Skip to content
New issue

Have a question about this project? Sign up for a free GitHub account to open an issue and contact its maintainers and the community.

By clicking “Sign up for GitHub”, you agree to our terms of service and privacy statement. We’ll occasionally send you account related emails.

Already on GitHub? Sign in to your account

FS#3405 - ath10k-ct TP-Link EAP245v3 (QCA9982) 5Ghz 802.11ac radio will not TX above 40Mhz width #8262

Open
openwrt-bot opened this issue Oct 24, 2020 · 9 comments
Labels
flyspray kernel pull request/issue with Linux kernel related changes

Comments

@openwrt-bot
Copy link

DoritosVodka:

Model : TP-Link EAP245 v3
Architecture : Qualcomm Atheros QCA956X ver 1 rev 0
Firmware Version : OpenWrt SNAPSHOT r14740-0b31713c85 / LuCI Master git-20.295.56858-2bbde85
Kernel Version : 5.4.72

radio0 : Type: Qualcomm Atheros QCA9990 802.11nac

TP-Link EAP245 v3 spec states it uses a QCA9982 chip. Driver looks to be id'ing the chip as QCA9990.

When using kmod-ath10k-ct Module/Driver. The 5Ghz Radio never goes into 80Mhz width in TX mode, 40Mhz max. The Wireless client list shows TX as 40Mhz and external Spectrum Analyzer verifies the AP radio is only using the "correct" 40Mhz width for TX. Depending on channel used, you can see either the upper or lower 40Mhz width use.

By switching to the Kernel base kmod-ath10k Module/Driver. The Wireless client list always says 6Mb/s 20Mhz for the TX mode. But, testing throughput and watching Spectrum Analyzer actually shows the AP radio is TX'ing at 80Mhz width and higher VHT Rates.

Using the Kernel base or CT Firmware in either combo does not make a difference. But, the CT Firmware seems to have a bit better throughput performance while using either Module/Driver.

Below is Station info Dumps, Device Infos and Boot Log (dmesg) for both Module/Driver usages.
=====Using [ath10k-firmware-qca99x0-ct - 2020-07-02-1 & kmod-ath10k-ct - 5.4.72+2020-06-30-edfbf916-1]=====

root@OpenWrt:# iw dev wlan0 station dump
Station XX:XX:XX:XX:XX:XX (on wlan0)
inactive time: 4 ms
rx bytes: 372464
rx packets: 1978
tx bytes: 551868
tx packets: 1377
tx retries: 4
tx failed: 0
rx drop misc: 0
signal: -40 [-43, -41, -36] dBm
signal avg: -38 [-44, -40, -35] dBm
tx bitrate: 405.0 MBit/s VHT-MCS 6 40MHz short GI VHT-NSS 3
tx duration: 938974 us
rx bitrate: 1300.0 MBit/s VHT-MCS 9 80MHz short GI VHT-NSS 3
rx duration: 0 us
authorized: yes
authenticated: yes
associated: yes
preamble: long
WMM/WME: yes
MFP: no
TDLS peer: no
DTIM period: 2
beacon interval:100
short slot time:yes
connected time: 33 seconds
associated at [boottime]: 312.103s
associated at: 18446725628512616754 ms
current time: 1546824856 ms

root@OpenWrt:# hostapd_cli all_sta
Selected interface 'wlan0'
XX:XX:XX:XX:XX:XX
flags=[AUTH][ASSOC][AUTHORIZED][WMM][HT][VHT]
aid=1
capability=0x1
listen_interval=10
supported_rates=8c 12 98 24 b0 48 60 6c
timeout_next=NULLFUNC POLL
rx_packets=428
tx_packets=324
rx_bytes=75284
tx_bytes=114911
inactive_msec=0
signal=-47
rx_rate_info=240
tx_rate_info=3600 vhtmcs 5 vhtnss 3 shortGI
rx_vht_mcs_map=ffea
tx_vht_mcs_map=ffea
ht_mcs_bitmask=ffffff00000000000000
connected_time=7
min_txpower=2
max_txpower=32
vht_caps_info=0x0f8259b2
ht_caps_info=0x09ef
ext_capab=0400000000000040

root@OpenWrt:# iw dev wlan0 info
Interface wlan0
ifindex 8
wdev 0x2
addr b0:95:75:6d:f0:3d
ssid OpenWrt
type AP
wiphy 0
channel 149 (5745 MHz), width: 80 MHz, center1: 5775 MHz
txpower 20.00 dBm
multicast TXQ:
qsz-byt qsz-pkt flows drops marks overlmt hashcol tx-bytes tx-packets
0 0 0 0 0 0 0 0 0

root@OpenWrt:# iw phy phy0 info
Wiphy phy0
wiphy index: 0
max # scan SSIDs: 16
max scan IEs length: 199 bytes
max # sched scan SSIDs: 0
max # match sets: 0
max # scan plans: 1
max scan plan interval: -1
max scan plan iterations: 0
Retry short limit: 7
Retry long limit: 4
Coverage class: 0 (up to 0m)
Device supports RSN-IBSS.
Device supports AP-side u-APSD.
Supported Ciphers:
* WEP40 (00-0f-ac:1)
* WEP104 (00-0f-ac:5)
* TKIP (00-0f-ac:2)
* CCMP-128 (00-0f-ac:4)
* CMAC (00-0f-ac:6)
* CMAC-256 (00-0f-ac:13)
* GMAC-128 (00-0f-ac:11)
* GMAC-256 (00-0f-ac:12)
* GCMP-128 (00-0f-ac:8)
* GCMP-256 (00-0f-ac:9)
* CCMP-256 (00-0f-ac:10)
Available Antennas: TX 0x7 RX 0x7
Configured Antennas: TX 0x7 RX 0x7
Supported interface modes:
* IBSS
* managed
* AP
* AP/VLAN
* monitor
* mesh point
* P2P-client
* P2P-GO
* P2P-device
Band 2:
Capabilities: 0x19ef
RX LDPC
HT20/HT40
SM Power Save disabled
RX HT20 SGI
RX HT40 SGI
TX STBC
RX STBC 1-stream
Max AMSDU length: 7935 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 8 usec (0x06)
HT TX/RX MCS rate indexes supported: 0-23
VHT Capabilities (0x339a79b2):
Max MPDU length: 11454
Supported Channel Width: neither 160 nor 80+80
RX LDPC
short GI (80 MHz)
TX STBC
SU Beamformer
SU Beamformee
MU Beamformer
MU Beamformee
RX antenna pattern consistency
TX antenna pattern consistency
VHT RX MCS set:
1 streams: MCS 0-9
2 streams: MCS 0-9
3 streams: MCS 0-9
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
VHT RX highest supported: 0 Mbps
VHT TX MCS set:
1 streams: MCS 0-9
2 streams: MCS 0-9
3 streams: MCS 0-9
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
VHT TX highest supported: 0 Mbps
Bitrates (non-HT):
* 6.0 Mbps
* 9.0 Mbps
* 12.0 Mbps
* 18.0 Mbps
* 24.0 Mbps
* 36.0 Mbps
* 48.0 Mbps
* 54.0 Mbps
Frequencies:
* 5180 MHz [36] (23.0 dBm)
* 5200 MHz [40] (23.0 dBm)
* 5220 MHz [44] (23.0 dBm)
* 5240 MHz [48] (23.0 dBm)
* 5260 MHz [52] (23.0 dBm) (radar detection)
* 5280 MHz [56] (23.0 dBm) (radar detection)
* 5300 MHz [60] (23.0 dBm) (radar detection)
* 5320 MHz [64] (23.0 dBm) (radar detection)
* 5500 MHz [100] (23.0 dBm) (radar detection)
* 5520 MHz [104] (23.0 dBm) (radar detection)
* 5540 MHz [108] (23.0 dBm) (radar detection)
* 5560 MHz [112] (23.0 dBm) (radar detection)
* 5580 MHz [116] (23.0 dBm) (radar detection)
* 5600 MHz [120] (23.0 dBm) (radar detection)
* 5620 MHz [124] (23.0 dBm) (radar detection)
* 5640 MHz [128] (23.0 dBm) (radar detection)
* 5660 MHz [132] (23.0 dBm) (radar detection)
* 5680 MHz [136] (23.0 dBm) (radar detection)
* 5700 MHz [140] (23.0 dBm) (radar detection)
* 5720 MHz [144] (23.0 dBm) (radar detection)
* 5745 MHz [149] (30.0 dBm)
* 5765 MHz [153] (30.0 dBm)
* 5785 MHz [157] (30.0 dBm)
* 5805 MHz [161] (30.0 dBm)
* 5825 MHz [165] (30.0 dBm)
* 5845 MHz [169] (disabled)
* 5865 MHz [173] (disabled)
Supported commands:
* new_interface
* set_interface
* new_key
* start_ap
* new_station
* new_mpath
* set_mesh_config
* set_bss
* authenticate
* associate
* deauthenticate
* disassociate
* join_ibss
* join_mesh
* remain_on_channel
* set_tx_bitrate_mask
* frame
* frame_wait_cancel
* set_wiphy_netns
* set_channel
* set_wds_peer
* probe_client
* set_noack_map
* register_beacons
* start_p2p_device
* set_mcast_rate
* testmode
* connect
* disconnect
* channel_switch
* set_qos_map
* set_multicast_to_unicast
Supported TX frame types:
* IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-device: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
Supported RX frame types:
* IBSS: 0x40 0xb0 0xc0 0xd0
* managed: 0x40 0xb0 0xd0
* AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* mesh point: 0xb0 0xc0 0xd0
* P2P-client: 0x40 0xd0
* P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* P2P-device: 0x40 0xd0
software interface modes (can always be added):
* AP/VLAN
* monitor
valid interface combinations:
* #{ managed } <= 16, #{ AP, mesh point } <= 16, #{ IBSS } <= 1,
total <= 16, #channels <= 1, STA/AP BI must match, radar detect widths: { 20 MHz (no HT), 20 MHz, 40 MHz, 80 MHz, 80+80 MHz, 160 MHz }

HT Capability overrides:
	 * MCS: ff ff ff ff ff ff ff ff ff ff
	 * maximum A-MSDU length
	 * supported channel width
	 * short GI for 40 MHz
	 * max A-MPDU length exponent
	 * min MPDU start spacing
Device supports TX status socket option.
Device supports HT-IBSS.
Device supports SAE with AUTHENTICATE command
Device supports scan flush.
Device supports AP scan.
Device supports per-vif TX power setting
Driver supports full state transitions for AP/GO clients
Driver supports a userspace MPM
Driver/device bandwidth changes during BSS lifetime (AP/GO mode)
Device supports static SMPS
Device supports configuring vdev MAC-addr on create.
Maximum associated stations in AP mode: 0
Supported extended features:
	* [ VHT_IBSS ]: VHT-IBSS
	* [ RRM ]: RRM
	* [ SET_SCAN_DWELL ]: scan dwell setting
	* [ CQM_RSSI_LIST ]: multiple CQM_RSSI_THOLD records
	* [ CONTROL_PORT_OVER_NL80211 ]: control port over nl80211
	* [ TXQS ]: FQ-CoDel-enabled intermediate TXQs
	* [ AQL ]: Airtime Queue Limits (AQL)
	* [ CONTROL_PORT_NO_PREAUTH ]: disable pre-auth over nl80211 control port support
	* [ DEL_IBSS_STA ]: deletion of IBSS station support
	* [ SCAN_FREQ_KHZ ]: scan on kHz frequency support
	* [ CONTROL_PORT_OVER_NL80211_TX_STATUS ]: tx status for nl80211 control port support


root@OpenWrt:~# dmesg
[ 0.000000] Linux version 5.4.72 (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r14736-6a56a6eb30)) #0 Thu Oct 22 14:13:38 2020
[ 0.000000] printk: bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019750 (MIPS 74Kc)
[ 0.000000] MIPS: machine is TP-Link EAP245 v3
[ 0.000000] SoC: Qualcomm Atheros QCA956X ver 1 rev 0
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] On node 0 totalpages: 32768
[ 0.000000] Normal zone: 288 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 32768 pages, LIFO batch:7
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=132768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32480
[ 0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,jffs2
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 121672K/131072K available (5052K kernel code, 312K rwdata, 1212K rodata, 1288K init, 206K bss, 9400K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 51
[ 0.000000] random: get_random_bytes called from start_kernel+0x3a4/0x590 with crng_init=0
[ 0.000000] CPU clock: 775.000 MHz
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4932285024 ns
[ 0.000007] sched_clock: 32 bits at 387MHz, resolution 2ns, wraps every 5541893118ns
[ 0.008219] Calibrating delay loop... 385.02 BogoMIPS (lpj=770048)
[ 0.046722] pid_max: default: 32768 minimum: 301
[ 0.051723] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.059434] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.071487] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.081799] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[ 0.089092] pinctrl core: initialized pinctrl subsystem
[ 0.095574] NET: Registered protocol family 16
[ 0.127640] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512
[ 0.140856] clocksource: Switched to clocksource MIPS
[ 0.181151] NET: Registered protocol family 2
[ 0.186456] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.195337] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.203434] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.210882] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.217712] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.224649] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.232285] NET: Registered protocol family 1
[ 0.236952] PCI: CLS 0 bytes, default 32
[ 0.244535] workingset: timestamp_bits=14 max_order=15 bucket_order=1
[ 0.257536] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.263728] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.288911] pinctrl-single 1804002c.pinmux: 544 pins, size 68
[ 0.295954] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.303355] printk: console [ttyS0] disabled
[ 0.307945] 18020000.uart: ttyS0 at MMIO 0x18020000 (irq = 9, base_baud = 1562500) is a 16550A
[ 0.317053] printk: console [ttyS0] enabled
[ 0.326113] printk: bootconsole [early0] disabled
[ 0.351896] spi-nor spi0.0: w25q128 (16384 Kbytes)
[ 0.356934] 10 fixed-partitions partitions found on MTD device spi0.0
[ 0.363599] Creating 10 MTD partitions on "spi0.0":
[ 0.368667] 0x000000000000-0x000000040000 : "factory-boot"
[ 0.375225] 0x000000040000-0x000000080000 : "u-boot"
[ 0.381335] 0x000000080000-0x000000090000 : "partition-table"
[ 0.388164] 0x000000090000-0x0000000a0000 : "info"
[ 0.394006] 0x0000000a0000-0x0000000b0000 : "art"
[ 0.399746] 0x0000000b0000-0x0000000c0000 : "extra-para"
[ 0.406163] 0x0000000c0000-0x000000f00000 : "firmware"
[ 0.417720] 2 elf-loader-fw partitions found on MTD device firmware
[ 0.424248] Creating 2 MTD partitions on "firmware":
[ 0.429400] 0x000000000000-0x000000210000 : "kernel"
[ 0.435417] 0x000000210000-0x000000e40000 : "rootfs"
[ 0.441473] mtd: device 8 (rootfs) set to be root filesystem
[ 0.449158] 1 squashfs-split partitions found on MTD device rootfs
[ 0.455596] 0x0000005d0000-0x000000e40000 : "rootfs_data"
[ 0.462049] 0x000000f00000-0x000000f30000 : "config"
[ 0.468096] 0x000000f30000-0x000000fb0000 : "mutil-log"
[ 0.474388] 0x000000fb0000-0x000000ff0000 : "oops"
[ 0.482101] libphy: Fixed MDIO Bus: probed
[ 1.137235] libphy: ag71xx_mdio: probed
[ 1.142929] switch0: Atheros AR8337 rev. 2 switch registered on mdio.0
[ 1.152880] random: fast init done
[ 1.721331] ag71xx 19000000.eth: connected to PHY at mdio.0:00 [uid=004dd036, driver=Atheros AR8216/AR8236/AR8316]
[ 1.732601] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode: sgmii
[ 1.739214] i2c /dev entries driver
[ 1.744588] NET: Registered protocol family 10
[ 1.753750] Segment Routing with IPv6
[ 1.757690] NET: Registered protocol family 17
[ 1.762365] 8021q: 802.1Q VLAN Support v1.8
[ 1.767443] PCI host bridge /ahb/pcie-controller@18250000 ranges:
[ 1.773814] MEM 0x0000000012000000..0x0000000013ffffff
[ 1.779227] IO 0x0000000000000000..0x0000000000000000
[ 1.784797] PCI host bridge to bus 0000:00
[ 1.789074] pci_bus 0000:00: root bus resource [mem 0x12000000-0x13ffffff]
[ 1.796185] pci_bus 0000:00: root bus resource [io 0x0000]
[ 1.801946] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 1.808962] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 1.817175] pci 0000:00:00.0: [168c:0040] type 00 class 0x028000
[ 1.823442] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[ 1.830593] pci 0000:00:00.0: PME# supported from D0 D3hot D3cold
[ 1.836927] pci 0000:00:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5 GT/s x1 link)
[ 1.852054] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 1.858936] pci 0000:00:00.0: BAR 0: assigned [mem 0x12000000-0x121fffff 64bit]
[ 1.872041] VFS: Mounted root (squashfs filesystem) readonly on device 31:8.
[ 1.886624] Freeing unused kernel memory: 1288K
[ 1.891332] This architecture does not have kernel memory protection.
[ 1.897983] Run /sbin/init as init process
[ 2.529841] init: Console is alive
[ 2.533676] init: - watchdog -
[ 3.641876] kmodloader: loading kernel modules from /etc/modules-boot.d/

[ 3.799509] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 3.817441] init: - preinit -
[ 4.823650] random: jshn: uninitialized urandom read (4 bytes read)
[ 4.928057] random: jshn: uninitialized urandom read (4 bytes read)
[ 5.027609] random: jshn: uninitialized urandom read (4 bytes read)
[ 6.134756] Atheros AR8216/AR8236/AR8316 mdio.0:00: Port 2 is up
[ 6.148545] eth0: link up (1000Mbps/Full duplex)
[ 6.161906] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 6.177015] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
[ 6.213179] urandom_read: 4 callbacks suppressed
[ 6.213186] random: procd: uninitialized urandom read (4 bytes read)
[ 10.447678] jffs2: notice: (533) jffs2_build_xattr_subsystem: complete building xattr subsystem, 22 of xdatum (18 unchecked, 4 orphan) and 31 of xref (4 dead, 0 orphan) found.
[ 10.466239] mount_root: switching to jffs2 overlay
[ 10.475385] overlayfs: upper fs does not support tmpfile.
[ 10.485765] urandom-seed: Seeding with /etc/urandom.seed
[ 10.586510] eth0: link down
[ 10.608144] procd: - early -
[ 10.611280] procd: - watchdog -
[ 11.232608] procd: - watchdog -
[ 11.236186] procd: - ubus -
[ 11.384760] random: ubusd: uninitialized urandom read (4 bytes read)
[ 11.392328] random: ubusd: uninitialized urandom read (4 bytes read)
[ 11.400337] procd: - init -
[ 12.433915] urngd: v1.0.2 started.
[ 12.550359] kmodloader: loading kernel modules from /etc/modules.d/*
[ 12.597093] Loading modules backported from Linux version v5.8-0-gbcf876870b95
[ 12.604596] Backport generated by backports.git v5.8-1-0-g79400d9e
[ 12.668910] xt_time: kernel timezone is -0000
[ 12.693678] random: crng init done
[ 13.081029] PPP generic driver version 2.4.2
[ 13.094232] NET: Registered protocol family 24
[ 14.239275] ath10k 5.4 driver, optimized for CT firmware, probing pci device: 0x40.
[ 14.247374] ath10k_mac_create, priv_size: 804 hw: 97bf64b5 hw->priv: c7d00963
[ 14.257806] ath10k_pci 0000:00:00.0: enabling device (0000 -> 0002)
[ 14.264596] ath10k_pci 0000:00:00.0: pci irq legacy oper_irq_mode 1 irq_mode 0 reset_mode 0
[ 16.036920] ath10k_pci 0000:00:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003b01ff sub 168c:0002
[ 16.046471] ath10k_pci 0000:00:00.0: kconfig debug 1 debugfs 1 tracing 0 dfs 1 testmode 0
[ 16.065270] ath10k_pci 0000:00:00.0: firmware ver 10.4b-ct-9980-fW-13-10af6a005 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 4a0fa880
[ 16.162208] ath10k_pci 0000:00:00.0: board_file api 2 bmi_id 1:1 crc32 08fa09f2
[ 17.353958] ath10k_pci 0000:00:00.0: unsupported HTC service id: 1536
[ 17.364779] ath10k_pci 0000:00:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
[ 17.372550] ath10k_pci 0000:00:00.0: msdu-desc: 2500 skid: 32
[ 17.448463] ath10k_pci 0000:00:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
[ 17.459794] ath10k_pci 0000:00:00.0: wmi print 'free: 31080 iram: 23092 sram: 9596'
[ 17.722487] ath10k_pci 0000:00:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1
[ 17.805953] ath: EEPROM regdomain sanitized
[ 17.805962] ath: EEPROM regdomain: 0x64
[ 17.805966] ath: EEPROM indicates we should expect a direct regpair map
[ 17.805984] ath: Country alpha2 being used: 00
[ 17.805987] ath: Regpair used: 0x64
[ 17.923779] ath: EEPROM regdomain sanitized
[ 17.923789] ath: EEPROM regdomain: 0x64
[ 17.923792] ath: EEPROM indicates we should expect a direct regpair map
[ 17.923811] ath: Country alpha2 being used: 00
[ 17.923814] ath: Regpair used: 0x64
[ 17.936067] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[ 17.939540] ieee80211 phy1: Atheros AR9561 Rev:0 mem=0xb8100000, irq=2
[ 18.018840] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 30.128185] eth0: link up (1000Mbps/Full duplex)
[ 30.146897] br-lan: port 1(eth0.1) entered blocking state
[ 30.152534] br-lan: port 1(eth0.1) entered disabled state
[ 30.158435] device eth0.1 entered promiscuous mode
[ 30.163431] device eth0 entered promiscuous mode
[ 30.221011] br-lan: port 1(eth0.1) entered blocking state
[ 30.226621] br-lan: port 1(eth0.1) entered forwarding state
[ 31.149494] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 31.156565] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 32.009921] ath: EEPROM regdomain: 0x8348
[ 32.009929] ath: EEPROM indicates we should expect a country code
[ 32.009935] ath: doing EEPROM country->regdmn map search
[ 32.009941] ath: country maps to regdmn code: 0x3a
[ 32.009945] ath: Country alpha2 being used: US
[ 32.009948] ath: Regpair used: 0x3a
[ 32.009954] ath: regdomain 0x8348 dynamically updated by user
[ 32.010026] ath: EEPROM regdomain: 0x8348
[ 32.010029] ath: EEPROM indicates we should expect a country code
[ 32.010034] ath: doing EEPROM country->regdmn map search
[ 32.010039] ath: country maps to regdmn code: 0x3a
[ 32.010042] ath: Country alpha2 being used: US
[ 32.010045] ath: Regpair used: 0x3a
[ 32.010049] ath: regdomain 0x8348 dynamically updated by user
[ 34.709097] ath10k_pci 0000:00:00.0: unsupported HTC service id: 1536
[ 34.716489] ath10k_pci 0000:00:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
[ 34.724287] ath10k_pci 0000:00:00.0: msdu-desc: 2500 skid: 32
[ 34.800204] ath10k_pci 0000:00:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
[ 34.811528] ath10k_pci 0000:00:00.0: wmi print 'free: 31080 iram: 23092 sram: 9596'
[ 35.239194] ath10k_pci 0000:00:00.0: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4
[ 35.257261] br-lan: port 2(wlan0) entered blocking state
[ 35.262803] br-lan: port 2(wlan0) entered disabled state
[ 35.268627] device wlan0 entered promiscuous mode
[ 35.278233] ath10k_pci 0000:00:00.0: NOTE: Firmware DBGLOG output disabled in debug_mask: 0x10000000
[ 35.868492] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 35.875316] br-lan: port 2(wlan0) entered blocking state
[ 35.880867] br-lan: port 2(wlan0) entered forwarding state
[ 35.970076] ath10k_pci 0000:00:00.0: wmi: fixing invalid VHT TX rate code 0xff

=====Using [ath10k-firmware-qca99x0-ct - 2020-07-02-1 & kmod-ath10k - 5.4.72+5.8-1-1]=====

root@OpenWrt:# iw dev wlan0 station dump
Station XX:XX:XX:XX:XX:XX (on wlan0)
inactive time: 4 ms
rx bytes: 565899
rx packets: 3118
tx bytes: 780134
tx packets: 2370
tx retries: 0
tx failed: 0
rx drop misc: 0
signal: -42 [-50, -48, -45] dBm
signal avg: -40 [-47, -45, -42] dBm
tx bitrate: 6.0 MBit/s
tx duration: 1393575 us
rx bitrate: 1300.0 MBit/s VHT-MCS 9 80MHz short GI VHT-NSS 3
rx duration: 0 us
authorized: yes
authenticated: yes
associated: yes
preamble: long
WMM/WME: yes
MFP: no
TDLS peer: no
DTIM period: 2
beacon interval:100
short slot time:yes
connected time: 67 seconds
associated at [boottime]: 4685.320s
associated at: 18446725628516418838 ms
current time: 1546257928 ms

root@OpenWrt:# hostapd_cli all_sta
Selected interface 'wlan0'
XX:XX:XX:XX:XX:XX
flags=[AUTH][ASSOC][AUTHORIZED][WMM][HT][VHT]
aid=1
capability=0x1
listen_interval=10
supported_rates=8c 12 98 24 b0 48 60 6c
timeout_next=NULLFUNC POLL
rx_packets=3951
tx_packets=3058
rx_bytes=745151
tx_bytes=1173711
inactive_msec=4
signal=-52
rx_rate_info=8775 vhtmcs 7 vhtnss 3
tx_rate_info=60
rx_vht_mcs_map=ffea
tx_vht_mcs_map=ffea
ht_mcs_bitmask=ffffff00000000000000
connected_time=80
min_txpower=2
max_txpower=32
vht_caps_info=0x0f8259b2
ht_caps_info=0x09ef
ext_capab=0400000000000040

root@OpenWrt:# iw dev wlan0 info
Interface wlan0
ifindex 11
wdev 0x5
addr b0:95:75:6d:f0:3d
ssid OpenWrt
type AP
wiphy 0
channel 149 (5745 MHz), width: 80 MHz, center1: 5775 MHz
txpower 20.00 dBm
multicast TXQ:
qsz-byt qsz-pkt flows drops marks overlmt hashcol tx-bytes tx-packets
0 0 0 0 0 0 0 0 0

root@OpenWrt:# iw phy phy0 info
Wiphy phy0
wiphy index: 0
max # scan SSIDs: 16
max scan IEs length: 199 bytes
max # sched scan SSIDs: 0
max # match sets: 0
max # scan plans: 1
max scan plan interval: -1
max scan plan iterations: 0
Retry short limit: 7
Retry long limit: 4
Coverage class: 0 (up to 0m)
Device supports RSN-IBSS.
Device supports AP-side u-APSD.
Supported Ciphers:
* WEP40 (00-0f-ac:1)
* WEP104 (00-0f-ac:5)
* TKIP (00-0f-ac:2)
* CCMP-128 (00-0f-ac:4)
* CMAC (00-0f-ac:6)
* CMAC-256 (00-0f-ac:13)
* GMAC-128 (00-0f-ac:11)
* GMAC-256 (00-0f-ac:12)
* GCMP-128 (00-0f-ac:8)
* GCMP-256 (00-0f-ac:9)
* CCMP-256 (00-0f-ac:10)
Available Antennas: TX 0x7 RX 0x7
Configured Antennas: TX 0x7 RX 0x7
Supported interface modes:
* managed
* AP
* AP/VLAN
* monitor
* mesh point
* P2P-client
* P2P-GO
* P2P-device
Band 2:
Capabilities: 0x19ef
RX LDPC
HT20/HT40
SM Power Save disabled
RX HT20 SGI
RX HT40 SGI
TX STBC
RX STBC 1-stream
Max AMSDU length: 7935 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 8 usec (0x06)
HT TX/RX MCS rate indexes supported: 0-23
VHT Capabilities (0x339a79b2):
Max MPDU length: 11454
Supported Channel Width: neither 160 nor 80+80
RX LDPC
short GI (80 MHz)
TX STBC
SU Beamformer
SU Beamformee
MU Beamformer
MU Beamformee
RX antenna pattern consistency
TX antenna pattern consistency
VHT RX MCS set:
1 streams: MCS 0-9
2 streams: MCS 0-9
3 streams: MCS 0-9
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
VHT RX highest supported: 0 Mbps
VHT TX MCS set:
1 streams: MCS 0-9
2 streams: MCS 0-9
3 streams: MCS 0-9
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
VHT TX highest supported: 0 Mbps
Bitrates (non-HT):
* 6.0 Mbps
* 9.0 Mbps
* 12.0 Mbps
* 18.0 Mbps
* 24.0 Mbps
* 36.0 Mbps
* 48.0 Mbps
* 54.0 Mbps
Frequencies:
* 5180 MHz [36] (23.0 dBm)
* 5200 MHz [40] (23.0 dBm)
* 5220 MHz [44] (23.0 dBm)
* 5240 MHz [48] (23.0 dBm)
* 5260 MHz [52] (23.0 dBm) (radar detection)
* 5280 MHz [56] (23.0 dBm) (radar detection)
* 5300 MHz [60] (23.0 dBm) (radar detection)
* 5320 MHz [64] (23.0 dBm) (radar detection)
* 5500 MHz [100] (23.0 dBm) (radar detection)
* 5520 MHz [104] (23.0 dBm) (radar detection)
* 5540 MHz [108] (23.0 dBm) (radar detection)
* 5560 MHz [112] (23.0 dBm) (radar detection)
* 5580 MHz [116] (23.0 dBm) (radar detection)
* 5600 MHz [120] (23.0 dBm) (radar detection)
* 5620 MHz [124] (23.0 dBm) (radar detection)
* 5640 MHz [128] (23.0 dBm) (radar detection)
* 5660 MHz [132] (23.0 dBm) (radar detection)
* 5680 MHz [136] (23.0 dBm) (radar detection)
* 5700 MHz [140] (23.0 dBm) (radar detection)
* 5720 MHz [144] (23.0 dBm) (radar detection)
* 5745 MHz [149] (30.0 dBm)
* 5765 MHz [153] (30.0 dBm)
* 5785 MHz [157] (30.0 dBm)
* 5805 MHz [161] (30.0 dBm)
* 5825 MHz [165] (30.0 dBm)
* 5845 MHz [169] (disabled)
* 5865 MHz [173] (disabled)
Supported commands:
* new_interface
* set_interface
* new_key
* start_ap
* new_station
* new_mpath
* set_mesh_config
* set_bss
* authenticate
* associate
* deauthenticate
* disassociate
* join_ibss
* join_mesh
* remain_on_channel
* set_tx_bitrate_mask
* frame
* frame_wait_cancel
* set_wiphy_netns
* set_channel
* set_wds_peer
* probe_client
* set_noack_map
* register_beacons
* start_p2p_device
* set_mcast_rate
* testmode
* connect
* disconnect
* channel_switch
* set_qos_map
* set_multicast_to_unicast
Supported TX frame types:
* IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-device: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
Supported RX frame types:
* IBSS: 0x40 0xb0 0xc0 0xd0
* managed: 0x40 0xb0 0xd0
* AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* mesh point: 0xb0 0xc0 0xd0
* P2P-client: 0x40 0xd0
* P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* P2P-device: 0x40 0xd0
software interface modes (can always be added):
* AP/VLAN
* monitor
valid interface combinations:
* #{ managed } <= 1, #{ AP, mesh point } <= 16,
total <= 16, #channels <= 1, STA/AP BI must match, radar detect widths: { 20 MHz (no HT), 20 MHz, 40 MHz, 80 MHz, 80+80 MHz, 160 MHz }

HT Capability overrides:
	 * MCS: ff ff ff ff ff ff ff ff ff ff
	 * maximum A-MSDU length
	 * supported channel width
	 * short GI for 40 MHz
	 * max A-MPDU length exponent
	 * min MPDU start spacing
Device supports TX status socket option.
Device supports HT-IBSS.
Device supports SAE with AUTHENTICATE command
Device supports scan flush.
Device supports AP scan.
Device supports per-vif TX power setting
Driver supports full state transitions for AP/GO clients
Driver supports a userspace MPM
Driver/device bandwidth changes during BSS lifetime (AP/GO mode)
Device supports static SMPS
Device supports configuring vdev MAC-addr on create.
Maximum associated stations in AP mode: 0
Supported extended features:
	* [ VHT_IBSS ]: VHT-IBSS
	* [ RRM ]: RRM
	* [ SET_SCAN_DWELL ]: scan dwell setting
	* [ CQM_RSSI_LIST ]: multiple CQM_RSSI_THOLD records
	* [ CONTROL_PORT_OVER_NL80211 ]: control port over nl80211
	* [ TXQS ]: FQ-CoDel-enabled intermediate TXQs
	* [ AQL ]: Airtime Queue Limits (AQL)
	* [ CONTROL_PORT_NO_PREAUTH ]: disable pre-auth over nl80211 control port support
	* [ SCAN_FREQ_KHZ ]: scan on kHz frequency support
	* [ CONTROL_PORT_OVER_NL80211_TX_STATUS ]: tx status for nl80211 control port support


root@OpenWrt:~# dmesg
[ 0.000000] Linux version 5.4.72 (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r14736-6a56a6eb30)) #0 Thu Oct 22 14:13:38 2020
[ 0.000000] printk: bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019750 (MIPS 74Kc)
[ 0.000000] MIPS: machine is TP-Link EAP245 v3
[ 0.000000] SoC: Qualcomm Atheros QCA956X ver 1 rev 0
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] On node 0 totalpages: 32768
[ 0.000000] Normal zone: 288 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 32768 pages, LIFO batch:7
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=132768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32480
[ 0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,jffs2
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 121672K/131072K available (5052K kernel code, 312K rwdata, 1212K rodata, 1288K init, 206K bss, 9400K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 51
[ 0.000000] random: get_random_bytes called from start_kernel+0x3a4/0x590 with crng_init=0
[ 0.000000] CPU clock: 775.000 MHz
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4932285024 ns
[ 0.000007] sched_clock: 32 bits at 387MHz, resolution 2ns, wraps every 5541893118ns
[ 0.008221] Calibrating delay loop... 385.02 BogoMIPS (lpj=770048)
[ 0.046723] pid_max: default: 32768 minimum: 301
[ 0.051724] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.059435] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.071493] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.081807] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[ 0.089101] pinctrl core: initialized pinctrl subsystem
[ 0.095580] NET: Registered protocol family 16
[ 0.127598] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512
[ 0.140855] clocksource: Switched to clocksource MIPS
[ 0.181150] NET: Registered protocol family 2
[ 0.186456] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.195329] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.203425] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.210874] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.217704] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.224641] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.232277] NET: Registered protocol family 1
[ 0.236944] PCI: CLS 0 bytes, default 32
[ 0.244573] workingset: timestamp_bits=14 max_order=15 bucket_order=1
[ 0.257559] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.263754] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.288814] pinctrl-single 1804002c.pinmux: 544 pins, size 68
[ 0.295899] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.303303] printk: console [ttyS0] disabled
[ 0.307896] 18020000.uart: ttyS0 at MMIO 0x18020000 (irq = 9, base_baud = 1562500) is a 16550A
[ 0.317005] printk: console [ttyS0] enabled
[ 0.326063] printk: bootconsole [early0] disabled
[ 0.351819] spi-nor spi0.0: w25q128 (16384 Kbytes)
[ 0.356868] 10 fixed-partitions partitions found on MTD device spi0.0
[ 0.363526] Creating 10 MTD partitions on "spi0.0":
[ 0.368591] 0x000000000000-0x000000040000 : "factory-boot"
[ 0.375148] 0x000000040000-0x000000080000 : "u-boot"
[ 0.381258] 0x000000080000-0x000000090000 : "partition-table"
[ 0.388084] 0x000000090000-0x0000000a0000 : "info"
[ 0.393927] 0x0000000a0000-0x0000000b0000 : "art"
[ 0.399672] 0x0000000b0000-0x0000000c0000 : "extra-para"
[ 0.406085] 0x0000000c0000-0x000000f00000 : "firmware"
[ 0.417643] 2 elf-loader-fw partitions found on MTD device firmware
[ 0.424171] Creating 2 MTD partitions on "firmware":
[ 0.429325] 0x000000000000-0x000000210000 : "kernel"
[ 0.435349] 0x000000210000-0x000000e40000 : "rootfs"
[ 0.441411] mtd: device 8 (rootfs) set to be root filesystem
[ 0.449077] 1 squashfs-split partitions found on MTD device rootfs
[ 0.455516] 0x0000005d0000-0x000000e40000 : "rootfs_data"
[ 0.461967] 0x000000f00000-0x000000f30000 : "config"
[ 0.468013] 0x000000f30000-0x000000fb0000 : "mutil-log"
[ 0.474308] 0x000000fb0000-0x000000ff0000 : "oops"
[ 0.482014] libphy: Fixed MDIO Bus: probed
[ 1.137237] libphy: ag71xx_mdio: probed
[ 1.142935] switch0: Atheros AR8337 rev. 2 switch registered on mdio.0
[ 1.152879] random: fast init done
[ 1.721333] ag71xx 19000000.eth: connected to PHY at mdio.0:00 [uid=004dd036, driver=Atheros AR8216/AR8236/AR8316]
[ 1.732602] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode: sgmii
[ 1.739209] i2c /dev entries driver
[ 1.744590] NET: Registered protocol family 10
[ 1.753757] Segment Routing with IPv6
[ 1.757694] NET: Registered protocol family 17
[ 1.762371] 8021q: 802.1Q VLAN Support v1.8
[ 1.767446] PCI host bridge /ahb/pcie-controller@18250000 ranges:
[ 1.773809] MEM 0x0000000012000000..0x0000000013ffffff
[ 1.779224] IO 0x0000000000000000..0x0000000000000000
[ 1.784793] PCI host bridge to bus 0000:00
[ 1.789069] pci_bus 0000:00: root bus resource [mem 0x12000000-0x13ffffff]
[ 1.796181] pci_bus 0000:00: root bus resource [io 0x0000]
[ 1.801950] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 1.808966] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 1.817181] pci 0000:00:00.0: [168c:0040] type 00 class 0x028000
[ 1.823446] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[ 1.830596] pci 0000:00:00.0: PME# supported from D0 D3hot D3cold
[ 1.836932] pci 0000:00:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5 GT/s x1 link)
[ 1.852061] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 1.858949] pci 0000:00:00.0: BAR 0: assigned [mem 0x12000000-0x121fffff 64bit]
[ 1.872068] VFS: Mounted root (squashfs filesystem) readonly on device 31:8.
[ 1.886654] Freeing unused kernel memory: 1288K
[ 1.891354] This architecture does not have kernel memory protection.
[ 1.898004] Run /sbin/init as init process
[ 2.529873] init: Console is alive
[ 2.533706] init: - watchdog -
[ 3.643607] kmodloader: loading kernel modules from /etc/modules-boot.d/

[ 3.802387] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 3.820321] init: - preinit -
[ 4.827578] random: jshn: uninitialized urandom read (4 bytes read)
[ 4.931977] random: jshn: uninitialized urandom read (4 bytes read)
[ 5.031419] random: jshn: uninitialized urandom read (4 bytes read)
[ 6.131039] Atheros AR8216/AR8236/AR8316 mdio.0:00: Port 2 is up
[ 6.144914] eth0: link up (1000Mbps/Full duplex)
[ 6.158221] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 6.172985] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
[ 6.209112] urandom_read: 4 callbacks suppressed
[ 6.209119] random: procd: uninitialized urandom read (4 bytes read)
[ 10.439008] jffs2: notice: (533) jffs2_build_xattr_subsystem: complete building xattr subsystem, 18 of xdatum (15 unchecked, 3 orphan) and 26 of xref (3 dead, 0 orphan) found.
[ 10.457361] mount_root: switching to jffs2 overlay
[ 10.466432] overlayfs: upper fs does not support tmpfile.
[ 10.476910] urandom-seed: Seeding with /etc/urandom.seed
[ 10.577395] eth0: link down
[ 10.599006] procd: - early -
[ 10.602144] procd: - watchdog -
[ 11.223676] procd: - watchdog -
[ 11.227261] procd: - ubus -
[ 11.375979] random: ubusd: uninitialized urandom read (4 bytes read)
[ 11.383540] random: ubusd: uninitialized urandom read (4 bytes read)
[ 11.391593] procd: - init -
[ 12.153939] kmodloader: loading kernel modules from /etc/modules.d/*
[ 12.201002] Loading modules backported from Linux version v5.8-0-gbcf876870b95
[ 12.208495] Backport generated by backports.git v5.8-1-0-g79400d9e
[ 12.271793] xt_time: kernel timezone is -0000
[ 12.606386] urngd: v1.0.2 started.
[ 12.668904] PPP generic driver version 2.4.2
[ 12.682215] NET: Registered protocol family 24
[ 12.773573] ath10k_pci 0000:00:00.0: enabling device (0000 -> 0002)
[ 12.780355] ath10k_pci 0000:00:00.0: pci irq legacy oper_irq_mode 1 irq_mode 0 reset_mode 0
[ 12.826696] random: crng init done
[ 14.665264] ath10k_pci 0000:00:00.0: Unknown FW IE: 30
[ 14.670637] ath10k_pci 0000:00:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003b01ff sub 168c:0002
[ 14.680175] ath10k_pci 0000:00:00.0: kconfig debug 1 debugfs 1 tracing 1 dfs 1 testmode 1
[ 14.698951] ath10k_pci 0000:00:00.0: firmware ver 10.4b-ct-9980-fW-13-10af6a005 api 5 features mfp,peer-flow-ctrl crc32 4a0fa880
[ 14.778343] ath10k_pci 0000:00:00.0: board_file api 2 bmi_id 1:1 crc32 08fa09f2
[ 16.035965] ath10k_pci 0000:00:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1
[ 16.121972] ath: EEPROM regdomain sanitized
[ 16.121981] ath: EEPROM regdomain: 0x64
[ 16.121985] ath: EEPROM indicates we should expect a direct regpair map
[ 16.122003] ath: Country alpha2 being used: 00
[ 16.122006] ath: Regpair used: 0x64
[ 16.245810] ath: EEPROM regdomain sanitized
[ 16.245821] ath: EEPROM regdomain: 0x64
[ 16.245824] ath: EEPROM indicates we should expect a direct regpair map
[ 16.245844] ath: Country alpha2 being used: 00
[ 16.245847] ath: Regpair used: 0x64
[ 16.258068] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[ 16.261529] ieee80211 phy1: Atheros AR9561 Rev:0 mem=0xb8100000, irq=2
[ 16.335237] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 28.438682] eth0: link up (1000Mbps/Full duplex)
[ 28.453220] br-lan: port 1(eth0.1) entered blocking state
[ 28.458848] br-lan: port 1(eth0.1) entered disabled state
[ 28.464742] device eth0.1 entered promiscuous mode
[ 28.469734] device eth0 entered promiscuous mode
[ 28.528522] br-lan: port 1(eth0.1) entered blocking state
[ 28.534153] br-lan: port 1(eth0.1) entered forwarding state
[ 29.453481] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 29.460549] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 30.281854] ath: EEPROM regdomain: 0x8348
[ 30.281861] ath: EEPROM indicates we should expect a country code
[ 30.281867] ath: doing EEPROM country->regdmn map search
[ 30.281873] ath: country maps to regdmn code: 0x3a
[ 30.281877] ath: Country alpha2 being used: US
[ 30.281880] ath: Regpair used: 0x3a
[ 30.281886] ath: regdomain 0x8348 dynamically updated by user
[ 30.281959] ath: EEPROM regdomain: 0x8348
[ 30.281961] ath: EEPROM indicates we should expect a country code
[ 30.281967] ath: doing EEPROM country->regdmn map search
[ 30.281972] ath: country maps to regdmn code: 0x3a
[ 30.281975] ath: Country alpha2 being used: US
[ 30.281978] ath: Regpair used: 0x3a
[ 30.281981] ath: regdomain 0x8348 dynamically updated by user
[ 33.720640] br-lan: port 2(wlan0) entered blocking state
[ 33.726187] br-lan: port 2(wlan0) entered disabled state
[ 33.731993] device wlan0 entered promiscuous mode
[ 34.427932] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 34.434737] br-lan: port 2(wlan0) entered blocking state
[ 34.440284] br-lan: port 2(wlan0) entered forwarding state

@openwrt-bot
Copy link
Author

tiagofreire-pt:

I have the same issues, using all the firmwares available, non-CT, CT and CT-HTT.

EA7500 V1, using the current snapshots.

@openwrt-bot
Copy link
Author

greearb:

To make sure I understand: Changing only the driver fixes the problem. Changing the firmware has no great affect either way? If so, for the problem case where you are using the -ct firmware, please enable DBGLOG logging and paste the full dmesg that includes the client association steps. http://www.candelatech.com/ath10k-bugs.php

@openwrt-bot
Copy link
Author

tiagofreire-pt:

cat /sys/kernel/debug/ieee80211/phy1/ath10k/debug_level
Current debug level: 0xc0000030


# dmesg
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 5.4.75 (builder@buildhost) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r14954-aafbfc6ac3)) #0 SMP Mon Nov 16 18:26:25 2020
[ 0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5787d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[ 0.000000] OF: fdt: Machine model: Linksys EA7500 V1 WiFi Router
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] On node 0 totalpages: 57344
[ 0.000000] Normal zone: 504 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 57344 pages, LIFO batch:15
[ 0.000000] percpu: Embedded 15 pages/cpu s30156 r8192 d23092 u61440
[ 0.000000] pcpu-alloc: s30156 r8192 d23092 u61440 alloc=154096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 56840
[ 0.000000] Kernel command line: console=ttyMSM0,115200n8 ubi.mtd=14
[ 0.000000] Bootloader command line (ignored): console=ttyHSL1,115200n8 init=/sbin/init rootfstype=squashfs ubi.mtd=14,2048 ubi.block=0,0 root=/dev/ubiblock0_0 rootwait ro
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 217236K/229376K available (6167K kernel code, 196K rwdata, 1548K rodata, 1024K init, 240K bss, 12140K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] random: get_random_bytes called from start_kernel+0x340/0x4ec with crng_init=0
[ 0.000000] clocksource: dg_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 305801671480 ns
[ 0.000008] sched_clock: 32 bits at 6MHz, resolution 160ns, wraps every 343597383600ns
[ 0.000021] Switching to timer-based delay loop, resolution 160ns
[ 0.000258] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.50 BogoMIPS (lpj=62500)
[ 0.000280] pid_max: default: 32768 minimum: 301
[ 0.000475] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.000496] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.001529] CPU: Testing write buffer coherency: ok
[ 0.002697] Setting up static identity map for 0x42300000 - 0x42300060
[ 0.002879] rcu: Hierarchical SRCU implementation.
[ 0.003375] smp: Bringing up secondary CPUs ...
[ 0.005310] smp: Brought up 1 node, 2 CPUs
[ 0.005330] SMP: Total of 2 processors activated (25.00 BogoMIPS).
[ 0.005341] CPU: All CPU(s) started in SVC mode.
[ 0.015576] VFP support v0.3: implementor 51 architecture 64 part 4d variant 2 rev 0
[ 0.015734] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.015763] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[ 0.015928] pinctrl core: initialized pinctrl subsystem
[ 0.017110] NET: Registered protocol family 16
[ 0.017427] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.018797] cpuidle: using governor ladder
[ 0.018869] cpuidle: using governor menu
[ 0.050346] usbcore: registered new interface driver usbfs
[ 0.050441] usbcore: registered new interface driver hub
[ 0.050528] usbcore: registered new device driver usb
[ 0.050589] pps_core: LinuxPPS API ver. 1 registered
[ 0.050603] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti giometti@linux.it
[ 0.050641] PTP clock support registered
[ 0.051419] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512
[ 0.052692] clocksource: Switched to clocksource dg_timer
[ 0.053610] thermal_sys: Registered thermal governor 'step_wise'
[ 0.056024] NET: Registered protocol family 2
[ 0.056774] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[ 0.056813] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.056846] TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.056897] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.057004] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.057035] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.057263] NET: Registered protocol family 1
[ 0.057317] PCI: CLS 0 bytes, default 64
[ 0.058659] workingset: timestamp_bits=14 max_order=16 bucket_order=2
[ 0.065691] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.065711] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.103944] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[ 0.105782] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda not found, using dummy regulator
[ 0.105932] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda_phy not found, using dummy regulator
[ 0.106041] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda_refclk not found, using dummy regulator
[ 0.106314] qcom-pcie 1b500000.pci: host bridge /soc/pci@1b500000 ranges:
[ 0.106339] qcom-pcie 1b500000.pci: Parsing ranges property...
[ 0.106386] qcom-pcie 1b500000.pci: IO 0x0fe00000..0x0fefffff -> 0x0fe00000
[ 0.106425] qcom-pcie 1b500000.pci: MEM 0x08000000..0x0fdfffff -> 0x08000000
[ 0.328377] qcom-pcie 1b500000.pci: Link up
[ 0.328551] qcom-pcie 1b500000.pci: PCI host bridge to bus 0000:00
[ 0.328574] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.328595] pci_bus 0000:00: root bus resource [io 0x0000-0xfffff] (bus address [0xfe00000-0xfefffff])
[ 0.328612] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fdfffff]
[ 0.328629] pci_bus 0000:00: scanning bus
[ 0.328675] pci 0000:00:00.0: [17cb:0101] type 01 class 0xff0000
[ 0.328851] pci 0000:00:00.0: supports D1
[ 0.328867] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 0.328889] pci 0000:00:00.0: PME# disabled
[ 0.332814] pci_bus 0000:00: fixups for bus
[ 0.332837] PCI: bus0: Fast back to back transfers disabled
[ 0.332859] pci 0000:00:00.0: scanning [bus 01-ff] behind bridge, pass 0
[ 0.333113] pci_bus 0000:01: scanning bus
[ 0.333303] pci 0000:01:00.0: [168c:0040] type 00 class 0x028000
[ 0.333686] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[ 0.334927] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[ 0.334976] pci 0000:01:00.0: PME# disabled
[ 0.335234] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5 GT/s x1 link)
[ 0.339202] pci_bus 0000:01: fixups for bus
[ 0.339279] PCI: bus1: Fast back to back transfers disabled
[ 0.339296] pci_bus 0000:01: bus scan returning with max=01
[ 0.339315] pci 0000:00:00.0: scanning [bus 01-ff] behind bridge, pass 1
[ 0.339333] pci_bus 0000:00: bus scan returning with max=ff
[ 0.339367] pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x081fffff]
[ 0.339392] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x081fffff 64bit]
[ 0.339529] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 0.339553] pci 0000:00:00.0: bridge window [mem 0x08000000-0x081fffff]
[ 0.339748] pcieport 0000:00:00.0: assign IRQ: got 35
[ 0.340507] pcieport 0000:00:00.0: AER: enabled with IRQ 36
[ 0.341094] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda not found, using dummy regulator
[ 0.341224] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda_phy not found, using dummy regulator
[ 0.341359] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda_refclk not found, using dummy regulator
[ 0.341632] qcom-pcie 1b700000.pci: host bridge /soc/pci@1b700000 ranges:
[ 0.341655] qcom-pcie 1b700000.pci: Parsing ranges property...
[ 0.341700] qcom-pcie 1b700000.pci: IO 0x31e00000..0x31efffff -> 0x31e00000
[ 0.341737] qcom-pcie 1b700000.pci: MEM 0x2e000000..0x31dfffff -> 0x2e000000
[ 0.570206] qcom-pcie 1b700000.pci: Link up
[ 0.570361] qcom-pcie 1b700000.pci: PCI host bridge to bus 0001:00
[ 0.570384] pci_bus 0001:00: root bus resource [bus 00-ff]
[ 0.570400] pci_bus 0001:00: root bus resource [mem 0x2e000000-0x31dfffff]
[ 0.570417] pci_bus 0001:00: scanning bus
[ 0.570459] pci 0001:00:00.0: [17cb:0101] type 01 class 0xff0000
[ 0.570615] pci 0001:00:00.0: supports D1
[ 0.570631] pci 0001:00:00.0: PME# supported from D0 D1 D3hot
[ 0.570651] pci 0001:00:00.0: PME# disabled
[ 0.574659] pci_bus 0001:00: fixups for bus
[ 0.574683] PCI: bus0: Fast back to back transfers disabled
[ 0.574704] pci 0001:00:00.0: scanning [bus 01-ff] behind bridge, pass 0
[ 0.574828] pci_bus 0001:01: scanning bus
[ 0.575006] pci 0001:01:00.0: [168c:0040] type 00 class 0x028000
[ 0.575359] pci 0001:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[ 0.576504] pci 0001:01:00.0: PME# supported from D0 D3hot D3cold
[ 0.576549] pci 0001:01:00.0: PME# disabled
[ 0.580713] pci_bus 0001:01: fixups for bus
[ 0.580783] PCI: bus1: Fast back to back transfers disabled
[ 0.580800] pci_bus 0001:01: bus scan returning with max=01
[ 0.580821] pci 0001:00:00.0: scanning [bus 01-ff] behind bridge, pass 1
[ 0.580837] pci_bus 0001:00: bus scan returning with max=ff
[ 0.580864] pci 0001:00:00.0: BAR 8: assigned [mem 0x2e000000-0x2e1fffff]
[ 0.580887] pci 0001:01:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit]
[ 0.581010] pci 0001:00:00.0: PCI bridge to [bus 01-ff]
[ 0.581030] pci 0001:00:00.0: bridge window [mem 0x2e000000-0x2e1fffff]
[ 0.581208] pcieport 0001:00:00.0: assign IRQ: got 37
[ 0.581920] pcieport 0001:00:00.0: AER: enabled with IRQ 38
[ 0.582514] qcom-pcie 1b900000.pci: 1b900000.pci supply vdda not found, using dummy regulator
[ 0.582639] qcom-pcie 1b900000.pci: 1b900000.pci supply vdda_phy not found, using dummy regulator
[ 0.582743] qcom-pcie 1b900000.pci: 1b900000.pci supply vdda_refclk not found, using dummy regulator
[ 0.583137] qcom-pcie 1b900000.pci: host bridge /soc/pci@1b900000 ranges:
[ 0.583159] qcom-pcie 1b900000.pci: Parsing ranges property...
[ 0.583204] qcom-pcie 1b900000.pci: IO 0x35e00000..0x35efffff -> 0x35e00000
[ 0.583239] qcom-pcie 1b900000.pci: MEM 0x32000000..0x35dfffff -> 0x32000000
[ 1.734047] qcom-pcie 1b900000.pci: Phy link never came up
[ 1.736110] qcom-pcie 1b900000.pci: cannot initialize host
[ 1.736480] qcom-pcie: probe of 1b900000.pci failed with error -110
[ 1.738819] L2 @ QSB rate. Forcing new rate.
[ 1.739044] L2 @ 384000 KHz
[ 1.739229] CPU0 @ 800000 KHz
[ 1.739242] CPU1 @ QSB rate. Forcing new rate.
[ 1.739371] CPU1 @ 384000 KHz
[ 1.743189] gsbi 16300000.gsbi: GSBI port protocol: 6 crci: 0
[ 1.745394] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 1.747836] msm_serial 16340000.serial: msm_serial: detected port #0
[ 1.747892] msm_serial 16340000.serial: uartclk = 7372800
[ 1.747964] 16340000.serial: ttyMSM0 at MMIO 0x16340000 (irq = 39, base_baud = 460800) is a MSM
[ 1.748004] msm_serial: console setup on port #0
[ 2.607912] printk: console [ttyMSM0] enabled
[ 2.612969] msm_serial: driver initialized
[ 2.622124] loop: module loaded
[ 2.623806] nand: device found, Manufacturer ID: 0x01, Chip ID: 0xa1
[ 2.624081] nand: AMD/Spansion S34MS01G2
[ 2.630676] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 2.634851] 19 fixed-partitions partitions found on MTD device qcom_nand.0
[ 2.641961] Creating 19 MTD partitions on "qcom_nand.0":
[ 2.648937] 0x000000000000-0x000000040000 : "SBL1"
[ 2.655828] 0x000000040000-0x000000180000 : "MIBIB"
[ 2.661900] 0x000000180000-0x0000002c0000 : "SBL2"
[ 2.666723] 0x0000002c0000-0x000000540000 : "SBL3"
[ 2.669241] random: fast init done
[ 2.677617] 0x000000540000-0x000000660000 : "DDRCONFIG"
[ 2.680433] 0x000000660000-0x000000780000 : "SSD"
[ 2.684661] 0x000000780000-0x000000a00000 : "TZ"
[ 2.691658] 0x000000a00000-0x000000c80000 : "RPM"
[ 2.696787] 0x000000c80000-0x000000dc0000 : "art"
[ 2.699806] 0x000000dc0000-0x000000ec0000 : "APPSBL"
[ 2.703288] 0x000000ec0000-0x000000f00000 : "u_env"
[ 2.707025] 0x000000f00000-0x000000f40000 : "s_env"
[ 2.711621] 0x000000f40000-0x000000f80000 : "devinfo"
[ 2.716561] 0x000000f80000-0x000003780000 : "kernel1"
[ 2.787076] 0x000001280000-0x000003780000 : "rootfs1"
[ 2.848746] 0x000003780000-0x000005f80000 : "kernel2"
[ 2.916053] 0x000003a80000-0x000005f80000 : "rootfs2"
[ 2.977859] 0x000005f80000-0x000006080000 : "sysdiag"
[ 2.980489] 0x000006080000-0x000008000000 : "syscfg"
[ 3.006600] random: crng init done
[ 3.036388] libphy: ipq8064_mdio_bus: probed
[ 3.057018] switch0: Atheros AR8337 rev. 2 switch registered on 37000000.mdio-mii
[ 3.885182] libphy: Fixed MDIO Bus: probed
[ 3.885843] ipq806x-gmac-dwmac 37200000.ethernet: IRQ eth_wake_irq not found
[ 3.888178] ipq806x-gmac-dwmac 37200000.ethernet: IRQ eth_lpi not found
[ 3.895723] ipq806x-gmac-dwmac 37200000.ethernet: PTP uses main clock
[ 3.902552] ipq806x-gmac-dwmac 37200000.ethernet: User ID: 0x10, Synopsys ID: 0x37
[ 3.908401] ipq806x-gmac-dwmac 37200000.ethernet: DWMAC1000
[ 3.915852] ipq806x-gmac-dwmac 37200000.ethernet: DMA HW capability register supported
[ 3.921600] ipq806x-gmac-dwmac 37200000.ethernet: RX Checksum Offload Engine supported
[ 3.929408] ipq806x-gmac-dwmac 37200000.ethernet: COE Type 2
[ 3.937311] ipq806x-gmac-dwmac 37200000.ethernet: TX Checksum insertion supported
[ 3.943121] ipq806x-gmac-dwmac 37200000.ethernet: Wake-Up On Lan supported
[ 3.950417] ipq806x-gmac-dwmac 37200000.ethernet: Enhanced/Alternate descriptors
[ 3.957273] ipq806x-gmac-dwmac 37200000.ethernet: Enabled extended descriptors
[ 3.964803] ipq806x-gmac-dwmac 37200000.ethernet: Ring mode enabled
[ 3.971768] ipq806x-gmac-dwmac 37200000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 3.978029] ipq806x-gmac-dwmac 37200000.ethernet: device MAC address 82:fe:c2:67:7f:3a
[ 3.987593] ipq806x-gmac-dwmac 37400000.ethernet: IRQ eth_wake_irq not found
[ 3.994434] ipq806x-gmac-dwmac 37400000.ethernet: IRQ eth_lpi not found
[ 4.001757] ipq806x-gmac-dwmac 37400000.ethernet: PTP uses main clock
[ 4.008476] ipq806x-gmac-dwmac 37400000.ethernet: User ID: 0x10, Synopsys ID: 0x37
[ 4.014576] ipq806x-gmac-dwmac 37400000.ethernet: DWMAC1000
[ 4.021942] ipq806x-gmac-dwmac 37400000.ethernet: DMA HW capability register supported
[ 4.027845] ipq806x-gmac-dwmac 37400000.ethernet: RX Checksum Offload Engine supported
[ 4.035561] ipq806x-gmac-dwmac 37400000.ethernet: COE Type 2
[ 4.043464] ipq806x-gmac-dwmac 37400000.ethernet: TX Checksum insertion supported
[ 4.049200] ipq806x-gmac-dwmac 37400000.ethernet: Wake-Up On Lan supported
[ 4.056648] ipq806x-gmac-dwmac 37400000.ethernet: Enhanced/Alternate descriptors
[ 4.063426] ipq806x-gmac-dwmac 37400000.ethernet: Enabled extended descriptors
[ 4.070900] ipq806x-gmac-dwmac 37400000.ethernet: Ring mode enabled
[ 4.078036] ipq806x-gmac-dwmac 37400000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 4.084178] ipq806x-gmac-dwmac 37400000.ethernet: device MAC address 9a:84:80:f8:0d:e3
[ 4.093863] i2c /dev entries driver
[ 4.102821] cpuidle: enable-method property 'qcom,kpss-acc-v1' found operations
[ 4.104166] cpuidle: enable-method property 'qcom,kpss-acc-v1' found operations
[ 4.111874] sdhci: Secure Digital Host Controller Interface driver
[ 4.118564] sdhci: Copyright(c) Pierre Ossman
[ 4.124780] sdhci-pltfm: SDHCI platform and OF driver helper
[ 4.131557] NET: Registered protocol family 10
[ 4.136639] Segment Routing with IPv6
[ 4.139211] NET: Registered protocol family 17
[ 4.142922] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 4.148412] 8021q: 802.1Q VLAN Support v1.8
[ 4.160473] Registering SWP/SWPB emulation handler
[ 4.186276] qcom_rpm 108000.rpm: RPM firmware 3.0.16777342
[ 4.201391] s1a: Bringing 0uV into 1050000-1050000uV
[ 4.201649] s1a: supplied by regulator-dummy
[ 4.205660] s1b: Bringing 0uV into 1050000-1050000uV
[ 4.209864] s1b: supplied by regulator-dummy
[ 4.214814] s2a: Bringing 0uV into 800000-800000uV
[ 4.219072] s2a: supplied by regulator-dummy
[ 4.223702] s2b: Bringing 0uV into 800000-800000uV
[ 4.228118] s2b: supplied by regulator-dummy
[ 4.241205] ubi0: attaching mtd14
[ 4.512333] ubi0: scanning is finished
[ 4.522595] ubi0: attached mtd14 (name "rootfs1", size 37 MiB)
[ 4.522615] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 4.527366] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 4.534237] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 4.541025] ubi0: good PEBs: 296, bad PEBs: 0, corrupted PEBs: 0
[ 4.547865] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[ 4.554106] ubi0: max/mean erase counter: 6/4, WL threshold: 4096, image sequence number: 721178430
[ 4.561084] ubi0: available PEBs: 0, total reserved PEBs: 296, PEBs reserved for bad PEB handling: 20
[ 4.570843] block ubiblock0_0: created from ubi0:0(rootfs)
[ 4.571068] ubi0: background thread "ubi_bgt0d" started, PID 67
[ 4.579470] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[ 4.579476] hctosys: unable to open rtc device (rtc0)
[ 4.606264] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 4.608731] Freeing unused kernel memory: 1024K
[ 4.634268] Run /sbin/init as init process
[ 5.215108] init: Console is alive
[ 5.215248] init: - watchdog -
[ 5.721337] kmodloader: loading kernel modules from /etc/modules-boot.d/

[ 5.842780] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.851130] SCSI subsystem initialized
[ 5.857842] libata version 3.00 loaded.
[ 5.862610] ehci-fsl: Freescale EHCI Host controller driver
[ 5.863515] ehci-platform: EHCI generic platform driver
[ 5.871565] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 5.872644] ohci-platform: OHCI generic platform driver
[ 5.880897] dwc3-qcom 110f8800.usb3: IRQ hs_phy_irq not found
[ 5.883630] dwc3-qcom 110f8800.usb3: IRQ dp_hs_phy_irq not found
[ 5.889467] dwc3-qcom 110f8800.usb3: IRQ dm_hs_phy_irq not found
[ 5.895626] dwc3-qcom 110f8800.usb3: IRQ ss_phy_irq not found
[ 5.903022] dwc3-qcom 100f8800.usb3: IRQ hs_phy_irq not found
[ 5.907178] dwc3-qcom 100f8800.usb3: IRQ dp_hs_phy_irq not found
[ 5.912905] dwc3-qcom 100f8800.usb3: IRQ dm_hs_phy_irq not found
[ 5.919070] dwc3-qcom 100f8800.usb3: IRQ ss_phy_irq not found
[ 5.926523] dwc3 11000000.dwc3: Failed to get clk 'ref': -2
[ 6.023609] dwc3 10000000.dwc3: Failed to get clk 'ref': -2
[ 6.125576] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 6.125638] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 6.130173] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000000002010010
[ 6.137695] xhci-hcd xhci-hcd.0.auto: irq 42, io mem 0x11000000
[ 6.147987] hub 1-0:1.0: USB hub found
[ 6.152848] hub 1-0:1.0: 1 port detected
[ 6.156911] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 6.160689] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 6.166047] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
[ 6.174178] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 6.180500] hub 2-0:1.0: USB hub found
[ 6.188464] hub 2-0:1.0: 1 port detected
[ 6.192210] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 6.196099] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
[ 6.201456] xhci-hcd xhci-hcd.1.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000000002010010
[ 6.208948] xhci-hcd xhci-hcd.1.auto: irq 43, io mem 0x10000000
[ 6.218852] hub 3-0:1.0: USB hub found
[ 6.224247] hub 3-0:1.0: 1 port detected
[ 6.228166] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 6.232042] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
[ 6.237424] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
[ 6.245611] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[ 6.251849] hub 4-0:1.0: USB hub found
[ 6.259808] hub 4-0:1.0: 1 port detected
[ 6.264523] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 6.272723] init: - preinit -
[ 8.262031] dwmac1000: Master AXI performs any burst length
[ 8.262091] ipq806x-gmac-dwmac 37400000.ethernet eth1: No Safety Features support found
[ 8.266585] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[ 8.274719] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
[ 8.283526] ipq806x-gmac-dwmac 37400000.ethernet eth1: configuring for fixed/sgmii link mode
[ 8.291891] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[ 8.301517] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 12.508873] UBIFS (ubi0:1): Mounting in unauthenticated mode
[ 12.509029] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 164
[ 12.574103] UBIFS (ubi0:1): recovery needed
[ 12.696355] UBIFS (ubi0:1): recovery completed
[ 12.696439] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[ 12.699733] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 12.707680] UBIFS (ubi0:1): FS size: 29966336 bytes (28 MiB, 236 LEBs), journal size 1523712 bytes (1 MiB, 12 LEBs)
[ 12.717575] UBIFS (ubi0:1): reserved for root: 1415383 bytes (1382 KiB)
[ 12.727790] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID 2D26C0E5-ACFF-42FC-A289-667C2C11BE5C, small LPT model
[ 12.743419] mount_root: switching to ubifs overlay
[ 12.757198] urandom-seed: Seeding with /etc/urandom.seed
[ 12.824389] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Down
[ 12.879662] procd: - early -
[ 12.879756] procd: - watchdog -
[ 13.476531] procd: - watchdog -
[ 13.477132] procd: - ubus -
[ 13.539555] procd: - init -
[ 14.178894] urngd: v1.0.2 started.
[ 14.293565] kmodloader: loading kernel modules from /etc/modules.d/*
[ 14.304486] Mirror/redirect action on
[ 14.322227] u32 classifier
[ 14.322244] input device check on
[ 14.323891] Actions configured
[ 14.354661] Loading modules backported from Linux version v5.8-0-gbcf876870b95
[ 14.354684] Backport generated by backports.git v5.8-1-0-g79400d9e
[ 14.389584] xt_time: kernel timezone is -0000
[ 14.448919] PPP generic driver version 2.4.2
[ 14.449550] NET: Registered protocol family 24
[ 14.473273] ath10k_pci 0000:01:00.0: assign IRQ: got 35
[ 14.473297] ath10k 5.4 driver, optimized for CT firmware, probing pci device: 0x40.
[ 14.473353] ath10k_mac_create, priv_size: 868 hw: fcb698fa hw->priv: 49071807
[ 14.480192] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142)
[ 14.487188] ath10k_pci 0000:01:00.0: enabling bus mastering
[ 14.487765] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[ 15.231735] ath10k_pci 0000:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003b01ff sub 168c:0002
[ 15.231768] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[ 15.241672] ath10k_pci 0000:01:00.0: firmware ver 10.4b-ct-9980-fW-13-10af6a005 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 4a0fa880
[ 15.313277] ath10k_pci 0000:01:00.0: board_file api 2 bmi_id 1:2 crc32 08fa09f2
[ 16.502830] ath10k_pci 0000:01:00.0: unsupported HTC service id: 1536
[ 16.505622] ath10k_pci 0000:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
[ 16.508253] ath10k_pci 0000:01:00.0: msdu-desc: 2500 skid: 32
[ 16.588293] ath10k_pci 0000:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
[ 16.588328] ath10k_pci 0000:01:00.0: wmi print 'free: 31080 iram: 23092 sram: 9596'
[ 16.883204] ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1
[ 16.975449] ath: EEPROM regdomain sanitized
[ 16.975466] ath: EEPROM regdomain: 0x64
[ 16.975478] ath: EEPROM indicates we should expect a direct regpair map
[ 16.975502] ath: Country alpha2 being used: 00
[ 16.975511] ath: Regpair used: 0x64
[ 16.980598] ath10k_pci 0001:01:00.0: assign IRQ: got 37
[ 16.980638] ath10k 5.4 driver, optimized for CT firmware, probing pci device: 0x40.
[ 16.980772] ath10k_mac_create, priv_size: 868 hw: 4da8e3e7 hw->priv: dea94892
[ 16.988147] ath10k_pci 0001:01:00.0: enabling device (0140 -> 0142)
[ 16.994540] ath10k_pci 0001:01:00.0: enabling bus mastering
[ 16.995092] ath10k_pci 0001:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[ 17.754957] ath10k_pci 0001:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003b01ff sub 168c:0002
[ 17.754989] ath10k_pci 0001:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[ 17.765020] ath10k_pci 0001:01:00.0: firmware ver 10.4b-ct-9980-fW-13-10af6a005 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 4a0fa880
[ 17.837495] ath10k_pci 0001:01:00.0: board_file api 2 bmi_id 1:1 crc32 08fa09f2
[ 19.023638] ath10k_pci 0001:01:00.0: unsupported HTC service id: 1536
[ 19.026608] ath10k_pci 0001:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
[ 19.029078] ath10k_pci 0001:01:00.0: msdu-desc: 2500 skid: 32
[ 19.107393] ath10k_pci 0001:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
[ 19.107453] ath10k_pci 0001:01:00.0: wmi print 'free: 31080 iram: 23092 sram: 9596'
[ 19.381061] ath10k_pci 0001:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1
[ 19.475552] ath: EEPROM regdomain sanitized
[ 19.475567] ath: EEPROM regdomain: 0x64
[ 19.475578] ath: EEPROM indicates we should expect a direct regpair map
[ 19.475606] ath: Country alpha2 being used: 00
[ 19.475616] ath: Regpair used: 0x64
[ 19.494500] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 24.022806] dwmac1000: Master AXI performs any burst length
[ 24.022837] ipq806x-gmac-dwmac 37400000.ethernet eth1: No Safety Features support found
[ 24.027289] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[ 24.035383] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
[ 24.044311] ipq806x-gmac-dwmac 37400000.ethernet eth1: configuring for fixed/sgmii link mode
[ 24.051205] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[ 24.065371] br-lan: port 1(eth1.1) entered blocking state
[ 24.068503] br-lan: port 1(eth1.1) entered disabled state
[ 24.074169] device eth1.1 entered promiscuous mode
[ 24.079259] device eth1 entered promiscuous mode
[ 24.086112] br-lan: port 1(eth1.1) entered blocking state
[ 24.088725] br-lan: port 1(eth1.1) entered forwarding state
[ 24.103056] dwmac1000: Master AXI performs any burst length
[ 24.103090] ipq806x-gmac-dwmac 37200000.ethernet eth0: No Safety Features support found
[ 24.107437] ipq806x-gmac-dwmac 37200000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[ 24.118117] ipq806x-gmac-dwmac 37200000.ethernet eth0: registered PTP clock
[ 24.124607] ipq806x-gmac-dwmac 37200000.ethernet eth0: configuring for fixed/rgmii link mode
[ 24.132087] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[ 24.141675] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 24.921934] ath: EEPROM regdomain: 0x826c
[ 24.921940] ath: EEPROM indicates we should expect a country code
[ 24.921945] ath: doing EEPROM country->regdmn map search
[ 24.921950] ath: country maps to regdmn code: 0x37
[ 24.921955] ath: Country alpha2 being used: PT
[ 24.921958] ath: Regpair used: 0x37
[ 24.921962] ath: regdomain 0x826c dynamically updated by user
[ 24.921976] ath: EEPROM regdomain: 0x826c
[ 24.921979] ath: EEPROM indicates we should expect a country code
[ 24.921983] ath: doing EEPROM country->regdmn map search
[ 24.921986] ath: country maps to regdmn code: 0x37
[ 24.921990] ath: Country alpha2 being used: PT
[ 24.921993] ath: Regpair used: 0x37
[ 24.921996] ath: regdomain 0x826c dynamically updated by user
[ 25.033179] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 25.033449] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 27.721766] ath10k_pci 0001:01:00.0: unsupported HTC service id: 1536
[ 27.722195] ath10k_pci 0001:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
[ 27.727294] ath10k_pci 0001:01:00.0: msdu-desc: 2500 skid: 32
[ 27.805670] ath10k_pci 0001:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
[ 27.805757] ath10k_pci 0001:01:00.0: wmi print 'free: 31080 iram: 23092 sram: 9596'
[ 28.182204] ath10k_pci 0001:01:00.0: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4
[ 28.193288] br-lan: port 2(wlan1) entered blocking state
[ 28.193336] br-lan: port 2(wlan1) entered disabled state
[ 28.198315] device wlan1 entered promiscuous mode
[ 28.219104] ath10k_pci 0001:01:00.0: NOTE: Firmware DBGLOG output disabled in debug_mask: 0x10000000
[ 29.497513] ath10k_pci 0000:01:00.0: unsupported HTC service id: 1536
[ 29.499844] ath10k_pci 0000:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
[ 29.502932] ath10k_pci 0000:01:00.0: msdu-desc: 2500 skid: 32
[ 29.582991] ath10k_pci 0000:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
[ 29.583148] ath10k_pci 0000:01:00.0: wmi print 'free: 31080 iram: 23092 sram: 9596'
[ 29.994095] ath10k_pci 0000:01:00.0: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4
[ 30.003183] br-lan: port 3(wlan0) entered blocking state
[ 30.004042] br-lan: port 3(wlan0) entered disabled state
[ 30.009837] device wlan0 entered promiscuous mode
[ 30.447505] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 30.447859] br-lan: port 3(wlan0) entered blocking state
[ 30.453002] br-lan: port 3(wlan0) entered forwarding state
[ 30.547211] ath10k_pci 0000:01:00.0: wmi: fixing invalid VHT TX rate code 0xff
[ 30.819917] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 30.820300] br-lan: port 2(wlan1) entered blocking state
[ 30.825492] br-lan: port 2(wlan1) entered forwarding state
[91724.922526] ath10k_pci 0000:01:00.0: Setting debug-mask to: 0xc0000032 old: 0x10000000
[91725.487789] ath10k_pci 0001:01:00.0: ath10k_pci ATH10K_DBG_BUFFER:
[91725.487904] ath10k: [0000]: 0598AA1D 10005881 00003112 00425D28 0000000A 00000000 0598AA1D 10005881
[91725.492899] ath10k: [0008]: 00003112 00425D28 0000000E 00000001
[91725.501856] ath10k_pci 0001:01:00.0: ATH10K_END
[91725.939329] ath10k_pci 0000:01:00.0: ath10k_pci ATH10K_DBG_BUFFER:
[91725.939391] ath10k: [0000]: 05990746 10005881 00003112 00425D28 0000000A 00000000 05990748 10005881
[91725.944425] ath10k: [0008]: 00003112 00425D28 0000000E 00000001
[91725.953438] ath10k_pci 0000:01:00.0: ATH10K_END
[91731.488618] ath10k_pci 0001:01:00.0: ath10k_pci ATH10K_DBG_BUFFER:
[91731.488735] ath10k: [0000]: 0598C221 10005881 00003112 00425D28 0000000A 00000000 0598C221 10005881
[91731.493730] ath10k: [0008]: 00003112 00425D28 0000000E 00000001
[91731.502683] ath10k_pci 0001:01:00.0: ATH10K_END
[91731.939521] ath10k_pci 0000:01:00.0: ath10k_pci ATH10K_DBG_BUFFER:
[91731.939578] ath10k: [0000]: 05991F4D 10005881 00003112 00425D28 0000000A 00000000 05991F4D 10005881
[91731.944641] ath10k: [0008]: 00003112 00425D28 0000000E 00000001
[91731.953708] ath10k_pci 0000:01:00.0: ATH10K_END
[91737.488542] ath10k_pci 0001:01:00.0: ath10k_pci ATH10K_DBG_BUFFER:
[91737.488605] ath10k: [0000]: 0598DA27 10005881 00003112 00425D28 0000000A 00000000 0598DA27 10005881
[91737.493672] ath10k: [0008]: 00003112 00425D28 0000000E 00000001 0598DAFA 17FC5823 00000033 004479C8
[91737.502713] ath10k: [0016]: C6C70104 0000005D 00000040
[91737.511709] ath10k_pci 0001:01:00.0: ATH10K_END
[91737.938736] ath10k_pci 0000:01:00.0: ath10k_pci ATH10K_DBG_BUFFER:
[91737.938851] ath10k: [0000]: 05993753 10005881 00003112 00425D28 0000000A 00000000 05993755 10005881
[91737.943843] ath10k: [0008]: 00003112 00425D28 0000000E 00000001
[91737.952798] ath10k_pci 0000:01:00.0: ATH10K_END
[91743.490952] ath10k_pci 0001:01:00.0: ath10k_pci ATH10K_DBG_BUFFER:
[91743.491075] ath10k: [0000]: 0598F22D 10005881 00003112 00425D28 0000000A 00000000 0598F22D 10005881
[91743.496065] ath10k: [0008]: 00003112 00425D28 0000000E 00000001
[91743.504997] ath10k_pci 0001:01:00.0: ATH10K_END
[91743.937037] ath10k_pci 0000:01:00.0: ath10k_pci ATH10K_DBG_BUFFER:
[91743.937129] ath10k: [0000]: 05994F5B 10005881 00003112 00425D28 0000000A 00000000 05994F5D 10005881
[91743.942145] ath10k: [0008]: 00003112 00425D28 0000000E 00000001
[91743.951101] ath10k_pci 0000:01:00.0: ATH10K_END
[91747.491780] ath10k_pci 0001:01:00.0: ath10k_pci ATH10K_DBG_BUFFER:
[91747.491895] ath10k: [0000]: 0598FF80 17FC5823 00000033 004479C8 C6C70004 00000000 00000002 0599011E
[91747.496894] ath10k: [0008]: 1400581D 00000000 004479C8 000F6690 00000006 00000000 0599011E 1000581B
[91747.505869] ath10k: [0016]: 0000C6C7 00000000 00000000 000F6690 05990120 14006402 71103332 03ADDE38
[91747.514878] ath10k: [0024]: 0000C7C6 00423A04 00000001 05990120 1000587B 00425D28 004479C8 00000000
[91747.523887] ath10k: [0032]: 00423A04 05990120 1400587D 51100002 000F6690 00000001 00000004 004479C8
[91747.532932] ath10k: [0040]: 05990121 10005881 00003112 00425D28 0000000A 00000000 05990121 10005881
[91747.541943] ath10k: [0048]: 00003112 00425D28 0000000E 00000001
[91747.550966] ath10k_pci 0001:01:00.0: ATH10K_END
[91749.492076] ath10k_pci 0001:01:00.0: ath10k_pci ATH10K_DBG_BUFFER:
[91749.492173] ath10k: [0000]: 05990A2F 10005881 00003112 00425D28 0000000A 00000000 05990A2F 10005881
[91749.497209] ath10k: [0008]: 00003112 00425D28 0000000E 00000001
[91749.506120] ath10k_pci 0001:01:00.0: ATH10K_END
[91749.937455] ath10k_pci 0000:01:00.0: ath10k_pci ATH10K_DBG_BUFFER:
[91749.937572] ath10k: [0000]: 05996760 10005881 00003112 00425D28 0000000A 00000000 05996760 10005881
[91749.942582] ath10k: [0008]: 00003112 00425D28 0000000E 00000001
[91749.951499] ath10k_pci 0000:01:00.0: ATH10K_END
[91754.491907] ath10k_pci 0001:01:00.0: ath10k_pci ATH10K_DBG_BUFFER:
[91754.491971] ath10k: [0000]: 05991D0D 1400587C 51100001 000F6690 000003FC 00000005 004479C8 05991D0D
[91754.497019] ath10k: [0008]: 1000587A 00425D28 004479C8 01000000 00000001 05991D0D 14006403 03ADDE38
[91754.505942] ath10k: [0016]: C7C60000 00000001 00000000 004479C8 05991D10 10005881 00003112 00425D28
[91754.514965] ath10k: [0024]: 0000000A 00000000 05991D10 10005881 00003112 00425D28 0000000E 00000001
[91754.524006] ath10k: [0032]: 05991D11 10004C01 71100D08 00000000 0000000A 00000077 05991D11 14004C01
[91754.533021] ath10k: [0040]: 71104441 030AC6C7 0601B003 0000FFFA 0000FFFF 05991D11 13FC4C01 000081DF
[91754.542048] ath10k: [0048]: 0044F8BD 00000008 0000004D 05991D11 14004C01 71108880 00000000 00C4004D
[91754.551077] ath10k: [0056]: 00000000 00000FF0 05991D11 14004C01 71108880 00010000 00C4004D 00000000
[91754.560105] ath10k: [0064]: 0000FFFF 05991D11 14004C01 71108880 00020000 00C4004D 00000000 0000FFFF
[91754.569133] ath10k: [0072]: 05991D11 14004C01 71108880 00030000 00C4004D 00000000 0007FDF7 05991D11
[91754.578182] ath10k: [0080]: 14004C01 71108880 00040000 00C4004D 00000000 000FFFFF 05991D11 14004C01
[91754.587205] ath10k: [0088]: 71108880 00050000 00C4004D 00000000 00000000 05991D12 14004C01 71104441
[91754.596222] ath10k: [0096]: 030AC6C7 0601B003 0000FFFA 0000FFFF 05991D12 13FC4C01 000081DF 00450F41
[91754.605251] ath10k: [0104]: 00000008 0000004D 05991D12 14004C01 71108880 00000000 00C4004D 00000000
[91754.614277] ath10k: [0112]: 00000FF0 05991D12 14004C01 71108880 00010000 00C4004D 00000000 0000FFFF
[91754.623304] ath10k: [0120]: 05991D12 14004C01 71108880 00020000 00C4004D 00000000 0000FFFF 05991D12
[91754.632331] ath10k: [0128]: 14004C01 71108880 00030000 00C4004D 00000000 0007FDF7 05991D12 14004C01
[91754.641361] ath10k: [0136]: 71108880 00040000 00C4004D 00000000 000FFFFF 05991D12 14004C01 71108880
[91754.650388] ath10k: [0144]: 00050000 00C4004D 00000000 00000000 05991D19 1400581D 000F6690 004479C8
[91754.659425] ath10k: [0152]: 000F6690 00000006 00004000 05991D19 1000581B 0000C6C7 00000000 00000006
[91754.668442] ath10k: [0160]: 000F6690 05991D46 17FC5402 00000048 00000001 00000000 0000FFFE 00000000
[91754.677470] ath10k: [0168]: 05991D46 17FC5402 00000049 00000000 00000000 00000000 00000000 05991D46
[91754.686499] ath10k: [0176]: 0FFC5402 00003ADD 00000001 00000000 05991D69 17FC5823 00000033 004479C8
[91754.695525] ath10k: [0184]: C6C70100 00000000 00000040 05991D71 17FC5823 00000033 004479C8 C6C70106
[91754.704553] ath10k: [0192]: 00000002 00000040 05991DA1 17FC5823 00000033 004479C8 C6C70104 00000000
[91754.713581] ath10k: [0200]: 00000040
[91754.722602] ath10k_pci 0001:01:00.0: ATH10K_END
[91755.493237] ath10k_pci 0001:01:00.0: ath10k_pci ATH10K_DBG_BUFFER:
[91755.493325] ath10k: [0000]: 05992230 10005881 00003112 00425D28 0000000A 00000000 05992230 10005881
[91755.498359] ath10k: [0008]: 00003112 00425D28 0000000E 00000001
[91755.507317] ath10k_pci 0001:01:00.0: ATH10K_END
[91755.937204] ath10k_pci 0000:01:00.0: ath10k_pci ATH10K_DBG_BUFFER:
[91755.937290] ath10k: [0000]: 05997F63 10005881 00003112 00425D28 0000000A 00000000 05997F63 10005881
[91755.942347] ath10k: [0008]: 00003112 00425D28 0000000E 00000001
[91755.951257] ath10k_pci 0000:01:00.0: ATH10K_END
[91759.494184] ath10k_pci 0001:01:00.0: ath10k_pci ATH10K_DBG_BUFFER:
[91759.494244] ath10k: [0000]: 05993173 17FC5823 00000033 004479C8 C6C70006 00000000 00000002
[91759.499432] ath10k_pci 0001:01:00.0: ATH10K_END
[91761.494681] ath10k_pci 0001:01:00.0: ath10k_pci ATH10K_DBG_BUFFER:
[91761.494758] ath10k: [0000]: 05993A34 10005881 00003112 00425D28 0000000A 00000000 05993A34 10005881
[91761.499772] ath10k: [0008]: 00003112 00425D28 0000000E 00000001
[91761.508727] ath10k_pci 0001:01:00.0: ATH10K_END
[91761.936631] ath10k_pci 0000:01:00.0: ath10k_pci ATH10K_DBG_BUFFER:
[91761.936732] ath10k: [0000]: 05999769 10005881 00003112 00425D28 0000000A 00000000 05999769 10005881
[91761.941746] ath10k: [0008]: 00003112 00425D28 0000000E 00000001
[91761.950680] ath10k_pci 0000:01:00.0: ATH10K_END
[91764.495201] ath10k_pci 0001:01:00.0: ath10k_pci ATH10K_DBG_BUFFER:
[91764.495296] ath10k: [0000]: 05994580 17FC5823 00000033 004479C8 C6C70004 00000000 00000002
[91764.500312] ath10k_pci 0001:01:00.0: ATH10K_END

@openwrt-bot
Copy link
Author

tiagofreire-pt:

The above dmesg log was made using the CT driver on OpenWrt SNAPSHOT, r14954-aafbfc6ac3.

@openwrt-bot
Copy link
Author

adrian-bl:

Can confirm: Having the same issue on 21.02.0-rc1, switching to the non-CT driver seems to fix the TX issue.

@aparcar aparcar added the kernel pull request/issue with Linux kernel related changes label Feb 22, 2022
@bobaoapae
Copy link

Hello any news on this? I can get around 600MBps on this device with original firmware, and with openwrt only 200~300

@GMichu
Copy link

GMichu commented Nov 17, 2022

Same problem on QCA9992
OpenWrt 22.03.2 r19803-9a599fee93

@bkdwt
Copy link

bkdwt commented Mar 11, 2023

@luisimasd
Copy link

luisimasd commented Aug 21, 2023

I observed we have ...

ath10k-firmware-qca99x0 | 20230804-1 | 363.19 KiB | ath10k qca99x0 firmware

ath10k-firmware-qca99x0-ct | 2020-11-08-1 | 423.59 KiB | Alternative ath10k firmware for QCA99x0 from Candela Technologies.… | Installed

ath10k-firmware-qca99x0-ct-full-htt | 2020-11-08-1 | 423.50 KiB | Alternative ath10k firmware for QCA99x0 from Candela Technologies.… |
ath10k-firmware-qca99x0-ct-htt | 2020-11-08-1 | 385.43 KiB | Alternative ath10k firmware for QCA99x0 from Candela Technologies.… |

Some questions from my side:

  • Any place to find information about the difference between the packages listed above for this QCA99x0 chip?
  • With the ath10k-firmware-qca99x0-ct the 5G Wifi seems to be up in the openwrt but not TX, changed to 40Mhz didn't make the difference. Any idea?

Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment
Labels
flyspray kernel pull request/issue with Linux kernel related changes
Projects
None yet
Development

No branches or pull requests

6 participants