You signed in with another tab or window. Reload to refresh your session.You signed out in another tab or window. Reload to refresh your session.You switched accounts on another tab or window. Reload to refresh your session.Dismiss alert
Set radio0 (5ghz) channel to any channel that is not 40 or 153 at 80mhz width.
2a. If the manual channel selection frequency is within the 80mhz width of channels 40 or 153, radio0 will broadcast a wifi network that is actually at 40 or 153 (according to the Channel Analyzer feature).
2b. If the manual channel selection frequency is outside the above limits, radio0 will be disabled.
I am not sure if this is a hardware limitation of the R7800 or related to DFS but the tested channels should be outside the TDWR frequency range.
dmesg log with a test of the channel set outside the 80mhz width of 40 and 153 (ex: 60, 116, 144) so the radio is disabled. Then the channel is set to 40/153 and it ends up working.
[ 2897.661980] br-lan: port 3(wlan0) entered disabled state
[ 2897.664209] device wlan0 left promiscuous mode
[ 2897.666424] br-lan: port 3(wlan0) entered disabled state
[ 2903.621030] ath10k_pci 0000:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
[ 2903.621056] ath10k_pci 0000:01:00.0: msdu-desc: 2500 skid: 32
[ 2903.703062] ath10k_pci 0000:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
[ 2903.703912] ath10k_pci 0000:01:00.0: wmi print 'free: 84920 iram: 13156 sram: 11224'
[ 2904.090785] ath10k_pci 0000:01:00.0: rts threshold -1
[ 2904.091643] ath10k_pci 0000:01:00.0: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4
[ 2910.104019] ath10k_pci 0000:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
[ 2910.104045] ath10k_pci 0000:01:00.0: msdu-desc: 2500 skid: 32
[ 2910.186082] ath10k_pci 0000:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
[ 2910.186928] ath10k_pci 0000:01:00.0: wmi print 'free: 84920 iram: 13156 sram: 11224'
[ 2910.573428] ath10k_pci 0000:01:00.0: rts threshold -1
[ 2910.573700] ath10k_pci 0000:01:00.0: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4
[ 2910.579716] br-lan: port 3(wlan0) entered blocking state
[ 2910.588492] br-lan: port 3(wlan0) entered disabled state
[ 2910.594228] device wlan0 entered promiscuous mode
[ 2910.920831] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 2910.921053] br-lan: port 3(wlan0) entered blocking state
[ 2910.926269] br-lan: port 3(wlan0) entered forwarding state
The text was updated successfully, but these errors were encountered:
ansonl:
2a. If the manual channel selection frequency is within the 80mhz width of channels 40 or 153, radio0 will broadcast a wifi network that is actually at 40 or 153 (according to the Channel Analyzer feature).
2b. If the manual channel selection frequency is outside the above limits, radio0 will be disabled.
I am not sure if this is a hardware limitation of the R7800 or related to DFS but the tested channels should be outside the TDWR frequency range.
dmesg log with a test of the channel set outside the 80mhz width of 40 and 153 (ex: 60, 116, 144) so the radio is disabled. Then the channel is set to 40/153 and it ends up working.
[ 2897.661980] br-lan: port 3(wlan0) entered disabled state
[ 2897.664209] device wlan0 left promiscuous mode
[ 2897.666424] br-lan: port 3(wlan0) entered disabled state
[ 2903.621030] ath10k_pci 0000:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
[ 2903.621056] ath10k_pci 0000:01:00.0: msdu-desc: 2500 skid: 32
[ 2903.703062] ath10k_pci 0000:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
[ 2903.703912] ath10k_pci 0000:01:00.0: wmi print 'free: 84920 iram: 13156 sram: 11224'
[ 2904.090785] ath10k_pci 0000:01:00.0: rts threshold -1
[ 2904.091643] ath10k_pci 0000:01:00.0: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4
[ 2910.104019] ath10k_pci 0000:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
[ 2910.104045] ath10k_pci 0000:01:00.0: msdu-desc: 2500 skid: 32
[ 2910.186082] ath10k_pci 0000:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
[ 2910.186928] ath10k_pci 0000:01:00.0: wmi print 'free: 84920 iram: 13156 sram: 11224'
[ 2910.573428] ath10k_pci 0000:01:00.0: rts threshold -1
[ 2910.573700] ath10k_pci 0000:01:00.0: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4
[ 2910.579716] br-lan: port 3(wlan0) entered blocking state
[ 2910.588492] br-lan: port 3(wlan0) entered disabled state
[ 2910.594228] device wlan0 entered promiscuous mode
[ 2910.920831] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 2910.921053] br-lan: port 3(wlan0) entered blocking state
[ 2910.926269] br-lan: port 3(wlan0) entered forwarding state
The text was updated successfully, but these errors were encountered: