OpenWrt/LEDE Project

  • Status Unconfirmed
  • Percent Complete
    0%
  • Task Type Bug Report
  • Category Base system
  • Assigned To No-one
  • Operating System All
  • Severity Low
  • Priority Very Low
  • Reported Version Trunk
  • Due in Version Undecided
  • Due Date Undecided
  • Private
Attached to Project: OpenWrt/LEDE Project
Opened by lejeczek - 14.09.2021

FS#4039 - MR8300 / Device is not active - Qualcomm Atheros QCA9886 802.11nac

Hi.
A novice here so please go easy on me.
I’ve just got OpenWrt 21.02.0 r16279-5cc0535800 on my Linksys MR8300 and one iface does not seem to work.
I followed some suggestion people share on forum, where setup of wifi+timezone+timesync is supposed to be done prior to flash to OpenWrt but that changed nothing.
Even if wlan0 is the only wifi iface/network enabled it fails to start.


Tue Sep 14 10:33:15 2021 daemon.notice hostapd: Configuration file: /var/run/hostapd-phy0.conf (phy wlan0) –> new PHY
Tue Sep 14 10:33:15 2021 daemon.info procd: - init complete -
Tue Sep 14 10:33:16 2021 daemon.err odhcpd[1028]: Failed to send to ff02::1%lan@br-lan (Address not available)
Tue Sep 14 10:33:17 2021 kern.warn kernel: [ 27.923131] ath10k_pci 0000:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
Tue Sep 14 10:33:17 2021 kern.warn kernel: [ 27.923177] ath10k_pci 0000:01:00.0: msdu-desc: 2500 skid: 32
Tue Sep 14 10:33:17 2021 kern.info kernel: [ 27.977890] ath10k_pci 0000:01:00.0: wmi print ‘P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0’ Tue Sep 14 10:33:17 2021 kern.info kernel: [ 27.979711] ath10k_pci 0000:01:00.0: wmi print ‘free: 114572 iram: 12644 sram: 29508’ Tue Sep 14 10:33:18 2021 kern.info kernel: [ 28.311499] ath10k_pci 0000:01:00.0: rts threshold -1
Tue Sep 14 10:33:18 2021 kern.warn kernel: [ 28.313728] ath10k_pci 0000:01:00.0: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4
Tue Sep 14 10:33:18 2021 kern.info kernel: [ 28.326258] br-lan: port 2(wlan0) entered blocking state
Tue Sep 14 10:33:18 2021 kern.info kernel: [ 28.326583] br-lan: port 2(wlan0) entered disabled state
Tue Sep 14 10:33:18 2021 daemon.notice hostapd: Frequency 5500 (primary) not allowed for AP mode, flags: 0×301979 RADAR
Tue Sep 14 10:33:18 2021 daemon.err hostapd: Primary frequency not allowed
Tue Sep 14 10:33:18 2021 daemon.warn hostapd: wlan0: IEEE 802.11 Configured channel (100) or frequency (5500) not found from the channel list of the current mode (2) IEEE 802.11a
Tue Sep 14 10:33:18 2021 daemon.warn hostapd: wlan0: IEEE 802.11 Hardware does not support configured channel
Tue Sep 14 10:33:18 2021 daemon.err hostapd: Could not select hw_mode and channel. (-3)
Tue Sep 14 10:33:18 2021 daemon.notice hostapd: wlan0: interface state UNINITIALIZED→DISABLED
Tue Sep 14 10:33:18 2021 daemon.notice hostapd: wlan0: AP-DISABLED
Tue Sep 14 10:33:18 2021 daemon.err hostapd: wlan0: Unable to setup interface.
Tue Sep 14 10:33:18 2021 daemon.notice hostapd: nl80211: deinit ifname=wlan0 disabled_11b_rates=0
Tue Sep 14 10:33:18 2021 kern.info kernel: [ 28.332587] device wlan0 entered promiscuous mode
Tue Sep 14 10:33:18 2021 kern.info kernel: [ 28.412245] device wlan0 left promiscuous mode
Tue Sep 14 10:33:18 2021 kern.info kernel: [ 28.413594] br-lan: port 2(wlan0) entered disabled state
Tue Sep 14 10:33:18 2021 kern.warn kernel: [ 28.479885] ath10k_pci 0000:01:00.0: peer-unmap-event: unknown peer id 0
Tue Sep 14 10:33:18 2021 daemon.notice hostapd: wlan0: CTRL-EVENT-TERMINATING
Tue Sep 14 10:33:18 2021 daemon.err hostapd: hostapd_free_hapd_data: Interface wlan0 wasn’t started
Tue Sep 14 10:33:18 2021 daemon.notice netifd: radio0 (1354): Command failed: Invalid argument
Tue Sep 14 10:33:18 2021 daemon.notice netifd: radio0 (1354): Device setup failed: HOSTAPD_START_FAILED


Please feel free to ask for any info you might need, I’ll try to get it.

Many thanks, L.

Loading...

Available keyboard shortcuts

Tasklist

Task Details

Task Editing