Skip to content
New issue

Have a question about this project? Sign up for a free GitHub account to open an issue and contact its maintainers and the community.

By clicking “Sign up for GitHub”, you agree to our terms of service and privacy statement. We’ll occasionally send you account related emails.

Already on GitHub? Sign in to your account

FS#1439 - GL.iNet GL-B1300 Ethernet not working #6402

Closed
openwrt-bot opened this issue Mar 17, 2018 · 0 comments
Closed

FS#1439 - GL.iNet GL-B1300 Ethernet not working #6402

openwrt-bot opened this issue Mar 17, 2018 · 0 comments
Labels

Comments

@openwrt-bot
Copy link

bobafetthotmail1:

I've compiled from latest sources (r6469-5862f01) and flashed on the device. Then tried with the latest snapshot build, the result is the same.

After it has done rebooting ethernet isn't working anymore. Connecting/disconnecting cables does nothing, not even new messages in dmesg.
From the uboot environment, ethernet works fine.

I connect to the device with the serial console, this is bootlog and some commands to show that the device does not have ethernet up.

Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.1.1-00117
S - IMAGE_VARIANT_STRING=DAABANAZA
S - OEM_IMAGE_VERSION_STRING=CRM
S - Boot Config, 0x00000021
S - Reset status Config, 0x00000010
S - Core 0 Frequency, 0 MHz
B - 261 - PBL, Start
B - 1338 - bootable_media_detect_entry, Start
B - 1678 - bootable_media_detect_success, Start
B - 1692 - elf_loader_entry, Start
B - 5069 - auth_hash_seg_entry, Start
B - 7210 - auth_hash_seg_exit, Start
B - 578929 - elf_segs_hash_verify_entry, Start
B - 696660 - PBL, End
B - 696683 - SBL1, Start
B - 787432 - pm_device_init, Start
D - 7 - pm_device_init, Delta
B - 788959 - boot_flash_init, Start
D - 54277 - boot_flash_init, Delta
B - 847376 - boot_config_data_table_init, Start
D - 3837 - boot_config_data_table_init, Delta - (419 Bytes)
B - 854589 - clock_init, Start
D - 7570 - clock_init, Delta
B - 866657 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:0
B - 870070 - sbl1_ddr_set_params, Start
B - 875167 - cpr_init, Start
D - 2 - cpr_init, Delta
B - 879548 - Pre_DDR_clock_init, Start
D - 5 - Pre_DDR_clock_init, Delta
D - 13175 - sbl1_ddr_set_params, Delta
B - 893285 - pm_driver_init, Start
D - 2 - pm_driver_init, Delta
B - 963512 - sbl1_wait_for_ddr_training, Start
D - 28 - sbl1_wait_for_ddr_training, Delta
B - 978987 - Image Load, Start
D - 140781 - QSEE Image Loaded, Delta - (274048 Bytes)
B - 1120195 - Image Load, Start
D - 1438 - SEC Image Loaded, Delta - (2048 Bytes)
B - 1130588 - Image Load, Start
D - 196809 - APPSBL Image Loaded, Delta - (402063 Bytes)
B - 1327792 - QSEE Execution, Start
D - 60 - QSEE Execution, Delta
B - 1334034 - SBL1, End
D - 639429 - SBL1, Delta
S - Flash Throughput, 2002 KB/s (678578 Bytes, 338844 us)
S - DDR Frequency, 537 MHz

U-Boot 2012.07 [Chaos Calmer 15.05.1,r35193] (Dec 19 2017 - 20:17:41)

smem ram ptable found: ver: 1 len: 3
DRAM: 256 MiB
machid : 0x8010000
NAND: SF: Detected MX25L25635E with page size 4 KiB, total 32 MiB
ipq_spi: page_size: 0x100, sector_size: 0x1000, size: 0x2000000
32 MiB
MMC:
In: serial
Out: serial
Err: serial
machid: 8010000
flash_type: 0

Net: MAC0 addr:e4:95:6e:43:30:3a
PHY ID1: 0x4d
PHY ID2: 0xd0b1
ipq40xx_ess_sw_init done
eth0
Hit "gl" key to stop booting: 0

SF: Detected MX25L25635E with page size 4 KiB, total 32 MiB
Checking calibration status...
Device have calibrated,checking test status...
Device haven tested, checking MAC info...
Device have MAC info, starting firmware...

eth0 PHY0 Down Speed :10 Half duplex
eth0 PHY1 Down Speed :10 Half duplex
eth0 PHY2 up Speed :1000 Full duplex
eth0 PHY3 Down Speed :10 Half duplex
eth0 PHY4 Down Speed :10 Half duplex
Using eth0 device
ping failed; host 192.168.1.2 is not alive

eth0 PHY0 Down Speed :10 Half duplex
eth0 PHY1 Down Speed :10 Half duplex
eth0 PHY2 up Speed :1000 Full duplex
eth0 PHY3 Down Speed :10 Half duplex
eth0 PHY4 Down Speed :10 Half duplex
Using eth0 device
ping failed; host 192.168.1.2 is not alive

eth0 PHY0 Down Speed :10 Half duplex
eth0 PHY1 Down Speed :10 Half duplex
eth0 PHY2 up Speed :1000 Full duplex
eth0 PHY3 Down Speed :10 Half duplex
eth0 PHY4 Down Speed :10 Half duplex
Using eth0 device
ping failed; host 192.168.1.2 is not alive

SF: Detected MX25L25635E with page size 4 KiB, total 32 MiB

Booting kernel from FIT Image at 84000000 ...

Using 'config@1' configuration
Trying 'kernel@1' kernel subimage
Description: ARM OpenWrt Linux-4.14.25
Type: Kernel Image
Compression: gzip compressed
Data Start: 0x840000e4
Data Size: 3025863 Bytes = 2.9 MiB
Architecture: ARM
OS: Linux
Load Address: 0x80208000
Entry Point: 0x80208000
Hash algo: crc32
Hash value: 0f3183e0
Hash algo: sha1
Hash value: 07910a0cb439c359762a9ef4e068ee490274a8c7
Verifying Hash Integrity ... crc32+ sha1+ OK

Flattened Device Tree from FIT Image at 84000000

Using 'config@1' configuration
Trying 'fdt@1' FDT blob subimage
Description: ARM OpenWrt glinet_gl-b1300 device tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x842e2de8
Data Size: 15859 Bytes = 15.5 KiB
Architecture: ARM
Hash algo: crc32
Hash value: e1ee0892
Hash algo: sha1
Hash value: a4ae2c4f6e123271dcf43d1e88cd9f2d53a8b60e
Verifying Hash Integrity ... crc32+ sha1+ OK
Booting using the fdt blob at 0x842e2de8
Uncompressing Kernel Image ... OK
Loading Device Tree to 86ff9000, end 86fffdf2 ... OK
ipq: fdt fixup unable to find compatible node
Using machid 0x8010000 from environment

Starting kernel ...

[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.14.25 (buildbot@builds) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r6460-bf4aa52)) #0 SMP Wed Mar 14 23:42:41 2018
[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt: Machine model: GL.iNet GL-B1300
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] random: get_random_bytes called from start_kernel+0x88/0x3c4 with crng_init=0
[ 0.000000] percpu: Embedded 15 pages/cpu @cfdb0000 s29324 r8192 d23924 u61440
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 60928
[ 0.000000] Kernel command line: rootfsname=rootfs rootwait
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 235712K/245760K available (4354K kernel code, 146K rwdata, 1204K rodata, 1024K init, 252K bss, 10048K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xd0800000 - 0xff800000 ( 752 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0208000 - 0xc0740b88 (5347 kB)
[ 0.000000] .init : 0xc0900000 - 0xc0a00000 (1024 kB)
[ 0.000000] .data : 0xc0a00000 - 0xc0a24840 ( 147 kB)
[ 0.000000] .bss : 0xc0a26000 - 0xc0a652f4 ( 253 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] arch_timer: cp15 timer(s) running at 48.00MHz (virt).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xb11fd3bfb, max_idle_ns: 440795203732 ns
[ 0.000008] sched_clock: 56 bits at 48MHz, resolution 20ns, wraps every 4398046511096ns
[ 0.000022] Switching to timer-based delay loop, resolution 20ns
[ 0.000248] Calibrating delay loop (skipped), value calculated using timer frequency.. 96.00 BogoMIPS (lpj=480000)
[ 0.000267] pid_max: default: 32768 minimum: 301
[ 0.000410] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000427] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.001036] CPU: Testing write buffer coherency: ok
[ 0.001665] Setting up static identity map for 0x80300000 - 0x80300060
[ 0.001797] Hierarchical SRCU implementation.
[ 0.002372] smp: Bringing up secondary CPUs ...
[ 0.004876] smp: Brought up 1 node, 4 CPUs
[ 0.004895] SMP: Total of 4 processors activated (384.00 BogoMIPS).
[ 0.004904] CPU: All CPU(s) started in SVC mode.
[ 0.008623] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[ 0.008798] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.008820] futex hash table entries: 1024 (order: 4, 65536 bytes)
[ 0.009019] pinctrl core: initialized pinctrl subsystem
[ 0.009964] NET: Registered protocol family 16
[ 0.010252] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.011286] cpuidle: using governor ladder
[ 0.011328] cpuidle: using governor menu
[ 0.027441] msm_bus_fabric_init_driver
[ 0.028041] usbcore: registered new interface driver usbfs
[ 0.028100] usbcore: registered new interface driver hub
[ 0.028178] usbcore: registered new device driver usb
[ 0.028225] pps_core: LinuxPPS API ver. 1 registered
[ 0.028235] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti giometti@linux.it
[ 0.028259] PTP clock support registered
[ 0.029344] clocksource: Switched to clocksource arch_sys_counter
[ 0.030220] NET: Registered protocol family 2
[ 0.030909] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.030953] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.031002] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.031110] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.031147] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.031345] NET: Registered protocol family 1
[ 0.032352] No memory allocated for crashlog
[ 0.032489] workingset: timestamp_bits=30 max_order=16 bucket_order=0
[ 0.035689] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.035706] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.036777] random: fast init done
[ 0.040618] io scheduler noop registered
[ 0.040635] io scheduler deadline registered (default)
[ 0.043314] tcsr 1949000.tcsr: setting wifi_glb_cfg = 41000000
[ 0.043402] tcsr 194b000.tcsr: setting usb hs phy mode select = e700e7
[ 0.043476] tcsr 1953000.ess_tcsr: setting ess interface select = 0
[ 0.043556] tcsr 1957000.tcsr: setting wifi_noc_memtype_m0_m2 = 2222222
[ 0.043776] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.045540] msm_serial 78af000.serial: msm_serial: detected port #0
[ 0.045588] msm_serial 78af000.serial: uartclk = 1843200
[ 0.045642] 78af000.serial: ttyMSM0 at MMIO 0x78af000 (irq = 25, base_baud = 115200) is a MSM
[ 0.045669] msm_serial: console setup on port #0
[ 0.547847] console [ttyMSM0] enabled
[ 0.552768] msm_serial: driver initialized
[ 0.560280] loop: module loaded
[ 0.561329] spi_qup 78b5000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64
[ 0.564286] m25p80 spi0.0: mx25l25635e (32768 Kbytes)
[ 0.570495] 9 fixed-partitions partitions found on MTD device spi0.0
[ 0.575348] Creating 9 MTD partitions on "spi0.0":
[ 0.581802] 0x000000000000-0x000000040000 : "SBL1"
[ 0.587034] 0x000000040000-0x000000060000 : "MIBIB"
[ 0.591709] 0x000000060000-0x0000000c0000 : "QSEE"
[ 0.596477] 0x0000000c0000-0x0000000d0000 : "CDT"
[ 0.601336] 0x0000000d0000-0x0000000e0000 : "DDRPARAMS"
[ 0.606089] 0x0000000e0000-0x0000000f0000 : "APPSBLENV"
[ 0.611168] 0x0000000f0000-0x000000170000 : "APPSBL"
[ 0.616320] 0x000000170000-0x000000180000 : "ART"
[ 0.621572] 0x000000180000-0x000002000000 : "firmware"
[ 0.626383] 2 fit-fw partitions found on MTD device firmware
[ 0.630673] 0x000000180000-0x000000470000 : "kernel"
[ 0.637102] 0x000000466f00-0x000002000000 : "rootfs"
[ 0.641939] mtd: device 10 (rootfs) set to be root filesystem
[ 0.646514] 1 squashfs-split partitions found on MTD device rootfs
[ 0.652020] 0x0000006b0000-0x000002000000 : "rootfs_data"
[ 0.659288] libphy: ipq40xx_mdio: probed
[ 0.688293] ESS reset ok!
[ 0.721290] ESS reset ok!
[ 1.149729] libphy: Fixed MDIO Bus: probed
[ 1.153419] libphy: PHY 90000.mdio:04 not found
[ 1.229594] ------------[ cut here ]------------
[ 1.229642] WARNING: CPU: 1 PID: 1 at mm/vmalloc.c:1525 release_nodes+0x198/0x1bc
[ 1.233285] Trying to vfree() nonexistent vm area (d08e8000)
[ 1.240687] Modules linked in:
[ 1.246389] CPU: 1 PID: 1 Comm: swapper/0 Not tainted 4.14.25 #0
[ 1.249255] Hardware name: Generic DT based system
[ 1.255442] [] (unwind_backtrace) from [] (show_stack+0x10/0x14)
[ 1.260036] [] (show_stack) from [] (dump_stack+0x88/0x9c)
[ 1.267931] [] (dump_stack) from [] (__warn+0xe4/0x100)
[ 1.274959] [] (__warn) from [] (warn_slowpath_fmt+0x38/0x48)
[ 1.281819] [] (warn_slowpath_fmt) from [] (release_nodes+0x198/0x1bc)
[ 1.289463] [] (release_nodes) from [] (really_probe+0x1a8/0x27c)
[ 1.297618] [] (really_probe) from [] (__driver_attach+0x8c/0xb0)
[ 1.305517] [] (__driver_attach) from [] (bus_for_each_dev+0x4c/0xa0)
[ 1.313331] [] (bus_for_each_dev) from [] (bus_add_driver+0xe8/0x200)
[ 1.321489] [] (bus_add_driver) from [] (driver_register+0xa8/0xe4)
[ 1.329646] [] (driver_register) from [] (do_one_initcall+0xc0/0x184)
[ 1.337465] [] (do_one_initcall) from [] (kernel_init_freeable+0x13c/0x1d0)
[ 1.345796] [] (kernel_init_freeable) from [] (kernel_init+0x8/0x110)
[ 1.354301] [] (kernel_init) from [] (ret_from_fork+0x14/0x2c)
[ 1.362702] ---[ end trace 250c0be6176c0372 ]---
[ 1.370119] ess_edma: probe of c080000.edma failed with error -5
[ 1.375478] i2c /dev entries driver
[ 1.410267] NET: Registered protocol family 10
[ 1.411725] Segment Routing with IPv6
[ 1.413712] NET: Registered protocol family 17
[ 1.417400] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 1.422085] 8021q: 802.1Q VLAN Support v1.8
�[ 1.449573] VFS: Mounted root (squashfs filesystem) readonly on device 31:10.
[ 1.451147] Freeing unused kernel memory: 1024K
[ 2.306363] init: Console is alive
[ 2.306597] init: - watchdog -
[ 3.773901] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 4.319843] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 4.320433] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 4.326325] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f665 hci version 0x100 quirks 0x02010010
[ 4.332940] xhci-hcd xhci-hcd.0.auto: irq 94, io mem 0x08a00000
[ 4.348359] hub 1-0:1.0: USB hub found
[ 4.349153] hub 1-0:1.0: 1 port detected
[ 4.352351] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 4.355199] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 4.360611] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 4.368563] hub 2-0:1.0: USB hub found
[ 4.376445] hub 2-0:1.0: 1 port detected
[ 4.499902] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 4.500448] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
[ 4.506216] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f665 hci version 0x100 quirks 0x02010010
[ 4.512944] xhci-hcd xhci-hcd.1.auto: irq 95, io mem 0x06000000
[ 4.521469] hub 3-0:1.0: USB hub found
[ 4.526592] hub 3-0:1.0: 1 port detected
[ 4.530786] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 4.534454] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
[ 4.539946] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[ 4.547821] hub 4-0:1.0: USB hub found
[ 4.555681] hub 4-0:1.0: config failed, hub doesn't have any ports! (err -19)
[ 4.560984] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 4.579575] init: - preinit -
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 9.186982] jffs2: notice: (161) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 1 orphan) and 1 of xref (1 dead, 0 orphan) found.
[ 9.208874] mount_root: switching to jffs2 overlay
[ 9.230511] overlayfs: upper fs does not support tmpfile.
[ 9.244336] urandom-seed: Seeding with /etc/urandom.seed
[ 9.317375] procd: - early -
[ 9.317514] procd: - watchdog -
[ 9.980551] procd: - watchdog -
[ 9.983341] procd: - ubus -
[ 10.087188] procd: - init -
Please press Enter to activate this console.
[ 10.271602] kmodloader: loading kernel modules from /etc/modules.d/*
[ 10.274673] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 10.703428] Loading modules backported from Linux version wt-2017-11-01-0-gfe248fc2c180
[ 10.703465] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d
[ 10.712114] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 11.083361] nf_conntrack version 0.5.0 (4096 buckets, 16384 max)
[ 11.311032] xt_time: kernel timezone is -0000
[ 11.532737] PPP generic driver version 2.4.2
[ 11.533719] NET: Registered protocol family 24
[ 11.725866] ath10k_ahb a000000.wifi: Direct firmware load for ath10k/QCA4019/hw1.0/firmware-6.bin failed with error -2
[ 11.725917] ath10k_ahb a000000.wifi: Falling back to user helper
[ 11.766796] firmware ath10k!QCA4019!hw1.0!firmware-6.bin: firmware_loading_store: map pages failed
[ 12.305593] ath10k_ahb a000000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003900ff sub 0000:0000
[ 12.305639] ath10k_ahb a000000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
[ 12.318443] ath10k_ahb a000000.wifi: firmware ver 10.4-3.4-00104 api 5 features no-p2p,mfp,peer-flow-ctrl,btcoex-param,allows-mesh-bcast,no-ps crc32 6c332c67
[ 12.364240] ath10k_ahb a000000.wifi: board_file api 2 bmi_id 0:16 crc32 b4b4d99e
[ 13.712909] ath10k_ahb a000000.wifi: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 512 raw 0 hwcrypto 1
[ 13.924563] ath10k_ahb a800000.wifi: Direct firmware load for ath10k/QCA4019/hw1.0/firmware-6.bin failed with error -2
[ 13.924611] ath10k_ahb a800000.wifi: Falling back to user helper
[ 14.058909] firmware ath10k!QCA4019!hw1.0!firmware-6.bin: firmware_loading_store: map pages failed
[ 14.059172] ath10k_ahb a800000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003900ff sub 0000:0000
[ 14.066880] ath10k_ahb a800000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
[ 14.081139] ath10k_ahb a800000.wifi: firmware ver 10.4-3.4-00104 api 5 features no-p2p,mfp,peer-flow-ctrl,btcoex-param,allows-mesh-bcast,no-ps crc32 6c332c67
[ 14.125418] ath10k_ahb a800000.wifi: board_file api 2 bmi_id 0:17 crc32 b4b4d99e
[ 15.473395] ath10k_ahb a800000.wifi: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 512 raw 0 hwcrypto 1
[ 15.542473] kmodloader: done loading kernel modules from /etc/modules.d/*

BusyBox v1.27.2 () built-in shell (ash)


| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -| || | | || || |
|
_____|| |
||||___||| |____|
|
| W I R E L E S S F R E E D O M

OpenWrt SNAPSHOT, r6469-5862f01

=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.

root@OpenWrt:/# ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
4: wlan0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000
link/ether e4:95:6e:43:30:3a brd ff:ff:ff:ff:ff:ff
5: wlan1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000
link/ether e4:95:6e:43:30:3b brd ff:ff:ff:ff:ff:ff
root@OpenWrt:/# uci show network
network.loopback=interface
network.loopback.ifname='lo'
network.loopback.proto='static'
network.loopback.ipaddr='127.0.0.1'
network.loopback.netmask='255.0.0.0'
network.globals=globals
network.globals.ula_prefix='fd8d:fcc2:d3a6::/48'
network.lan=interface
network.lan.type='bridge'
network.lan.ifname='eth0'
network.lan.proto='static'
network.lan.ipaddr='192.168.1.1'
network.lan.netmask='255.255.255.0'
network.lan.ip6assign='60'
network.wan=interface
network.wan.ifname='eth1'
network.wan.proto='dhcp'
network.wan6=interface
network.wan6.ifname='eth1'
network.wan6.proto='dhcpv6'
network.@switch[0]=switch
network.@switch[0].name='switch0'
network.@switch[0].reset='1'
network.@switch[0].enable_vlan='1'
network.@switch_vlan[0]=switch_vlan
network.@switch_vlan[0].device='switch0'
network.@switch_vlan[0].vlan='1'
network.@switch_vlan[0].ports='3 4 0'

Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment
Labels
Projects
None yet
Development

No branches or pull requests

1 participant