OpenWrt/LEDE Project

  • Status Unconfirmed
  • Percent Complete
    0%
  • Task Type Bug Report
  • Category Base system
  • Assigned To No-one
  • Operating System All
  • Severity Low
  • Priority Very Low
  • Reported Version Trunk
  • Due in Version Undecided
  • Due Date Undecided
  • Private
Attached to Project: OpenWrt/LEDE Project
Opened by Sinan Çetinkaya - 27.06.2019

FS#2342 - mt7621 "PCIE2 no card" error at cold boot

Supply the following if possible:
- Device problem occurs on

root@OpenWrt:~# cat /etc/*-release
NAME="OpenWrt"
VERSION="SNAPSHOT"
ID="openwrt"
ID_LIKE="lede openwrt"
PRETTY_NAME="OpenWrt SNAPSHOT"
VERSION_ID="snapshot"
HOME_URL="https://openwrt.org/"
BUG_URL="https://bugs.openwrt.org/"
SUPPORT_URL="https://forum.openwrt.org/"
BUILD_ID="r10327-a0e5ca4f35"
LEDE_BOARD="ramips/mt7621"
LEDE_ARCH="mipsel_24kc"
LEDE_TAINTS=""
LEDE_DEVICE_MANUFACTURER="OpenWrt"
LEDE_DEVICE_MANUFACTURER_URL="https://openwrt.org/"
LEDE_DEVICE_PRODUCT="Generic"
LEDE_DEVICE_REVISION="v0"
LEDE_RELEASE="OpenWrt SNAPSHOT r10327-a0e5ca4f35"

- Software versions of OpenWrt/LEDE release, packages, etc.

root@OpenWrt:~# opkg list-installed
base-files - 200-r10327-a0e5ca4f35
block-mount - 2019-03-28-ff1ded63-5
busybox - 1.31.0-1
dnsmasq - 2.80-13
dropbear - 2019.78-2
firewall - 2019-01-02-70f8785b-2
fstools - 2019-03-28-ff1ded63-5
fwtool - 1
getrandom - 2019-06-16-4df34a4d-2
hostapd-common - 2018-12-02-c2c6c01b-6
htop - 2.2.0-2
ip6tables - 1.8.2-3
iperf3 - 3.6-1
iptables - 1.8.2-3
iptables-mod-conntrack-extra - 1.8.2-3
iptables-mod-ipopt - 1.8.2-3
iw-full - 5.0.1-1
jshn - 2019-06-16-ecf56174-1
jsonfilter - 2018-02-04-c7e938d6-1
kernel - 4.14.129-1-2c88b7be5bf978d41a9f6038dabdd3b4
kmod-ata-ahci - 4.14.129-1
kmod-ata-core - 4.14.129-1
kmod-cfg80211 - 4.14.129+4.19.32-1-2
kmod-crypto-crc32c - 4.14.129-1
kmod-crypto-hash - 4.14.129-1
kmod-fs-ext4 - 4.14.129-1
kmod-gpio-button-hotplug - 4.14.129-2
kmod-ifb - 4.14.129-1
kmod-ip6tables - 4.14.129-1
kmod-ipt-conntrack - 4.14.129-1
kmod-ipt-conntrack-extra - 4.14.129-1
kmod-ipt-core - 4.14.129-1
kmod-ipt-ipopt - 4.14.129-1
kmod-ipt-nat - 4.14.129-1
kmod-ipt-offload - 4.14.129-1
kmod-ipt-raw - 4.14.129-1
kmod-leds-gpio - 4.14.129-1
kmod-lib-crc-ccitt - 4.14.129-1
kmod-lib-crc16 - 4.14.129-1
kmod-mac80211 - 4.14.129+4.19.32-1-2
kmod-mmc - 4.14.129-1
kmod-mt76 - 4.14.129+2019-06-25-d680ab01-1
kmod-mt76-core - 4.14.129+2019-06-25-d680ab01-1
kmod-mt7603 - 4.14.129+2019-06-25-d680ab01-1
kmod-mt76x02-common - 4.14.129+2019-06-25-d680ab01-1
kmod-mt76x2 - 4.14.129+2019-06-25-d680ab01-1
kmod-mt76x2-common - 4.14.129+2019-06-25-d680ab01-1
kmod-nf-conntrack - 4.14.129-1
kmod-nf-conntrack6 - 4.14.129-1
kmod-nf-flow - 4.14.129-1
kmod-nf-ipt - 4.14.129-1
kmod-nf-ipt6 - 4.14.129-1
kmod-nf-nat - 4.14.129-1
kmod-nf-reject - 4.14.129-1
kmod-nf-reject6 - 4.14.129-1
kmod-nls-base - 4.14.129-1
kmod-ppp - 4.14.129-1
kmod-pppoe - 4.14.129-1
kmod-pppox - 4.14.129-1
kmod-sched-cake - 4.14.129+2019-03-12-057c7388-1
kmod-sched-core - 4.14.129-1
kmod-scsi-core - 4.14.129-1
kmod-sdhci-mt7620 - 4.14.129-1
kmod-slhc - 4.14.129-1
kmod-usb-core - 4.14.129-1
kmod-usb-storage - 4.14.129-1
kmod-usb-storage-uas - 4.14.129-1
kmod-usb3 - 4.14.129-1
libblobmsg-json - 2019-06-16-ecf56174-1
libc - 1.1.22-1
libelf1 - 0.176-2
libgcc1 - 7.4.0-1
libip4tc0 - 1.8.2-3
libip6tc0 - 1.8.2-3
libiwinfo-lua - 2019-06-12-1372f47e-1
libiwinfo20181126 - 2019-06-12-1372f47e-1
libjson-c4 - 0.13.1-1
libjson-script - 2019-06-16-ecf56174-1
libkmod - 20-1
liblua5.1.5 - 5.1.5-3
liblucihttp-lua - 2019-06-05-91c01c3c-1
liblucihttp0 - 2019-06-05-91c01c3c-1
libmnl0 - 1.0.4-2
libncurses6 - 6.1-4
libnl-tiny - 0.1-5
libpci - 3.6.2-3
libpthread - 1.1.22-1
librt - 1.1.22-1
libubox20170601 - 2019-06-16-ecf56174-1
libubus-lua - 2018-10-06-221ce7e7-1
libubus20170705 - 2018-10-06-221ce7e7-1
libuci20130104 - 2019-05-17-f199b961-3
libuclient20160123 - 2019-05-30-3b3e368d-1
libusb-1.0-0 - 1.0.22-2
libxtables12 - 1.8.2-3
logd - 2019-06-16-4df34a4d-2
lua - 5.1.5-3
luci - git-19.175.17568-86fd703-1
luci-app-firewall - git-19.175.17568-86fd703-1
luci-app-opkg - git-19.175.17568-86fd703-1
luci-app-samba - git-19.175.17568-86fd703-1
luci-app-sqm - 1.3.0-1
luci-base - f138fc93-1
luci-lib-ip - git-19.175.17568-86fd703-1
luci-lib-jsonc - git-19.175.17568-86fd703-1
luci-lib-nixio - git-19.175.17568-86fd703-1
luci-mod-admin-full - git-19.175.17568-86fd703-1
luci-mod-network - git-19.175.17568-86fd703-1
luci-mod-status - git-19.175.17568-86fd703-1
luci-mod-system - git-19.175.17568-86fd703-1
luci-proto-ipv6 - git-19.175.17568-86fd703-1
luci-proto-ppp - git-19.175.17568-86fd703-1
luci-theme-bootstrap - git-19.175.17568-86fd703-1
luci-wrtbwmon - v0.8.3
mtd - 24
nano - 4.3-1
netifd - 2019-06-15-9932ed02-1
odhcp6c - 2019-01-11-d2e247d8-16
odhcpd-ipv6only - 2019-05-17-41a74cba-3
openwrt-keyring - 2018-05-18-103a32e9-1
opkg - 2019-06-14-dcbc142e-1
pciutils - 3.6.2-3
ppp - 2.4.7.git-2019-05-25-2
ppp-mod-pppoe - 2.4.7.git-2019-05-25-2
procd - 2019-05-30-ade00ca5-1
rpcd - 2019-06-05-89bfaa42-2
rpcd-mod-rrdns - 20170710
samba36-server - 3.6.25-14
sqm-scripts - 1.3.0-1
swconfig - 12
tc - 5.0.0-2
terminfo - 6.1-4
ubi-utils - 2.0.2-1
ubox - 2019-06-16-4df34a4d-2
ubus - 2018-10-06-221ce7e7-1
ubusd - 2018-10-06-221ce7e7-1
uci - 2019-05-17-f199b961-3
uclient-fetch - 2019-05-30-3b3e368d-1
uhttpd - 2019-06-16-91fcac34-3
urandom-seed - 1.0-1
urngd - 2019-06-17-c057e177-1
usbutils - 007-10
usign - 2015-07-04-ef641914-1
wireless-regdb - 2017-10-20-4343d359
wpad-mini - 2018-12-02-c2c6c01b-6
wrtbwmon - 0.36
zlib - 1.2.11-3

- Steps to reproduce

I have UniElec U7621-06 router with 3 miniPCIe slots. PCIE2 slot gets not detected when the device boots from cold boot.
When I reboot the device from LuCi (warm boot) it works fine.

root@OpenWrt:~# lspci
00:00.0 PCI bridge: Device 0e8d:0801 (rev 01)
00:01.0 PCI bridge: Device 0e8d:0801 (rev 01)
00:02.0 PCI bridge: Device 0e8d:0801 (rev 01)
01:00.0 SATA controller: ASMedia Technology Inc. ASM1062 Serial ATA Controller (rev 01)
02:00.0 Network controller: MEDIATEK Corp. Device 7612
03:00.0 Network controller: MEDIATEK Corp. Device 7602
Sinan Çetinkaya commented on 27.06.2019 13:37

dmesg

[    0.000000] Linux version 4.14.129 (buildbot@602ce18687ab) (gcc version 7.4.0 (OpenWrt GCC 7.4.0 r10327-a0e5ca4f35)) #0 SMP Tue Jun 25 11:24:49 2019
[    0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[    0.000000] MIPS: machine is UniElec U7621-06 (256M RAM/16M flash)
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 10000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] VPE topology {2,2} total 4
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x000000000fffffff]
[    0.000000]   HighMem  empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x000000000fffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff]
[    0.000000] On node 0 totalpages: 65536
[    0.000000] free_area_init_node: node 0, pgdat 80634860, node_mem_map 81003000
[    0.000000]   Normal zone: 576 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 65536 pages, LIFO batch:15
[    0.000000] random: get_random_bytes called from start_kernel+0x9c/0x4e0 with crng_init=0
[    0.000000] percpu: Embedded 14 pages/cpu s26128 r8192 d23024 u57344
[    0.000000] pcpu-alloc: s26128 r8192 d23024 u57344 alloc=14*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 64960
[    0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2
[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Writing ErrCtl register=00051c0f
[    0.000000] Readback ErrCtl register=00051c0f
[    0.000000] Memory: 252456K/262144K available (5018K kernel code, 261K rwdata, 1076K rodata, 224K init, 260K bss, 9688K reserved, 0K cma-reserved, 0K highmem)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS: 256
[    0.000000] CPU Clock: 880MHz
[    0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns
[    0.000010] sched_clock: 32 bits at 440MHz, resolution 2ns, wraps every 4880645118ns
[    0.007838] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688)
[    0.073997] pid_max: default: 32768 minimum: 301
[    0.078840] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.085351] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.094785] Hierarchical SRCU implementation.
[    0.100086] smp: Bringing up secondary CPUs ...
[    0.041035] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.041044] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.041057] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    0.041213] CPU1 revision is: 0001992f (MIPS 1004Kc)
[    0.164894] Synchronize counters for CPU 1: done.
[    8.236089] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    8.236098] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    8.236106] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    8.236188] CPU2 revision is: 0001992f (MIPS 1004Kc)
[    0.256364] Synchronize counters for CPU 2: done.
[    2.674101] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    2.674111] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    2.674120] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    2.674210] CPU3 revision is: 0001992f (MIPS 1004Kc)
[    0.341550] Synchronize counters for CPU 3: done.
[    0.371421] smp: Brought up 1 node, 4 CPUs
[    0.379810] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.389591] futex hash table entries: 1024 (order: 3, 32768 bytes)
[    0.396043] pinctrl core: initialized pinctrl subsystem
[    0.402986] NET: Registered protocol family 16
[    0.418679] FPU Affinity set after 11720 emulations
[    0.419710] pull PCIe RST: RALINK_RSTCTRL = 4000000
[    0.725007] release PCIe RST: RALINK_RSTCTRL = 7000000
[    0.730055] ***** Xtal 40MHz *****
[    0.733414] release PCIe RST: RALINK_RSTCTRL = 7000000
[    0.738506] Port 0 N_FTS = 1b102800
[    0.741978] Port 1 N_FTS = 1b102800
[    0.745418] Port 2 N_FTS = 1b102800
[    1.900907] PCIE2 no card, disable it(RST&CLK)
[    1.905274]  -> 21007f2
[    1.907668] PCIE0 enabled
[    1.910259] PCIE1 enabled
[    1.912868] PCI host bridge /pcie@1e140000 ranges:
[    1.917641]  MEM 0x0000000060000000..0x000000006fffffff
[    1.922800]   IO 0x000000001e160000..0x000000001e16ffff
[    1.928003] PCI coherence region base: 0xbfbf8000, mask/settings: 0x60000000
[    1.945908] mt7621_gpio 1e000600.gpio: registering 32 gpios
[    1.951712] mt7621_gpio 1e000600.gpio: registering 32 gpios
[    1.957553] mt7621_gpio 1e000600.gpio: registering 32 gpios
[    1.964780] PCI host bridge to bus 0000:00
[    1.968864] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[    1.975630] pci_bus 0000:00: root bus resource [io  0xffffffff]
[    1.981522] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    1.988248] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    1.996181] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400
[    1.996224] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[    1.996236] pci 0000:00:00.0: reg 0x14: [mem 0x00000000-0x0000ffff]
[    1.996305] pci 0000:00:00.0: supports D1
[    1.996314] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[    1.996567] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400
[    1.996596] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[    1.996609] pci 0000:00:01.0: reg 0x14: [mem 0x00000000-0x0000ffff]
[    1.996668] pci 0000:00:01.0: supports D1
[    1.996677] pci 0000:00:01.0: PME# supported from D0 D1 D3hot
[    1.996921] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    2.004825] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    2.012984] pci 0000:01:00.0: [1b21:0612] type 00 class 0x010601
[    2.013035] pci 0000:01:00.0: reg 0x10: [io  0x0000-0x0007]
[    2.013051] pci 0000:01:00.0: reg 0x14: [io  0x0000-0x0003]
[    2.013068] pci 0000:01:00.0: reg 0x18: [io  0x0000-0x0007]
[    2.013085] pci 0000:01:00.0: reg 0x1c: [io  0x0000-0x0003]
[    2.013102] pci 0000:01:00.0: reg 0x20: [io  0x0000-0x001f]
[    2.013119] pci 0000:01:00.0: reg 0x24: [mem 0x00000000-0x000001ff]
[    2.013136] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[    2.013403] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[    2.013598] pci 0000:02:00.0: [14c3:7612] type 00 class 0x028000
[    2.013657] pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit]
[    2.013704] pci 0000:02:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[    2.013800] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
[    2.013985] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[    2.014005] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 02
[    2.014078] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[    2.020594] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[    2.027527] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000]
[    2.034071] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000]
[    2.040999] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[    2.047719] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x601fffff pref]
[    2.054912] pci 0000:00:01.0: BAR 8: assigned [mem 0x60200000-0x602fffff]
[    2.061635] pci 0000:00:01.0: BAR 9: assigned [mem 0x60300000-0x603fffff pref]
[    2.068822] pci 0000:00:00.0: BAR 1: assigned [mem 0x60400000-0x6040ffff]
[    2.075552] pci 0000:00:01.0: BAR 1: assigned [mem 0x60410000-0x6041ffff]
[    2.082300] pci 0000:00:00.0: BAR 7: no space for [io  size 0x1000]
[    2.088497] pci 0000:00:00.0: BAR 7: failed to assign [io  size 0x1000]
[    2.095098] pci 0000:01:00.0: BAR 6: assigned [mem 0x60100000-0x6010ffff pref]
[    2.102243] pci 0000:01:00.0: BAR 5: assigned [mem 0x60000000-0x600001ff]
[    2.108997] pci 0000:01:00.0: BAR 4: no space for [io  size 0x0020]
[    2.115200] pci 0000:01:00.0: BAR 4: failed to assign [io  size 0x0020]
[    2.121779] pci 0000:01:00.0: BAR 0: no space for [io  size 0x0008]
[    2.127982] pci 0000:01:00.0: BAR 0: failed to assign [io  size 0x0008]
[    2.134569] pci 0000:01:00.0: BAR 2: no space for [io  size 0x0008]
[    2.140769] pci 0000:01:00.0: BAR 2: failed to assign [io  size 0x0008]
[    2.147357] pci 0000:01:00.0: BAR 1: no space for [io  size 0x0004]
[    2.153562] pci 0000:01:00.0: BAR 1: failed to assign [io  size 0x0004]
[    2.160143] pci 0000:01:00.0: BAR 3: no space for [io  size 0x0004]
[    2.166347] pci 0000:01:00.0: BAR 3: failed to assign [io  size 0x0004]
[    2.172933] pci 0000:00:00.0: PCI bridge to [bus 01]
[    2.177840] pci 0000:00:00.0:   bridge window [mem 0x60000000-0x600fffff]
[    2.184592] pci 0000:00:00.0:   bridge window [mem 0x60100000-0x601fffff pref]
[    2.191765] pci 0000:02:00.0: BAR 0: assigned [mem 0x60200000-0x602fffff 64bit]
[    2.199038] pci 0000:02:00.0: BAR 6: assigned [mem 0x60300000-0x6030ffff pref]
[    2.206179] pci 0000:00:01.0: PCI bridge to [bus 02]
[    2.211117] pci 0000:00:01.0:   bridge window [mem 0x60200000-0x602fffff]
[    2.217845] pci 0000:00:01.0:   bridge window [mem 0x60300000-0x603fffff pref]
[    2.226485] clocksource: Switched to clocksource GIC
[    2.233369] NET: Registered protocol family 2
[    2.238493] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[    2.245380] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
[    2.251830] TCP: Hash tables configured (established 2048 bind 2048)
[    2.258311] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    2.264080] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    2.270574] NET: Registered protocol family 1
[    2.274901] PCI: CLS 0 bytes, default 32
[    2.506432] 4 CPUs re-calibrate udelay(lpj = 2924544)
[    2.513141] Crashlog allocated RAM at address 0x3f00000
[    2.518607] workingset: timestamp_bits=14 max_order=16 bucket_order=2
[    2.528188] random: fast init done
[    2.537983] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    2.543734] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    2.558006] io scheduler noop registered
[    2.561848] io scheduler deadline registered (default)
[    2.567705] gpio-export gpio-export: 1 gpio(s) exported
[    2.573703] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    2.583908] console [ttyS0] disabled
[    2.587559] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 18, base_baud = 3125000) is a 16550A
[    2.596553] console [ttyS0] enabled
[    2.603406] bootconsole [early0] disabled
[    2.612364] cacheinfo: Unable to detect cache hierarchy for CPU 0
[    2.619499] MediaTek Nand driver init, version v2.1 Fix AHB virt2phys error
[    2.627019] spi-mt7621 1e000b00.spi: sys_freq: 220000000
[    2.633248] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
[    2.638392] 4 fixed-partitions partitions found on MTD device spi0.0
[    2.644713] Creating 4 MTD partitions on "spi0.0":
[    2.649528] 0x000000000000-0x000000030000 : "bootloader"
[    2.655997] 0x000000030000-0x000000040000 : "config"
[    2.662200] 0x000000040000-0x000000050000 : "factory"
[    2.668554] 0x000000050000-0x000001000000 : "firmware"
[    2.675156] 2 uimage-fw partitions found on MTD device firmware
[    2.681134] Creating 2 MTD partitions on "firmware":
[    2.686095] 0x000000000000-0x0000001fe5ff : "kernel"
[    2.692313] 0x0000001fe5ff-0x000000fb0000 : "rootfs"
[    2.698376] mtd: device 5 (rootfs) set to be root filesystem
[    2.704141] 1 squashfs-split partitions found on MTD device rootfs
[    2.710376] 0x0000003a0000-0x000000fb0000 : "rootfs_data"
[    2.717690] libphy: Fixed MDIO Bus: probed
[    2.788520] libphy: mdio: probed
[    4.192213] mtk_soc_eth 1e100000.ethernet: loaded mt7530 driver
[    4.198993] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 21
[    4.210155] NET: Registered protocol family 10
[    4.216367] Segment Routing with IPv6
[    4.220207] NET: Registered protocol family 17
[    4.224726] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    4.237642] 8021q: 802.1Q VLAN Support v1.8
[    4.244507] hctosys: unable to open rtc device (rtc0)
[    4.255947] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[    4.263581] Freeing unused kernel memory: 224K
[    4.268066] This architecture does not have kernel memory protection.
[    4.515115] mtk_soc_eth 1e100000.ethernet eth0: port 4 link up
[    4.876070] init: Console is alive
[    4.879795] init: - watchdog -
[    5.536265] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    5.665282] usbcore: registered new interface driver usbfs
[    5.670914] usbcore: registered new interface driver hub
[    5.676384] usbcore: registered new device driver usb
[    5.690693] SCSI subsystem initialized
[    5.706690] libata version 3.00 loaded.
[    5.709965] bus=0x1, slot = 0x0, irq=0x0
[    5.713918] ahci 0000:01:00.0: version 3.0
[    5.713942] PCI: Enabling device 0000:00:00.0 (0004 -> 0006)
[    5.719788] ahci 0000:01:00.0: SSS flag set, parallel bus scan disabled
[    5.726474] ahci 0000:01:00.0: AHCI 0001.0200 32 slots 2 ports 6 Gbps 0x3 impl SATA mode
[    5.734541] ahci 0000:01:00.0: flags: 64bit ncq sntf stag led clo pmp pio slum part ccc sxs 
[    5.745445] scsi host0: ahci
[    5.749197] scsi host1: ahci
[    5.752450] ata1: SATA max UDMA/133 abar m512@0x60000000 port 0x60000100 irq 23
[    5.759803] ata2: SATA max UDMA/133 abar m512@0x60000000 port 0x60000180 irq 23
[    6.106494] ata1: SATA link down (SStatus 0 SControl 300)
[    6.126958] mtk_soc_eth 1e100000.ethernet eth0: port 0 link up
[    6.446478] ata2: SATA link down (SStatus 0 SControl 300)
[    6.458505] xhci-mtk 1e1c0000.xhci: 1e1c0000.xhci supply vbus not found, using dummy regulator
[    6.467271] xhci-mtk 1e1c0000.xhci: 1e1c0000.xhci supply vusb33 not found, using dummy regulator
[    6.476214] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
[    6.481568] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 1
[    6.496644] xhci-mtk 1e1c0000.xhci: hcc params 0x01401198 hci version 0x96 quirks 0x0000000000210010
[    6.505828] xhci-mtk 1e1c0000.xhci: irq 20, io mem 0x1e1c0000
[    6.512697] hub 1-0:1.0: USB hub found
[    6.516595] hub 1-0:1.0: 2 ports detected
[    6.521296] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
[    6.526674] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 2
[    6.534140] xhci-mtk 1e1c0000.xhci: Host supports USB 3.0  SuperSpeed
[    6.540766] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[    6.549789] hub 2-0:1.0: USB hub found
[    6.553618] hub 2-0:1.0: 1 port detected
[    6.630771] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    6.656894] init: - preinit -
[    6.766843] mmc0: new high speed SD card at address b368
[    6.773330] mmcblk0: mmc0:b368 UD    487 MiB 
[    6.779944]  mmcblk0: p1
[    7.515441] mtk_soc_eth 1e100000.ethernet: PPE started
[    7.597830] random: procd: uninitialized urandom read (4 bytes read)
[   10.947501] jffs2: notice: (535) jffs2_build_xattr_subsystem: complete building xattr subsystem, 10 of xdatum (3 unchecked, 7 orphan) and 71 of xref (7 dead, 0 orphan) found.
[   10.987902] mount_root: loading kmods from internal overlay
[   11.852189] kmodloader: loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
[   12.234133] usbcore: registered new interface driver usb-storage
[   12.246044] usbcore: registered new interface driver uas
[   12.251705] kmodloader: done loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
[   12.557371] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[   12.569877] block: extroot: not configured
[   12.607865] mount_root: switching to jffs2 overlay
[   12.630565] overlayfs: upper fs does not support tmpfile.
[   12.641521] urandom-seed: Seeding with /etc/urandom.seed
[   12.753264] mtk_soc_eth 1e100000.ethernet: 0x100 = 0x6060000c, 0x10c = 0x80818
[   12.781923] procd: - early -
[   12.784913] procd: - watchdog -
[   12.926020] random: crng init done
[   13.381827] EXT4-fs (mmcblk0p1): warning: maximal mount count reached, running e2fsck is recommended
[   13.397321] EXT4-fs (mmcblk0p1): recovery complete
[   13.402133] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: 
[   13.496761] procd: - watchdog -
[   13.500452] procd: - ubus -
[   13.584178] procd: - init -
[   14.215181] urngd: v1.0.0 started.
[   14.227110] kmodloader: loading kernel modules from /etc/modules.d/*
[   14.245448] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   14.257699] Mirror/redirect action on
[   14.279894] u32 classifier
[   14.282639]     input device check on
[   14.286292]     Actions configured
[   14.321189] nf_conntrack version 0.5.0 (4096 buckets, 16384 max)
[   14.350722] Loading modules backported from Linux version v4.19.32-0-g3a2156c839c7
[   14.358349] Backport generated by backports.git v4.19.32-1-0-g1c4f7569
[   14.367738] ip_tables: (C) 2000-2006 Netfilter Core Team
[   14.472422] xt_time: kernel timezone is -0000
[   15.093750] bus=0x2, slot = 0x1, irq=0xff
[   15.097887] PCI: Enabling device 0000:00:01.0 (0004 -> 0006)
[   15.103718] mt76x2e 0000:02:00.0: ASIC revision: 76120044
[   15.800462] mt76x2e 0000:02:00.0: ROM patch build: 20141115060606a
[   15.902849] mt76x2e 0000:02:00.0: Firmware Version: 0.0.00
[   15.908364] mt76x2e 0000:02:00.0: Build: 1
[   15.912441] mt76x2e 0000:02:00.0: Build Time: 201507311614____
[   15.936490] mt76x2e 0000:02:00.0: Firmware running!
[   15.944597] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   15.953566] PPP generic driver version 2.4.2
[   15.959669] NET: Registered protocol family 24
[   15.967692] kmodloader: done loading kernel modules from /etc/modules.d/*
[   22.725723] mtk_soc_eth 1e100000.ethernet: PPE started
[   22.739771] br-lan: port 1(eth0.1) entered blocking state
[   22.745237] br-lan: port 1(eth0.1) entered disabled state
[   22.751764] device eth0.1 entered promiscuous mode
[   22.756984] device eth0 entered promiscuous mode
[   22.765609] br-lan: port 1(eth0.1) entered blocking state
[   22.771119] br-lan: port 1(eth0.1) entered forwarding state
[   22.777397] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   23.727457] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   26.313797] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   26.324622] br-lan: port 2(wlan0) entered blocking state
[   26.330008] br-lan: port 2(wlan0) entered disabled state
[   26.335972] device wlan0 entered promiscuous mode
[   91.194176] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   91.200949] br-lan: port 2(wlan0) entered blocking state
[   91.206256] br-lan: port 2(wlan0) entered forwarding state

Loading...

Available keyboard shortcuts

Tasklist

Task Details

Task Editing