OpenWrt/LEDE Project

  • Status Unconfirmed
  • Percent Complete
    0%
  • Task Type Bug Report
  • Category Base system
  • Assigned To No-one
  • Operating System All
  • Severity Low
  • Priority Very Low
  • Reported Version Trunk
  • Due in Version Undecided
  • Due Date Undecided
  • Private
Attached to Project: OpenWrt/LEDE Project
Opened by Kurt Roeckx - 18.02.2021

FS#3632 - EX6150 doesn't have 2.4 GHz wlan interface

I upgraded from 19.07 to a 21.02 snapshot on one my Netgear EX6150 APs. In 19.07 everything was working, but in 21.02 wlan1 doesn’t show up, and so 2.4 GHz doesn’t work.

The snapshot I’ve used was r15819-0011c7ad12

I have a wlan0 device, but there does not seem to be a wlan1 device.

The error message I see is: “radio1 (1754): Could not find PHY for device ‘radio1’”

The kernel log has:

[    0.000000] Linux version 5.4.98 (builder@buildhost) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r15819-0011c7ad12)) #0 SMP Wed Feb 17 23:14:51 2021
[    0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[    0.000000] printk: bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[    0.000000] MIPS: machine is Netgear EX6150
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] VPE topology {2} total 2
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000]   HighMem  empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] On node 0 totalpages: 16384
[    0.000000]   Normal zone: 144 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 16384 pages, LIFO batch:3
[    0.000000] percpu: Embedded 14 pages/cpu s26768 r8192 d22384 u57344
[    0.000000] pcpu-alloc: s26768 r8192 d22384 u57344 alloc=14*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 16240
[    0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes, linear)
[    0.000000] Writing ErrCtl register=00002050
[    0.000000] Readback ErrCtl register=00002050
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 56224K/65536K available (6051K kernel code, 209K rwdata, 740K rodata, 1244K init, 238K bss, 9312K reserved, 0K cma-reserved, 0K highmem)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000] rcu: 	RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS: 256
[    0.000000] random: get_random_bytes called from 0x806d9a10 with crng_init=0
[    0.000000] CPU Clock: 880MHz
[    0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns
[    0.000009] sched_clock: 32 bits at 440MHz, resolution 2ns, wraps every 4880645118ns
[    0.015489] Calibrating delay loop... 583.68 BogoMIPS (lpj=1167360)
[    0.055791] pid_max: default: 32768 minimum: 301
[    0.065118] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.079517] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.097353] rcu: Hierarchical SRCU implementation.
[    0.107312] smp: Bringing up secondary CPUs ...
[    0.117465] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.117474] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.117486] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    0.117590] CPU1 revision is: 0001992f (MIPS 1004Kc)
[    0.144374] Synchronize counters for CPU 1: done.
[    0.204026] smp: Brought up 1 node, 2 CPUs
[    0.216792] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.236085] futex hash table entries: 512 (order: 2, 16384 bytes, linear)
[    0.249705] pinctrl core: initialized pinctrl subsystem
[    0.261814] NET: Registered protocol family 16
[    0.279196] FPU Affinity set after 4688 emulations
[    0.300838] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512
[    0.322911] clocksource: Switched to clocksource GIC
[    0.334615] NET: Registered protocol family 2
[    0.344432] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[    0.361065] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.376194] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear)
[    0.390183] TCP: Hash tables configured (established 1024 bind 1024)
[    0.402957] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.415862] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.429924] NET: Registered protocol family 1
[    0.438491] PCI: CLS 0 bytes, default 32
[    0.534813] 4 CPUs re-calibrate udelay(lpj = 1163264)
[    0.546642] workingset: timestamp_bits=14 max_order=14 bucket_order=0
[    0.573876] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.585394] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.608808] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[    0.625542] mt7621_gpio 1e000600.gpio: registering 32 gpios
[    0.636943] mt7621_gpio 1e000600.gpio: registering 32 gpios
[    0.648266] mt7621_gpio 1e000600.gpio: registering 32 gpios
[    0.660204] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.677184] printk: console [ttyS0] disabled
[    0.685678] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 15, base_baud = 3125000) is a 16550A
[    0.703595] printk: console [ttyS0] enabled
[    0.720139] printk: bootconsole [early0] disabled
[    0.742677] spi-mt7621 1e000b00.spi: sys_freq: 220000000
[    0.754516] spi-nor spi0.0: mx25l12805d (16384 Kbytes)
[    0.764930] 16 fixed-partitions partitions found on MTD device spi0.0
[    0.777767] Creating 16 MTD partitions on "spi0.0":
[    0.787502] 0x000000000000-0x000000030000 : "u-boot"
[    0.799091] 0x000000030000-0x000000040000 : "config"
[    0.810580] 0x000000040000-0x000000050000 : "factory"
[    0.822248] 0x000000050000-0x000000ed0000 : "firmware"
[    0.834274] 2 uimage-fw partitions found on MTD device firmware
[    0.846110] Creating 2 MTD partitions on "firmware":
[    0.856018] 0x000000000000-0x000000240ded : "kernel"
[    0.867566] 0x000000240ded-0x000000e80000 : "rootfs"
[    0.879046] mtd: device 5 (rootfs) set to be root filesystem
[    0.890474] 1 squashfs-split partitions found on MTD device rootfs
[    0.902839] 0x000000540000-0x000000e80000 : "rootfs_data"
[    0.915265] 0x000000ed0000-0x000000ee0000 : "ML1"
[    0.926261] 0x000000ef0000-0x000000f10000 : "ML2"
[    0.937236] 0x000000f10000-0x000000f30000 : "ML3"
[    0.948332] 0x000000f30000-0x000000f50000 : "ML4"
[    0.959429] 0x000000f50000-0x000000f70000 : "ML5"
[    0.970466] 0x000000f70000-0x000000f90000 : "ML6"
[    0.981469] 0x000000f90000-0x000000fb0000 : "ML7"
[    0.992470] 0x000000fb0000-0x000000fc0000 : "T_Meter1"
[    1.004399] 0x000000fc0000-0x000000fd0000 : "T_Meter2"
[    1.016356] 0x000000fd0000-0x000000fe0000 : "POT"
[    1.027472] 0x000000fe0000-0x000000ff0000 : "board_data"
[    1.039748] 0x000000ff0000-0x000001000000 : "nvram"
[    1.052253] libphy: Fixed MDIO Bus: probed
[    1.085297] libphy: mdio: probed
[    1.091933] random: fast init done
[    1.092026] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
[    1.114888] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 17
[    1.133852] mt7621-pci 1e140000.pcie: Parsing DT failed
[    1.147634] NET: Registered protocol family 10
[    1.157945] Segment Routing with IPv6
[    1.165408] NET: Registered protocol family 17
[    1.174345] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    1.200432] 8021q: 802.1Q VLAN Support v1.8
[    1.211649] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
[    1.231871] libphy: dsa slave smi: probed
[    1.240360] mt7530 mdio-bus:1f lan (uninitialized): PHY [dsa-0.0:00] driver [Generic PHY]
[    1.259178] mt7530 mdio-bus:1f: configuring for fixed/rgmii link mode
[    1.276829] DSA: tree 0 setup
[    1.283149] rt2880-pinmux pinctrl: pcie is already enabled
[    1.294108] mt7621-pci 1e140000.pcie: Error applying setting, reverse things back
[    1.309171] mt7621-pci-phy 1e149000.pcie-phy: PHY for 0xbe149000 (dual port = 1)
[    1.324121] mt7621-pci-phy 1e14a000.pcie-phy: PHY for 0xbe14a000 (dual port = 0)
[    1.438727] mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz
[    1.449849] mt7621-pci-phy 1e14a000.pcie-phy: Xtal is 40MHz
[    1.560764] mt7621-pci 1e140000.pcie: pcie1 no card, disable it (RST & CLK)
[    1.574646] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK)
[    1.588526] mt7621-pci 1e140000.pcie: PCIE0 enabled
[    1.598251] mt7621-pci 1e140000.pcie: PCI coherence region base: 0x60000000, mask/settings: 0xf0000002
[    1.616989] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00
[    1.629676] pci_bus 0000:00: root bus resource [io  0x1e160000-0x1e16ffff]
[    1.643385] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[    1.657090] pci_bus 0000:00: root bus resource [bus 00-ff]
[    1.668068] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400
[    1.680083] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[    1.692582] pci 0000:00:00.0: reg 0x14: [mem 0x60200000-0x6020ffff]
[    1.705145] pci 0000:00:00.0: supports D1
[    1.713139] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[    1.726367] pci 0000:01:00.0: [14c3:7662] type 00 class 0x028000
[    1.738422] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit]
[    1.751996] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[    1.765456] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[    1.779165] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[    1.789590] pci 0000:00:00.0:   bridge window [io  0x0000-0x0fff]
[    1.801739] pci 0000:00:00.0:   bridge window [mem 0x60000000-0x600fffff]
[    1.815276] pci 0000:00:00.0:   bridge window [mem 0x60100000-0x601fffff pref]
[    1.829673] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[    1.842903] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[    1.856087] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[    1.869967] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[    1.883513] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x601fffff pref]
[    1.897911] pci 0000:00:00.0: BAR 1: assigned [mem 0x60200000-0x6020ffff]
[    1.911453] pci 0000:00:00.0: BAR 7: assigned [io  0x1e160000-0x1e160fff]
[    1.924993] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit]
[    1.939578] pci 0000:01:00.0: BAR 6: assigned [mem 0x60100000-0x6010ffff pref]
[    1.953972] pci 0000:00:00.0: PCI bridge to [bus 01]
[    1.963875] pci 0000:00:00.0:   bridge window [io  0x1e160000-0x1e160fff]
[    1.977411] pci 0000:00:00.0:   bridge window [mem 0x60000000-0x600fffff]
[    1.990954] pci 0000:00:00.0:   bridge window [mem 0x60100000-0x601fffff pref]
[    2.006080] hctosys: unable to open rtc device (rtc0)
[    2.016914] mt7530 mdio-bus:1f: Link is Up - 1Gbps/Full - flow control off
[    2.038208] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[    2.056945] Freeing unused kernel memory: 1244K
[    2.065997] This architecture does not have kernel memory protection.
[    2.078845] Run /sbin/init as init process
[    2.988502] init: Console is alive
[    2.995628] init: - watchdog -
[    3.959478] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    4.118297] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    4.143194] init: - preinit -
[    5.164070] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
[    5.180209] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[    5.197095] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[    5.371440] random: jshn: uninitialized urandom read (4 bytes read)
[    5.442450] random: jshn: uninitialized urandom read (4 bytes read)
[    5.477416] random: jshn: uninitialized urandom read (4 bytes read)
[    5.682283] mt7530 mdio-bus:1f lan: configuring for phy/gmii link mode
[    5.695715] 8021q: adding VLAN 0 to HW filter on device lan
[    9.811485] mt7530 mdio-bus:1f lan: Link is Up - 1Gbps/Full - flow control rx/tx
[    9.826371] IPv6: ADDRCONF(NETDEV_CHANGE): lan: link becomes ready
[   10.039229] jffs2: notice: (610) jffs2_build_xattr_subsystem: complete building xattr subsystem, 23 of xdatum (20 unchecked, 3 orphan) and 28 of xref (2 dead, 1 orphan) found.
[   10.074495] mount_root: switching to jffs2 overlay
[   10.121696] overlayfs: upper fs does not support tmpfile.
[   10.150849] urandom-seed: Seeding with /etc/urandom.seed
[   10.318734] mt7530 mdio-bus:1f lan: Link is Down
[   10.342081] procd: - early -
[   10.348026] procd: - watchdog -
[   10.982974] procd: - watchdog -
[   10.991612] procd: - ubus -
[   11.158663] procd: - init -
[   11.870555] kmodloader: loading kernel modules from /etc/modules.d/*
[   12.016884] Loading modules backported from Linux version v5.10.16-0-gde53befa79cf
[   12.032067] Backport generated by backports.git v5.10.16-1-0-g21d2a1d2
[   12.096550] xt_time: kernel timezone is -0000
[   12.121424] urngd: v1.0.2 started.
[   12.172378] mt7621-pci 1e140000.pcie: bus=1 slot=0 irq=19
[   12.183255] pci 0000:00:00.0: enabling device (0006 -> 0007)
[   12.194547] mt76x2e 0000:01:00.0: enabling device (0000 -> 0002)
[   12.206832] mt76x2e 0000:01:00.0: ASIC revision: 76120044
[   12.298002] random: crng init done
[   12.304814] random: 7 urandom warning(s) missed due to ratelimiting
[   12.619731] mt76x2e 0000:01:00.0: ROM patch build: 20141115060606a
[   12.637392] mt76x2e 0000:01:00.0: Firmware Version: 0.0.00
[   12.648387] mt76x2e 0000:01:00.0: Build: 1
[   12.656557] mt76x2e 0000:01:00.0: Build Time: 201507311614____
[   12.682836] mt76x2e 0000:01:00.0: Firmware running!
[   12.694929] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   12.727446] PPP generic driver version 2.4.2
[   12.741034] NET: Registered protocol family 24
[   12.782173] kmodloader: done loading kernel modules from /etc/modules.d/*
[   21.277464] mtk_soc_eth 1e100000.ethernet eth0: Link is Down
[   21.308640] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
[   21.324614] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[   21.351973] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   21.368246] mt7530 mdio-bus:1f lan: configuring for phy/gmii link mode
[   21.382141] 8021q: adding VLAN 0 to HW filter on device lan
[   21.398132] br-lan: port 1(lan) entered blocking state
[   21.408690] br-lan: port 1(lan) entered disabled state
[   21.421978] device lan entered promiscuous mode
[   21.431117] device eth0 entered promiscuous mode
[   24.529347] br-lan: port 2(wlan0) entered blocking state
[   24.540029] br-lan: port 2(wlan0) entered disabled state
[   24.551231] device wlan0 entered promiscuous mode
[   25.491345] mt7530 mdio-bus:1f lan: Link is Up - 1Gbps/Full - flow control rx/tx
[   25.506163] br-lan: port 1(lan) entered blocking state
[   25.516456] br-lan: port 1(lan) entered forwarding state
[   25.528015] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[  106.508897] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[  106.521813] br-lan: port 2(wlan0) entered blocking state
[  106.532497] br-lan: port 2(wlan0) entered forwarding state

The system log also shows:

netifd: Interface 'lan' is enabled
netifd: Interface 'lan' is setting up now
netifd: Interface 'lan' is now up
netifd: Interface 'loopback' is enabled
netifd: Interface 'loopback' is setting up now
netifd: Interface 'loopback' is now up
netifd: Network device 'eth0' link is up
netifd: Network device 'lo' link is up
netifd: Interface 'loopback' has link connectivity
netifd: radio1 (1754): Could not find PHY for device 'radio1'
netifd: radio1 (1879): WARNING: Variable 'data' does not exist or is not an array/object
procd: - init complete -
hostapd: Configuration file: /var/run/hostapd-phy0.conf (phy wlan0) --> new PHY

“iw dev” shows:

phy#0
	Interface wlan0
		ifindex 6
		wdev 0x2
		addr XX:XX:XX:XX:XX:XX
		ssid XXXX
		type AP
		channel 100 (5500 MHz), width: 80 MHz, center1: 5530 MHz
		txpower 24.00 dBm
		multicast TXQ:
			qsz-byt	qsz-pkt	flows	drops	marks	overlmt	hashcol	tx-bytes	tx-packets
			0	0	82	0	0	0	0	14553		82
19.02.2021 : A task closure has been requested. Reason for request: Problem fixed
Kurt Roeckx commented on 18.02.2021 16:43

I went looking for other bugs, but couldn't find any open. But it looks very much like #3093 that's closed.

Kurt Roeckx commented on 18.02.2021 18:43

It seems that PCIE1 is no longer detected, possibly due to other errors before it like:
mt7621-pci 1e140000.pcie: Parsing DT failed

And:
mt7621-pci 1e140000.pcie: Error applying setting, reverse things back

Kurt Roeckx commented on 19.02.2021 21:08

The patch at https://paste.debian.net/1186150/ fixes my problem.

Kurt Roeckx commented on 19.02.2021 21:44

This is the new kernel log after the patch was applied:

[    0.000000] Linux version 5.4.98 (builder@buildhost) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r15818-c6319239d8)) #0 SMP Wed Feb 17 08:26:10 2021
[    0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[    0.000000] printk: bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[    0.000000] MIPS: machine is Netgear EX6150
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] VPE topology {2} total 2
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000]   HighMem  empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] On node 0 totalpages: 16384
[    0.000000]   Normal zone: 144 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 16384 pages, LIFO batch:3
[    0.000000] percpu: Embedded 14 pages/cpu s26768 r8192 d22384 u57344
[    0.000000] pcpu-alloc: s26768 r8192 d22384 u57344 alloc=14*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 16240
[    0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes, linear)
[    0.000000] Writing ErrCtl register=00002050
[    0.000000] Readback ErrCtl register=00002050
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 56224K/65536K available (6051K kernel code, 209K rwdata, 740K rodata, 1244K init, 238K bss, 9312K reserved, 0K cma-reserved, 0K highmem)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000] rcu: 	RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS: 256
[    0.000000] random: get_random_bytes called from 0x806d9a10 with crng_init=0
[    0.000000] CPU Clock: 880MHz
[    0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns
[    0.000009] sched_clock: 32 bits at 440MHz, resolution 2ns, wraps every 4880645118ns
[    0.015489] Calibrating delay loop... 583.68 BogoMIPS (lpj=1167360)
[    0.055791] pid_max: default: 32768 minimum: 301
[    0.065116] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.079515] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.097346] rcu: Hierarchical SRCU implementation.
[    0.107304] smp: Bringing up secondary CPUs ...
[    0.117456] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.117466] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.117477] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    0.117581] CPU1 revision is: 0001992f (MIPS 1004Kc)
[    0.144366] Synchronize counters for CPU 1: done.
[    0.204017] smp: Brought up 1 node, 2 CPUs
[    0.216787] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.236081] futex hash table entries: 512 (order: 2, 16384 bytes, linear)
[    0.249699] pinctrl core: initialized pinctrl subsystem
[    0.261806] NET: Registered protocol family 16
[    0.279235] FPU Affinity set after 4688 emulations
[    0.301308] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512
[    0.322434] clocksource: Switched to clocksource GIC
[    0.334274] NET: Registered protocol family 2
[    0.344923] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[    0.361592] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.376720] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear)
[    0.390716] TCP: Hash tables configured (established 1024 bind 1024)
[    0.403456] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.416366] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.430487] NET: Registered protocol family 1
[    0.439055] PCI: CLS 0 bytes, default 32
[    0.538335] 4 CPUs re-calibrate udelay(lpj = 1163264)
[    0.550038] workingset: timestamp_bits=14 max_order=14 bucket_order=0
[    0.576765] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.588285] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.611667] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[    0.628451] mt7621_gpio 1e000600.gpio: registering 32 gpios
[    0.639825] mt7621_gpio 1e000600.gpio: registering 32 gpios
[    0.651149] mt7621_gpio 1e000600.gpio: registering 32 gpios
[    0.663136] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.680113] printk: console [ttyS0] disabled
[    0.688603] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 15, base_baud = 3125000) is a 16550A
[    0.706520] printk: console [ttyS0] enabled
[    0.723065] printk: bootconsole [early0] disabled
[    0.745645] spi-mt7621 1e000b00.spi: sys_freq: 220000000
[    0.757509] spi-nor spi0.0: mx25l12805d (16384 Kbytes)
[    0.767928] 16 fixed-partitions partitions found on MTD device spi0.0
[    0.780766] Creating 16 MTD partitions on "spi0.0":
[    0.790500] 0x000000000000-0x000000030000 : "u-boot"
[    0.802016] 0x000000030000-0x000000040000 : "config"
[    0.813505] 0x000000040000-0x000000050000 : "factory"
[    0.825183] 0x000000050000-0x000000ed0000 : "firmware"
[    0.837267] 2 uimage-fw partitions found on MTD device firmware
[    0.849103] Creating 2 MTD partitions on "firmware":
[    0.859011] 0x000000000000-0x000000240e91 : "kernel"
[    0.870544] 0x000000240e91-0x000000e80000 : "rootfs"
[    0.881949] mtd: device 5 (rootfs) set to be root filesystem
[    0.893397] 1 squashfs-split partitions found on MTD device rootfs
[    0.905751] 0x000000540000-0x000000e80000 : "rootfs_data"
[    0.918140] 0x000000ed0000-0x000000ee0000 : "ML1"
[    0.929155] 0x000000ef0000-0x000000f10000 : "ML2"
[    0.940136] 0x000000f10000-0x000000f30000 : "ML3"
[    0.951211] 0x000000f30000-0x000000f50000 : "ML4"
[    0.962287] 0x000000f50000-0x000000f70000 : "ML5"
[    0.973314] 0x000000f70000-0x000000f90000 : "ML6"
[    0.984313] 0x000000f90000-0x000000fb0000 : "ML7"
[    0.995416] 0x000000fb0000-0x000000fc0000 : "T_Meter1"
[    1.007367] 0x000000fc0000-0x000000fd0000 : "T_Meter2"
[    1.019309] 0x000000fd0000-0x000000fe0000 : "POT"
[    1.030382] 0x000000fe0000-0x000000ff0000 : "board_data"
[    1.042711] 0x000000ff0000-0x000001000000 : "nvram"
[    1.055144] libphy: Fixed MDIO Bus: probed
[    1.064138] random: fast init done
[    1.093110] libphy: mdio: probed
[    1.099843] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
[    1.115918] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 17
[    1.134950] mt7621-pci 1e140000.pcie: Parsing DT failed
[    1.148721] NET: Registered protocol family 10
[    1.159159] Segment Routing with IPv6
[    1.166667] NET: Registered protocol family 17
[    1.175611] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    1.201673] 8021q: 802.1Q VLAN Support v1.8
[    1.212787] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
[    1.235405] libphy: dsa slave smi: probed
[    1.243879] mt7530 mdio-bus:1f lan (uninitialized): PHY [dsa-0.0:00] driver [Generic PHY]
[    1.262704] mt7530 mdio-bus:1f: configuring for fixed/rgmii link mode
[    1.280352] DSA: tree 0 setup
[    1.286676] rt2880-pinmux pinctrl: pcie is already enabled
[    1.297644] mt7621-pci 1e140000.pcie: Error applying setting, reverse things back
[    1.312708] mt7621-pci-phy 1e149000.pcie-phy: PHY for 0xbe149000 (dual port = 1)
[    1.327657] mt7621-pci-phy 1e14a000.pcie-phy: PHY for 0xbe14a000 (dual port = 0)
[    1.442268] mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz
[    1.453391] mt7621-pci-phy 1e14a000.pcie-phy: Xtal is 40MHz
[    1.564304] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK)
[    1.578179] mt7621-pci 1e140000.pcie: PCIE0 enabled
[    1.587904] mt7621-pci 1e140000.pcie: PCIE1 enabled
[    1.597639] mt7621-pci 1e140000.pcie: PCI coherence region base: 0x60000000, mask/settings: 0xf0000002
[    1.616380] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00
[    1.629066] pci_bus 0000:00: root bus resource [io  0x1e160000-0x1e16ffff]
[    1.642775] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[    1.656478] pci_bus 0000:00: root bus resource [bus 00-ff]
[    1.667456] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400
[    1.679463] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[    1.691962] pci 0000:00:00.0: reg 0x14: [mem 0x60200000-0x6020ffff]
[    1.704533] pci 0000:00:00.0: supports D1
[    1.712527] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[    1.724441] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400
[    1.736462] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[    1.748960] pci 0000:00:01.0: reg 0x14: [mem 0x00000000-0x0000ffff]
[    1.761515] pci 0000:00:01.0: supports D1
[    1.769509] pci 0000:00:01.0: PME# supported from D0 D1 D3hot
[    1.782527] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    1.798712] pci 0000:01:00.0: [14c3:7662] type 00 class 0x028000
[    1.810762] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit]
[    1.824331] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[    1.837791] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[    1.851490] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[    1.861916] pci 0000:00:00.0:   bridge window [io  0x0000-0x0fff]
[    1.874066] pci 0000:00:00.0:   bridge window [mem 0x60000000-0x600fffff]
[    1.887603] pci 0000:00:00.0:   bridge window [mem 0x60100000-0x601fffff pref]
[    1.902002] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[    1.915443] pci 0000:02:00.0: [14c3:7662] type 00 class 0x028000
[    1.927482] pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit]
[    1.941051] pci 0000:02:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[    1.954517] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
[    1.968154] pci 0000:00:01.0: PCI bridge to [bus 02-ff]
[    1.978594] pci 0000:00:01.0:   bridge window [io  0x0000-0x0fff]
[    1.990745] pci 0000:00:01.0:   bridge window [mem 0x00000000-0x000fffff]
[    2.004277] pci 0000:00:01.0:   bridge window [mem 0x00000000-0x000fffff pref]
[    2.018686] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[    2.031921] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[    2.045104] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[    2.058987] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000]
[    2.072171] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000]
[    2.086051] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[    2.099589] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x601fffff pref]
[    2.113987] pci 0000:00:01.0: BAR 8: assigned [mem 0x60200000-0x602fffff]
[    2.127533] pci 0000:00:01.0: BAR 9: assigned [mem 0x60300000-0x603fffff pref]
[    2.141929] pci 0000:00:00.0: BAR 1: assigned [mem 0x60400000-0x6040ffff]
[    2.155475] pci 0000:00:01.0: BAR 1: assigned [mem 0x60410000-0x6041ffff]
[    2.169011] pci 0000:00:00.0: BAR 7: assigned [io  0x1e160000-0x1e160fff]
[    2.182548] pci 0000:00:01.0: BAR 7: assigned [io  0x1e161000-0x1e161fff]
[    2.196089] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit]
[    2.210674] pci 0000:01:00.0: BAR 6: assigned [mem 0x60100000-0x6010ffff pref]
[    2.225068] pci 0000:00:00.0: PCI bridge to [bus 01]
[    2.234978] pci 0000:00:00.0:   bridge window [io  0x1e160000-0x1e160fff]
[    2.248510] pci 0000:00:00.0:   bridge window [mem 0x60000000-0x600fffff]
[    2.262041] pci 0000:00:00.0:   bridge window [mem 0x60100000-0x601fffff pref]
[    2.276450] pci 0000:02:00.0: BAR 0: assigned [mem 0x60200000-0x602fffff 64bit]
[    2.291035] pci 0000:02:00.0: BAR 6: assigned [mem 0x60300000-0x6030ffff pref]
[    2.305428] pci 0000:00:01.0: PCI bridge to [bus 02]
[    2.315329] pci 0000:00:01.0:   bridge window [io  0x1e161000-0x1e161fff]
[    2.328861] pci 0000:00:01.0:   bridge window [mem 0x60200000-0x602fffff]
[    2.342403] pci 0000:00:01.0:   bridge window [mem 0x60300000-0x603fffff pref]
[    2.357587] hctosys: unable to open rtc device (rtc0)
[    2.368408] mt7530 mdio-bus:1f: Link is Up - 1Gbps/Full - flow control off
[    2.389716] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[    2.408453] Freeing unused kernel memory: 1244K
[    2.417505] This architecture does not have kernel memory protection.
[    2.430358] Run /sbin/init as init process
[    3.340665] init: Console is alive
[    3.347707] init: - watchdog -
[    4.311733] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    4.470827] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    4.498742] init: - preinit -
[    5.521079] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
[    5.537231] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[    5.554214] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[    5.729015] random: jshn: uninitialized urandom read (4 bytes read)
[    5.800392] random: jshn: uninitialized urandom read (4 bytes read)
[    5.835486] random: jshn: uninitialized urandom read (4 bytes read)
[    6.041164] mt7530 mdio-bus:1f lan: configuring for phy/gmii link mode
[    6.054643] 8021q: adding VLAN 0 to HW filter on device lan
[   10.163009] mt7530 mdio-bus:1f lan: Link is Up - 1Gbps/Full - flow control rx/tx
[   10.177989] IPv6: ADDRCONF(NETDEV_CHANGE): lan: link becomes ready
[   10.320465] jffs2_scan_eraseblock(): End of filesystem marker found at 0x10000
[   10.334891] jffs2_build_filesystem(): unlocking the mtd device... 
[   10.334896] done.
[   10.351024] jffs2_build_filesystem(): erasing all blocks after the end marker... 
[   10.519856] random: crng init done
[   10.541505] random: 7 urandom warning(s) missed due to ratelimiting
[   56.028064] done.
[   56.031946] jffs2: notice: (613) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[   56.064749] mount_root: overlay filesystem has not been fully initialized yet
[   56.080250] mount_root: switching to jffs2 overlay
[   56.093598] overlayfs: upper fs does not support tmpfile.
[   56.657239] urandom-seed: Seed file not found (/etc/urandom.seed)
[   56.778658] mt7530 mdio-bus:1f lan: Link is Down
[   56.798161] procd: - early -
[   56.804039] procd: - watchdog -
[   57.438480] procd: - watchdog -
[   57.445204] procd: - ubus -
[   57.606095] procd: - init -
[   58.347938] kmodloader: loading kernel modules from /etc/modules.d/*
[   58.408350] Loading modules backported from Linux version v5.10.16-0-gde53befa79cf
[   58.423503] Backport generated by backports.git v5.10.16-1-0-g21d2a1d2
[   58.477448] urngd: v1.0.2 started.
[   58.489927] xt_time: kernel timezone is -0000
[   58.564229] mt7621-pci 1e140000.pcie: bus=1 slot=0 irq=19
[   58.575105] pci 0000:00:00.0: enabling device (0006 -> 0007)
[   58.586403] mt76x2e 0000:01:00.0: enabling device (0000 -> 0002)
[   58.598664] mt76x2e 0000:01:00.0: ASIC revision: 76120044
[   59.007017] mt76x2e 0000:01:00.0: ROM patch build: 20141115060606a
[   59.023076] mt76x2e 0000:01:00.0: Firmware Version: 0.0.00
[   59.034027] mt76x2e 0000:01:00.0: Build: 1
[   59.042183] mt76x2e 0000:01:00.0: Build Time: 201507311614____
[   59.070372] mt76x2e 0000:01:00.0: Firmware running!
[   59.082297] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   59.088071] mt7621-pci 1e140000.pcie: bus=2 slot=1 irq=20
[   59.098949] pci 0000:00:01.0: enabling device (0004 -> 0007)
[   59.110254] mt76x2e 0000:02:00.0: enabling device (0000 -> 0002)
[   59.122613] mt76x2e 0000:02:00.0: ASIC revision: 76020044
[   59.530412] mt76x2e 0000:02:00.0: ROM patch already applied
[   59.542648] mt76x2e 0000:02:00.0: Firmware Version: 0.0.00
[   59.553649] mt76x2e 0000:02:00.0: Build: 1
[   59.561953] mt76x2e 0000:02:00.0: Build Time: 201507311614____
[   59.590476] mt76x2e 0000:02:00.0: Firmware running!
[   59.603369] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[   59.640617] PPP generic driver version 2.4.2
[   59.651562] NET: Registered protocol family 24
[   59.698088] kmodloader: done loading kernel modules from /etc/modules.d/*
[   68.983459] mtk_soc_eth 1e100000.ethernet eth0: Link is Down
[   69.006269] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
[   69.022530] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[   69.039631] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   69.056950] mt7530 mdio-bus:1f lan: configuring for phy/gmii link mode
[   69.071020] 8021q: adding VLAN 0 to HW filter on device lan
[   69.090774] br-lan: port 1(lan) entered blocking state
[   69.101381] br-lan: port 1(lan) entered disabled state
[   69.120507] device lan entered promiscuous mode
[   69.129640] device eth0 entered promiscuous mode
[   71.259336] br-lan: port 2(wlan1) entered blocking state
[   71.270014] br-lan: port 2(wlan1) entered disabled state
[   71.281187] device wlan1 entered promiscuous mode
[   71.753868] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[   71.767084] br-lan: port 2(wlan1) entered blocking state
[   71.777809] br-lan: port 2(wlan1) entered forwarding state
[   71.791423] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   72.324606] br-lan: port 3(wlan0) entered blocking state
[   72.335234] br-lan: port 3(wlan0) entered disabled state
[   72.346523] device wlan0 entered promiscuous mode
[   72.356242] br-lan: port 3(wlan0) entered blocking state
[   72.366908] br-lan: port 3(wlan0) entered forwarding state
[   72.378811] br-lan: port 3(wlan0) entered disabled state
[   73.170883] mt7530 mdio-bus:1f lan: Link is Up - 1Gbps/Full - flow control rx/tx
[   73.185718] br-lan: port 1(lan) entered blocking state
[   73.196021] br-lan: port 1(lan) entered forwarding state
[  153.472300] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[  153.485354] br-lan: port 3(wlan0) entered blocking state
[  153.496035] br-lan: port 3(wlan0) entered forwarding state

Loading...

Available keyboard shortcuts

Tasklist

Task Details

Task Editing