Catalina. I tried flashing router to latest stable release 19.07.3. The network only dies when these Macbook Airs connect to the network, all other devices don’t have any issues. Prior to this router, I had a Netgear AC1900 (R7000) running DD-WRT which never had this issue.
External logs captured before crash: 8/2/2020 14:14 Alert 192.168.1.1 [ 189.332615] 8←– cut here — 8/2/2020 14:14 Alert 192.168.1.1 [ 189.332636] Unable to handle kernel NULL pointer dereference at virtual address 0000000c 8/2/2020 14:14 Alert 192.168.1.1 [ 189.334560] pgd = eb7a8104 8/2/2020 14:14 Alert 192.168.1.1 [ 189.342856] [0000000c] *pgd=00000000 8/2/2020 14:14 Emergency 192.168.1.1 [ 189.345391] Internal error: Oops: 17 [#1] SMP ARM 8/2/2020 14:14 Warning 192.168.1.1 [ 189.349049] Modules linked in: ksmbd ath9k ath9k_common pppoe ppp_async ath9k_hw ath10k_pci ath10k_core ath qmi_wwan pppox ppp_generic mac80211 iptable_nat ipt_REJECT cfg80211 xt_time xt_tcpudp xt_tcpmss xt_statistic xt_state xt_recent xt_policy xt_nat xt_multiport xt_mark xt_mac xt_limit xt_length xt_hl xt_helper xt_geoip xt_esp xt_ecn xt_dscp xt_conntrack xt_connmark xt_connlimit xt_connbytes xt_comment xt_TCPMSS xt_REDIRECT xt_MASQUERADE xt_LOG xt_HL xt_FLOWOFFLOAD xt_DSCP xt_CT xt_CLASSIFY wireguard usbnet ums_usbat ums_sddr55 ums_sddr09 ums_karma ums_jumpshot ums_isd200 ums_freecom ums_datafab ums_cypress ums_alauda slhc sch_cake nf_reject_ipv4 nf_nat nf_log_ipv4 nf_flow_table_hw nf_flow_table nf_conntrack_rtcache nf_conntrack_netlink nf_conncount iptable_raw iptable_mangle iptable_filter ipt_ah ipt_ECN ip_tables crc_ccitt compat cdc_wdm fuse act_connmark nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 sch_tbf sch_ingress sch_htb sch_hfsc em_u32 cls_u32 cls_tcindex cls_route cls_matchall 8/2/2020 14:14 Warning 192.168.1.1 [ 189.349149] cls_fw cls_flow cls_basic act_skbedit act_mirred ledtrig_usbport ledtrig_heartbeat xt_set ip_set_list_set ip_set_hash_netportnet ip_set_hash_netport ip_set_hash_netnet ip_set_hash_netiface ip_set_hash_net ip_set_hash_mac ip_set_hash_ipportnet ip_set_hash_ipportip ip_set_hash_ipport ip_set_hash_ipmark ip_set_hash_ip ip_set_bitmap_port ip_set_bitmap_ipmac ip_set_bitmap_ip ip_set nfnetlink nf_log_ipv6 nf_log_common ip6table_mangle ip6table_filter ip6_tables ip6t_REJECT x_tables nf_reject_ipv6 ip6_gre ip_gre gre ifb ip6_udp_tunnel udp_tunnel sit ipcomp6 xfrm6_tunnel esp6 ah6 xfrm4_tunnel ipcomp esp4 ah4 ip6_tunnel tunnel6 tunnel4 ip_tunnel tun xfrm_user xfrm_ipcomp af_key xfrm_algo vfat fat autofs4 nls_utf8 nls_iso8859_1 nls_cp437 rfkill sha512_generic sha1_generic seqiv md5 md4 ghash_generic gf128mul gcm echainiv ecb des_generic libdes ctr cmac ccm cbc authenc arc4 uas usb_storage leds_gpio xhci_plat_hcd xhci_pci xhci_hcd dwc3 dwc3_qcom ohci_platform ohci_hcd phy_qcom_dwc3 ahci 8/2/2020 14:14 Warning 192.168.1.1 [ 189.418843] fsl_mph_dr_of ehci_platform ehci_fsl sd_mod ahci_platform libahci_platform libahci libata scsi_mod ehci_hcd gpio_button_hotplug f2fs ext4 mbcache jbd2 exfat(C) crc32c_generic crc32_generic 8/2/2020 14:14 Warning 192.168.1.1 [ 189.528411] CPU: 0 PID: 5 Comm: kworker/0:0 Tainted: G C 5.4.52 #0 8/2/2020 14:14 Warning 192.168.1.1 [ 189.546362] Hardware name: Generic DT based system 8/2/2020 14:14 Warning 192.168.1.1 [ 189.553873] Workqueue: ksmbd-io handle_ksmbd_work [ksmbd] 8/2/2020 14:14 Warning 192.168.1.1 [ 189.558534] PC is at ksmbd_free_user+0xc/0×38 [ksmbd] 8/2/2020 14:14 Warning 192.168.1.1 [ 189.564001] LR is at smb_session_disconnect+0×40/0xa4 [ksmbd] 8/2/2020 14:14 Warning 192.168.1.1 [ 189.569016] pc : [<bf9242e0>] lr : [<bf9402ac>] psr: 60000013 8/2/2020 14:14 Warning 192.168.1.1 [ 189.574745] sp : dd459ee0 ip : d83da240 fp : bf94f004 8/2/2020 14:14 Warning 192.168.1.1 [ 189.580820] r10: bf958234 r9 : 000001d0 r8 : bf957b58 8/2/2020 14:14 Warning 192.168.1.1 [ 189.586030] r7 : d83da200 r6 : 00000000 r5 : d69b2a00 r4 : 00000000 8/2/2020 14:14 Warning 192.168.1.1 [ 189.591238] r3 : d83da200 r2 : 00000003 r1 : 00000001 r0 : 00000000 8/2/2020 14:14 Warning 192.168.1.1 [ 189.597838] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none 8/2/2020 14:14 Warning 192.168.1.1 [ 189.604348] Control: 10c5787d Table: 5eb7806a DAC: 00000051 8/2/2020 14:14 Emergency 192.168.1.1 [ 189.611551] Process kworker/0:0 (pid: 5 8/2/2020 14:14 Emergency 192.168.1.1 [ 189.617280] Stack: (0xdd459ee0 to 0xdd45a000) 8/2/2020 14:14 Emergency 192.168.1.1 [ 189.623367] 9ee0: dcbcc480 bf9402ac d83da200 dcbcc480 dcbcc4dc 00000074 bf957b58 bf9290e4 8/2/2020 14:14 Emergency 192.168.1.1 [ 189.627799] 9f00: dcddb704 dcde6400 c0c221cc dcbcc4dc dd40f500 dda09840 ff7e6500 00000000 8/2/2020 14:14 Emergency 192.168.1.1 [ 189.635957] 9f20: 00000000 00000000 dd458000 c033a684 00000008 dda09858 dd40f500 dd40f514 8/2/2020 14:14 Emergency 192.168.1.1 [ 189.644116] 9f40: dda09840 00000008 dda09858 c0c03d00 dda09840 c033a948 c0c0c35c c0c0c318 8/2/2020 14:14 Emergency 192.168.1.1 [ 189.652276] 9f60: dd41951c dd419500 dd419280 dd458000 dd41951c dd43bea4 dd40f500 c033a8f4 8/2/2020 14:14 Emergency 192.168.1.1 [ 189.660436] 9f80: 00000000 c0340724 00000000 dd419280 c0340608 00000000 00000000 00000000 8/2/2020 14:14 Emergency 192.168.1.1 [ 189.668596] 9fa0: 00000000 00000000 00000000 c03010e8 00000000 00000000 00000000 00000000 8/2/2020 14:14 Emergency 192.168.1.1 [ 189.676755] 9fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 8/2/2020 14:14 Emergency 192.168.1.1 [ 189.684915] 9fe0: 00000000 00000000 00000000 00000000 00000013 00000000 00000000 00000000 8/2/2020 14:14 Warning 192.168.1.1 [ 189.693179] [<bf9242e0>] (ksmbd_free_user [ksmbd]) from [<bf9402ac>] (smb_session_disconnect+0×40/0xa4 [ksmbd]) 8/2/2020 14:14 Warning 192.168.1.1 [ 189.701271] [<bf9402ac>] (smb_session_disconnect [ksmbd]) from [<bf9290e4>] (handle_ksmbd_work+0x18c/0×500 [ksmbd]) 8/2/2020 14:14 Warning 192.168.1.1 [ 189.711150] [<bf9290e4>] (handle_ksmbd_work [ksmbd]) from [<c033a684>] (process_one_work+0x1f8/0×468) 8/2/2020 14:14 Warning 192.168.1.1 [ 189.721543] [<c033a684>] (process_one_work) from [<c033a948>] (worker_thread+0×54/0×588) 8/2/2020 14:14 Warning 192.168.1.1 [ 189.730919] [<c033a948>] (worker_thread) from [<c0340724>] (kthread+0x11c/0×148) 8/2/2020 14:14 Warning 192.168.1.1 [ 189.739077] [<c0340724>] (kthread) from [<c03010e8>] (ret_from_fork+0×14/0x2c) 8/2/2020 14:14 Warning 192.168.1.1 [ 189.746448] Exception stack(0xdd459fb0 to 0xdd459ff8) 8/2/2020 14:14 Warning 192.168.1.1 [ 189.753483] 9fa0: 00000000 00000000 00000000 00000000 8/2/2020 14:14 Warning 192.168.1.1 [ 189.758613] 9fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 8/2/2020 14:14 Warning 192.168.1.1 [ 189.766769] 9fe0: 00000000 00000000 00000000 00000000 00000013 00000000 8/2/2020 14:14 Emergency 192.168.1.1 [ 189.774929] Code: eaffffd1 e52d4008 e1a04000 e58de004 (e590000c) 8/2/2020 14:14 Warning 192.168.1.1 [ 189.781453] —[ end trace 469d54bcbf49ae73 ]—
|
|
09.08.2020 | 3280 | Base system | Bug Report | Very Low | Critical | Wan interface and sometimes lan interfaces randomly go ... | Trunk | Unconfirmed |
Task Description
- Versions where bug is present: OpenWRT snapshots, tested with r13938 and r18039.
- Affected device: D-Link DIR-878 and likely others from its family.
- What does it do and shouldn’t do: the ethernet interfaces randomly get switched on/off, dropping the link and resetting the connection. Troubleshooting has already been thoroughly conducted to rule out other causes, see below. This is critical severity because makes OpenWRT unusable in these devices.
- Steps to reproduce: – flash the snapshot image on a D-Link DIR-878; – configure the WAN (tested with PPPoE and DHCP protocols) and LAN interfaces (tested with Static and DHCP protocols) - using all interfaces will increase the likelihood that at least one of them will present the behaviour; – wait an indefinite but reasonable (< 2h for all instances so far) amount of time; – the interface will randomly be put down and then up a couple seconds later, and it will be randomly looping up/down states at random amounts of time.
- Troubleshooting already conducted: full and detailed troubleshooting history is present at this forum thread. Please let me know if I can provide further information.
- Additional info: some people are having WiFi issues with MT7621 family devices that might be related to this one if they share a common cause, such as a possible race condition in the drivers;
|
|
21.08.2020 | 3298 | Base system | Bug Report | Very Low | Critical | Edimax 3G-6200n z OpenWrt 19.07.2 lost settings after r... | openwrt-19.07 | Unconfirmed |
Task Description
Edimax 3G-6200n OpenWrt 19.07.2, r10947-65030d81f3
Steps: 1. Download the latest version OpenWrt 19.07.2 to Edimax 3G-6200n. 2. Set e.g. the password to the router and/or turn on the WiFi. 3. Reboot the router with the reboot option in OpenWrt. 4. The router has no settings previously saved - the status is as right after installing fresh OpenWRT - no password, no WiFi enabled, default settings.
Problem with JFFS.
root@OpenWrt:~# mount
/dev/root on /rom type squashfs (ro,relatime)
proc on /proc type proc (rw,nosuid,nodev,noexec,noatime)
sysfs on /sys type sysfs (rw,nosuid,nodev,noexec,noatime)
tmpfs on /tmp type tmpfs (rw,nosuid,nodev,noatime)
tmpfs on /tmp/root type tmpfs (rw,noatime,mode=755)
overlayfs:/tmp/root on / type overlay (rw,noatime,lowerdir=/,upperdir=/tmp/root/upper,workdir=/tmp/root/work)
tmpfs on /dev type tmpfs (rw,nosuid,relatime,size=512k,mode=755)
devpts on /dev/pts type devpts (rw,nosuid,noexec,relatime,mode=600,ptmxmode=000)
debugfs on /sys/kernel/debug type debugfs (rw,noatime)
root@OpenWrt:~# df -h
Filesystem Size Used Available Use% Mounted on
/dev/root 3.0M 3.0M 0 100% /rom
tmpfs 13.8M 284.0K 13.5M 2% /tmp
tmpfs 13.8M 60.0K 13.7M 0% /tmp/root
overlayfs:/tmp/root 13.8M 60.0K 13.7M 0% /
tmpfs 512.0K 0 512.0K 0% /dev
root@OpenWrt:~# free
total used free shared buff/cache available
Mem: 28276 14008 5224 344 9044 11872
Swap: 0 0 0
#here I added the password and turned on the WiFi network - the free RAM decreased
root@OpenWrt:~# free
total used free shared buff/cache available
Mem: 28276 15632 3496 368 9148 10236
Swap: 0 0 0
root@OpenWrt:~#
|
|
21.08.2020 | 3299 | Base system | Bug Report | Very Low | Critical | busybox: Alternatives gets overwrited when busybox upda... | Trunk | Unconfirmed |
Task Description
This is device independent and I think it affects all versions but I have seen this over 19.07. If you have binary programs that conflicts with busybox ones, opkg sets them to be used instead when they are installed.
I discovered this because mwan3 got broke and investigating the error it dropped the problems seems to be that the ip binary from busybox doesn’t support some features mwan3 needs. I could find that I had ip installed as is a dependency of mwan3 so I just remembered that busybox was updated recently.
Just by reinstalling ip the issue was solved.
I don’t know how this could be managed, perhaps just when a package that has alternatives is installed update them and when the package is being upgraded ignore updating the alternatives.
I set this critical just because it could be very difficult to see where the problem is for many people (I surprised myself how it could take so many time to advert the real issue when I found it, it’s simple, but if you don’t notice busybox upgrading could be cumbersome to see), and, this could break things, like for example mwan3 or any other program that rely using alternative binaries and not the busybox ones. Of course fell free to set the severity you think could be more accurate.
|
|
17.09.2020 | 3345 | Base system | Bug Report | Very Low | Critical | Wifi off | Trunk | Unconfirmed |
Task Description
Supply the following if possible: - Device problem occurs on TP-Link TL-WR842N v5. - OpenWrt/LEDE 19.07.04 with last updating. - Just use wifi on the device. It have random wifi off about 1 min. Log: https://pastebin.com/c64H5kCR
|
|
28.09.2020 | 3365 | Base system | Bug Report | Very Low | Critical | access USB storage in LEDE for Talon AD7200 | Trunk | Unconfirmed |
Task Description
Anybody have an ideal to access USB storage at Talon AD72000 with nexmon firmware? lede-ad7200?
Several ways I have tried:
1. search for path like `/mnt/dev` `/dev/`, I can see my usb flash disk led blinking and there show up the device after I insert the disk, but I can NOT cd into the disk
2. install other tool via `opkg`, especially Quick Start for Adding a USB drive, however, the whole OS will crash down when install `kmod-usb-storage` at step 3 and I have to start all over.
Let me know if any solution
Best.
|
|
09.10.2020 | 3372 | Base system | Bug Report | Very Low | Critical | After flashing 19.07.4 on Kingston MLWG2, no network ar... | openwrt-19.07 | Unconfirmed |
Task Description
Just flashed 19.07.4 on Kingston MLWG2.
Followed online procedure found (copy image to SD card, touch special file, login via telnet on stock firmware, write image, reboot device) to flash OpenWRT.
After flash, device “seems” stuck dead (all leds are on, wired network irresponsive, no WiFi AP detected).
I have opened the device, soldered the serial console pins and accessere via serial console.
Device is actually booting perfectly, but both wired and wifi are not accessible.
1. I have WiFi enabled by setting “disabled = 0” in /etc/config/wireless to OpenWrt AP
2. I have Wired enabled by adding “option iface “eth0”” to the “lan” interface in /etc/config/network
3. Device now works great
Without these two changes, the device is as good as dead.
This is a peculiar device: only 1 ethernet port and 2.4Ghz Wifi. My guess something is wrong in the vlan/bridge/switch settings?
I hope a fix can be commited somehow so that future users do not end up with a dead-like device.
|
|
23.10.2020 | 3402 | Base system | Bug Report | Very Low | Critical | RUT955: Seriously broken | Trunk | Unconfirmed |
Task Description
RS485 and RS232 (DB9) unusable on my recent RUT955, batch 84. I want to use RS485 (in worst case, RS232) for modbus comms.
However, my custom built image basically works, incl. mqtt, mwan3, LTE (EC25) etc. The firmware from TELTONIKA runs without problems. For strange boot log, pls refere to https://forum.openwrt.org/t/teltonika-rut955-tainted-kernel-ath1/77335/2
|
|
29.12.2020 | 3544 | Base system | Bug Report | Very Low | Critical | 5GHz band of several ath10k devices are completely unus... | Trunk | Unconfirmed |
Task Description
- Device: Custom router board with mini PCIE slots - Software version: OpenWrt SNAPSHOT r0-7e4585e - Steps to reproduce: * Git clone https://github.com/openwrt/openwrt then build with default configuration + enable ath10k & fw. * Install an ath10k card (tested: QCA9880, QCA6174) on router board, and flash image to device. * Run `iw list` and every 5GHz band is disabled.
Changing country code via LuCI and `iw reg set` won’t help.
Using ath10k-ct won’t help as well.
ath9k is not affected.
Logs are in attachments.
|
|
14.10.2016 | 227 | Base system | Bug Report | Medium | High | VLAN support mismatch between preinit and default netwo... | Trunk | Researching |
Task Description
PPPoE is broken on WRT1900ACS
Upgraded from Lede r578 to latest Lede r1814 and PPPOE doesn’t work anymore altough the pppd version and PPPoE version are the same: - Linksys WRT1900ACS - LEDE reboot r1814
pppd debug log:
Plugin rp-pppoe.so loaded. RP-PPPoE plugin version 3.8p compiled against pppd 2.4.7 Send PPPOE Discovery V1T1 PADI session 0×0 length 4 dst ff:ff:ff:ff:ff:ff src c2:56:27:ca:d7:d4 [service-name] Send PPPOE Discovery V1T1 PADI session 0×0 length 4 dst ff:ff:ff:ff:ff:ff src c2:56:27:ca:d7:d4 [service-name] Send PPPOE Discovery V1T1 PADI session 0×0 length 4 dst ff:ff:ff:ff:ff:ff src c2:56:27:ca:d7:d4 [service-name] Timeout waiting for PADO packets Unable to complete PPPoE Discovery Plugin rp-pppoe.so loaded. RP-PPPoE plugin version 3.8p compiled against pppd 2.4.7 Send PPPOE Discovery V1T1 PADI session 0×0 length 4 dst ff:ff:ff:ff:ff:ff src c2:56:27:ca:d7:d4 [service-name] Send PPPOE Discovery V1T1 PADI session 0×0 length 4 dst ff:ff:ff:ff:ff:ff src c2:56:27:ca:d7:d4 [service-name] Send PPPOE Discovery V1T1 PADI session 0×0 length 4 dst ff:ff:ff:ff:ff:ff src c2:56:27:ca:d7:d4 [service-name]
While on the same hardware running LEDE r578, the PPPoE module works as expected:
Plugin rp-pppoe.so loaded. RP-PPPoE plugin version 3.8p compiled against pppd 2.4.7 Send PPPOE Discovery V1T1 PADI session 0×0 length 4 dst ff:ff:ff:ff:ff:ff src c2:56:27:ca:d7:d4 [service-name] Recv PPPOE Discovery V1T1 PADO session 0×0 length 40 dst c2:56:27:ca:d7:d4 src a0:f3:e4:34:d8:21 [service-name] [AC-name acc-aln1.hac] [AC-cookie 75 58 37 a5 ba 3c e4 a5 2a 61 bb 23 92 5c 1b dc] Send PPPOE Discovery V1T1 PADR session 0×0 length 24 dst a0:f3:e4:34:d8:21 src c2:56:27:ca:d7:d4 [service-name] [AC-cookie 75 58 37 a5 ba 3c e4 a5 2a 61 bb 23 92 5c 1b dc] Recv PPPOE Discovery V1T1 PADS session 0x30b length 4 dst c2:56:27:ca:d7:d4 src a0:f3:e4:34:d8:21 [service-name] PADS: Service-Name: ‘’ PPP session is 779 Connected to a0:f3:e4:34:d8:21 via interface eth0 using channel 2 Using interface pppoe-wan Connect: pppoe-wan ←→ eth0 sent [LCP ConfReq id=0×1 <mru 1492> <magic 0xc6952556>] rcvd [LCP ConfReq id=0×66 <mru 1492> <auth chap MD5> <magic 0x4cc73648>] sent [LCP ConfAck id=0×66 <mru 1492> <auth chap MD5> <magic 0x4cc73648>] rcvd [LCP ConfAck id=0×1 <mru 1492> <magic 0xc6952556>] sent [LCP EchoReq id=0×0 magic=0xc6952556] rcvd [CHAP Challenge id=0×1 <7131a44524d1de8f1cd1061cac6d8c071d8bfe7351bc4ea7bd08f56684428475f229ba177a192696ebab32>, name = “acc-aln1.hac”] sent [CHAP Response id=0×1 <4bb1a418b298790b128ad4d7ef3109ad>, name = “bthomehub@btbroadband.com”] rcvd [LCP EchoRep id=0×0 magic=0x4cc73648] rcvd [CHAP Success id=0×1 “CHAP authentication success”] CHAP authentication succeeded: CHAP authentication success CHAP authentication succeeded peer from calling number A0:F3:E4:34:D8:21 authorized sent [IPCP ConfReq id=0×1 <addr 0.0.0.0> <ms-dns1 0.0.0.0> <ms-dns2 0.0.0.0>] sent [IPV6CP ConfReq id=0×1 <addr fe80::c595:37d1:3987:1929>] rcvd [IPV6CP ConfReq id=0x7b <addr fe80::0221:05ff:feb4:8824>] sent [IPV6CP ConfAck id=0x7b <addr fe80::0221:05ff:feb4:8824>] rcvd [IPCP ConfReq id=0×38 <addr 172.16.12.12>] sent [IPCP ConfAck id=0×38 <addr 172.16.12.12>] rcvd [IPCP ConfNak id=0×1 <addr 81.146.2.155> <ms-dns1 81.139.57.100> <ms-dns2 81.139.56.100>] sent [IPCP ConfReq id=0×2 <addr 81.146.2.155> <ms-dns1 81.139.57.100> <ms-dns2 81.139.56.100>] rcvd [IPV6CP ConfAck id=0×1 <addr fe80::c595:37d1:3987:1929>] local LL address fe80::c595:37d1:3987:1929 remote LL address fe80::0221:05ff:feb4:8824 Script /lib/netifd/ppp-up started (pid 2646) rcvd [IPCP ConfAck id=0×2 <addr 81.146.2.155> <ms-dns1 81.139.57.100> <ms-dns2 81.139.56.100>] local IP address 81.146.2.155 remote IP address 172.16.12.12 primary DNS address 81.139.57.100 secondary DNS address 81.139.56.100 ppp.log secondary DNS address 81.139.56.100 Script /lib/netifd/ppp-up started (pid 2653) Script /lib/netifd/ppp-up finished (pid 2646), status = 0×9 Script /lib/netifd/ppp-up finished (pid 2653), status = 0×9
|
|
27.10.2016 | 253 | Base system | Bug Report | Very Low | High | Multicast over wireless ceases to work properly after a... | All | New |
Task Description
I am having a problem on a UBNT UAP-LR where, if many clients stay connected the router for a long time, multicast packets will stop being reliably sent to the wireless clients. I can reproduce this with LEDE r1953, but it goes back at least as far as OpenWRT 15.05.1 with kernel 3.18. I can not, however, reproduce it on another network with the same WAP but with only one or two wireless clients.
This originally manifested as IPv6 ceasing to work since the (multicasted) RA packets were not reaching the wireless clients. I used tcpdump on the WAP and determined that the RAs were arriving through the wired interface and leaving through the wireless interface as they should, but tcpdump on the client indicates that a vast majority of the RAs are never received. (Please note that the IPv6 issue is not reproducible with the router running OpenWRT/LEDE and odhcpd, since odhcpd unicasts RAs sent as a response to an RS instead of multicasting them, while it is reproducible when the router is running radvd, for example as pfSense does.)
|
|
21.11.2016 | 296 | Base system | Bug Report | Very Low | High | Ubiquiti Bullet M 10/100 ethernet interface comes up as... | Trunk | Unconfirmed |
Task Description
For the last month or so, and persisting in r2248, when a Ubiquiti Bullet M is booted through typical Ubiquiti 10/100 passive PoE injector, the interface appears to come up in gigabit mode (see timestamp 18.990274 below), despite being only a 10/100 Mbps interface. Restarting /etc/init.d/network fixes it. I am running batman-adv over the ethernet interface, which may be involved. I will check if it happens when batman-adv is not used on the interface and report in a followup comment.
The dmesg look like this:
[ 0.000000] Linux version 4.4.32 (openwrt@hawg) (gcc version 5.4.0 (LEDE GCC 5.4.0 r1439) ) #0 Mon Nov 21 07:14:51 2016
[ 0.000000] MyLoader: sysp=00030800, boardp=088201a0, parts=fdeffeff
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
[ 0.000000] SoC: Atheros AR7240 rev 2
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] No valid device tree found, continuing without
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000001ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000001ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000001ffffff]
[ 0.000000] On node 0 totalpages: 8192
[ 0.000000] free_area_init_node: node 0, pgdat 80412320, node_mem_map 81000000
[ 0.000000] Normal zone: 64 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 8192 pages, LIFO batch:0
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
[ 0.000000] Kernel command line: board=UBNT-BM mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,7552k(firmware),256k(cfg)ro,64k(EEPROM)ro console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 27616K/32768K available (2990K kernel code, 174K rwdata, 756K rodata, 296K init, 198K bss, 5152K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Clocks: CPU:390.000MHz, DDR:390.000MHz, AHB:195.000MHz, Ref:40.000MHz
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9801335621 ns
[ 0.000013] sched_clock: 32 bits at 195MHz, resolution 5ns, wraps every 11012737021ns
[ 0.007858] Calibrating delay loop... 259.27 BogoMIPS (lpj=1296384)
[ 0.080537] pid_max: default: 32768 minimum: 301
[ 0.085319] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.091915] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.102739] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.113516] NET: Registered protocol family 16
[ 0.120053] MIPS: machine is Ubiquiti Bullet M
[ 0.126714] registering PCI controller with io_map_base unset
[ 0.357171] PCI host bridge to bus 0000:00
[ 0.361273] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
[ 0.368174] pci_bus 0000:00: root bus resource [io 0x0000]
[ 0.373719] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 0.380486] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.388422] pci 0000:00:00.0: [168c:002a] type 00 class 0x028000
[ 0.388466] pci 0000:00:00.0: fixup device configuration
[ 0.395018] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x0000ffff 64bit]
[ 0.395154] pci 0000:00:00.0: supports D1
[ 0.395179] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 0.395521] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 0.395573] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1000ffff 64bit]
[ 0.402864] pci 0000:00:00.0: using irq 40 for pin 1
[ 0.408959] clocksource: Switched to clocksource MIPS
[ 0.415845] NET: Registered protocol family 2
[ 0.421435] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.428393] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.434796] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.441291] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.447126] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.453786] NET: Registered protocol family 1
[ 0.458221] PCI: CLS 0 bytes, default 32
[ 0.464223] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.470512] Crashlog allocated RAM at address 0x1f00000
[ 0.495166] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.501050] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.514332] io scheduler noop registered
[ 0.518252] io scheduler deadline registered (default)
[ 0.523724] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.530709] console [ttyS0] disabled
[ 0.554342] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 12187500) is a 16550A
[ 0.563020] console [ttyS0] enabled
[ 0.570030] bootconsole [early0] disabled
[ 0.582486] m25p80 spi0.0: found mx25l6405d, expected m25p80
[ 0.588201] m25p80 spi0.0: mx25l6405d (8192 Kbytes)
[ 0.593207] 5 cmdlinepart partitions found on MTD device spi0.0
[ 0.599160] Creating 5 MTD partitions on "spi0.0":
[ 0.603978] 0x000000000000-0x000000040000 : "u-boot"
[ 0.611975] 0x000000040000-0x000000050000 : "u-boot-env"
[ 0.619659] 0x000000050000-0x0000007b0000 : "firmware"
[ 0.638850] 2 uimage-fw partitions found on MTD device firmware
[ 0.644866] 0x000000050000-0x0000001a0000 : "kernel"
[ 0.651748] 0x0000001a0000-0x0000007b0000 : "rootfs"
[ 0.658927] mtd: device 4 (rootfs) set to be root filesystem
[ 0.664753] 1 squashfs-split partitions found on MTD device rootfs
[ 0.671002] 0x000000550000-0x0000007b0000 : "rootfs_data"
[ 0.678725] 0x0000007b0000-0x0000007f0000 : "cfg"
[ 0.685799] 0x0000007f0000-0x000000800000 : "EEPROM"
[ 0.713743] libphy: ag71xx_mdio: probed
[ 1.302694] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:04 [uid=004dd041, driver=Generic PHY]
[ 1.312905] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[ 1.322158] NET: Registered protocol family 10
[ 1.332118] NET: Registered protocol family 17
[ 1.336691] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 1.349583] 8021q: 802.1Q VLAN Support v1.8
[ 1.362372] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[ 1.372025] Freeing unused kernel memory: 296K (80436000 - 80480000)
[ 2.887723] init: Console is alive
[ 2.891524] init: - watchdog -
[ 4.278153] usbcore: registered new interface driver usbfs
[ 4.283867] usbcore: registered new interface driver hub
[ 4.289377] usbcore: registered new device driver usb
[ 4.301662] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 4.310384] ehci-platform: EHCI generic platform driver
[ 4.319460] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 4.327414] ohci-platform: OHCI generic platform driver
[ 4.336259] init: - preinit -
[ 5.148878] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 5.181862] random: procd: uninitialized urandom read (4 bytes read, 8 bits of entropy available)
[ 7.440590] eth0: link up (100Mbps/Full duplex)
[ 7.445184] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 8.484066] jffs2: notice: (361) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 8.501955] mount_root: switching to jffs2 overlay
[ 8.517794] urandom-seed: Seeding with /etc/urandom.seed
[ 8.794632] eth0: link down
[ 8.814035] procd: - early -
[ 8.817063] procd: - watchdog -
[ 9.492101] procd: - ubus -
[ 9.545805] random: ubusd: uninitialized urandom read (4 bytes read, 15 bits of entropy available)
[ 9.555498] random: ubusd: uninitialized urandom read (4 bytes read, 15 bits of entropy available)
[ 9.564637] random: ubusd: uninitialized urandom read (4 bytes read, 15 bits of entropy available)
[ 9.574254] random: ubusd: uninitialized urandom read (4 bytes read, 15 bits of entropy available)
[ 9.583375] random: ubusd: uninitialized urandom read (4 bytes read, 15 bits of entropy available)
[ 9.593373] random: ubusd: uninitialized urandom read (4 bytes read, 16 bits of entropy available)
[ 9.602738] random: ubusd: uninitialized urandom read (4 bytes read, 16 bits of entropy available)
[ 9.612394] procd: - init -
[ 10.066368] Loading modules backported from Linux version wt-2016-10-03-1-g6fcb1a6
[ 10.074041] Backport generated by backports.git backports-20160324-9-g0e38f5c
[ 10.125220] batman_adv: B.A.T.M.A.N. advanced 2016.4 (compatibility version 15) loaded
[ 10.213939] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[ 10.224958] ath: phy0: Ignoring endianness difference in EEPROM magic bytes.
[ 10.233630] ath: EEPROM regdomain: 0x0
[ 10.233647] ath: EEPROM indicates default country code should be used
[ 10.233661] ath: doing EEPROM country->regdmn map search
[ 10.233689] ath: country maps to regdmn code: 0x3a
[ 10.233705] ath: Country alpha2 being used: US
[ 10.233718] ath: Regpair used: 0x3a
[ 10.248634] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 10.257391] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xb0000000, irq=40
[ 11.870351] random: jshn: uninitialized urandom read (4 bytes read, 19 bits of entropy available)
[ 12.001559] random: ubusd: uninitialized urandom read (4 bytes read, 19 bits of entropy available)
[ 18.855427] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 18.875510] IPv6: ADDRCONF(NETDEV_UP): br-pub: link is not ready
[ 18.990274] eth0: link up (1000Mbps/Full duplex)
[ 18.994964] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 19.330349] batman_adv: bat0: Adding interface: eth0
[ 19.335365] batman_adv: bat0: The MTU of interface eth0 is too small (1500) to handle the transport of batman-adv packets. Packets going over this interface will be fragmented on layer2 which could impact the
performance. Setting the MTU to 1532 would solve the problem.
[ 19.359419] batman_adv: bat0: Interface activated: eth0
[ 19.367077] 8021q: adding VLAN 0 to HW filter on device bat0
[ 19.406417] device bat0 entered promiscuous mode
[ 19.411309] br-pub: port 1(bat0) entered forwarding state
[ 19.416772] br-pub: port 1(bat0) entered forwarding state
[ 19.422579] IPv6: ADDRCONF(NETDEV_CHANGE): br-pub: link becomes ready
[ 19.870508] batman_adv: bat0: bridge_loop_avoidance: Changing from: enabled to: disabled
[ 20.359133] batman_adv: bat0: No IGMP Querier present - multicast optimizations disabled
[ 20.367269] batman_adv: bat0: No MLD Querier present - multicast optimizations disabled
[ 21.412169] br-pub: port 1(bat0) entered forwarding state
[ 21.549966] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 21.563679] device wlan0 entered promiscuous mode
[ 21.591315] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 21.597879] br-pub: port 2(wlan0) entered forwarding state
[ 21.603541] br-pub: port 2(wlan0) entered forwarding state
[ 21.784924] IPv6: ADDRCONF(NETDEV_UP): mesh0: link is not ready
[ 21.912131] IPv6: ADDRCONF(NETDEV_CHANGE): mesh0: link becomes ready
[ 22.268273] batman_adv: bat0: Adding interface: mesh0
[ 22.273432] batman_adv: bat0: Interface activated: mesh0
[ 23.599046] br-pub: port 2(wlan0) entered forwarding state
[ 29.369162] batman_adv: bat0: IGMP Querier appeared
[ 29.374093] batman_adv: bat0: MLD Querier appeared
[ 34.068975] ------------[ cut here ]------------
[ 34.073700] WARNING: CPU: 0 PID: 0 at net/sched/sch_generic.c:306 dev_watchdog+0x1dc/0x260()
[ 34.082197] NETDEV WATCHDOG: eth0 (ag71xx): transmit queue 0 timed out
[ 34.088754] Modules linked in: ath9k ath9k_common mac80211 ath9k_hw ath batman_adv libcrc32c cfg80211 compat ohci_platform ohci_hcd ehci_platform ehci_hcd gpio_button_hotplug usbcore nls_base usb_common crc16
cryptomgr aead crypto_null crc32c_generic crypto_hash
[ 34.112252] CPU: 0 PID: 0 Comm: swapper Not tainted 4.4.32 #0
[ 34.118013] Stack : 803c8fc4 00000000 00000001 80420000 80413038 80412cc3 803aa67c 00000000
[ 34.118013] 8048379c 8041135c 00000200 00100000 0000000a 800a71a8 803afce8 80410000
[ 34.118013] 00000003 8041135c 803ae0f4 8040dc2c 0000000a 800a5124 00000006 00000000
[ 34.118013] 00000000 801f3100 00000000 00000000 00000000 00000000 00000000 00000000
[ 34.118013] 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 34.118013] ...
[ 34.153969] Call Trace:
[ 34.156440] [<80071af0>] show_stack+0x50/0x84
[ 34.160843] [<80081870>] warn_slowpath_common+0xa0/0xd0
[ 34.166096] [<800818cc>] warn_slowpath_fmt+0x2c/0x38
[ 34.171111] [<80290970>] dev_watchdog+0x1dc/0x260
[ 34.175854] [<800b0460>] call_timer_fn.isra.5+0x24/0x80
[ 34.181125] [<800b06e4>] run_timer_softirq+0x1b4/0x1fc
[ 34.186296] [<80083dec>] __do_softirq+0x250/0x298
[ 34.191059] [<8006a5d0>] plat_irq_dispatch+0xd4/0x10c
[ 34.196134] [<80060830>] ret_from_irq+0x0/0x4
[ 34.200526] [<80060a80>] __r4k_wait+0x20/0x40
[ 34.204906] [<800a2304>] cpu_startup_entry+0x9c/0xe8
[ 34.209934] [<80436bd4>] start_kernel+0x470/0x490
[ 34.214656]
[ 34.216159] ---[ end trace ef06a4b3ec78272a ]---
[ 34.220810] eth0: tx timeout
[ 37.565193] random: nonblocking pool is initialized
[ 44.068999] eth0: tx timeout
[ 54.069064] eth0: tx timeout
[ 64.068993] eth0: tx timeout
[ 74.069871] eth0: tx timeout
[ 82.660973] batman_adv: bat0: MLD Querier disappeared - multicast optimizations disabled
[ 84.070901] eth0: tx timeout
[ 92.701961] batman_adv: bat0: MLD Querier appeared
[ 94.071717] eth0: tx timeout
[ 104.072355] eth0: tx timeout
[ 114.072669] eth0: tx timeout
[...]
When I do an /etc/init.d/network restart, the interface recovers to normal function, and I get this in dmesg:
[ 1296.763793] br-pub: port 2(wlan0) entered disabled state
[ 1296.769232] br-pub: port 1(bat0) entered disabled state
[ 1296.808305] device bat0 left promiscuous mode
[ 1296.812986] br-pub: port 1(bat0) entered disabled state
[ 1296.862085] IPv6: ADDRCONF(NETDEV_UP): bat0: link is not ready
[ 1296.879239] device wlan0 left promiscuous mode
[ 1296.883945] br-pub: port 2(wlan0) entered disabled state
[ 1296.904196] batman_adv: bat0: Interface deactivated: mesh0
[ 1296.909752] batman_adv: bat0: Removing interface: mesh0
[ 1296.963462] batman_adv: bat0: Interface deactivated: eth0
[ 1296.993492] eth0: link down
[ 1296.998705] batman_adv: bat0: Removing interface: eth0
[ 1301.629484] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 1301.649941] IPv6: ADDRCONF(NETDEV_UP): br-pub: link is not ready
[ 1301.985100] eth0: link up (100Mbps/Full duplex)
[ 1301.989698] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 1302.191373] batman_adv: bat0: Adding interface: eth0
[ 1302.196453] batman_adv: bat0: The MTU of interface eth0 is too small (1500) to handle the transport of batman-adv packets. Packets going over this interface will be fragmented on layer2 which could impact the
performance. Setting the MTU to 1532 would solve the problem.
[ 1302.220488] batman_adv: bat0: Interface activated: eth0
[ 1302.228092] 8021q: adding VLAN 0 to HW filter on device bat0
[ 1302.275944] device bat0 entered promiscuous mode
[ 1302.280747] br-pub: port 1(bat0) entered forwarding state
[ 1302.286292] br-pub: port 1(bat0) entered forwarding state
[ 1302.292106] IPv6: ADDRCONF(NETDEV_CHANGE): br-pub: link becomes ready
[ 1302.590333] batman_adv: bat0: bridge_loop_avoidance: Changing from: enabled to: disabled
[ 1303.213417] batman_adv: bat0: No IGMP Querier present - multicast optimizations disabled
[ 1303.221556] batman_adv: bat0: No MLD Querier present - multicast optimizations disabled
[ 1304.283452] br-pub: port 1(bat0) entered forwarding state
[ 1304.672382] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 1304.782643] device wlan0 entered promiscuous mode
[ 1304.827845] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 1304.834479] br-pub: port 2(wlan0) entered forwarding state
[ 1304.840053] br-pub: port 2(wlan0) entered forwarding state
[ 1305.112607] IPv6: ADDRCONF(NETDEV_UP): mesh0: link is not ready
[ 1305.190600] IPv6: ADDRCONF(NETDEV_CHANGE): mesh0: link becomes ready
[ 1305.692918] batman_adv: bat0: Adding interface: mesh0
[ 1305.698080] batman_adv: bat0: Interface activated: mesh0
[ 1306.833410] br-pub: port 2(wlan0) entered forwarding state
[ 1312.303688] batman_adv: bat0: IGMP Querier appeared
[ 1312.308629] batman_adv: bat0: MLD Querier appeared
If I disconnect the other end of the ethernet cable so that there is no link peer, I do not see the problem (see below):
[ 0.000000] Linux version 4.4.32 (openwrt@hawg) (gcc version 5.4.0 (LEDE GCC 5.4.0 r1439) ) #0 Mon Nov 21 07:14:51 2016
[ 0.000000] MyLoader: sysp=00000000, boardp=00000000, parts=ffffffff
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
[ 0.000000] SoC: Atheros AR7240 rev 2
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] No valid device tree found, continuing without
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000001ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000001ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000001ffffff]
[ 0.000000] On node 0 totalpages: 8192
[ 0.000000] free_area_init_node: node 0, pgdat 80412320, node_mem_map 81000000
[ 0.000000] Normal zone: 64 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 8192 pages, LIFO batch:0
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
[ 0.000000] Kernel command line: board=UBNT-BM mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,7552k(firmware),256k(cfg)ro,64k(EEPROM)ro console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 27616K/32768K available (2990K kernel code, 174K rwdata, 756K rodata, 296K init, 198K bss, 5152K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Clocks: CPU:390.000MHz, DDR:390.000MHz, AHB:195.000MHz, Ref:40.000MHz
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9801335621 ns
[ 0.000013] sched_clock: 32 bits at 195MHz, resolution 5ns, wraps every 11012737021ns
[ 0.007859] Calibrating delay loop... 259.27 BogoMIPS (lpj=1296384)
[ 0.080537] pid_max: default: 32768 minimum: 301
[ 0.085319] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.091915] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.102743] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.113517] NET: Registered protocol family 16
[ 0.120061] MIPS: machine is Ubiquiti Bullet M
[ 0.126721] registering PCI controller with io_map_base unset
[ 0.357179] PCI host bridge to bus 0000:00
[ 0.361281] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
[ 0.368182] pci_bus 0000:00: root bus resource [io 0x0000]
[ 0.373728] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 0.380495] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.388431] pci 0000:00:00.0: [168c:002a] type 00 class 0x028000
[ 0.388474] pci 0000:00:00.0: fixup device configuration
[ 0.395026] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x0000ffff 64bit]
[ 0.395163] pci 0000:00:00.0: supports D1
[ 0.395187] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 0.395530] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 0.395581] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1000ffff 64bit]
[ 0.402872] pci 0000:00:00.0: using irq 40 for pin 1
[ 0.408968] clocksource: Switched to clocksource MIPS
[ 0.415854] NET: Registered protocol family 2
[ 0.421444] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.428402] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.434805] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.441299] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.447134] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.453795] NET: Registered protocol family 1
[ 0.458229] PCI: CLS 0 bytes, default 32
[ 0.464231] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.470521] Crashlog allocated RAM at address 0x1f00000
[ 0.495175] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.501058] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.514341] io scheduler noop registered
[ 0.518261] io scheduler deadline registered (default)
[ 0.523733] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.530718] console [ttyS0] disabled
[ 0.554351] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 12187500) is a 16550A
[ 0.563030] console [ttyS0] enabled
[ 0.570040] bootconsole [early0] disabled
[ 0.582496] m25p80 spi0.0: found mx25l6405d, expected m25p80
[ 0.588212] m25p80 spi0.0: mx25l6405d (8192 Kbytes)
[ 0.593216] 5 cmdlinepart partitions found on MTD device spi0.0
[ 0.599171] Creating 5 MTD partitions on "spi0.0":
[ 0.603989] 0x000000000000-0x000000040000 : "u-boot"
[ 0.611984] 0x000000040000-0x000000050000 : "u-boot-env"
[ 0.619662] 0x000000050000-0x0000007b0000 : "firmware"
[ 0.638852] 2 uimage-fw partitions found on MTD device firmware
[ 0.644868] 0x000000050000-0x0000001a0000 : "kernel"
[ 0.651750] 0x0000001a0000-0x0000007b0000 : "rootfs"
[ 0.658926] mtd: device 4 (rootfs) set to be root filesystem
[ 0.664753] 1 squashfs-split partitions found on MTD device rootfs
[ 0.671004] 0x000000550000-0x0000007b0000 : "rootfs_data"
[ 0.678725] 0x0000007b0000-0x0000007f0000 : "cfg"
[ 0.685800] 0x0000007f0000-0x000000800000 : "EEPROM"
[ 0.713752] libphy: ag71xx_mdio: probed
[ 1.302703] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:04 [uid=004dd041, driver=Generic PHY]
[ 1.312917] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[ 1.322177] NET: Registered protocol family 10
[ 1.332146] NET: Registered protocol family 17
[ 1.336720] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 1.349611] 8021q: 802.1Q VLAN Support v1.8
[ 1.362390] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[ 1.372040] Freeing unused kernel memory: 296K (80436000 - 80480000)
[ 2.887726] init: Console is alive
[ 2.891520] init: - watchdog -
[ 4.278086] usbcore: registered new interface driver usbfs
[ 4.283799] usbcore: registered new interface driver hub
[ 4.289318] usbcore: registered new device driver usb
[ 4.301475] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 4.310215] ehci-platform: EHCI generic platform driver
[ 4.319363] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 4.327317] ohci-platform: OHCI generic platform driver
[ 4.336163] init: - preinit -
[ 5.148612] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 5.181619] random: procd: uninitialized urandom read (4 bytes read, 8 bits of entropy available)
[ 8.484735] jffs2: notice: (361) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 8.502585] mount_root: switching to jffs2 overlay
[ 8.518273] urandom-seed: Seeding with /etc/urandom.seed
[ 8.810840] procd: - early -
[ 8.813863] procd: - watchdog -
[ 9.487850] procd: - ubus -
[ 9.541721] random: ubusd: uninitialized urandom read (4 bytes read, 15 bits of entropy available)
[ 9.551409] random: ubusd: uninitialized urandom read (4 bytes read, 15 bits of entropy available)
[ 9.560553] random: ubusd: uninitialized urandom read (4 bytes read, 15 bits of entropy available)
[ 9.570163] random: ubusd: uninitialized urandom read (4 bytes read, 15 bits of entropy available)
[ 9.579297] random: ubusd: uninitialized urandom read (4 bytes read, 15 bits of entropy available)
[ 9.589333] random: ubusd: uninitialized urandom read (4 bytes read, 15 bits of entropy available)
[ 9.598611] random: ubusd: uninitialized urandom read (4 bytes read, 15 bits of entropy available)
[ 9.608223] procd: - init -
[ 10.064115] Loading modules backported from Linux version wt-2016-10-03-1-g6fcb1a6
[ 10.071796] Backport generated by backports.git backports-20160324-9-g0e38f5c
[ 10.122372] batman_adv: B.A.T.M.A.N. advanced 2016.4 (compatibility version 15) loaded
[ 10.205329] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[ 10.216362] ath: phy0: Ignoring endianness difference in EEPROM magic bytes.
[ 10.225034] ath: EEPROM regdomain: 0x0
[ 10.225051] ath: EEPROM indicates default country code should be used
[ 10.225065] ath: doing EEPROM country->regdmn map search
[ 10.225093] ath: country maps to regdmn code: 0x3a
[ 10.225109] ath: Country alpha2 being used: US
[ 10.225122] ath: Regpair used: 0x3a
[ 10.240049] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 10.248689] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xb0000000, irq=40
[ 11.861887] random: jshn: uninitialized urandom read (4 bytes read, 19 bits of entropy available)
[ 11.993063] random: ubusd: uninitialized urandom read (4 bytes read, 19 bits of entropy available)
[ 18.833441] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 18.855566] IPv6: ADDRCONF(NETDEV_UP): br-pub: link is not ready
[ 21.215610] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 21.255512] device wlan0 entered promiscuous mode
[ 21.286637] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 21.293301] br-pub: port 1(wlan0) entered forwarding state
[ 21.298864] br-pub: port 1(wlan0) entered forwarding state
[ 21.335689] IPv6: ADDRCONF(NETDEV_CHANGE): br-pub: link becomes ready
[ 21.541225] IPv6: ADDRCONF(NETDEV_UP): mesh0: link is not ready
[ 21.594616] IPv6: ADDRCONF(NETDEV_CHANGE): mesh0: link becomes ready
[ 22.284927] batman_adv: bat0: Adding interface: mesh0
[ 22.290148] batman_adv: bat0: Interface activated: mesh0
[ 22.297750] 8021q: adding VLAN 0 to HW filter on device bat0
[ 22.362868] device bat0 entered promiscuous mode
[ 22.367627] br-pub: port 2(bat0) entered forwarding state
[ 22.373200] br-pub: port 2(bat0) entered forwarding state
[ 22.718089] batman_adv: bat0: bridge_loop_avoidance: Changing from: enabled to: disabled
[ 23.289035] br-pub: port 1(wlan0) entered forwarding state
[ 23.309325] batman_adv: bat0: No IGMP Querier present - multicast optimizations disabled
[ 23.317459] batman_adv: bat0: No MLD Querier present - multicast optimizations disabled
[ 24.369054] br-pub: port 2(bat0) entered forwarding state
[ 29.389161] batman_adv: bat0: IGMP Querier appeared
[ 38.069058] random: nonblocking pool is initialized
[ 44.920666] eth0: link up (100Mbps/Full duplex)
[ 44.925732] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 45.001214] batman_adv: bat0: Adding interface: eth0
[ 45.006233] batman_adv: bat0: The MTU of interface eth0 is too small (1500) to handle the transport of batman-adv packets. Packets going over this interface will be fragmented on layer2 which could impact the
performance. Setting the MTU to 1532 would solve the problem.
[ 45.030291] batman_adv: bat0: Interface activated: eth0
[ 50.459193] batman_adv: bat0: MLD Querier appeared
[ 67.509156] batman_adv: bat0: MLD Querier disappeared - multicast optimizations disabled
[ 77.549128] batman_adv: bat0: MLD Querier appeared
My LEDE diffconfig looks like this:
CONFIG_TARGET_ar71xx=y
CONFIG_TARGET_ar71xx_generic=y
CONFIG_TARGET_ar71xx_generic_DEVICE_ubnt-bullet-m=y
CONFIG_DEVEL=y
CONFIG_BUSYBOX_CUSTOM=y
CONFIG_ALFRED_NEEDS_lua=y
CONFIG_BUILD_LOG=y
CONFIG_BUSYBOX_CONFIG_MESG=y
CONFIG_BUSYBOX_CONFIG_PKILL=y
CONFIG_BUSYBOX_CONFIG_RDATE=y
# CONFIG_BUSYBOX_CONFIG_SHA256SUM is not set
CONFIG_KMOD_BATMAN_ADV_BATMAN_V=y
CONFIG_KMOD_BATMAN_ADV_BLA=y
CONFIG_KMOD_BATMAN_ADV_DAT=y
CONFIG_KMOD_BATMAN_ADV_DEBUGFS=y
CONFIG_KMOD_BATMAN_ADV_MCAST=y
CONFIG_LIBCURL_COOKIES=y
CONFIG_LIBCURL_FILE=y
CONFIG_LIBCURL_FTP=y
CONFIG_LIBCURL_HTTP=y
CONFIG_LIBCURL_NO_SMB="!"
CONFIG_LIBCURL_POLARSSL=y
CONFIG_LIBCURL_PROXY=y
CONFIG_OPENSSL_ENGINE_CRYPTO=y
CONFIG_OPENSSL_WITH_DEPRECATED=y
CONFIG_OPENSSL_WITH_EC=y
CONFIG_OPENSSL_WITH_NPN=y
CONFIG_OPENSSL_WITH_PSK=y
CONFIG_OPENSSL_WITH_SRP=y
CONFIG_PACKAGE_ALFRED_BATHOSTS=y
CONFIG_PACKAGE_ALFRED_VIS=y
CONFIG_PACKAGE_alfred=y
CONFIG_PACKAGE_batctl=y
CONFIG_PACKAGE_bridge=y
CONFIG_PACKAGE_curl=y
CONFIG_PACKAGE_diffutils=y
# CONFIG_PACKAGE_dnsmasq is not set
# CONFIG_PACKAGE_firewall is not set
CONFIG_PACKAGE_horst=y
CONFIG_PACKAGE_iftop=y
# CONFIG_PACKAGE_ip6tables is not set
CONFIG_PACKAGE_iperf3=y
# CONFIG_PACKAGE_iptables is not set
CONFIG_PACKAGE_kmod-batman-adv=y
CONFIG_PACKAGE_kmod-bridge=y
CONFIG_PACKAGE_kmod-crypto-aead=y
CONFIG_PACKAGE_kmod-crypto-crc32c=y
CONFIG_PACKAGE_kmod-crypto-hash=y
CONFIG_PACKAGE_kmod-crypto-manager=y
CONFIG_PACKAGE_kmod-crypto-null=y
CONFIG_PACKAGE_kmod-crypto-pcompress=y
# CONFIG_PACKAGE_kmod-ip6tables is not set
# CONFIG_PACKAGE_kmod-ipt-conntrack is not set
# CONFIG_PACKAGE_kmod-ipt-core is not set
# CONFIG_PACKAGE_kmod-ipt-nat is not set
# CONFIG_PACKAGE_kmod-lib-crc-ccitt is not set
CONFIG_PACKAGE_kmod-lib-crc16=y
CONFIG_PACKAGE_kmod-lib-crc32c=y
CONFIG_PACKAGE_kmod-llc=y
# CONFIG_PACKAGE_kmod-nf-conntrack is not set
# CONFIG_PACKAGE_kmod-nf-conntrack6 is not set
# CONFIG_PACKAGE_kmod-nf-ipt is not set
# CONFIG_PACKAGE_kmod-nf-ipt6 is not set
# CONFIG_PACKAGE_kmod-nf-nat is not set
# CONFIG_PACKAGE_kmod-ppp is not set
CONFIG_PACKAGE_kmod-stp=y
CONFIG_PACKAGE_libcurl=y
# CONFIG_PACKAGE_libip4tc is not set
# CONFIG_PACKAGE_libip6tc is not set
CONFIG_PACKAGE_liblua=y
CONFIG_PACKAGE_libncursesw=y
CONFIG_PACKAGE_libnetsnmp=y
CONFIG_PACKAGE_libopenssl=y
CONFIG_PACKAGE_libpcap=y
CONFIG_PACKAGE_libpcre=y
CONFIG_PACKAGE_libpolarssl=y
CONFIG_PACKAGE_libpopt=y
CONFIG_PACKAGE_libpthread=y
CONFIG_PACKAGE_librt=y
# CONFIG_PACKAGE_libxtables is not set
CONFIG_PACKAGE_lua=y
# CONFIG_PACKAGE_odhcp6c is not set
# CONFIG_PACKAGE_odhcpd is not set
# CONFIG_PACKAGE_ppp is not set
CONFIG_PACKAGE_procps-ng=y
CONFIG_PACKAGE_procps-ng-free=y
CONFIG_PACKAGE_procps-ng-kill=y
CONFIG_PACKAGE_procps-ng-pgrep=y
CONFIG_PACKAGE_procps-ng-pkill=y
CONFIG_PACKAGE_procps-ng-pmap=y
CONFIG_PACKAGE_procps-ng-ps=y
CONFIG_PACKAGE_procps-ng-pwdx=y
CONFIG_PACKAGE_procps-ng-skill=y
CONFIG_PACKAGE_procps-ng-slabtop=y
CONFIG_PACKAGE_procps-ng-snice=y
CONFIG_PACKAGE_procps-ng-tload=y
CONFIG_PACKAGE_procps-ng-top=y
CONFIG_PACKAGE_procps-ng-uptime=y
CONFIG_PACKAGE_procps-ng-vmstat=y
CONFIG_PACKAGE_procps-ng-w=y
CONFIG_PACKAGE_procps-ng-watch=y
CONFIG_PACKAGE_ptp-utils=y
CONFIG_PACKAGE_rsync=y
CONFIG_PACKAGE_snmpd=y
CONFIG_PACKAGE_tcpdump=y
CONFIG_PACKAGE_terminfo=y
CONFIG_PACKAGE_wget=y
CONFIG_PACKAGE_wireless-tools=y
CONFIG_PACKAGE_zlib=y
CONFIG_RSYNC_zlib=y
My uci show looks like this (system and wireless elided):
alfred.alfred=alfred
alfred.alfred.mode='master'
alfred.alfred.batmanif='bat0'
alfred.alfred.start_vis='1'
alfred.alfred.run_facters='1'
alfred.alfred.interface='br-pub'
alfred.alfred.disabled='0'
batman-adv.bat0=mesh
batman-adv.bat0.bridge_loop_avoidance='0'
dropbear.@dropbear[0]=dropbear
dropbear.@dropbear[0].PasswordAuth='on'
dropbear.@dropbear[0].RootPasswordAuth='on'
dropbear.@dropbear[0].Port='22'
network.loopback=interface
network.loopback.ifname='lo'
network.loopback.proto='static'
network.loopback.ipaddr='127.0.0.1'
network.loopback.netmask='255.0.0.0'
network.pub=interface
network.pub.type='bridge'
network.pub.proto='static'
network.pub.ip6assign='60'
network.pub.ifname='bat0'
network.pub.ipaddr='10.11.x.y'
network.pub.netmask='255.255.252.0'
network.pub.gateway='10.11.x.1'
network.pub.dns='10.11.x.1'
network.mesh=interface
network.mesh.mtu='1532'
network.mesh.proto='batadv'
network.mesh.mesh='bat0'
network.meshwire=interface
network.meshwire.proto='batadv'
network.meshwire.mesh='bat0'
network.meshwire.ifname='eth0'
|
|
09.03.2017 | 611 | Base system | Bug Report | Very Low | High | dnsmasq Ignore resolv file option forget at restart | All | Unconfirmed |
Task Description
If you set up dnsmasq to ignore resolv file it will ignore it until reboot is performed. To make ignore it again the option must be uncheck and apply and then check and apply again.
I have /etc/resolv.conf as a symlink to /tmp/resolv.conf, when the router boots up the contents are the dns offered from dhcp over the wan interface. When the ignore resolv option is checked or unchecked the contens are overwrited to search lan and nameserver 127.0.0.1 but it doesn’t seems to affect as if you uncheck ignore resolv the router resolv names, and when you check again the option it can resolv names even the contents still are search lan and nameserver 127.0.0.1.
I haven’t seen yet any other change that can cause the reboot to make dnsmasq follow resolv file when the option is checked until you uncheck-apply and check-apply.
|
|
09.03.2017 | 612 | Base system | Bug Report | Very Low | High | WAN to LAN leakage on MT7620 devices | Trunk | Unconfirmed |
Task Description
I am currently testing two MT7620 devices - the ZBT WE826 and the Sanlinking D240. During the first seconds of the boot, I see that packets leak between the WAN and LAN ports. Typically, this results in clients receiving a DHCP reply from my upstream router, rendering the clients without connectivity when the switch is properly initialized. I have also tested with the default firmware and do not see this behavior. Also, if I stop the devices in the bootloader, then packets do not leak until I resume boot again.
In order to try to solve this bug, I have tried to port some (at least to me) missing steps from the bootloader switch code and to the mt7620 switch driver in LEDE. This did not have an effect, at least not on the packet leak. A work-around I have found is to update u-boot and remove the input delay, so that the device will boot immediately. However, this is quite cumbersome to install and not very reliable. I suspect my luck with this work-around is more due to the timing of the DHCP clients in Ubuntu and Windows 10.
Does anyone have any idea as to what could be wrong and where to start looking?
Thanks in advance for any help.
|
|
17.04.2017 | 714 | Base system | Bug Report | Very Low | High | ARP/Broadcast does not reach other clients in the same ... | All | Unconfirmed |
Task Description
I have the default bridge with ethernet and WLAN in it. When i try to send data from a client to another, both connected to the same WLAN SSID, it doesn’t work (Destination unreachable). Wireshark shows that it sends endless ARP requests to Broadcast, but the other clients in that WLAN never get it (and therefore can’t answer). The broadcast gets still delivery to every client connected through Ethernet. If i create a second WLAN SSID (even on the same adapter) and and add it to the bridge, it gets also all broadcast packets from the other WLAN... So if i put the 2 clients in different WLAN SSIDs or ethernet they get the broadcast from each other, but not when both are connected to the same.
The isolate option is not set in the wireless config. Archer C5 v1 with latest LEDE snapshot (no difference to 17.01 stable or rc).
|
|
19.04.2017 | 717 | Base system | Bug Report | Very Low | High | WRT3200ACM USB 3.0 Problem | All | Unconfirmed |
Task Description
I can“t get my Seagate Expansion Portable 1TB STEA1000400 USB3.0 drive to be be recognized on the USB 3.0 port of the router after a reboot or cold start on WRT3200 but if i remove and hotplug the drive, it is automatically detected and can be mounted. It happens with images from Openwrt 15.05.1, LEDE 17.01.1 and many snapshots from both projects that i have installed. I have no problem with another usb2.0 drive from Samsung that is installed in another USB2.0 port.
After Cold START or REBOOT
root@LEDE:~# dmesg
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.9.20 (ag33e33@ubuntu) (gcc version 5.4.0 (LEDE GCC 5.4.0 r3963-7ae58be) ) #0 SMP Wed Apr 12 16:12:18 2017
[ 0.000000] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt:Machine model: Linksys WRT3200ACM
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] On node 0 totalpages: 131072
[ 0.000000] free_area_init_node: node 0, pgdat c0646900, node_mem_map dfbf9000
[ 0.000000] Normal zone: 1024 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 131072 pages, LIFO batch:31
[ 0.000000] percpu: Embedded 13 pages/cpu @dfbce000 s22732 r8192 d22324 u53248
[ 0.000000] pcpu-alloc: s22732 r8192 d22324 u53248 alloc=13*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048
[ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mtdblock6 ro rootdelay=1 rootfstype=jffs2 earlyprintk mtdparts=armada-nand:2048K(uboot)ro,128K(u_env),256K(s_env),256K@8064K(devinfo),1920K@8320K(sysdiag),80m@10m(kernel),74m@16m(rootfs),80m@90m(alt_kernel),74m@96m(alt_rootfs),160m@10m(ubifs),-@170m(syscfg)
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 512848K/524288K available (4545K kernel code, 180K rwdata, 1244K rodata, 280K init, 310K bss, 11440K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xe0800000 - 0xff800000 ( 496 MB)
lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
.text : 0xc0008000 - 0xc0478918 (4547 kB)
.init : 0xc05d4000 - 0xc061a000 ( 280 kB)
.data : 0xc061a000 - 0xc0647200 ( 181 kB)
.bss : 0xc0647200 - 0xc0694a00 ( 310 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] mvebu_mbus: [Firmware Warn]: deprecated mbus-mvebu Device Tree, suspend/resume will not work
[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9
[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9
[ 0.000000] L2C-310 D prefetch enabled, offset 1 lines
[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled
[ 0.000000] L2C-310 Coherent cache controller enabled, 16 ways, 1024 kB
[ 0.000000] L2C-310 Coherent: CACHE_ID 0x410054c9, AUX_CTRL 0x56070001
[ 0.000000] Selected CPU frequency (16) unsupported
[ 0.000000] Switching to timer-based delay loop, resolution 40ns
[ 0.000002] sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 85899345900ns
[ 0.000008] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns
[ 0.000114] Calibrating local timer... 933.22MHz.
[ 0.060032] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=250000)
[ 0.060037] pid_max: default: 32768 minimum: 301
[ 0.060076] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.060079] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.060274] CPU: Testing write buffer coherency: ok
[ 0.060365] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.060376] Setting up static identity map for 0x8280 - 0x82d8
[ 0.060434] mvebu-soc-id: MVEBU SoC ID=0x6820, Rev=0x4
[ 0.060494] mvebu-pmsu: Initializing Power Management Service Unit
[ 0.060904] Booting CPU 1
[ 0.061041] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.061070] Brought up 2 CPUs
[ 0.061075] SMP: Total of 2 processors activated (100.00 BogoMIPS).
[ 0.061078] CPU: All CPU(s) started in SVC mode.
[ 0.062739] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 0.062790] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.062796] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.062831] pinctrl core: initialized pinctrl subsystem
[ 0.063142] NET: Registered protocol family 16
[ 0.063575] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.090041] cpuidle: using governor ladder
[ 0.090171] mvebu-pmsu: CPU hotplug support is currently broken on Armada 38x: disabling
[ 0.090177] mvebu-pmsu: CPU idle is currently broken on Armada 38x: disabling
[ 0.120467] reg-fixed-voltage xhci0-vbus: could not find pctldev for node /soc/internal-regs/pinctrl@18000/xhci0-vbus-pins, deferring probe
[ 0.120607] SCSI subsystem initialized
[ 0.120687] libata version 3.00 loaded.
[ 0.120790] usbcore: registered new interface driver usbfs
[ 0.120815] usbcore: registered new interface driver hub
[ 0.120835] usbcore: registered new device driver usb
[ 0.121329] clocksource: Switched to clocksource armada_370_xp_clocksource
[ 0.121647] NET: Registered protocol family 2
[ 0.121869] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.121890] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.121920] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.121941] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.121952] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.122009] NET: Registered protocol family 1
[ 0.122021] PCI: CLS 0 bytes, default 64
[ 0.122803] Crashlog allocated RAM at address 0x3f00000
[ 0.122877] workingset: timestamp_bits=30 max_order=17 bucket_order=0
[ 0.124945] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.124953] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.125699] io scheduler noop registered
[ 0.125703] io scheduler deadline registered (default)
[ 0.126071] armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver
[ 0.126671] mvebu-pcie soc:pcie-controller: PCI host bridge to bus 0000:00
[ 0.126679] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff]
[ 0.126683] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff]
[ 0.126687] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.126701] pci 0000:00:01.0: [11ab:6820] type 01 class 0x060400
[ 0.126784] pci 0000:00:02.0: [11ab:6820] type 01 class 0x060400
[ 0.126859] PCI: bus0: Fast back to back transfers disabled
[ 0.126864] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.126870] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.126918] pci 0000:01:00.0: [11ab:2b40] type 00 class 0x020000
[ 0.126933] pci 0000:01:00.0: reg 0x10: [mem 0x40000000-0x401fffff 64bit pref]
[ 0.126943] pci 0000:01:00.0: reg 0x18: [mem 0x40200000-0x402fffff 64bit pref]
[ 0.127002] pci 0000:01:00.0: supports D1 D2
[ 0.127005] pci 0000:01:00.0: PME# supported from D0 D1 D3hot D3cold
[ 0.127068] PCI: bus1: Fast back to back transfers disabled
[ 0.127073] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 0.127132] pci 0000:02:00.0: [11ab:2b40] type 00 class 0x020000
[ 0.127151] pci 0000:02:00.0: reg 0x10: [mem 0x42000000-0x421fffff 64bit pref]
[ 0.127162] pci 0000:02:00.0: reg 0x18: [mem 0x42200000-0x422fffff 64bit pref]
[ 0.127244] pci 0000:02:00.0: supports D1 D2
[ 0.127246] pci 0000:02:00.0: PME# supported from D0 D1 D3hot D3cold
[ 0.127310] PCI: bus2: Fast back to back transfers disabled
[ 0.127315] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[ 0.127384] pci 0000:00:01.0: BAR 8: assigned [mem 0xe0000000-0xe02fffff]
[ 0.127390] pci 0000:00:02.0: BAR 8: assigned [mem 0xe0400000-0xe06fffff]
[ 0.127396] pci 0000:01:00.0: BAR 0: assigned [mem 0xe0000000-0xe01fffff 64bit pref]
[ 0.127405] pci 0000:01:00.0: BAR 2: assigned [mem 0xe0200000-0xe02fffff 64bit pref]
[ 0.127413] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 0.127418] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe02fffff]
[ 0.127425] pci 0000:02:00.0: BAR 0: assigned [mem 0xe0400000-0xe05fffff 64bit pref]
[ 0.127434] pci 0000:02:00.0: BAR 2: assigned [mem 0xe0600000-0xe06fffff 64bit pref]
[ 0.127443] pci 0000:00:02.0: PCI bridge to [bus 02]
[ 0.127448] pci 0000:00:02.0: bridge window [mem 0xe0400000-0xe06fffff]
[ 0.127646] mv_xor f1060800.xor: Marvell shared XOR driver
[ 0.181754] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr )
[ 0.181840] mv_xor f1060900.xor: Marvell shared XOR driver
[ 0.241717] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr )
[ 0.241857] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.242621] console [ttyS0] disabled
[ 0.262683] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 21, base_baud = 12500000) is a 16550A
[ 0.983287] console [ttyS0] enabled
[ 0.988691] loop: module loaded
[ 0.992090] ahci-mvebu f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode
[ 1.001176] ahci-mvebu f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs
[ 1.010274] scsi host0: ahci-mvebu
[ 1.013847] scsi host1: ahci-mvebu
[ 1.017348] ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 41
[ 1.025306] ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 41
[ 1.033594] pxa3xx-nand f10d0000.flash: This platform can't do DMA on this device
[ 1.041369] nand: device found, Manufacturer ID: 0x01, Chip ID: 0xda
[ 1.047747] nand: AMD/Spansion S34ML02G2
[ 1.051690] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 128
[ 1.059379] pxa3xx-nand f10d0000.flash: ECC strength 16, ECC step size 2048
[ 1.066556] Bad block table found at page 131008, version 0x01
[ 1.072752] Bad block table found at page 130944, version 0x01
[ 1.078863] 11 ofpart partitions found on MTD device pxa3xx_nand-0
[ 1.085074] Creating 11 MTD partitions on "pxa3xx_nand-0":
[ 1.090582] 0x000000000000-0x000000200000 : "u-boot"
[ 1.095830] 0x000000200000-0x000000220000 : "u_env"
[ 1.100951] 0x000000220000-0x000000260000 : "s_env"
[ 1.106089] 0x0000007e0000-0x000000820000 : "devinfo"
[ 1.111433] 0x000000820000-0x000000a00000 : "sysdiag"
[ 1.116797] 0x000000a00000-0x000005a00000 : "kernel1"
[ 1.122301] 0x000001000000-0x000005a00000 : "ubi"
[ 1.127404] 0x000005a00000-0x00000aa00000 : "kernel2"
[ 1.132905] 0x000006000000-0x00000aa00000 : "rootfs2"
[ 1.138362] 0x00000aa00000-0x000010000000 : "syscfg"
[ 1.143774] 0x000000260000-0x000000820000 : "unused_area"
[ 1.149701] libphy: Fixed MDIO Bus: probed
[ 1.154064] libphy: orion_mdio_bus: probed
[ 1.158297] mvneta_bm f10c8000.bm: Buffer Manager for network controller enabled
[ 1.166962] mvneta f1070000.ethernet eth0: Using hardware mac address 60:38:e0:b9:ea:c0
[ 1.175959] mvneta f1034000.ethernet eth1: Using random mac address a2:8d:5e:6d:ee:98
[ 1.183881] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.190435] ehci-pci: EHCI PCI platform driver
[ 1.194928] ehci-platform: EHCI generic platform driver
[ 1.200245] ehci-orion: EHCI orion driver
[ 1.204336] orion-ehci f1058000.usb: EHCI Host Controller
[ 1.209765] orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1
[ 1.217412] orion-ehci f1058000.usb: irq 37, io mem 0xf1058000
[ 1.251329] orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00
[ 1.257480] hub 1-0:1.0: USB hub found
[ 1.261254] hub 1-0:1.0: 1 port detected
[ 1.265551] usbcore: registered new interface driver usb-storage
[ 1.271723] armada38x-rtc f10a3800.rtc: rtc core: registered f10a3800.rtc as rtc0
[ 1.279341] i2c /dev entries driver
[ 1.294252] orion_wdt: Initial timeout 171 sec
[ 1.298933] sdhci: Secure Digital Host Controller Interface driver
[ 1.305146] sdhci: Copyright(c) Pierre Ossman
[ 1.362546] ata1: SATA link down (SStatus 0 SControl 300)
[ 1.367991] ata2: SATA link down (SStatus 0 SControl 300)
[ 1.371354] mmc0: SDHCI controller on f10d8000.sdhci [f10d8000.sdhci] using ADMA
[ 1.371428] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.377154] marvell-cesa f1090000.crypto: CESA device successfully registered
[ 1.377556] NET: Registered protocol family 10
[ 1.391590] NET: Registered protocol family 17
[ 1.391604] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 1.391605] 8021q: 802.1Q VLAN Support v1.8
[ 1.391661] Registering SWP/SWPB emulation handler
[ 1.392791] xhci-hcd f10f8000.usb3: xHCI Host Controller
[ 1.392803] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 2
[ 1.392861] xhci-hcd f10f8000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x00010010
[ 1.392881] xhci-hcd f10f8000.usb3: irq 44, io mem 0xf10f8000
[ 1.393134] hub 2-0:1.0: USB hub found
[ 1.393160] hub 2-0:1.0: 1 port detected
[ 1.393247] xhci-hcd f10f8000.usb3: xHCI Host Controller
[ 1.393253] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 3
[ 1.393292] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
[ 1.393478] hub 3-0:1.0: USB hub found
[ 1.393501] hub 3-0:1.0: 1 port detected
[ 1.393820] UBI: auto-attach mtd6
[ 1.393824] ubi0: attaching mtd6
[ 1.397930] random: fast init done
[ 1.401551] mmc0: new high speed SDIO card at address 0001
[ 1.593092] ubi0: scanning is finished
[ 1.601334] ubi0: attached mtd6 (name "ubi", size 74 MiB)
[ 1.606756] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 1.613664] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 1.620479] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 1.627475] ubi0: good PEBs: 592, bad PEBs: 0, corrupted PEBs: 0
[ 1.633508] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[ 1.640759] ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 1419003487
[ 1.649932] ubi0: available PEBs: 0, total reserved PEBs: 592, PEBs reserved for bad PEB handling: 40
[ 1.659197] ubi0: background thread "ubi_bgt0d" started, PID 668
[ 1.659208] usb 1-1: new high-speed USB device number 2 using orion-ehci
[ 1.659643] block ubiblock0_0: created from ubi0:0(rootfs)
[ 1.659645] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[ 1.659829] mvsw61xx 10.mvsw61xx: Found MV88E6352 at f1072004.mdio-mi:10
[ 1.659832] mvsw61xx 10.mvsw61xx: Using direct addressing
[ 1.671972] armada38x-rtc f10a3800.rtc: setting system clock to 2101-11-05 12:45:50 UTC (4160637950)
[ 1.705850] Waiting 1 sec before mounting root device...
[ 1.852932] usb-storage 1-1:1.0: USB Mass Storage device detected
[ 1.859142] scsi host2: usb-storage 1-1:1.0
[ 2.722974] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 2.730260] Freeing unused kernel memory: 280K (c05d4000 - c061a000)
[ 2.736655] This architecture does not have kernel memory protection.
[ 2.855724] init: Console is alive
[ 2.859203] init: - watchdog -
[ 2.924338] scsi 2:0:0:0: Direct-Access Samsung S2 Portable PQ: 0 ANSI: 2 CCS
[ 3.111498] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 3.151660] sd 2:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB)
[ 3.159777] sd 2:0:0:0: [sda] Write Protect is off
[ 3.164597] sd 2:0:0:0: [sda] Mode Sense: 28 00 00 00
[ 3.165152] sd 2:0:0:0: [sda] No Caching mode page found
[ 3.170490] sd 2:0:0:0: [sda] Assuming drive cache: write through
[ 3.179038] sda: sda1
[ 3.183653] sd 2:0:0:0: [sda] Attached SCSI disk
[ 3.188738] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 3.195221] ohci-platform: OHCI generic platform driver
[ 3.200902] uhci_hcd: USB Universal Host Controller Interface driver
[ 3.207556] ohci-pci: OHCI PCI platform driver
[ 3.212156] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 3.228593] init: - preinit -
[ 3.422394] mvneta f1070000.ethernet tmp0: renamed from eth0
[ 3.462586] mvneta f1034000.ethernet eth0: renamed from eth1
[ 3.512510] mvneta f1070000.ethernet eth1: renamed from tmp0
[ 3.833291] mvneta f1034000.ethernet eth0: configuring for fixed link mode
[ 3.840562] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 3.846607] mvneta f1034000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[ 3.854578] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 5.909798] mount_root: loading kmods from internal overlay
[ 5.921475] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[ 5.929503] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[ 6.328768] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 806
[ 6.357145] UBIFS (ubi0:1): recovery needed
[ 6.403932] random: crng init done
[ 6.431762] UBIFS (ubi0:1): recovery completed
[ 6.436249] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[ 6.444117] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 6.454076] UBIFS (ubi0:1): FS size: 61329408 bytes (58 MiB, 483 LEBs), journal size 3047424 bytes (2 MiB, 24 LEBs)
[ 6.464556] UBIFS (ubi0:1): reserved for root: 2896739 bytes (2828 KiB)
[ 6.471198] UBIFS (ubi0:1): media format: w4/r0 (latest is w4/r0), UUID DEE50754-EFFE-4990-A7A6-C97266C9BEF0, small LPT model
[ 6.483473] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[ 6.493882] block: extroot: not configured
[ 6.531369] UBIFS (ubi0:1): un-mount UBI device 0
[ 6.536097] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" stops
[ 6.544028] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 809
[ 6.591527] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[ 6.599392] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 6.609356] UBIFS (ubi0:1): FS size: 61329408 bytes (58 MiB, 483 LEBs), journal size 3047424 bytes (2 MiB, 24 LEBs)
[ 6.619838] UBIFS (ubi0:1): reserved for root: 2896739 bytes (2828 KiB)
[ 6.626483] UBIFS (ubi0:1): media format: w4/r0 (latest is w4/r0), UUID DEE50754-EFFE-4990-A7A6-C97266C9BEF0, small LPT model
[ 6.641627] mount_root: loading kmods from internal overlay
[ 6.652909] kmodloader: loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
[ 6.670201] kmodloader: done loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
[ 7.078279] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[ 7.086484] block: extroot: not configured
[ 7.132013] mount_root: switching to ubifs overlay
[ 7.176201] ubi1: attaching mtd9
[ 7.407547] ubi1: scanning is finished
[ 7.415742] ubi1: attached mtd9 (name "syscfg", size 86 MiB)
[ 7.421435] ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 7.428338] ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 7.435155] ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 7.442148] ubi1: good PEBs: 680, bad PEBs: 8, corrupted PEBs: 0
[ 7.448177] ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 7.455430] ubi1: max/mean erase counter: 6/4, WL threshold: 4096, image sequence number: 1148089792
[ 7.464603] ubi1: available PEBs: 0, total reserved PEBs: 680, PEBs reserved for bad PEB handling: 32
[ 7.473869] ubi1: background thread "ubi_bgt1d" started, PID 824
[ 7.485213] UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 828
[ 7.537764] UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "syscfg"
[ 7.545202] UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 7.555161] UBIFS (ubi1:0): FS size: 80375808 bytes (76 MiB, 633 LEBs), journal size 4063232 bytes (3 MiB, 32 LEBs)
[ 7.565642] UBIFS (ubi1:0): reserved for root: 3796347 bytes (3707 KiB)
[ 7.572287] UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID A5EAB2F8-92D3-4D0B-A69A-9F6CA9A608B3, small LPT model
[ 7.585463] urandom-seed: Seeding with /etc/urandom.seed
[ 7.684142] procd: - early -
[ 7.687055] procd: - watchdog -
[ 8.315049] procd: - ubus -
[ 8.371904] procd: - init -
[ 8.546612] kmodloader: loading kernel modules from /etc/modules.d/*
[ 8.557859] tun: Universal TUN/TAP device driver, 1.6
[ 8.562965] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 8.571391] Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
[ 8.580401] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 8.587876] cryptodev: driver 1.8 loaded.
[ 8.592340] Loading modules backported from Linux version wt-2017-01-31-0-ge882dff19e7f
[ 8.600387] Backport generated by backports.git backports-20160324-13-g24da7d3c
[ 8.615059] <<Marvell 802.11ac Wireless Network Driver version 10.3.2.0-20170110>>
[ 8.622702] pci 0000:00:01.0: enabling device (0140 -> 0142)
[ 8.628443] ieee80211 phy0: priv->iobase0 = e0f80000
[ 8.628454] ieee80211 phy0: priv->iobase1 = e1200000
[ 8.628463] ieee80211 phy0: priv->pcmd_buf = ddf08000 priv->pphys_cmd_buf = 1df08000
[ 8.636458] ieee80211 phy0: fw download start
[ 8.699990] ieee80211 phy0: FwSize = 207660 downloaded Size = 207660 curr_iteration 65522
[ 12.431324] ieee80211 phy0: fw download complete
[ 12.431783] ieee80211 phy0: pcmd = ddf08000
[ 12.449817] ieee80211 phy0: firmware version: 0x7080004
[ 12.809338] ieee80211 phy0: firmware region code: 10
[ 12.851995] ieee80211 phy0: 2G disabled, 5G enabled
[ 12.856895] ieee80211 phy0: 4 TX antennas, 4 RX antennas
[ 12.862298] pci 0000:00:02.0: enabling device (0140 -> 0142)
[ 12.868032] ieee80211 phy1: priv->iobase0 = e1380000
[ 12.868043] ieee80211 phy1: priv->iobase1 = e1600000
[ 12.868052] ieee80211 phy1: priv->pcmd_buf = dddf0000 priv->pphys_cmd_buf = 1ddf0000
[ 12.874418] ieee80211 phy1: fw download start
[ 12.939175] ieee80211 phy1: FwSize = 207660 downloaded Size = 207660 curr_iteration 65527
[ 14.327325] ieee80211 phy1: fw download complete
[ 14.327812] ieee80211 phy1: pcmd = dddf0000
[ 14.345344] ieee80211 phy1: firmware version: 0x7080004
[ 14.706323] ieee80211 phy1: firmware region code: 10
[ 14.750021] ieee80211 phy1: 2G enabled, 5G disabled
[ 14.754934] ieee80211 phy1: 4 TX antennas, 4 RX antennas
[ 14.762803] u32 classifier
[ 14.765522] input device check on
[ 14.769196] Actions configured
[ 14.773037] Mirror/redirect action on
[ 14.778285] nf_conntrack version 0.5.0 (8192 buckets, 32768 max)
[ 14.790080] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 14.799009] mwifiex: rx work enabled, cpus 2
[ 14.846998] usbcore: registered new interface driver ums-alauda
[ 14.853672] usbcore: registered new interface driver ums-cypress
[ 14.860218] usbcore: registered new interface driver ums-datafab
[ 14.866723] usbcore: registered new interface driver ums-freecom
[ 14.873187] usbcore: registered new interface driver ums-isd200
[ 14.879542] usbcore: registered new interface driver ums-jumpshot
[ 14.886112] usbcore: registered new interface driver ums-karma
[ 14.892282] usbcore: registered new interface driver ums-sddr09
[ 14.898499] usbcore: registered new interface driver ums-sddr55
[ 14.904752] usbcore: registered new interface driver ums-usbat
[ 14.917781] xt_time: kernel timezone is -0000
[ 14.925132] PPP generic driver version 2.4.2
[ 14.929843] NET: Registered protocol family 24
[ 14.935112] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 15.469997] mwifiex_sdio mmc0:0001:1: info: FW download over, size 391772 bytes
[ 15.831665] mwifiex_sdio mmc0:0001:1: WLAN FW is active
[ 15.864262] mwifiex_sdio mmc0:0001:1: CMD_RESP: cmd 0x242 error, result=0x2
[ 15.871261] mwifiex_sdio mmc0:0001:1: mwifiex_process_cmdresp: cmd 0x242 failed during initialization
[ 15.890625] mwifiex_sdio mmc0:0001:1: info: MWIFIEX VERSION: mwifiex 1.0 (15.68.7.p5)
[ 15.898674] mwifiex_sdio mmc0:0001:1: driver_version = mwifiex 1.0 (15.68.7.p5)
[ 16.052347] mvneta f1034000.ethernet eth0: configuring for fixed link mode
[ 16.059309] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 16.065375] mvneta f1034000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[ 16.073372] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 16.081683] br-lan: port 1(eth0.1) entered blocking state
[ 16.087106] br-lan: port 1(eth0.1) entered disabled state
[ 16.092675] device eth0.1 entered promiscuous mode
[ 16.097485] device eth0 entered promiscuous mode
[ 16.103227] br-lan: port 1(eth0.1) entered blocking state
[ 16.108650] br-lan: port 1(eth0.1) entered forwarding state
[ 16.122758] mvneta f1070000.ethernet eth1: configuring for fixed link mode
[ 16.130044] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 16.136169] mvneta f1070000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[ 16.144170] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 16.342477] pppoe-wan: renamed from ppp0
[ 16.900336] ieee80211 phy1: change: 0xffffffff
[ 17.006509] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 17.137396] ieee80211 phy0: change: 0xffffffff
[ 17.271596] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 17.277594] br-lan: port 2(wlan1) entered blocking state
[ 17.282955] br-lan: port 2(wlan1) entered disabled state
[ 17.288408] device wlan1 entered promiscuous mode
[ 17.293166] br-lan: port 2(wlan1) entered blocking state
[ 17.298502] br-lan: port 2(wlan1) entered forwarding state
[ 17.304255] br-lan: port 2(wlan1) entered disabled state
[ 17.309734] br-lan: port 3(wlan0) entered blocking state
[ 17.315091] br-lan: port 3(wlan0) entered disabled state
[ 17.320543] device wlan0 entered promiscuous mode
[ 17.327109] ieee80211 phy0: change: 0x100
[ 17.344423] ieee80211 phy0: change: 0x40
[ 17.380440] ieee80211 phy1: change: 0x100
[ 17.392530] ieee80211 phy1: change: 0x42
[ 17.593821] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 17.600257] br-lan: port 2(wlan1) entered blocking state
[ 17.605603] br-lan: port 2(wlan1) entered forwarding state
[ 17.611269] ieee80211 phy0: change: 0x40
[ 17.671185] ieee80211 phy1: change: 0x20
[ 17.861365] ieee80211 phy0: change: 0x40
[ 17.993370] ieee80211 phy0: change: 0x100
[ 18.060535] ieee80211 phy0: change: 0x100
[ 18.073629] ieee80211 phy0: change: 0x42
[ 18.341340] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 18.347812] br-lan: port 3(wlan0) entered blocking state
[ 18.353170] br-lan: port 3(wlan0) entered forwarding state
root@LEDE:~# lsusb
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 002: ID 04e8:1f05 Samsung Electronics Co., Ltd S2 Portable [JMicron] (500GB)
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
After i remove the cable and hotplug i get this additional lines in DMESG:
#
[ 527.103849] usb 3-1: new SuperSpeed USB device number 2 using xhci-hcd
[ 527.134880] usb-storage 3-1:1.0: USB Mass Storage device detected
[ 527.141155] scsi host3: usb-storage 3-1:1.0
[ 528.154087] scsi 3:0:0:0: Direct-Access Seagate Expansion 1805 PQ: 0 ANSI: 6
[ 529.455313] sd 3:0:0:0: [sdb] 1953525167 512-byte logical blocks: (1.00 TB/932 GiB)
[ 529.463210] sd 3:0:0:0: [sdb] Write Protect is off
[ 529.468032] sd 3:0:0:0: [sdb] Mode Sense: 33 00 00 08
[ 529.473381] sd 3:0:0:0: [sdb] No Caching mode page found
[ 529.478724] sd 3:0:0:0: [sdb] Assuming drive cache: write through
[ 529.499962] sdb: sdb1 sdb2
[ 529.503903] sd 3:0:0:0: [sdb] Attached SCSI disk
[ 612.132851] EXT4-fs (sdb2): mounted filesystem with ordered data mode. Opts:
root@LEDE:~# lsusb
Bus 003 Device 002: ID 0bc2:231b Seagate RSS LLC
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 002: ID 04e8:1f05 Samsung Electronics Co., Ltd S2 Portable [JMicron] (500GB)
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
|
|
25.07.2017 | 931 | Base system | Bug Report | Very Low | High | Onboard Bluetooth not working on Raspberry Pi 3 B | All | Assigned |
Task Description
I have tried LEDE 17.01.1 and 17.01.2 and i can’t get bluetooth running on raspberry pi 3.
It will not flash the firmware for the bluetooth controller on rpi3, when device is brought up:
root@LEDE:~# /usr/bin/hciattach /dev/ttyAMA0 bcm43xx 921600 noflow - bcm43xx_init Patch not found for BCM43430A1, continue anyway Set Controller UART speed to 921600 bit/s Device setup complete
Instead of patch not found it should produce: Flash firmware /lib/firmware/brcm/BCM43430A1.hcd
I could not find this firmware via opkg, so i used a file from OpenELEC at https://github.com/OpenELEC/misc-firmware/tree/master/firmware/brcm
This however won’t load and bluetooth is not initialized correctly and unusable:
root@LEDE:~# /usr/bin/hciattach /dev/ttyAMA0 bcm43xx 921600 noflow - bcm43xx_init Flash firmware /lib/firmware/brcm/BCM43430A1.hcd Initialization timed out
|