You signed in with another tab or window. Reload to refresh your session.You signed out in another tab or window. Reload to refresh your session.You switched accounts on another tab or window. Reload to refresh your session.Dismiss alert
Trying to start hostapd fails if channel is set to 'auto' in UCI resulting in channel=acs_survey ending up in hostapd.conf.
Configuration file: /var/run/hostapd-phy0.conf
wlan0: interface state UNINITIALIZED->COUNTRY_UPDATE
ACS: Automatic channel selection started, this may take a bit
wlan0: interface state COUNTRY_UPDATE->ACS
wlan0: ACS-STARTED
ACS: Unable to collect survey data
ACS: All study options have failed
Interface initialization failed
wlan0: interface state ACS->DISABLED
wlan0: AP-DISABLED
ACS: Possibly channel configuration is invalid, please report this along with your config file.
ACS: Failed to start
wlan0: AP-DISABLED
hostapd_free_hapd_data: Interface wlan0 wasn't started
nl80211: deinit ifname=wlan0 disabled_11b_rates=0
wlan0: interface state DISABLED->DISABLED
wlan0: interface state DISABLED->DISABLED
wlan0: AP-DISABLED
hostapd_free_hapd_data: Interface wlan0 wasn't started
This needs more info, like the particular radio type in use. However I have 2 wireless interfaces (ath9k & ath10k) set to use 'auto'/acs_survey and hostapd works fine:
dangowrt:
Trying to start hostapd fails if channel is set to 'auto' in UCI resulting in
channel=acs_survey
ending up in hostapd.conf.Configuration file: /var/run/hostapd-phy0.conf
wlan0: interface state UNINITIALIZED->COUNTRY_UPDATE
ACS: Automatic channel selection started, this may take a bit
wlan0: interface state COUNTRY_UPDATE->ACS
wlan0: ACS-STARTED
ACS: Unable to collect survey data
ACS: All study options have failed
Interface initialization failed
wlan0: interface state ACS->DISABLED
wlan0: AP-DISABLED
ACS: Possibly channel configuration is invalid, please report this along with your config file.
ACS: Failed to start
wlan0: AP-DISABLED
hostapd_free_hapd_data: Interface wlan0 wasn't started
nl80211: deinit ifname=wlan0 disabled_11b_rates=0
wlan0: interface state DISABLED->DISABLED
wlan0: interface state DISABLED->DISABLED
wlan0: AP-DISABLED
hostapd_free_hapd_data: Interface wlan0 wasn't started
auto-generated configuration:
driver=nl80211
logger_syslog=127
logger_syslog_level=2
logger_stdout=127
logger_stdout_level=2
country_code=DE
ieee80211d=1
ieee80211h=1
hw_mode=a
channel=acs_survey
ieee80211n=1
ht_coex=0
ht_capab=[HT40+][LDPC][SHORT-GI-20][SHORT-GI-40][TX-STBC][RX-STBC1]
vht_oper_chwidth=1
vht_oper_centr_freq_seg0_idx=-6
ieee80211ac=1
vht_capab=[RXLDPC][SHORT-GI-80][TX-STBC-2BY1][RX-STBC-1][MAX-A-MPDU-LEN-EXP0]
interface=wlan0
ctrl_interface=/var/run/hostapd
ap_isolate=1
disassoc_low_ack=1
preamble=1
wmm_enabled=1
ignore_broadcast_ssid=0
uapsd_advertisement_enabled=1
wpa_passphrase=topsecretpassword
auth_algs=1
wpa=2
wpa_pairwise=CCMP
ssid=OpenWrt
bridge=br-lan
wpa_key_mgmt=WPA-PSK
okc=0
disable_pmksa_caching=1
bssid=78:a3:51:0d:12:f5
The text was updated successfully, but these errors were encountered: