New issue
Have a question about this project? Sign up for a free GitHub account to open an issue and contact its maintainers and the community.
By clicking “Sign up for GitHub”, you agree to our terms of service and privacy statement. We’ll occasionally send you account related emails.
Already on GitHub? Sign in to your account
FS#4229 - MT7621 Wireless default error #9211
Comments
nicefile: please post output from command |
jackadam:
Wiphy phy1
wiphy index: 1
max # scan SSIDs: 4
max scan IEs length: 543 bytes
max # sched scan SSIDs: 10
max # match sets: 16
Retry short limit: 7
Retry long limit: 4
Coverage class: 0 (up to 0m)
Device supports AP-side u-APSD.
Device supports T-DLS.
Available Antennas: TX 0x3 RX 0x3
Configured Antennas: TX 0x3 RX 0x3
Supported interface modes:
* IBSS
* managed
* AP
* AP/VLAN
* monitor
* mesh point
* P2P-client
* P2P-GO
Band 2:
Capabilities: 0x1ff
RX LDPC
HT20/HT40
SM Power Save disabled
RX Greenfield
RX HT20 SGI
RX HT40 SGI
TX STBC
RX STBC 1-stream
Max AMSDU length: 3839 bytes
No DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: No restriction (0x00)
HT TX/RX MCS rate indexes supported: 0-15
VHT Capabilities (0x338001b0):
Max MPDU length: 3895
Supported Channel Width: neither 160 nor 80+80
RX LDPC
short GI (80 MHz)
TX STBC
RX antenna pattern consistency
TX antenna pattern consistency
VHT RX MCS set:
1 streams: MCS 0-9
2 streams: MCS 0-9
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
VHT RX highest supported: 0 Mbps
VHT TX MCS set:
1 streams: MCS 0-9
2 streams: MCS 0-9
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
VHT TX highest supported: 0 Mbps
Frequencies:
* 5180 MHz [36] (9.0 dBm)
* 5200 MHz [40] (9.0 dBm)
* 5220 MHz [44] (9.0 dBm)
* 5240 MHz [48] (9.0 dBm)
* 5260 MHz [52] (9.0 dBm) (no IR, radar detection)
* 5280 MHz [56] (9.0 dBm) (no IR, radar detection)
* 5300 MHz [60] (9.0 dBm) (no IR, radar detection)
* 5320 MHz [64] (9.0 dBm) (no IR, radar detection)
* 5500 MHz [100] (9.0 dBm) (no IR, radar detection)
* 5520 MHz [104] (9.0 dBm) (no IR, radar detection)
* 5540 MHz [108] (9.0 dBm) (no IR, radar detection)
* 5560 MHz [112] (9.0 dBm) (no IR, radar detection)
* 5580 MHz [116] (9.0 dBm) (no IR, radar detection)
* 5600 MHz [120] (9.0 dBm) (no IR, radar detection)
* 5620 MHz [124] (9.0 dBm) (no IR, radar detection)
* 5640 MHz [128] (9.0 dBm) (no IR, radar detection)
* 5660 MHz [132] (9.0 dBm) (no IR, radar detection)
* 5680 MHz [136] (9.0 dBm) (no IR, radar detection)
* 5700 MHz [140] (9.0 dBm) (no IR, radar detection)
* 5720 MHz [144] (9.0 dBm) (no IR, radar detection)
* 5745 MHz [149] (9.0 dBm) (no IR)
* 5765 MHz [153] (9.0 dBm) (no IR)
* 5785 MHz [157] (9.0 dBm) (no IR)
* 5805 MHz [161] (9.0 dBm) (no IR)
* 5825 MHz [165] (9.0 dBm) (no IR)
* 5845 MHz [169] (disabled)
* 5865 MHz [173] (disabled)
valid interface combinations:
* #{ IBSS } <= 1, #{ managed, AP, mesh point, P2P-client, P2P-GO } <= 16,
total <= 16, #channels <= 1, STA/AP BI must match, radar detect widths: { 20 MHz (no HT), 20 MHz, 40 MHz, 80 MHz, 80+80 MHz, 160 MHz }
|
jackadam: anyone help? |
jackadam:
Supply the following if possible:
Device problem occurs on
Software versions of OpenWrt/LEDE release, packages, etc.
Steps to reproduce
Device problem occurs on Phicomm K2P
Software versions of OpenWrt/LEDE release OpenWrt 21.02.1 r16325-88151b8303 / LuCI openwrt-21.02 branch git-21.295.67054-13df80d
Steps to reproduce just flash openwrt-21.02.1-ramips-mt7621-phicomm_k2p-squashfs-sysupgrade.bin
/etc/config/wireless
config wifi-device 'radio0'
option type 'mac80211'
option channel '36'
option hwmode '11a'
option path '1e140000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0'
option htmode 'VHT80'
option disabled '1'
config wifi-iface 'default_radio0'
option device 'radio0'
option network 'lan'
option mode 'ap'
option ssid 'OpenWrt'
option encryption 'none'
config wifi-device 'radio1'
option type 'mac80211'
option channel '36'
option hwmode '11a'
option path '1e140000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0+1'
option htmode 'VHT80'
option disabled '1'
config wifi-iface 'default_radio1'
option device 'radio1'
option network 'lan'
option mode 'ap'
option ssid 'OpenWrt'
option encryption 'none'
It's two 802.11nac,no have 802.11bg.
in luci if you enable two wifi ,they all cheange to 802.11nac.
The text was updated successfully, but these errors were encountered: