OpenWrt/LEDE Project

  • Status Unconfirmed
  • Percent Complete
    0%
  • Task Type Bug Report
  • Category Base system
  • Assigned To No-one
  • Operating System All
  • Severity Low
  • Priority Very Low
  • Reported Version Trunk
  • Due in Version Undecided
  • Due Date Undecided
  • Private
Attached to Project: OpenWrt/LEDE Project
Opened by tiagofreire-pt - 12.11.2020

FS#3446 - No WAN on EA7500 V1 since snapshots of November 9th 2020

# logread
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.000000] Booting Linux on physical CPU 0x0
Thu Nov 12 20:20:17 2020 kern.notice kernel: [    0.000000] Linux version 5.4.75 (redalert@megadef) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r14926-41b867165d)) #0 SMP Thu Nov 12 17:21:55 2020
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5787d
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.000000] CPU: div instructions available: patching division code
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.000000] OF: fdt: Machine model: Linksys EA7500 V1 WiFi Router
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.000000] Memory policy: Data cache writealloc
Thu Nov 12 20:20:17 2020 kern.debug kernel: [    0.000000] On node 0 totalpages: 57344
Thu Nov 12 20:20:17 2020 kern.debug kernel: [    0.000000]   Normal zone: 504 pages used for memmap
Thu Nov 12 20:20:17 2020 kern.debug kernel: [    0.000000]   Normal zone: 0 pages reserved
Thu Nov 12 20:20:17 2020 kern.debug kernel: [    0.000000]   Normal zone: 57344 pages, LIFO batch:15
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.000000] percpu: Embedded 15 pages/cpu s30156 r8192 d23092 u61440
Thu Nov 12 20:20:17 2020 kern.debug kernel: [    0.000000] pcpu-alloc: s30156 r8192 d23092 u61440 alloc=15*4096
Thu Nov 12 20:20:17 2020 kern.debug kernel: [    0.000000] pcpu-alloc: [0] 0 [0] 1
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 56840
Thu Nov 12 20:20:17 2020 kern.notice kernel: [    0.000000] Kernel command line: console=ttyMSM0,115200n8 ubi.mtd=16
Thu Nov 12 20:20:17 2020 kern.notice kernel: [    0.000000] Bootloader command line (ignored): console=ttyHSL1,115200n8 init=/sbin/init rootfstype=squashfs ubi.mtd=16,2048 ubi.block=0,0 root=/dev/ubiblock0_0 rootwait ro
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.000000] Memory: 217252K/229376K available (5928K kernel code, 191K rwdata, 1508K rodata, 1024K init, 228K bss, 12124K reserved, 0K cma-reserved, 0K highmem)
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.000000] rcu: Hierarchical RCU implementation.
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
Thu Nov 12 20:20:17 2020 kern.notice kernel: [    0.000000] random: get_random_bytes called from start_kernel+0x340/0x4e8 with crng_init=0
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.000000] clocksource: dg_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 305801671480 ns
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.000007] sched_clock: 32 bits at 6MHz, resolution 160ns, wraps every 343597383600ns
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.000020] Switching to timer-based delay loop, resolution 160ns
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.000244] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.50 BogoMIPS (lpj=62500)
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.000263] pid_max: default: 32768 minimum: 301
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.000459] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.000477] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.001497] CPU: Testing write buffer coherency: ok
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.002672] Setting up static identity map for 0x42300000 - 0x42300060
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.002849] rcu: Hierarchical SRCU implementation.
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.003359] smp: Bringing up secondary CPUs ...
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.005273] smp: Brought up 1 node, 2 CPUs
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.005289] SMP: Total of 2 processors activated (25.00 BogoMIPS).
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.005299] CPU: All CPU(s) started in SVC mode.
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.015520] VFP support v0.3: implementor 51 architecture 64 part 4d variant 2 rev 0
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.015679] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.015706] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.015872] pinctrl core: initialized pinctrl subsystem
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.017039] NET: Registered protocol family 16
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.017352] DMA: preallocated 256 KiB pool for atomic coherent allocations
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.018694] cpuidle: using governor ladder
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.018761] cpuidle: using governor menu
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.050126] usbcore: registered new interface driver usbfs
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.050215] usbcore: registered new interface driver hub
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.050298] usbcore: registered new device driver usb
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.050370] pps_core: LinuxPPS API ver. 1 registered
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.050382] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.050421] PTP clock support registered
Thu Nov 12 20:20:17 2020 kern.warn kernel: [    0.051184] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.052451] clocksource: Switched to clocksource dg_timer
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.053351] thermal_sys: Registered thermal governor 'step_wise'
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.055755] NET: Registered protocol family 2
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.056325] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.056367] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear)
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.056402] TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear)
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.056435] TCP: Hash tables configured (established 2048 bind 2048)
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.056538] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.056570] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.056794] NET: Registered protocol family 1
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.056848] PCI: CLS 0 bytes, default 64
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.058196] workingset: timestamp_bits=14 max_order=16 bucket_order=2
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.065135] squashfs: version 4.0 (2009/01/31) Phillip Lougher
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.065151] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
Thu Nov 12 20:20:17 2020 kern.warn kernel: [    0.104920] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda not found, using dummy regulator
Thu Nov 12 20:20:17 2020 kern.warn kernel: [    0.105068] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda_phy not found, using dummy regulator
Thu Nov 12 20:20:17 2020 kern.warn kernel: [    0.105180] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda_refclk not found, using dummy regulator
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.105450] qcom-pcie 1b500000.pci: host bridge /soc/pci@1b500000 ranges:
Thu Nov 12 20:20:17 2020 kern.debug kernel: [    0.105477] qcom-pcie 1b500000.pci: Parsing ranges property...
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.105523] qcom-pcie 1b500000.pci:    IO 0x0fe00000..0x0fefffff -> 0x0fe00000
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.105561] qcom-pcie 1b500000.pci:   MEM 0x08000000..0x0fdfffff -> 0x08000000
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.327873] qcom-pcie 1b500000.pci: Link up
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.328043] qcom-pcie 1b500000.pci: PCI host bridge to bus 0000:00
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.328069] pci_bus 0000:00: root bus resource [bus 00-ff]
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.328090] pci_bus 0000:00: root bus resource [io  0x0000-0xfffff] (bus address [0xfe00000-0xfefffff])
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.328106] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fdfffff]
Thu Nov 12 20:20:17 2020 kern.debug kernel: [    0.328124] pci_bus 0000:00: scanning bus
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.328171] pci 0000:00:00.0: [17cb:0101] type 01 class 0xff0000
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.328337] pci 0000:00:00.0: supports D1
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.328355] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
Thu Nov 12 20:20:17 2020 kern.debug kernel: [    0.328378] pci 0000:00:00.0: PME# disabled
Thu Nov 12 20:20:17 2020 kern.debug kernel: [    0.332215] pci_bus 0000:00: fixups for bus
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.332239] PCI: bus0: Fast back to back transfers disabled
Thu Nov 12 20:20:17 2020 kern.debug kernel: [    0.332259] pci 0000:00:00.0: scanning [bus 01-ff] behind bridge, pass 0
Thu Nov 12 20:20:17 2020 kern.debug kernel: [    0.332391] pci_bus 0000:01: scanning bus
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.332581] pci 0000:01:00.0: [168c:0040] type 00 class 0x028000
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.333077] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.334319] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
Thu Nov 12 20:20:17 2020 kern.debug kernel: [    0.334367] pci 0000:01:00.0: PME# disabled
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.334629] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5 GT/s x1 link)
Thu Nov 12 20:20:17 2020 kern.debug kernel: [    0.338410] pci_bus 0000:01: fixups for bus
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.338486] PCI: bus1: Fast back to back transfers disabled
Thu Nov 12 20:20:17 2020 kern.debug kernel: [    0.338503] pci_bus 0000:01: bus scan returning with max=01
Thu Nov 12 20:20:17 2020 kern.debug kernel: [    0.338522] pci 0000:00:00.0: scanning [bus 01-ff] behind bridge, pass 1
Thu Nov 12 20:20:17 2020 kern.debug kernel: [    0.338542] pci_bus 0000:00: bus scan returning with max=ff
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.338576] pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x081fffff]
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.338602] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x081fffff 64bit]
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.338739] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.338764] pci 0000:00:00.0:   bridge window [mem 0x08000000-0x081fffff]
Thu Nov 12 20:20:17 2020 kern.debug kernel: [    0.338957] pcieport 0000:00:00.0: assign IRQ: got 35
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.339722] pcieport 0000:00:00.0: AER: enabled with IRQ 36
Thu Nov 12 20:20:17 2020 kern.warn kernel: [    0.340298] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda not found, using dummy regulator
Thu Nov 12 20:20:17 2020 kern.warn kernel: [    0.340429] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda_phy not found, using dummy regulator
Thu Nov 12 20:20:17 2020 kern.warn kernel: [    0.340549] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda_refclk not found, using dummy regulator
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.340803] qcom-pcie 1b700000.pci: host bridge /soc/pci@1b700000 ranges:
Thu Nov 12 20:20:17 2020 kern.debug kernel: [    0.340825] qcom-pcie 1b700000.pci: Parsing ranges property...
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.340869] qcom-pcie 1b700000.pci:    IO 0x31e00000..0x31efffff -> 0x31e00000
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.340904] qcom-pcie 1b700000.pci:   MEM 0x2e000000..0x31dfffff -> 0x2e000000
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.569952] qcom-pcie 1b700000.pci: Link up
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.570104] qcom-pcie 1b700000.pci: PCI host bridge to bus 0001:00
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.570123] pci_bus 0001:00: root bus resource [bus 00-ff]
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.570140] pci_bus 0001:00: root bus resource [mem 0x2e000000-0x31dfffff]
Thu Nov 12 20:20:17 2020 kern.debug kernel: [    0.570157] pci_bus 0001:00: scanning bus
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.570199] pci 0001:00:00.0: [17cb:0101] type 01 class 0xff0000
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.570344] pci 0001:00:00.0: supports D1
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.570360] pci 0001:00:00.0: PME# supported from D0 D1 D3hot
Thu Nov 12 20:20:17 2020 kern.debug kernel: [    0.570377] pci 0001:00:00.0: PME# disabled
Thu Nov 12 20:20:17 2020 kern.debug kernel: [    0.574283] pci_bus 0001:00: fixups for bus
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.574306] PCI: bus0: Fast back to back transfers disabled
Thu Nov 12 20:20:17 2020 kern.debug kernel: [    0.574324] pci 0001:00:00.0: scanning [bus 01-ff] behind bridge, pass 0
Thu Nov 12 20:20:17 2020 kern.debug kernel: [    0.574444] pci_bus 0001:01: scanning bus
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.574618] pci 0001:01:00.0: [168c:0040] type 00 class 0x028000
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.574971] pci 0001:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.576115] pci 0001:01:00.0: PME# supported from D0 D3hot D3cold
Thu Nov 12 20:20:17 2020 kern.debug kernel: [    0.576160] pci 0001:01:00.0: PME# disabled
Thu Nov 12 20:20:17 2020 kern.debug kernel: [    0.580137] pci_bus 0001:01: fixups for bus
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.580209] PCI: bus1: Fast back to back transfers disabled
Thu Nov 12 20:20:17 2020 kern.debug kernel: [    0.580224] pci_bus 0001:01: bus scan returning with max=01
Thu Nov 12 20:20:17 2020 kern.debug kernel: [    0.580242] pci 0001:00:00.0: scanning [bus 01-ff] behind bridge, pass 1
Thu Nov 12 20:20:17 2020 kern.debug kernel: [    0.580260] pci_bus 0001:00: bus scan returning with max=ff
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.580288] pci 0001:00:00.0: BAR 8: assigned [mem 0x2e000000-0x2e1fffff]
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.580312] pci 0001:01:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit]
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.580437] pci 0001:00:00.0: PCI bridge to [bus 01-ff]
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.580459] pci 0001:00:00.0:   bridge window [mem 0x2e000000-0x2e1fffff]
Thu Nov 12 20:20:17 2020 kern.debug kernel: [    0.580644] pcieport 0001:00:00.0: assign IRQ: got 37
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.581356] pcieport 0001:00:00.0: AER: enabled with IRQ 38
Thu Nov 12 20:20:17 2020 kern.warn kernel: [    0.581945] qcom-pcie 1b900000.pci: 1b900000.pci supply vdda not found, using dummy regulator
Thu Nov 12 20:20:17 2020 kern.warn kernel: [    0.582067] qcom-pcie 1b900000.pci: 1b900000.pci supply vdda_phy not found, using dummy regulator
Thu Nov 12 20:20:17 2020 kern.warn kernel: [    0.582174] qcom-pcie 1b900000.pci: 1b900000.pci supply vdda_refclk not found, using dummy regulator
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.582456] qcom-pcie 1b900000.pci: host bridge /soc/pci@1b900000 ranges:
Thu Nov 12 20:20:17 2020 kern.debug kernel: [    0.582480] qcom-pcie 1b900000.pci: Parsing ranges property...
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.582520] qcom-pcie 1b900000.pci:    IO 0x35e00000..0x35efffff -> 0x35e00000
Thu Nov 12 20:20:17 2020 kern.info kernel: [    0.582555] qcom-pcie 1b900000.pci:   MEM 0x32000000..0x35dfffff -> 0x32000000
Thu Nov 12 20:20:17 2020 kern.info kernel: [    1.733889] qcom-pcie 1b900000.pci: Phy link never came up
Thu Nov 12 20:20:17 2020 kern.err kernel: [    1.735949] qcom-pcie 1b900000.pci: cannot initialize host
Thu Nov 12 20:20:17 2020 kern.warn kernel: [    1.736350] qcom-pcie: probe of 1b900000.pci failed with error -110
Thu Nov 12 20:20:17 2020 kern.info kernel: [    1.738663] L2 @ QSB rate. Forcing new rate.
Thu Nov 12 20:20:17 2020 kern.info kernel: [    1.738884] L2 @ 384000 KHz
Thu Nov 12 20:20:17 2020 kern.info kernel: [    1.739066] CPU0 @ 800000 KHz
Thu Nov 12 20:20:17 2020 kern.info kernel: [    1.739078] CPU1 @ QSB rate. Forcing new rate.
Thu Nov 12 20:20:17 2020 kern.info kernel: [    1.739207] CPU1 @ 384000 KHz
Thu Nov 12 20:20:17 2020 kern.info kernel: [    1.742989] gsbi 16300000.gsbi: GSBI port protocol: 6 crci: 0
Thu Nov 12 20:20:17 2020 kern.info kernel: [    1.745190] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
Thu Nov 12 20:20:17 2020 kern.info kernel: [    1.745982] msm_serial 16340000.serial: msm_serial: detected port #0
Thu Nov 12 20:20:17 2020 kern.info kernel: [    1.746034] msm_serial 16340000.serial: uartclk = 7372800
Thu Nov 12 20:20:17 2020 kern.info kernel: [    1.746108] 16340000.serial: ttyMSM0 at MMIO 0x16340000 (irq = 39, base_baud = 460800) is a MSM
Thu Nov 12 20:20:17 2020 kern.info kernel: [    1.746147] msm_serial: console setup on port #0
Thu Nov 12 20:20:17 2020 kern.info kernel: [    2.598600] printk: console [ttyMSM0] enabled
Thu Nov 12 20:20:17 2020 kern.info kernel: [    2.603666] msm_serial: driver initialized
Thu Nov 12 20:20:17 2020 kern.info kernel: [    2.612949] loop: module loaded
Thu Nov 12 20:20:17 2020 kern.info kernel: [    2.614525] nand: device found, Manufacturer ID: 0x01, Chip ID: 0xa1
Thu Nov 12 20:20:17 2020 kern.info kernel: [    2.614905] nand: AMD/Spansion S34MS01G2
Thu Nov 12 20:20:17 2020 kern.info kernel: [    2.621496] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
Thu Nov 12 20:20:17 2020 kern.notice kernel: [    2.625701] 19 fixed-partitions partitions found on MTD device qcom_nand.0
Thu Nov 12 20:20:17 2020 kern.notice kernel: [    2.632885] Creating 19 MTD partitions on "qcom_nand.0":
Thu Nov 12 20:20:17 2020 kern.notice kernel: [    2.639648] 0x000000000000-0x000000040000 : "SBL1"
Thu Nov 12 20:20:17 2020 kern.notice kernel: [    2.646611] 0x000000040000-0x000000180000 : "MIBIB"
Thu Nov 12 20:20:17 2020 kern.notice kernel: [    2.652707] 0x000000180000-0x0000002c0000 : "SBL2"
Thu Nov 12 20:20:17 2020 kern.notice kernel: [    2.657466] 0x0000002c0000-0x000000540000 : "SBL3"
Thu Nov 12 20:20:17 2020 kern.notice kernel: [    2.660067] random: fast init done
Thu Nov 12 20:20:17 2020 kern.notice kernel: [    2.668425] 0x000000540000-0x000000660000 : "DDRCONFIG"
Thu Nov 12 20:20:17 2020 kern.notice kernel: [    2.671232] 0x000000660000-0x000000780000 : "SSD"
Thu Nov 12 20:20:17 2020 kern.notice kernel: [    2.675496] 0x000000780000-0x000000a00000 : "TZ"
Thu Nov 12 20:20:17 2020 kern.notice kernel: [    2.682461] 0x000000a00000-0x000000c80000 : "RPM"
Thu Nov 12 20:20:17 2020 kern.notice kernel: [    2.687549] 0x000000c80000-0x000000dc0000 : "art"
Thu Nov 12 20:20:17 2020 kern.notice kernel: [    2.690515] 0x000000dc0000-0x000000ec0000 : "APPSBL"
Thu Nov 12 20:20:17 2020 kern.notice kernel: [    2.694071] 0x000000ec0000-0x000000f00000 : "u_env"
Thu Nov 12 20:20:17 2020 kern.notice kernel: [    2.697830] 0x000000f00000-0x000000f40000 : "s_env"
Thu Nov 12 20:20:17 2020 kern.notice kernel: [    2.702437] 0x000000f40000-0x000000f80000 : "devinfo"
Thu Nov 12 20:20:17 2020 kern.notice kernel: [    2.707346] 0x000000f80000-0x000003780000 : "kernel1"
Thu Nov 12 20:20:17 2020 kern.notice kernel: [    2.778212] 0x000001280000-0x000003780000 : "rootfs1"
Thu Nov 12 20:20:17 2020 kern.notice kernel: [    2.839660] 0x000003780000-0x000005f80000 : "kernel2"
Thu Nov 12 20:20:17 2020 kern.notice kernel: [    2.905980] 0x000003a80000-0x000005f80000 : "rootfs2"
Thu Nov 12 20:20:17 2020 kern.notice kernel: [    2.967364] 0x000005f80000-0x000006080000 : "sysdiag"
Thu Nov 12 20:20:17 2020 kern.notice kernel: [    2.969950] 0x000006080000-0x000008000000 : "syscfg"
Thu Nov 12 20:20:17 2020 kern.notice kernel: [    2.995820] random: crng init done
Thu Nov 12 20:20:17 2020 kern.info kernel: [    3.025346] libphy: ipq8064_mdio_bus: probed
Thu Nov 12 20:20:17 2020 kern.info kernel: [    3.046052] switch0: Atheros AR8337 rev. 2 switch registered on 37000000.mdio-mii
Thu Nov 12 20:20:17 2020 kern.info kernel: [    3.874960] libphy: Fixed MDIO Bus: probed
Thu Nov 12 20:20:17 2020 kern.info kernel: [    3.875635] ipq806x-gmac-dwmac 37200000.ethernet: IRQ eth_wake_irq not found
Thu Nov 12 20:20:17 2020 kern.info kernel: [    3.877958] ipq806x-gmac-dwmac 37200000.ethernet: IRQ eth_lpi not found
Thu Nov 12 20:20:17 2020 kern.warn kernel: [    3.885510] ipq806x-gmac-dwmac 37200000.ethernet: PTP uses main clock
Thu Nov 12 20:20:17 2020 kern.info kernel: [    3.892332] ipq806x-gmac-dwmac 37200000.ethernet: User ID: 0x10, Synopsys ID: 0x37
Thu Nov 12 20:20:17 2020 kern.info kernel: [    3.898184] ipq806x-gmac-dwmac 37200000.ethernet: 	DWMAC1000
Thu Nov 12 20:20:17 2020 kern.info kernel: [    3.905635] ipq806x-gmac-dwmac 37200000.ethernet: DMA HW capability register supported
Thu Nov 12 20:20:17 2020 kern.info kernel: [    3.911378] ipq806x-gmac-dwmac 37200000.ethernet: RX Checksum Offload Engine supported
Thu Nov 12 20:20:17 2020 kern.info kernel: [    3.919194] ipq806x-gmac-dwmac 37200000.ethernet: COE Type 2
Thu Nov 12 20:20:17 2020 kern.info kernel: [    3.927063] ipq806x-gmac-dwmac 37200000.ethernet: TX Checksum insertion supported
Thu Nov 12 20:20:17 2020 kern.info kernel: [    3.932906] ipq806x-gmac-dwmac 37200000.ethernet: Wake-Up On Lan supported
Thu Nov 12 20:20:17 2020 kern.info kernel: [    3.940198] ipq806x-gmac-dwmac 37200000.ethernet: Enhanced/Alternate descriptors
Thu Nov 12 20:20:17 2020 kern.info kernel: [    3.947056] ipq806x-gmac-dwmac 37200000.ethernet: Enabled extended descriptors
Thu Nov 12 20:20:17 2020 kern.info kernel: [    3.954586] ipq806x-gmac-dwmac 37200000.ethernet: Ring mode enabled
Thu Nov 12 20:20:17 2020 kern.info kernel: [    3.961549] ipq806x-gmac-dwmac 37200000.ethernet: Enable RX Mitigation via HW Watchdog Timer
Thu Nov 12 20:20:17 2020 kern.info kernel: [    3.967809] ipq806x-gmac-dwmac 37200000.ethernet: device MAC address 16:6b:c5:27:96:cf
Thu Nov 12 20:20:17 2020 kern.info kernel: [    3.977394] ipq806x-gmac-dwmac 37400000.ethernet: IRQ eth_wake_irq not found
Thu Nov 12 20:20:17 2020 kern.info kernel: [    3.984217] ipq806x-gmac-dwmac 37400000.ethernet: IRQ eth_lpi not found
Thu Nov 12 20:20:17 2020 kern.warn kernel: [    3.991539] ipq806x-gmac-dwmac 37400000.ethernet: PTP uses main clock
Thu Nov 12 20:20:17 2020 kern.info kernel: [    3.998261] ipq806x-gmac-dwmac 37400000.ethernet: User ID: 0x10, Synopsys ID: 0x37
Thu Nov 12 20:20:17 2020 kern.info kernel: [    4.004362] ipq806x-gmac-dwmac 37400000.ethernet: 	DWMAC1000
Thu Nov 12 20:20:17 2020 kern.info kernel: [    4.011723] ipq806x-gmac-dwmac 37400000.ethernet: DMA HW capability register supported
Thu Nov 12 20:20:17 2020 kern.info kernel: [    4.017627] ipq806x-gmac-dwmac 37400000.ethernet: RX Checksum Offload Engine supported
Thu Nov 12 20:20:17 2020 kern.info kernel: [    4.025344] ipq806x-gmac-dwmac 37400000.ethernet: COE Type 2
Thu Nov 12 20:20:17 2020 kern.info kernel: [    4.033247] ipq806x-gmac-dwmac 37400000.ethernet: TX Checksum insertion supported
Thu Nov 12 20:20:17 2020 kern.info kernel: [    4.038979] ipq806x-gmac-dwmac 37400000.ethernet: Wake-Up On Lan supported
Thu Nov 12 20:20:17 2020 kern.info kernel: [    4.046430] ipq806x-gmac-dwmac 37400000.ethernet: Enhanced/Alternate descriptors
Thu Nov 12 20:20:17 2020 kern.info kernel: [    4.053210] ipq806x-gmac-dwmac 37400000.ethernet: Enabled extended descriptors
Thu Nov 12 20:20:17 2020 kern.info kernel: [    4.060683] ipq806x-gmac-dwmac 37400000.ethernet: Ring mode enabled
Thu Nov 12 20:20:17 2020 kern.info kernel: [    4.067800] ipq806x-gmac-dwmac 37400000.ethernet: Enable RX Mitigation via HW Watchdog Timer
Thu Nov 12 20:20:18 2020 kern.info kernel: [    4.073978] ipq806x-gmac-dwmac 37400000.ethernet: device MAC address 9e:eb:13:3b:0b:e2
Thu Nov 12 20:20:18 2020 kern.info kernel: [    4.083647] i2c /dev entries driver
Thu Nov 12 20:20:18 2020 kern.notice kernel: [    4.092666] cpuidle: enable-method property 'qcom,kpss-acc-v1' found operations
Thu Nov 12 20:20:18 2020 kern.notice kernel: [    4.093946] cpuidle: enable-method property 'qcom,kpss-acc-v1' found operations
Thu Nov 12 20:20:18 2020 kern.info kernel: [    4.101615] sdhci: Secure Digital Host Controller Interface driver
Thu Nov 12 20:20:18 2020 kern.info kernel: [    4.108348] sdhci: Copyright(c) Pierre Ossman
Thu Nov 12 20:20:18 2020 kern.info kernel: [    4.114561] sdhci-pltfm: SDHCI platform and OF driver helper
Thu Nov 12 20:20:18 2020 kern.info kernel: [    4.121247] NET: Registered protocol family 10
Thu Nov 12 20:20:18 2020 kern.info kernel: [    4.127167] Segment Routing with IPv6
Thu Nov 12 20:20:18 2020 kern.info kernel: [    4.128988] NET: Registered protocol family 17
Thu Nov 12 20:20:18 2020 kern.info kernel: [    4.133980] 8021q: 802.1Q VLAN Support v1.8
Thu Nov 12 20:20:18 2020 kern.notice kernel: [    4.137039] Registering SWP/SWPB emulation handler
Thu Nov 12 20:20:18 2020 kern.info kernel: [    4.162913] qcom_rpm 108000.rpm: RPM firmware 3.0.16777342
Thu Nov 12 20:20:18 2020 kern.info kernel: [    4.179360] s1a: Bringing 0uV into 1050000-1050000uV
Thu Nov 12 20:20:18 2020 kern.info kernel: [    4.179618] s1a: supplied by regulator-dummy
Thu Nov 12 20:20:18 2020 kern.info kernel: [    4.183623] s1b: Bringing 0uV into 1050000-1050000uV
Thu Nov 12 20:20:18 2020 kern.info kernel: [    4.187842] s1b: supplied by regulator-dummy
Thu Nov 12 20:20:18 2020 kern.info kernel: [    4.192706] s2a: Bringing 0uV into 800000-800000uV
Thu Nov 12 20:20:18 2020 kern.info kernel: [    4.197112] s2a: supplied by regulator-dummy
Thu Nov 12 20:20:18 2020 kern.info kernel: [    4.201594] s2b: Bringing 0uV into 800000-800000uV
Thu Nov 12 20:20:18 2020 kern.info kernel: [    4.206134] s2b: supplied by regulator-dummy
Thu Nov 12 20:20:18 2020 kern.notice kernel: [    4.219101] ubi0: attaching mtd16
Thu Nov 12 20:20:18 2020 kern.notice kernel: [    4.490681] ubi0: scanning is finished
Thu Nov 12 20:20:18 2020 kern.notice kernel: [    4.500858] ubi0: attached mtd16 (name "rootfs2", size 37 MiB)
Thu Nov 12 20:20:18 2020 kern.notice kernel: [    4.500879] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
Thu Nov 12 20:20:18 2020 kern.notice kernel: [    4.505655] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
Thu Nov 12 20:20:18 2020 kern.notice kernel: [    4.512431] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
Thu Nov 12 20:20:18 2020 kern.notice kernel: [    4.519365] ubi0: good PEBs: 296, bad PEBs: 0, corrupted PEBs: 0
Thu Nov 12 20:20:18 2020 kern.notice kernel: [    4.526120] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
Thu Nov 12 20:20:18 2020 kern.notice kernel: [    4.532311] ubi0: max/mean erase counter: 3/1, WL threshold: 4096, image sequence number: 1587269547
Thu Nov 12 20:20:18 2020 kern.notice kernel: [    4.539420] ubi0: available PEBs: 0, total reserved PEBs: 296, PEBs reserved for bad PEB handling: 20
Thu Nov 12 20:20:18 2020 kern.info kernel: [    4.549474] block ubiblock0_0: created from ubi0:0(rootfs)
Thu Nov 12 20:20:18 2020 kern.notice kernel: [    4.549699] ubi0: background thread "ubi_bgt0d" started, PID 68
Thu Nov 12 20:20:18 2020 kern.notice kernel: [    4.557818] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
Thu Nov 12 20:20:18 2020 kern.info kernel: [    4.557825] hctosys: unable to open rtc device (rtc0)
Thu Nov 12 20:20:18 2020 kern.info kernel: [    4.595247] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
Thu Nov 12 20:20:18 2020 kern.info kernel: [    4.598547] Freeing unused kernel memory: 1024K
Thu Nov 12 20:20:18 2020 kern.info kernel: [    4.624007] Run /sbin/init as init process
Thu Nov 12 20:20:18 2020 user.info kernel: [    5.035502] init: Console is alive
Thu Nov 12 20:20:18 2020 user.info kernel: [    5.035628] init: - watchdog -
Thu Nov 12 20:20:18 2020 user.info kernel: [    5.736018] kmodloader: loading kernel modules from /etc/modules-boot.d/*
Thu Nov 12 20:20:18 2020 kern.info kernel: [    5.781420] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Thu Nov 12 20:20:18 2020 kern.notice kernel: [    5.790883] SCSI subsystem initialized
Thu Nov 12 20:20:18 2020 kern.debug kernel: [    5.801179] libata version 3.00 loaded.
Thu Nov 12 20:20:18 2020 kern.info kernel: [    5.804896] ehci-fsl: Freescale EHCI Host controller driver
Thu Nov 12 20:20:18 2020 kern.info kernel: [    5.805433] ehci-platform: EHCI generic platform driver
Thu Nov 12 20:20:18 2020 kern.info kernel: [    5.812489] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
Thu Nov 12 20:20:18 2020 kern.info kernel: [    5.815365] ohci-platform: OHCI generic platform driver
Thu Nov 12 20:20:18 2020 kern.err kernel: [    5.822823] dwc3-qcom 110f8800.usb3: IRQ hs_phy_irq not found
Thu Nov 12 20:20:18 2020 kern.err kernel: [    5.825847] dwc3-qcom 110f8800.usb3: IRQ dp_hs_phy_irq not found
Thu Nov 12 20:20:18 2020 kern.err kernel: [    5.831752] dwc3-qcom 110f8800.usb3: IRQ dm_hs_phy_irq not found
Thu Nov 12 20:20:18 2020 kern.err kernel: [    5.837897] dwc3-qcom 110f8800.usb3: IRQ ss_phy_irq not found
Thu Nov 12 20:20:18 2020 kern.err kernel: [    5.848168] dwc3-qcom 100f8800.usb3: IRQ hs_phy_irq not found
Thu Nov 12 20:20:18 2020 kern.err kernel: [    5.849458] dwc3-qcom 100f8800.usb3: IRQ dp_hs_phy_irq not found
Thu Nov 12 20:20:18 2020 kern.err kernel: [    5.855256] dwc3-qcom 100f8800.usb3: IRQ dm_hs_phy_irq not found
Thu Nov 12 20:20:18 2020 kern.err kernel: [    5.861265] dwc3-qcom 100f8800.usb3: IRQ ss_phy_irq not found
Thu Nov 12 20:20:18 2020 kern.err kernel: [    5.868640] dwc3 11000000.dwc3: Failed to get clk 'ref': -2
Thu Nov 12 20:20:18 2020 kern.err kernel: [    5.966345] dwc3 10000000.dwc3: Failed to get clk 'ref': -2
Thu Nov 12 20:20:18 2020 kern.info kernel: [    6.065308] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
Thu Nov 12 20:20:18 2020 kern.info kernel: [    6.065371] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
Thu Nov 12 20:20:18 2020 kern.info kernel: [    6.069909] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000000002010010
Thu Nov 12 20:20:18 2020 kern.info kernel: [    6.077404] xhci-hcd xhci-hcd.0.auto: irq 42, io mem 0x11000000
Thu Nov 12 20:20:18 2020 kern.info kernel: [    6.087837] hub 1-0:1.0: USB hub found
Thu Nov 12 20:20:18 2020 kern.info kernel: [    6.092573] hub 1-0:1.0: 1 port detected
Thu Nov 12 20:20:18 2020 kern.info kernel: [    6.096629] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
Thu Nov 12 20:20:18 2020 kern.info kernel: [    6.100429] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
Thu Nov 12 20:20:18 2020 kern.info kernel: [    6.105784] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
Thu Nov 12 20:20:18 2020 kern.info kernel: [    6.113833] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
Thu Nov 12 20:20:18 2020 kern.info kernel: [    6.120284] hub 2-0:1.0: USB hub found
Thu Nov 12 20:20:18 2020 kern.info kernel: [    6.128199] hub 2-0:1.0: 1 port detected
Thu Nov 12 20:20:18 2020 kern.info kernel: [    6.131944] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
Thu Nov 12 20:20:18 2020 kern.info kernel: [    6.135835] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
Thu Nov 12 20:20:18 2020 kern.info kernel: [    6.141174] xhci-hcd xhci-hcd.1.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000000002010010
Thu Nov 12 20:20:18 2020 kern.info kernel: [    6.148691] xhci-hcd xhci-hcd.1.auto: irq 43, io mem 0x10000000
Thu Nov 12 20:20:18 2020 kern.info kernel: [    6.158581] hub 3-0:1.0: USB hub found
Thu Nov 12 20:20:18 2020 kern.info kernel: [    6.163965] hub 3-0:1.0: 1 port detected
Thu Nov 12 20:20:18 2020 kern.info kernel: [    6.167892] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
Thu Nov 12 20:20:18 2020 kern.info kernel: [    6.171773] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
Thu Nov 12 20:20:18 2020 kern.info kernel: [    6.177133] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
Thu Nov 12 20:20:18 2020 kern.info kernel: [    6.185338] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
Thu Nov 12 20:20:18 2020 kern.info kernel: [    6.191568] hub 4-0:1.0: USB hub found
Thu Nov 12 20:20:18 2020 kern.info kernel: [    6.199559] hub 4-0:1.0: 1 port detected
Thu Nov 12 20:20:18 2020 user.info kernel: [    6.204241] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
Thu Nov 12 20:20:18 2020 user.info kernel: [    6.213441] init: - preinit -
Thu Nov 12 20:20:18 2020 kern.info kernel: [    8.398449] dwmac1000: Master AXI performs any burst length
Thu Nov 12 20:20:18 2020 kern.info kernel: [    8.398497] ipq806x-gmac-dwmac 37400000.ethernet eth1: No Safety Features support found
Thu Nov 12 20:20:18 2020 kern.info kernel: [    8.402930] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
Thu Nov 12 20:20:18 2020 kern.info kernel: [    8.411005] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
Thu Nov 12 20:20:18 2020 kern.info kernel: [    8.419977] ipq806x-gmac-dwmac 37400000.ethernet eth1: configuring for fixed/sgmii link mode
Thu Nov 12 20:20:18 2020 kern.info kernel: [    8.427983] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
Thu Nov 12 20:20:18 2020 kern.info kernel: [    8.435504] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
Thu Nov 12 20:20:18 2020 kern.notice kernel: [   12.626695] UBIFS (ubi0:1): Mounting in unauthenticated mode
Thu Nov 12 20:20:18 2020 kern.notice kernel: [   12.627905] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 164
Thu Nov 12 20:20:18 2020 kern.notice kernel: [   12.936033] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
Thu Nov 12 20:20:18 2020 kern.notice kernel: [   12.936082] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
Thu Nov 12 20:20:18 2020 kern.notice kernel: [   12.942981] UBIFS (ubi0:1): FS size: 29966336 bytes (28 MiB, 236 LEBs), journal size 1523712 bytes (1 MiB, 12 LEBs)
Thu Nov 12 20:20:18 2020 kern.notice kernel: [   12.952754] UBIFS (ubi0:1): reserved for root: 1415383 bytes (1382 KiB)
Thu Nov 12 20:20:18 2020 kern.notice kernel: [   12.963088] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID 8931B579-257A-4616-9377-4EBA30E90C6A, small LPT model
Thu Nov 12 20:20:18 2020 user.info kernel: [   12.983506] mount_root: overlay filesystem has not been fully initialized yet
Thu Nov 12 20:20:18 2020 user.info kernel: [   12.983846] mount_root: switching to ubifs overlay
Thu Nov 12 20:20:18 2020 user.warn kernel: [   13.327651] urandom-seed: Seed file not found (/etc/urandom.seed)
Thu Nov 12 20:20:18 2020 kern.info kernel: [   13.385488] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Down
Thu Nov 12 20:20:18 2020 user.info kernel: [   13.446916] procd: - early -
Thu Nov 12 20:20:18 2020 user.info kernel: [   13.447111] procd: - watchdog -
Thu Nov 12 20:20:18 2020 user.info kernel: [   14.025072] procd: - watchdog -
Thu Nov 12 20:20:18 2020 user.info kernel: [   14.025689] procd: - ubus -
Thu Nov 12 20:20:18 2020 user.info kernel: [   14.185163] procd: - init -
Thu Nov 12 20:20:18 2020 user.info kernel: [   14.698780] urngd: v1.0.2 started.
Thu Nov 12 20:20:18 2020 user.info kernel: [   14.731909] kmodloader: loading kernel modules from /etc/modules.d/*
Thu Nov 12 20:20:18 2020 kern.info kernel: [   14.739808] Loading modules backported from Linux version v5.8-0-gbcf876870b95
Thu Nov 12 20:20:18 2020 kern.info kernel: [   14.739832] Backport generated by backports.git v5.8-1-0-g79400d9e
Thu Nov 12 20:20:18 2020 kern.info kernel: [   14.754926] xt_time: kernel timezone is -0000
Thu Nov 12 20:20:18 2020 kern.info kernel: [   14.785169] PPP generic driver version 2.4.2
Thu Nov 12 20:20:18 2020 kern.info kernel: [   14.786097] NET: Registered protocol family 24
Thu Nov 12 20:20:18 2020 kern.debug kernel: [   14.804480] ath10k_pci 0000:01:00.0: assign IRQ: got 35
Thu Nov 12 20:20:18 2020 kern.info kernel: [   14.804503] ath10k 5.4 driver, optimized for CT firmware, probing pci device: 0x40.
Thu Nov 12 20:20:18 2020 kern.err kernel: [   14.804569] ath10k_mac_create, priv_size: 868  hw: 0563494e  hw->priv: d6ed336d
Thu Nov 12 20:20:18 2020 kern.info kernel: [   14.812241] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142)
Thu Nov 12 20:20:18 2020 kern.debug kernel: [   14.818405] ath10k_pci 0000:01:00.0: enabling bus mastering
Thu Nov 12 20:20:18 2020 kern.info kernel: [   14.818989] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
Thu Nov 12 20:20:18 2020 kern.info kernel: [   15.944067] ath10k_pci 0000:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003b01ff sub 168c:0002
Thu Nov 12 20:20:18 2020 kern.info kernel: [   15.944106] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
Thu Nov 12 20:20:18 2020 kern.info kernel: [   15.954537] ath10k_pci 0000:01:00.0: firmware ver 10.4b-ct-9980-fW-13-10af6a005 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 4a0fa880
Thu Nov 12 20:20:18 2020 kern.info kernel: [   16.025610] ath10k_pci 0000:01:00.0: board_file api 2 bmi_id 1:2 crc32 08fa09f2
Thu Nov 12 20:20:18 2020 kern.warn kernel: [   17.214899] ath10k_pci 0000:01:00.0: unsupported HTC service id: 1536
Thu Nov 12 20:20:18 2020 kern.warn kernel: [   17.218003] ath10k_pci 0000:01:00.0: 10.4 wmi init: vdevs: 16  peers: 48  tid: 96
Thu Nov 12 20:20:18 2020 kern.warn kernel: [   17.220318] ath10k_pci 0000:01:00.0: msdu-desc: 2500  skid: 32
Thu Nov 12 20:20:18 2020 kern.info kernel: [   17.300815] ath10k_pci 0000:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186  msdu-desc: 2500  sw-crypt: 0 ct-sta: 0'
Thu Nov 12 20:20:18 2020 kern.info kernel: [   17.300854] ath10k_pci 0000:01:00.0: wmi print 'free: 31080 iram: 23092 sram: 9596'
Thu Nov 12 20:20:18 2020 kern.info kernel: [   17.598372] ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1
Thu Nov 12 20:20:18 2020 kern.debug kernel: [   17.695172] ath: EEPROM regdomain sanitized
Thu Nov 12 20:20:18 2020 kern.debug kernel: [   17.695191] ath: EEPROM regdomain: 0x64
Thu Nov 12 20:20:18 2020 kern.debug kernel: [   17.695202] ath: EEPROM indicates we should expect a direct regpair map
Thu Nov 12 20:20:18 2020 kern.debug kernel: [   17.695224] ath: Country alpha2 being used: 00
Thu Nov 12 20:20:18 2020 kern.debug kernel: [   17.695235] ath: Regpair used: 0x64
Thu Nov 12 20:20:18 2020 kern.debug kernel: [   17.700236] ath10k_pci 0001:01:00.0: assign IRQ: got 37
Thu Nov 12 20:20:18 2020 kern.info kernel: [   17.700274] ath10k 5.4 driver, optimized for CT firmware, probing pci device: 0x40.
Thu Nov 12 20:20:18 2020 kern.err kernel: [   17.700402] ath10k_mac_create, priv_size: 868  hw: c2d04b42  hw->priv: 21a5082f
Thu Nov 12 20:20:18 2020 kern.info kernel: [   17.707602] ath10k_pci 0001:01:00.0: enabling device (0140 -> 0142)
Thu Nov 12 20:20:18 2020 kern.debug kernel: [   17.714152] ath10k_pci 0001:01:00.0: enabling bus mastering
Thu Nov 12 20:20:18 2020 kern.info kernel: [   17.714675] ath10k_pci 0001:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
Thu Nov 12 20:20:18 2020 kern.info kernel: [   18.449176] ath10k_pci 0001:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003b01ff sub 168c:0002
Thu Nov 12 20:20:18 2020 kern.info kernel: [   18.449209] ath10k_pci 0001:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
Thu Nov 12 20:20:18 2020 kern.info kernel: [   18.459477] ath10k_pci 0001:01:00.0: firmware ver 10.4b-ct-9980-fW-13-10af6a005 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 4a0fa880
Thu Nov 12 20:20:18 2020 kern.info kernel: [   18.531268] ath10k_pci 0001:01:00.0: board_file api 2 bmi_id 1:1 crc32 08fa09f2
Thu Nov 12 20:20:18 2020 kern.warn kernel: [   19.721533] ath10k_pci 0001:01:00.0: unsupported HTC service id: 1536
Thu Nov 12 20:20:18 2020 kern.warn kernel: [   19.724719] ath10k_pci 0001:01:00.0: 10.4 wmi init: vdevs: 16  peers: 48  tid: 96
Thu Nov 12 20:20:18 2020 kern.warn kernel: [   19.726958] ath10k_pci 0001:01:00.0: msdu-desc: 2500  skid: 32
Thu Nov 12 20:20:18 2020 kern.info kernel: [   19.805298] ath10k_pci 0001:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186  msdu-desc: 2500  sw-crypt: 0 ct-sta: 0'
Thu Nov 12 20:20:18 2020 kern.info kernel: [   19.805359] ath10k_pci 0001:01:00.0: wmi print 'free: 31080 iram: 23092 sram: 9596'
Thu Nov 12 20:20:18 2020 kern.info kernel: [   20.079050] ath10k_pci 0001:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1
Thu Nov 12 20:20:18 2020 kern.debug kernel: [   20.174331] ath: EEPROM regdomain sanitized
Thu Nov 12 20:20:18 2020 kern.debug kernel: [   20.174350] ath: EEPROM regdomain: 0x64
Thu Nov 12 20:20:18 2020 kern.debug kernel: [   20.174361] ath: EEPROM indicates we should expect a direct regpair map
Thu Nov 12 20:20:18 2020 kern.debug kernel: [   20.174385] ath: Country alpha2 being used: 00
Thu Nov 12 20:20:18 2020 kern.debug kernel: [   20.174394] ath: Regpair used: 0x64
Thu Nov 12 20:20:18 2020 user.info kernel: [   20.188134] kmodloader: done loading kernel modules from /etc/modules.d/*
Thu Nov 12 20:20:18 2020 user.notice dnsmasq: DNS rebinding protection is active, will discard upstream RFC1918 responses!
Thu Nov 12 20:20:18 2020 user.notice dnsmasq: Allowing 127.0.0.0/8 responses
Thu Nov 12 20:20:18 2020 daemon.info dnsmasq[859]: Connected to system UBus
Thu Nov 12 20:20:18 2020 daemon.info dnsmasq[859]: started, version 2.82 cachesize 150
Thu Nov 12 20:20:18 2020 daemon.info dnsmasq[859]: DNS service limited to local subnets
Thu Nov 12 20:20:18 2020 daemon.info dnsmasq[859]: compile time options: IPv6 GNU-getopt no-DBus UBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth no-DNSSEC no-ID loop-detect inotify dumpfile
Thu Nov 12 20:20:18 2020 daemon.info dnsmasq[859]: UBus support enabled: connected to system bus
Thu Nov 12 20:20:18 2020 daemon.info dnsmasq[859]: using only locally-known addresses for domain test
Thu Nov 12 20:20:18 2020 daemon.info dnsmasq[859]: using only locally-known addresses for domain onion
Thu Nov 12 20:20:18 2020 daemon.info dnsmasq[859]: using only locally-known addresses for domain localhost
Thu Nov 12 20:20:18 2020 daemon.info dnsmasq[859]: using only locally-known addresses for domain local
Thu Nov 12 20:20:18 2020 daemon.info dnsmasq[859]: using only locally-known addresses for domain invalid
Thu Nov 12 20:20:18 2020 daemon.info dnsmasq[859]: using only locally-known addresses for domain bind
Thu Nov 12 20:20:18 2020 daemon.info dnsmasq[859]: using only locally-known addresses for domain lan
Thu Nov 12 20:20:18 2020 daemon.warn dnsmasq[859]: no servers found in /tmp/resolv.conf.d/resolv.conf.auto, will retry
Thu Nov 12 20:20:18 2020 daemon.info dnsmasq[859]: read /etc/hosts - 4 addresses
Thu Nov 12 20:20:18 2020 daemon.info dnsmasq[859]: read /tmp/hosts/dhcp.cfg01411c - 0 addresses
Thu Nov 12 20:20:18 2020 authpriv.info dropbear[921]: Not backgrounding
Thu Nov 12 20:20:19 2020 daemon.notice wpa_supplicant[1030]: Successfully initialized wpa_supplicant
Thu Nov 12 20:20:20 2020 user.notice : Added device handler type: 8021ad
Thu Nov 12 20:20:20 2020 user.notice : Added device handler type: 8021q
Thu Nov 12 20:20:20 2020 user.notice : Added device handler type: macvlan
Thu Nov 12 20:20:20 2020 user.notice : Added device handler type: veth
Thu Nov 12 20:20:20 2020 user.notice : Added device handler type: bridge
Thu Nov 12 20:20:20 2020 user.notice : Added device handler type: Network device
Thu Nov 12 20:20:20 2020 user.notice : Added device handler type: tunnel
Thu Nov 12 20:20:21 2020 kern.info kernel: [   25.425459] dwmac1000: Master AXI performs any burst length
Thu Nov 12 20:20:21 2020 kern.info kernel: [   25.425509] ipq806x-gmac-dwmac 37400000.ethernet eth1: No Safety Features support found
Thu Nov 12 20:20:21 2020 kern.info kernel: [   25.429857] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
Thu Nov 12 20:20:21 2020 kern.info kernel: [   25.438023] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
Thu Nov 12 20:20:21 2020 kern.info kernel: [   25.446946] ipq806x-gmac-dwmac 37400000.ethernet eth1: configuring for fixed/sgmii link mode
Thu Nov 12 20:20:21 2020 kern.info kernel: [   25.454066] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
Thu Nov 12 20:20:21 2020 kern.info kernel: [   25.457497] br-lan: port 1(eth1.1) entered blocking state
Thu Nov 12 20:20:21 2020 kern.info kernel: [   25.471284] br-lan: port 1(eth1.1) entered disabled state
Thu Nov 12 20:20:21 2020 kern.info kernel: [   25.476838] device eth1.1 entered promiscuous mode
Thu Nov 12 20:20:21 2020 kern.info kernel: [   25.481921] device eth1 entered promiscuous mode
Thu Nov 12 20:20:21 2020 kern.info kernel: [   25.488315] br-lan: port 1(eth1.1) entered blocking state
Thu Nov 12 20:20:21 2020 kern.info kernel: [   25.491389] br-lan: port 1(eth1.1) entered forwarding state
Thu Nov 12 20:20:21 2020 daemon.notice netifd: Interface 'lan' is enabled
Thu Nov 12 20:20:21 2020 daemon.notice netifd: Interface 'lan' is setting up now
Thu Nov 12 20:20:21 2020 daemon.debug dnsmasq[859]: listening on br-lan(#7): 192.168.50.1 port 53
Thu Nov 12 20:20:21 2020 daemon.notice netifd: Interface 'lan' is now up
Thu Nov 12 20:20:21 2020 daemon.notice netifd: bridge 'br-lan' link is up
Thu Nov 12 20:20:21 2020 daemon.notice netifd: Interface 'lan' has link connectivity
Thu Nov 12 20:20:21 2020 daemon.notice netifd: VLAN 'eth1.1' link is up
Thu Nov 12 20:20:21 2020 daemon.debug dnsmasq[859]: listening on lo(#1): 127.0.0.1 port 53
Thu Nov 12 20:20:21 2020 daemon.debug dnsmasq[859]: listening on lo(#1): ::1 port 53
Thu Nov 12 20:20:21 2020 daemon.notice netifd: Interface 'loopback' is enabled
Thu Nov 12 20:20:21 2020 daemon.notice netifd: Interface 'loopback' is setting up now
Thu Nov 12 20:20:21 2020 daemon.notice netifd: Interface 'loopback' is now up
Thu Nov 12 20:20:21 2020 daemon.notice netifd: Network device 'eth1' link is up
Thu Nov 12 20:20:21 2020 daemon.notice netifd: Network device 'lo' link is up
Thu Nov 12 20:20:21 2020 daemon.notice netifd: Interface 'loopback' has link connectivity
Thu Nov 12 20:20:22 2020 user.notice firewall: Reloading firewall due to ifup of lan (br-lan)
Thu Nov 12 20:20:22 2020 daemon.notice procd: /etc/rc.d/S99bootcount: Boot count sucessfully reset to zero.
Thu Nov 12 20:20:22 2020 daemon.info procd: - init complete -
Thu Nov 12 20:20:22 2020 daemon.info urandom_seed[1487]: Seed saved (/etc/urandom.seed)
Thu Nov 12 20:20:22 2020 kern.info kernel: [   26.474577] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
Thu Nov 12 20:20:22 2020 kern.info kernel: [   26.475583] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
Thu Nov 12 20:20:22 2020 daemon.err odhcpd[1138]: Failed to send to ff02::1%lan@br-lan (Address not available)
Thu Nov 12 20:20:24 2020 daemon.debug dnsmasq[859]: listening on br-lan(#7): fd5c:7678:93f2::1 port 53
Thu Nov 12 20:20:24 2020 daemon.debug dnsmasq[859]: listening on eth1(#3): fe80::9ceb:13ff:fe3b:be2%eth1 port 53
Thu Nov 12 20:20:24 2020 daemon.debug dnsmasq[859]: listening on br-lan(#7): fe80::1691:82ff:fe83:c98%br-lan port 53
Thu Nov 12 20:20:25 2020 authpriv.info dropbear[1589]: Child connection from 192.168.50.218:55112
Thu Nov 12 20:20:25 2020 authpriv.notice dropbear[1589]: Auth succeeded with blank password for 'root' from 192.168.50.218:55112
Thu Nov 12 20:20:27 2020 daemon.info dnsmasq[859]: exiting on receipt of SIGTERM
Thu Nov 12 20:20:27 2020 daemon.info dnsmasq[1639]: Connected to system UBus
Thu Nov 12 20:20:27 2020 daemon.info dnsmasq[1639]: started, version 2.82 cachesize 150
Thu Nov 12 20:20:27 2020 daemon.info dnsmasq[1639]: DNS service limited to local subnets
Thu Nov 12 20:20:27 2020 daemon.info dnsmasq[1639]: compile time options: IPv6 GNU-getopt no-DBus UBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth no-DNSSEC no-ID loop-detect inotify dumpfile
Thu Nov 12 20:20:27 2020 daemon.info dnsmasq[1639]: UBus support enabled: connected to system bus
Thu Nov 12 20:20:27 2020 daemon.info dnsmasq-dhcp[1639]: DHCP, IP range 192.168.50.100 -- 192.168.50.249, lease time 12h
Thu Nov 12 20:20:27 2020 daemon.info dnsmasq[1639]: using only locally-known addresses for domain test
Thu Nov 12 20:20:27 2020 daemon.info dnsmasq[1639]: using only locally-known addresses for domain onion
Thu Nov 12 20:20:27 2020 daemon.info dnsmasq[1639]: using only locally-known addresses for domain localhost
Thu Nov 12 20:20:27 2020 daemon.info dnsmasq[1639]: using only locally-known addresses for domain local
Thu Nov 12 20:20:27 2020 daemon.info dnsmasq[1639]: using only locally-known addresses for domain invalid
Thu Nov 12 20:20:27 2020 daemon.info dnsmasq[1639]: using only locally-known addresses for domain bind
Thu Nov 12 20:20:27 2020 daemon.info dnsmasq[1639]: using only locally-known addresses for domain lan
Thu Nov 12 20:20:27 2020 daemon.warn dnsmasq[1639]: no servers found in /tmp/resolv.conf.d/resolv.conf.auto, will retry
Thu Nov 12 20:20:27 2020 daemon.info dnsmasq[1639]: read /etc/hosts - 4 addresses
Thu Nov 12 20:20:27 2020 daemon.info dnsmasq[1639]: read /tmp/hosts/dhcp.cfg01411c - 2 addresses
Thu Nov 12 20:20:27 2020 daemon.info dnsmasq-dhcp[1639]: read /etc/ethers - 0 addresses
Thu Nov 12 20:20:32 2020 daemon.info dnsmasq[1639]: read /etc/hosts - 4 addresses
Thu Nov 12 20:20:32 2020 daemon.info dnsmasq[1639]: read /tmp/hosts/odhcpd - 1 addresses
Thu Nov 12 20:20:32 2020 daemon.info dnsmasq[1639]: read /tmp/hosts/dhcp.cfg01411c - 2 addresses
Thu Nov 12 20:20:32 2020 daemon.info dnsmasq-dhcp[1639]: read /etc/ethers - 0 addresses
# ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
       valid_lft forever preferred_lft forever
    inet6 ::1/128 scope host 
       valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000
    link/ether 16:6b:c5:27:96:cf brd ff:ff:ff:ff:ff:ff
3: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP qlen 1000
    link/ether 9e:eb:13:3b:0b:e2 brd ff:ff:ff:ff:ff:ff
    inet6 fe80::9ceb:13ff:fe3b:be2/64 scope link 
       valid_lft forever preferred_lft forever
5: wlan0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000
    link/ether 14:91:82:83:0c:99 brd ff:ff:ff:ff:ff:ff
6: wlan1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000
    link/ether 14:91:82:83:0c:9a brd ff:ff:ff:ff:ff:ff
7: br-lan: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP qlen 1000
    link/ether 14:91:82:83:0c:98 brd ff:ff:ff:ff:ff:ff
    inet 192.168.50.1/24 brd 192.168.50.255 scope global br-lan
       valid_lft forever preferred_lft forever
    inet6 fd5c:7678:93f2::1/60 scope global 
       valid_lft forever preferred_lft forever
    inet6 fe80::1691:82ff:fe83:c98/64 scope link 
       valid_lft forever preferred_lft forever
8: eth1.1@eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue master br-lan state UP qlen 1000
    link/ether 14:91:82:83:0c:98 brd ff:ff:ff:ff:ff:ff
# cat /etc/config/network 

config interface 'loopback'
	option ifname 'lo'
	option proto 'static'
	option ipaddr '127.0.0.1'
	option netmask '255.0.0.0'

config globals 'globals'
	option ula_prefix 'fd5c:7678:93f2::/48'

config interface 'lan'
	option type 'bridge'
	option ifname 'eth1.1'
	option proto 'static'
	option ipaddr '192.168.50.1'
	option netmask '255.255.255.0'
	option ip6assign '60'

config device 'lan_eth1_1_dev'
	option name 'eth1.1'
	option macaddr 'xxxxx'

config interface 'wan'
	option ifname 'eth0.2'
	option proto 'dhcp'

config device 'wan_eth0_2_dev'
	option name 'eth0.2'
	option macaddr 'xxxxx'

config interface 'wan6'
	option ifname 'eth0.2'
	option proto 'dhcpv6'

config switch
	option name 'switch0'
	option reset '1'
	option enable_vlan '1'

config switch_vlan
	option device 'switch0'
	option vlan '1'
	option ports '2 3 4 5 6t'

config switch_vlan
	option device 'switch0'
	option vlan '2'
	option ports '1 0t'


Aleksandr Mezin commented on 13.11.2020 03:04

I have the same issue on Zyxel Armor Z2 (nbg6817)

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 5.4.75 (amezin@trx40) (gcc version 10.2.0 (OpenWrt GCC 10.2.0 r14740+187-0b31713c85)) #0 SMP Fri Nov 13 00:59:16 2020
[    0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5787d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[    0.000000] OF: fdt: Machine model: ZyXEL NBG6817
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] On node 0 totalpages: 122880
[    0.000000]   Normal zone: 960 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 122880 pages, LIFO batch:31
[    0.000000] percpu: Embedded 15 pages/cpu s29900 r8192 d23348 u61440
[    0.000000] pcpu-alloc: s29900 r8192 d23348 u61440 alloc=15*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 121920
[    0.000000] Kernel command line: rootfstype=squashfs,ext4 rootwait noinitrd root=/dev/mmcblk0p8
[    0.000000] Bootloader command line (ignored): board=NBG6817 root=/dev/mmcblk0p8 rootwait zld_ver=2.07 console=ttyHSL1,115200n8 mtdparts=m25p80:0xC0000(SBL)ro,0x40000(TZ)ro,0x40000(RPM)ro,0x80000(u-boot)ro,0x10000(env)ro,0x10000(ART)ro,0x10000(dualflag),0x210000(reserved)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 477404K/491520K available (5894K kernel code, 167K rwdata, 1476K rodata, 1024K init, 228K bss, 14116K reserved, 0K cma-reserved, 0K highmem)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] random: get_random_bytes called from start_kernel+0x334/0x4b8 with crng_init=0
[    0.000000] clocksource: dg_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 305801671480 ns
[    0.000007] sched_clock: 32 bits at 6MHz, resolution 160ns, wraps every 343597383600ns
[    0.000018] Switching to timer-based delay loop, resolution 160ns
[    0.000212] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.50 BogoMIPS (lpj=62500)
[    0.000230] pid_max: default: 32768 minimum: 301
[    0.000369] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.000385] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.000985] CPU: Testing write buffer coherency: ok
[    0.001892] Setting up static identity map for 0x42300000 - 0x42300060
[    0.002034] rcu: Hierarchical SRCU implementation.
[    0.002425] smp: Bringing up secondary CPUs ...
[    0.004134] smp: Brought up 1 node, 2 CPUs
[    0.004147] SMP: Total of 2 processors activated (25.00 BogoMIPS).
[    0.004156] CPU: All CPU(s) started in SVC mode.
[    0.013096] VFP support v0.3: implementor 51 architecture 64 part 4d variant 2 rev 0
[    0.013223] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.013249] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[    0.013346] pinctrl core: initialized pinctrl subsystem
[    0.014298] NET: Registered protocol family 16
[    0.014595] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.015818] cpuidle: using governor ladder
[    0.015873] cpuidle: using governor menu
[    0.044213] usbcore: registered new interface driver usbfs
[    0.044286] usbcore: registered new interface driver hub
[    0.044368] usbcore: registered new device driver usb
[    0.044419] pps_core: LinuxPPS API ver. 1 registered
[    0.044431] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.044460] PTP clock support registered
[    0.045152] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512
[    0.046204] clocksource: Switched to clocksource dg_timer
[    0.046897] thermal_sys: Registered thermal governor 'step_wise'
[    0.049049] NET: Registered protocol family 2
[    0.049677] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[    0.049705] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear)
[    0.049742] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear)
[    0.049794] TCP: Hash tables configured (established 4096 bind 4096)
[    0.049881] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.049908] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.050096] NET: Registered protocol family 1
[    0.050139] PCI: CLS 0 bytes, default 64
[    0.051205] workingset: timestamp_bits=30 max_order=17 bucket_order=0
[    0.056481] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.056494] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.096608] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda not found, using dummy regulator
[    0.096733] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda_phy not found, using dummy regulator
[    0.096826] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda_refclk not found, using dummy regulator
[    0.097061] qcom-pcie 1b500000.pci: host bridge /soc/pci@1b500000 ranges:
[    0.097081] qcom-pcie 1b500000.pci: Parsing ranges property...
[    0.097123] qcom-pcie 1b500000.pci:    IO 0x0fe00000..0x0fefffff -> 0x0fe00000
[    0.097165] qcom-pcie 1b500000.pci:   MEM 0x08000000..0x0fdfffff -> 0x08000000
[    0.322129] qcom-pcie 1b500000.pci: Link up
[    0.322267] qcom-pcie 1b500000.pci: PCI host bridge to bus 0000:00
[    0.322288] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.322305] pci_bus 0000:00: root bus resource [io  0x0000-0xfffff] (bus address [0xfe00000-0xfefffff])
[    0.322319] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fdfffff]
[    0.322333] pci_bus 0000:00: scanning bus
[    0.322373] pci 0000:00:00.0: [17cb:0101] type 01 class 0xff0000
[    0.322524] pci 0000:00:00.0: supports D1
[    0.322537] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[    0.322553] pci 0000:00:00.0: PME# disabled
[    0.326194] pci_bus 0000:00: fixups for bus
[    0.326213] PCI: bus0: Fast back to back transfers disabled
[    0.326230] pci 0000:00:00.0: scanning [bus 01-ff] behind bridge, pass 0
[    0.326340] pci_bus 0000:01: scanning bus
[    0.326596] pci 0000:01:00.0: [168c:0046] type 00 class 0x028000
[    0.326949] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[    0.328093] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[    0.328138] pci 0000:01:00.0: PME# disabled
[    0.331947] pci_bus 0000:01: fixups for bus
[    0.332018] PCI: bus1: Fast back to back transfers disabled
[    0.332032] pci_bus 0000:01: bus scan returning with max=01
[    0.332048] pci 0000:00:00.0: scanning [bus 01-ff] behind bridge, pass 1
[    0.332064] pci_bus 0000:00: bus scan returning with max=ff
[    0.332095] pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x081fffff]
[    0.332117] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x081fffff 64bit]
[    0.332240] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[    0.332260] pci 0000:00:00.0:   bridge window [mem 0x08000000-0x081fffff]
[    0.332430] pcieport 0000:00:00.0: assign IRQ: got 35
[    0.332871] pcieport 0000:00:00.0: AER: enabled with IRQ 36
[    0.333359] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda not found, using dummy regulator
[    0.333460] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda_phy not found, using dummy regulator
[    0.333552] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda_refclk not found, using dummy regulator
[    0.333791] qcom-pcie 1b700000.pci: host bridge /soc/pci@1b700000 ranges:
[    0.333810] qcom-pcie 1b700000.pci: Parsing ranges property...
[    0.333847] qcom-pcie 1b700000.pci:    IO 0x31e00000..0x31efffff -> 0x31e00000
[    0.333877] qcom-pcie 1b700000.pci:   MEM 0x2e000000..0x31dfffff -> 0x2e000000
[    0.563582] qcom-pcie 1b700000.pci: Link up
[    0.563713] qcom-pcie 1b700000.pci: PCI host bridge to bus 0001:00
[    0.563731] pci_bus 0001:00: root bus resource [bus 00-ff]
[    0.563745] pci_bus 0001:00: root bus resource [mem 0x2e000000-0x31dfffff]
[    0.563758] pci_bus 0001:00: scanning bus
[    0.563795] pci 0001:00:00.0: [17cb:0101] type 01 class 0xff0000
[    0.563937] pci 0001:00:00.0: supports D1
[    0.563950] pci 0001:00:00.0: PME# supported from D0 D1 D3hot
[    0.563966] pci 0001:00:00.0: PME# disabled
[    0.567656] pci_bus 0001:00: fixups for bus
[    0.567674] PCI: bus0: Fast back to back transfers disabled
[    0.567691] pci 0001:00:00.0: scanning [bus 01-ff] behind bridge, pass 0
[    0.567807] pci_bus 0001:01: scanning bus
[    0.567994] pci 0001:01:00.0: [168c:0046] type 00 class 0x028000
[    0.568370] pci 0001:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[    0.569601] pci 0001:01:00.0: PME# supported from D0 D3hot D3cold
[    0.569648] pci 0001:01:00.0: PME# disabled
[    0.569897] pci 0001:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0001:00:00.0 (capable of 4.000 Gb/s with 5 GT/s x1 link)
[    0.573520] pci_bus 0001:01: fixups for bus
[    0.573595] PCI: bus1: Fast back to back transfers disabled
[    0.573609] pci_bus 0001:01: bus scan returning with max=01
[    0.573624] pci 0001:00:00.0: scanning [bus 01-ff] behind bridge, pass 1
[    0.573641] pci_bus 0001:00: bus scan returning with max=ff
[    0.573664] pci 0001:00:00.0: BAR 8: assigned [mem 0x2e000000-0x2e1fffff]
[    0.573686] pci 0001:01:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit]
[    0.573816] pci 0001:00:00.0: PCI bridge to [bus 01-ff]
[    0.573836] pci 0001:00:00.0:   bridge window [mem 0x2e000000-0x2e1fffff]
[    0.573993] pcieport 0001:00:00.0: assign IRQ: got 37
[    0.574567] pcieport 0001:00:00.0: AER: enabled with IRQ 38
[    0.576950] L2 @ QSB rate. Forcing new rate.
[    0.577161] L2 @ 384000 KHz
[    0.577335] CPU0 @ 800000 KHz
[    0.577347] CPU1 @ QSB rate. Forcing new rate.
[    0.577475] CPU1 @ 384000 KHz
[    0.580813] gsbi 16300000.gsbi: GSBI port protocol: 6 crci: 0
[    0.582159] gsbi 1a200000.gsbi: GSBI port protocol: 3 crci: 0
[    0.583731] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    0.584443] msm_serial 16340000.serial: msm_serial: detected port #0
[    0.584487] msm_serial 16340000.serial: uartclk = 7372800
[    0.584548] 16340000.serial: ttyMSM0 at MMIO 0x16340000 (irq = 39, base_baud = 460800) is a MSM
[    0.584581] msm_serial: console setup on port #0
[    1.388051] printk: console [ttyMSM0] enabled
[    1.393013] msm_serial: driver initialized
[    1.401421] loop: module loaded
[    1.402428] spi_qup 1a280000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64
[    1.406163] spi-nor spi0.0: mx25u3235f (4096 Kbytes)
[    1.411570] 13 qcom-smem partitions found on MTD device spi0.0
[    1.416527] Creating 13 MTD partitions on "spi0.0":
[    1.422091] 0x000000000000-0x000000020000 : "0:SBL1"
[    1.427742] 0x000000020000-0x000000040000 : "0:MIBIB"
[    1.432839] 0x000000040000-0x000000060000 : "0:SBL2"
[    1.437817] 0x000000060000-0x0000000a0000 : "0:SBL3"
[    1.442784] 0x0000000a0000-0x0000000b0000 : "0:DDRCONFIG"
[    1.447845] 0x0000000b0000-0x0000000c0000 : "0:SSD"
[    1.453035] 0x0000000c0000-0x000000100000 : "0:TZ"
[    1.457779] 0x000000100000-0x000000140000 : "0:RPM"
[    1.462594] 0x000000140000-0x0000001c0000 : "0:APPSBL"
[    1.467452] 0x0000001c0000-0x0000001d0000 : "0:APPSBLENV"
[    1.472597] 0x0000001d0000-0x0000001e0000 : "0:ART"
[    1.478131] 0x0000001e0000-0x0000001f0000 : "0:DUAL_FLAG"
[    1.482745] 0x0000001f0000-0x000000400000 : "0:RESERVED"
[    1.489508] libphy: ipq8064_mdio_bus: probed
[    1.508078] switch0: Atheros AR8337 rev. 2 switch registered on 37000000.mdio-mii
[    2.352732] ar8327: qca,phy-rgmii-en is not specified
[    2.353230] libphy: Fixed MDIO Bus: probed
[    2.357490] ipq806x-gmac-dwmac 37200000.ethernet: IRQ eth_wake_irq not found
[    2.360761] ipq806x-gmac-dwmac 37200000.ethernet: IRQ eth_lpi not found
[    2.368239] ipq806x-gmac-dwmac 37200000.ethernet: PTP uses main clock
[    2.374800] ipq806x-gmac-dwmac 37200000.ethernet: User ID: 0x10, Synopsys ID: 0x37
[    2.380987] ipq806x-gmac-dwmac 37200000.ethernet: 	DWMAC1000
[    2.388439] ipq806x-gmac-dwmac 37200000.ethernet: DMA HW capability register supported
[    2.394180] ipq806x-gmac-dwmac 37200000.ethernet: RX Checksum Offload Engine supported
[    2.401963] ipq806x-gmac-dwmac 37200000.ethernet: COE Type 2
[    2.409866] ipq806x-gmac-dwmac 37200000.ethernet: TX Checksum insertion supported
[    2.415620] ipq806x-gmac-dwmac 37200000.ethernet: Wake-Up On Lan supported
[    2.423081] ipq806x-gmac-dwmac 37200000.ethernet: Enhanced/Alternate descriptors
[    2.429828] ipq806x-gmac-dwmac 37200000.ethernet: Enabled extended descriptors
[    2.437388] ipq806x-gmac-dwmac 37200000.ethernet: Ring mode enabled
[    2.444350] ipq806x-gmac-dwmac 37200000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[    2.450612] ipq806x-gmac-dwmac 37200000.ethernet: device MAC address aa:1c:6c:73:bc:63
[    2.460032] ipq806x-gmac-dwmac 37400000.ethernet: IRQ eth_wake_irq not found
[    2.467007] ipq806x-gmac-dwmac 37400000.ethernet: IRQ eth_lpi not found
[    2.474315] ipq806x-gmac-dwmac 37400000.ethernet: PTP uses main clock
[    2.480782] ipq806x-gmac-dwmac 37400000.ethernet: User ID: 0x10, Synopsys ID: 0x37
[    2.487136] ipq806x-gmac-dwmac 37400000.ethernet: 	DWMAC1000
[    2.494525] ipq806x-gmac-dwmac 37400000.ethernet: DMA HW capability register supported
[    2.500443] ipq806x-gmac-dwmac 37400000.ethernet: RX Checksum Offload Engine supported
[    2.508148] ipq806x-gmac-dwmac 37400000.ethernet: COE Type 2
[    2.515964] ipq806x-gmac-dwmac 37400000.ethernet: TX Checksum insertion supported
[    2.521861] ipq806x-gmac-dwmac 37400000.ethernet: Wake-Up On Lan supported
[    2.529234] ipq806x-gmac-dwmac 37400000.ethernet: Enhanced/Alternate descriptors
[    2.535932] ipq806x-gmac-dwmac 37400000.ethernet: Enabled extended descriptors
[    2.543573] ipq806x-gmac-dwmac 37400000.ethernet: Ring mode enabled
[    2.550571] ipq806x-gmac-dwmac 37400000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[    2.556772] ipq806x-gmac-dwmac 37400000.ethernet: device MAC address 8e:65:b0:64:8c:d0
[    2.566248] i2c /dev entries driver
[    2.575225] cpuidle: enable-method property 'qcom,kpss-acc-v1' found operations
[    2.576662] cpuidle: enable-method property 'qcom,kpss-acc-v1' found operations
[    2.584648] mmci-pl18x 12400000.sdcc: mmc0: PL180 manf 51 rev0 at 0x12400000 irq 34,0 (pio)
[    2.591255] mmci-pl18x 12400000.sdcc: DMA channels RX dma0chan1, TX dma0chan2
[    2.625560] sdhci: Secure Digital Host Controller Interface driver
[    2.625588] sdhci: Copyright(c) Pierre Ossman
[    2.630710] sdhci-pltfm: SDHCI platform and OF driver helper
[    2.637208] NET: Registered protocol family 10
[    2.641982] Segment Routing with IPv6
[    2.645122] NET: Registered protocol family 17
[    2.648906] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    2.653442] 8021q: 802.1Q VLAN Support v1.8
[    2.666398] Registering SWP/SWPB emulation handler
[    2.691536] qcom_rpm 108000.rpm: RPM firmware 3.0.16777364
[    2.704747] s1a: Bringing 0uV into 1050000-1050000uV
[    2.704984] s1a: supplied by regulator-dummy
[    2.709003] s1b: Bringing 0uV into 1050000-1050000uV
[    2.713219] s1b: supplied by regulator-dummy
[    2.718178] s2a: Bringing 0uV into 775000-775000uV
[    2.722433] s2a: supplied by regulator-dummy
[    2.727044] s2b: Bringing 0uV into 775000-775000uV
[    2.731448] s2b: supplied by regulator-dummy
[    2.744356] hctosys: unable to open rtc device (rtc0)
[    2.744798] Waiting for root device /dev/mmcblk0p8...
[    2.778020] mmc0: new high speed MMC card at address 0001
[    2.778914] mmcblk0: mmc0:0001 M62704 3.53 GiB 
[    2.782709] mmcblk0boot0: mmc0:0001 M62704 partition 1 2.00 MiB
[    2.786983] mmcblk0boot1: mmc0:0001 M62704 partition 2 2.00 MiB
[    2.792702] mmcblk0rpmb: mmc0:0001 M62704 partition 3 512 KiB, chardev (248:0)
[    2.800768]  mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10
[    2.829918] VFS: Mounted root (squashfs filesystem) readonly on device 179:8.
[    2.832072] Freeing unused kernel memory: 1024K
[    2.857101] Run /sbin/init as init process
[    2.978351] random: fast init done
[    3.039593] init: Console is alive
[    3.039706] init: - watchdog -
[    3.646305] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    3.673889] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    3.676592] SCSI subsystem initialized
[    3.682878] libata version 3.00 loaded.
[    3.685923] ehci-fsl: Freescale EHCI Host controller driver
[    3.686412] ehci-platform: EHCI generic platform driver
[    3.693389] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    3.695909] ohci-platform: OHCI generic platform driver
[    3.704379] dwc3-qcom 110f8800.usb3: IRQ hs_phy_irq not found
[    3.706955] dwc3-qcom 110f8800.usb3: IRQ dp_hs_phy_irq not found
[    3.712773] dwc3-qcom 110f8800.usb3: IRQ dm_hs_phy_irq not found
[    3.718915] dwc3-qcom 110f8800.usb3: IRQ ss_phy_irq not found
[    3.726528] dwc3-qcom 100f8800.usb3: IRQ hs_phy_irq not found
[    3.730481] dwc3-qcom 100f8800.usb3: IRQ dp_hs_phy_irq not found
[    3.736211] dwc3-qcom 100f8800.usb3: IRQ dm_hs_phy_irq not found
[    3.742356] dwc3-qcom 100f8800.usb3: IRQ ss_phy_irq not found
[    3.759084] dwc3 11000000.dwc3: Failed to get clk 'ref': -2
[    3.816850] dwc3 10000000.dwc3: Failed to get clk 'ref': -2
[    3.886118] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    3.886162] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[    3.890731] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000000002010010
[    3.898184] xhci-hcd xhci-hcd.0.auto: irq 44, io mem 0x11000000
[    3.908239] hub 1-0:1.0: USB hub found
[    3.913349] hub 1-0:1.0: 1 port detected
[    3.917383] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    3.921234] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[    3.926594] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
[    3.934143] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[    3.941735] hub 2-0:1.0: USB hub found
[    3.948989] hub 2-0:1.0: 1 port detected
[    3.952712] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[    3.956628] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
[    3.961971] xhci-hcd xhci-hcd.1.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000000002010010
[    3.969486] xhci-hcd xhci-hcd.1.auto: irq 45, io mem 0x10000000
[    3.979302] hub 3-0:1.0: USB hub found
[    3.984694] hub 3-0:1.0: 1 port detected
[    3.988702] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[    3.992577] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
[    3.997955] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
[    4.006840] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[    4.012313] hub 4-0:1.0: USB hub found
[    4.020346] hub 4-0:1.0: 1 port detected
[    4.025157] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    4.034331] init: - preinit -
[    4.311210] random: jshn: uninitialized urandom read (4 bytes read)
[    4.328981] random: jshn: uninitialized urandom read (4 bytes read)
[    4.504354] random: jshn: uninitialized urandom read (4 bytes read)
[    5.563274] dwmac1000: Master AXI performs any burst length
[    5.563318] ipq806x-gmac-dwmac 37400000.ethernet eth1: No Safety Features support found
[    5.567758] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[    5.575809] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
[    5.584763] ipq806x-gmac-dwmac 37400000.ethernet eth1: configuring for fixed/sgmii link mode
[    5.586668] urandom_read: 2 callbacks suppressed
[    5.586671] random: procd: uninitialized urandom read (4 bytes read)
[    5.592703] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[    5.611278] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[    9.845475] EXT4-fs (loop0): recovery complete
[    9.846386] EXT4-fs (loop0): mounted filesystem with ordered data mode. Opts: (null)
[    9.849155] mount_root: switching to ext4 overlay
[    9.860908] urandom-seed: Seeding with /etc/urandom.seed
[    9.904437] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Down
[    9.945774] procd: - early -
[    9.945936] procd: - watchdog -
[   10.504332] procd: - watchdog -
[   10.504877] procd: - ubus -
[   10.595507] random: ubusd: uninitialized urandom read (4 bytes read)
[   10.596872] random: ubusd: uninitialized urandom read (4 bytes read)
[   10.601346] random: ubusd: uninitialized urandom read (4 bytes read)
[   10.608276] procd: - init -
[   10.991209] urngd: v1.0.2 started.
[   10.999399] kmodloader: loading kernel modules from /etc/modules.d/*
[   11.015964] NET: Registered protocol family 38
[   11.019633] NET: Registered protocol family 15
[   11.020773] Initializing XFRM netlink socket
[   11.024734] tun: Universal TUN/TAP device driver, 1.6
[   11.025419] random: crng init done
[   11.033093] random: 1 urandom warning(s) missed due to ratelimiting
[   11.060173] gre: GRE over IPv4 demultiplexor driver
[   11.060949] ip_gre: GRE over IPv4 tunneling driver
[   11.066157] ip6_gre: GRE over IPv6 tunneling driver
[   11.120601] Mirror/redirect action on
[   11.126673] u32 classifier
[   11.126687]     input device check on
[   11.128257]     Actions configured
[   11.148738] GACT probability on
[   11.150875] Simple TC action Loaded
[   11.191168] Bridge firewalling registered
[   11.191603] Loading modules backported from Linux version v5.8-0-gbcf876870b95
[   11.194148] Backport generated by backports.git v5.8-1-0-g79400d9e
[   11.291386] nf_conntrack_rtsp v0.7 loading
[   11.310793] nf_nat_rtsp v0.7 loading
[   11.346455] wireguard: WireGuard 1.0.20201112 loaded. See www.wireguard.com for information.
[   11.346479] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
[   11.367787] IPsec XFRM device driver
[   11.399988] xt_time: kernel timezone is -0000
[   11.473038] PPP generic driver version 2.4.2
[   11.474077] PPP MPPE Compression module registered
[   11.477482] NET: Registered protocol family 24
[   11.481937] PPTP driver version 0.8.5
[   11.518339] ath10k_pci 0000:01:00.0: assign IRQ: got 35
[   11.518358] ath10k 5.4 driver, optimized for CT firmware, probing pci device: 0x46.
[   11.518416] ath10k_mac_create, priv_size: 868  hw: 9275bd48  hw->priv: 2f4fba23
[   11.532801] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142)
[   11.532883] ath10k_pci 0000:01:00.0: enabling bus mastering
[   11.533407] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[   12.370373] ath10k_pci 0000:01:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe
[   12.370402] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[   12.380883] ath10k_pci 0000:01:00.0: firmware ver 10.4b-ct-9984-fW-13-795874169 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 f3d4b769
[   14.708846] ath10k_pci 0000:01:00.0: board_file api 2 bmi_id 0:1 crc32 85498734
[   20.523226] ath10k_pci 0000:01:00.0: unsupported HTC service id: 1536
[   20.524708] ath10k_pci 0000:01:00.0: 10.4 wmi init: vdevs: 16  peers: 48  tid: 96
[   20.528726] ath10k_pci 0000:01:00.0: msdu-desc: 2500  skid: 32
[   20.610176] ath10k_pci 0000:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186  msdu-desc: 2500  sw-crypt: 0 ct-sta: 0'
[   20.611013] ath10k_pci 0000:01:00.0: wmi print 'free: 84920 iram: 13316 sram: 11224'
[   20.894482] ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1
[   20.985927] ath: EEPROM regdomain sanitized
[   20.985942] ath: EEPROM regdomain: 0x64
[   20.985952] ath: EEPROM indicates we should expect a direct regpair map
[   20.985976] ath: Country alpha2 being used: 00
[   20.985986] ath: Regpair used: 0x64
[   20.991089] ath10k_pci 0001:01:00.0: assign IRQ: got 37
[   20.991115] ath10k 5.4 driver, optimized for CT firmware, probing pci device: 0x46.
[   20.991193] ath10k_mac_create, priv_size: 868  hw: 05d4a2b1  hw->priv: 31891c8e
[   20.998219] ath10k_pci 0001:01:00.0: enabling device (0140 -> 0142)
[   21.004929] ath10k_pci 0001:01:00.0: enabling bus mastering
[   21.005496] ath10k_pci 0001:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[   21.547634] ath10k_pci 0001:01:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe
[   21.547666] ath10k_pci 0001:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[   21.558665] ath10k_pci 0001:01:00.0: firmware ver 10.4b-ct-9984-fW-13-795874169 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 f3d4b769
[   23.888521] ath10k_pci 0001:01:00.0: board_file api 2 bmi_id 0:2 crc32 85498734
[   29.727949] ath10k_pci 0001:01:00.0: unsupported HTC service id: 1536
[   29.728592] ath10k_pci 0001:01:00.0: 10.4 wmi init: vdevs: 16  peers: 48  tid: 96
[   29.733364] ath10k_pci 0001:01:00.0: msdu-desc: 2500  skid: 32
[   29.817058] ath10k_pci 0001:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186  msdu-desc: 2500  sw-crypt: 0 ct-sta: 0'
[   29.817899] ath10k_pci 0001:01:00.0: wmi print 'free: 84920 iram: 13316 sram: 11224'
[   30.260276] ath10k_pci 0001:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1
[   30.355134] ath: EEPROM regdomain sanitized
[   30.355149] ath: EEPROM regdomain: 0x64
[   30.355159] ath: EEPROM indicates we should expect a direct regpair map
[   30.355182] ath: Country alpha2 being used: 00
[   30.355192] ath: Regpair used: 0x64
[   30.365627] kmodloader: done loading kernel modules from /etc/modules.d/*
[   34.870519] dwmac1000: Master AXI performs any burst length
[   34.870547] ipq806x-gmac-dwmac 37400000.ethernet eth1: No Safety Features support found
[   34.874900] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[   34.883090] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
[   34.892002] ipq806x-gmac-dwmac 37400000.ethernet eth1: configuring for fixed/sgmii link mode
[   34.898974] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[   34.905798] br-lan: port 1(eth1.1) entered blocking state
[   34.916227] br-lan: port 1(eth1.1) entered disabled state
[   34.921939] device eth1.1 entered promiscuous mode
[   34.927043] device eth1 entered promiscuous mode
[   34.934692] br-lan: port 1(eth1.1) entered blocking state
[   34.936439] br-lan: port 1(eth1.1) entered forwarding state
[   41.497983] ath10k_pci 0000:01:00.0: unsupported HTC service id: 1536
[   41.498205] ath10k_pci 0000:01:00.0: 10.4 wmi init: vdevs: 16  peers: 48  tid: 96
[   41.503397] ath10k_pci 0000:01:00.0: msdu-desc: 2500  skid: 32
[   41.584993] ath10k_pci 0000:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186  msdu-desc: 2500  sw-crypt: 0 ct-sta: 0'
[   41.585841] ath10k_pci 0000:01:00.0: wmi print 'free: 84920 iram: 13316 sram: 11224'
[   41.963081] ath10k_pci 0000:01:00.0: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4
[   41.967364] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[   41.974008] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   41.987847] br-lan: port 2(wlan0) entered blocking state
[   41.987869] br-lan: port 2(wlan0) entered disabled state
[   41.992465] device wlan0 entered promiscuous mode
[   42.158445] ath10k_pci 0000:01:00.0: NOTE:  Firmware DBGLOG output disabled in debug_mask: 0x10000000
[   47.938514] ath10k_pci 0001:01:00.0: unsupported HTC service id: 1536
[   47.939207] ath10k_pci 0001:01:00.0: 10.4 wmi init: vdevs: 16  peers: 48  tid: 96
[   47.943927] ath10k_pci 0001:01:00.0: msdu-desc: 2500  skid: 32
[   48.027595] ath10k_pci 0001:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186  msdu-desc: 2500  sw-crypt: 0 ct-sta: 0'
[   48.028480] ath10k_pci 0001:01:00.0: wmi print 'free: 84920 iram: 13316 sram: 11224'
[   48.642253] ath10k_pci 0001:01:00.0: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4
[   48.665281] br-lan: port 3(wlan1) entered blocking state
[   48.665304] br-lan: port 3(wlan1) entered disabled state
[   48.669905] device wlan1 entered promiscuous mode
[   51.876753] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   51.876889] br-lan: port 2(wlan0) entered blocking state
[   51.882167] br-lan: port 2(wlan0) entered forwarding state
[   59.428462] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[   59.428847] br-lan: port 3(wlan1) entered blocking state
[   59.433926] br-lan: port 3(wlan1) entered forwarding state
[  117.396165] ath10k_pci 0001:01:00.0: wmi: fixing invalid VHT TX rate code 0xff
Aleksandr Mezin commented on 13.11.2020 05:21

For me this is caused by commit https://github.com/openwrt/openwrt/commit/a0be58576cfc25f93f10aabf45908f6056d9f848 (November 12th). Are you sure it didn't work in November 10th snapshot?

Loading...

Available keyboard shortcuts

Tasklist

Task Details

Task Editing