You signed in with another tab or window. Reload to refresh your session.You signed out in another tab or window. Reload to refresh your session.You switched accounts on another tab or window. Reload to refresh your session.Dismiss alert
Testing using OpenWrt 19.07-SNAPSHOT r10233-4a7a8d93fa, ath79 image, connected via wifi
removing both eth0 & eth1 from their interface, rebooting, then doing
ip l set up eth0
ip l set up eth1
eth0 (lan port) is always up even if no cables are connected (state UP, no NO-CARRIER)
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP mode DEFAULT group default qlen 1000
link/ether e4:95:6e:45:32:f8 brd ff:ff:ff:ff:ff:ff
3: eth1: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc fq_codel state DOWN mode DEFAULT group default qlen 1000
link/ether e4:95:6e:45:32:f8 brd ff:ff:ff:ff:ff:ff
I would say it's a know bug because the led is configured to look at the switch and not the interface
ar71xx images are working ok
here part of the dmesg for ath79
[ 0.745353] ag71xx 19000000.eth: Could not connect to PHY device. Deferring probe.
[ 1.480124] ag71xx 1a000000.eth: connected to PHY at fixed-0:00 [uid=00000000, driver=Generic PHY]
[ 1.488671] eth0: Atheros AG71xx at 0xba000000, irq 5, mode: gmii
[ 1.865945] ag71xx 19000000.eth: connected to PHY at mdio-bus.0:1f:04 [uid=004dd041, driver=Generic PHY]
[ 1.875354] eth1: Atheros AG71xx at 0xb9000000, irq 4, mode: mii
and for ar71xx
[ 1.571027] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[ 2.244049] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
the 2 ports are switched between ar71xx and ath79 images
I've tried to randomly change the dts, but I have no idea what I'm doing ...
The text was updated successfully, but these errors were encountered:
Typically, one of the ports has to be set up with the netdev and one with the switch. But I never remember which one ...
Despite, it would be possible that the 0x02 is wrong. But essentially, all you need to change should be those two lines.
champtar:
Hello Team
Testing using OpenWrt 19.07-SNAPSHOT r10233-4a7a8d93fa, ath79 image, connected via wifi
removing both eth0 & eth1 from their interface, rebooting, then doing
ip l set up eth0
ip l set up eth1
eth0 (lan port) is always up even if no cables are connected (state UP, no NO-CARRIER)
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP mode DEFAULT group default qlen 1000
link/ether e4:95:6e:45:32:f8 brd ff:ff:ff:ff:ff:ff
3: eth1: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc fq_codel state DOWN mode DEFAULT group default qlen 1000
link/ether e4:95:6e:45:32:f8 brd ff:ff:ff:ff:ff:ff
I would say it's a know bug because the led is configured to look at the switch and not the interface
ar71xx images are working ok
here part of the dmesg for ath79
[ 0.745353] ag71xx 19000000.eth: Could not connect to PHY device. Deferring probe.
[ 1.480124] ag71xx 1a000000.eth: connected to PHY at fixed-0:00 [uid=00000000, driver=Generic PHY]
[ 1.488671] eth0: Atheros AG71xx at 0xba000000, irq 5, mode: gmii
[ 1.865945] ag71xx 19000000.eth: connected to PHY at mdio-bus.0:1f:04 [uid=004dd041, driver=Generic PHY]
[ 1.875354] eth1: Atheros AG71xx at 0xb9000000, irq 4, mode: mii
and for ar71xx
[ 1.571027] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[ 2.244049] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
the 2 ports are switched between ar71xx and ath79 images
I've tried to randomly change the dts, but I have no idea what I'm doing ...
The text was updated successfully, but these errors were encountered: