New issue
Have a question about this project? Sign up for a free GitHub account to open an issue and contact its maintainers and the community.
By clicking “Sign up for GitHub”, you agree to our terms of service and privacy statement. We’ll occasionally send you account related emails.
Already on GitHub? Sign in to your account
FS#2139 - broadcom-wl don't work on rt-n16 #8408
Comments
ooVizieRoo: I have the same issue. |
RAX7: I have same issue. Looks like I found the reason for this behavior. The //nas// process die after few seconds after it start. I reproduce this bug on 19.07 but it have same issue on any version higher than 17.01.7. |
DisloyalSnow911: I have the same problem. If you find a solution, write how you did it. |
oferreiro: Same problem here with my netgear wrn3500l v1. With openwrt, nas command is running with duplicate parameters: And wl0-1 is created even if I use only one wifi interface. with lede 17.01.7 works well. I tried find changes on /lib/wifi/broadcom.sh, but it is basically the same file:
diff broadcom-17.01.7.sh broadcom-19.07.02.sh
472c472
< set wireless.default_wl${i}.ssid=Lede${i#0}
---
> set wireless.default_wl${i}.ssid=OpenWrt${i#0}
When I tried RAX7 suggestion, running nas manually: I can connect my notebook but wifi speed is not good. And after some time it disconnect. |
oferreiro: Hi guys.
config wifi-device 'wl0'
option type 'broadcom'
option channel '1'
option txantenna '3'
option rxantenna '3'
option country 'BR'
option frameburst '1'
option htmode 'HT40'
option txpower '14'
option hwmode '11g'
After that, nas is started with correct params: Luci interface don't show informations. But wifi works well. And the speed is similar if I use lede 17.01.7. |
This is still a problem as of 21.02.3. |
Afo:
wifi on lede 17.01.6, with the same config, works great
install openwrt 18.06
opkg remove kmod-b43 kmod-b43legacy kmod-mac80211 kmod-cfg80211 kmod-brcmsmac
opkg install kmod-brcm-wl nas wlc wl
wl -i wl0 chanspec -c 9 -b 2 -w 40 -s -1
config wifi-device 'wl0'
option type 'broadcom'
option channel '9'
option hwmode '11ng'
option htmode 'HT40'
option txpower '16'
option txantenna '3'
option rxantenna '3'
config wifi-iface
option device 'wl0'
option network 'lan'
option mode 'ap'
option ssid 'point'
option encryption 'psk2'
option key 'pass'
option wmm '1'
option disabled '0'
After, my laptop (windows) does not connect and the phone on the android
connects for 15-20 minutes, disconnects, manually connects from the third fourth attempt
and disconnects again after a while
ifconfig shows that the interface wl0-1 is automatically created with non-existent mac address E2:CB:4E:C0:18:14 (wl0 E0:CB:4E:C0:18:13)
Wi-Fi scanner shows two access points with the same name, channels, but different MAC addresses (E2:CB:4E:C0:18:14, E0:CB:4E:C0:18:13)
I compiled two firmware with
CONFIG_TARGET_brcm47xx=y
CONFIG_TARGET_brcm47xx_mips74k=y
CONFIG_TARGET_brcm47xx_mips74k_DEVICE_asus-rt-n16=y
and
CONFIG_TARGET_brcm47xx=y
CONFIG_TARGET_brcm47xx_mips74k=y
CONFIG_TARGET_brcm47xx_mips74k_Broadcom-mips74k-wl=y
but it did not help
The text was updated successfully, but these errors were encountered: