OpenWrt/LEDE Project

  • Status Unconfirmed
  • Percent Complete
    0%
  • Task Type Bug Report
  • Category Base system
  • Assigned To No-one
  • Operating System All
  • Severity Critical
  • Priority Very Low
  • Reported Version openwrt-18.06
  • Due in Version Undecided
  • Due Date Undecided
  • Votes
  • Private
Attached to Project: OpenWrt/LEDE Project
Opened by Mihai - 10.12.2018

FS#1995 - Huawei HG655b stuck in bootloop

The router reboots continuously while booting into OpenWrt 18.06.1. The same thing happens on version 18.06.0 as well.
Last working one is LEDE 17.01.6 .

Boot log:

CFE version 1.0.37-102.6 for BCM96368 (32bit,SP,BE)
Build Date: Fri Apr 16 15:18:13 CST 2010 (lihua@IBM_x3500)
Copyright (C) 2000-2008 Broadcom Corporation.

Parallel flash device: name AM29LV320MB, id 0x2200, size 8192KB
CPU type 0x2A031: 400MHz, Bus: 160MHz, Ref: 64MHz
CPU running TP0
Total memory: 67108864 bytes (64MB)
Boot Address 0xb8000000


Board IP address                  : 192.168.1.1:ffffff00
Host IP address                   : 192.168.1.100
Gateway IP address                :
Run from flash/host (f/h)         : f
Default host run file name        : vmlinux
Default host flash file name      : bcm963xx_fs_kernel
Boot delay (0-9 seconds)          : 1
Boot image (0=latest, 1=previous) : 0
Board Id (0-6)                    : HW65x
Number of MAC Addresses (1-32)    : 11
Base MAC Address                  : 02:10:18:01:00:01
PSI Size (1-64) KBytes            : 64
Main Thread Number [0|1]          : 0

*** Press any key to stop auto run (2 seconds) ***
Auto run second count down: 0
LZMA: Prossible old LZMA format, trying to decompress..
Decompression OK!
Entry at 0x80a00000
Closing network.
Disabling Switch ports.
Flushing Receive Buffers...
0 buffers found.
Closing DMA Channels.
Starting program at 0x80a00000
[    0.000000] Linux version 4.9.120 (buildbot@builds-03.infra.lede-project.org) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r7102-3f3a2c9) ) #0 SMP Wed Aug 15 20:42:39 2018
[    0.000000] Detected Broadcom 0x6368 CPU revision b2
[    0.000000] CPU frequency is 400 MHz
[    0.000000] 64MB of RAM installed
[    0.000000] board_bcm963xx: Boot address 0xb8000000
[    0.000000] board_bcm963xx: CFE version: 1.0.37-102.6
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 0002a031 (Broadcom BMIPS4350)
[    0.000000] board: board name: HW65x
[    0.000000] MIPS: machine is Huawei HG655b
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
[    0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] percpu: Embedded 12 pages/cpu @8108a000 s17440 r8192 d23520 u49152
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line: rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Memory: 58636K/65536K available (3773K kernel code, 183K rwdata, 588K rodata, 1336K init, 227K bss, 6900K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=16, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:256
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns
[    0.000015] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns
[    0.008130] Calibrating delay loop... 397.82 BogoMIPS (lpj=795648)
[    0.042781] pid_max: default: 32768 minimum: 301
[    0.047767] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.054541] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.069410] SMP: Booting CPU1...
[   11.992235] Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
[   11.992251] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[   11.992575] CPU1 revision is: 0002a031 (Broadcom BMIPS4350)
[    0.121564] Synchronize counters for CPU 1:
[    0.121565] done.
[    0.121573] SMP: CPU1 is running
[    0.131460] Brought up 2 CPUs
[    0.142908] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.152949] futex hash table entries: 512 (order: 1, 8192 bytes)
[    0.159260] pinctrl core: initialized pinctrl subsystem
[    0.166652] NET: Registered protocol family 16
[    0.175484] Can't analyze schedule() prologue at 803baf08
[    0.197227] registering PCI controller with io_map_base unset
[    0.203139] registering PCI controller with io_map_base unset
[    0.234630] PCI host bridge to bus 0000:00
[    0.238879] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
[    0.245938] pci_bus 0000:00: root bus resource [io  0x8000000-0x8007fff]
[    0.252837] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    0.259812] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.276363] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x3000ffff]
[    0.284076] PCI host bridge to bus 0000:01
[    0.288281] pci_bus 0000:01: root bus resource [mem 0x38000000-0x3fffffff]
[    0.295332] pci_bus 0000:01: root bus resource [io  0x8008000-0x800ffff]
[    0.302249] pci_bus 0000:01: root bus resource [??? 0x00000000 flags 0x0]
[    0.309225] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff]
[    0.317823] pci 0000:01:1e.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    0.326326] pci 0000:01:1e.0: BAR 10: assigned [mem 0x38000000-0x3fffffff]
[    0.333401] pci 0000:01:1e.0: BAR 7: assigned [io  0x8008000-0x80080ff]
[    0.340186] pci 0000:01:1e.0: BAR 8: assigned [io  0x8008400-0x80084ff]
[    0.346986] pci 0000:01:1e.0: CardBus bridge to [bus 02-05]
[    0.352727] pci 0000:01:1e.0:   bridge window [io  0x8008000-0x80080ff]
[    0.359528] pci 0000:01:1e.0:   bridge window [io  0x8008400-0x80084ff]
[    0.366347] pci 0000:01:1e.0:   bridge window [mem 0x38000000-0x3fffffff]
[    0.380818] clocksource: Switched to clocksource MIPS
[    0.388361] NET: Registered protocol family 2
[    0.394665] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.401924] TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
[    0.408534] TCP: Hash tables configured (established 1024 bind 1024)
[    0.415436] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.421530] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.428514] NET: Registered protocol family 1
[    0.435230] Crashlog allocated RAM at address 0x3f00000
[    0.444861] random: fast init done
[    0.450589] workingset: timestamp_bits=30 max_order=14 bucket_order=0
[    0.471721] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.477733] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.512734] io scheduler noop registered
[    0.516874] io scheduler deadline registered (default)
[    0.525247] bcm6368-pinctrl 10000080.pin-controller: registered at mmio b0000080
[    0.534012] 10000100.serial: ttyS0 at MMIO 0x10000100 (irq = 10, base_baud = 1562500) is a bcm63xx_uart
[    0.543754] console [ttyS0] enabled
[    0.543754] console [ttyS0] enabled
[    0.550889] bootconsole [early0] disabled
[    0.550889] bootconsole [early0] disabled
[    0.559894] bcm63xx-rng bcm63xx-rng: registered RNG driver
[    0.566702] 18000000.nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x001000
[    0.577107] Amd/Fujitsu Extended Query Table at 0x0040
[    0.582383]   Amd/Fujitsu Extended Query version 1.3.
[    0.587560] number of CFI chips: 1
[    0.591665] bcm63xxpart: Partition 0 is CFE offset 0 and length 10000
[    0.598317] bcm63xxpart: Partition 1 is nvram offset 7f0000 and length 10000
[    0.605576] bcm63xxpart: Partition 2 is linux offset 10000 and length 7e0000
[    0.612884] 3 bcm63xxpart partitions found on MTD device 18000000.nor
[    0.619494] Creating 3 MTD partitions on "18000000.nor":
[    0.624958] 0x000000000000-0x000000010000 : "CFE"
[    0.631868] 0x0000007f0000-0x000000800000 : "nvram"
[    0.638937] 0x000000010000-0x0000007f0000 : "linux"
[    0.646345] parser_imagetag: rootfs: CFE image tag at 0x0 CRC invalid (expected 0212102b, actual 24b1b887)
[    0.657859] bcm63xx-spi 10000800.spi: at [mem 0x10000800-0x10000f0b flags 0x200] (irq 9, FIFOs size 542)
[    0.669448] libphy: Fixed MDIO Bus: probed
[    0.717976] b53_common: found switch: BCM63xx, rev 0
[    0.723524] bcm63xx-wdt bcm63xx-wdt:  started, timer margin: 30 sec
[    0.733982] NET: Registered protocol family 10
[    0.741672] NET: Registered protocol family 17
[    0.746347] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    0.759683] 8021q: 802.1Q VLAN Support v1.8
[    0.774484] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6
[    0.782230] Please append a correct "root=" boot option; here are the available partitions:
[    0.790832] 1f00              64 mtdblock0 [    0.794921]  (driver?)
[    0.797342] 1f01              64 mtdblock1 [    0.801455]  (driver?)
[    0.803858] 1f02            8064 mtdblock2 [    0.807994]  (driver?)
[    0.810425] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[    0.820791] Rebooting in 1 seconds..
[    1.819072] triggering watchdog soft-reset...


Mihai commented on 11.12.2018 19:48

Oh, that's great news! Thank you very much for looking into this!

Loading...

Available keyboard shortcuts

Tasklist

Task Details

Task Editing