Skip to content
New issue

Have a question about this project? Sign up for a free GitHub account to open an issue and contact its maintainers and the community.

By clicking “Sign up for GitHub”, you agree to our terms of service and privacy statement. We’ll occasionally send you account related emails.

Already on GitHub? Sign in to your account

FS#3456 - tl-wdr3600 2,4ghz wireless not work 40Mhz channel and multiple disconnection in client mode #8326

Open
openwrt-bot opened this issue Nov 16, 2020 · 1 comment
Labels

Comments

@openwrt-bot
Copy link

re-bob:

Supply the following if possible:

  • Device problem occurs on
    TL WDR3600 v1
  • Software versions of OpenWrt/LEDE release, packages, etc.
    OpenWrt 19.07.4 r11208-ce6496d796 / LuCI openwrt-19.07 branch git-20.313.59566-7460e9d
    kmod-cfg80211 - 4.14.195+4.19.137-1-2
    kmod-mac80211 - 4.14.195+4.19.137-1-2
    Generic 802.11bgn

root@OpenWrt:~# iw phy phy0 info
Wiphy phy0
max # scan SSIDs: 4
max scan IEs length: 2257 bytes
max # sched scan SSIDs: 0
max # match sets: 0
max # scan plans: 1
max scan plan interval: -1
max scan plan iterations: 0
Retry short limit: 7
Retry long limit: 4
Coverage class: 0 (up to 0m)
Device supports AP-side u-APSD.
Device supports T-DLS.
Available Antennas: TX 0x3 RX 0x3
Configured Antennas: TX 0x3 RX 0x3
Supported interface modes:
* IBSS
* managed
* AP
* AP/VLAN
* monitor
* mesh point
* P2P-client
* P2P-GO
* outside context of a BSS
Band 1:
Capabilities: 0x11ef
RX LDPC
HT20/HT40
SM Power Save disabled
RX HT20 SGI
RX HT40 SGI
TX STBC
RX STBC 1-stream
Max AMSDU length: 3839 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 8 usec (0x06)
HT TX/RX MCS rate indexes supported: 0-15
Frequencies:
* 2412 MHz [1] (20.0 dBm)
* 2417 MHz [2] (20.0 dBm)
* 2422 MHz [3] (20.0 dBm)
* 2427 MHz [4] (20.0 dBm)
* 2432 MHz [5] (20.0 dBm)
* 2437 MHz [6] (20.0 dBm)
* 2442 MHz [7] (20.0 dBm)
* 2447 MHz [8] (20.0 dBm)
* 2452 MHz [9] (20.0 dBm)
* 2457 MHz [10] (20.0 dBm)
* 2462 MHz [11] (20.0 dBm)
* 2467 MHz [12] (20.0 dBm)
* 2472 MHz [13] (20.0 dBm)
* 2484 MHz [14] (disabled)
valid interface combinations:
* #{ managed } <= 2048, #{ AP, mesh point } <= 8, #{ P2P-client, P2P-GO } <= 1, #{ IBSS } <= 1,
total <= 2048, #channels <= 1, STA/AP BI must match, radar detect widths: { 20 MHz (no HT), 20 MHz, 40 MHz }

    HT Capability overrides:
             * MCS: ff ff ff ff ff ff ff ff ff ff
             * maximum A-MSDU length
             * supported channel width
             * short GI for 40 MHz
             * max A-MPDU length exponent
             * min MPDU start spacing
    Supported extended features:
            * [ RRM ]: RRM
            * [ CQM_RSSI_LIST ]: multiple CQM_RSSI_THOLD records
            * [ CONTROL_PORT_OVER_NL80211 ]: control port over nl80211
            * [ TXQS ]: FQ-CoDel-enabled intermediate TXQs
  • Steps to reproduce

Connect to a wifi without encryption

root@OpenWrt:~# cat /var/run/wpa_supplicant-wlan0.conf

country=IT
network={
scan_ssid=1
ssid="free-WiFi"
key_mgmt=NONE
beacon_int=100
}

multiple disconnections have occurred and the 40 Mhz channel size does not work but only 20 Mhz even though I select "40ht" in the settings, but the parameter is ignored

[ 9310.919517] wlan0: authenticate with aa:bb:cc:dd:ee:ff
[ 9310.942108] wlan0: send auth to aa:bb:cc:dd:ee:ff (try 1/3)
[ 9310.949574] wlan0: authenticated
[ 9310.958118] wlan0: associate with aa:bb:cc:dd:ee:ff (try 1/3)
[ 9310.967484] wlan0: RX AssocResp from aa:bb:cc:dd:ee:ff (capab=0x401 status=0 aid=1)
[ 9310.975528] wlan0: associated
[ 9310.980545] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[14386.169903] wlan0: authenticate with aa:bb:cc:dd:ee:ff
[14386.192135] wlan0: send auth to aa:bb:cc:dd:ee:ff (try 1/3)
[14386.221460] wlan0: authenticated
[14386.258393] wlan0: associate with aa:bb:cc:dd:ee:ff (try 1/3)
[14386.268632] wlan0: RX AssocResp from aa:bb:cc:dd:ee:ff (capab=0x401 status=0 aid=1)
[14386.276858] wlan0: associated
[150814.159420] wlan0: cannot understand ECSA IE operating class, 4, ignoring
[150814.166639] wlan0: AP aa:bb:cc:dd:ee:ff tries to chanswitch to same channel, ignore
[152268.305454] wlan0: authenticate with aa:bb:cc:dd:ee:ff
[152268.327706] wlan0: send auth to aa:bb:cc:dd:ee:ff (try 1/3)
[152268.464092] wlan0: send auth to aa:bb:cc:dd:ee:ff (try 2/3)
[152268.584729] wlan0: send auth to aa:bb:cc:dd:ee:ff (try 3/3)
[152268.724110] wlan0: authentication with aa:bb:cc:dd:ee:ff timed out
[152270.325114] wlan0: authenticate with aa:bb:cc:dd:ee:ff
[152270.347410] wlan0: send auth to aa:bb:cc:dd:ee:ff (try 1/3)
[152270.447867] wlan0: send auth to aa:bb:cc:dd:ee:ff (try 2/3)
[152270.550270] wlan0: send auth to aa:bb:cc:dd:ee:ff (try 3/3)
[152270.646190] wlan0: authentication with aa:bb:cc:dd:ee:ff timed out
[152272.215055] wlan0: authenticate with aa:bb:cc:dd:ee:ff
[152272.237313] wlan0: send auth to aa:bb:cc:dd:ee:ff (try 1/3)
[152272.244860] wlan0: authenticated
[152272.254162] wlan0: associate with aa:bb:cc:dd:ee:ff (try 1/3)
[152272.263364] wlan0: RX AssocResp from aa:bb:cc:dd:ee:ff (capab=0x401 status=0 aid=1)
[152272.271469] wlan0: associated
[155444.244711] wlan0: authenticate with aa:bb:cc:dd:ee:ff
[155444.266922] wlan0: send auth to aa:bb:cc:dd:ee:ff (try 1/3)
[155444.350695] wlan0: send auth to aa:bb:cc:dd:ee:ff (try 2/3)
[155444.415256] wlan0: send auth to aa:bb:cc:dd:ee:ff (try 3/3)
[155444.500674] wlan0: authentication with aa:bb:cc:dd:ee:ff timed out
[155448.144033] wlan0: authenticate with aa:bb:cc:dd:ee:ff
[155448.166261] wlan0: send auth to aa:bb:cc:dd:ee:ff (try 1/3)
[155448.179452] wlan0: authenticated
[155448.193209] wlan0: associate with aa:bb:cc:dd:ee:ff (try 1/3)
[155448.203713] wlan0: RX AssocResp from aa:bb:cc:dd:ee:ff (capab=0x401 status=0 aid=1)
[155448.211780] wlan0: associated
[169407.360674] wlan0: cannot understand ECSA IE operating class, 4, ignoring
[169407.367880] wlan0: AP aa:bb:cc:dd:ee:ff tries to chanswitch to same channel, ignore
[180804.557552] wlan0: cannot understand ECSA IE operating class, 4, ignoring
[181313.033648] wlan0: authenticate with aa:bb:cc:dd:ee:ff
[181313.055903] wlan0: send auth to aa:bb:cc:dd:ee:ff (try 1/3)
[181313.209864] wlan0: authenticated
[181313.222629] wlan0: associate with aa:bb:cc:dd:ee:ff (try 1/3)
[181313.256578] wlan0: RX AssocResp from aa:bb:cc:dd:ee:ff (capab=0x401 status=0 aid=1)
[181313.264725] wlan0: associated
[183301.022778] wlan0: authenticate with aa:bb:cc:dd:ee:ff
[183301.044996] wlan0: send auth to aa:bb:cc:dd:ee:ff (try 1/3)
[183301.067456] wlan0: authenticated
[183301.138782] wlan0: associate with aa:bb:cc:dd:ee:ff (try 1/3)
[183301.155290] wlan0: RX AssocResp from aa:bb:cc:dd:ee:ff (capab=0x401 status=0 aid=1)
[183301.163425] wlan0: associated
[185525.016165] wlan0: authenticate with aa:bb:cc:dd:ee:ff
[185525.038608] wlan0: send auth to aa:bb:cc:dd:ee:ff (try 1/3)
[185525.060327] wlan0: authenticated
[185525.105330] wlan0: associate with aa:bb:cc:dd:ee:ff (try 1/3)
[185525.115047] wlan0: RX AssocResp from aa:bb:cc:dd:ee:ff (capab=0x401 status=0 aid=1)
[185525.123140] wlan0: associated
[185969.001341] wlan0: authenticate with aa:bb:cc:dd:ee:ff
[185969.023612] wlan0: send auth to aa:bb:cc:dd:ee:ff (try 1/3)
[185969.149850] wlan0: send auth to aa:bb:cc:dd:ee:ff (try 2/3)
[185969.259845] wlan0: send auth to aa:bb:cc:dd:ee:ff (try 3/3)
[185969.381172] wlan0: authentication with aa:bb:cc:dd:ee:ff timed out
[185970.980914] wlan0: authenticate with aa:bb:cc:dd:ee:ff
[185971.003176] wlan0: send auth to aa:bb:cc:dd:ee:ff (try 1/3)
[185971.019374] wlan0: authenticated
[185971.049820] wlan0: associate with aa:bb:cc:dd:ee:ff (try 1/3)
[185971.060003] wlan0: RX AssocResp from aa:bb:cc:dd:ee:ff (capab=0x401 status=0 aid=1)
[185971.068073] wlan0: associated
[186860.996960] wlan0: authenticate with aa:bb:cc:dd:ee:ff
[186861.019228] wlan0: send auth to aa:bb:cc:dd:ee:ff (try 1/3)
[186861.043203] wlan0: authenticated
[186861.075375] wlan0: associate with aa:bb:cc:dd:ee:ff (try 1/3)
[186861.090284] wlan0: RX AssocResp from aa:bb:cc:dd:ee:ff (capab=0x401 status=0 aid=1)
[186861.098418] wlan0: associated
[186868.836153] wlan0: deauthenticating from aa:bb:cc:dd:ee:ff by local choice (Reason: 3=DEAUTH_LEAVING)
[186870.049178] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[186871.506366] wlan0: authenticate with aa:bb:cc:dd:ee:ff
[186871.528653] wlan0: send auth to aa:bb:cc:dd:ee:ff (try 1/3)
[186871.544687] wlan0: authenticated
[186871.594551] wlan0: associate with aa:bb:cc:dd:ee:ff (try 1/3)
[186871.613869] wlan0: RX AssocResp from aa:bb:cc:dd:ee:ff (capab=0x401 status=0 aid=1)
[186871.621999] wlan0: associated
[186871.626962] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[187310.993064] wlan0: authenticate with aa:bb:cc:dd:ee:ff
[187311.015717] wlan0: send auth to aa:bb:cc:dd:ee:ff (try 1/3)
[187311.111429] wlan0: send auth to aa:bb:cc:dd:ee:ff (try 2/3)
[187311.233939] wlan0: send auth to aa:bb:cc:dd:ee:ff (try 3/3)
[187311.353993] wlan0: authenticated
[187311.361174] wlan0: associate with aa:bb:cc:dd:ee:ff (try 1/3)
[187311.382512] wlan0: RX AssocResp from aa:bb:cc:dd:ee:ff (capab=0x401 status=0 aid=1)
[187311.390594] wlan0: associated
[187757.053230] wlan0: authenticate with aa:bb:cc:dd:ee:ff
[187757.075521] wlan0: send auth to aa:bb:cc:dd:ee:ff (try 1/3)
[187757.088849] wlan0: authenticated
[187757.139109] wlan0: associate with aa:bb:cc:dd:ee:ff (try 1/3)
[187757.149248] wlan0: RX AssocResp from aa:bb:cc:dd:ee:ff (capab=0x401 status=0 aid=1)
[187757.157302] wlan0: associated
[188670.468838] wlan0: cannot understand ECSA IE operating class, 4, ignoring
[188670.475883] wlan0: AP aa:bb:cc:dd:ee:ff tries to chanswitch to same channel, ignore
[189088.021521] wlan0: authenticate with aa:bb:cc:dd:ee:ff
[189088.043814] wlan0: send auth to aa:bb:cc:dd:ee:ff (try 1/3)
[189088.169749] wlan0: send auth to aa:bb:cc:dd:ee:ff (try 2/3)
[189088.299751] wlan0: send auth to aa:bb:cc:dd:ee:ff (try 3/3)
[189088.359034] wlan0: authentication with aa:bb:cc:dd:ee:ff timed out
[189089.971099] wlan0: authenticate with aa:bb:cc:dd:ee:ff
[189089.993326] wlan0: send auth to aa:bb:cc:dd:ee:ff (try 1/3)
[189090.009912] wlan0: authenticated
[189090.039699] wlan0: associate with aa:bb:cc:dd:ee:ff (try 1/3)
[189090.049231] wlan0: RX AssocResp from aa:bb:cc:dd:ee:ff (capab=0x401 status=0 aid=1)
[189090.057352] wlan0: associated
[189093.870846] wlan0: deauthenticating from aa:bb:cc:dd:ee:ff by local choice (Reason: 3=DEAUTH_LEAVING)
[189095.520884] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[189096.970549] wlan0: authenticate with aa:bb:cc:dd:ee:ff
[189096.992821] wlan0: send auth to aa:bb:cc:dd:ee:ff (try 1/3)
[189097.006463] wlan0: authenticated
[189097.048873] wlan0: associate with aa:bb:cc:dd:ee:ff (try 1/3)
[189097.059923] wlan0: RX AssocResp from aa:bb:cc:dd:ee:ff (capab=0x401 status=0 aid=1)
[189097.067986] wlan0: associated
[189097.073072] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[189534.976401] wlan0: authenticate with 92:36:6d:93:99:85
[189534.998671] wlan0: send auth to 92:36:6d:93:99:85 (try 1/3)
[189535.094182] wlan0: send auth to 92:36:6d:93:99:85 (try 2/3)
[189535.183706] wlan0: send auth to 92:36:6d:93:99:85 (try 3/3)
[189535.271126] wlan0: authentication with 92:36:6d:93:99:85 timed out
[189536.446534] wlan0: authenticate with aa:bb:cc:dd:ee:ff
[189536.468847] wlan0: send auth to aa:bb:cc:dd:ee:ff (try 1/3)
[189536.495448] wlan0: authenticated
[189536.535539] wlan0: associate with aa:bb:cc:dd:ee:ff (try 1/3)
[189536.554540] wlan0: RX AssocResp from aa:bb:cc:dd:ee:ff (capab=0x401 status=0 aid=1)
[189536.562656] wlan0: associated
[201274.903601] wlan0: authenticate with aa:bb:cc:dd:ee:ff
[201274.925850] wlan0: send auth to aa:bb:cc:dd:ee:ff (try 1/3)
[201275.042060] wlan0: send auth to aa:bb:cc:dd:ee:ff (try 2/3)
[201275.162035] wlan0: send auth to aa:bb:cc:dd:ee:ff (try 3/3)
[201275.292501] wlan0: authentication with aa:bb:cc:dd:ee:ff timed out
[201276.883507] wlan0: authenticate with aa:bb:cc:dd:ee:ff
[201276.905711] wlan0: send auth to aa:bb:cc:dd:ee:ff (try 1/3)
[201276.932138] wlan0: authenticated
[201276.942689] wlan0: associate with aa:bb:cc:dd:ee:ff (try 1/3)
[201276.952788] wlan0: RX AssocResp from aa:bb:cc:dd:ee:ff (capab=0x401 status=0 aid=1)
[201276.960847] wlan0: associated
[237811.689601] wlan0: authenticate with aa:bb:cc:dd:ee:ff
[237811.712053] wlan0: send auth to aa:bb:cc:dd:ee:ff (try 1/3)
[237811.738528] wlan0: authenticated
[237811.778333] wlan0: associate with aa:bb:cc:dd:ee:ff (try 1/3)
[237811.796957] wlan0: RX AssocResp from aa:bb:cc:dd:ee:ff (capab=0x401 status=0 aid=1)
[237811.805098] wlan0: associated
[237819.383155] wlan0: deauthenticating from aa:bb:cc:dd:ee:ff by local choice (Reason: 3=DEAUTH_LEAVING)
[237820.815792] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[237822.219411] wlan0: authenticate with aa:bb:cc:dd:ee:ff
[237822.241683] wlan0: send auth to aa:bb:cc:dd:ee:ff (try 1/3)
[237822.283742] wlan0: authenticated
[237822.297883] wlan0: associate with aa:bb:cc:dd:ee:ff (try 1/3)
[237822.310358] wlan0: RX AssocResp from aa:bb:cc:dd:ee:ff (capab=0x401 status=0 aid=1)
[237822.318491] wlan0: associated
[237822.325975] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready

@openwrt-bot
Copy link
Author

re-bob:

I have found other similar problems and is a kernel/driver problem, see

[[https://bugs.launchpad.net/ubuntu/+source/linux/+bug/548992|https://bugs.launchpad.net/ubuntu/+source/linux/+bug/548992]]

[[https://ubuntuforums.org/showthread.php?t=881354&s=a943200d2c6e31236f47bfebb4148917|https://ubuntuforums.org/showthread.php?t=881354&s=a943200d2c6e31236f47bfebb4148917]]

Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment
Labels
Projects
None yet
Development

No branches or pull requests

1 participant