OpenWrt/LEDE Project

  • Status Unconfirmed
  • Percent Complete
    0%
  • Task Type Bug Report
  • Category Base system
  • Assigned To No-one
  • Operating System All
  • Severity Low
  • Priority Very Low
  • Reported Version Trunk
  • Due in Version Undecided
  • Due Date Undecided
  • Private
Attached to Project: OpenWrt/LEDE Project
Opened by Rob White - 14.02.2017

FS#514 - Any files copied to flash gone after reboot17.01.0-rc2 x86-geode-combined-squashfs.img

PCEngines Alix with lede-17.01.0-rc2-r3131-42f3c1f-x86-geode-combined-squashfs.img

Boots fine.

Any software installed or files copied to flash disappear after reboot.

However LAN ethernet IP address is (usually)remembered but did get reset on one occasion.
But WiFi config of a USB dongle is always lost.

The board has a Lexar 16GB UDMA7 CF card. This config works fine with OpenWrt CC.

Reflashing, changing the flash card etc makes no difference.

Admin
Jo-Philipp Wich commented on 14.02.2017 19:06

Can you please post the output of "mount" and "dmesg" after boot?

Rob White commented on 15.02.2017 11:14

Hi Jo-Phillipp
Here is the output as requested. Prior to this I had installed sftp and copied folders/files to /www
After this reboot sftp no longer installed and the copied folders/files missing.

 \  DE    \  /    Reboot (17.01.0-rc2, r3131-42f3c1f)
  \________\/    -----------------------------------------------------------

root@LEDE:~# mount
/dev/root on /rom type squashfs (ro,relatime)
proc on /proc type proc (rw,nosuid,nodev,noexec,noatime)
sysfs on /sys type sysfs (rw,nosuid,nodev,noexec,noatime)
tmpfs on /tmp type tmpfs (rw,nosuid,nodev,noatime)
/dev/loop0 on /overlay type f2fs (rw,noatime,background_gc=on,user_xattr,inline_data,extent_cache,active_logs=6)
overlayfs:/overlay on / type overlay (rw,noatime,lowerdir=/,upperdir=/overlay/upper,workdir=/overlay/work)
tmpfs on /dev type tmpfs (rw,nosuid,relatime,size=512k,mode=755)
devpts on /dev/pts type devpts (rw,nosuid,noexec,relatime,mode=600)
debugfs on /sys/kernel/debug type debugfs (rw,noatime)
root@LEDE:~# dmesg
[ 0.000000] Linux version 4.4.47 (buildbot@builds-02.infra.lede-project.org) (gcc version 5.4.0 (LEDE GCC 5.4.0 r3103-1b51a49) ) #0 Tue Feb 7 08:32:47 2017
[ 0.000000] x86/fpu: Legacy x87 FPU detected.
[ 0.000000] x86/fpu: Using 'lazy' FPU context switches.
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009ffff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000000fffffff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000fff00000-0x00000000ffffffff] reserved
[ 0.000000] Notice: NX (Execute Disable) protection missing in CPU!
[ 0.000000] DMI not present or invalid.
[ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable =⇒ reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] e820: last_pfn = 0x10000 max_arch_pfn = 0x100000
[ 0.000000] MTRR: Disabled
[ 0.000000] x86/PAT: MTRRs disabled, skipping PAT initialization too.
[ 0.000000] x86/PAT: Configuration [0-7]: WB WT UC- UC WB WT UC- UC
[ 0.000000] initial memory mapped: [mem 0x00000000-0x017fffff]
[ 0.000000] Base memory trampoline at [c009b000] 9b000 size 16384
[ 0.000000] 256MB LOWMEM available.
[ 0.000000] mapped low ram: 0 - 10000000
[ 0.000000] low ram: 0 - 10000000
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000000001000-0x0000000000ffffff]
[ 0.000000] Normal [mem 0x0000000001000000-0x000000000fffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000001000-0x000000000009ffff]
[ 0.000000] node 0: [mem 0x0000000000100000-0x000000000fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000001000-0x000000000fffffff]
[ 0.000000] On node 0 totalpages: 65439
[ 0.000000] free_area_init_node: node 0, pgdat c143c6a0, node_mem_map cfe00020
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 3999 pages, LIFO batch:0
[ 0.000000] Normal zone: 480 pages used for memmap
[ 0.000000] Normal zone: 61440 pages, LIFO batch:15
[ 0.000000] Using APIC driver default
[ 0.000000] No local APIC present or hardware disabled
[ 0.000000] APIC: disable apic facility
[ 0.000000] APIC: switched to apic NOOP
[ 0.000000] e820: [mem 0x10000000-0xffefffff] available for PCI devices
[ 0.000000] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64927
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz root=PARTUUID=e77f60e1-02 rootfstype=squashfs rootwait console=tty0 console=ttyS0,38400n8 noinitrd
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Initializing CPU#0
[ 0.000000] Memory: 254420K/261756K available (3443K kernel code, 238K rwdata, 676K rodata, 288K init, 264K bss, 7336K reserved, 0K cma-reserved)
[ 0.000000] virtual kernel memory layout:
[ 0.000000] fixmap : 0xfffa4000 - 0xfffff000 ( 364 kB)
[ 0.000000] vmalloc : 0xd0800000 - 0xfffa2000 ( 759 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] .init : 0xc1445000 - 0xc148d000 ( 288 kB)
[ 0.000000] .data : 0xc135d0dd - 0xc1443900 ( 922 kB)
[ 0.000000] .text : 0xc1000000 - 0xc135d0dd (3444 kB)
[ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:2304 nr_irqs:32 16
[ 0.000000] CPU 0 irqstacks, hard=cf808000 soft=cf80a000
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] console [ttyS0] enabled
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.000000] tsc: Detected 498.018 MHz processor
[ 0.030008] Calibrating delay loop (skipped), value calculated using timer frequency.. 996.03 BogoMIPS (lpj=4980180)
[ 0.050011] pid_max: default: 32768 minimum: 301
[ 0.060120] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.070015] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.080755] Last level iTLB entries: 4KB 0, 2MB 0, 4MB 0
[ 0.090013] Last level dTLB entries: 4KB 0, 2MB 0, 4MB 0, 1GB 0
[ 0.100007] CPU: Geode(TM) Integrated Processor by AMD PCS (family: 0x5, model: 0xa, stepping: 0x2)
[ 0.130297] Performance Events: no PMU driver, software events only.
[ 0.151638] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.161073] NET: Registered protocol family 16
[ 0.181157] cpuidle: using governor ladder
[ 0.190243] clocksource: pit: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1601818034827 ns
[ 0.201696] PCI: PCI BIOS revision 2.10 entry at 0xfced9, last bus=0
[ 0.210010] PCI: Using configuration type 1 for base access
[ 0.243264] SCSI subsystem initialized
[ 0.250508] libata version 3.00 loaded.
[ 0.250706] usbcore: registered new interface driver usbfs
[ 0.260101] usbcore: registered new interface driver hub
[ 0.270074] usbcore: registered new device driver usb
[ 0.280259] dmi: Firmware registration failed.
[ 0.290010] PCI: Probing PCI hardware
[ 0.300011] PCI: root bus 00: using default resources
[ 0.300030] PCI: Probing PCI hardware (bus 00)
[ 0.300171] PCI host bridge to bus 0000:00
[ 0.310025] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
[ 0.320022] pci_bus 0000:00: root bus resource [mem 0x00000000-0xffffffff]
[ 0.330020] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.340058] pci 0000:00:01.0: [1022:2080] type 00 class 0x060000
[ 0.340109] pci 0000:00:01.0: [Firmware Bug]: reg 0x10: invalid BAR (can't size)
[ 0.350364] pci 0000:00:01.2: [1022:2082] type 00 class 0x101000
[ 0.350429] pci 0000:00:01.2: reg 0x10: [mem 0xefff4000-0xefff7fff]
[ 0.350843] pci 0000:00:09.0: [1106:3053] type 00 class 0x020000
[ 0.350889] pci 0000:00:09.0: reg 0x10: [io 0x1000-0x10ff]
[ 0.350921] pci 0000:00:09.0: reg 0x14: [mem 0xe0000000-0xe00000ff]
[ 0.351007] pci 0000:00:09.0: supports D1 D2
[ 0.351029] pci 0000:00:09.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.351274] pci 0000:00:0b.0: [1106:3053] type 00 class 0x020000
[ 0.351319] pci 0000:00:0b.0: reg 0x10: [io 0x1400-0x14ff]
[ 0.351349] pci 0000:00:0b.0: reg 0x14: [mem 0xe0040000-0xe00400ff]
[ 0.351432] pci 0000:00:0b.0: supports D1 D2
[ 0.351452] pci 0000:00:0b.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.351706] pci 0000:00:0f.0: [1022:2090] type 00 class 0x060100
[ 0.351829] pci 0000:00:0f.0: reg 0x10: [io 0x6000-0x6007]
[ 0.351932] pci 0000:00:0f.0: reg 0x14: [io 0x6100-0x61ff]
[ 0.352035] pci 0000:00:0f.0: reg 0x18: [io 0x6200-0x623f]
[ 0.352189] pci 0000:00:0f.0: reg 0x20: [io 0x9d00-0x9d7f]
[ 0.352293] pci 0000:00:0f.0: reg 0x24: [io 0x9c00-0x9c3f]
[ 0.352632] pci 0000:00:0f.2: [1022:209a] type 00 class 0x010180
[ 0.352859] pci 0000:00:0f.2: reg 0x20: [io 0xff00-0xff0f]
[ 0.352965] pci 0000:00:0f.2: legacy IDE quirk: reg 0x10: [io 0x01f0-0x01f7]
[ 0.360020] pci 0000:00:0f.2: legacy IDE quirk: reg 0x14: [io 0x03f6]
[ 0.370021] pci 0000:00:0f.2: legacy IDE quirk: reg 0x18: [io 0x0170-0x0177]
[ 0.380021] pci 0000:00:0f.2: legacy IDE quirk: reg 0x1c: [io 0x0376]
[ 0.390287] pci 0000:00:0f.4: [1022:2094] type 00 class 0x0c0310
[ 0.390392] pci 0000:00:0f.4: reg 0x10: [mem 0xefffe000-0xefffefff]
[ 0.390658] pci 0000:00:0f.4: PME# supported from D0 D3hot D3cold
[ 0.390939] pci 0000:00:0f.5: [1022:2095] type 00 class 0x0c0320
[ 0.391046] pci 0000:00:0f.5: reg 0x10: [mem 0xefffd000-0xefffdfff]
[ 0.391319] pci 0000:00:0f.5: PME# supported from D0 D3hot D3cold
[ 0.391592] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 0.391862] PCI: pci_cache_line_size set to 32 bytes
[ 0.392876] amd_nb: Cannot enumerate AMD northbridges
[ 0.400034] clocksource: Switched to clocksource pit
[ 0.412023] pci_bus 0000:00: resource 4 [io 0x0000-0xffff]
[ 0.412047] pci_bus 0000:00: resource 5 [mem 0x00000000-0xffffffff]
[ 0.412170] NET: Registered protocol family 2
[ 0.426222] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.437214] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.446358] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.455526] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.463099] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.472102] NET: Registered protocol family 1
[ 0.485502] PCI: CLS 32 bytes, default 32
[ 0.496841] platform rtc_cmos: registered platform RTC device (no PNP device found)
[ 0.513348] alix: system is recognized as "PC Engines ALIX.2 v0.99h"
[ 0.522682] NatSemi SCx200 Driver
[ 0.533434] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.567375] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.577231] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.589524] io scheduler noop registered
[ 0.591373] io scheduler deadline registered (default)
[ 0.607202] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.616521] serial8250: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 921600) is a NS16550A
[ 0.630654] serial8250: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 921600) is a NS16550A
[ 0.638049] Non-volatile memory driver v1.3
[ 0.650792] AMD Geode RNG detected
[ 0.661214] platform pc8736x_gpio.0: NatSemi pc8736x GPIO Driver Initializing
[ 0.672692] platform pc8736x_gpio.0: no device found
[ 0.687689] nsc_gpio initializing
[ 0.699709] loop: module loaded
[ 0.709624] cs5535-gpio cs5535-gpio: reserved resource region [io 0x6100-0x61ff]
[ 0.712441] cs5535-mfgpt cs5535-mfgpt: reserved resource region [io 0x6200-0x623f]
[ 0.725518] cs5535-mfgpt cs5535-mfgpt: 8 MFGPT timers available
[ 0.733554] cs5535-mfd 0000:00:0f.0: 5 devices registered.
[ 0.754393] scsi host0: pata_cs5536
[ 0.765965] scsi host1: pata_cs5536
[ 0.776805] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xff00 irq 14
[ 0.787746] ata2: DUMMY
[ 0.795765] via_rhine: v1.10-LK1.5.1 2010-10-09 Written by Donald Becker
[ 0.812088] via-rhine 0000:00:09.0 eth0: VIA Rhine III (Management Adapter) at 0xd0808000, 00:0d:b9:26:98:34, IRQ 10
[ 0.824520] via-rhine 0000:00:09.0 eth0: MII PHY found at address 1, status 0x7849 advertising 05e1 Link 0000
[ 0.840478] via-rhine 0000:00:0b.0 eth1: VIA Rhine III (Management Adapter) at 0xd080a000, 00:0d:b9:26:98:35, IRQ 15
[ 0.842908] via-rhine 0000:00:0b.0 eth1: MII PHY found at address 1, status 0x7849 advertising 05e1 Link 0000
[ 0.852873] Fusion MPT base driver 3.04.20
[ 0.865231] Copyright © 1999-2008 LSI Corporation
[ 0.879942] Fusion MPT SPI Host driver 3.04.20
[ 0.883426] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.893066] ehci-pci: EHCI PCI platform driver
[ 0.906616] ehci-pci 0000:00:0f.5: EHCI Host Controller
[ 0.912396] ehci-pci 0000:00:0f.5: new USB bus registered, assigned bus number 1
[ 0.924818] ehci-pci 0000:00:0f.5: irq 12, io mem 0xefffd000
[ 0.951226] ehci-pci 0000:00:0f.5: USB 2.0 started, EHCI 1.00
[ 0.969459] hub 1-0:1.0: USB hub found
[ 0.980963] hub 1-0:1.0: 4 ports detected
[ 0.983635] ehci-platform: EHCI generic platform driver
[ 0.999446] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.008075] ohci-pci: OHCI PCI platform driver
[ 1.011597] ohci-pci 0000:00:0f.4: OHCI PCI host controller
[ 1.028400] ohci-pci 0000:00:0f.4: new USB bus registered, assigned bus number 2
[ 1.040750] ohci-pci 0000:00:0f.4: irq 12, io mem 0xefffe000
[ 1.134663] hub 2-0:1.0: USB hub found
[ 1.146187] hub 2-0:1.0: 4 ports detected
[ 1.158660] ata1.00: CFA: LEXAR ATA FLASH CARD, 20131216, max UDMA7
[ 1.167536] ata1.00: 31260096 sectors, multi 0: LBA48
[ 1.173038] ata1.00: limited to UDMA/33 due to 40-wire cable
[ 1.190908] ohci-platform: OHCI generic platform driver
[ 1.218557] i8042: No controller found
[ 1.230301] rtc_cmos rtc_cmos: rtc core: registered rtc_cmos as rtc0
[ 1.239475] rtc_cmos rtc_cmos: alarms up to one day, 114 bytes nvram
[ 1.248819] cs5535-smb cs5535-smb: SCx200 device 'CS5535 ACB0' registered
[ 1.265748] cs5535-mfgpt cs5535-mfgpt: registered timer 0
[ 1.272169] sc1200wdt: build 20020303
[ 1.283224] sc1200wdt: io parameter must be specified
[ 1.299103] dmi-sysfs: dmi entry is absent.
[ 1.301727] cs5535-mfgpt cs5535-mfgpt: registered timer 1
[ 1.318009] cs5535-clockevt: Registering MFGPT timer as a clock event, using IRQ 7
[ 1.332504] NET: Registered protocol family 10
[ 1.332805] ata1.00: configured for UDMA/33
[ 1.346367] scsi 0:0:0:0: Direct-Access ATA LEXAR ATA FLASH 1216 PQ: 0 ANSI: 5
[ 1.362809] sd 0:0:0:0: [sda] 31260096 512-byte logical blocks: (16.0 GB/14.9 GiB)
[ 1.365914] sd 0:0:0:0: [sda] Write Protect is off
[ 1.380471] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.380874] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 1.390418] NET: Registered protocol family 17
[ 1.393992] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 1.401983] 8021q: 802.1Q VLAN Support v1.8
[ 1.414938] Using IPI Shortcut mode
[ 1.426613] sda: sda1 sda2
[ 1.437102] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 1.443999] rtc_cmos rtc_cmos: setting system clock to 2000-01-01 00:00:15 UTC (946684815)
[ 1.462909] VFS: Mounted root (squashfs filesystem) readonly on device 8:2.
[ 1.464306] Freeing unused kernel memory: 288K (c1445000 - c148d000)
[ 1.613932] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0xe5b766acc7, max_idle_ns: 881590452993 ns
[ 1.613932] clocksource: Switched to clocksource tsc
[ 1.808717] usb 1-1: new high-speed USB device number 2 using ehci-pci
[ 2.449111] init: Console is alive
[ 2.459678] init: - watchdog -
[ 3.499149] Button Hotplug driver version 0.4.1
[ 3.527397] init: - preinit -
[ 4.310017] random: jshn: uninitialized urandom read (4 bytes read, 58 bits of entropy available)
[ 4.360133] random: jshn: uninitialized urandom read (4 bytes read, 58 bits of entropy available)
[ 4.406199] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 4.423811] 8021q: adding VLAN 0 to HW filter on device eth0
[ 5.860015] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 7.830183] random: procd: uninitialized urandom read (4 bytes read, 66 bits of entropy available)
[ 8.088045] mount_root: switching to f2fs overlay
[ 8.261784] EXT4-fs (sda1): mounted filesystem without journal. Opts: (null)
[ 8.291066] urandom-seed: Seeding with /etc/urandom.seed
[ 8.511845] procd: - early -
[ 8.523777] procd: - watchdog -
[ 9.227180] procd: - ubus -
[ 9.448878] random: ubusd: uninitialized urandom read (4 bytes read, 89 bits of entropy available)
[ 9.476995] random: ubusd: uninitialized urandom read (4 bytes read, 89 bits of entropy available)
[ 9.504279] random: ubusd: uninitialized urandom read (4 bytes read, 89 bits of entropy available)
[ 9.531276] random: ubusd: uninitialized urandom read (4 bytes read, 90 bits of entropy available)
[ 9.558587] random: ubusd: uninitialized urandom read (4 bytes read, 90 bits of entropy available)
[ 9.585568] random: ubusd: uninitialized urandom read (4 bytes read, 90 bits of entropy available)
[ 9.612707] random: ubusd: uninitialized urandom read (4 bytes read, 90 bits of entropy available)
[ 9.640022] procd: - init -
[ 10.042021] Geode LX AES 0000:00:01.2: GEODE AES engine enabled.
[ 10.063375] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 10.089627] Loading modules backported from Linux version wt-2016-10-03-1-g6fcb1a6
[ 10.112448] Backport generated by backports.git backports-20160324-9-g0e38f5c
[ 10.136224] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 10.158134] nf_conntrack version 0.5.0 (3979 buckets, 15916 max)
[ 10.197175] xt_time: kernel timezone is -0000
[ 10.247005] PPP generic driver version 2.4.2
[ 10.261775] NET: Registered protocol family 24
[ 10.303570] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested
[ 10.325541] usbcore: registered new interface driver ath9k_htc
[ 10.990025] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008
[ 11.259454] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits
[ 11.708346] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4
[ 11.724714] ath9k_htc 1-1:1.0: FW RMW support: On
[ 11.738925] ath: EEPROM regdomain: 0x60
[ 11.738936] ath: EEPROM indicates we should expect a direct regpair map
[ 11.738958] ath: Country alpha2 being used: 00
[ 11.738968] ath: Regpair used: 0x60
[ 12.053195] ieee80211 phy0: Atheros AR9271 Rev:1
[ 12.201914] random: nonblocking pool is initialized
[ 15.952779] 8021q: adding VLAN 0 to HW filter on device eth0
[ 15.995166] device eth0 entered promiscuous mode
[ 16.020115] br-lan: port 1(eth0) entered forwarding state
[ 16.036463] br-lan: port 1(eth0) entered forwarding state
[ 16.062778] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 16.080503] 8021q: adding VLAN 0 to HW filter on device eth1
[ 18.034508] br-lan: port 1(eth0) entered forwarding state
root@LEDE:~#

Rob White commented on 15.02.2017 14:10

@Jo-Phillipp
The problem is I used sysupgrade to reflash from OpenWrt CC.

I have worked round this by removing the CF card and mounting on my laptop where I deleted existing partitions then flashed the image using DD. It now works perfectly as far as I can see so far.

Is this issue likely to be unique to the x86 image?

The next item on my list is to try a Ubiquiti AirGateway where the only options are sysupgrade or tftp.

Rob White commented on 24.07.2017 07:50

@Jo-Philipp Wich
I revisited this with:
lede-17.01.2-x86-geode-combined-squashfs.img
and then with:
lede-17.01.2-x86-geode-rootfs-ext4.img.gz

I can confirm this is a very definite problem with the squashfs image in that it uses f2fs rather than jffs2 for the overlay and any changes to files are NOT committed to flash, ie revert after a reboot (although very occasionally it DOES work).

Reflashing with the ext4 image, all works as expected.

Loading...

Available keyboard shortcuts

Tasklist

Task Details

Task Editing