OpenWrt/LEDE Project

  • Status Unconfirmed
  • Percent Complete
    0%
  • Task Type Bug Report
  • Category Kernel
  • Assigned To No-one
  • Operating System All
  • Severity Critical
  • Priority Very Low
  • Reported Version lede-17.01
  • Due in Version Undecided
  • Due Date Undecided
  • Private
Attached to Project: OpenWrt/LEDE Project
Opened by one - 12.06.2018

FS#1587 - Qca9887 ath10K drive crash

MINIBOX V3.2
CPU:QCA9531
FLASH:16M
RAM:128M
5G chip:QCA9887

 
[    0.000000] Linux version 4.9.107 (root@lede) (gcc version 7.3.0 (lede) ) #0 Sun Jun 10 14:03:23 2018
[    0.000000] MyLoader: sysp=cd03e8c7, boardp=565c9627, parts=9b565cbd
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
[    0.000000] SoC: Qualcomm Atheros QCA9533 ver 2 rev 0
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] On node 0 totalpages: 32768
[    0.000000] free_area_init_node: node 0, pgdat 8041ea74, node_mem_map 81000020
[    0.000000]   Normal zone: 256 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 32768 pages, LIFO batch:7
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line:  board=MINIBOX_V3_2  console=ttyS0,115200 rootfstype=squashfs noinitrd
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 125072K/131072K available (2917K kernel code, 162K rwdata, 760K rodata, 312K init, 270K bss, 6000K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:51
[    0.000000] Clocks: CPU:550.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6950037990 ns
[    0.000011] sched_clock: 32 bits at 275MHz, resolution 3ns, wraps every 7809031678ns
[    0.008273] Calibrating delay loop... 366.18 BogoMIPS (lpj=1830912)
[    0.071079] pid_max: default: 32768 minimum: 301
[    0.076091] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.083069] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.093759] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.104180] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.111370] NET: Registered protocol family 16
[    0.117931] MIPS: machine is Minibox V3.2 board
[    0.127278] registering PCI controller with io_map_base unset
[    0.135112] ar71xx: invalid MDIO id 1
[    0.139031] ar71xx: using random MAC address for eth0
[    0.379364] ar71xx: using random MAC address for eth1
[    0.633989] PCI host bridge to bus 0000:00
[    0.638333] pci_bus 0000:00: root bus resource [mem 0x10000000-0x11ffffff]
[    0.645652] pci_bus 0000:00: root bus resource [io  0x0000]
[    0.651522] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    0.658690] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.667077] pci 0000:00:00.0: [168c:0050] type 00 class 0x028000
[    0.667127] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[    0.667184] pci 0000:00:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[    0.667265] pci 0000:00:00.0: supports D1
[    0.667277] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[    0.667518] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[    0.667552] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x101fffff 64bit]
[    0.675316] pci 0000:00:00.0: BAR 6: assigned [mem 0x10200000-0x1020ffff pref]
[    0.682944] pci 0000:00:00.0: using irq 40 for pin 1
[    0.689027] clocksource: Switched to clocksource MIPS
[    0.695645] NET: Registered protocol family 2
[    0.701316] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.708689] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.715471] TCP: Hash tables configured (established 1024 bind 1024)
[    0.722324] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.728502] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.735483] NET: Registered protocol family 1
[    0.740174] PCI: CLS 0 bytes, default 32
[    0.745440] Crashlog allocated RAM at address 0x3f00000
[    0.752221] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[    0.766885] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.773095] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.793392] io scheduler noop registered
[    0.797534] io scheduler deadline registered (default)
[    0.803385] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    0.810641] console [ttyS0] disabled
[    0.834597] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 1562500) is a 16550A
[    0.843712] console [ttyS0] enabled
[    0.851276] bootconsole [early0] disabled
[    0.869621] m25p80 spi0.0: found w25q128, expected m25p80
[    0.884352] m25p80 spi0.0: w25q128 (16384 Kbytes)
[    0.889600] 5 tp-link partitions found on MTD device spi0.0
[    0.895355] Creating 5 MTD partitions on "spi0.0":
[    0.900350] 0x000000000000-0x000000020000 : "u-boot"
[    0.907217] 0x000000020000-0x00000015df44 : "kernel"
[    0.914412] 0x00000015df44-0x000000ff0000 : "rootfs"
[    0.921531] mtd: device 2 (rootfs) set to be root filesystem
[    0.927429] 1 squashfs-split partitions found on MTD device rootfs
[    0.933909] 0x000000550000-0x000000ff0000 : "rootfs_data"
[    0.941400] 0x000000ff0000-0x000001000000 : "art"
[    0.948172] 0x000000020000-0x000000ff0000 : "firmware"
[    0.956596] libphy: Fixed MDIO Bus: probed
[    0.986045] libphy: ag71xx_mdio: probed
[    1.621997] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd042, driver=Generic PHY]
[    1.632318] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[    2.261593] ag71xx-mdio.1: Found an AR934X built-in switch
[    2.315088] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
[    2.322395] NET: Registered protocol family 17
[    2.327207] 8021q: 802.1Q VLAN Support v1.8
[    2.339807] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    2.349634] Freeing unused kernel memory: 312K
[    2.354223] This architecture does not have kernel memory protection.
[    2.559043] random: fast init done
[    3.046533] init: Console is alive
[    3.050439] init: - watchdog -
[    4.116728] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    4.210493] usbcore: registered new interface driver usbfs
[    4.216263] usbcore: registered new interface driver hub
[    4.221936] usbcore: registered new device driver usb
[    4.234340] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    4.243176] ehci-platform: EHCI generic platform driver
[    4.248701] ehci-platform ehci-platform: EHCI Host Controller
[    4.254754] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[    4.265091] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[    4.299073] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[    4.306607] hub 1-0:1.0: USB hub found
[    4.310952] hub 1-0:1.0: 1 port detected
[    4.316118] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    4.326306] init: - preinit -
[    5.364892] random: procd: uninitialized urandom read (4 bytes read)
[    8.739003] jffs2: notice: (352) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[    8.756844] mount_root: switching to jffs2 overlay
[    8.797645] urandom-seed: Seeding with /etc/urandom.seed
[    8.966151] procd: - early -
[    8.969965] procd: - watchdog -
[    9.642492] procd: - watchdog -
[    9.646084] procd: - ubus -
[    9.790521] random: ubusd: uninitialized urandom read (4 bytes read)
[    9.804891] random: ubusd: uninitialized urandom read (4 bytes read)
[    9.812142] random: ubusd: uninitialized urandom read (4 bytes read)
[    9.819984] procd: - init -
[   10.216209] kmodloader: loading kernel modules from /etc/modules.d/*
[   10.230412] usbcore: registered new interface driver cdc_wdm
[   10.239008] Loading modules backported from Linux version wt-2017-11-01-0-gfe248fc2c180
[   10.247367] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d
[   10.258118] usbcore: registered new interface driver ipheth
[   10.271504] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
[   10.353951] xt_time: kernel timezone is -0000
[   10.361109] usbcore: registered new interface driver cdc_ether
[   10.541738] ip_tables: (C) 2000-2006 Netfilter Core Team
[   10.597904] PPP generic driver version 2.4.2
[   10.605538] NET: Registered protocol family 24
[   10.613271] usbcore: registered new interface driver qmi_wwan
[   10.622421] usbcore: registered new interface driver rndis_host
[   10.661827] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[   10.667870] ath10k_pci 0000:00:00.0: pci irq legacy oper_irq_mode 1 irq_mode 0 reset_mode 0
[   10.943915] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:00:00.0.bin failed with error -2
[   10.955031] ath10k_pci 0000:00:00.0: Falling back to user helper
[   11.050021] firmware ath10k!pre-cal-pci-0000:00:00.0.bin: firmware_loading_store: map pages failed
[   11.059775] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/cal-pci-0000:00:00.0.bin failed with error -2
[   11.070532] ath10k_pci 0000:00:00.0: Falling back to user helper
[   11.253137] firmware ath10k!cal-pci-0000:00:00.0.bin: firmware_loading_store: map pages failed
[   11.262558] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA9887/hw1.0/firmware-6.bin failed with error -2
[   11.273671] ath10k_pci 0000:00:00.0: Falling back to user helper
[   11.455482] firmware ath10k!QCA9887!hw1.0!firmware-6.bin: firmware_loading_store: map pages failed
[   11.474867] ath10k_pci 0000:00:00.0: qca9887 hw1.0 target 0x4100016d chip_id 0x004000ff sub 0000:0000
[   11.484487] ath10k_pci 0000:00:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
[   11.499666] ath10k_pci 0000:00:00.0: firmware ver 10.2.4-1.0-00040 api 5 features no-p2p,ignore-otp,skip-clock-init,mfp,allows-mesh-bcast crc32 3334e5a3
[   11.601094] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA9887/hw1.0/board-2.bin failed with error -2
[   11.611933] ath10k_pci 0000:00:00.0: Falling back to user helper
[   11.726715] firmware ath10k!QCA9887!hw1.0!board-2.bin: firmware_loading_store: map pages failed
[   11.743408] ath10k_pci 0000:00:00.0: board_file api 1 bmi_id N/A crc32 546cca0d
[   11.769404] ath10k_pci 0000:00:00.0: failed to read device EEPROM at 0000
[   11.777300] ath10k_pci 0000:00:00.0: caldata loaded from partition [art]
[   12.830988] ath10k_pci 0000:00:00.0: htt-ver 2.1 wmi-op 5 htt-op 2 cal eeprom max-sta 128 raw 0 hwcrypto 1
[   12.971295] ath: EEPROM regdomain: 0x0
[   12.971307] ath: EEPROM indicates default country code should be used
[   12.971310] ath: doing EEPROM country->regdmn map search
[   12.971326] ath: country maps to regdmn code: 0x3a
[   12.971332] ath: Country alpha2 being used: US
[   12.971336] ath: Regpair used: 0x3a
[   13.127132] ath: EEPROM regdomain: 0x0
[   13.127145] ath: EEPROM indicates default country code should be used
[   13.127149] ath: doing EEPROM country->regdmn map search
[   13.127170] ath: country maps to regdmn code: 0x3a
[   13.127177] ath: Country alpha2 being used: US
[   13.127181] ath: Regpair used: 0x3a
[   13.140052] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[   13.145226] ieee80211 phy1: Atheros AR9531 Rev:2 mem=0xb8100000, irq=47
[   13.157026] kmodloader: done loading kernel modules from /etc/modules.d/*
[   14.893250] urandom_read: 5 callbacks suppressed
[   14.893260] random: jshn: uninitialized urandom read (4 bytes read)
[   23.564137] br-lan: port 1(eth1) entered blocking state
[   23.564157] br-lan: port 1(eth1) entered disabled state
[   23.564594] device eth1 entered promiscuous mode
[   23.565896] br-lan: port 1(eth1) entered blocking state
[   23.565915] br-lan: port 1(eth1) entered forwarding state
[   24.509186] br-lan: port 1(eth1) entered disabled state
[   25.345009] eth1: link up (1000Mbps/Full duplex)
[   25.345068] br-lan: port 1(eth1) entered blocking state
[   25.345079] br-lan: port 1(eth1) entered forwarding state
[   26.610009] ath: EEPROM regdomain: 0x822a
[   26.610022] ath: EEPROM indicates we should expect a country code
[   26.610031] ath: doing EEPROM country->regdmn map search
[   26.610037] ath: country maps to regdmn code: 0x22
[   26.610043] ath: Country alpha2 being used: NZ
[   26.610047] ath: Regpair used: 0x22
[   26.610055] ath: regdomain 0x822a dynamically updated by user
[   26.610158] ath: EEPROM regdomain: 0x822a
[   26.610162] ath: EEPROM indicates we should expect a country code
[   26.610170] ath: doing EEPROM country->regdmn map search
[   26.610176] ath: country maps to regdmn code: 0x22
[   26.610180] ath: Country alpha2 being used: NZ
[   26.610183] ath: Regpair used: 0x22
[   26.610189] ath: regdomain 0x822a dynamically updated by user
[   29.838243] ath10k_pci 0000:00:00.0: failed to read device EEPROM at 0000
[   29.839218] ath10k_pci 0000:00:00.0: caldata loaded from partition [art]
[   31.814735] br-lan: port 2(wlan0) entered blocking state
[   31.814753] br-lan: port 2(wlan0) entered disabled state
[   31.815215] device wlan0 entered promiscuous mode
[   31.863527] br-lan: port 3(wlan1-1) entered blocking state
[   31.863545] br-lan: port 3(wlan1-1) entered disabled state
[   31.864031] device wlan1-1 entered promiscuous mode
[   31.864122] br-lan: port 3(wlan1-1) entered blocking state
[   31.864134] br-lan: port 3(wlan1-1) entered forwarding state
[   32.829121] br-lan: port 3(wlan1-1) entered disabled state
[   35.017706] wlan1: authenticate with 7e:ad:cf:39:2b:82
[   35.031567] wlan1: send auth to 7e:ad:cf:39:2b:82 (try 1/3)
[   35.033829] wlan1: authenticated
[   35.039327] wlan1: associate with 7e:ad:cf:39:2b:82 (try 1/3)
[   35.044025] wlan1: RX AssocResp from 7e:ad:cf:39:2b:82 (capab=0x411 status=0 aid=2)
[   35.044329] wlan1: associated
[   35.075993] wlan1: Limiting TX power to 20 (20 - 0) dBm as advertised by 7e:ad:cf:39:2b:82
[   36.244707] br-lan: port 3(wlan1-1) entered blocking state
[   36.244727] br-lan: port 3(wlan1-1) entered forwarding state
[   39.134490] br-lan: port 2(wlan0) entered blocking state
[   39.134520] br-lan: port 2(wlan0) entered forwarding state
[   62.562748] random: crng init done
[ 1744.900623] ath10k_pci 0000:00:00.0: bss channel survey timed out
[ 1747.940457] ath10k_pci 0000:00:00.0: bss channel survey timed out
[ 1750.980351] ath10k_pci 0000:00:00.0: failed to send pdev bss chan info request
[ 1754.020262] ath10k_pci 0000:00:00.0: failed to set beacon mode for vdev 0: -11
[ 1757.070117] ath10k_pci 0000:00:00.0: failed to set dtim period for vdev 0: -11
[ 1760.100019] ath10k_pci 0000:00:00.0: failed to recalculate rts/cts prot for vdev 0: -11
[ 1763.139784] ath10k_pci 0000:00:00.0: failed to set cts protection for vdev 0: -11
[ 1766.179687] ath10k_pci 0000:00:00.0: failed to set preamble for vdev 0: -11
[ 1769.219577] ath10k_pci 0000:00:00.0: failed to start hw scan: -11
[ 1774.899235] ath10k_pci 0000:00:00.0: failed to send pdev bss chan info request
[ 1777.939092] ath10k_pci 0000:00:00.0: failed to send pdev bss chan info request
[ 1780.986536] ath10k_pci 0000:00:00.0: failed to send pdev bss chan info request
[ 1784.024277] ath10k_pci 0000:00:00.0: failed to set beacon mode for vdev 0: -11
[ 1787.058838] ath10k_pci 0000:00:00.0: failed to set dtim period for vdev 0: -11
[ 1790.098563] ath10k_pci 0000:00:00.0: failed to recalculate rts/cts prot for vdev 0: -11
[ 1793.138413] ath10k_pci 0000:00:00.0: failed to set cts protection for vdev 0: -11
[ 1796.178242] ath10k_pci 0000:00:00.0: failed to set preamble for vdev 0: -11
[ 1800.343496] ath10k_pci 0000:00:00.0: failed to start hw scan: -11
[ 1804.977916] ath10k_pci 0000:00:00.0: failed to send pdev bss chan info request
[ 1808.020380] ath10k_pci 0000:00:00.0: failed to send pdev bss chan info request
[ 1811.057519] ath10k_pci 0000:00:00.0: failed to send pdev bss chan info request
[ 1814.097400] ath10k_pci 0000:00:00.0: failed to set beacon mode for vdev 0: -11
[ 1817.143231] ath10k_pci 0000:00:00.0: failed to set dtim period for vdev 0: -11
[ 1820.177331] ath10k_pci 0000:00:00.0: failed to recalculate rts/cts prot for vdev 0: -11
[ 1823.219063] ath10k_pci 0000:00:00.0: failed to set cts protection for vdev 0: -11
[ 1826.256830] ath10k_pci 0000:00:00.0: failed to set preamble for vdev 0: -11
[ 1834.336429] ath10k_pci 0000:00:00.0: failed to start hw scan: -11
[ 1837.376262] ath10k_pci 0000:00:00.0: failed to send pdev bss chan info request
[ 1840.416093] ath10k_pci 0000:00:00.0: failed to set beacon mode for vdev 0: -11
[ 1843.455991] ath10k_pci 0000:00:00.0: failed to set dtim period for vdev 0: -11
[ 1846.505551] ath10k_pci 0000:00:00.0: failed to recalculate rts/cts prot for vdev 0: -11
[ 1849.535656] ath10k_pci 0000:00:00.0: failed to set cts protection for vdev 0: -11
[ 1852.575507] ath10k_pci 0000:00:00.0: failed to set preamble for vdev 0: -11
[ 1855.775309] ath10k_pci 0000:00:00.0: failed to send pdev bss chan info request
[ 1860.335143] ath10k_pci 0000:00:00.0: failed to send pdev bss chan info request
[ 1863.374943] ath10k_pci 0000:00:00.0: failed to send pdev bss chan info request
[ 1866.414782] ath10k_pci 0000:00:00.0: failed to start hw scan: -11
[ 1869.454614] ath10k_pci 0000:00:00.0: failed to send pdev bss chan info request
[ 1872.496511] ath10k_pci 0000:00:00.0: failed to set beacon mode for vdev 0: -11
[ 1875.534310] ath10k_pci 0000:00:00.0: failed to set dtim period for vdev 0: -11
[ 1878.574185] ath10k_pci 0000:00:00.0: failed to recalculate rts/cts prot for vdev 0: -11
[ 1881.613991] ath10k_pci 0000:00:00.0: failed to set cts protection for vdev 0: -11
[ 1884.653855] ath10k_pci 0000:00:00.0: failed to set preamble for vdev 0: -11
[ 1890.493530] ath10k_pci 0000:00:00.0: failed to send pdev bss chan info request
[ 1893.533390] ath10k_pci 0000:00:00.0: failed to send pdev bss chan info request
[ 1896.573246] ath10k_pci 0000:00:00.0: failed to send pdev bss chan info request
[ 1899.613073] ath10k_pci 0000:00:00.0: failed to set beacon mode for vdev 0: -11
[ 1902.662933] ath10k_pci 0000:00:00.0: failed to set dtim period for vdev 0: -11
[ 1905.692765] ath10k_pci 0000:00:00.0: failed to recalculate rts/cts prot for vdev 0: -11
[ 1908.732738] ath10k_pci 0000:00:00.0: failed to set cts protection for vdev 0: -11
[ 1911.772447] ath10k_pci 0000:00:00.0: failed to set preamble for vdev 0: -11
[ 1914.812252] ath10k_pci 0000:00:00.0: failed to start hw scan: -11
[ 1920.171980] ath10k_pci 0000:00:00.0: failed to send pdev bss chan info request
[ 1923.217262] ath10k_pci 0000:00:00.0: failed to send pdev bss chan info request
[ 1926.251764] ath10k_pci 0000:00:00.0: failed to send pdev bss chan info request
[ 1929.291504] ath10k_pci 0000:00:00.0: failed to set beacon mode for vdev 0: -11
[ 1932.336764] ath10k_pci 0000:00:00.0: failed to set dtim period for vdev 0: -11
[ 1935.371146] ath10k_pci 0000:00:00.0: failed to recalculate rts/cts prot for vdev 0: -11
[ 1938.411007] ath10k_pci 0000:00:00.0: failed to set cts protection for vdev 0: -11
[ 1941.450845] ath10k_pci 0000:00:00.0: failed to set preamble for vdev 0: -11
[ 1944.490643] ath10k_pci 0000:00:00.0: failed to start hw scan: -11
[ 1950.330354] ath10k_pci 0000:00:00.0: failed to send pdev bss chan info request
[ 1953.370196] ath10k_pci 0000:00:00.0: failed to send pdev bss chan info request
[ 1956.409991] ath10k_pci 0000:00:00.0: failed to send pdev bss chan info request
[ 1959.449824] ath10k_pci 0000:00:00.0: failed to set beacon mode for vdev 0: -11
[ 1962.489718] ath10k_pci 0000:00:00.0: failed to set dtim period for vdev 0: -11
[ 1965.529527] ath10k_pci 0000:00:00.0: failed to recalculate rts/cts prot for vdev 0: -11
[ 1968.569397] ath10k_pci 0000:00:00.0: failed to set cts protection for vdev 0: -11
[ 1971.609234] ath10k_pci 0000:00:00.0: failed to set preamble for vdev 0: -11
[ 1975.689202] ath10k_pci 0000:00:00.0: failed to start hw scan: -11
[ 1980.658820] ath10k_pci 0000:00:00.0: failed to send pdev bss chan info request
[ 1983.688670] ath10k_pci 0000:00:00.0: failed to set beacon mode for vdev 0: -11
[ 1986.728592] ath10k_pci 0000:00:00.0: failed to set dtim period for vdev 0: -11
[ 1989.773828] ath10k_pci 0000:00:00.0: failed to recalculate rts/cts prot for vdev 0: -11
[ 1992.808207] ath10k_pci 0000:00:00.0: failed to set cts protection for vdev 0: -11
[ 1995.848059] ath10k_pci 0000:00:00.0: failed to set preamble for vdev 0: -11
[ 2004.087657] ath10k_pci 0000:00:00.0: failed to start hw scan: -11
[ 2007.127466] ath10k_pci 0000:00:00.0: failed to send pdev bss chan info request
[ 2010.167356] ath10k_pci 0000:00:00.0: failed to set beacon mode for vdev 0: -11
[ 2013.207176] ath10k_pci 0000:00:00.0: failed to set dtim period for vdev 0: -11
[ 2016.247043] ath10k_pci 0000:00:00.0: failed to recalculate rts/cts prot for vdev 0: -11
[ 2019.286864] ath10k_pci 0000:00:00.0: failed to set cts protection for vdev 0: -11
[ 2022.326706] ath10k_pci 0000:00:00.0: failed to set preamble for vdev 0: -11
[ 2030.006318] ath10k_pci 0000:00:00.0: failed to start hw scan: -11
[ 2033.046176] ath10k_pci 0000:00:00.0: failed to send pdev bss chan info request
[ 2036.086015] ath10k_pci 0000:00:00.0: failed to set beacon mode for vdev 0: -11
[ 2039.125842] ath10k_pci 0000:00:00.0: failed to set dtim period for vdev 0: -11
[ 2042.165749] ath10k_pci 0000:00:00.0: failed to recalculate rts/cts prot for vdev 0: -11
[ 2045.205527] ath10k_pci 0000:00:00.0: failed to set cts protection for vdev 0: -11
[ 2048.248521] ath10k_pci 0000:00:00.0: failed to set preamble for vdev 0: -11
[ 2054.325056] ath10k_pci 0000:00:00.0: failed to install key for vdev 0 peer 4c:49:e3:d6:b9:4b: -11
[ 2054.325076] wlan0: failed to remove key (0, 4c:49:e3:d6:b9:4b) from hardware (-11)
[ 2054.353286] ath10k_pci 0000:00:00.0: cipher 0 is not supported
[ 2054.353309] ath10k_pci 0000:00:00.0: failed to remove peer wep key 0: -122
[ 2054.353321] ath10k_pci 0000:00:00.0: failed to clear all peer wep keys for vdev 0: -122
[ 2054.353336] ath10k_pci 0000:00:00.0: failed to disassociate station: 4c:49:e3:d6:b9:4b vdev 0: -122
[ 2054.353342] ------------[ cut here ]------------
[ 2054.353535] WARNING: CPU: 0 PID: 1647 at backports-2017-11-01/net/mac80211/sta_info.c:993 sta_set_sinfo+0x8d4/0x9cc [mac80211]
[ 2054.353540] Modules linked in: ath9k ath9k_common pppoe ppp_async ath9k_hw ath10k_pci ath10k_core ath rndis_host qmi_wwan pppox ppp_generic mac80211 iptable_nat iptable_mangle iptable_filter ipt_REJECT ipt_MASQUERADE ip_tables cfg80211 cdc_ether xt_time xt_tcpudp xt_state xt_nat xt_multiport xt_mark xt_mac xt_limit xt_conntrack xt_comment xt_TCPMSS xt_REDIRECT xt_LOG x_tables usbnet slhc nf_reject_ipv4 nf_nat_redirect nf_nat_masquerade_ipv4 nf_conntrack_ipv4 nf_nat_ipv4 nf_nat nf_log_ipv4 nf_log_common nf_defrag_ipv4 nf_conntrack_rtcache nf_conntrack ipheth crc_ccitt compat cdc_wdm ledtrig_usbport ehci_platform ehci_hcd gpio_button_hotplug usbcore nls_base usb_common mii
[ 2054.353728] CPU: 0 PID: 1647 Comm: hostapd Not tainted 4.9.107 #0
[ 2054.353733] Stack : 80487672 00000035 00000000 00000001 8654828c 803febc7 803b75d0 0000066f
[ 2054.353760]         804837c0 000003e1 00000000 00000008 00000000 800a976c 803bce08 80400000
[ 2054.353785]         00000003 000003e1 803bafc0 876d5b0c 00000000 800d75cc 80487672 00000072
[ 2054.353811]         00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 2054.353834]         00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 2054.353857]         ...
[ 2054.353865] Call Trace:
[ 2054.353880] [<8006b5c0>] show_stack+0x70/0x8c
[ 2054.353917] [<80080524>] __warn+0x110/0x118
[ 2054.353931] [<800805c0>] warn_slowpath_null+0x1c/0x2c
[ 2054.354036] [<87606f24>] sta_set_sinfo+0x8d4/0x9cc [mac80211]
[ 2054.354134] [<87604978>] sta_info_get_bss+0x18/0x6c [mac80211]
[ 2054.354233] [<876070fc>] sta_info_destroy_addr_bss+0x38/0x60 [mac80211]
[ 2054.354377] [<8754e2e0>] cfg80211_check_station_change+0x2364/0x3240 [cfg80211]
[ 2054.354414] ---[ end trace 76e3fd41f87c33dc ]---
[ 2057.364905] ath10k_pci 0000:00:00.0: failed to delete peer 4c:49:e3:d6:b9:4b for vdev 0: -11
[ 2057.364942] ath10k_pci 0000:00:00.0: found sta peer 4c:49:e3:d6:b9:4b (ptr 8677b600 id 229) entry on vdev 0 after it was supposedly removed
[ 2057.366192] ------------[ cut here ]------------
[ 2057.366384] WARNING: CPU: 0 PID: 1647 at backports-2017-11-01/net/mac80211/sta_info.c:1001 sta_set_sinfo+0x924/0x9cc [mac80211]
[ 2057.366389] Modules linked in: ath9k ath9k_common pppoe ppp_async ath9k_hw ath10k_pci ath10k_core ath rndis_host qmi_wwan pppox ppp_generic mac80211 iptable_nat iptable_mangle iptable_filter ipt_REJECT ipt_MASQUERADE ip_tables cfg80211 cdc_ether xt_time xt_tcpudp xt_state xt_nat xt_multiport xt_mark xt_mac xt_limit xt_conntrack xt_comment xt_TCPMSS xt_REDIRECT xt_LOG x_tables usbnet slhc nf_reject_ipv4 nf_nat_redirect nf_nat_masquerade_ipv4 nf_conntrack_ipv4 nf_nat_ipv4 nf_nat nf_log_ipv4 nf_log_common nf_defrag_ipv4 nf_conntrack_rtcache nf_conntrack ipheth crc_ccitt compat cdc_wdm ledtrig_usbport ehci_platform ehci_hcd gpio_button_hotplug usbcore nls_base usb_common mii
[ 2057.366577] CPU: 0 PID: 1647 Comm: hostapd Tainted: G        W       4.9.107 #0
[ 2057.366582] Stack : 80487672 00000043 00000000 00000001 8654828c 803febc7 803b75d0 0000066f
[ 2057.366609]         804837c0 000003e9 00000000 00000008 00000000 800a976c 803bce08 80400000
[ 2057.366634]         00000003 000003e9 803bafc0 876d5b0c 00000000 800d75cc 80487672 00000073
[ 2057.366660]         00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 2057.366683]         00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 2057.366706]         ...
[ 2057.366714] Call Trace:
[ 2057.366728] [<8006b5c0>] show_stack+0x70/0x8c
[ 2057.366763] [<80080524>] __warn+0x110/0x118
[ 2057.366777] [<800805c0>] warn_slowpath_null+0x1c/0x2c
[ 2057.366888] [<87606f74>] sta_set_sinfo+0x924/0x9cc [mac80211]
[ 2057.366987] [<87604978>] sta_info_get_bss+0x18/0x6c [mac80211]
[ 2057.367086] [<876070fc>] sta_info_destroy_addr_bss+0x38/0x60 [mac80211]
[ 2057.367225] [<8754e2e0>] cfg80211_check_station_change+0x2364/0x3240 [cfg80211]
[ 2057.367262] ---[ end trace 76e3fd41f87c33dd ]---
[ 2060.404774] ath10k_pci 0000:00:00.0: failed to start hw scan: -11
[ 2063.444576] ath10k_pci 0000:00:00.0: failed to set beacon mode for vdev 0: -11
[ 2066.484459] ath10k_pci 0000:00:00.0: failed to set dtim period for vdev 0: -11
[ 2069.524270] ath10k_pci 0000:00:00.0: failed to recalculate rts/cts prot for vdev 0: -11
[ 2072.564091] ath10k_pci 0000:00:00.0: failed to set cts protection for vdev 0: -11
[ 2075.603941] ath10k_pci 0000:00:00.0: failed to set preamble for vdev 0: -11
[ 2078.643808] ath10k_pci 0000:00:00.0: failed to send pdev bss chan info request
[ 2081.683658] ath10k_pci 0000:00:00.0: failed to set beacon mode for vdev 0: -11
[ 2084.723443] ath10k_pci 0000:00:00.0: failed to set dtim period for vdev 0: -11
[ 2087.771438] ath10k_pci 0000:00:00.0: failed to recalculate rts/cts prot for vdev 0: -11
[ 2090.803177] ath10k_pci 0000:00:00.0: failed to set cts protection for vdev 0: -11
[ 2093.842997] ath10k_pci 0000:00:00.0: failed to set preamble for vdev 0: -11
[ 2102.162502] ath10k_pci 0000:00:00.0: failed to start hw scan: -11
[ 2105.202331] ath10k_pci 0000:00:00.0: failed to send pdev bss chan info request
[ 2108.242168] ath10k_pci 0000:00:00.0: failed to set beacon mode for vdev 0: -11
[ 2111.282032] ath10k_pci 0000:00:00.0: failed to set dtim period for vdev 0: -11
[ 2114.321878] ath10k_pci 0000:00:00.0: failed to recalculate rts/cts prot for vdev 0: -11
[ 2117.361702] ath10k_pci 0000:00:00.0: failed to set cts protection for vdev 0: -11
[ 2120.401502] ath10k_pci 0000:00:00.0: failed to set preamble for vdev 0: -11
[ 2128.401051] ath10k_pci 0000:00:00.0: failed to start hw scan: -11
[ 2131.450938] ath10k_pci 0000:00:00.0: failed to send pdev bss chan info request
[ 2134.480713] ath10k_pci 0000:00:00.0: failed to set beacon mode for vdev 0: -11
[ 2137.520545] ath10k_pci 0000:00:00.0: failed to set dtim period for vdev 0: -11
[ 2140.560510] ath10k_pci 0000:00:00.0: failed to recalculate rts/cts prot for vdev 0: -11
[ 2143.600263] ath10k_pci 0000:00:00.0: failed to set cts protection for vdev 0: -11
[ 2146.640040] ath10k_pci 0000:00:00.0: failed to set preamble for vdev 0: -11
[ 2155.199617] ath10k_pci 0000:00:00.0: failed to start hw scan: -11
[ 2158.239437] ath10k_pci 0000:00:00.0: failed to send pdev bss chan info request
[ 2161.279214] ath10k_pci 0000:00:00.0: failed to set beacon mode for vdev 0: -11
[ 2164.319096] ath10k_pci 0000:00:00.0: failed to set dtim period for vdev 0: -11
[ 2167.358866] ath10k_pci 0000:00:00.0: failed to recalculate rts/cts prot for vdev 0: -11
[ 2170.398688] ath10k_pci 0000:00:00.0: failed to set cts protection for vdev 0: -11
[ 2173.438543] ath10k_pci 0000:00:00.0: failed to set preamble for vdev 0: -11
[ 2181.598039] ath10k_pci 0000:00:00.0: failed to start hw scan: -11
[ 2184.637881] ath10k_pci 0000:00:00.0: failed to send pdev bss chan info request
[ 2187.677688] ath10k_pci 0000:00:00.0: failed to set beacon mode for vdev 0: -11
[ 2190.727568] ath10k_pci 0000:00:00.0: failed to set dtim period for vdev 0: -11
[ 2193.757337] ath10k_pci 0000:00:00.0: failed to recalculate rts/cts prot for vdev 0: -11
[ 2196.797183] ath10k_pci 0000:00:00.0: failed to set cts protection for vdev 0: -11
[ 2199.837021] ath10k_pci 0000:00:00.0: failed to set preamble for vdev 0: -11
[ 2203.516915] ath10k_pci 0000:00:00.0: failed to send pdev bss chan info request

Trying to replace many firmware versions, but always this way, it will collapse for a while.

Each crash has the following error log

[ 1744.900623] ath10k_pci 0000:00:00.0: bss channel survey timed out
[ 1747.940457] ath10k_pci 0000:00:00.0: bss channel survey timed out
[ 1750.980351] ath10k_pci 0000:00:00.0: failed to send pdev bss chan info request
[ 1754.020262] ath10k_pci 0000:00:00.0: failed to set beacon mode for vdev 0: -11
[ 1757.070117] ath10k_pci 0000:00:00.0: failed to set dtim period for vdev 0: -11
[ 1760.100019] ath10k_pci 0000:00:00.0: failed to recalculate rts/cts prot for vdev 0: -11
[ 1763.139784] ath10k_pci 0000:00:00.0: failed to set cts protection for vdev 0: -11
[ 1766.179687] ath10k_pci 0000:00:00.0: failed to set preamble for vdev 0: -11
[ 1769.219577] ath10k_pci 0000:00:00.0: failed to start hw scan: -11
[ 1774.899235] ath10k_pci 0000:00:00.0: failed to send pdev bss chan info request
[ 1777.939092] ath10k_pci 0000:00:00.0: failed to send pdev bss chan info request
[ 1780.986536] ath10k_pci 0000:00:00.0: failed to send pdev bss chan info request
[ 1784.024277] ath10k_pci 0000:00:00.0: failed to set beacon mode for vdev 0: -11

Loading...

Available keyboard shortcuts

Tasklist

Task Details

Task Editing