New issue
Have a question about this project? Sign up for a free GitHub account to open an issue and contact its maintainers and the community.
By clicking “Sign up for GitHub”, you agree to our terms of service and privacy statement. We’ll occasionally send you account related emails.
Already on GitHub? Sign in to your account
FS#1665 - Netgear r6100 (ar71xx) does not recognize 5Ghz wlan interface #8493
Comments
mkresin: These last four lines are the related error messages from your logs:
[ 12.716479] ath10k_pci 0000:00:00.0: pci irq legacy oper_irq_mode 1 irq_mode 0 reset_mode 0
[ 12.990606] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:00:00.0.bin failed with error -2
[ 13.001516] ath10k_pci 0000:00:00.0: Falling back to user helper
[ 13.231757] firmware ath10k!pre-cal-pci-0000:00:00.0.bin: firmware_loading_store: map pages failed
[ 13.241179] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/cal-pci-0000:00:00.0.bin failed with error -2
[ 13.251725] ath10k_pci 0000:00:00.0: Falling back to user helper
[ 13.459980] firmware ath10k!cal-pci-0000:00:00.0.bin: firmware_loading_store: map pages failed
[ 13.469153] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/firmware-6.bin failed with error -2
[ 13.480056] ath10k_pci 0000:00:00.0: Falling back to user helper
[ 13.683366] firmware ath10k!QCA988X!hw2.0!firmware-6.bin: firmware_loading_store: map pages failed
[ 13.700753] ath10k_pci 0000:00:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043222ff sub 0000:0000
[ 13.710182] ath10k_pci 0000:00:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
[ 13.724631] ath10k_pci 0000:00:00.0: firmware ver 10.2.4-1.0-00033 api 5 features no-p2p,raw-mode,mfp,allows-mesh-bcast crc32 c41417d0
[ 13.827927] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/board-2.bin failed with error -2
[ 13.838557] ath10k_pci 0000:00:00.0: Falling back to user helper
[ 13.945426] firmware ath10k!QCA988X!hw2.0!board-2.bin: firmware_loading_store: map pages failed
[ 13.981969] ath10k_pci 0000:00:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
[ 14.135854] ath10k_pci 0000:00:00.0: otp calibration failed: 2
[ 14.141814] ath10k_pci 0000:00:00.0: failed to run otp: -22
[ 14.147490] ath10k_pci 0000:00:00.0: could not init core (-22)
[ 14.153527] ath10k_pci 0000:00:00.0: could not probe fw (-22)
But no idea what is going wrong. Does it work with LEDE 17.04? |
mkresin: I might have spotted an unintended change in https://git.openwrt.org/f3bdc4a76aa2. Would you please try an image from https://www.kresin.me/files/ar71xx-nand/. |
andy-vdg: This could be related to task_id=1607 same problem but for Nighthawk X6 R8000 |
cvmiller: I tried the link suggested https://www.kresin.me/files/ar71xx-nand/ Did a sysupgrade of the R6100, still no 5Ghz. Removed /etc/config/wireless and rebooted (this rebuilds the file). Still no 5 Ghz. Here's the contents of the rebuilt file: config wifi-device 'radio0' config wifi-iface 'default_radio0' |
cvmiller:
Yes, both 2.4 and 5 Ghz radios work as expected (come up, are visable in LuCI, pass traffic) on the R6100 with v17.01.4 |
cvmiller: Any update on this issue? The 5Ghz works fine in 17.01.4, but is NOT working in any later release, including 19.07.0. |
cvmiller:
Supply the following if possible:
Problem occurs on Netgear R6100
Software version 18.06 rc2 (also on rc1)
Steps to reproduce:
Attaching dmesg and logread from boot of 18.06 rc2
The text was updated successfully, but these errors were encountered: