OpenWrt/LEDE Project

  • Status Unconfirmed
  • Percent Complete
    0%
  • Task Type Bug Report
  • Category Base system
  • Assigned To No-one
  • Operating System All
  • Severity High
  • Priority Very Low
  • Reported Version All
  • Due in Version Undecided
  • Due Date Undecided
  • Votes
  • Private
Attached to Project: OpenWrt/LEDE Project
Opened by Mafketel - 06.04.2019

FS#2226 - zyxel P-2812HNU-F1 initramfs has been broken with LZMA: uncompress or overwrite error 7 since R47026

Supply the following if possible:
- Device problem occurs on

zyxel P-2812HNU-F1

- Software versions of OpenWrt/LEDE release, packages, etc.

since r47026 up to the latest trunk

- Steps to reproduce
boot with serial connection stop autoboot, load initramfs, boot from ram get error

- Reason it is important

initramfs is needed for a first install.

- Posible solution
include/configs/p2812hnufx.h
probably needs:
#define CONFIG_SYS_BOOTM_LEN 0×1000000 /* 16 MB */

like in this commit for a similar modem
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=ea12a80276c0aca680d67515e7f651e2cef3f3ee

- error logs
“recent” trunk snapshot(I threw away the last compiled version for it still gave the same error)

ROM VER: 1.0.5
CFG 06
NAND
NAND Read OK

U-Boot SPL 2013.10-openwrt5 (Nov 18 2014 - 19:54:01)
SPL: initializing NAND flash
SPL: checking U-Boot image
SPL: loading U-Boot to RAM
SPL: decompressing U-Boot with LZO
SPL: jumping to U-Boot


U-Boot 2013.10-openwrt5 (Nov 18 2014 - 19:54:01) P-2812HNU-Fx

Board: ZyXEL P-2812HNU-Fx
SoC:   Lantiq VRX288 v1.1
CPU:   500 MHz
IO:    250 MHz
BUS:   250 MHz
BOOT:  NAND
DRAM:  128 MiB
NAND:  128 MiB
In:    serial
Out:   serial
Err:   serial
Net:   ltq-eth
Hit any key to stop autoboot:  0
P-2812HNU-Fx # tftpboot openwrt-lantiq-xrx200-zyxel_p-2812hnu-f1-initramfs-kernel.bin
ltq_phy: addr 0, link 1, speed 1000, duplex 1
ltq_phy: addr 1, link 0, speed 10, duplex 0
ltq_phy: addr 17, link 0, speed 10, duplex 0
ltq_phy: addr 19, link 0, speed 10, duplex 0
ltq_phy: addr 5, link 0, speed 10, duplex 0
Using ltq-eth device
TFTP from server 192.168.1.2; our IP address is 192.168.1.1
Filename 'openwrt-lantiq-xrx200-zyxel_p-2812hnu-f1-initramfs-kernel.bin'.
Load address: 0x81000000
Loading: #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         ######################################
done
Bytes transferred = 6183929 (5e5bf9 hex)
P-2812HNU-Fx # bootm $fileaddr
## Booting kernel from Legacy Image at 81000000 ...
   Image Name:   MIPS OpenWrt Linux-4.14.103
   Created:      2019-02-27  11:12:48 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    6183865 Bytes = 5.9 MiB
   Load Address: 80002000
   Entry Point:  80002000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... LZMA: uncompress or overwrite error 7 - must RESET b
ROM VER: 1.0.5
CFG 06
NAND
NAND Read OK

U-Boot SPL 2013.10-openwrt5 (Nov 18 2014 - 19:54:01)

last known working version

ROM VER: 1.0.5
CFG 06
NAND
NAND Read OK

U-Boot SPL 2013.10-openwrt5 (Nov 18 2014 - 19:54:01)
SPL: initializing NAND flash
SPL: checking U-Boot image
SPL: loading U-Boot to RAM
SPL: decompressing U-Boot with LZO
SPL: jumping to U-Boot


U-Boot 2013.10-openwrt5 (Nov 18 2014 - 19:54:01) P-2812HNU-Fx

Board: ZyXEL P-2812HNU-Fx
SoC:   Lantiq VRX288 v1.1
CPU:   500 MHz
IO:    250 MHz
BUS:   250 MHz
BOOT:  NAND
DRAM:  128 MiB
NAND:  128 MiB
In:    serial
Out:   serial
Err:   serial
Net:   ltq-eth
Hit any key to stop autoboot:  0
P-2812HNU-Fx # tftpboot openwrt-lantiq-xrx200-P2812HNUF1-uImage-initramfs
ltq_phy: addr 0, link 0, speed 10, duplex 0
ltq_phy: addr 1, link 0, speed 10, duplex 0
ltq_phy: addr 17, link 0, speed 10, duplex 0
ltq_phy: addr 19, link 0, speed 10, duplex 0
ltq_phy: addr 5, link 0, speed 10, duplex 0
Using ltq-eth device
TFTP from server 192.168.1.2; our IP address is 192.168.1.1
Filename 'openwrt-lantiq-xrx200-P2812HNUF1-uImage-initramfs'.
Load address: 0x81000000
Loading: T T T T T T T T T T
Retry count exceeded; starting again
ltq_phy: addr 0, link 1, speed 1000, duplex 1
ltq_phy: addr 1, link 0, speed 10, duplex 0
ltq_phy: addr 17, link 0, speed 10, duplex 0
ltq_phy: addr 19, link 0, speed 10, duplex 0
ltq_phy: addr 5, link 0, speed 10, duplex 0
Using ltq-eth device
TFTP from server 192.168.1.2; our IP address is 192.168.1.1
Filename 'openwrt-lantiq-xrx200-P2812HNUF1-uImage-initramfs'.
Load address: 0x81000000
Loading: #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         ##########
         1.6 MiB/s
done
Bytes transferred = 4707233 (47d3a1 hex)
P-2812HNU-Fx # bootm $fileaddr
## Booting kernel from Legacy Image at 81000000 ...
   Image Name:   MIPS OpenWrt Linux-3.18.11
   Created:      2015-04-25   1:54:58 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    4707169 Bytes = 4.5 MiB
   Load Address: 80002000
   Entry Point:  80002000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK

Starting kernel ...

[    0.000000] Linux version 3.18.11 (sylwek@WRT) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r44945) ) #2 Sat Apr 25 03:54:35 CEST 2015
[    0.000000] SoC: VR9 rev 1.1
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019555 (MIPS 34Kc)
[    0.000000] MIPS: machine is P2812HNUF1 - ZyXEL P-2812HNU-F1
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x07ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x07ffffff]
[    0.000000] Initmem setup node 0 [mem 0x00000000-0x07ffffff]
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=00021000
[    0.000000] Readback ErrCtl register=00021000
[    0.000000] Memory: 121772K/131072K available (3506K kernel code, 149K rwdata, 1036K rodata, 3160K init, 206K bss, 9300K reserved)
[    0.000000] NR_IRQS:256
[    0.000000] CPU Clock: 500MHz
[    0.000000] Calibrating delay loop... 332.54 BogoMIPS (lpj=665088)
[    0.032000] pid_max: default: 32768 minimum: 301
[    0.036000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.040000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.044000] pinctrl core: initialized pinctrl subsystem
[    0.048000] NET: Registered protocol family 16
[    0.056000] pinctrl-xway 1e100b10.pinmux: Init done
[    0.060000] dma-xway 1e104100.dma: Init done - hw rev: 7, ports: 7, channels: 28
[    0.164000] dcdc-xrx200 1f106a00.dcdc: Core Voltage : 1016 mV
[    0.168000] PCI host bridge /fpi@10000000/pci@E105400 ranges:
[    0.172000]  MEM 0x0000000018000000..0x0000000019ffffff
[    0.176000]   IO 0x000000001ae00000..0x000000001affffff
[    0.188000] gpio-stp-xway 1e100bb0.stp: Init done
[    0.192000] usbcore: registered new interface driver usbfs
[    0.196000] usbcore: registered new interface driver hub
[    0.200000] usbcore: registered new device driver usb
[    0.204000] PCI host bridge to bus 0000:00
[    0.208000] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff]
[    0.212000] pci_bus 0000:00: root bus resource [io  0xffffffff]
[    0.216000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.220000] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff]
[    0.224000] Switched to clocksource MIPS
[    0.228000] NET: Registered protocol family 2
[    0.232000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.240000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.248000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.252000] TCP: reno registered
[    0.256000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.260000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.268000] NET: Registered protocol family 1
[    5.124000] gptu: totally 6 16-bit timers/counters
[    5.132000] gptu: misc_register on minor 63
[    5.136000] gptu: succeeded to request irq 126
[    5.140000] gptu: succeeded to request irq 127
[    5.144000] gptu: succeeded to request irq 128
[    5.148000] gptu: succeeded to request irq 129
[    5.152000] gptu: succeeded to request irq 130
[    5.156000] gptu: succeeded to request irq 131
[    5.164000] ralink,eeprom ralink_eep: using RT3062.eeprom as eeprom
[    5.168000] phy-xrx200 gphy-xrx200: requesting lantiq/vr9_phy11g_a1x.bin
[    5.176000] phy-xrx200 gphy-xrx200: booting GPHY0 firmware at 6A60000
[    5.184000] phy-xrx200 gphy-xrx200: booting GPHY1 firmware at 6A60000
[    5.288000] futex hash table entries: 256 (order: -1, 3072 bytes)
[    5.296000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    5.304000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    5.312000] msgmni has been set to 237
[    5.316000] io scheduler noop registered
[    5.320000] io scheduler deadline registered (default)
[    5.328000] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112, base_baud = 0) is a lantiq,asc
[    5.336000] console [ttyLTQ0] enabled
[    5.336000] console [ttyLTQ0] enabled
[    5.344000] bootconsole [early0] disabled
[    5.344000] bootconsole [early0] disabled
[    5.352000] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xf1
[    5.352000] nand: Samsung NAND 128MiB 3,3V 8-bit
[    5.352000] nand: 128MiB, SLC, page size: 2048, OOB size: 64
[    5.368000] Scanning device for bad blocks
[    5.424000] Bad eraseblock 591 at 0x0000049e0000
[    5.428000] Bad eraseblock 616 at 0x000004d00000
[    5.464000] 4 ofpart partitions found on MTD device 10000000.nand-parts
[    5.468000] Creating 4 MTD partitions on "10000000.nand-parts":
[    5.476000] 0x000000000000-0x000000040000 : "uboot"
[    5.480000] 0x000000040000-0x000000060000 : "uboot-env"
[    5.488000] 0x000000060000-0x000000260000 : "kernel"
[    5.492000] 0x000000260000-0x000008000000 : "ubi"
[    5.600000] libphy: lantiq,xrx200-mdio: probed
[    5.620000] net-xrx200: invalid MAC, using random
[    5.688000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.3] (phy_addr=0:00, irq=-1)
[    5.756000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.3] (phy_addr=0:01, irq=-1)
[    5.824000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:11, irq=-1)
[    5.892000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:13, irq=-1)
[    5.960000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.3] (phy_addr=0:05, irq=-1)
[    5.968000] wdt 1f8803f0.watchdog: Init done
[    5.972000] TCP: cubic registered
[    5.976000] NET: Registered protocol family 17
[    5.980000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    5.992000] Bridge firewalling registered
[    5.996000] 8021q: 802.1Q VLAN Support v1.8
[    6.004000] UBI error: ubi_auto_attach: no valid UBI magic found [    6.016000] Freeing unused kernel memory: 3160K (8049a000 - 807b0000)
[    6.036000] init: failed to symlink /tmp -> /var
[    6.040000] init: Console is alive
[    6.048000] init: - watchdog -
[    6.076000] dwc2 1e101000.ifxhcd: requested GPIO 489
[    6.936000] dwc2 1e101000.ifxhcd: DWC OTG Controller
[    6.936000] dwc2 1e101000.ifxhcd: new USB bus registered, assigned bus number 1
[    6.944000] dwc2 1e101000.ifxhcd: irq 62, io mem 0x00000000
[    6.952000] dwc2 1e101000.ifxhcd: Hardware does not support descriptor DMA mode -
[    6.952000] dwc2 1e101000.ifxhcd: falling back to buffer DMA mode.
[    6.964000] hub 1-0:1.0: USB hub found
[    6.968000] hub 1-0:1.0: 1 port detected
[    7.832000] dwc2 1e106000.ifxhcd: DWC OTG Controller
[    7.832000] dwc2 1e106000.ifxhcd: new USB bus registered, assigned bus number 2
[    7.840000] dwc2 1e106000.ifxhcd: irq 91, io mem 0x00000000
[    7.848000] dwc2 1e106000.ifxhcd: Hardware does not support descriptor DMA mode -
[    7.848000] dwc2 1e106000.ifxhcd: falling back to buffer DMA mode.
[    7.860000] hub 2-0:1.0: USB hub found
[    7.864000] hub 2-0:1.0: 1 port detected
[    8.048000] init: - preinit -
[    8.160000] random: procd urandom read with 31 bits of entropy available
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    9.688000] eth0: port 0 got link
[   11.280000] procd: - early -
[   11.280000] procd: - watchdog -
[   11.852000] procd: - ubus -
[   12.864000] procd: - init -
Please press Enter to activate this console.
[   13.884000] IFXOS, Version 1.5.14 (c) Copyright 2009, Lantiq Deutschland GmbH

[   13.908000] NET: Registered protocol family 10
[   13.916000] NET: Registered protocol family 8
[   13.920000] NET: Registered protocol family 20
[   13.932000] PPP generic driver version 2.4.2
[   13.940000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   13.964000] MEI CPE Driver, Version 1.2.0

[   13.964000] (c) Copyright 2009, Infineon Technologies AG
### MEI CPE - MEI CPE - MEI CPE - MEI CPE ###


Lantiq CPE API Driver version: DSL CPE API V4.11.4
[   13.988000]
[   13.988000] Predefined debug level: 2
[   14.000000] Loading modules backported from Linux version master-2015-03-09-0-g141f155
[   14.004000] Backport generated by backports.git backports-20150129-0-gdd4a670
[   14.016000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   14.028000] Infineon Technologies DEU driver version 2.0.0
[   14.032000] IFX DEU DES initialized (multiblock).
[   14.036000] IFX DEU AES initialized (multiblock).
[   14.040000] IFX DEU ARC4 initialized (multiblock).
[   14.044000] IFX DEU SHA1 initialized.
[   14.048000] IFX DEU MD5 initialized.
[   14.052000] IFX DEU SHA1_HMAC initialized.
[   14.056000] IFX DEU MD5_HMAC initialized.
[   14.068000] nf_conntrack version 0.5.0 (1952 buckets, 7808 max)
[   14.092000] NET: Registered protocol family 24
[   14.116000] xt_time: kernel timezone is -0000
[   14.140000] cfg80211: Calling CRDA to update world regulatory domain
[   14.164000] cfg80211: World regulatory domain updated:
[   14.168000] cfg80211:  DFS Master region: unset
[   14.172000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   14.180000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   14.188000] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   14.196000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[   14.204000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[   14.212000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[   14.220000] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[   14.232000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[   14.240000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[   14.328000] PCI: Enabling device 0000:00:0e.0 (0000 -> 0002)
[   14.332000] rt2800pci 0000:00:0e.0: failed to load eeprom property
[   14.336000] ieee80211 phy0: rt2x00lib_request_eeprom_file: Info - Loading EEPROM data from 'RT3062.eeprom'.
[   14.348000] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 3572, rev 0223 detected
[   14.356000] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 0008 detected
ioctl ATM_SETESI: No such device
[   20.824000] PTM 1.0.27    PTM (E1) firmware version 0.30
[   20.828000] ifxmips_ptm: PTM init succeed
[   22.760000] device eth0.1 entered promiscuous mode
[   22.764000] device eth0 entered promiscuous mode
[   22.776000] br-lan: port 1(eth0.1) entered forwarding state
[   22.780000] br-lan: port 1(eth0.1) entered forwarding state
[   24.784000] br-lan: port 1(eth0.1) entered forwarding state
[   31.808000] random: nonblocking pool is initialized



BusyBox v1.23.2 (2015-04-25 03:40:56 CEST) built-in shell (ash)

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 -----------------------------------------------------
 CHAOS CALMER (Bleeding Edge, r45578)
 -----------------------------------------------------
  * 1 1/2 oz Gin            Shake with a glassful
  * 1/4 oz Triple Sec       of broken ice and pour
  * 3/4 oz Lime Juice       unstrained into a goblet.
  * 1 1/2 oz Orange Juice
  * 1 tsp. Grenadine Syrup
 -----------------------------------------------------
root@OpenWrt:/#

Loading...

Available keyboard shortcuts

Tasklist

Task Details

Task Editing