You signed in with another tab or window. Reload to refresh your session.You signed out in another tab or window. Reload to refresh your session.You switched accounts on another tab or window. Reload to refresh your session.Dismiss alert
OpenWrt 19.07.1 on BT HomeHub5A (lantiq vrx200) the dsl stats report tool (ltq-vdsl-app_4.17.18.6-2_mips_24kc.ipk) and the matching kerel module (kmod-ltq-vdsl-vr9-mei_4.14.167+1.5.17.6-4_mips_24kc.ipk) do not report ITU G.998.4 Retransmission counts (on lines using G.INP retransmissions. It turns out that adding:
CONFIGURE_ARGS += \
--enable-dsl-pm-retx-counters \
--enable-dsl-pm-retx-thresholds
to openwrt/package/kernel/lantiq/ltq-vdsl/Makefile and openwrt/package/network/config/ltq-vdsl-app/Makefile and rebuilding yields a working ReTx counter report:
At least in Germany the incumbent uses G.998.4 Retransmission, not only do deal with impulse noise, but also as a diagnostic counters for its Dynamik Link/Spektrum Management tool that based on these and other counters will limit the maximum perissable Sync for each line to optimize lik stability. It would be really great if stock OpenWrt builds would alow to report these values and I would like to propose to change the makefiles as shown above.
The text was updated successfully, but these errors were encountered:
Here is a patch to get the required changes into the two relevant packages: diff --git a/package/kernel/lantiq/ltq-vdsl/Makefile b/package/kernel/lantiq/ltq-vdsl/Makefile
index cf3711beb7..e42f191343 100644
--- a/package/kernel/lantiq/ltq-vdsl/Makefile
+++ b/package/kernel/lantiq/ltq-vdsl/Makefile
@@ -69,6 +69,10 @@ CONFIGURE_ARGS += --enable-model=full
#CONFIGURE_ARGS += --enable-model=typical
#CONFIGURE_ARGS += --enable-model=debug
moeller0:
OpenWrt 19.07.1 on BT HomeHub5A (lantiq vrx200) the dsl stats report tool (ltq-vdsl-app_4.17.18.6-2_mips_24kc.ipk) and the matching kerel module (kmod-ltq-vdsl-vr9-mei_4.14.167+1.5.17.6-4_mips_24kc.ipk) do not report ITU G.998.4 Retransmission counts (on lines using G.INP retransmissions. It turns out that adding:
CONFIGURE_ARGS += \
--enable-dsl-pm-retx-counters \
--enable-dsl-pm-retx-thresholds
to openwrt/package/kernel/lantiq/ltq-vdsl/Makefile and openwrt/package/network/config/ltq-vdsl-app/Makefile and rebuilding yields a working ReTx counter report:
root@BTHH5A:
# . /lib/functions/lantiq_dsl.sh ; dsl_cmd rtsg 0# . /lib/functions/lantiq_dsl.sh ; dsl_cmd rtsg 1nReturn=0 nDirection=0 nRxCorruptedTotal=0 nRxUncorrectedProtected=0 nRxRetransmitted=0 nRxCorrected=0 nTxRetransmitted=3
root@ BTHH5A:
nReturn=0 nDirection=1 nRxCorruptedTotal=7114893 nRxUncorrectedProtected=6171968 nRxRetransmitted=0 nRxCorrected=942925 nTxRetransmitted=9228892
At least in Germany the incumbent uses G.998.4 Retransmission, not only do deal with impulse noise, but also as a diagnostic counters for its Dynamik Link/Spektrum Management tool that based on these and other counters will limit the maximum perissable Sync for each line to optimize lik stability. It would be really great if stock OpenWrt builds would alow to report these values and I would like to propose to change the makefiles as shown above.
The text was updated successfully, but these errors were encountered: