We read every piece of feedback, and take your input very seriously.
To see all available qualifiers, see our documentation.
Have a question about this project? Sign up for a free GitHub account to open an issue and contact its maintainers and the community.
By clicking “Sign up for GitHub”, you agree to our terms of service and privacy statement. We’ll occasionally send you account related emails.
Already on GitHub? Sign in to your account
cryobry:
Supply the following if possible:
Devices: Archer C7 v2, Linksys EA8300 OpenWRT: 21.02 rc4
Steps:
opkg remove ath10k-firmware-qca988x-ct && opkg install ath10k-firmware-qca988x-ct-full-htt && reboot
opkg remove ath10k-firmware-qca4019-ct && opkg install ath10k-firmware-qca4019-ct-htt && reboot
config wifi-device 'radio2' option type 'mac80211' option hwmode '11a' option path 'platform/soc/a800000.wifi' option htmode 'VHT80' option cell_density '0' option channel '36'
config wifi-iface 'wifinet6' option device 'radio2' option mode 'ap' option ssid 'ssid' option encryption 'sae' option key 'xxxxxxx' option ieee80211w '2' option wds '1' option network 'lan' 3. iwinfo and luci reports operation on channel 40: Archer: wlan0-1 ESSID: "ssid" Access Point: XX:XX:XX:XX:XX Mode: Client Channel: 40 (5.200 GHz) Center Channel 1: 42 2: unknown Tx-Power: 20 dBm Link Quality: 52/70 Signal: -58 dBm Noise: -102 dBm Bit Rate: 351.0 MBit/s Encryption: WPA3 SAE (CCMP) Type: nl80211 HW Mode(s): 802.11nac Hardware: 168C:003C 0000:0000 [Qualcomm Atheros QCA9880] TX power offset: none Frequency offset: none Supports VAPs: yes PHY name: phy0
config wifi-iface 'wifinet6' option device 'radio2' option mode 'ap' option ssid 'ssid' option encryption 'sae' option key 'xxxxxxx' option ieee80211w '2' option wds '1' option network 'lan'
EA8300: wlan2 ESSID: "ssid" Access Point: XX:XX:XX:XX:XX Mode: Master Channel: 40 (5.200 GHz) Center Channel 1: 42 2: unknown Tx-Power: 23 dBm Link Quality: 31/70 Signal: -79 dBm Noise: -105 dBm Bit Rate: 866.7 MBit/s Encryption: WPA3 SAE (CCMP) Type: nl80211 HW Mode(s): 802.11nac Hardware: 168C:003C 168C:4019 [Qualcomm Atheros IPQ4019] TX power offset: none Frequency offset: none Supports VAPs: yes PHY name: phy2
My wifi analyzers show that the signal is actually on channel 36, it is just reported incorrectly by the firmware.
The text was updated successfully, but these errors were encountered:
No branches or pull requests
cryobry:
Supply the following if possible:
Devices: Archer C7 v2, Linksys EA8300
OpenWRT: 21.02 rc4
Steps:
opkg remove ath10k-firmware-qca988x-ct && opkg install ath10k-firmware-qca988x-ct-full-htt && reboot
(EA8300) Replace default ath10k-firmware-qca4019-ct firmware with ath10k-firmware-qca4019-ct-htt
opkg remove ath10k-firmware-qca4019-ct && opkg install ath10k-firmware-qca4019-ct-htt && reboot
cat /etc/config/wireless:
config wifi-device 'radio2' option type 'mac80211' option hwmode '11a' option path 'platform/soc/a800000.wifi' option htmode 'VHT80' option cell_density '0' option channel '36'
config wifi-iface 'wifinet6'
option device 'radio2'
option mode 'ap'
option ssid 'ssid'
option encryption 'sae'
option key 'xxxxxxx'
option ieee80211w '2'
option wds '1'
option network 'lan'
3. iwinfo and luci reports operation on channel 40:
Archer:
wlan0-1 ESSID: "ssid"
Access Point: XX:XX:XX:XX:XX
Mode: Client Channel: 40 (5.200 GHz)
Center Channel 1: 42 2: unknown
Tx-Power: 20 dBm Link Quality: 52/70
Signal: -58 dBm Noise: -102 dBm
Bit Rate: 351.0 MBit/s
Encryption: WPA3 SAE (CCMP)
Type: nl80211 HW Mode(s): 802.11nac
Hardware: 168C:003C 0000:0000 [Qualcomm Atheros QCA9880]
TX power offset: none
Frequency offset: none
Supports VAPs: yes PHY name: phy0
EA8300:
wlan2 ESSID: "ssid"
Access Point: XX:XX:XX:XX:XX
Mode: Master Channel: 40 (5.200 GHz)
Center Channel 1: 42 2: unknown
Tx-Power: 23 dBm Link Quality: 31/70
Signal: -79 dBm Noise: -105 dBm
Bit Rate: 866.7 MBit/s
Encryption: WPA3 SAE (CCMP)
Type: nl80211 HW Mode(s): 802.11nac
Hardware: 168C:003C 168C:4019 [Qualcomm Atheros IPQ4019]
TX power offset: none
Frequency offset: none
Supports VAPs: yes PHY name: phy2
My wifi analyzers show that the signal is actually on channel 36, it is just reported incorrectly by the firmware.
The text was updated successfully, but these errors were encountered: