Skip to content
New issue

Have a question about this project? Sign up for a free GitHub account to open an issue and contact its maintainers and the community.

By clicking “Sign up for GitHub”, you agree to our terms of service and privacy statement. We’ll occasionally send you account related emails.

Already on GitHub? Sign in to your account

FS#4039 - MR8300 / Device is not active - Qualcomm Atheros QCA9886 802.11nac #9028

Open
openwrt-bot opened this issue Sep 14, 2021 · 4 comments
Labels

Comments

@openwrt-bot
Copy link

lejeczek:

Hi.
A novice here so please go easy on me.
I've just got OpenWrt 21.02.0 r16279-5cc0535800 on my Linksys MR8300 and one iface does not seem to work.
I followed some suggestion people share on forum, where setup of wifi+timezone+timesync is supposed to be done prior to flash to OpenWrt but that changed nothing.
Even if wlan0 is the only wifi iface/network enabled it fails to start.


Tue Sep 14 10:33:15 2021 daemon.notice hostapd: Configuration file: /var/run/hostapd-phy0.conf (phy wlan0) --> new PHY
Tue Sep 14 10:33:15 2021 daemon.info procd: - init complete -
Tue Sep 14 10:33:16 2021 daemon.err odhcpd[1028]: Failed to send to ff02::1%lan@br-lan (Address not available)
Tue Sep 14 10:33:17 2021 kern.warn kernel: [ 27.923131] ath10k_pci 0000:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
Tue Sep 14 10:33:17 2021 kern.warn kernel: [ 27.923177] ath10k_pci 0000:01:00.0: msdu-desc: 2500 skid: 32
Tue Sep 14 10:33:17 2021 kern.info kernel: [ 27.977890] ath10k_pci 0000:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
Tue Sep 14 10:33:17 2021 kern.info kernel: [ 27.979711] ath10k_pci 0000:01:00.0: wmi print 'free: 114572 iram: 12644 sram: 29508'
Tue Sep 14 10:33:18 2021 kern.info kernel: [ 28.311499] ath10k_pci 0000:01:00.0: rts threshold -1
Tue Sep 14 10:33:18 2021 kern.warn kernel: [ 28.313728] ath10k_pci 0000:01:00.0: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4
Tue Sep 14 10:33:18 2021 kern.info kernel: [ 28.326258] br-lan: port 2(wlan0) entered blocking state
Tue Sep 14 10:33:18 2021 kern.info kernel: [ 28.326583] br-lan: port 2(wlan0) entered disabled state
Tue Sep 14 10:33:18 2021 daemon.notice hostapd: Frequency 5500 (primary) not allowed for AP mode, flags: 0x301979 RADAR
Tue Sep 14 10:33:18 2021 daemon.err hostapd: Primary frequency not allowed
Tue Sep 14 10:33:18 2021 daemon.warn hostapd: wlan0: IEEE 802.11 Configured channel (100) or frequency (5500) not found from the channel list of the current mode (2) IEEE 802.11a
Tue Sep 14 10:33:18 2021 daemon.warn hostapd: wlan0: IEEE 802.11 Hardware does not support configured channel
Tue Sep 14 10:33:18 2021 daemon.err hostapd: Could not select hw_mode and channel. (-3)
Tue Sep 14 10:33:18 2021 daemon.notice hostapd: wlan0: interface state UNINITIALIZED->DISABLED
Tue Sep 14 10:33:18 2021 daemon.notice hostapd: wlan0: AP-DISABLED
Tue Sep 14 10:33:18 2021 daemon.err hostapd: wlan0: Unable to setup interface.
Tue Sep 14 10:33:18 2021 daemon.notice hostapd: nl80211: deinit ifname=wlan0 disabled_11b_rates=0
Tue Sep 14 10:33:18 2021 kern.info kernel: [ 28.332587] device wlan0 entered promiscuous mode
Tue Sep 14 10:33:18 2021 kern.info kernel: [ 28.412245] device wlan0 left promiscuous mode
Tue Sep 14 10:33:18 2021 kern.info kernel: [ 28.413594] br-lan: port 2(wlan0) entered disabled state
Tue Sep 14 10:33:18 2021 kern.warn kernel: [ 28.479885] ath10k_pci 0000:01:00.0: peer-unmap-event: unknown peer id 0
Tue Sep 14 10:33:18 2021 daemon.notice hostapd: wlan0: CTRL-EVENT-TERMINATING
Tue Sep 14 10:33:18 2021 daemon.err hostapd: hostapd_free_hapd_data: Interface wlan0 wasn't started
Tue Sep 14 10:33:18 2021 daemon.notice netifd: radio0 (1354): Command failed: Invalid argument
Tue Sep 14 10:33:18 2021 daemon.notice netifd: radio0 (1354): Device setup failed: HOSTAPD_START_FAILED

Please feel free to ask for any info you might need, I'll try to get it.

Many thanks, L.

@Djfe
Copy link
Contributor

Djfe commented Jan 23, 2023

I'm fairly sure this was fixed and can be closed
I own said device and used all radios. If you want me to do further tests, then ask.
It's a triple radio device. 5ghz is split. channels [36-64] and [100+]

@dseven
Copy link

dseven commented Jun 5, 2023

You may need to set the country code for that radio in order for channel become available.

@Djfe
Copy link
Contributor

Djfe commented Jun 5, 2023

He's not subscribed to this issue, yet. (this was reported on flyspray)
ping @lejeczek
Are you still experiencing issues?

@lejeczek
Copy link

Hi.
Not any more, now, after several software stack up-dates/grades the issue is no more.
Thanks. L.

Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment
Labels
Projects
None yet
Development

No branches or pull requests

4 participants