You signed in with another tab or window. Reload to refresh your session.You signed out in another tab or window. Reload to refresh your session.You switched accounts on another tab or window. Reload to refresh your session.Dismiss alert
hello *,
just checked a new snapshot of openWRT-lede
and found, that the version from mon-/tuesday
09/10.04. is not able to flash.
The older version r6433-4fd8722056 mid of march
flashes flawlessly.
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
��� 0
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
��� 0
you are not alone,
thanks for reporting this issue #10645
edit:
I didn't notice that this was opened by a bot 😅
and I was actually looking for bugs related to the current lzma error 1 issues
like #10634 for this device
This issue should be closed imo it's probably not relevant anymore and/or will be fixed with the newer issue.
owrt07:
hello *,
just checked a new snapshot of openWRT-lede
and found, that the version from mon-/tuesday
09/10.04. is not able to flash.
The older version r6433-4fd8722056 mid of march
flashes flawlessly.
Maybe someone has a hint where to dig?
kernel changed from 4.9 to 4.14 ...
The serial console booting the new
U-Boot 1.1.3 (Apr 15 2011 - 10:39:36) (ALPHA)
SVN revision: 516
Target board: WRG-N39
Board: Ralink APSoC DRAM: 64 MB
spi_wait_nsec: 30
spi device id:
find flash: MX25L6405D
raspi_read: from:30000 len:1000
.raspi_read: from:30000 len:1000
.============================================
Ralink UBoot Version: 3.3
ASIC 3883_MP (MAC to REALTEK Mode)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Apr 15 2011 Time:10:39:36
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768
gpio_init: write 0x00001801
gpio_init: write 0x0000185d to GPIOMODE(0xb0000060)
Initializing RTL8367 GbE switch ...
Setting RTL8367RB RGMII Delay time tx:1,rx0
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
��� 0
3: System Boot system code via Flash.
Booting image at bc050000 ...
raspi_read: from:50000 len:40
.raspi_read: from:50000 len:c
.raspi_read: from:50000 len:359bbe
......................................................We have SEAMA, Image Size = 3513214
Verifying Checksum ...
Uncompressing SEAMA linux.lzma ... LZMA ERROR 1 - must RESET board to recover
and the version r6433-4fd8722056.
U-Boot 1.1.3 (Apr 15 2011 - 10:39:36) (ALPHA)
SVN revision: 516
Target board: WRG-N39
Board: Ralink APSoC DRAM: 64 MB
spi_wait_nsec: 30
spi device id:
find flash: MX25L6405D
raspi_read: from:30000 len:1000
.raspi_read: from:30000 len:1000
.============================================
Ralink UBoot Version: 3.3
ASIC 3883_MP (MAC to REALTEK Mode)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Apr 15 2011 Time:10:39:36
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768
gpio_init: write 0x00001801
gpio_init: write 0x0000185d to GPIOMODE(0xb0000060)
Initializing RTL8367 GbE switch ...
Setting RTL8367RB RGMII Delay time tx:1,rx0
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
��� 0
3: System Boot system code via Flash.
Booting image at bc050000 ...
raspi_read: from:50000 len:40
.raspi_read: from:50000 len:c
.raspi_read: from:50000 len:33e05e
....................................................We have SEAMA, Image Size = 3399710
Verifying Checksum ...
Uncompressing SEAMA linux.lzma ... OK
Transferring control to Linux (at address 80000000) ...
Giving linux memsize in MB, 64
Starting kernel ...
[ 0.000000] Linux version 4.9.86 (buildbot@buildslave) (gcc version 7.3.0 (OpenWrt GCC 7.3.0
Any help welcome.
thx
The text was updated successfully, but these errors were encountered: