OpenWrt/LEDE Project

  • Status Unconfirmed
  • Percent Complete
    0%
  • Task Type Bug Report
  • Category Base system
  • Assigned To No-one
  • Operating System All
  • Severity Low
  • Priority Very Low
  • Reported Version Trunk
  • Due in Version Undecided
  • Due Date Undecided
  • Private
Attached to Project: OpenWrt/LEDE Project
Opened by Russell Senior - 29.05.2020

FS#3135 - bcm47xx: WGT634U missing ethernet interface

Supply the following if possible:
- Device problem occurs on: Observed on bcm47xx Netgear WGT634U

- Software versions of OpenWrt/LEDE release, packages, etc:

  1. was working as of r12238-gdc145de4be
  2. noticed broken as of r13317-ga860fe2304

- Steps to reproduce: boot log contains:

[    1.478544] libphy: Fixed MDIO Bus: probed
[    1.483710] b44: Broadcom 44xx/47xx 10/100 PCI ethernet driver version 2.0
[    1.491079] b44 ssb0:0: Required 30BIT DMA mask unsupported by the system

Full log:

[    0.000000] Linux version 4.19.123 (openwrt@hawg) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r13317-a860fe2304)) #0 Thu May 28 19:22:18 2020
[    0.000000] CPU0 revision is: 00029007 (Broadcom BMIPS3300)
[    0.000000] bcm47xx: Using ssb bus
[    0.000000] ssb: Found chip with id 0x5365, rev 0x01 and package 0x00
[    0.000000] early_nvram_init: WGT634U NVRAM found.
[    0.000000] ssb: Sonics Silicon Backplane found at address 0x18000000
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 02000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Primary instruction cache 8kB, VIPT, 2-way, linesize 16 bytes.
[    0.000000] Primary data cache 4kB, 2-way, VIPT, no aliases, linesize 16 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000001ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000001ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000001ffffff]
[    0.000000] On node 0 totalpages: 8192
[    0.000000]   Normal zone: 64 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 8192 pages, LIFO batch:0
[    0.000000] random: get_random_bytes called from 0x803d66c4 with crng_init=0
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0 
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 8128
[    0.000000] Kernel command line:   noinitrd console=ttyS0,115200
[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Memory: 28060K/32768K available (3344K kernel code, 146K rwdata, 428K rodata, 168K init, 268K bss, 4708K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS: 128
[    0.000000] MIPS: machine is Unknown Board
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604467 ns
[    0.000062] sched_clock: 32 bits at 100MHz, resolution 10ns, wraps every 21474836475ns
[    0.000311] Calibrating delay loop... 197.63 BogoMIPS (lpj=395264)
[    0.036686] pid_max: default: 32768 minimum: 301
[    0.038340] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.038541] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.054673] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.054835] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.058075] NET: Registered protocol family 16
[    0.198414] clocksource: Switched to clocksource MIPS
[    0.525333] PCI host bridge to bus 0000:00
[    0.525490] pci_bus 0000:00: root bus resource [mem 0x40000000-0x7fffffff]
[    0.525617] pci_bus 0000:00: root bus resource [io  0x0100-0x07ff]
[    0.525741] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    0.525858] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.526133] pci 0000:00:00.0: [14e4:5365] type 00 class 0x060000
[    0.526507] pci 0000:00:00.0: PCI: Fixing up bridge 0000:00:00.0
[    0.526667] pci 0000:00:00.0: PCI: Fixing up device 0000:00:00.0
[    0.526828] pci 0000:00:00.0: PCI: Fixing latency timer of device 0000:00:00.0 to 168
[    0.527048] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x00001fff]
[    0.527183] pci 0000:00:00.0: reg 0x14: [mem 0x00000000-0x07ffffff pref]
[    0.528677] pci 0000:00:01.0: [168c:0013] type 00 class 0x020000
[    0.528905] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x0000ffff]
[    0.530738] pci 0000:00:02.0: [1033:0035] type 00 class 0x0c0310
[    0.530968] pci 0000:00:02.0: reg 0x10: [mem 0x00000000-0x00000fff]
[    0.531277] pci 0000:00:02.0: supports D1 D2
[    0.531344] pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot
[    0.532723] pci 0000:00:02.1: [1033:0035] type 00 class 0x0c0310
[    0.532950] pci 0000:00:02.1: reg 0x10: [mem 0x00000000-0x00000fff]
[    0.533253] pci 0000:00:02.1: supports D1 D2
[    0.533320] pci 0000:00:02.1: PME# supported from D0 D1 D2 D3hot
[    0.535059] pci 0000:00:02.2: [1033:00e0] type 00 class 0x0c0320
[    0.535288] pci 0000:00:02.2: reg 0x10: [mem 0x00000000-0x000000ff]
[    0.535594] pci 0000:00:02.2: supports D1 D2
[    0.535661] pci 0000:00:02.2: PME# supported from D0 D1 D2 D3hot
[    0.537270] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[    0.537460] pci 0000:00:01.0: BAR 0: assigned [mem 0x40000000-0x4000ffff]
[    0.537673] pci 0000:00:02.0: BAR 0: assigned [mem 0x40010000-0x40010fff]
[    0.537882] pci 0000:00:02.1: BAR 0: assigned [mem 0x40011000-0x40011fff]
[    0.538093] pci 0000:00:02.2: BAR 0: assigned [mem 0x40012000-0x400120ff]
[    0.545771] NET: Registered protocol family 2
[    0.549853] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes)
[    0.550117] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.550613] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.550823] TCP: Hash tables configured (established 1024 bind 1024)
[    0.551768] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.552020] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.553390] NET: Registered protocol family 1
[    0.553846] PCI: CLS 0 bytes, default 16
[    0.591007] Crashlog allocated RAM at address 0x1f00000
[    0.603401] workingset: timestamp_bits=30 max_order=13 bucket_order=0
[    0.654060] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.654400] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.738047] io scheduler noop registered
[    0.738151] io scheduler deadline registered (default)
[    0.739653] Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
[    0.743763] console [ttyS0] disabled
[    0.764156] serial8250.0: ttyS0 at MMIO 0xb8000400 (irq = 3, base_baud = 115740) is a 16550A
[    1.190486] console [ttyS0] enabled
[    1.216366] serial8250.0: ttyS1 at MMIO 0xb8000300 (irq = 3, base_baud = 115740) is a 16550A
[    1.230376] random: fast init done
[    1.234789] physmap platform flash device: 02000001 at 1c000000
[    1.241241] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000089 Chip ID 0x000017
[    1.251850] physmap-flash.0: Found an alias at 0x800000 for the chip at 0x0
[    1.251925] physmap-flash.0: Found an alias at 0x1000000 for the chip at 0x0
[    1.251994] physmap-flash.0: Found an alias at 0x1800000 for the chip at 0x0
[    1.252134] Intel/Sharp Extended Query Table at 0x0031
[    1.257625] Intel/Sharp Extended Query Table at 0x0031
[    1.263094] Using buffer write method
[    1.267053] cfi_cmdset_0001: Erase suspend on write enabled
[    1.272962] erase region 0: offset=0x0,size=0x20000,blocks=64
[    1.282894] 3 bcm47xxpart partitions found on MTD device physmap-flash.0
[    1.289908] Creating 3 MTD partitions on "physmap-flash.0":
[    1.295836] 0x000000000000-0x0000000a0000 : "boot"
[    1.326499] 0x0000000a0000-0x0000007e0000 : "firmware"
[    1.338122] 3 trx partitions found on MTD device firmware
[    1.343853] Creating 3 MTD partitions on "firmware":
[    1.349160] 0x00000000001c-0x000000000948 : "loader"
[    1.372803] 0x000000000948-0x000000149c00 : "linux"
[    1.391736] 0x000000149c00-0x000000740000 : "rootfs"
[    1.403399] mtd: device 4 (rootfs) set to be root filesystem
[    1.409457] 1 squashfs-split partitions found on MTD device rootfs
[    1.416003] 0x000000580000-0x000000740000 : "rootfs_data"
[    1.440832] 0x0000007e0000-0x000000800000 : "nvram"
[    1.478544] libphy: Fixed MDIO Bus: probed
[    1.483710] b44: Broadcom 44xx/47xx 10/100 PCI ethernet driver version 2.0
[    1.491079] b44 ssb0:0: Required 30BIT DMA mask unsupported by the system
[    1.500622] bcm47xx-wdt bcm47xx-wdt.0: BCM47xx Watchdog Timer enabled (30 seconds, Software Timer)
[    1.510716] GPIO_WDT: failed to register misc device
[    1.522701] NET: Registered protocol family 10
[    1.551448] Segment Routing with IPv6
[    1.555920] NET: Registered protocol family 17
[    1.561006] 8021q: 802.1Q VLAN Support v1.8
[    1.587766] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[    1.597826] Freeing unused kernel memory: 168K
[    1.602589] This architecture does not have kernel memory protection.
[    1.609318] Run /sbin/init as init process
[    3.135062] init: Console is alive
[    3.140180] init: - watchdog -
[    5.317770] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    5.476207] usbcore: registered new interface driver usbfs
[    5.482904] usbcore: registered new interface driver hub
[    5.489260] usbcore: registered new device driver usb
[    5.524317] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    5.537667] ehci-platform: EHCI generic platform driver
[    5.557478] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    5.569806] ohci-platform: OHCI generic platform driver
[    5.575871] ohci-platform ohci-platform.0: Generic Platform OHCI controller
[    5.583378] ohci-platform ohci-platform.0: new USB bus registered, assigned bus number 1
[    5.592344] ohci-platform ohci-platform.0: irq 6, io mem 0x18003000
[    5.669187] hub 1-0:1.0: USB hub found
[    5.675894] hub 1-0:1.0: 2 ports detected
[    5.700369] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    5.719972] init: - preinit -
[    7.403807] usb usb1-port1: Cannot enable. Maybe the USB cable is bad?
[    8.478994] usb usb1-port1: Cannot enable. Maybe the USB cable is bad?
[    8.490524] usb usb1-port1: attempt power cycle
[    9.439862] random: jshn: uninitialized urandom read (4 bytes read)
[    9.735569] random: jshn: uninitialized urandom read (4 bytes read)
[    9.870993] usb usb1-port1: Cannot enable. Maybe the USB cable is bad?
[   10.275825] random: jshn: uninitialized urandom read (4 bytes read)
[   10.888504] usb usb1-port1: Cannot enable. Maybe the USB cable is bad?
[   10.959755] usb usb1-port1: unable to enumerate USB device
[   11.166548] usb 1-2: new low-speed USB device number 6 using ohci-platform
[   11.370536] usb 1-2: device descriptor read/64, error -62
[   11.674634] usb 1-2: device descriptor read/64, error -62
[   11.974464] usb 1-2: new low-speed USB device number 7 using ohci-platform
[   12.174454] usb 1-2: device descriptor read/64, error -62
[   12.478455] usb 1-2: device descriptor read/64, error -62
[   12.590748] usb usb1-port2: attempt power cycle
[   13.098467] usb 1-2: new low-speed USB device number 8 using ohci-platform
[   13.522455] usb 1-2: device not accepting address 8, error -62
[   13.714463] usb 1-2: new low-speed USB device number 9 using ohci-platform
[   14.138457] usb 1-2: device not accepting address 9, error -62
[   14.144917] usb usb1-port2: unable to enumerate USB device
[   23.478889] jffs2: notice: (367) jffs2_build_xattr_subsystem: complete building xattr subsystem, 3 of xdatum (0 unchecked, 1 orphan) and 10 of xref (1 dead, 0 orphan) found.
[   23.500379] mount_root: switching to jffs2 overlay
[   23.621417] overlayfs: upper fs does not support tmpfile.
[   23.655639] urandom-seed: Seeding with /etc/urandom.seed
[   23.901849] procd: - early -
[   23.905716] procd: - watchdog -
[   24.967950] procd: - watchdog -
[   24.973710] procd: - ubus -
[   25.100296] random: ubusd: uninitialized urandom read (4 bytes read)
[   25.184997] random: ubusd: uninitialized urandom read (4 bytes read)
[   25.193894] random: ubusd: uninitialized urandom read (4 bytes read)
[   25.210865] procd: - init -
[   29.536216] kmodloader: loading kernel modules from /etc/modules.d/*
[   29.646413] urngd: v1.0.2 started.
[   29.720627] tun: Universal TUN/TAP device driver, 1.6
[   29.908285] Loading modules backported from Linux version v5.7-rc3-0-g6a8b55ed4056
[   29.916172] Backport generated by backports.git v5.7-rc3-1-0-gc0c7d2bb
[   30.362439] xt_time: kernel timezone is -0000
[   30.946473] random: crng init done
[   30.949970] random: 4 urandom warning(s) missed due to ratelimiting
[   31.904075] ath5k 0000:00:01.0: enabling device (0000 -> 0002)
[   31.910410] ath5k 0000:00:01.0: PCI: Fixing up device 0000:00:01.0
[   31.918019] ath5k 0000:00:01.0: registered as 'phy0'
[   32.915035] ath: EEPROM regdomain sanitized
[   32.915095] ath: EEPROM regdomain: 0x64
[   32.915128] ath: EEPROM indicates we should expect a direct regpair map
[   32.915198] ath: Country alpha2 being used: 00
[   32.915231] ath: Regpair used: 0x64
[   32.915568] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   32.929967] ath5k: phy0: Atheros AR5213A chip found (MAC: 0x59, PHY: 0x43)
[   32.937191] ath5k: phy0: RF2112B 2GHz radio found (0x46)
[   33.115785] kmodloader: done loading kernel modules from /etc/modules.d/*


Loading...

Available keyboard shortcuts

Tasklist

Task Details

Task Editing