OpenWrt/LEDE Project

  • Status Unconfirmed
  • Percent Complete
    0%
  • Task Type Bug Report
  • Category Base system
  • Assigned To No-one
  • Operating System All
  • Severity Critical
  • Priority Very Low
  • Reported Version Trunk
  • Due in Version Undecided
  • Due Date Undecided
  • Private
Attached to Project: OpenWrt/LEDE Project
Opened by agriveaux - 28.07.2018

FS#1701 - [wnr3500l-v1-other-regions] Unable to upgrade from lede-17.01.4 to lede-17.01.5

Hello,

I was unable to upgrade from lede-17.01.4 to lede-17.01.5 from web interface or from bootloader tftpd with wnr3500l-v1-other-regions images, attached the boot log from both firmware and the sha256sums:


sha256sum lede-17.01.5-brcm47xx-mips74k-netgear-wnr3500l-v1-other-regions-squashfs.chk
5dbaddfae5bbbcca6fb4f0e2810de2135dbadf0bf346e755ca6063700f445d4d lede-17.01.5-brcm47xx-mips74k-netgear-wnr3500l-v1-other-regions-squashfs.chk

sha256sum lede-17.01.4-brcm47xx-mips74k-netgear-wnr3500l-v1-other-regions-squashfs.chk
6e4eaa5e988f99f77b5e00d8be4f288934ae69e3056ceaffc4e3fb60099d2a3c lede-17.01.4-brcm47xx-mips74k-netgear-wnr3500l-v1-other-regions-squashfs.chk

Start TFTP server
Reading :: Done. 3805242 bytes read
Programming...done. 3805242 bytes written
Write len/chksum offset @ 0x0074FFF8...done.
Decompressing..........done

CFE for WNR3500L version: v1.0.36
Build Date: Tue Aug 11 15:09:14 CST 2009
Init Arena
Init Devs.
Boot partition size = 262144(0×40000)
Found a 8MB ST compatible serial flash
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.10.56.28
CPU type 0×19740: 453MHz
Tot mem: 65536 KBytes

Device eth0: hwaddr C0-3F-0E-E1-97-EA, ipaddr 192.168.1.1, mask 255.255.255.0

      gateway not set, nameserver not set

too long file.
LZMA boot failed
Loader:raw Filesys:raw Dev:flash0.os File: Options:(null)
Loading: .. 3864 bytes read
Entry at 0×80001000 Closing network.
Starting program at 0×80001000 [ 0.000000] Linux version 4.4.140 (buildbot@builds-02.infra.lede-project.org) (gcc version 5.4.0 (LEDE GCC 5.4.0 r3104-41de9a2) ) #0 Fri Jul 13 19:25:14 2018
[ 0.000000] CPU0 revision is: 00019740 (MIPS 74Kc)
[ 0.000000] bcm47xx: Using bcma bus
[ 0.000000] bcma: bus0: Found chip with id 0×4716, rev 0×01 and package 0x0A
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0×0000000000000000-0x0000000003ffffff]
[ 0.000000] HighMem empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0×0000000000000000-0x0000000003ffffff]
[ 0.000000] Initmem setup node 0 [mem 0×0000000000000000-0x0000000003ffffff]
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: noinitrd console=ttyS0,115200
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 60876K/65536K available (3006K kernel code, 139K rwdata, 368K rodata, 188K init, 294K bss, 4660K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:128
[ 0.000000] bcma: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id 0×800, rev 0x1F, class 0×0)
[ 0.000000] bcma: bus0: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0×812, rev 0×11, class 0×0)
[ 0.000000] bcma: bus0: Core 2 found: GBit MAC (manuf 0x4BF, id 0x82D, rev 0×00, class 0×0)
[ 0.000000] bcma: bus0: Core 3 found: MIPS 74K (manuf 0x4A7, id 0x82C, rev 0×01, class 0×0)
[ 0.000000] bcma: bus0: Core 4 found: USB 2.0 Host (manuf 0x4BF, id 0×819, rev 0×04, class 0×0)
[ 0.000000] bcma: bus0: Core 5 found: PCIe (manuf 0x4BF, id 0×820, rev 0x0E, class 0×0)
[ 0.000000] bcma: bus0: Core 6 found: DDR1/DDR2 Memory Controller (manuf 0x4BF, id 0x82E, rev 0×01, class 0×0)
[ 0.000000] bcma: bus0: Core 7 found: Internal Memory (manuf 0x4BF, id 0x80E, rev 0×07, class 0×0)
[ 0.000000] bcma: bus0: Core 8 found: I2S (manuf 0x4BF, id 0×834, rev 0×00, class 0×0)
[ 0.000000] bcma: bus0: Found M25P64 serial flash (size: 8192KiB, blocksize: 0×10000, blocks: 128)
[ 0.000000] bcma: bus0: Early bus registered
[ 0.000000] MIPS: machine is Netgear WNR3500L
[ 0.000000] bcm47xx: Setting up vectored interrupts
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 8438235966 ns
[ 0.000016] sched_clock: 32 bits at 226MHz, resolution 4ns, wraps every 9481163773ns
[ 0.000088] Calibrating delay loop... 226.09 BogoMIPS (lpj=1130496)
[ 0.070059] pid_max: default: 32768 minimum: 301
[ 0.070323] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.070355] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.074430] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.074486] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.075763] NET: Registered protocol family 16
[ 0.076831] Can’t analyze schedule() prologue at 800077c8
[ 0.097612] clocksource: Switched to clocksource MIPS
[ 0.099778] NET: Registered protocol family 2
[ 0.101549] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.101611] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.101653] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.101827] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.101880] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.102346] NET: Registered protocol family 1
[ 0.136945] bcma: bus0: PCIEcore in host mode found
[ 0.136961] bcma: bus0: This PCIE core is disabled and not working
[ 0.138624] bcma: bus0: Bus registered
[ 0.140082] Crashlog allocated RAM at address 0x3f00000
[ 0.173818] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.173852] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) © 2001-2006 Red Hat, Inc.
[ 0.179094] io scheduler noop registered
[ 0.179132] io scheduler deadline registered (default)
[ 0.179528] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.184744] console [ttyS0] disabled
[ 0.205005] serial8250.0: ttyS0 at MMIO 0xb8000300 (irq = 2, base_baud = 1250000) is a U6_16550A
[ 0.650369] console [ttyS0] enabled
[ 0.716781] 8 bcm47xxpart partitions found on MTD device bcm47xxsflash
[ 0.723492] Creating 8 MTD partitions on “bcm47xxsflash”:
[ 0.729058] 0×000000000000-0×000000040000 : “boot” [ 0.738490] 0×000000040000-0x0000007d0000 : “firmware” [ 0.746855] 0x0000007d0000-0x0000007e0000 : “POT” [ 0.754929] 0x0000007e0000-0x0000007f0000 : “board_data” [ 0.763597] 0x0000007f0000-0×000000800000 : “nvram” [ 0.771879] 0x00000004001c-0×000000040924 : “loader” [ 0.780208] 0×000000040924-0x000000167c00 : “linux” [ 0.788492] 0x000000167c00-0x0000007d0000 : “rootfs” [ 0.796719] mtd: device 7 (rootfs) set to be root filesystem
[ 0.802656] 1 squashfs-split partitions found on MTD device rootfs
[ 0.809019] 0x0000003a0000-0x0000007d0000 : “rootfs_data” [ 0.821473] libphy: Fixed MDIO Bus: probed
[ 0.825896] bgmac_bcma bcma0:2: Found PHY addr: 30 (NOREGS)
[ 0.834901] libphy: bcma_mdio mii bus: probed
[ 0.839469] bgmac_bcma bcma0:2: Support for Roboswitch not implemented
[ 0.993379] b53_common: found switch: BCM53115, rev 8
[ 1.000032] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded
[ 1.006312] bcm47xx-wdt bcm47xx-wdt.0: BCM47xx Watchdog Timer enabled (30 seconds)
[ 1.016346] NET: Registered protocol family 10
[ 1.027256] NET: Registered protocol family 17
[ 1.032044] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 1.044946] 8021q: 802.1Q VLAN Support v1.8
[ 1.061633] VFS: Mounted root (squashfs filesystem) readonly on device 31:7.
[ 1.070250] Freeing unused kernel memory: 188K

FE for WNR3500L version: v1.0.36
Build Date: Tue Aug 11 15:09:14 CST 2009
Init Arena
Init Devs.
Boot partition size = 262144(0×40000)
Found a 8MB ST compatible serial flash
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.10.56.28
CPU type 0×19740: 453MHz
Tot mem: 65536 KBytes

Device eth0: hwaddr C0-3F-0E-E1-97-EA, ipaddr 192.168.1.1, mask 255.255.255.0

      gateway not set, nameserver not set

too long file.
LZMA boot failed
Loader:raw Filesys:raw Dev:flash0.os File: Options:(null)
Loading: .. 3848 bytes read
Entry at 0×80001000 Closing network.
Starting program at 0×80001000 [ 0.000000] Linux version 4.4.92 (buildbot@builds-02.infra.lede-project.org) (gcc version 5.4.0 (LEDE GCC 5.4.0 r3104-41de9a2) ) #0 Tue Oct 17 17:46:20 2017
[ 0.000000] CPU0 revision is: 00019740 (MIPS 74Kc)
[ 0.000000] bcm47xx: Using bcma bus
[ 0.000000] bcma: bus0: Found chip with id 0×4716, rev 0×01 and package 0x0A
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0×0000000000000000-0x0000000003ffffff]
[ 0.000000] HighMem empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0×0000000000000000-0x0000000003ffffff]
[ 0.000000] Initmem setup node 0 [mem 0×0000000000000000-0x0000000003ffffff]
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: noinitrd console=ttyS0,115200
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 60940K/65536K available (2979K kernel code, 134K rwdata, 368K rodata, 156K init, 294K bss, 4596K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:128
[ 0.000000] bcma: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id 0×800, rev 0x1F, class 0×0)
[ 0.000000] bcma: bus0: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0×812, rev 0×11, class 0×0)
[ 0.000000] bcma: bus0: Core 2 found: GBit MAC (manuf 0x4BF, id 0x82D, rev 0×00, class 0×0)
[ 0.000000] bcma: bus0: Core 3 found: MIPS 74K (manuf 0x4A7, id 0x82C, rev 0×01, class 0×0)
[ 0.000000] bcma: bus0: Core 4 found: USB 2.0 Host (manuf 0x4BF, id 0×819, rev 0×04, class 0×0)
[ 0.000000] bcma: bus0: Core 5 found: PCIe (manuf 0x4BF, id 0×820, rev 0x0E, class 0×0)
[ 0.000000] bcma: bus0: Core 6 found: DDR1/DDR2 Memory Controller (manuf 0x4BF, id 0x82E, rev 0×01, class 0×0)
[ 0.000000] bcma: bus0: Core 7 found: Internal Memory (manuf 0x4BF, id 0x80E, rev 0×07, class 0×0)
[ 0.000000] bcma: bus0: Core 8 found: I2S (manuf 0x4BF, id 0×834, rev 0×00, class 0×0)
[ 0.000000] bcma: bus0: Found M25P64 serial flash (size: 8192KiB, blocksize: 0×10000, blocks: 128)
[ 0.000000] bcma: bus0: Early bus registered
[ 0.000000] MIPS: machine is Netgear WNR3500L
[ 0.000000] bcm47xx: Setting up vectored interrupts
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 8438235966 ns
[ 0.000015] sched_clock: 32 bits at 226MHz, resolution 4ns, wraps every 9481163773ns
[ 0.000087] Calibrating delay loop... 226.09 BogoMIPS (lpj=1130496)
[ 0.070070] pid_max: default: 32768 minimum: 301
[ 0.070333] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.070363] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.074377] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.074431] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.075699] NET: Registered protocol family 16
[ 0.076766] Can’t analyze schedule() prologue at 800077c8
[ 0.097432] clocksource: Switched to clocksource MIPS
[ 0.099646] NET: Registered protocol family 2
[ 0.101436] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.101500] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.101541] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.101723] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.101772] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.102233] NET: Registered protocol family 1
[ 0.138267] bcma: bus0: PCIEcore in host mode found
[ 0.138284] bcma: bus0: This PCIE core is disabled and not working
[ 0.139823] bcma: bus0: Bus registered
[ 0.141279] Crashlog allocated RAM at address 0x3f00000
[ 0.173720] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.173754] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) © 2001-2006 Red Hat, Inc.
[ 0.178931] io scheduler noop registered
[ 0.178969] io scheduler deadline registered (default)
[ 0.179399] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.184624] console [ttyS0] disabled
[ 0.204881] serial8250.0: ttyS0 at MMIO 0xb8000300 (irq = 2, base_baud = 1250000) is a U6_16550A
[ 0.649908] console [ttyS0] enabled
[ 0.716330] 8 bcm47xxpart partitions found on MTD device bcm47xxsflash
[ 0.723042] Creating 8 MTD partitions on “bcm47xxsflash”:
[ 0.728592] 0×000000000000-0×000000040000 : “boot” [ 0.737974] 0×000000040000-0x0000007d0000 : “firmware” [ 0.746296] 0x0000007d0000-0x0000007e0000 : “POT” [ 0.754307] 0x0000007e0000-0x0000007f0000 : “board_data” [ 0.762954] 0x0000007f0000-0×000000800000 : “nvram” [ 0.771197] 0x00000004001c-0x00000004091c : “loader” [ 0.779503] 0x00000004091c-0×000000166000 : “linux” [ 0.787711] 0×000000166000-0x0000007d0000 : “rootfs” [ 0.795968] mtd: device 7 (rootfs) set to be root filesystem
[ 0.801906] 1 squashfs-split partitions found on MTD device rootfs
[ 0.808266] 0x0000003a0000-0x0000007d0000 : “rootfs_data” [ 0.821280] libphy: Fixed MDIO Bus: probed
[ 0.825701] bgmac_bcma bcma0:2: Found PHY addr: 30 (NOREGS)
[ 0.834008] libphy: bcma_mdio mii bus: probed
[ 0.838578] bgmac_bcma bcma0:2: Support for Roboswitch not implemented
[ 0.993243] b53_common: found switch: BCM53115, rev 8
[ 0.999847] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded
[ 1.006179] bcm47xx-wdt bcm47xx-wdt.0: BCM47xx Watchdog Timer enabled (30 seconds)
[ 1.016224] NET: Registered protocol family 10
[ 1.027053] NET: Registered protocol family 17
[ 1.031842] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 1.044737] 8021q: 802.1Q VLAN Support v1.8
[ 1.059021] VFS: Mounted root (squashfs filesystem) readonly on device 31:7.
[ 1.067285] Freeing unused kernel memory: 156K
[ 2.806611] init: Console is alive
[ 2.810639] init: - watchdog -
[ 3.997377] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 4.143653] usbcore: registered new interface driver usbfs
[ 4.149584] usbcore: registered new interface driver hub
[ 4.155199] usbcore: registered new device driver usb
[ 4.169708] ehci_hcd: USB 2.0 ‘Enhanced’ Host Controller (EHCI) Driver
[ 4.178819] ehci-platform: EHCI generic platform driver
[ 4.184317] ehci-platform ehci-platform.0: EHCI Host Controller
[ 4.190529] ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1
[ 4.199005] ehci-platform ehci-platform.0: irq 5, io mem 0×18004000 [ 4.217502] ehci-platform ehci-platform.0: USB 2.0 started, EHCI 1.00
[ 4.225784] hub 1-0:1.0: USB hub found
[ 4.230502] hub 1-0:1.0: 2 ports detected
[ 4.239429] ohci_hcd: USB 1.1 ‘Open’ Host Controller (OHCI) Driver
[ 4.248047] ohci-platform: OHCI generic platform driver
[ 4.253525] ohci-platform ohci-platform.0: Generic Platform OHCI controller
[ 4.260791] ohci-platform ohci-platform.0: new USB bus registered, assigned bus number 2
[ 4.269219] ohci-platform ohci-platform.0: irq 5, io mem 0×18009000 [ 4.333295] hub 2-0:1.0: USB hub found
[ 4.338046] hub 2-0:1.0: 2 ports detected
[ 4.348953] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 4.358415] init: - preinit -
[ 4.937596] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 6.107517] bgmac_bcma bcma0:2 eth0: Link is Up - 1Gbps/Full - flow control off
[ 6.115064] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 7.012167] random: procd: uninitialized urandom read (4 bytes read, 11 bits of entropy available)
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 10.209518] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
[ 10.223679] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 10.512569] procd: - early -
[ 10.515754] procd: - watchdog -
[ 11.163982] procd: - watchdog -
[ 11.168071] procd: - ubus -
[ 11.325865] random: ubusd: uninitialized urandom read (4 bytes read, 18 bits of entropy available)
[ 11.441414] random: ubusd: uninitialized urandom read (4 bytes read, 18 bits of entropy available)
[ 11.451517] random: ubusd: uninitialized urandom read (4 bytes read, 18 bits of entropy available)
[ 11.460856] random: ubusd: uninitialized urandom read (4 bytes read, 18 bits of entropy available)
[ 11.470925] random: ubusd: uninitialized urandom read (4 bytes read, 18 bits of entropy available)
[ 11.480252] random: ubusd: uninitialized urandom read (4 bytes read, 18 bits of entropy available)
[ 11.489980] random: ubusd: uninitialized urandom read (4 bytes read, 18 bits of entropy available)
[ 11.499705] random: ubusd: uninitialized urandom read (4 bytes read, 18 bits of entropy available)
[ 11.509819] procd: - init -
Please press Enter to activate this console.
[ 13.270551] kmodloader: loading kernel modules from /etc/modules.d/*
[ 13.285240] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 13.311701] Loading modules backported from Linux version wt-2017-01-31-0-ge882dff19e7f
[ 13.319947] Backport generated by backports.git backports-20160324-13-g24da7d3c
[ 13.333019] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 13.352710] nf_conntrack version 0.5.0 (954 buckets, 3816 max)
[ 13.416167] xt_time: kernel timezone is -0000
[ 13.508191] PPP generic driver version 2.4.2
[ 13.517216] NET: Registered protocol family 24
[ 13.540700] b43-phy0: Broadcom 4716 WLAN found (core revision 17)
[ 13.547966] b43-phy0: Found PHY: Analog 8, Type 4 (N), Revision 5
[ 13.554192] b43-phy0: Found Radio: Manuf 0x17F, ID 0×2056, Revision 7, Version 0
[ 13.562486] Broadcom 43xx driver loaded [ Features: NL ]
[ 13.686566] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 15.687579] random: jshn: uninitialized urandom read (4 bytes read, 25 bits of entropy available)
[ 25.746893] jffs2_scan_eraseblock(): End of filesystem marker found at 0×0 [ 25.777547] jffs2_build_filesystem(): unlocking the mtd device... done.
[ 25.784300] jffs2_build_filesystem(): erasing all blocks after the end marker...
[ 30.647563] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 30.687011] device eth0.1 entered promiscuous mode
[ 30.692016] device eth0 entered promiscuous mode
[ 30.730434] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 30.868472] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready
[ 32.267639] bgmac_bcma bcma0:2 eth0: Link is Up - 1Gbps/Full - flow control off
[ 32.275184] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 32.307649] br-lan: port 1(eth0.1) entered forwarding state
[ 32.313443] br-lan: port 1(eth0.1) entered forwarding state
[ 32.319424] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
[ 32.427588] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 34.307460] br-lan: port 1(eth0.1) entered forwarding state

agriveaux commented on 28.07.2018 12:00

Maybe related to the almost same bug  FS#1697 .
Can you correct the Reported Version ?

Loading...

Available keyboard shortcuts

Tasklist

Task Details

Task Editing