OpenWrt/LEDE Project

  • Status Unconfirmed
  • Percent Complete
    0%
  • Task Type Bug Report
  • Category Base system
  • Assigned To No-one
  • Operating System All
  • Severity Critical
  • Priority Very Low
  • Reported Version openwrt-21.02
  • Due in Version Undecided
  • Due Date Undecided
  • Private
Attached to Project: OpenWrt/LEDE Project
Opened by Raylynn Knight - 19.07.2021

FS#3938 - Akitio MyCloud Mini hangs during boot of akitio_mycloud-initramfs-uImage

Supply the following if possible:

 

The akitio_mycloud-initramfs-uImage from 21.02.0-rc3 hangs when booting on Akitio MyCloud Mini. This was also reported as an issue in the forums with 19.07 release.

Stage-1 Bootloader 五 10月 28 10:36:29 CST 2011
Attempting to set PLLA to 750MHz ...
  plla_ctrl0 : 0x0000000A
  plla_ctrl1 : 0x000F0000
  plla_ctrl2 : 0x001D01A0
  plla_ctrl3 : 0x00000017
PLLA Set

Setup memory, testing, Image 0
  Hdr len: 0x0001AC3C
  Hdr CRC: 0xB931AD17
 OK


U-Boot 1.1.2 (Oct 28 2011 - 10:44:29)

U-Boot code: 60D00000 -> 60D1AC3C  BSS: -> 60D1F2F4
RAM Configuration:
        Bank #0: 60000000 256 MB
SRAM Configuration:
        64KB at 0x50000000
NAND:256 MiB
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Setting Linux mem= boot arg value
Reading upgrade flag from NAND address 0x01ec0000 : 0
Hit any key to stop autoboot:  0 
$ tftp 64000000 uImage.mycloud
Wait GMAC to reset
Wait for PHY reset
PHY is Realtek RTL8211D
Wait for link to come up................Link up
Wait for auto-negotiation to complete
Link is 1000M
TFTP from server 192.168.50.59; our IP address is 192.168.50.100
Filename 'uImage.mycloud'.
Load address: 0x64000000
Loading: 
ARP Resend request
T invalid RARP header
################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         ##########################
done
Bytes transferred = 7120489 (6ca669 hex)
$ bootm 64000000
## Booting image at 64000000 ...
   Image Name:   ARM OpenWrt Linux-5.4.124
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    7120425 Bytes =  6.8 MB
   Load Address: 60008000
   Entry Point:  60008000
   Verifying Checksum ... OK
OK

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 5.4.124 (builder@buildhost) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r16172-2aba3e9784)) #0 SMP Sun Jun 13 22:02:19 2021
[    0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5787d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt: Machine model: Akitio MyCloud
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] cma: Reserved 64 MiB at 0x64000000
[    0.000000] percpu: Embedded 15 pages/cpu s29772 r8192 d23476 u61440
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32480
[    0.000000] Kernel command line: earlyprintk console=ttyS0,115200
[    0.000000] Bootloader command line (ignored): root=ubi0:rootfs ubi.mtd=2,512 rootfstype=ubifs console=ttyS0,115200 elevator=cfq mac_adr=0x00,0x30,0xe0,0x00,0x00,0x01 mem=256M poweroutage=yes
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 47188K/131072K available (6144K kernel code, 171K rwdata, 784K rodata, 9216K init, 214K bss, 18348K reserved, 65536K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000] rcu:     RCU event tracing is enabled.
[    0.000000] rcu:     RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=2.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] FPGA IRQ chip 0 "interrupt-controller" @ (ptrval), 32 irqs, parent IRQ: 16
[    0.000000] random: get_random_bytes called from 0xc0800b88 with crng_init=0
[    0.000020] sched_clock: 24 bits at 390kHz, resolution 2560ns, wraps every 21474835200ns
[    0.000074] clocksource: oxnas_rps_clocksource_timer: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 19112603332 ns
[    0.000089] timer_oxnas_rps: Registered clocksource rate 390625Hz
[    0.000112] timer_oxnas_rps: Registered clock event rate 6250000Hz prescaler 0 period 62500
[    0.000276] GIC: PPI13 is secure or misconfigured
[    0.000330] GIC: PPI13 is secure or misconfigured
[    0.000450] Calibrating delay loop... 298.59 BogoMIPS (lpj=1492992)
[    0.070307] pid_max: default: 32768 minimum: 301
[    0.070661] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.070689] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.072107] CPU: Testing write buffer coherency: ok
[    0.074155] Setting up static identity map for 0x60100000 - 0x6010005c
[    0.074457] rcu: Hierarchical SRCU implementation.
[    0.075202] smp: Bringing up secondary CPUs ...
[    0.076308] GIC: PPI13 is secure or misconfigured
[    0.140692] smp: Brought up 1 node, 2 CPUs
[    0.140728] SMP: Total of 2 processors activated (598.42 BogoMIPS).
[    0.146245] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.146286] futex hash table entries: 512 (order: 2, 16384 bytes, linear)
[    0.153093] pinctrl core: initialized pinctrl subsystem
[    0.154055] NET: Registered protocol family 16
[    0.158021] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.160611] cpuidle: using governor menu
[    0.160719] No ATAGs?
[    0.181959] pps_core: LinuxPPS API ver. 1 registered
[    0.181982] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.182041] PTP clock support registered
[    0.182300] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512
[    0.183626] clocksource: Switched to clocksource oxnas_rps_clocksource_timer
[    0.185013] thermal_sys: Registered thermal governor 'step_wise'
[    0.185392] NET: Registered protocol family 2
[    0.185592] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
[    0.187010] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[    0.187092] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.187130] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear)
[    0.187169] TCP: Hash tables configured (established 1024 bind 1024)
[    0.187343] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.187412] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.187837] NET: Registered protocol family 1
[    0.187896] PCI: CLS 0 bytes, default 32
[    0.487014] workingset: timestamp_bits=14 max_order=15 bucket_order=1
[    0.498406] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.499348] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
[    0.502737] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.506877] printk: console [ttyS0] disabled
[    0.507051] 44200000.serial: ttyS0 at MMIO 0x44200000 (irq = 55, base_baud = 390625) is a 16550A
[    0.967037] printk: console [ttyS0] enabled
[    0.989649] brd: module loaded
[    1.004014] loop: module loaded
[    1.073950] Could not find a valid ONFI parameter page, trying bit-wise majority to recover it
[    1.082611] ONFI parameter recovery failed, aborting
[    1.087621] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xda
[    1.093977] nand: Hynix NAND 256MiB 3,3V 8-bit
[    1.098403] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    1.105996] Scanning device for bad blocks
[    1.161538] Bad eraseblock 618 at 0x000004d40000
[    1.183211] Bad eraseblock 824 at 0x000006700000
[    1.190617] Bad eraseblock 858 at 0x000006b40000
[    1.251353] Bad eraseblock 1536 at 0x00000c000000
[    1.271260] Bad eraseblock 1720 at 0x00000d700000
[    1.295429] Bad eraseblock 1955 at 0x00000f460000
[    1.307783] 2 fixed-partitions partitions found on MTD device 41000000.nand-controller
[    1.315706] Creating 2 MTD partitions on "41000000.nand-controller":
[    1.322055] 0x000000000000-0x0000026c0000 : "boot"
[    1.328936] 0x0000026c0000-0x000010000000 : "ubi"
[    1.337172] libphy: Fixed MDIO Bus: probed
[    1.342082] oxnas-dwmac 40400000.ethernet: IRQ eth_lpi not found
[    1.348318] oxnas-dwmac 40400000.ethernet: PTP uses main clock
[    1.354201] oxnas-dwmac 40400000.ethernet: no reset control found
[    1.424023] oxnas-dwmac 40400000.ethernet: User ID: 0x12, Synopsys ID: 0x35
[    1.430981] oxnas-dwmac 40400000.ethernet:   DWMAC1000
[    1.436070] oxnas-dwmac 40400000.ethernet: DMA HW capability register supported
[    1.443345] oxnas-dwmac 40400000.ethernet: RX Checksum Offload Engine supported
[    1.450659] oxnas-dwmac 40400000.ethernet: COE Type 2
[    1.455723] oxnas-dwmac 40400000.ethernet: TX Checksum insertion supported
[    1.462563] oxnas-dwmac 40400000.ethernet: Wake-Up On Lan supported
[    1.468899] oxnas-dwmac 40400000.ethernet: Enhanced/Alternate descriptors
[    1.475706] oxnas-dwmac 40400000.ethernet: Enabled extended descriptors
[    1.482291] oxnas-dwmac 40400000.ethernet: Ring mode enabled
[    1.487953] oxnas-dwmac 40400000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[    1.495815] oxnas-dwmac 40400000.ethernet: device MAC address 3e:c3:3f:d1:0c:ca
[    1.536033] libphy: stmmac: probed
[    1.539445] RTL8211DN Gigabit Ethernet stmmac-0:00: attached PHY driver [RTL8211DN Gigabit Ethernet] (mii_bus:phy_addr=stmmac-0:00, irq=POLL)
[    1.552128] RTL8211DN Gigabit Ethernet stmmac-0:03: attached PHY driver [RTL8211DN Gigabit Ethernet] (mii_bus:phy_addr=stmmac-0:03, irq=POLL)
[    1.567016] ledtrig-cpu: registered to indicate activity on CPUs
[    1.573120] hidraw: raw HID events driver (C) Jiri Kosina
[    1.580288] NET: Registered protocol family 10
[    1.586462] Segment Routing with IPv6
[    1.590225] NET: Registered protocol family 17
[    1.594862] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    1.607805] 8021q: 802.1Q VLAN Support v1.8

Device hangs at this point.

Raylynn Knight commented on 20.07.2021 05:46

Additional information that might prove helpful. Booting with the image meant for the PogoPlug Series 3 will result in a console on serial port which appears to be mostly functional.

See log file:

Stage-1 Bootloader 五 10月 28 10:36:29 CST 2011
Attempting to set PLLA to 750MHz ...
  plla_ctrl0 : 0x0000000A
  plla_ctrl1 : 0x000F0000
  plla_ctrl2 : 0x001D01A0
  plla_ctrl3 : 0x00000017
PLLA Set

Setup memory, testing, Image 0
  Hdr len: 0x0001AC3C
  Hdr CRC: 0xB931AD17
 OK


U-Boot 1.1.2 (Oct 28 2011 - 10:44:29)

U-Boot code: 60D00000 -> 60D1AC3C  BSS: -> 60D1F2F4
RAM Configuration:
	Bank #0: 60000000 256 MB
SRAM Configuration:
	64KB at 0x50000000
NAND:256 MiB
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Setting Linux mem= boot arg value
Reading upgrade flag from NAND address 0x01ec0000 : 0
Hit any key to stop autoboot:  2  0 
$       tftp 64000000 uImage.pogo

Wait GMAC to reset
Wait for PHY reset
PHY is Realtek RTL8211D
Wait for link to come up................Link up
Wait for auto-negotiation to complete
Link is 1000M
TFTP from server 192.168.50.59; our IP address is 192.168.50.100
Filename 'uImage.pogo'.
Load address: 0x64000000
Loading: *
ARP Resend request
T invalid RARP header
#################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 ##########################
done
Bytes transferred = 7119914 (6ca42a hex)
$ bootm 64000000

## Booting image at 64000000 ...
   Image Name:   ARM OpenWrt Linux-5.4.124
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    7119850 Bytes =  6.8 MB
   Load Address: 60008000
   Entry Point:  60008000
   Verifying Checksum ... OK
OK

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 5.4.124 (builder@buildhost) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r16172-2aba3e9784)) #0 SMP Sun Jun 13 22:02:19 2021
[    0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5787d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt: Machine model: Cloud Engines PogoPlug Series 3
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] cma: Reserved 64 MiB at 0x64000000
[    0.000000] percpu: Embedded 15 pages/cpu s29772 r8192 d23476 u61440
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32480
[    0.000000] Kernel command line: earlyprintk console=ttyS0,115200
[    0.000000] Bootloader command line (ignored): root=ubi0:rootfs ubi.mtd=2,512 rootfstype=ubifs console=ttyS0,115200 elevator=cfq mac_adr=0x00,0x30,0xe0,0x00,0x00,0x01 mem=256M poweroutage=yes
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 47192K/131072K available (6144K kernel code, 171K rwdata, 784K rodata, 9216K init, 214K bss, 18344K reserved, 65536K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000] rcu: 	RCU event tracing is enabled.
[    0.000000] rcu: 	RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=2.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] FPGA IRQ chip 0 "interrupt-controller" @ (ptrval), 32 irqs, parent IRQ: 16
[    0.000000] random: get_random_bytes called from 0xc0800b88 with crng_init=0
[    0.000020] sched_clock: 24 bits at 390kHz, resolution 2560ns, wraps every 21474835200ns
[    0.000074] clocksource: oxnas_rps_clocksource_timer: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 19112603332 ns
[    0.000089] timer_oxnas_rps: Registered clocksource rate 390625Hz
[    0.000115] timer_oxnas_rps: Registered clock event rate 6250000Hz prescaler 0 period 62500
[    0.000276] GIC: PPI13 is secure or misconfigured
[    0.000330] GIC: PPI13 is secure or misconfigured
[    0.000440] Calibrating delay loop... 298.59 BogoMIPS (lpj=1492992)
[    0.070310] pid_max: default: 32768 minimum: 301
[    0.070653] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.070681] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.072097] CPU: Testing write buffer coherency: ok
[    0.074158] Setting up static identity map for 0x60100000 - 0x6010005c
[    0.074455] rcu: Hierarchical SRCU implementation.
[    0.075202] smp: Bringing up secondary CPUs ...
[    0.076316] GIC: PPI13 is secure or misconfigured
[    0.140692] smp: Brought up 1 node, 2 CPUs
[    0.140728] SMP: Total of 2 processors activated (598.42 BogoMIPS).
[    0.145999] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.146037] futex hash table entries: 512 (order: 2, 16384 bytes, linear)
[    0.152826] pinctrl core: initialized pinctrl subsystem
[    0.153781] NET: Registered protocol family 16
[    0.157747] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.160422] cpuidle: using governor menu
[    0.160529] No ATAGs?
[    0.180323] pps_core: LinuxPPS API ver. 1 registered
[    0.180444] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.180495] PTP clock support registered
[    0.180753] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512
[    0.181972] clocksource: Switched to clocksource oxnas_rps_clocksource_timer
[    0.183464] thermal_sys: Registered thermal governor 'step_wise'
[    0.183823] NET: Registered protocol family 2
[    0.184025] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
[    0.185047] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[    0.185123] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.185159] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear)
[    0.185198] TCP: Hash tables configured (established 1024 bind 1024)
[    0.185377] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.185433] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.185858] NET: Registered protocol family 1
[    0.185917] PCI: CLS 0 bytes, default 32
[    0.487029] workingset: timestamp_bits=14 max_order=15 bucket_order=1
[    0.498672] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.499584] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
[    0.502679] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.506869] printk: console [ttyS0] disabled
[    0.507064] 44200000.serial: ttyS0 at MMIO 0x44200000 (irq = 55, base_baud = 390625) is a 16550A
[    0.968360] printk: console [ttyS0] enabled
[    0.990784] brd: module loaded
[    1.005381] loop: module loaded
[    1.072320] Could not find a valid ONFI parameter page, trying bit-wise majority to recover it
[    1.080980] ONFI parameter recovery failed, aborting
[    1.086000] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xda
[    1.092364] nand: Hynix NAND 256MiB 3,3V 8-bit
[    1.096793] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    1.104373] Scanning device for bad blocks
[    1.160156] Bad eraseblock 618 at 0x000004d40000
[    1.181972] Bad eraseblock 824 at 0x000006700000
[    1.189352] Bad eraseblock 858 at 0x000006b40000
[    1.250529] Bad eraseblock 1536 at 0x00000c000000
[    1.270545] Bad eraseblock 1720 at 0x00000d700000
[    1.294853] Bad eraseblock 1955 at 0x00000f460000
[    1.307276] 5 fixed-partitions partitions found on MTD device 41000000.nand-controller
[    1.315192] Creating 5 MTD partitions on "41000000.nand-controller":
[    1.321523] 0x000000000000-0x000000040000 : "stage1"
[    1.328391] 0x000000040000-0x0000003c0000 : "u-boot"
[    1.335298] 0x0000003c0000-0x000000440000 : "u-boot-env"
[    1.342533] 0x000000440000-0x000000e00000 : "kernel"
[    1.349463] 0x000000e00000-0x000008000000 : "ubi"
[    1.357079] libphy: Fixed MDIO Bus: probed
[    1.362119] oxnas-dwmac 40400000.ethernet: IRQ eth_lpi not found
[    1.368248] oxnas-dwmac 40400000.ethernet: PTP uses main clock
[    1.374144] oxnas-dwmac 40400000.ethernet: no reset control found
[    1.442388] oxnas-dwmac 40400000.ethernet: User ID: 0x12, Synopsys ID: 0x35
[    1.449344] oxnas-dwmac 40400000.ethernet: 	DWMAC1000
[    1.454443] oxnas-dwmac 40400000.ethernet: DMA HW capability register supported
[    1.461726] oxnas-dwmac 40400000.ethernet: RX Checksum Offload Engine supported
[    1.469038] oxnas-dwmac 40400000.ethernet: COE Type 2
[    1.474099] oxnas-dwmac 40400000.ethernet: TX Checksum insertion supported
[    1.480942] oxnas-dwmac 40400000.ethernet: Wake-Up On Lan supported
[    1.487272] oxnas-dwmac 40400000.ethernet: Enhanced/Alternate descriptors
[    1.494077] oxnas-dwmac 40400000.ethernet: Enabled extended descriptors
[    1.500664] oxnas-dwmac 40400000.ethernet: Ring mode enabled
[    1.506332] oxnas-dwmac 40400000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[    1.514191] oxnas-dwmac 40400000.ethernet: device MAC address 72:18:96:3a:62:cd
[    1.554593] libphy: stmmac: probed
[    1.558003] RTL8211DN Gigabit Ethernet stmmac-0:00: attached PHY driver [RTL8211DN Gigabit Ethernet] (mii_bus:phy_addr=stmmac-0:00, irq=POLL)
[    1.570708] RTL8211DN Gigabit Ethernet stmmac-0:03: attached PHY driver [RTL8211DN Gigabit Ethernet] (mii_bus:phy_addr=stmmac-0:03, irq=POLL)
[    1.585935] ledtrig-cpu: registered to indicate activity on CPUs
[    1.592140] hidraw: raw HID events driver (C) Jiri Kosina
[    1.599168] NET: Registered protocol family 10
[    1.605281] Segment Routing with IPv6
[    1.609044] NET: Registered protocol family 17
[    1.613675] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    1.626618] 8021q: 802.1Q VLAN Support v1.8
[    1.637765] UBI error: no valid UBI magic found inside mtd4
[    1.643415] hctosys: unable to open rtc device (rtc0)
[    1.662397] Freeing unused kernel memory: 9216K
[    1.682273] Run /init as init process
[    2.368478] init: Console is alive
[    2.384486] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    2.392494] Button Hotplug driver version 0.4.1
[    2.399590] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    2.413583] init: - preinit -
[    2.710494] random: jshn: uninitialized urandom read (4 bytes read)
[    2.760727] random: jshn: uninitialized urandom read (4 bytes read)
[    2.798676] random: jshn: uninitialized urandom read (4 bytes read)
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    5.950781] procd: - early -
[    6.515496] procd: - ubus -
[    6.532293] urandom_read: 1 callbacks suppressed
[    6.532308] random: ubusd: uninitialized urandom read (4 bytes read)
[    6.569515] random: ubusd: uninitialized urandom read (4 bytes read)
[    6.576698] random: ubusd: uninitialized urandom read (4 bytes read)
[    6.587077] procd: - init -
Please press Enter to activate this console.
[    7.259412] urngd: v1.0.2 started.
[    7.368642] kmodloader: loading kernel modules from /etc/modules.d/*
[    7.418910] xt_time: kernel timezone is -0000
[    7.449802] kmodloader: done loading kernel modules from /etc/modules.d/*
[    7.469314] random: crng init done
[    7.472834] random: 3 urandom warning(s) missed due to ratelimiting
[   30.119838] oxnas-dwmac 40400000.ethernet eth0: PHY [stmmac-0:00] driver [RTL8211DN Gigabit Ethernet]
[   30.138562] oxnas-dwmac 40400000.ethernet eth0: No Safety Features support found
[   30.146078] oxnas-dwmac 40400000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[   30.154816] oxnas-dwmac 40400000.ethernet eth0: registered PTP clock
[   30.161159] oxnas-dwmac 40400000.ethernet eth0: configuring for phy/rgmii link mode
[   30.201400] br-lan: port 1(eth0) entered blocking state
[   30.206740] br-lan: port 1(eth0) entered disabled state
[   30.212520] device eth0 entered promiscuous mode
[   30.235048] br-lan: port 1(eth0) entered blocking state
[   30.240271] br-lan: port 1(eth0) entered forwarding state
[   31.195811] br-lan: port 1(eth0) entered disabled state
[   35.432593] oxnas-dwmac 40400000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[   35.441044] br-lan: port 1(eth0) entered blocking state
[   35.446336] br-lan: port 1(eth0) entered forwarding state
[   35.452820] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready



BusyBox v1.33.1 (2021-06-13 22:02:19 UTC) built-in shell (ash)

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 -----------------------------------------------------
 OpenWrt 21.02.0-rc3, r16172-2aba3e9784
 -----------------------------------------------------
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------
root@OpenWrt:/# 

Loading...

Available keyboard shortcuts

Tasklist

Task Details

Task Editing