You signed in with another tab or window. Reload to refresh your session.You signed out in another tab or window. Reload to refresh your session.You switched accounts on another tab or window. Reload to refresh your session.Dismiss alert
Current trunk (reboot-10086-g62940df3a9) bricks TPLINK 1043ND v1, two devices.
U-Boot 1.1.4 (Sep 15 2009 - 09:41:38)
AP83 (ar9100) U-boot 0.0.11
DRAM:
sri
32 MB
id read 0x100000ff
flash size 8MB, sector count = 128
Flash: 8 MB
Using default environment
In: serial
Out: serial
Err: serial
Net: ag7100_enet_initialize...
No valid address in Flash. Using fixed address
: cfg1 0xf cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
eth0 up
eth0
Autobooting in 1 secondsar7100>
ar7100> boot
Unknown command 'boot' - try 'help'
ar7100>
U-Boot 1.1.4 (Sep 15 2009 - 09:41:38)
AP83 (ar9100) U-boot 0.0.11
DRAM:
sri
32 MB
id read 0x100000ff
flash size 8MB, sector count = 128
Flash: 8 MB
Using default environment
In: serial
Out: serial
Err: serial
Net: ag7100_enet_initialize...
No valid address in Flash. Using fixed address
: cfg1 0xf cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
eth0 up
eth0
Autobooting in 1 seconds## Booting image at bf020000 ...
Uncompressing Kernel Image ... OK
Starting kernel ...
OpenWrt kernel loader for AR7XXX/AR9XXX
Copyright (C) 2011 Gabor Juhos juhosg@openwrt.org
Looking for OpenWrt image... found at 0xbf022000
Decompressing kernel... done!
Starting kernel at 80060000...
[ 0.000000] Linux version 4.14.121 (user@debian-c2q-x64) (gcc version 7.4.0 (OpenWrt GCC 7.4.0 r10016-c4e3fde486)) #0 Wed May 29 15:57:35 2019
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
[ 0.000000] SoC: Atheros AR9132 rev 2
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000001ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000001ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000001ffffff]
[ 0.000000] random: get_random_bytes called from start_kernel+0x90/0x478 with crng_init=0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 8128
[ 0.000000] Kernel command line: board=TL-WR1043ND console=ttyS0,115200 rootfstype=squashfs noinitrd
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 26968K/32768K available (3624K kernel code, 183K rwdata, 780K rodata, 268K init, 204K bss, 5800K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 51
[ 0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:40.000MHz
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns
[ 0.000012] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns
[ 0.007897] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[ 0.094149] pid_max: default: 32768 minimum: 301
[ 0.099047] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.105646] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.115534] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.125398] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.132088] NET: Registered protocol family 16
[ 0.138233] MIPS: machine is TP-LINK TL-WR1043ND
[ 0.447883] clocksource: Switched to clocksource MIPS
[ 0.454205] NET: Registered protocol family 2
[ 0.459651] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.466626] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.473035] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.479586] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.485430] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.492032] NET: Registered protocol family 1
[ 0.501752] Crashlog allocated RAM at address 0x1f00000
[ 0.508521] workingset: timestamp_bits=30 max_order=13 bucket_order=0
[ 0.521817] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.527635] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.547670] io scheduler noop registered
[ 0.551655] io scheduler deadline registered (default)
[ 0.557105] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.563951] console [ttyS0] disabled
[ 0.587552] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 12500000) is a 16550A
[ 0.596253] console [ttyS0] enabled
[ 0.596253] console [ttyS0] enabled
[ 0.603273] bootconsole [early0] disabled
[ 0.603273] bootconsole [early0] disabled
[ 0.616004] m25p80 spi0.0: found m25p64, expected m25p80
[ 0.621446] m25p80 spi0.0: m25p64 (8192 Kbytes)
[ 0.626982] 5 tp-link partitions found on MTD device spi0.0
[ 0.632642] Creating 5 MTD partitions on "spi0.0":
[ 0.637470] 0x000000000000-0x000000020000 : "u-boot"
[ 0.644147] 0x000000020000-0x00000019cba0 : "kernel"
[ 0.651592] 0x00000019cba0-0x0000007f0000 : "rootfs"
[ 0.657577] mtd: device 2 (rootfs) set to be root filesystem
[ 0.663387] 1 squashfs-split partitions found on MTD device rootfs
[ 0.669632] 0x000000450000-0x0000007f0000 : "rootfs_data"
[ 0.677631] 0x0000007f0000-0x000000800000 : "art"
[ 0.684156] 0x000000020000-0x0000007f0000 : "firmware"
[ 0.692270] Realtek RTL8366RB ethernet switch driver version 0.2.4
[ 0.817901] rtl8366rb rtl8366rb: using GPIO pins 18 (SDA) and 19 (SCK)
[ 0.824646] rtl8366rb rtl8366rb: RTL5937 ver. 3 chip found
[ 1.064755] libphy: rtl8366rb: probed
[ 1.069321] libphy: Fixed MDIO Bus: probed
[ 1.409749] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
[ 1.418208] NET: Registered protocol family 10
[ 1.427582] Segment Routing with IPv6
[ 1.431468] NET: Registered protocol family 17
[ 1.436643] 8021q: 802.1Q VLAN Support v1.8
[ 1.446734] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 1.455546] Freeing unused kernel memory: 268K
[ 1.460055] This architecture does not have kernel memory protection.
[ 2.557895] random: fast init done
awk: /proc/cpuinfo: No such file or directory
grep: /proc/net/dev: No such file or directory
grep: /proc/net/dev: No such file or directory
grep: /proc/cmdline: No such file or directory
grep: /proc/net/dev: No such file or directory
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
/etc/preinit: line 0: can't open '/dev/null': No such file or directory
[ 130.887960] random: crng init done
The text was updated successfully, but these errors were encountered:
mgondium:
Current trunk (reboot-10086-g62940df3a9) bricks TPLINK 1043ND v1, two devices.
U-Boot 1.1.4 (Sep 15 2009 - 09:41:38)
AP83 (ar9100) U-boot 0.0.11
DRAM:
sri
32 MB
id read 0x100000ff
flash size 8MB, sector count = 128
Flash: 8 MB
Using default environment
In: serial
Out: serial
Err: serial
Net: ag7100_enet_initialize...
No valid address in Flash. Using fixed address
: cfg1 0xf cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
eth0 up
eth0
Autobooting in 1 secondsar7100>
ar7100> boot
Unknown command 'boot' - try 'help'
ar7100>
U-Boot 1.1.4 (Sep 15 2009 - 09:41:38)
AP83 (ar9100) U-boot 0.0.11
DRAM:
sri
32 MB
id read 0x100000ff
flash size 8MB, sector count = 128
Flash: 8 MB
Using default environment
In: serial
Out: serial
Err: serial
Net: ag7100_enet_initialize...
No valid address in Flash. Using fixed address
: cfg1 0xf cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
eth0 up
eth0
Autobooting in 1 seconds## Booting image at bf020000 ...
Uncompressing Kernel Image ... OK
Starting kernel ...
OpenWrt kernel loader for AR7XXX/AR9XXX
Copyright (C) 2011 Gabor Juhos juhosg@openwrt.org
Looking for OpenWrt image... found at 0xbf022000
Decompressing kernel... done!
Starting kernel at 80060000...
[ 0.000000] Linux version 4.14.121 (user@debian-c2q-x64) (gcc version 7.4.0 (OpenWrt GCC 7.4.0 r10016-c4e3fde486)) #0 Wed May 29 15:57:35 2019
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
[ 0.000000] SoC: Atheros AR9132 rev 2
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000001ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000001ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000001ffffff]
[ 0.000000] random: get_random_bytes called from start_kernel+0x90/0x478 with crng_init=0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 8128
[ 0.000000] Kernel command line: board=TL-WR1043ND console=ttyS0,115200 rootfstype=squashfs noinitrd
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 26968K/32768K available (3624K kernel code, 183K rwdata, 780K rodata, 268K init, 204K bss, 5800K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 51
[ 0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:40.000MHz
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns
[ 0.000012] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns
[ 0.007897] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[ 0.094149] pid_max: default: 32768 minimum: 301
[ 0.099047] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.105646] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.115534] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.125398] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.132088] NET: Registered protocol family 16
[ 0.138233] MIPS: machine is TP-LINK TL-WR1043ND
[ 0.447883] clocksource: Switched to clocksource MIPS
[ 0.454205] NET: Registered protocol family 2
[ 0.459651] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.466626] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.473035] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.479586] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.485430] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.492032] NET: Registered protocol family 1
[ 0.501752] Crashlog allocated RAM at address 0x1f00000
[ 0.508521] workingset: timestamp_bits=30 max_order=13 bucket_order=0
[ 0.521817] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.527635] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.547670] io scheduler noop registered
[ 0.551655] io scheduler deadline registered (default)
[ 0.557105] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.563951] console [ttyS0] disabled
[ 0.587552] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 12500000) is a 16550A
[ 0.596253] console [ttyS0] enabled
[ 0.596253] console [ttyS0] enabled
[ 0.603273] bootconsole [early0] disabled
[ 0.603273] bootconsole [early0] disabled
[ 0.616004] m25p80 spi0.0: found m25p64, expected m25p80
[ 0.621446] m25p80 spi0.0: m25p64 (8192 Kbytes)
[ 0.626982] 5 tp-link partitions found on MTD device spi0.0
[ 0.632642] Creating 5 MTD partitions on "spi0.0":
[ 0.637470] 0x000000000000-0x000000020000 : "u-boot"
[ 0.644147] 0x000000020000-0x00000019cba0 : "kernel"
[ 0.651592] 0x00000019cba0-0x0000007f0000 : "rootfs"
[ 0.657577] mtd: device 2 (rootfs) set to be root filesystem
[ 0.663387] 1 squashfs-split partitions found on MTD device rootfs
[ 0.669632] 0x000000450000-0x0000007f0000 : "rootfs_data"
[ 0.677631] 0x0000007f0000-0x000000800000 : "art"
[ 0.684156] 0x000000020000-0x0000007f0000 : "firmware"
[ 0.692270] Realtek RTL8366RB ethernet switch driver version 0.2.4
[ 0.817901] rtl8366rb rtl8366rb: using GPIO pins 18 (SDA) and 19 (SCK)
[ 0.824646] rtl8366rb rtl8366rb: RTL5937 ver. 3 chip found
[ 1.064755] libphy: rtl8366rb: probed
[ 1.069321] libphy: Fixed MDIO Bus: probed
[ 1.409749] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
[ 1.418208] NET: Registered protocol family 10
[ 1.427582] Segment Routing with IPv6
[ 1.431468] NET: Registered protocol family 17
[ 1.436643] 8021q: 802.1Q VLAN Support v1.8
[ 1.446734] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 1.455546] Freeing unused kernel memory: 268K
[ 1.460055] This architecture does not have kernel memory protection.
[ 2.557895] random: fast init done
awk: /proc/cpuinfo: No such file or directory
grep: /proc/net/dev: No such file or directory
grep: /proc/net/dev: No such file or directory
grep: /proc/cmdline: No such file or directory
grep: /proc/net/dev: No such file or directory
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
/etc/preinit: line 0: can't open '/dev/null': No such file or directory
[ 130.887960] random: crng init done
The text was updated successfully, but these errors were encountered: