OpenWrt/LEDE Project

  • Status Unconfirmed
  • Percent Complete
    0%
  • Task Type Bug Report
  • Category Base system
  • Assigned To No-one
  • Operating System All
  • Severity Low
  • Priority Very Low
  • Reported Version openwrt-19.07
  • Due in Version Undecided
  • Due Date Undecided
  • Private
Attached to Project: OpenWrt/LEDE Project
Opened by Troport - 21.06.2020

FS#3196 - OpenWRT on Freescale's P2020RDB

I’m trying to run OpenWRT on a P2020RDB board, I managed to fetch the release mpc85xx initramfs.bin from here (I failed to get the snapshot one for Freescale over here as I received a 403 error), and then I pulled it into uboot using tftpboot, and placed it at address “0×1000000“, and ran “bootm 0×1000000” the kernel starts and then I get a call trace and some stuff get dumped:

XTM-330_P2020(FAILSAFE) => bootm 0x1000000                                                                                                                      [165/195]
WARNING: adjusting available memory to 30000000                                                                                                                          
## Booting kernel from FIT Image at 01000000 ...                                                                                                                         
   Using 'config@1' configuration                                                                                                                                        
   Trying 'kernel@1' kernel subimage                                                                                                                                     
     Description:  POWERPC OpenWrt Linux-4.14.180                                                                                                                        
     Type:         Kernel Image                                                                                                                                          
     Compression:  gzip compressed                                                                                                                                       
     Data Start:   0x010000ec                                                                                                                                            
     Data Size:    5128735 Bytes = 4.9 MiB                                                                                                                               
     Architecture: PowerPC                                                                                                                                               
     OS:           Linux                                                                                                                                                 
     Load Address: 0x00000000
     Entry Point:  0x00000000
     Hash algo:    crc32
     Hash value:   7754597c
     Hash algo:    sha1
     Hash value:   bd433c824dc74e015b759f3ab53ffe996b130f2e
   Verifying Hash Integrity ... crc32+ sha1+ OK
## Flattened Device Tree from FIT Image at 01000000
   Using 'config@1' configuration
   Trying 'fdt@1' FDT blob subimage
     Description:  POWERPC OpenWrt p2020rdb device tree blob
     Type:         Flat Device Tree
     Compression:  uncompressed
     Data Start:   0x014e4448
     Data Size:    12550 Bytes = 12.3 KiB
     Architecture: PowerPC
     Hash algo:    crc32
     Hash value:   0d1ae91a
     Hash algo:    sha1
     Hash value:   fdbac0f412982769bdef3ba414fc6716b8a855d4
   Verifying Hash Integrity ... crc32+ sha1+ OK
   Booting using the fdt blob at 0x14e4448 
   Uncompressing Kernel Image ... OK
   Loading Device Tree to 00ff9000, end 00fff105 ... OK
[    0.000000] Memory CAM mapping: 256/256/256 Mb, residual: 256Mb
[    0.000000] Linux version 4.14.180 (builder@buildhost) (gcc version 7.5.0 (OpenWrt GCC 7.5.0 r11063-85e04e9f46)) #0 SMP Sat May 16 18:32:20 2020
[    0.000000] Using P2020 RDB machine description
[    0.000000] bootconsole [udbg0] enabled
[    0.000000] CPU maps initialized for 1 thread per core
[    0.000000] -----------------------------------------------------
[    0.000000] phys_mem_size     = 0x30000000
[    0.000000] dcache_bsize      = 0x20
[    0.000000] icache_bsize      = 0x20
[    0.000000] cpu_features      = 0x0000000012100460
[    0.000000]   possible        = 0x0000000012120460
[    0.000000]   always          = 0x0000000000100000
[    0.000000] cpu_user_features = 0x84e08000 0x08000000
[    0.000000] mmu_features      = 0x00020010
[    0.000000] -----------------------------------------------------
mpc85xx_rdb_setup_arch()
[    0.000000] mpc85xx_qe_init: Could not find Quicc Engine node
[    0.000000] MPC85xx RDB board from Freescale Semiconductor
[    0.000000] barrier-nospec: using isync; sync as speculation barrier
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000000000000-0x000000002fffffff]
[    0.000000]   Normal   empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x000000002fffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000002fffffff]
[    0.000000] MMU: Allocated 1088 bytes of context maps for 255 contexts
[    0.000000] percpu: Embedded 12 pages/cpu s18380 r8192 d22580 u49152
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 195072
[    0.000000] Kernel command line: root=/dev/sda1 rw rootdelay=30 console=ttyS0,115200 ramdisk_size=600000
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Memory: 705444K/786432K available (4400K kernel code, 176K rwdata, 548K rodata, 2620K init, 216K bss, 80988K reserved, 0K cma-reserved)
[    0.000000] Kernel virtual memory layout:
[    0.000000]   * 0xfffdf000..0xfffff000  : fixmap
[    0.000000]   * 0xfdffe000..0xfe000000  : early ioremap
[    0.000000]   * 0xf1000000..0xfdffe000  : vmalloc & ioremap
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS: 512, nr_irqs: 512, preallocated irqs: 16
[    0.000000] mpic: Setting up MPIC " OpenPIC  " version 1.2 at ffe40000, max 2 CPUs
[    0.000000] mpic: ISU size: 256, shift: 8, mask: ff
[    0.000000] mpic: Initializing for 256 sources
[    0.000000] mpc85xx_rdb_pic_init: Could not find qe-ic node
[    0.000010] clocksource: timebase: mask: 0xffffffffffffffff max_cycles: 0xf6018975a, max_idle_ns: 440795204712 ns
[    0.010162] clocksource: timebase mult[f000003] shift[24] registered
[    0.016543] pid_max: default: 32768 minimum: 301
[    0.021182] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.027710] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.035198] mpic: requesting IPIs...
[    0.039003] Hierarchical SRCU implementation.
[    0.043596] smp: Bringing up secondary CPUs ...
[    0.048509] smp: Brought up 1 node, 2 CPUs
[    0.052518] Using shared cache scheduler topology
[    0.058928] random: get_random_u32 called from 0xc0201c80 with crng_init=0
[    0.065843] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.075502] futex hash table entries: 512 (order: 2, 16384 bytes)
[    0.081889] NET: Registered protocol family 16
[    0.094212] Found FSL PCI host bridge at 0x00000000ffe0a000. Firmware bus number: 0->0
[    0.102052] PCI host bridge /pcie@ffe0a000 (primary) ranges:
[    0.107677]  MEM 0x0000000080000000..0x000000009fffffff -> 0x0000000080000000 
[    0.114869]   IO 0x00000000ffc00000..0x00000000ffc0ffff -> 0x0000000000000000
[    0.121993] /pcie@ffe0a000: PCICSRBAR @ 0xfff00000
[    0.126746] setup_pci_atmu: end of DRAM 30000000
[    0.131344] /pcie@ffe0a000: Setting PCI inbound window greater than memory size
[    0.146042] PCI: Probing PCI hardware
[    0.149766] fsl-pci ffe0a000.pcie: PCI host bridge to bus a000:00
[    0.155778] pci_bus a000:00: root bus resource [io  0x0000-0xffff]
[    0.161927] pci_bus a000:00: root bus resource [mem 0x80000000-0x9fffffff]
[    0.168774] pci_bus a000:00: root bus resource [bus 00-ff]
[    0.174535] pci a000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    0.182529] pci a000:00:00.0: PCI bridge to [bus 01-ff]
[    0.187722] PCI: Cannot allocate resource region 0 of device a000:00:00.0, will remap
[    0.195494] pci a000:00:00.0: BAR 0: no space for [mem size 0x00100000]
[    0.202057] pci a000:00:00.0: BAR 0: failed to assign [mem size 0x00100000]
[    0.208993] pci a000:00:00.0: PCI bridge to [bus 01]
[    0.213933] pci a000:00:00.0:   bridge window [io  0x0000-0xffff]
[    0.220002] pci a000:00:00.0:   bridge window [mem 0x80000000-0x9fffffff]
[    0.226764] pci_bus a000:00: Some PCI device resources are unassigned, try booting with pci=realloc
[    0.235925] /soc@ffe00000/timer@41100: cannot get timer frequency.
[    0.242059] /soc@ffe00000/timer@42100: cannot get timer frequency.
[    0.254462] clocksource: Switched to clocksource timebase
[    0.260493] NET: Registered protocol family 2
[    0.265162] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[    0.272178] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    0.278670] TCP: Hash tables configured (established 8192 bind 8192)
[    0.285022] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.290884] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.297300] NET: Registered protocol family 1
[    2.607509] Crashlog allocated RAM at address 0x3f00000
[    2.612901] workingset: timestamp_bits=30 max_order=18 bucket_order=0
[    2.622935] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    2.628700] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    2.639761] io scheduler noop registered
[    2.643605] io scheduler deadline registered (default)
[    2.649567] pcieport a000:00:00.0: enabling device (0106 -> 0107)
[    2.655875] pcieport a000:00:00.0: AER enabled with IRQ 24
[    2.661445] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
rserial8250.0: ttyS0 at MMIO 0xffe04500 (irq = 42, base_baud = 33333333) is a 16550A
[    2.681148] console [ttyS0] enabled
[    2.681148] console [ttyS0] enabled
[    2.688069] bootconsole [udbg0] disabled
[    2.688069] bootconsole [udbg0] disabled
[    2.696040] serial8250.0: ttyS1 at MMIO 0xffe04600 (irq = 42, base_baud = 33333333) is a 16550A
[    2.705190] console [ttyS0] disabled
[    2.708811] console [ttyS0] enabled
[    2.712565] ffe04600.serial: ttyS1 at MMIO 0xffe04600 (irq = 42, base_baud = 33333333) is a 16550
[    2.722481] Disabling lock debugging due to kernel taint
[    2.722487] fsl-lbc ffe05000.localbus: Chip select error: LTESR 0x00080000
[    2.734643] Machine check in kernel mode.
[    2.738637] Caused by (from MCSR=10008): 
[    2.738640] Bus - Read Data Bus Error
[    2.746282] Oops: Machine check, sig: 7 [#1]
[    2.750535] BE SMP NR_CPUS=2 P2020 RDB
[    2.754272] Modules linked in:
[    2.757319] CPU: 1 PID: 1 Comm: swapper/0 Tainted: G   M            4.14.180 #0
[    2.764610] task: ef448000 task.stack: ef450000
[    2.769125] NIP:  c02995d0 LR: c028f240 CTR: c02995b0
[    2.774161] REGS: effe3f10 TRAP: 0204   Tainted: G   M             (4.14.180)
[    2.781276] MSR:  00029000 <CE,EE,ME>  CR: 24000282  XER: 00000000
[    2.787449] DEAR: f1200000 ESR: 00800000 
[    2.787449] GPR00: c028f524 ef451c20 ef448000 ef451c34 ef49c91c 00000020 ef451cc8 ef451cc8 
[    2.787449] GPR08: 00000002 00000002 f1200000 00000002 24000282 00000000 c049ae20 c049a00c 
[    2.787449] GPR16: c049ad84 c049adc0 c049add8 ef48f158 00000000 c049ad50 ef49c910 01000000 
[    2.787449] GPR24: c049a000 00000000 00000000 00000000 00000000 00000022 00000002 ef49c91c 
[    2.824804] Call Trace:
[    2.827240] [ef451c20] [ef451cd0] 0xef451cd0 (unreliable)
[    2.832625] [ef451c60] [c028f524] 0xc028f524
[    2.836882] [ef451c80] [c028e3dc] 0xc028e3dc
[    2.841138] [ef451cc0] [c02991a8] 0xc02991a8
[    2.845394] [ef451d40] [c028e2b8] 0xc028e2b8
[    2.849651] [ef451d60] [c029993c] 0xc029993c
[    2.853907] [ef451de0] [c0273138] 0xc0273138
[    2.858164] [ef451df0] [c02715b8] 0xc02715b8
[    2.862420] [ef451e20] [c02717f4] 0xc02717f4
[    2.866676] [ef451e40] [c026f634] 0xc026f634
[    2.870933] [ef451e70] [c0270a88] 0xc0270a88
[    2.875189] [ef451e90] [c0272158] 0xc0272158
[    2.879446] [ef451ea0] [c0003140] 0xc0003140
[    2.883702] [ef451f00] [c04d8b40] 0xc04d8b40
[    2.887959] [ef451f30] [c00032d0] 0xc00032d0
[    2.892215] [ef451f40] [c00103b0] 0xc00103b0
[    2.896470] Instruction dump:
[    2.899427] 48000008 0fe00000 7c0004ac 4e800020 81240018 8144000c 2f890001 40be000c 
[    2.907163] 7d2a28ae 48000028 2f890002 40be000c <7d2a2a2e> 48000018 2f890004 409e000c 
[    2.915079] ---[ end trace c9ea2fa8a0ac4ace ]---
[    2.920341] 
[    3.911837] Kernel panic - not syncing: Fatal exception
[    3.917450] Rebooting in 1 seconds..

Is there something wrong I’m doing? Or is this a bug upstream?

Loading...

Available keyboard shortcuts

Tasklist

Task Details

Task Editing