Skip to content
New issue

Have a question about this project? Sign up for a free GitHub account to open an issue and contact its maintainers and the community.

By clicking “Sign up for GitHub”, you agree to our terms of service and privacy statement. We’ll occasionally send you account related emails.

Already on GitHub? Sign in to your account

FS#181 - Changing TX power doesn't nothing (MediaTek MT7628AN ver:1 eco:2) #5237

Open
openwrt-bot opened this issue Sep 17, 2016 · 0 comments
Labels

Comments

@openwrt-bot
Copy link

Cjcr:

Hello,

As I said, if I change the TX power from 0 dBm to 20 dBm doesn't nothing. There isn't any visible change in tx power. I tested other powers too (5, 8, 15,..).

It is a Xiaomi Nano (lite).

SoC Type: MediaTek MT7628AN ver:1 eco:2
MIPS: machine is MiWiFi Nano
Linux version 4.4.19 (-) (gcc version 5.4.0 (LEDE GCC 5.4.0 r1444) ) #0 Fri Aug 26 15:03:40 2016.

@openwrt-bot
Copy link
Author

sanitariu:

This does not work also on tp-link 840 version 4.
It is MediaTek MT7628AN.
Actually txpower is always 0

@openwrt-bot
Copy link
Author

dsouza:

I can confirm this issue also with the 5Ghz radio on a TP-Link Archer C6 3.2 with both AN and AC network (MT7621 + MT7603EN 2.4Ghz + MT7613BEN 5Ghz) running a snapshot build (r17525-a46fa5c3a7):

Linux ap2 5.4.145 #0 SMP Thu Sep 16 05:59:50 2021 mips GNU/Linux

The issue seems to be with the M76 driver which is completely ignoring the "TX Power" set via LuCI and UCI. I am saying the issue seems to be the Wi-Fi driver because UCI and iwinfo everything seems to be OK.

See the example below. I've set the TX Power to 0dbm for testing purposes, and UCI and iwinfo correctly show the value I've configured:

root@ap2:~# uci show wireless.radio1
wireless.radio1=wifi-device
wireless.radio1.type='mac80211'
wireless.radio1.path='1e140000.pcie/pci0000:00/0000:00:01.0/0000:02:00.0'
wireless.radio1.band='5g'
wireless.radio1.htmode='VHT80'
wireless.radio1.country='PA'
wireless.radio1.channel='100'
wireless.radio1.cell_density='0'
wireless.radio1.txpower='0'

root@ap2:# iwinfo wlan1 info
wlan1 ESSID: "dshome5ghz-tst"
Access Point: xx:xx:xx:xx:C8:40
Mode: Master Channel: 100 (5.500 GHz)
Center Channel 1: 106 2: unknown
Tx-Power: 0 dBm Link Quality: 24/70
Signal: -86 dBm Noise: -92 dBm
Bit Rate: 234.0 MBit/s
Encryption: WPA2 PSK (CCMP)
Type: nl80211 HW Mode(s): 802.11nac
Hardware: 14C3:7663 14C3:7663 [MediaTek MT7613BE]
TX power offset: none
Frequency offset: none
Supports VAPs: yes PHY name: phy1
root@ap2:
#

However the 0dBm configuration above has no effect on TX Power at all.

With TX Power configured at 0 dBm for the 5Ghz radio in the example above, Wi-Fi signal should be very weak and should work only on the same room and close to the access point.

However as seen below the signal strength measured with a laptop located about 10 meters away from the access point with a brick wall between the laptop and the access point and the wi-if signal strength is still strong. This is the same level as if TX Power is at 22dBm (driver default level), so in fact the TX Power configuration is not working:

ubuntu@ubuntu:~$ iwconfig wlp2s0
wlp2s0 IEEE 802.11 ESSID:"dshome5ghz-tst"
Mode:Managed Frequency:5.5 GHz Access Point: xx:xx:xx:xx:C8:40
Bit Rate=26 Mb/s Tx-Power=22 dBm
Retry short limit:7 RTS thr:off Fragment thr:off
Power Management:on
Link Quality=42/70 Signal level=-68 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:30 Missed beacon:0

I've experimented other TX Power levels, and none configuration has any effect on OpenWRT TX Power. I am not sure if this is an OpenWRT bug or if it is in fact a MT76 driver issue to be reported upstream by OpenWRT devs.

Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment
Labels
Projects
None yet
Development

No branches or pull requests

1 participant