You signed in with another tab or window. Reload to refresh your session.You signed out in another tab or window. Reload to refresh your session.You switched accounts on another tab or window. Reload to refresh your session.Dismiss alert
device: DSL-2750B version D1 EU ([[https://openwrt.org/toh/hwdata/d-link/d-link_dsl-2750b_d1|Techdata]])
LEDE version: 17.01
(I hope I picked the right category)
I tried flashing the image from the link in the techdata page, but the device says it doesn't accept it because of a wrong id, so I connected to the serial pins to see what is the right id and this is the boot log: HELO
CPUI
L1CI
DRAM
PHYS
PHYE
DDR1
333H
SIZ3
RACE
PASS
ZBSS
CODE
DATA
L12F
MAIN
CFE version 1.0.38-114.170 for BCM96318 (32bit,SP,BE)
Build Date: Thu Mar 28 13:52:02 HKT 2013 (root@ubuntu)
Copyright (C) 2000-2011 Broadcom Corporation.
HS Serial flash device: name MX25L64, id 0xc217 size 8192KB
Total Flash size: 8192K with 2048 sectors
Flash not used for Auxillary File System
Chip ID: BCM6318B0, MIPS: 333MHz, DDR: 333MHz, Bus: 166MHz
Main Thread: TP0
Total Memory: 67108864 bytes (64MB)
Boot Address: 0xb8000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Board Id (0-6) : AW5200U
Number of MAC Addresses (1-32) : 11
Base MAC Address : 6c:19:8f:8d:b8:fc
PSI Size (1-64) KBytes : 24
Enable Backup PSI [0|1] : 0
System Log Size (0-256) KBytes : 0
Auxillary File System Size Percent: 0
Main Thread Number [0|1] : 0
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 1�1�0
udp bind success
g_secs=02
No received any packet
Packet loss:0, noncontinuative packets:0
Booting from only image (0xb8010000) ...
as you can see the correct board id is AW5200U, but in target/linux/brcm63xx/image/bcm63xx.mk at line 511 the device is defined like this: define Device/DSL275XB-D1
$(Device/bcm63xx)
DEVICE_TITLE := D-Link DSL-2750B/DSL-2751 rev D1
DEVICE_DTS := dsl-275xb-d
CFE_BOARD_ID := AW5200B
CFE_CHIP_ID := 6318
FLASH_MB := 8
DEVICE_PACKAGES :=
$(B43_PACKAGES) $(USB2_PACKAGES)
endef
TARGET_DEVICES += DSL275XB-D1
so I tried compiling myself the image changing this line: CFE_BOARD_ID := AW5200B
to this: CFE_BOARD_ID := AW5200U
and it worked, my device now has LEDE installed and I've not encountered any problem so far.
So the solution for this problem seems to be very simple: changing that line. Also, I'd be happy to contribute to this project providing you any information you need of this device and/or contributing to the wiki.
The text was updated successfully, but these errors were encountered:
I think that's a mistake, another user has reported his bootlog [[https://forum.openwrt.org/viewtopic.php?id=61763|here]] and it's the same. Also, on this [[https://forum.openwrt.org/viewtopic.php?id=42206|thread]] only one person with revision D1 seems to have been successful installing the image, and another user reports the same error I got too
It's the Board ID my device uses:
CFE version 1.0.38-114.170 for BCM96318 (32bit,SP,BE)
Build Date: 一 4月 8 14:09:33 CST 2013 (root@delta.com)
Copyright (C) 2000-2011 Broadcom Corporation.
HS Serial flash device: name MX25L64, id 0xc217 size 8192KB
Total Flash size: 8192K with 2048 sectors
Flash not used for Auxillary File System
Chip ID: BCM6318B0, MIPS: 333MHz, DDR: 333MHz, Bus: 166MHz
Main Thread: TP0
Total Memory: 67108864 bytes (64MB)
Boot Address: 0xb8000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.2
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Board Id (0-6) : AW5200B
Number of MAC Addresses (1-32) : 11
Base MAC Address : bc:f6:85:5b:2d:f6
PSI Size (1-64) KBytes : 24
Enable Backup PSI [0|1] : 0
System Log Size (0-256) KBytes : 0
Auxillary File System Size Percent: 0
Main Thread Number [0|1] : 0
I have a DSL-2751 (Annex B), not a DSL-2750 (Annex A), so that might be the reason for the different Board IDs. Does this match with those with the AW5200U board ids?
zAxny32:
device: DSL-2750B version D1 EU ([[https://openwrt.org/toh/hwdata/d-link/d-link_dsl-2750b_d1|Techdata]])
LEDE version: 17.01
(I hope I picked the right category)
I tried flashing the image from the link in the techdata page, but the device says it doesn't accept it because of a wrong id, so I connected to the serial pins to see what is the right id and this is the boot log:
HELO
CPUI
L1CI
DRAM
PHYS
PHYE
DDR1
333H
SIZ3
RACE
PASS
ZBSS
CODE
DATA
L12F
MAIN
CFE version 1.0.38-114.170 for BCM96318 (32bit,SP,BE)
Build Date: Thu Mar 28 13:52:02 HKT 2013 (root@ubuntu)
Copyright (C) 2000-2011 Broadcom Corporation.
HS Serial flash device: name MX25L64, id 0xc217 size 8192KB
Total Flash size: 8192K with 2048 sectors
Flash not used for Auxillary File System
Chip ID: BCM6318B0, MIPS: 333MHz, DDR: 333MHz, Bus: 166MHz
Main Thread: TP0
Total Memory: 67108864 bytes (64MB)
Boot Address: 0xb8000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Board Id (0-6) : AW5200U
Number of MAC Addresses (1-32) : 11
Base MAC Address : 6c:19:8f:8d:b8:fc
PSI Size (1-64) KBytes : 24
Enable Backup PSI [0|1] : 0
System Log Size (0-256) KBytes : 0
Auxillary File System Size Percent: 0
Main Thread Number [0|1] : 0
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 1�1�0
udp bind success
g_secs=02
No received any packet
Packet loss:0, noncontinuative packets:0
Booting from only image (0xb8010000) ...
as you can see the correct board id is AW5200U, but in target/linux/brcm63xx/image/bcm63xx.mk at line 511 the device is defined like this:
define Device/DSL275XB-D1
$(Device/bcm63xx)
DEVICE_TITLE := D-Link DSL-2750B/DSL-2751 rev D1
DEVICE_DTS := dsl-275xb-d
CFE_BOARD_ID := AW5200B
CFE_CHIP_ID := 6318
FLASH_MB := 8
DEVICE_PACKAGES :=
$(B43_PACKAGES) $(USB2_PACKAGES)
endef
TARGET_DEVICES += DSL275XB-D1
so I tried compiling myself the image changing this line:
CFE_BOARD_ID := AW5200B
to this:
CFE_BOARD_ID := AW5200U
and it worked, my device now has LEDE installed and I've not encountered any problem so far.
So the solution for this problem seems to be very simple: changing that line. Also, I'd be happy to contribute to this project providing you any information you need of this device and/or contributing to the wiki.
The text was updated successfully, but these errors were encountered: