You signed in with another tab or window. Reload to refresh your session.You signed out in another tab or window. Reload to refresh your session.You switched accounts on another tab or window. Reload to refresh your session.Dismiss alert
Software versions of OpenWrt/LEDE release, packages, etc. - 19.07.3
I think it's a bug/overlooked use case, but when you have interfaces bridged in the UCI config, the MTU setting does not get applied to the member interfaces (physical or VLAN).
config interface 'lan'
option proto 'static'
option netmask '255.255.255.0'
option ip6assign '60'
option ipaddr '192.168.1.1'
option type 'bridge'
option mtu '9000'
option ifname 'eth1 eth4.10'
When I boot using this config I have connectivity issues with devices using Jumbo frames. ifconfig confirms that MTUs on the members interfaces are still at default 1500.
eth1 Link encap:Ethernet HWaddr 0C:C4:7A:AB:39:3D
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Memory:df440000-df45ffff
supersebbo:
I think it's a bug/overlooked use case, but when you have interfaces bridged in the UCI config, the MTU setting does not get applied to the member interfaces (physical or VLAN).
config interface 'lan'
option proto 'static'
option netmask '255.255.255.0'
option ip6assign '60'
option ipaddr '192.168.1.1'
option type 'bridge'
option mtu '9000'
option ifname 'eth1 eth4.10'
When I boot using this config I have connectivity issues with devices using Jumbo frames. ifconfig confirms that MTUs on the members interfaces are still at default 1500.
eth1 Link encap:Ethernet HWaddr 0C:C4:7A:AB:39:3D
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Memory:df440000-df45ffff
eth4 Link encap:Ethernet HWaddr 3C:FD:FE:BB:01:50
inet6 addr: fe80::3efd:feff:febb:150/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:50176 errors:0 dropped:1 overruns:0 frame:0
TX packets:37468 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:15692679 (14.9 MiB) TX bytes:29263711 (27.9 MiB)
eth4.10 Link encap:Ethernet HWaddr 3C:FD:FE:BB:01:50
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:36728 errors:0 dropped:0 overruns:0 frame:0
TX packets:20850 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:9314410 (8.8 MiB) TX bytes:26473088 (25.2 MiB)
I have to manually use the ifconfig tool to set the MTU (i.e. ifconfig eth4.10 mtu 9000) to get the network back up and running correctly.
Obviously these commands could be scritped, however it was my understanding the UCI network config should be doing this .
The text was updated successfully, but these errors were encountered: