You signed in with another tab or window. Reload to refresh your session.You signed out in another tab or window. Reload to refresh your session.You switched accounts on another tab or window. Reload to refresh your session.Dismiss alert
Versions confirmed on: recent Snapshot, 19.07.3, 18.06.8, 17.01.4
Steps to reproduce:
flash image to sd card, put sd card into pi
turn on wifi radio (uci set wireless.radio0.disabled=0)
add a wireless network such that one is a station and one is a AP (I've tried though gui and command line)
restart wifi (either through reboot or wifi command)
Now in the dmesg you can see wlan0-1 cycling between blocking forwarding and disabled states
Additional info:
I made [[https://forum.openwrt.org/t/raspberry-pi-0-w-as-repeater/65195/2|this forum post]] about it, but not much has come from that and I've learned a lot since posting.
I know that this mode is supported from the iw list output - valid interface combinations:
* #{ managed } <= 1, #{ P2P-device } <= 1, #{ P2P-client, P2P-GO } <= 1,
total <= 3, #channels <= 2
* #{ managed } <= 1, #{ AP } <= 1, #{ P2P-client } <= 1, #{ P2P-device } <= 1,
total <= 4, #channels <= 1
Supported extended features:
* [ 4WAY_HANDSHAKE_STA_PSK ]: 4-way handshake with PSK in station mode
* [ 4WAY_HANDSHAKE_STA_1X ]: 4-way handshake with 802.1X in station mode
I've even gotten AP+STA mode to work by manually starting a second instance of hostapd (note that im not killing the original one), but that makes it even more confusing that it doesn't work normally.
I make sure that they are on the same channel.
If you need anything cleared up please let me know. I've tried for over a week now to fix this myself to no avail.
The text was updated successfully, but these errors were encountered:
I believe the issue has to do with the control interfaces used by hostapd and wpa_supplicant.
In 19.07.3 I found that if I edited /lib/netifd/hostapd.sh such that it starts wpa_supplicant without -H /var/run/hostapd/wlan0-1 at the end, it will work.
this was done by commenting out the line containing "$@" and getting rid of the backslash on the above line
Issue is still present in OpenWRT 21.03.3. I cannot find the lines from the mitigation, probably because "hostapd.sh" has changed. So no working workaround is available.
jaylthegreat:
Supply the following if possible:
device: Raspberry Pi Zero W
Versions confirmed on: recent Snapshot, 19.07.3, 18.06.8, 17.01.4
Steps to reproduce:
flash image to sd card, put sd card into pi
turn on wifi radio (uci set wireless.radio0.disabled=0)
add a wireless network such that one is a station and one is a AP (I've tried though gui and command line)
restart wifi (either through reboot or wifi command)
Now in the dmesg you can see wlan0-1 cycling between blocking forwarding and disabled states
Additional info:
I made [[https://forum.openwrt.org/t/raspberry-pi-0-w-as-repeater/65195/2|this forum post]] about it, but not much has come from that and I've learned a lot since posting.
I know that this mode is supported from the iw list output -
valid interface combinations:
* #{ managed } <= 1, #{ P2P-device } <= 1, #{ P2P-client, P2P-GO } <= 1,
total <= 3, #channels <= 2
* #{ managed } <= 1, #{ AP } <= 1, #{ P2P-client } <= 1, #{ P2P-device } <= 1,
total <= 4, #channels <= 1
Supported extended features:
* [ 4WAY_HANDSHAKE_STA_PSK ]: 4-way handshake with PSK in station mode
* [ 4WAY_HANDSHAKE_STA_1X ]: 4-way handshake with 802.1X in station mode
I've even gotten AP+STA mode to work by manually starting a second instance of hostapd (note that im not killing the original one), but that makes it even more confusing that it doesn't work normally.
I make sure that they are on the same channel.
If you need anything cleared up please let me know. I've tried for over a week now to fix this myself to no avail.
The text was updated successfully, but these errors were encountered: